C106M1G - LITTELFUSE - Datasheet.Cloud

Speciﬁcations are subject to change without notice.

Revised: 08/11/20

Thyristors

Surface Mount > 200 - 600V > C106 Series

• Glassivated Surface for

Reliability and Uniformity

• Power Rated at

Economical Prices

• Practical Level

Triggering and Holding

Characteristics

• Flat, Rugged, Thermopad

Construction for Low

Thermal Resistance, High

Heat Dissipation and

Durability

• Sensitive Gate Triggering

• These are Pb−Free

Devices

Features

Glassivated PNPN devices designed for high volume

consumer applications such as temperature, light, and

speed control; process and remote control, and warning

systems where reliability of operation is important.

Description

C106 Series

Functional Diagram

Additional Information

Samples

Resources

Datasheet

Pin Out

K,1

G,3

A,2

TO-225A A

Case 77

Style 2

321

Speciﬁcations are subject to change without notice.

Revised: 08/11/20

Thyristors

Surface Mount > 200 - 600V > C106 Series

Rating Symbol Value Unit

Peak Repetitive Off−State Voltage

(Sine Wave, 50−60 Hz, RGK = 1 K,

TC = −40° to 110°C)

C106B

C106D, C106D1*

C106M

VDRM,

VRRM

200

400

600 V

On-State RMS Current (180° Conduction Angles, TC = 80°C) IT (RMS) 4.0 A

Average On−State Current (180° Conduction Angles, TC = 80°C) IT(AV) 2.55 A

Peak Non-Repetitive Surge Current

(1/2 Cycle, Sine Wave, 60 Hz, TJ = +25°C) ITSM 20 A

Circuit Fusing Considerations (t = 8.3 ms) I2t 1.65 A2s

Forward Peak Gate Current

(Pulse Width 1.0 sec, TC = 80°C) IGM 0.2 A

Forward Peak Gate Power (Pulse Width ≤ 1.0 µsec, TC = 80°C) PGM 0.5 W

Forward Average Gate Power (Pulse Width ≤ 1.0 µsec, TC = 80°C) PG(AV) 0.1 W

Operating Junction Temperature Range TJ-40 to +110 °C

Storage Temperature Range Tstg -40 to +150 °C

Mounting Torque (Note 2) _ 6.0 in. lb.

Maximum Ratings (TJ = 25°C unless otherwise noted)

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the

Recommended Operating Conditions may affect device reliability.

1. VDRM and VRRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages

shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded.

2. Torque rating applies with use of torque washer (Shakeproof WD19523 or equivalent). Mounting Torque in excess of 6 in. lb. does not appreciably lower case-to-sink thermal resistance. Main terminal 2 and heat-sink contact pad

are common.

Thermal Characteristics

Rating Symbol Value Unit

Thermal Resistance, Junction−to−Case (AC)

Junction−to−Ambient RƟJC

RƟJA

3.0

75 °C/W

Maximum Lead Temperature for Soldering Purposes, 1/8” from case for

10 seconds TL260 °C

Electrical Characteristics - OFF (TJ = 25°C unless otherwise noted)

Electrical Characteristics - ON (TJ = 25°C unless otherwise noted)

Characteristic Symbol Min Ty p Max Unit

Peak Repetitive Forward or Reverse Blocking Current

(VAK = Rated VDRM or VRRM, RGK = 1 Ωk)

TJ = 25°C IDRM, IRRM

_ _ 10 μA

TJ = 110°C – – 100 µA

Characteristic Symbol Min Ty p Max Unit

Peak Forward On-State Voltage (Note 3) (ITM = 4 A) VTM – – 2.2 V

Gate Trigger Current (Continuous dc)

(VD = 12 V, RL = 100 Ω, All Quadrants)

TJ = 25°C IGT

_15 200 µA

TJ = -40°C – 35 500

Peak Reverse Gate Voltage (IGR = 10 µA) VGRM – – 6.0 V

Gate Trigger Voltage (Continuous dc)

(VD = 12 Vdc, RL = 100 Ω, TC = 25°C)

TJ = 25°C VGT

0.4 0.60 0.8 V

TJ = -40°C 0.5 0.75 1.0

Gate Non−Trigger Voltage (Continuous dc) (Note 4)

(VAK = 12 V, RL = 100

(VAK = 12 V, RL = 100 , TJ = 110°C), TJ = 110°C) VGD 0.2 _ _ V

Latching Current

(VAK = 12 V, IG = 20 mA, RGK = 1 kΩ)

TJ = 25°C IL

_ 0.20 5.0 mA

TJ = -40°C – 0.35 7. 0

Holding Current

(VD = 12 Vdc)

(Initiating Current = 20 mA, RGK = 1 kΩ)

TJ = 25°C

_ 0.19 3.0

TJ = -40°C _ 0.33 6.0

TJ = +110°C _ 0.07 2.0

Speciﬁcations are subject to change without notice.

Revised: 08/11/20

Thyristors

Surface Mount > 200 - 600V > C106 Series

Dynamic Characteristics

Characteristic Symbol Min Ty p Max Unit

Critical Rate-of-Rise of Off State Voltage

(VAK = Rated VDRM, Exponential Waveform, RGK = 1kΩ,TJ = 110°C) dv/dt – 8.0 − V/µs

3. Pulse Test: Pulse Width ≤ 2.0 ms, Duty Cycle ≤ 2%.

4. RGK is not included in measurement.

Voltage Current Characteristic of SCR

Symbol Parameter

VDRM Peak Repetitive Forward Off State Voltage

IDRM Peak Forward Blocking Current

VRRM Peak Repetitive Reverse Off State Voltage

IRRM Peak Reverse Blocking Current

VTM Maximum On State Voltage

IHHolding Current

+Current

Quadrant 1

Main Terminal 2 +

VTM

On State

Off State IDRM at VDRM

+Voltage

IRRM at VRRM

Quadrant 3

Main Terminal 2 -

VTM

Speciﬁcations are subject to change without notice.

Revised: 08/11/20

Thyristors

Surface Mount > 200 - 600V > C106 Series

Figure 1. Average Current Derating

Figure 3. Typical Gate Trigger Current vs. Junction Temp

Figure 5. Typical Gate Trigger Voltage vs. Junction Temp

Figure 2. Maximum On-State Power Dissipation

Figure 4. Typical Holding Current vs. Junction Temp

Figure 5. Typical Latching Current vs. Junction Temp

Speciﬁcations are subject to change without notice.

Revised: 08/11/20

Thyristors

Surface Mount > 200 - 600V > C106 Series

Dimensions Part Marking System

Pin Assignment

1 Cathode

2 Anode

3 Gate

Ordering Information

Device Package Shipping

C106BG

TO225AA

(Pb-Free)

2500 Units/Box

C106DG

C106D1G*

C106MG

C106M1G*

C106MTG 60 Units/Tube

1920 Units/Box

*D1 signiﬁes European equivalent for D sufﬁx and M1 signiﬁes

European equivalent for M sufﬁx.

Dim Inches Millimeters

Min Max Min Max

A0.102 0.110 2.60 2.80

A1 0.047 0.055 1.20 1.40

b0.028 0.034 0.70 0.86

b2 0.028 0.034 0.70 0.86

c0.019 0.022 0.49 0.57

D0.417 0.449 10.60 11.40

E0.291 0.323 7.40 8.20

e0.090 TYP 2.29 TYP

L0.551 0.630 14.00 16.00

L1 0.091 0.106 2.30 2.70

P0.118 0.134 3.00 3.40

Q0.142 0.157 3.60 4.00

b1 0.047 0.055 1.2 1.4

Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are

not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics.

1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.

2. CONTROLLING DIMENSION: INCH.

3. 077-01 THRU -08 OBSOLETE, NEW STANDARD 077-09.

123

ØP

e e c

b2 x2

PIN4

BACKSIDE TAB

C106xxG

YMAXX

Y=Year

M=Month

A=Assembly Site

XX =Lot Serial Code

C106xx =Device Code

xx =B, D, D1, M, M1

G=Pb-Free Package

TO-225A A

Case 07 7

Style 2

1. Cathode

2. Anode

3. Gate