LM2596
www.ti.com
SNVS124C NOVEMBER 1999REVISED APRIL 2013
LM2596 SIMPLE SWITCHER
®
Power Converter 150 kHz
3A Step-Down Voltage Regulator
Check for Samples: LM2596
1FEATURES DESCRIPTION
The LM2596 series of regulators are monolithic
23 3.3V, 5V, 12V, and Adjustable Output Versions integrated circuits that provide all the active functions
Adjustable Version Output Voltage Range, for a step-down (buck) switching regulator, capable of
1.2V to 37V ±4% Max Over Line and Load driving a 3A load with excellent line and load
Conditions regulation. These devices are available in fixed output
voltages of 3.3V, 5V, 12V, and an adjustable output
Available in TO-220 and TO-263 Packages version.
Ensured 3A Output Load Current Requiring a minimum number of external
Input Voltage Range Up to 40V components, these regulators are simple to use and
Requires Only 4 External Components include internal frequency compensation , and a
Excellent Line and Load Regulation fixed-frequency oscillator.
Specifications The LM2596 series operates at a switching frequency
150 kHz Fixed Frequency Internal Oscillator of 150 kHz thus allowing smaller sized filter
TTL Shutdown Capability components than what would be needed with lower
frequency switching regulators. Available in a
Low Power Standby Mode, IQTypically 80 μAstandard 5-lead TO-220 package with several
High Efficiency different lead bend options, and a 5-lead TO-263
Uses Readily Available Standard Inductors surface mount package.
Thermal Shutdown and Current Limit A standard series of inductors are available from
Protection several different manufacturers optimized for use with
the LM2596 series. This feature greatly simplifies the
APPLICATIONS design of switch-mode power supplies.
Simple High-Efficiency Step-Down (Buck) Other features include a ensured ±4% tolerance on
Regulator output voltage under specified input voltage and
output load conditions, and ±15% on the oscillator
On-Card Switching Regulators frequency. External shutdown is included, featuring
Positive to Negative Converter typically 80 μA standby current. Self protection
features include a two stage frequency reducing
current limit for the output switch and an over
temperature shutdown for complete protection under
fault conditions. (1)
(1) Patent Number 5,382,918.
Typical Application
(Fixed Output Voltage Versions)
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2SIMPLE SWITCHER is a registered trademark of Texas Instruments.
3All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 1999–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
LM2596
SNVS124C NOVEMBER 1999REVISED APRIL 2013
www.ti.com
Connection Diagrams
Figure 1. 5-Lead Bent and Staggered Leads, Figure 2. 5-Lead DDPAK/TO-263 (S) Package
Through Hole TO-220 (T) Package See Package Number KTT0005B
See Package Number NDH0005D
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1)(2)
Maximum Supply Voltage 45V
ON /OFF Pin Input Voltage 0.3 V+25V
Feedback Pin Voltage 0.3 V+25V
Output Voltage to Ground (Steady State) 1V
Power Dissipation Internally limited
Storage Temperature Range 65°C to +150°C
ESD Susceptibility
Human Body Model (3) 2 kV
Lead Temperature
DDPAK/TO-263 Package
Vapor Phase (60 sec.) +215°C
Infrared (10 sec.) +245°C
TO-220 Package (Soldering, 10 sec.) +260°C
Maximum Junction Temperature +150°C
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but do not ensure specific performance limits. For ensured specifications and test
conditions, see the Electrical Characteristics.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) The human body model is a 100 pF capacitor discharged through a 1.5k resistor into each pin.
Operating Conditions
Temperature Range 40°C TJ+125°C
Supply Voltage 4.5V to 40V
2Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2596
LM2596
www.ti.com
SNVS124C NOVEMBER 1999REVISED APRIL 2013
LM2596-3.3 Electrical Characteristics
Specifications with standard type face are for TJ= 25°C, and those with boldface type apply over full Operating
Temperature Range
LM2596-3.3 Units
Symbol Parameter Conditions Typ Limit (Limits)
(1) (2)
SYSTEM PARAMETERS (3) Test Circuit Figure 20
VOUT Output Voltage 4.75V VIN 40V, 0.2A ILOAD 3A 3.3 V
3.168/3.135 V(min)
3.432/3.465 V(max)
ηEfficiency VIN = 12V, ILOAD = 3A 73 %
(1) Typical numbers are at 25°C and represent the most likely norm.
(2) All limits specified at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature limits
are 100% production tested. All limits at temperature extremes are ensured via correlation using standard Statistical Quality Control
(SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).
(3) External components such as the catch diode, inductor, input and output capacitors, and voltage programming resistors can affect
switching regulator system performance. When the LM2596 is used as shown in the Figure 20 test circuit, system performance will be
as shown in system parameters of Electrical Characteristics section.
LM2596-5.0 Electrical Characteristics
Specifications with standard type face are for TJ= 25°C, and those with boldface type apply over full Operating
Temperature Range
LM2596-5.0 Units
Symbol Parameter Conditions Typ Limit (Limits)
(1) (2)
SYSTEM PARAMETERS (3) Test Circuit Figure 20
VOUT Output Voltage 7V VIN 40V, 0.2A ILOAD 3A 5.0 V
4.800/4.750 V(min)
5.200/5.250 V(max)
ηEfficiency VIN = 12V, ILOAD = 3A 80 %
(1) Typical numbers are at 25°C and represent the most likely norm.
(2) All limits specified at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature limits
are 100% production tested. All limits at temperature extremes are ensured via correlation using standard Statistical Quality Control
(SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).
(3) External components such as the catch diode, inductor, input and output capacitors, and voltage programming resistors can affect
switching regulator system performance. When the LM2596 is used as shown in the Figure 20 test circuit, system performance will be
as shown in system parameters of Electrical Characteristics section.
LM2596-12 Electrical Characteristics
Specifications with standard type face are for TJ= 25°C, and those with boldface type apply over full Operating
Temperature Range
LM2596-12 Units
Symbol Parameter Conditions Typ Limit (Limits)
(1) (2)
SYSTEM PARAMETERS (3) Test Circuit Figure 20
VOUT Output Voltage 15V VIN 40V, 0.2A ILOAD 3A 12.0 V
11.52/11.40 V(min)
12.48/12.60 V(max)
ηEfficiency VIN = 25V, ILOAD = 3A 90 %
(1) Typical numbers are at 25°C and represent the most likely norm.
(2) All limits specified at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature limits
are 100% production tested. All limits at temperature extremes are ensured via correlation using standard Statistical Quality Control
(SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).
(3) External components such as the catch diode, inductor, input and output capacitors, and voltage programming resistors can affect
switching regulator system performance. When the LM2596 is used as shown in the Figure 20 test circuit, system performance will be
as shown in system parameters of Electrical Characteristics section.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM2596
LM2596
SNVS124C NOVEMBER 1999REVISED APRIL 2013
www.ti.com
LM2596-ADJ Electrical Characteristics
Specifications with standard type face are for TJ= 25°C, and those with boldface type apply over full Operating
Temperature Range
LM2596-ADJ Units
Symbol Parameter Conditions Typ Limit (Limits)
(1) (2)
SYSTEM PARAMETERS (3) Test Circuit Figure 20
VFB Feedback Voltage 4.5V VIN 40V, 0.2A ILOAD 3A 1.230 V
VOUT programmed for 3V. Circuit of Figure 20 1.193/1.180 V(min)
1.267/1.280 V(max)
ηEfficiency VIN = 12V, VOUT = 3V, ILOAD = 3A 73 %
(1) Typical numbers are at 25°C and represent the most likely norm.
(2) All limits specified at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature limits
are 100% production tested. All limits at temperature extremes are ensured via correlation using standard Statistical Quality Control
(SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).
(3) External components such as the catch diode, inductor, input and output capacitors, and voltage programming resistors can affect
switching regulator system performance. When the LM2596 is used as shown in the Figure 20 test circuit, system performance will be
as shown in system parameters of Electrical Characteristics section.
All Output Voltage Versions Electrical Characteristics
Specifications with standard type face are for TJ= 25°C, and those with boldface type apply over full Operating
Temperature Range. Unless otherwise specified, VIN = 12V for the 3.3V, 5V, and Adjustable version and VIN = 24V for the
12V version. ILOAD = 500 mA LM2596-XX Units
Symbol Parameter Conditions Typ Limit (Limits)
(1) (2)
DEVICE PARAMETERS
IbFeedback Bias Current Adjustable Version Only, VFB = 1.3V 10 nA
50/100 nA (max)
fOOscillator Frequency See (3) 150 kHz
127/110 kHz(min)
173/173 kHz(max)
VSAT Saturation Voltage IOUT = 3A (4) (5) 1.16 V
1.4/1.5 V(max)
DC Max Duty Cycle (ON) See (5) 100 %
Min Duty Cycle (OFF) See (6) 0
ICL Current Limit Peak Current (4)(5) 4.5 A
3.6/3.4 A(min)
6.9/7.5 A(max)
ILOutput Leakage Current Output = 0V (4)(6) 50 μA(max)
Output = 1V (7) 2 mA
30 mA(max)
IQQuiescent Current See (6) 5 mA
10 mA(max)
(1) Typical numbers are at 25°C and represent the most likely norm.
(2) All limits specified at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature limits
are 100% production tested. All limits at temperature extremes are ensured via correlation using standard Statistical Quality Control
(SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).
(3) The switching frequency is reduced when the second stage current limit is activated.
(4) No diode, inductor or capacitor connected to output pin.
(5) Feedback pin removed from output and connected to 0V to force the output transistor switch ON.
(6) Feedback pin removed from output and connected to 12V for the 3.3V, 5V, and the ADJ. version, and 15V for the 12V version, to force
the output transistor switch OFF.
(7) VIN = 40V.
4Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2596
LM2596
www.ti.com
SNVS124C NOVEMBER 1999REVISED APRIL 2013
All Output Voltage Versions Electrical Characteristics (continued)
Specifications with standard type face are for TJ= 25°C, and those with boldface type apply over full Operating
Temperature Range. Unless otherwise specified, VIN = 12V for the 3.3V, 5V, and Adjustable version and VIN = 24V for the
12V version. ILOAD = 500 mA LM2596-XX Units
Symbol Parameter Conditions Typ Limit (Limits)
(1) (2)
ISTBY Standby Quiescent Current ON/OFF pin = 5V (OFF) (7) 80 μA
200/250 μA(max)
θJC Thermal Resistance TO-220 or TO-263 Package, Junction to Case 2 °C/W
θJA TO-220 Package, Junction to Ambient (8) 50 °C/W
θJA TO-263 Package, Junction to Ambient (9) 50 °C/W
θJA TO-263 Package, Junction to Ambient (10) 30 °C/W
θJA TO-263 Package, Junction to Ambient (11) 20 °C/W
ON/OFF CONTROL Test Circuit Figure 20
ON /OFF Pin Logic Input 1.3 V
VIH Threshold Voltage Low (Regulator ON) 0.6 V(max)
VIL High (Regulator OFF) 2.0 V(min)
IHON /OFF Pin Input Current VLOGIC = 2.5V (Regulator OFF) 5 μA
15 μA(max)
ILVLOGIC = 0.5V (Regulator ON) 0.02 μA
5μA(max)
(8) Junction to ambient thermal resistance (no external heat sink) for the TO-220 package mounted vertically, with the leads soldered to a
printed circuit board with (1 oz.) copper area of approximately 1 in2.
(9) Junction to ambient thermal resistance with the TO-263 package tab soldered to a single printed circuit board with 0.5 in2of (1 oz.)
copper area.
(10) Junction to ambient thermal resistance with the TO-263 package tab soldered to a single sided printed circuit board with 2.5 in2of (1
oz.) copper area.
(11) Junction to ambient thermal resistance with the TO-263 package tab soldered to a double sided printed circuit board with 3 in2of (1 oz.)
copper area on the LM2596S side of the board, and approximately 16 in2of copper on the other side of the p-c board. See Application
Information in this data sheet and the thermal model in Switchers Made Simple™ version 4.3 software.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM2596
LM2596
SNVS124C NOVEMBER 1999REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics
(Circuit of Figure 20)
Normalized
Output Voltage Line Regulation
Figure 3. Figure 4.
Switch Saturation
Efficiency Voltage
Figure 5. Figure 6.
Switch Current Limit Dropout Voltage
Figure 7. Figure 8.
6Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2596
LM2596
www.ti.com
SNVS124C NOVEMBER 1999REVISED APRIL 2013
Typical Performance Characteristics (continued)
(Circuit of Figure 20)Operating Shutdown
Quiescent Current Quiescent Current
Figure 9. Figure 10.
Minimum Operating ON /OFF Threshold
Supply Voltage Voltage
Figure 11. Figure 12.
ON /OFF Pin
Current (Sinking) Switching Frequency
Figure 13. Figure 14.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM2596
LM2596
SNVS124C NOVEMBER 1999REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
(Circuit of Figure 20)Continuous Mode Switching Waveforms
Feedback Pin VIN = 20V, VOUT = 5V, ILOAD = 2A
Bias Current L = 32 μH, COUT = 220 μF, COUT ESR = 50 mΩ
A: Output Pin Voltage, 10V/div.
B: Inductor Current 1A/div.
C: Output Ripple Voltage, 50 mV/div.
Figure 15. Figure 16. Horizontal Time Base: 2 μs/div.
Discontinuous Mode Switching Waveforms Load Transient Response for Continuous Mode
VIN = 20V, VOUT = 5V, ILOAD = 500 mA VIN = 20V, VOUT = 5V, ILOAD = 500 mA to 2A
L = 10 μH, COUT = 330 μF, COUT ESR = 45 mΩL = 32 μH, COUT = 220 μF, COUT ESR = 50 mΩ
A: Output Voltage, 100 mV/div. (AC)
A: Output Pin Voltage, 10V/div. B: 500 mA to 2A Load Pulse
B: Inductor Current 0.5A/div.
C: Output Ripple Voltage, 100 mV/div.
Figure 17. Horizontal Time Base: 2 μs/div. Figure 18. Horizontal Time Base: 100 μs/div.
Load Transient Response for Discontinuous Mode
VIN = 20V, VOUT = 5V, ILOAD = 500 mA to 2A
L = 10 μH, COUT = 330 μF, COUT ESR = 45 mΩ
A: Output Voltage, 100 mV/div. (AC)
B: 500 mA to 2A Load Pulse Figure 19. Horizontal Time Base: 200 μs/div.
8Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2596
LM2596
www.ti.com
SNVS124C NOVEMBER 1999REVISED APRIL 2013
Test Circuit and Layout Guidelines
Fixed Output Voltage Versions
CIN —470 μF, 50V, Aluminum Electrolytic Nichicon “PL Series”
COUT —220 μF, 25V Aluminum Electrolytic, Nichicon “PL Series”
D1 —5A, 40V Schottky Rectifier, 1N5825
L1 —68 μH, L38
Adjustable Output Voltage Versions
where VREF = 1.23V
Select R1to be approximately 1 k, use a 1% resistor for best stability.
CIN —470 μF, 50V, Aluminum Electrolytic Nichicon “PL Series”
COUT —220 μF, 35V Aluminum Electrolytic, Nichicon “PL Series”
D1 —5A, 40V Schottky Rectifier, 1N5825
L1 —68 μH, L38
R1 —1 kΩ, 1%
CFF —See Application Information Section
Figure 20. Standard Test Circuits and Layout Guides
As in any switching regulator, layout is very important. Rapidly switching currents associated with wiring
inductance can generate voltage transients which can cause problems. For minimal inductance and ground
loops, the wires indicated by heavy lines should be wide printed circuit traces and should be kept as short
as possible. For best results, external components should be located as close to the switcher lC as possible
using ground plane construction or single point grounding.
If open core inductors are used, special care must be taken as to the location and positioning of this type of
inductor. Allowing the inductor flux to intersect sensitive feedback, lC groundpath and COUT wiring can cause
problems.
When using the adjustable version, special care must be taken as to the location of the feedback resistors and
the associated wiring. Physically locate both resistors near the IC, and route the wiring away from the inductor,
especially an open core type of inductor. (See Application Information section for more information.)
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM2596
LM2596
SNVS124C NOVEMBER 1999REVISED APRIL 2013
www.ti.com
LM2596 Series Buck Regulator Design Procedure (Fixed Output)
PROCEDURE (Fixed Output Voltage Version) EXAMPLE (Fixed Output Voltage Version)
Given: Given:
VOUT = Regulated Output Voltage (3.3V, 5V or 12V) VOUT = 5V
VIN(max) = Maximum DC Input Voltage VIN(max) = 12V
ILOAD(max) = Maximum Load Current ILOAD(max) = 3A
1. Inductor Selection (L1) 1. Inductor Selection (L1)
A. Select the correct inductor value selection guide from Figures A. Use the inductor selection guide for the 5V version shown in
Figure 21,Figure 22, or Figure 23. (Output voltages of 3.3V, 5V, or Figure 22.
12V respectively.) For all other voltages, see the Design Procedure B. From the inductor value selection guide shown in Figure 22, the
for the adjustable version. inductance region intersected by the 12V horizontal line and the 3A
B. From the inductor value selection guide, identify the inductance vertical line is 33 μH, and the inductor code is L40.
region intersected by the Maximum Input Voltage line and the C. The inductance value required is 33 μH. From the table in
Maximum Load Current line. Each region is identified by an Table 3, go to the L40 line and choose an inductor part number from
inductance value and an inductor code (LXX). any of the four manufacturers shown. (In most instance, both
C. Select an appropriate inductor from the four manufacturer's part through hole and surface mount inductors are available.)
numbers listed in Table 3.
2. Output Capacitor Selection (COUT) 2. Output Capacitor Selection (COUT)
A. In the majority of applications, low ESR (Equivalent Series A. See section on output capacitors in Application Information
Resistance) electrolytic capacitors between 82 μF and 820 μF and section.
low ESR solid tantalum capacitors between 10 μF and 470 μFB. From the quick design component selection table shown in
provide the best results. This capacitor should be located close to Table 1, locate the 5V output voltage section. In the load current
the IC using short capacitor leads and short copper traces. Do not column, choose the load current line that is closest to the current
use capacitors larger than 820 μF . needed in your application, for this example, use the 3A line. In the
For additional information, see section on output capacitors in maximum input voltage column, select the line that covers the input
Application Information section. voltage needed in your application, in this example, use the 15V line.
Continuing on this line are recommended inductors and capacitors
B. To simplify the capacitor selection procedure, refer to the quick that will provide the best overall performance.
design component selection table shown in Table 1. This table
contains different input voltages, output voltages, and load currents, The capacitor list contains both through hole electrolytic and surface
and lists various inductors and output capacitors that will provide the mount tantalum capacitors from four different capacitor
best design solutions. manufacturers. It is recommended that both the manufacturers and
the manufacturer's series that are listed in the table be used.
C. The capacitor voltage rating for electrolytic capacitors should be
at least 1.5 times greater than the output voltage, and often much In this example aluminum electrolytic capacitors from several
higher voltage ratings are needed to satisfy the low ESR different manufacturers are available with the range of ESR numbers
requirements for low output ripple voltage. needed.
D. For computer aided design software, see Switchers Made 330 μF 35V Panasonic HFQ Series
Simple™ version 4.3 or later. 330 μF 35V Nichicon PL Series
C. For a 5V output, a capacitor voltage rating at least 7.5V or more
is needed. But even a low ESR, switching grade, 220 μF 10V
aluminum electrolytic capacitor would exhibit approximately 225 mΩ
of ESR (see the curve in Figure 26 for the ESR vs voltage rating).
This amount of ESR would result in relatively high output ripple
voltage. To reduce the ripple to 1% of the output voltage, or less, a
capacitor with a higher value or with a higher voltage rating (lower
ESR) should be selected. A 16V or 25V capacitor will reduce the
ripple voltage by approximately half.
10 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2596
LM2596
www.ti.com
SNVS124C NOVEMBER 1999REVISED APRIL 2013
PROCEDURE (Fixed Output Voltage Version) EXAMPLE (Fixed Output Voltage Version)
3. Catch Diode Selection (D1) 3. Catch Diode Selection (D1)
A. The catch diode current rating must be at least 1.3 times greater A. Refer to the table shown in Table 6. In this example, a 5A, 20V,
than the maximum load current. Also, if the power supply design 1N5823 Schottky diode will provide the best performance, and will
must withstand a continuous output short, the diode should have a not be overstressed even for a shorted output.
current rating equal to the maximum current limit of the LM2596. The
most stressful condition for this diode is an overload or shorted
output condition.
B. The reverse voltage rating of the diode should be at least 1.25
times the maximum input voltage.
C. This diode must be fast (short reverse recovery time) and must be
located close to the LM2596 using short leads and short printed
circuit traces. Because of their fast switching speed and low forward
voltage drop, Schottky diodes provide the best performance and
efficiency, and should be the first choice, especially in low output
voltage applications. Ultra-fast recovery, or High-Efficiency rectifiers
also provide good results. Ultra-fast recovery diodes typically have
reverse recovery times of 50 ns or less. Rectifiers such as the
1N5400 series are much too slow and should not be used.
4. Input Capacitor (CIN) 4. Input Capacitor (CIN)
A low ESR aluminum or tantalum bypass capacitor is needed The important parameters for the Input capacitor are the input
between the input pin and ground pin to prevent large voltage voltage rating and the RMS current rating. With a nominal input
transients from appearing at the input. This capacitor should be voltage of 12V, an aluminum electrolytic capacitor with a voltage
located close to the IC using short leads. In addition, the RMS rating greater than 18V (1.5 × VIN) would be needed. The next
current rating of the input capacitor should be selected to be at least higher capacitor voltage rating is 25V.
½ the DC load current. The capacitor manufacturers data sheet must The RMS current rating requirement for the input capacitor in a buck
be checked to assure that this current rating is not exceeded. The regulator is approximately ½ the DC load current. In this example,
curve shown in Figure 25 shows typical RMS current ratings for with a 3A load, a capacitor with a RMS current rating of at least 1.5A
several different aluminum electrolytic capacitor values. is needed. The curves shown in Figure 25 can be used to select an
For an aluminum electrolytic, the capacitor voltage rating should be appropriate input capacitor. From the curves, locate the 35V line and
approximately 1.5 times the maximum input voltage. Caution must note which capacitor values have RMS current ratings greater than
be exercised if solid tantalum capacitors are used (see Application 1.5A. A 680 μF/35V capacitor could be used.
Information on input capacitor). The tantalum capacitor voltage rating For a through hole design, a 680 μF/35V electrolytic capacitor
should be 2 times the maximum input voltage and it is recommended (Panasonic HFQ series or Nichicon PL series or equivalent) would
that they be surge current tested by the manufacturer. be adequate. other types or other manufacturers capacitors can be
Use caution when using ceramic capacitors for input bypassing, used provided the RMS ripple current ratings are adequate.
because it may cause severe ringing at the VIN pin. For surface mount designs, solid tantalum capacitors can be used,
For additional information, see section on input capacitors in but caution must be exercised with regard to the capacitor surge
Application Information section. current rating (see Application Information on input capacitors in this
data sheet). The TPS series available from AVX, and the 593D
series from Sprague are both surge current tested.
Table 1. LM2596 Fixed Voltage Quick Design Component Selection Table
Conditions Inductor Output Capacitor
Through Hole Electrolytic Surface Mount Tantalum
Output Load Max Input Panasonic Nichicon AVX TPS Sprague
Inductance Inductor
Voltage Current Voltage HFQ Series PL Series Series 595D Series
(μH) (#)
(V) (A) (V) (μF/V) (μF/V) (μF/V) (μF/V)
3.3 3 5 22 L41 470/25 560/16 330/6.3 390/6.3
7 22 L41 560/35 560/35 330/6.3 390/6.3
10 22 L41 680/35 680/35 330/6.3 390/6.3
40 33 L40 560/35 470/35 330/6.3 390/6.3
6 22 L33 470/25 470/35 330/6.3 390/6.3
2 10 33 L32 330/35 330/35 330/6.3 390/6.3
40 47 L39 330/35 270/50 220/10 330/10
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM2596
LM2596
SNVS124C NOVEMBER 1999REVISED APRIL 2013
www.ti.com
Table 1. LM2596 Fixed Voltage Quick Design Component Selection Table (continued)
Conditions Inductor Output Capacitor
Through Hole Electrolytic Surface Mount Tantalum
Output Load Max Input Panasonic Nichicon AVX TPS Sprague
Inductance Inductor
Voltage Current Voltage HFQ Series PL Series Series 595D Series
(μH) (#)
(V) (A) (V) (μF/V) (μF/V) (μF/V) (μF/V)
53 8 22 L41 470/25 560/16 220/10 330/10
10 22 L41 560/25 560/25 220/10 330/10
15 33 L40 330/35 330/35 220/10 330/10
40 47 L39 330/35 270/35 220/10 330/10
9 22 L33 470/25 560/16 220/10 330/10
2 20 68 L38 180/35 180/35 100/10 270/10
40 68 L38 180/35 180/35 100/10 270/10
12 3 15 22 L41 470/25 470/25 100/16 180/16
18 33 L40 330/25 330/25 100/16 180/16
30 68 L44 180/25 180/25 100/16 120/20
40 68 L44 180/35 180/35 100/16 120/20
15 33 L32 330/25 330/25 100/16 180/16
2 20 68 L38 180/25 180/25 100/16 120/20
40 150 L42 82/25 82/25 68/20 68/25
LM2596 Series Buck Regulator Design Procedure (Adjustable Output)
PROCEDURE (Adjustable Output Voltage Version) EXAMPLE (Adjustable Output Voltage Version)
Given: Given:
VOUT = Regulated Output Voltage VOUT = 20V
VIN(max) = Maximum Input Voltage VIN(max) = 28V
ILOAD(max) = Maximum Load Current ILOAD(max) = 3A
F = Switching Frequency (Fixed at a nominal 150 kHz). F = Switching Frequency (Fixed at a nominal 150 kHz).
1. Programming Output Voltage (Selecting R1and R2, as shown in 1. Programming Output Voltage (Selecting R1and R2, as shown in
Figure 20 )Figure 20 )
Use the following formula to select the appropriate resistor values. Select R1to be 1 kΩ, 1%. Solve for R2.
(3)
(1) R2= 1k (16.26 1) = 15.26k, closest 1% value is 15.4 kΩ.
Select a value for R1between 240Ωand 1.5 kΩ. The lower resistor
values minimize noise pickup in the sensitive feedback pin. (For the R2= 15.4 kΩ.
lowest temperature coefficient and the best stability with time, use
1% metal film resistors.)
(2)
12 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2596
LM2596
www.ti.com
SNVS124C NOVEMBER 1999REVISED APRIL 2013
PROCEDURE (Adjustable Output Voltage Version) EXAMPLE (Adjustable Output Voltage Version)
2. Inductor Selection (L1) 2. Inductor Selection (L1)
A. Calculate the inductor Volt microsecond constant E T (V μs), A. Calculate the inductor Volt microsecond constant
from the following formula: (E T),
where (5)
VSAT = internal switch saturation voltage = B. E T = 34.2 (V μs)
1.16V C. ILOAD(max) = 3A
VD= diode forward voltage drop = 0.5V (4) D. From the inductor value selection guide shown in Figure 24, the
inductance region intersected by the 34 (V μs) horizontal line and
the 3A vertical line is 47 μH, and the inductor code is L39.
B. Use the E T value from the previous formula and match it with
the E T number on the vertical axis of the Inductor Value Selection E. From the table in Table 3,locate line L39, and select an inductor
Guide shown in Figure 24.part number from the list of manufacturers part numbers.
C. on the horizontal axis, select the maximum load current.
D. Identify the inductance region intersected by the E T value and
the Maximum Load Current value. Each region is identified by an
inductance value and an inductor code (LXX).
E. Select an appropriate inductor from the four manufacturer's part
numbers listed in Table 3.
3. Output Capacitor Selection (COUT) 3. Output Capacitor SeIection (COUT)
A. In the majority of applications, low ESR electrolytic or solid A. See section on COUT in Application Information section.
tantalum capacitors between 82 μF and 820 μF provide the best B. From the quick design table shown in Table 2, locate the output
results. This capacitor should be located close to the IC using short voltage column. From that column, locate the output voltage closest
capacitor leads and short copper traces. Do not use capacitors to the output voltage in your application. In this example, select the
larger than 820 μF. For additional information, see section on 24V line. Under the OUTPUT CAPACITOR section, select a
output capacitors in Application Information section. capacitor from the list of through hole electrolytic or surface mount
B. To simplify the capacitor selection procedure, refer to the quick tantalum types from four different capacitor manufacturers. It is
design table shown in Table 2. This table contains different output recommended that both the manufacturers and the manufacturers
voltages, and lists various output capacitors that will provide the best series that are listed in the table be used.
design solutions. In this example, through hole aluminum electrolytic capacitors from
C. The capacitor voltage rating should be at least 1.5 times greater several different manufacturers are available.
than the output voltage, and often much higher voltage ratings are 220 μF/35V Panasonic HFQ Series
needed to satisfy the low ESR requirements needed for low output 150 μF/35V Nichicon PL Series
ripple voltage. C. For a 20V output, a capacitor rating of at least 30V or more is
needed. In this example, either a 35V or 50V capacitor would work.
A 35V rating was chosen, although a 50V rating could also be used
if a lower output ripple voltage is needed.
Other manufacturers or other types of capacitors may also be used,
provided the capacitor specifications (especially the 100 kHz ESR)
closely match the types listed in the table. Refer to the capacitor
manufacturers data sheet for this information.
4. Feedforward Capacitor (CFF)(See Figure 20)4. Feedforward Capacitor (CFF)
For output voltages greater than approximately 10V, an additional The table shown in Table 2 contains feed forward capacitor values
capacitor is required. The compensation capacitor is typically for various output voltages. In this example, a 560 pF capacitor is
between 100 pF and 33 nF, and is wired in parallel with the output needed.
voltage setting resistor, R2. It provides additional stability for high
output voltages, low input-output voltages, and/or very low ESR
output capacitors, such as solid tantalum capacitors.
(6)
This capacitor type can be ceramic, plastic, silver mica, etc.
(Because of the unstable characteristics of ceramic capacitors made
with Z5U material, they are not recommended.)
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM2596
LM2596
SNVS124C NOVEMBER 1999REVISED APRIL 2013
www.ti.com
PROCEDURE (Adjustable Output Voltage Version) EXAMPLE (Adjustable Output Voltage Version)
5. Catch Diode Selection (D1) 5. Catch Diode Selection (D1)
A. The catch diode current rating must be at least 1.3 times greater A. Refer to the table shown in Table 6. Schottky diodes provide the
than the maximum load current. Also, if the power supply design best performance, and in this example a 5A, 40V, 1N5825 Schottky
must withstand a continuous output short, the diode should have a diode would be a good choice. The 5A diode rating is more than
current rating equal to the maximum current limit of the LM2596. The adequate and will not be overstressed even for a shorted output.
most stressful condition for this diode is an overload or shorted
output condition.
B. The reverse voltage rating of the diode should be at least 1.25
times the maximum input voltage.
C. This diode must be fast (short reverse recovery time) and must be
located close to the LM2596 using short leads and short printed
circuit traces. Because of their fast switching speed and low forward
voltage drop, Schottky diodes provide the best performance and
efficiency, and should be the first choice, especially in low output
voltage applications. Ultra-fast recovery, or High-Efficiency rectifiers
are also a good choice, but some types with an abrupt turn-off
characteristic may cause instability or EMl problems. Ultra-fast
recovery diodes typically have reverse recovery times of 50 ns or
less. Rectifiers such as the 1N4001 series are much too slow and
should not be used.
6. Input Capacitor (CIN) 6. Input Capacitor (CIN)
A low ESR aluminum or tantalum bypass capacitor is needed The important parameters for the Input capacitor are the input
between the input pin and ground to prevent large voltage transients voltage rating and the RMS current rating. With a nominal input
from appearing at the input. In addition, the RMS current rating of voltage of 28V, an aluminum electrolytic aluminum electrolytic
the input capacitor should be selected to be at least ½ the DC load capacitor with a voltage rating greater than 42V (1.5 × VIN) would be
current. The capacitor manufacturers data sheet must be checked to needed. Since the the next higher capacitor voltage rating is 50V, a
assure that this current rating is not exceeded. The curve shown in 50V capacitor should be used. The capacitor voltage rating of (1.5 ×
Figure 25 shows typical RMS current ratings for several different VIN) is a conservative guideline, and can be modified somewhat if
aluminum electrolytic capacitor values. desired.
This capacitor should be located close to the IC using short leads The RMS current rating requirement for the input capacitor of a buck
and the voltage rating should be approximately 1.5 times the regulator is approximately ½ the DC load current. In this example,
maximum input voltage. with a 3A load, a capacitor with a RMS current rating of at least 1.5A
is needed.
If solid tantalum input capacitors are used, it is recomended that they
be surge current tested by the manufacturer. The curves shown in Figure 25 can be used to select an appropriate
input capacitor. From the curves, locate the 50V line and note which
Use caution when using a high dielectric constant ceramic capacitor capacitor values have RMS current ratings greater than 1.5A. Either
for input bypassing, because it may cause severe ringing at the VIN a 470 μF or 680 μF, 50V capacitor could be used.
pin. For a through hole design, a 680 μF/50V electrolytic capacitor
For additional information, see section on input capacitors in (Panasonic HFQ series or Nichicon PL series or equivalent) would
Application Information section. be adequate. Other types or other manufacturers capacitors can be
used provided the RMS ripple current ratings are adequate.
For surface mount designs, solid tantalum capacitors can be used,
but caution must be exercised with regard to the capacitor surge
current rting (see Application Information or input capacitors in this
data sheet). The TPS series available from AVX, and the 593D
series from Sprague are both surge current tested.
To further simplify the buck regulator design procedure, Texas
Instruments is making available computer design software to be
used with the Simple Switcher line ot switching regulators.
Switchers Made Simple (version 4.3 or later) is available on a
diskette for IBM compatible computers.
LM2596 Series Buck Regulator Design Procedure (Adjustable Output)
Table 2. Output Capacitor and Feedforward Capacitor Selection Table
Output Through Hole Output Capacitor Surface Mount Output Capacitor
Voltage Panasonic Nichicon PL AVX TPS Sprague
Feedforward Feedforward
(V) HFQ Series Series Series 595D Series
Capacitor Capacitor
(μF/V) (μF/V) (μF/V) (μF/V)
2820/35 820/35 33 nF 330/6.3 470/4 33 nF
4560/35 470/35 10 nF 330/6.3 390/6.3 10 nF
6470/25 470/25 3.3 nF 220/10 330/10 3.3 nF
14 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2596
LM2596
www.ti.com
SNVS124C NOVEMBER 1999REVISED APRIL 2013
Table 2. Output Capacitor and Feedforward Capacitor Selection Table (continued)
Output Through Hole Output Capacitor Surface Mount Output Capacitor
Voltage Panasonic Nichicon PL AVX TPS Sprague
Feedforward Feedforward
(V) HFQ Series Series Series 595D Series
Capacitor Capacitor
(μF/V) (μF/V) (μF/V) (μF/V)
9330/25 330/25 1.5 nF 100/16 180/16 1.5 nF
1 2 330/25 330/25 1 nF 100/16 180/16 1 nF
1 5 220/35 220/35 680 pF 68/20 120/20 680 pF
2 4 220/35 150/35 560 pF 33/25 33/25 220 pF
2 8 100/50 100/50 390 pF 10/35 15/50 220 pF
LM2596 Series Buck Regulator Design Procedure
INDUCTOR VALUE SELECTION GUIDES
(For Continuous Mode Operation)
Figure 21. LM2596-3.3 Figure 22. LM2596-5.0
Figure 23. LM2596-12 Figure 24. LM2596-ADJ
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM2596
LM2596
SNVS124C NOVEMBER 1999REVISED APRIL 2013
www.ti.com
Table 3. Inductor Manufacturers Part Numbers
Inductance Current Schott Renco Pulse Engineering Coilcraft
(μH) (A) Through Surface Through Surface Through Surface Surface
Hole Mount Hole Mount Hole Mount Mount
L15 22 0.99 67148350 67148460 RL-1284-22-43 RL1500-22 PE-53815 PE-53815-S DO3308-223
L21 68 0.99 67144070 67144450 RL-5471-5 RL1500-68 PE-53821 PE-53821-S DO3316-683
L22 47 1.17 67144080 67144460 RL-5471-6 PE-53822 PE-53822-S DO3316-473
L23 33 1.40 67144090 67144470 RL-5471-7 PE-53823 PE-53823-S DO3316-333
L24 22 1.70 67148370 67148480 RL-1283-22-43 PE-53824 PE-53825-S DO3316-223
L25 15 2.10 67148380 67148490 RL-1283-15-43 PE-53825 PE-53824-S DO3316-153
L26 330 0.80 67144100 67144480 RL-5471-1 PE-53826 PE-53826-S DO5022P-334
L27 220 1.00 67144110 67144490 RL-5471-2 PE-53827 PE-53827-S DO5022P-224
L28 150 1.20 67144120 67144500 RL-5471-3 PE-53828 PE-53828-S DO5022P-154
L29 100 1.47 67144130 67144510 RL-5471-4 PE-53829 PE-53829-S DO5022P-104
L30 68 1.78 67144140 67144520 RL-5471-5 PE-53830 PE-53830-S DO5022P-683
L31 47 2.20 67144150 67144530 RL-5471-6 PE-53831 PE-53831-S DO5022P-473
L32 33 2.50 67144160 67144540 RL-5471-7 PE-53932 PE-53932-S DO5022P-333
L33 22 3.10 67148390 67148500 RL-1283-22-43 PE-53933 PE-53933-S DO5022P-223
L34 15 3.40 67148400 67148790 RL-1283-15-43 PE-53934 PE-53934-S DO5022P-153
L35 220 1.70 67144170 RL-5473-1 PE-53935 PE-53935-S
L36 150 2.10 67144180 RL-5473-4 PE-54036 PE-54036-S
L37 100 2.50 67144190 RL-5472-1 PE-54037 PE-54037-S
L38 68 3.10 67144200 RL-5472-2 PE-54038 PE-54038-S
L39 47 3.50 67144210 RL-5472-3 PE-54039 PE-54039-S
L40 33 3.50 67144220 67148290 RL-5472-4 PE-54040 PE-54040-S
L41 22 3.50 67144230 67148300 RL-5472-5 PE-54041 PE-54041-S
L42 150 2.70 67148410 RL-5473-4 PE-54042 PE-54042-S
L43 100 3.40 67144240 RL-5473-2 PE-54043
L44 68 3.40 67144250 RL-5473-3 PE-54044
Table 4. Inductor Manufacturers Phone Numbers
Coilcraft Inc. Phone (800) 322-2645
FAX (708) 639-1469
Coilcraft Inc., Europe Phone +11 1236 730 595
FAX +44 1236 730 627
Pulse Engineering Inc. Phone (619) 674-8100
FAX (619) 674-8262
Pulse Engineering Inc., Europe Phone +353 93 24 107
FAX +353 93 24 459
Renco Electronics Inc. Phone (800) 645-5828
FAX (516) 586-5562
Schott Corp. Phone (612) 475-1173
FAX (612) 475-1786
Table 5. Capacitor Manufacturers Phone Numbers
Nichicon Corp. Phone (708) 843-7500
FAX (708) 843-2798
Panasonic Phone (714) 373-7857
FAX (714) 373-7102
16 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2596
LM2596
www.ti.com
SNVS124C NOVEMBER 1999REVISED APRIL 2013
Table 5. Capacitor Manufacturers Phone Numbers (continued)
AVX Corp. Phone (803) 448-9411
FAX (803) 448-1943
Sprague/Vishay Phone (207) 324-4140
FAX (207) 324-7223
Table 6. Diode Selection Table
VR 3A Diodes 4A–6A Diodes
Surface Mount Through Hole Surface Mount Through Hole
Schottky Ultra Fast Schottky Ultra Fast Schottky Ultra Fast Schottky Ultra Fast
Recovery Recovery Recovery Recovery
20V All of 1N5820 All of All of SR502 All of
these these these these
SK32 SR302 1N5823
diodes diodes diodes diodes
MBR320 SB520
are are are are
rated to rated to rated to rated to
30V 30WQ03 1N5821
at least at least at least at least
SK33 MBR330 50WQ03 SR503
50V. 50V. 50V. 50V.
31DQ03 1N5824
1N5822 SB530
40V SK34 SR304 50WQ04 SR504
MBRS340 MBR340 1N5825
30WQ04 MURS320 31DQ04 MUR320 MURS620 SB540 MUR620
50V SK35 30WF10 SR305 50WF10 HER601
or MBRS360 MBR350 50WQ05 SB550
More 30WQ05 31DQ05 50SQ080
Block Diagram
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM2596
LM2596
SNVS124C NOVEMBER 1999REVISED APRIL 2013
www.ti.com
APPLICATION INFORMATION
Table 7. PIN DESCRIPTIONS
Name Description
This is the positive input supply for the IC switching regulator. A suitable input bypass
+VIN capacitor must be present at this pin to minimize voltage transients and to supply the
switching currents needed by the regulator.
Ground Circuit ground.
Internal switch. The voltage at this pin switches between (+VIN VSAT) and approximately
Output 0.5V, with a duty cycle of approximately VOUT/VIN. To minimize coupling to sensitive
circuitry, the PC board copper area connected to this pin should be kept to a minimum.
Feedback Senses the regulated output voltage to complete the feedback loop.
Allows the switching regulator circuit to be shut down using logic level signals thus dropping
the total input supply current to approximately 80 μA. Pulling this pin below a threshold
voltage of approximately 1.3V turns the regulator on, and pulling this pin above 1.3V (up to a
ON /OFF maximum of 25V) shuts the regulator down. If this shutdown feature is not needed, the ON
/OFF pin can be wired to the ground pin or it can be left open, in either case the regulator will
be in the ON condition.
EXTERNAL COMPONENTS
INPUT CAPACITOR
CIN A low ESR aluminum or tantalum bypass capacitor is needed between the input pin and ground pin. It
must be located near the regulator using short leads. This capacitor prevents large voltage transients from
appearing at the input, and provides the instantaneous current needed each time the switch turns on.
The important parameters for the Input capacitor are the voltage rating and the RMS current rating. Because of
the relatively high RMS currents flowing in a buck regulator's input capacitor, this capacitor should be chosen for
its RMS current rating rather than its capacitance or voltage ratings, although the capacitance value and voltage
rating are directly related to the RMS current rating.
The RMS current rating of a capacitor could be viewed as a capacitor's power rating. The RMS current flowing
through the capacitors internal ESR produces power which causes the internal temperature of the capacitor to
rise. The RMS current rating of a capacitor is determined by the amount of current required to raise the internal
temperature approximately 10°C above an ambient temperature of 105°C. The ability of the capacitor to dissipate
this heat to the surrounding air will determine the amount of current the capacitor can safely sustain. Capacitors
that are physically large and have a large surface area will typically have higher RMS current ratings. For a given
capacitor value, a higher voltage electrolytic capacitor will be physically larger than a lower voltage capacitor, and
thus be able to dissipate more heat to the surrounding air, and therefore will have a higher RMS current rating.
The consequences of operating an electrolytic capacitor above the RMS current rating is a shortened operating
life. The higher temperature speeds up the evaporation of the capacitor's electrolyte, resulting in eventual failure.
Selecting an input capacitor requires consulting the manufacturers data sheet for maximum allowable RMS ripple
current. For a maximum ambient temperature of 40°C, a general guideline would be to select a capacitor with a
ripple current rating of approximately 50% of the DC load current. For ambient temperatures up to 70°C, a
current rating of 75% of the DC load current would be a good choice for a conservative design. The capacitor
voltage rating must be at least 1.25 times greater than the maximum input voltage, and often a much higher
voltage capacitor is needed to satisfy the RMS current requirements.
A graph shown in Figure 25 shows the relationship between an electrolytic capacitor value, its voltage rating, and
the RMS current it is rated for. These curves were obtained from the Nichicon “PL” series of low ESR, high
reliability electrolytic capacitors designed for switching regulator applications. Other capacitor manufacturers offer
similar types of capacitors, but always check the capacitor data sheet.
“Standard” electrolytic capacitors typically have much higher ESR numbers, lower RMS current ratings and
typically have a shorter operating lifetime.
18 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2596
LM2596
www.ti.com
SNVS124C NOVEMBER 1999REVISED APRIL 2013
Because of their small size and excellent performance, surface mount solid tantalum capacitors are often used
for input bypassing, but several precautions must be observed. A small percentage of solid tantalum capacitors
can short if the inrush current rating is exceeded. This can happen at turn on when the input voltage is suddenly
applied, and of course, higher input voltages produce higher inrush currents. Several capacitor manufacturers do
a 100% surge current testing on their products to minimize this potential problem. If high turn on currents are
expected, it may be necessary to limit this current by adding either some resistance or inductance before the
tantalum capacitor, or select a higher voltage capacitor. As with aluminum electrolytic capacitors, the RMS ripple
current rating must be sized to the load current.
FEEDFORWARD CAPACITOR
(Adjustable Output Voltage Version)
CFF A Feedforward Capacitor CFF, shown across R2 in Figure 20 is used when the ouput voltage is greater
than 10V or when COUT has a very low ESR. This capacitor adds lead compensation to the feedback loop and
increases the phase margin for better loop stability. For CFF selection, see the Design Procedure section.
Figure 25. RMS Current Ratings for Low ESR Electrolytic Capacitors (Typical)
OUTPUT CAPACITOR
COUT An output capacitor is required to filter the output and provide regulator loop stability. Low impedance or
low ESR Electrolytic or solid tantalum capacitors designed for switching regulator applications must be used.
When selecting an output capacitor, the important capacitor parameters are; the 100 kHz Equivalent Series
Resistance (ESR), the RMS ripple current rating, voltage rating, and capacitance value. For the output capacitor,
the ESR value is the most important parameter.
The output capacitor requires an ESR value that has an upper and lower limit. For low output ripple voltage, a
low ESR value is needed. This value is determined by the maximum allowable output ripple voltage, typically 1%
to 2% of the output voltage. But if the selected capacitor's ESR is extremely low, there is a possibility of an
unstable feedback loop, resulting in an oscillation at the output. Using the capacitors listed in the tables, or
similar types, will provide design solutions under all conditions.
If very low output ripple voltage (less than 15 mV) is required, refer to the section on OUTPUT VOLTAGE
RIPPLE AND TRANSIENTS for a post ripple filter.
An aluminum electrolytic capacitor's ESR value is related to the capacitance value and its voltage rating. In most
cases, higher voltage electrolytic capacitors have lower ESR values (see Figure 26 ). Often, capacitors with
much higher voltage ratings may be needed to provide the low ESR values required for low output ripple voltage.
The output capacitor for many different switcher designs often can be satisfied with only three or four different
capacitor values and several different voltage ratings. See the quick design component selection tables in
Table 1 and 4for typical capacitor values, voltage ratings, and manufacturers capacitor types.
Electrolytic capacitors are not recommended for temperatures below 25°C. The ESR rises dramatically at cold
temperatures and typically rises 3X @ 25°C and as much as 10X at 40°C. See curve shown in Figure 27.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LM2596
LM2596
SNVS124C NOVEMBER 1999REVISED APRIL 2013
www.ti.com
Solid tantalum capacitors have a much better ESR spec for cold temperatures and are recommended for
temperatures below 25°C.
Figure 26. Capacitor ESR vs Capacitor Voltage Rating (Typical Low ESR Electrolytic Capacitor)
CATCH DIODE
Buck regulators require a diode to provide a return path for the inductor current when the switch turns off. This
must be a fast diode and must be located close to the LM2596 using short leads and short printed circuit traces.
Because of their very fast switching speed and low forward voltage drop, Schottky diodes provide the best
performance, especially in low output voltage applications (5V and lower). Ultra-fast recovery, or High-Efficiency
rectifiers are also a good choice, but some types with an abrupt turnoff characteristic may cause instability or
EMI problems. Ultra-fast recovery diodes typically have reverse recovery times of 50 ns or less. Rectifiers such
as the 1N5400 series are much too slow and should not be used.
Figure 27. Capacitor ESR Change vs Temperature
INDUCTOR SELECTION
All switching regulators have two basic modes of operation; continuous and discontinuous. The difference
between the two types relates to the inductor current, whether it is flowing continuously, or if it drops to zero for a
period of time in the normal switching cycle. Each mode has distinctively different operating characteristics,
which can affect the regulators performance and requirements. Most switcher designs will operate in the
discontinuous mode when the load current is low.
The LM2596 (or any of the Simple Switcher family) can be used for both continuous or discontinuous modes of
operation.
20 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2596
LM2596
www.ti.com
SNVS124C NOVEMBER 1999REVISED APRIL 2013
In many cases the preferred mode of operation is the continuous mode. It offers greater output power, lower
peak switch, inductor and diode currents, and can have lower output ripple voltage. But it does require larger
inductor values to keep the inductor current flowing continuously, especially at low output load currents and/or
high input voltages.
To simplify the inductor selection process, an inductor selection guide (nomograph) was designed (see Figure 21
through 8). This guide assumes that the regulator is operating in the continuous mode, and selects an inductor
that will allow a peak-to-peak inductor ripple current to be a certain percentage of the maximum design load
current. This peak-to-peak inductor ripple current percentage is not fixed, but is allowed to change as different
design load currents are selected. (See Figure 28.)
Figure 28. (ΔIIND) Peak-to-Peak Inductor
Ripple Current (as a Percentage of the Load Current)
vs Load Current
By allowing the percentage of inductor ripple current to increase for low load currents, the inductor value and size
can be kept relatively low.
When operating in the continuous mode, the inductor current waveform ranges from a triangular to a sawtooth
type of waveform (depending on the input voltage), with the average value of this current waveform equal to the
DC output load current.
Inductors are available in different styles such as pot core, toroid, E-core, bobbin core, etc., as well as different
core materials, such as ferrites and powdered iron. The least expensive, the bobbin, rod or stick core, consists of
wire wound on a ferrite bobbin. This type of construction makes for an inexpensive inductor, but since the
magnetic flux is not completely contained within the core, it generates more Electro-Magnetic Interference (EMl).
This magnetic flux can induce voltages into nearby printed circuit traces, thus causing problems with both the
switching regulator operation and nearby sensitive circuitry, and can give incorrect scope readings because of
induced voltages in the scope probe. Also see section on OPEN CORE INDUCTORS.
When multiple switching regulators are located on the same PC board, open core magnetics can cause
interference between two or more of the regulator circuits, especially at high currents. A torroid or E-core inductor
(closed magnetic structure) should be used in these situations.
The inductors listed in the selection chart include ferrite E-core construction for Schott, ferrite bobbin core for
Renco and Coilcraft, and powdered iron toroid for Pulse Engineering.
Exceeding an inductor's maximum current rating may cause the inductor to overheat because of the copper wire
losses, or the core may saturate. If the inductor begins to saturate, the inductance decreases rapidly and the
inductor begins to look mainly resistive (the DC resistance of the winding). This can cause the switch current to
rise very rapidly and force the switch into a cycle-by-cycle current limit, thus reducing the DC output load current.
This can also result in overheating of the inductor and/or the LM2596. Different inductor types have different
saturation characteristics, and this should be kept in mind when selecting an inductor.
The inductor manufacturer's data sheets include current and energy limits to avoid inductor saturation.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: LM2596
LM2596
SNVS124C NOVEMBER 1999REVISED APRIL 2013
www.ti.com
DISCONTINUOUS MODE OPERATION
The selection guide chooses inductor values suitable for continuous mode operation, but for low current
applications and/or high input voltages, a discontinuous mode design may be a better choice. It would use an
inductor that would be physically smaller, and would need only one half to one third the inductance value needed
for a continuous mode design. The peak switch and inductor currents will be higher in a discontinuous design,
but at these low load currents (1A and below), the maximum switch current will still be less than the switch
current limit.
Discontinuous operation can have voltage waveforms that are considerable different than a continuous design.
The output pin (switch) waveform can have some damped sinusoidal ringing present. (See Typical Performance
Characteristics photo titled Discontinuous Mode Switching Waveforms) This ringing is normal for discontinuous
operation, and is not caused by feedback loop instabilities. In discontinuous operation, there is a period of time
where neither the switch or the diode are conducting, and the inductor current has dropped to zero. During this
time, a small amount of energy can circulate between the inductor and the switch/diode parasitic capacitance
causing this characteristic ringing. Normally this ringing is not a problem, unless the amplitude becomes great
enough to exceed the input voltage, and even then, there is very little energy present to cause damage.
Different inductor types and/or core materials produce different amounts of this characteristic ringing. Ferrite core
inductors have very little core loss and therefore produce the most ringing. The higher core loss of powdered iron
inductors produce less ringing. If desired, a series RC could be placed in parallel with the inductor to dampen the
ringing. The computer aided design software Switchers Made Simple (version 4.3) will provide all component
values for continuous and discontinuous modes of operation.
Figure 29. Post Ripple Filter Waveform
OUTPUT VOLTAGE RIPPLE AND TRANSIENTS
The output voltage of a switching power supply operating in the continuous mode will contain a sawtooth ripple
voltage at the switcher frequency, and may also contain short voltage spikes at the peaks of the sawtooth
waveform.
The output ripple voltage is a function of the inductor sawtooth ripple current and the ESR of the output
capacitor. A typical output ripple voltage can range from approximately 0.5% to 3% of the output voltage. To
obtain low ripple voltage, the ESR of the output capacitor must be low, however, caution must be exercised when
using extremely low ESR capacitors because they can affect the loop stability, resulting in oscillation problems. If
very low output ripple voltage is needed (less than 20 mV), a post ripple filter is recommended. (See Figure 20.)
The inductance required is typically between 1 μH and 5 μH, with low DC resistance, to maintain good load
regulation. A low ESR output filter capacitor is also required to assure good dynamic load response and ripple
reduction. The ESR of this capacitor may be as low as desired, because it is out of the regulator feedback loop.
The photo shown in Figure 29 shows a typical output ripple voltage, with and without a post ripple filter.
22 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2596
LM2596
www.ti.com
SNVS124C NOVEMBER 1999REVISED APRIL 2013
When observing output ripple with a scope, it is essential that a short, low inductance scope probe ground
connection be used. Most scope probe manufacturers provide a special probe terminator which is soldered onto
the regulator board, preferable at the output capacitor. This provides a very short scope ground thus eliminating
the problems associated with the 3 inch ground lead normally provided with the probe, and provides a much
cleaner and more accurate picture of the ripple voltage waveform.
The voltage spikes are caused by the fast switching action of the output switch and the diode, and the parasitic
inductance of the output filter capacitor, and its associated wiring. To minimize these voltage spikes, the output
capacitor should be designed for switching regulator applications, and the lead lengths must be kept very short.
Wiring inductance, stray capacitance, as well as the scope probe used to evaluate these transients, all contribute
to the amplitude of these spikes.
When a switching regulator is operating in the continuous mode, the inductor current waveform ranges from a
triangular to a sawtooth type of waveform (depending on the input voltage). For a given input and output voltage,
the peak-to-peak amplitude of this inductor current waveform remains constant. As the load current increases or
decreases, the entire sawtooth current waveform also rises and falls. The average value (or the center) of this
current waveform is equal to the DC load current.
If the load current drops to a low enough level, the bottom of the sawtooth current waveform will reach zero, and
the switcher will smoothly change from a continuous to a discontinuous mode of operation. Most switcher
designs (irregardless how large the inductor value is) will be forced to run discontinuous if the output is lightly
loaded. This is a perfectly acceptable mode of operation.
Figure 30. Peak-to-Peak Inductor
Ripple Current vs Load Current
In a switching regulator design, knowing the value of the peak-to-peak inductor ripple current (ΔIIND) can be
useful for determining a number of other circuit parameters. Parameters such as, peak inductor or peak switch
current, minimum load current before the circuit becomes discontinuous, output ripple voltage and output
capacitor ESR can all be calculated from the peak-to-peak ΔIIND. When the inductor nomographs shown in
Figure 21 through 8are used to select an inductor value, the peak-to-peak inductor ripple current can
immediately be determined. The curve shown in Figure 30 shows the range of (ΔIIND) that can be expected for
different load currents. The curve also shows how the peak-to-peak inductor ripple current (ΔIIND) changes as
you go from the lower border to the upper border (for a given load current) within an inductance region. The
upper border represents a higher input voltage, while the lower border represents a lower input voltage (see
Inductor Selection Guides section).
These curves are only correct for continuous mode operation, and only if the inductor selection guides are used
to select the inductor value
Consider the following example:
VOUT = 5V, maximum load current of 2.5A
VIN = 12V, nominal, varying between 10V and 16V.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 23
Product Folder Links: LM2596
LM2596
SNVS124C NOVEMBER 1999REVISED APRIL 2013
www.ti.com
The selection guide in Figure 22 shows that the vertical line for a 2.5A load current, and the horizontal line for the
12V input voltage intersect approximately midway between the upper and lower borders of the 33 μH inductance
region. A 33 μH inductor will allow a peak-to-peak inductor current (ΔIIND) to flow that will be a percentage of the
maximum load current. Referring to Figure 30, follow the 2.5A line approximately midway into the inductance
region, and read the peak-to-peak inductor ripple current (ΔIIND) on the left hand axis (approximately 620 mA p-
p).
As the input voltage increases to 16V, it approaches the upper border of the inductance region, and the inductor
ripple current increases. Referring to the curve in Figure 30, it can be seen that for a load current of 2.5A, the
peak-to-peak inductor ripple current (ΔIIND) is 620 mA with 12V in, and can range from 740 mA at the upper
border (16V in) to 500 mA at the lower border (10V in).
Once the ΔIIND value is known, the following formulas can be used to calculate additional information about the
switching regulator circuit.
1. Peak Inductor or peak switch current
2. Minimum load current before the circuit becomes discontinuous
3. Output Ripple Voltage = (ΔIIND(ESR of COUT) = 0.62A×0.1Ω= 62 mV p-p
4. added for line break
OPEN CORE INDUCTORS
Another possible source of increased output ripple voltage or unstable operation is from an open core inductor.
Ferrite bobbin or stick inductors have magnetic lines of flux flowing through the air from one end of the bobbin to
the other end. These magnetic lines of flux will induce a voltage into any wire or PC board copper trace that
comes within the inductor's magnetic field. The strength of the magnetic field, the orientation and location of the
PC copper trace to the magnetic field, and the distance between the copper trace and the inductor, determine
the amount of voltage generated in the copper trace. Another way of looking at this inductive coupling is to
consider the PC board copper trace as one turn of a transformer (secondary) with the inductor winding as the
primary. Many millivolts can be generated in a copper trace located near an open core inductor which can cause
stability problems or high output ripple voltage problems.
If unstable operation is seen, and an open core inductor is used, it's possible that the location of the inductor with
respect to other PC traces may be the problem. To determine if this is the problem, temporarily raise the inductor
away from the board by several inches and then check circuit operation. If the circuit now operates correctly,
then the magnetic flux from the open core inductor is causing the problem. Substituting a closed core inductor
such as a torroid or E-core will correct the problem, or re-arranging the PC layout may be necessary. Magnetic
flux cutting the IC device ground trace, feedback trace, or the positive or negative traces of the output capacitor
should be minimized.
Sometimes, locating a trace directly beneath a bobbin in- ductor will provide good results, provided it is exactly in
the center of the inductor (because the induced voltages cancel themselves out), but if it is off center one
direction or the other, then problems could arise. If flux problems are present, even the direction of the inductor
winding can make a difference in some circuits.
This discussion on open core inductors is not to frighten the user, but to alert the user on what kind of problems
to watch out for when using them. Open core bobbin or “stick” inductors are an inexpensive, simple way of
making a compact efficient inductor, and they are used by the millions in many different applications.
24 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2596
LM2596
www.ti.com
SNVS124C NOVEMBER 1999REVISED APRIL 2013
THERMAL CONSIDERATIONS
The LM2596 is available in two packages, a 5-pin TO-220 (T) and a 5-pin surface mount TO-263 (S).
The TO-220 package needs a heat sink under most conditions. The size of the heatsink depends on the input
voltage, the output voltage, the load current and the ambient temperature. The curves in Figure 31 show the
LM2596T junction temperature rises above ambient temperature for a 3A load and different input and output
voltages. The data for these curves was taken with the LM2596T (TO-220 package) operating as a buck
switching regulator in an ambient temperature of 25°C (still air). These temperature rise numbers are all
approximate and there are many factors that can affect these temperatures. Higher ambient temperatures require
more heat sinking.
The TO-263 surface mount package tab is designed to be soldered to the copper on a printed circuit board. The
copper and the board are the heat sink for this package and the other heat producing components, such as the
catch diode and inductor. The PC board copper area that the package is soldered to should be at least 0.4 in2,
and ideally should have 2 or more square inches of 2 oz. (0.0028 in.) copper. Additional copper area improves
the thermal characteristics, but with copper areas greater than approximately 6 in2, only small improvements in
heat dissipation are realized. If further thermal improvements are needed, double sided, multilayer PC board with
large copper areas and/or airflow are recommended.
The curves shown in Figure 32 show the LM2596S (TO-263 package) junction temperature rise above ambient
temperature with a 2A load for various input and output voltages. This data was taken with the circuit operating
as a buck switching regulator with all components mounted on a PC board to simulate the junction temperature
under actual operating conditions. This curve can be used for a quick check for the approximate junction
temperature for various conditions, but be aware that there are many factors that can affect the junction
temperature. When load currents higher than 2A are used, double sided or multilayer PC boards with large
copper areas and/or airflow might be needed, especially for high ambient temperatures and high output voltages.
For the best thermal performance, wide copper traces and generous amounts of printed circuit board copper
should be used in the board layout. (One exception to this is the output (switch) pin, which should not have large
areas of copper.) Large areas of copper provide the best transfer of heat (lower thermal resistance) to the
surrounding air, and moving air lowers the thermal resistance even further.
Package thermal resistance and junction temperature rise numbers are all approximate, and there are many
factors that will affect these numbers. Some of these factors include board size, shape, thickness, position,
location, and even board temperature. Other factors are, trace width, total printed circuit copper area, copper
thickness, single- or double-sided, multilayer board and the amount of solder on the board. The effectiveness of
the PC board to dissipate heat also depends on the size, quantity and spacing of other components on the
board, as well as whether the surrounding air is still or moving. Furthermore, some of these components such as
the catch diode will add heat to the PC board and the heat can vary as the input voltage changes. For the
inductor, depending on the physical size, type of core material and the DC resistance, it could either act as a
heat sink taking heat away from the board, or it could add heat to the board.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 25
Product Folder Links: LM2596
LM2596
SNVS124C NOVEMBER 1999REVISED APRIL 2013
www.ti.com
Circuit Data for Temperature Rise Curve
TO-220 Package (T)
Capacitors Through hole electrolytic
Inductor Through hole, Renco
Diode Through hole, 5A 40V, Schottky
PC board 3 square inches single sided 2 oz. copper (0.0028)
Figure 31. Junction Temperature Rise, TO-220
Circuit Data for Temperature Rise Curve
TO-263 Package (S)
Capacitors Surface mount tantalum, molded “D” size
Inductor Surface mount, Pulse Engineering, 68 μH
Diode Surface mount, 5A 40V, Schottky
PC board 9 square inches single sided 2 oz. copper (0.0028)
Figure 32. Junction Temperature Rise, TO-263
26 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2596
LM2596
www.ti.com
SNVS124C NOVEMBER 1999REVISED APRIL 2013
Figure 33. Delayed Startup
Figure 34. Undervoltage Lockout
for Buck Regulator
DELAYED STARTUP
The circuit in Figure 33 uses the the ON /OFF pin to provide a time delay between the time the input voltage is
applied and the time the output voltage comes up (only the circuitry pertaining to the delayed start up is shown).
As the input voltage rises, the charging of capacitor C1 pulls the ON /OFF pin high, keeping the regulator off.
Once the input voltage reaches its final value and the capacitor stops charging, and resistor R2pulls the ON
/OFF pin low, thus allowing the circuit to start switching. Resistor R1is included to limit the maximum voltage
applied to the ON /OFF pin (maximum of 25V), reduces power supply noise sensitivity, and also limits the
capacitor, C1, discharge current. When high input ripple voltage exists, avoid long delay time, because this ripple
can be coupled into the ON /OFF pin and cause problems.
This delayed startup feature is useful in situations where the input power source is limited in the amount of
current it can deliver. It allows the input voltage to rise to a higher voltage before the regulator starts operating.
Buck regulators require less input current at higher input voltages.
UNDERVOLTAGE LOCKOUT
Some applications require the regulator to remain off until the input voltage reaches a predetermined voltage. An
undervoltage lockout feature applied to a buck regulator is shown in Figure 34, while Figure 35 and Figure 36
applies the same feature to an inverting circuit. The circuit in Figure 35 features a constant threshold voltage for
turn on and turn off (zener voltage plus approximately one volt). If hysteresis is needed, the circuit in Figure 36
has a turn ON voltage which is different than the turn OFF voltage. The amount of hysteresis is approximately
equal to the value of the output voltage. If zener voltages greater than 25V are used, an additional 47 kΩresistor
is needed from the ON /OFF pin to the ground pin to stay within the 25V maximum limit of the ON /OFF pin.
INVERTING REGULATOR
The circuit in Figure 37 converts a positive input voltage to a negative output voltage with a common ground. The
circuit operates by bootstrapping the regulator's ground pin to the negative output voltage, then grounding the
feedback pin, the regulator senses the inverted output voltage and regulates it.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 27
Product Folder Links: LM2596
LM2596
SNVS124C NOVEMBER 1999REVISED APRIL 2013
www.ti.com
This circuit has an ON/OFF threshold of approximately 13V.
Figure 35. Undervoltage Lockout
for Inverting Regulator
This example uses the LM2596-5.0 to generate a 5V output, but other output voltages are possible by selecting
other output voltage versions, including the adjustable version. Since this regulator topology can produce an
output voltage that is either greater than or less than the input voltage, the maximum output current greatly
depends on both the input and output voltage. The curve shown in Figure 38 provides a guide as to the amount
of output load current possible for the different input and output voltage conditions.
The maximum voltage appearing across the regulator is the absolute sum of the input and output voltage, and
this must be limited to a maximum of 40V. For example, when converting +20V to 12V, the regulator would see
32V between the input pin and ground pin. The LM2596 has a maximum input voltage spec of 40V.
Additional diodes are required in this regulator configuration. Diode D1 is used to isolate input voltage ripple or
noise from coupling through the CIN capacitor to the output, under light or no load conditions. Also, this diode
isolation changes the topology to closley resemble a buck configuration thus providing good closed loop stability.
A Schottky diode is recommended for low input voltages, (because of its lower voltage drop) but for higher input
voltages, a fast recovery diode could be used.
Without diode D3, when the input voltage is first applied, the charging current of CIN can pull the output positive
by several volts for a short period of time. Adding D3 prevents the output from going positive by more than a
diode voltage.
This circuit has hysteresis
Regulator starts switching at VIN = 13V
Regulator stops switching at VIN = 8V
Figure 36. Undervoltage Lockout with Hysteresis for Inverting Regulator
28 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2596
LM2596
www.ti.com
SNVS124C NOVEMBER 1999REVISED APRIL 2013
CIN —68 μF/25V Tant. Sprague 595D
470 μF/50V Elec. Panasonic HFQ
COUT —47 μF/20V Tant. Sprague 595D
220 μF/25V Elec. Panasonic HFQ
Figure 37. Inverting 5V Regulator with Delayed Startup
Figure 38. Inverting Regulator Typical Load Current
Because of differences in the operation of the inverting regulator, the standard design procedure is not used to
select the inductor value. In the majority of designs, a 33 μH, 3.5A inductor is the best choice. Capacitor
selection can also be narrowed down to just a few values. Using the values shown in Figure 37 will provide good
results in the majority of inverting designs.
This type of inverting regulator can require relatively large amounts of input current when starting up, even with
light loads. Input currents as high as the LM2596 current limit (approx 4.5A) are needed for at least 2 ms or
more, until the output reaches its nominal output voltage. The actual time depends on the output voltage and the
size of the output capacitor. Input power sources that are current limited or sources that can not deliver these
currents without getting loaded down, may not work correctly. Because of the relatively high startup currents
required by the inverting topology, the delayed startup feature (C1, R1and R2) shown in Figure 37 is
recommended. By delaying the regulator startup, the input capacitor is allowed to charge up to a higher voltage
before the switcher begins operating. A portion of the high input current needed for startup is now supplied by the
input capacitor (CIN). For severe start up conditions, the input capacitor can be made much larger than normal.
INVERTING REGULATOR SHUTDOWN METHODS
To use the ON /OFF pin in a standard buck configuration is simple, pull it below 1.3V (@25°C, referenced to
ground) to turn regulator ON, pull it above 1.3V to shut the regulator OFF. With the inverting configuration, some
level shifting is required, because the ground pin of the regulator is no longer at ground, but is now setting at the
negative output voltage level. Two different shutdown methods for inverting regulators are shown in Figure 39
and Figure 40.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 29
Product Folder Links: LM2596
LM2596
SNVS124C NOVEMBER 1999REVISED APRIL 2013
www.ti.com
Figure 39. Inverting Regulator Ground Referenced Shutdown
Figure 40. Inverting Regulator Ground Referenced Shutdown using Opto Device
TYPICAL THROUGH HOLE PC BOARD LAYOUT, FIXED OUTPUT (1X SIZE), DOUBLE SIDED
CIN—470 μF, 50V, Aluminum Electrolytic Panasonic, “HFQ Series”
COUT—330 μF, 35V, Aluminum Electrolytic Panasonic, “HFQ Series”
D1—5A, 40V Schottky Rectifier, 1N5825
L1—47 μH, L39, Renco, Through Hole
Thermalloy Heat Sink #7020
30 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2596
LM2596
www.ti.com
SNVS124C NOVEMBER 1999REVISED APRIL 2013
TYPICAL THROUGH HOLE PC BOARD LAYOUT, ADJUSTABLE OUTPUT (1X SIZE), DOUBLE SIDED
CIN—470 μF, 50V, Aluminum Electrolytic Panasonic, “HFQ Series”
COUT—220 μF, 35V Aluminum Electrolytic Panasonic, “HFQ Series”
D1—5A, 40V Schottky Rectifier, 1N5825
L1—47 μH, L39, Renco, Through Hole
R1—1 kΩ, 1%
R2—Use formula in Design Procedure
CFF—See Table 2.
Thermalloy Heat Sink #7020
Figure 41. PC Board Layout
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 31
Product Folder Links: LM2596
LM2596
SNVS124C NOVEMBER 1999REVISED APRIL 2013
www.ti.com
REVISION HISTORY
Changes from Revision B (April 2013) to Revision C Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 31
32 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2596
PACKAGE OPTION ADDENDUM
www.ti.com 1-Nov-2013
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM2596S-12/NOPB ACTIVE DDPAK/
TO-263 KTT 5 45 Pb-Free (RoHS
Exempt) CU SN Level-3-245C-168 HR LM2596S
-12 P+
LM2596S-3.3 NRND DDPAK/
TO-263 KTT 5 45 TBD Call TI Call TI LM2596S
-3.3 P+
LM2596S-3.3/NOPB ACTIVE DDPAK/
TO-263 KTT 5 45 Pb-Free (RoHS
Exempt) CU SN Level-3-245C-168 HR LM2596S
-3.3 P+
LM2596S-5.0 NRND DDPAK/
TO-263 KTT 5 45 TBD Call TI Call TI LM2596S
-5.0 P+
LM2596S-5.0/NOPB ACTIVE DDPAK/
TO-263 KTT 5 45 Pb-Free (RoHS
Exempt) CU SN Level-3-245C-168 HR LM2596S
-5.0 P+
LM2596S-ADJ/NOPB ACTIVE DDPAK/
TO-263 KTT 5 45 Pb-Free (RoHS
Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM2596S
-ADJ P+
LM2596SX-12/NOPB ACTIVE DDPAK/
TO-263 KTT 5 500 Pb-Free (RoHS
Exempt) CU SN Level-3-245C-168 HR LM2596S
-12 P+
LM2596SX-3.3 NRND DDPAK/
TO-263 KTT 5 500 TBD Call TI Call TI LM2596S
-3.3 P+
LM2596SX-3.3/NOPB ACTIVE DDPAK/
TO-263 KTT 5 500 Pb-Free (RoHS
Exempt) CU SN Level-3-245C-168 HR LM2596S
-3.3 P+
LM2596SX-5.0/NOPB ACTIVE DDPAK/
TO-263 KTT 5 500 Pb-Free (RoHS
Exempt) CU SN Level-3-245C-168 HR LM2596S
-5.0 P+
LM2596SX-ADJ NRND DDPAK/
TO-263 KTT 5 500 TBD Call TI Call TI -40 to 125 LM2596S
-ADJ P+
LM2596SX-ADJ/NOPB ACTIVE DDPAK/
TO-263 KTT 5 500 Pb-Free (RoHS
Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM2596S
-ADJ P+
LM2596T-12 NRND TO-220 NDH 5 45 TBD Call TI Call TI LM2596T
-12 P+
LM2596T-12/LF03 ACTIVE TO-220 NDH 5 45 Green (RoHS
& no Sb/Br) CU SN Level-1-NA-UNLIM LM2596T
-12 P+
LM2596T-12/NOPB ACTIVE TO-220 NDH 5 45 Green (RoHS
& no Sb/Br) CU SN Level-1-NA-UNLIM LM2596T
-12 P+
LM2596T-3.3 NRND TO-220 NDH 5 45 TBD Call TI Call TI LM2596T
-3.3 P+
LM2596T-3.3/LF03 ACTIVE TO-220 NDH 5 45 Green (RoHS
& no Sb/Br) CU SN Level-1-NA-UNLIM LM2596T
-3.3 P+
PACKAGE OPTION ADDENDUM
www.ti.com 1-Nov-2013
Addendum-Page 2
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM2596T-3.3/NOPB ACTIVE TO-220 NDH 5 45 Green (RoHS
& no Sb/Br) CU SN Level-1-NA-UNLIM LM2596T
-3.3 P+
LM2596T-5.0 NRND TO-220 NDH 5 45 TBD Call TI Call TI LM2596T
-5.0 P+
LM2596T-5.0/LF03 ACTIVE TO-220 NDH 5 45 Green (RoHS
& no Sb/Br) CU SN Level-1-NA-UNLIM LM2596T
-5.0 P+
LM2596T-5.0/NOPB ACTIVE TO-220 NDH 5 45 Green (RoHS
& no Sb/Br) CU SN Level-1-NA-UNLIM LM2596T
-5.0 P+
LM2596T-ADJ NRND TO-220 NDH 5 45 TBD Call TI Call TI -40 to 125 LM2596T
-ADJ P+
LM2596T-ADJ/LB05 NRND TO-220 NEB 5 45 TBD Call TI Call TI LM2596T
-ADJ P+
LM2596T-ADJ/LF02 ACTIVE TO-220 NEB 5 45 Green (RoHS
& no Sb/Br) CU SN Level-1-NA-UNLIM LM2596T
-ADJ P+
LM2596T-ADJ/NOPB ACTIVE TO-220 NDH 5 45 Green (RoHS
& no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 125 LM2596T
-ADJ P+
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
PACKAGE OPTION ADDENDUM
www.ti.com 1-Nov-2013
Addendum-Page 3
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM2596SX-12/NOPB DDPAK/
TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
LM2596SX-3.3 DDPAK/
TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
LM2596SX-3.3/NOPB DDPAK/
TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
LM2596SX-5.0/NOPB DDPAK/
TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
LM2596SX-ADJ DDPAK/
TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
LM2596SX-ADJ/NOPB DDPAK/
TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
PACKAGE MATERIALS INFORMATION
www.ti.com 23-Sep-2013
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM2596SX-12/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0
LM2596SX-3.3 DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0
LM2596SX-3.3/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0
LM2596SX-5.0/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0
LM2596SX-ADJ DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0
LM2596SX-ADJ/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0
PACKAGE MATERIALS INFORMATION
www.ti.com 23-Sep-2013
Pack Materials-Page 2
MECHANICAL DATA
NDH0005D
www.ti.com
MECHANICAL DATA
KTT0005B
www.ti.com
BOTTOM SIDE OF PACKAGE
TS5B (Rev D)
MECHANICAL DATA
NEB0005B
www.ti.com
MECHANICAL DATA
NEB0005E
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated