DS1371U/C01 - Maxim Integrated Products, Inc.

1 of 15 031902

FEATURES

§ Memory maps into any standard byte-wide

data bus.

§ Eliminates CPU “bit-banging” by internally

generating all 1-Wire® timing and control

signals.

§ Generates interrupts to provide for more

efficient programming.

§ Search ROM Accelerator relieves CPU from

any single bit operations on the 1-Wire Bus.

§ Supports Overdrive mode and slave

interrupts.

§ Capable of running off any system clock from

3.2MHz to 128MHz.

§ Small size: all digital design, only 1500 gates.

§ Available in both Verilog and VHDL.

§ Applications include any circuit containing a

1-Wire communication bus.

Customer ASIC

DESCRIPTION

As more 1-Wire devices become available, more and more users have to deal with the demands of

generating 1-Wire signals to communicate to them. This usually requires “bit-banging” a port pin on a

microprocessor, and having the microprocessor perform the timing functions required for the 1-Wire

protocol. While 1-Wire transmission can be interrupted mid-byte, it cannot be interrupted during the

“low” time of a bit time slot; this means that a CPU will be idled for up to 60 microseconds for each bit

sent and at least 480 microseconds when generating a 1-Wire reset. The 1-Wire Master helps users handle

communication to 1-Wire devices in their system without tying up valuable CPU cycles. Integrated into a

user’s ASIC as a 1-Wire port, the core is available in both VHDL and Verilog code and uses very little

chip area (1492 gates plus 1 bond pad for the Verilog version).

This circuit is designed to be memory mapped into the user’s system and provides complete control of the

1-Wire bus through 8 bit commands. The host CPU loads commands, reads and writes data, and sets

interrupt control through five individual registers. All of the timing and control of the 1-Wire bus are

generated within. The host merely needs to load a command or data and then may go on about its

business. When bus activity has generated a response that the CPU needs to receive, the 1-Wire Master

sets a status bit and, if enabled, generates an interrupt to the CPU. In addition to write and read

simplification, the 1-Wire Master also provides a Search ROM Accelerator function relieving the CPU

from having to perform any single-bit operations on the 1-Wire bus.

DS1WM

Synthesizable 1-Wire Bus Maste

www.maxim-ic.com

1-Wire

Master

1-Wire

Bus

Internal

Data Bus

Interrupt

1-Wire is a registered trademark of Dallas Semiconductor.

DS1WM

2 of 15

The operation of the 1-Wire bus is described in detail in the Book of iButton Standards [1]; therefore, the

details of that will not be discussed in this document. Each slave device, in general, has its own set of

commands that are described in detail in that device’s data sheet. The user is referred to those documents

for detail on specific slave implementations.

BLOCK DIAGRAM

INTERRUPT REGISTER

INT ENABLE REGISTER

DATA BUS

BUFFER

CONTROL

LOGIC

MASTE

RESET

1-WIRE

TIMING

AND

CONTROL

INTERRUPT

CONTROL

LOGIC

D0-D7

INTR

ADS

CLK CLOCK

DIVIDER

COMMAND REGISTER

TRANSMIT BUFFER

Tx SHIFT REGISTER

Rx SHIFT REGISTER

RECEIVE BUFFER

CLOCK DIV REGISTER

DS1WM

3 of 15

PIN DESCRIPTIONS

The following describes the function of all the block I/O pins. In the following descriptions, 0 represents

logic low and 1 represents logic high.

A0, A1, A2, Register Select: Address signals connected to these three inputs select a register for the CPU

to read from or write to during data transfer. A table of registers and their addresses is shown below.

A2 A1 A0 Register

0 0 0 Command Register (read/write)

0 0 1 Transmit Buffer (write), Receive Buffer (read)

0 1 0 Interrupt Register (read)

0 1 1 Interrupt Enable Register (read/write)

1 0 0 Clock Divisor Register (read/write)

ADS , Address Strobe: The positive edge of an active Address Strobe (ADS ) signal latches the Register

Select (A0, A1, A2) into an internal latch. Provided that setup and hold timings are observed, ADS may

be tied low making the latch transparent.

CLK, Clock Input: This is a (preferably) 50% duty cycle clock that can range from 3.2MHz to 128MHz.

This clock provides the timing for the 1-Wire bus.

D7-D0, Data Bus: This bus comprises eight input/output lines. The bus provides bi-directional

communications between the 1-Wire Master and the CPU. Data, control words, and status information are

transferred via this D7-D0 Data Bus.

DQ, 1-Wire Data Line: This open-drain line is the 1-Wire bi-directional data bus. 1-Wire slave devices

are connected to this pin. This pin must be pulled high by an external resistor, nominally 5KW.

EN , Enable: When EN is low, the 1-Wire Master is enabled; this signal acts as the device chip enable.

This enables communication between the 1-Wire Master and the CPU.

INTR, Interrupt: This line goes to its active state whenever any one of the interrupt types has an active

high condition and is enabled via the Interrupt Enable Register. The INTR signal is reset to an inactive

state when the Interrupt Register is read.

MR, Master Reset: When this input is high, it clears all the registers and the control logic of the 1-Wire

Master, and sets INTR to its default inactive state, which is HIGH.

RD , Read: This pin drives the bus during a read cycle. When the circuit is enabled, the CPU can read

status information or data from the selected register by driving RD low. RD and WR should never be

low simultaneously; if they are, WR takes precedence.

, Write: This pin drives the bus during a write cycle. When WR is low while the circuit is enabled,

the CPU can write control words or data into the selected register. RD and WR should never be low

simultaneously; if they are, WR takes precedence.

DS1WM

4 of 15

OPERATION – CLOCK DIVISOR

All 1-Wire timing patterns are generated using a base clock of 1.0MHz. The 1-Wire Master will generate

this clock frequency internally given an external reference on the CLK pin. The external clock must have

a frequency from 3.2MHz to 128MHz and a 50% duty cycle is preferred. The Clock Divisor Register

controls the internal clock divider and provides the desired reference frequency. This is done in two

stages: first a prescaler divides by 1, 3, 5, or 7, then the remaining circuitry divides by 2, 4, 8, 16, 32,

64,or 128.

Clock Divisor Register

Addr. 04h X X X DIV2 DIV1 DIV0 PRE1 PRE0

MSB LSB

The clock divisor must be configured before communication on the 1-Wire bus can take place. This

based on the CLK reference frequency. For example, the user would write 0x10h to this location when

providing a 15MHz input clock.

Clock Divisor Register Settings for Input Clock Rates

Min CLK

Frequency

(MHz)

Max CLK

Frequency

(MHz)

Divider

Ratio

DIV3 DIV2 DIV1 PRE1 PRE0

>3.2 4.0 4 0 1000

>4.0 5.0 5 0 0010

>5.0 6.0 6 0 0101

>6.0 7.0 7 0 0011

>7.0 8.0 8 0 1100

>8.0 10.0 10 0 0110

>10.0 12.0 12 0 1001

>12.0 14.0 14 0 0111

>14.0 16.0 16 1 0000

>16.0 20.0 20 0 1010

>20.0 24.0 24 0 1101

>24.0 28.0 28 0 1011

>28.0 32.0 32 1 0100

>32.0 40.0 40 0 1110

>40.0 48.0 48 1 0001

>48.0 56.0 56 0 1111

>56.0 64.0 64 1 1000

>64.0 80.0 80 1 0010

>80.0 96.0 96 1 0101

>96.0 112.0 112 1 0011

>112.0 128.0 128 1 1100

DS1WM

5 of 15

OPERATION — TRANSMITTING / RECEIVING DATA

Data sent and received from the 1-Wire Master passes through the transmit/receive buffer location. The 1-

Wire Master is actually double buffered with separate transmit and receive buffers. Writing to this

location connects the Transmit Buffer to the data bus, while reading connects the Receive Buffer to the

data bus.

Transmit Buffer (Write) / Receive Buffer (Read)

Addr. 01h Data7 Data6 Data5 Data4 Data3 Data2 Data1 Data0

MSB LSB

Writing a Byte

To send a byte on the 1-Wire bus, the user writes the desired data to the Transmit Buffer. The data is then

moved to the Transmit Shift Register where it is shifted serially onto the bus LSB first. A new byte of

data can then be written to the Transmit Buffer. As soon as the Transmit Shift Register is empty, the data

will be transferred from the Transmit Buffer and the process repeats. Each of these registers has a flag

that may be used as an interrupt source. The Transmit Buffer Empty (TBE) flag is set when the Transmit

Buffer is empty and ready to accept a new byte. As soon as a byte is written into the Transmit Buffer,

TBE is cleared. The Transmit Shift Register Empty (TEMT) flag is set when the shift register has no data

in it and is ready to accept a new byte. As soon as a byte of data is transferred from the Transmit Buffer,

TEMT is cleared and TBE is set. Remember that proper 1-Wire protocol requires a reset before any bus

communication.

Reading a byte

To read data from a slave device, the device must first be ready to transmit data depending on commands

already received from the CPU. Data is retrieved from the bus in a similar fashion to a write operation.

The host initiates a read by writing to the Transmit Buffer. The data that is then shifted into the Receive

Shift Register is the wired-AND of the written data and the data from the slave device. Therefore, in order

to read a byte from a slave device the host must write 0xFFh. When the Receive Shift Register is full the

data is transferred to the Receive Buffer where it can be accessed by the host. Additional bytes can now

be read by sending 0xFFh again. If the slave device is not ready to transmit, the data received will be

identical to that which was transmitted. The Receive Buffer Register can also generate interrupts. The

Receive Buffer flag (RBF) is set when data is transferred from the Receive Shift Register and cleared

when the host reads the register. If RBF is set, no further transmissions should be made on the 1-Wire bus

or else data may be lost, as the byte in the Receive Buffer will be overwritten by the next received byte.

See the timing diagrams for details of the byte reception operation. Generating a 1-Wire reset on the bus

is covered under Command Operations. Interrupt flags are explained in further detail under Interrupt

Operations. Write and read operations are detailed in the timing diagrams.

DS1WM

6 of 15

OPERATION — COMMANDS

The Command Register determines the DS1WM’s mode of operation and also handles special

transmissions over the bus. From this register the DS1WM can be selected to run in Overdrive mode,

Search ROM Accelerator mode, or standard mode. This register also controls bus resets, 1-Wire Master

resets, and direct reading and writing of the bus.

Command Register (Read/Write)

Addr. 00h OD X RST X DQI DQO SRA 1WR

MSB LSB

OD: Overdrive Bit. This bit selects the communication rate on the 1-Wire bus. Setting this bit to 1 will

allow high-speed communication if all slave devices on the bus support overdrive mode. This bit must be

set to 0 for standard 1-wire communication.

RST: Software Reset. Setting this bit will immediately stop any communication and reset all internal

state machines controlling communication. This command does not reset data in the registers. All register

data will be maintained, however the Interrupt Register may change to reflect the new state of the 1-Wire

Master. This bit must be 0 for normal operation.

DQO: DQ Output. This bit can be used to bypass 1-Wire Master operations and drive the bus directly if

needed. Setting this bit high will drive the bus low until it is cleared or the 1-Wire Master resets. While

the 1-Wire bus is held low no other 1-Wire Master operations will function. By controlling the length of

time this bit is set and the point when the line is sampled, see DQI below, any 1-Wire communication can

be generated by the host controller. To prevent accidental writes to the bus, the DQOE bit in the Interrupt

Enable Register must be set to a 1 before the DQO bit will function. This bit is cleared to a 0 on power-up

or Master Reset.

DQI: DQ Input. This bit is read only and reflects the present state of the 1-Wire bus. It should be used

together with the DQO bit when controlling the bus directly. The state of this bit does not affect any other

functions of the 1-Wire Master. Operation of this bit is unaffected by the state of DQOE.

1WR: 1-Wire Reset. If this bit is set a reset will be generated on the 1-Wire bus. Setting this bit

automatically clears the SRA bit. The 1WR bit will be automatically cleared as soon as the 1-Wire reset

completes. The 1-Wire Master will set the Presence Detect interrupt flag (PD) when the reset is complete

and sufficient time for a presence detect to occur has passed. The result of the presence detect will be

placed in the Interrupt Register bit PDR. If a presence detect pulse was received PDR will be cleared,

otherwise it will be set.

SRA: Search ROM Accelerator. When this bit is set, the 1-Wire Master will switch to Search ROM

Accelerator mode. This mode presupposes that a Reset followed by the Search ROM command (0xF0h)

has already been issued on the 1-Wire bus. For details on how the Search ROM is actually done in the 1-

Wire system, please see [1]. Simply put, the algorithm specifies that the bus master reads two bits (a bit

and its complement), then writes a bit to specify which devices should remain on the bus for further

processing.

After the 1-Wire Master is placed in Search ROM Accelerator mode, the CPU must send 16 bytes to

complete a single Search ROM pass on the 1-Wire bus. These bytes are constructed as follows:

DS1WM

7 of 15

first byte

76543210

r3x3r2x2r1x1r0x0

et cetera

16th byte

76543210

r63 x63 r62 x62 r61 x61 r60 x60

In this scheme, the index (values from 0 to 63, “n”) designates the position of the bit in the ROM ID of a

1-Wire device. The character “x” marks bits that act as a filler and do not require a specific value (don’t

care bits). The character “r” specifies the selected bit value to write at that particular bit in case of a

conflict during the execution of the ROM search.

For each bit position n (values from 0 to 63) the 1-Wire Master will generate three time slots on the 1-

Wire bus. These are referenced as:

b0 for the first time slot (read data)

b1 for the second time slot (read data) and

b2 for the third time slot (write data).

The 1-Wire Master determines the type of time slot b2 (write 1 or write 0) as follows:

b2 = rn if conflict (as chosen by the host)

= b0 if no conflict (there is no alternative)

= 1 if error (there is no response)

The response bytes that will be in the Data Register for the CPU to read during a complete pass through a

Search ROM function using the Search Accelerator consists of 16 bytes as follows:

first byte

76543210

r’3d3r’2d2r’1d1r’0d0

et cetera

16th byte

76543210

r’63 d63 r’62 d62 r’61 d61 r’60 d60

As before, the index designates the position of the bit in the ROM ID of a 1-Wire device. The character

“d” marks the discrepancy flag in that particular bit position. The discrepancy flag will be 1 if there is a

conflict or no response in that particular bit position and 0 otherwise. The character “r’” marks the

actually chosen path at that particular bit position. The chosen path is identical to b2 for the particular bit

position of the ROM ID.

To perform a Search ROM sequence one starts with all bits rn being 0s. In case of a bus error, all

subsequent response bits r’n are 1’s until the Search Accelerator is deactivated by writing 0 to bit 1 of the

Command Register. Thus, if r’63 and d63 are both 1, an error has occurred during the search procedure and

DS1WM

8 of 15

the last sequence has to be repeated. Otherwise r’n (n=0…63) is the ROM code of the device that has

been found and addressed. When the Search ROM process is complete the SRA bit should be cleared in

order to release the 1-Wire Master from Search ROM Accelerator Mode.

For the next Search ROM sequence one re-uses the previous set rn (n=0…63) but sets rm to 1 with “m”

being the index number of the highest discrepancy flag that is 1 and sets all ri to 0 with i>m. This process

is repeated until the highest discrepancy occurs in the same bit position for two consecutive passes.

EXAMPLE — ACCELERATED ROM SEARCH

In this example, the host will use the 1-Wire Master to identify four different devices on the 1-Wire bus.

The ROM data of the devices is as shown (LSB first):

ROM1 = 00110101…

ROM2 = 10101010…

ROM3 = 11110101…

ROM4 = 00010001…

1) The host issues a reset pulse by writing 0x01h to the Command Register. All slave devices respond

simultaneously with a presence detect.

2) The host issues a Search ROM command by writing 0xF0h to the Transmit Buffer.

3) The host places the 1-Wire Master in Accelerator mode by writing 0x02 to the Command Register.

4) The host writes 0x00h to Transmit Buffer and reads the returning data from the Receive Buffer. This

process is repeated for a total of 16 bytes. The data read will contain ROM4 in the r’ locations and

discrepancy bits set at d0 and d2 as shown (r’ locations are underlined, most significant discrepancy is

bolded ):

RECEIVED DATA 1 = 1000100100000001….

5) The host then de-interleaves the data to arrive at a ROM code of 00010001… with the last

discrepancy at location d2.

6) The host writes 0x00h to the Command Register to exit Search Accelerator mode. The host is now

free to send a command or read data directly from this device.

7) Steps 1-6 are now repeated to find the next device. The 16 bytes of data transmitted this time are

identical to ROM4 up until the last discrepancy bit (d2 in this case) which is inverted and all data

following is set to 0 as shown. The received data will contain ROM1 in the r’ locations and bits d0

and d2 will be set again:

TRANSMITTED DATA 2 = 0000010000000000…

RECEIVED DATA 2 = 1000110100010001…

8) Since the most significant discrepancy (d2) did not change, the next most (d0) will be used and the

process repeats. Further iterations contain the data as shown:

TRANSMITTED DATA 3 = 0100000000000000…

RECEIVED DATA 3 = 1110010001000100…

TRANSMITTED DATA 4 = 0101000000000000…

RECEIVED DATA 4 = 1111010100010001…

DS1WM

9 of 15

9) At this point, the most significant discrepancy (d1) did not change so the next most (d0) should be

used. However, d0 has now been reached for the second time and since there are no less significant

discrepancies, the search is complete having found a total of four devices.

OPERATION — FLAGS AND INTERRUPTS

Flags from transmit, receive, and 1-Wire reset operations are located in the Interrupt Register. Only the

Presence Detect flag (PD) is cleared when the Interrupt Register is read, the other flags are cleared

automatically when written to or read from the transmit and receive buffers. These flags can generate an

interrupt on the INTR pin if the corresponding enable bit is set in the Interrupt Enable Register. Reading

the Interrupt Register always sets the INTR pin inactive even if all flags are not cleared.

Interrupt Register (Read-Only)

Addr. 02h DQI NBSY SINT RBF TEMT TBE PDR PD

MSB LSB

PD: Presence Detect. After a 1-Wire Reset has been issued, this flag will be set after the appropriate

amount of time for a presence detect pulse to have occurred. The default state for this bit is 0. This bit is

cleared when the Interrupt Register is read.

PDR: Presence Detect Result. When a Presence Detect interrupt occurs, this bit will reflect the result of

the presence detect read; it will be 0 if a slave device was found, or 1 if no parts were found. The default

state for this bit is 1.

TBE: Transmit Buffer Empty. This flag will be cleared when data is written to the Transmit Buffer and

cleared when that data is transferred to the Transmit Shift Register. The default state for this bit is 1.

TEMT: Transmit Shift Register Empty. This flag will be cleared when data is shifted into the Transmit

Shift Register from the Transmit Buffer and set after the last bit has been transmitted on the 1-Wire bus.

The default state for this bit is 1.

RBF: Receive Buffer Full. This flag will be set when there is a byte waiting to be read in the Receive

Buffer. This flag will be cleared when the byte is read from the Receive Buffer Register. The default state

for this bit is 0.

SINT: Slave Interrupt. This flag is set when the 1-Wire bus is held low by a slave device for a period of

greater than 960us. This bit is cleared when the register is read. The default state for this bit is 0.

NBSY: Not Busy. The default state for this bit is 1 indicating that no operation is currently taking place

inside the 1-Wire Master. It is cleared whenever a read, write, reset, or slave interrupt takes place. When

the operation ends this flag returns to a 1 state.

DQI: DQ Input. This bit is a mirror of bit 3 in the Command Register. This allows the entire status of the

master and the bus to be determined by reading only the Interrupt Register. This bit does not have a

corresponding enable bit in the Interrupt Enable Register.

The Interrupt Enable Register allows the system programmer to specify the source of interrupts, which

will cause the INTR pin to be active, and to define the active state for the INTR pin. When a Master Reset

is received all bits in this register are cleared to 0 disabling all interrupt sources and setting the active

state of the INTR pin to LOW. This means the INTR pin will be pulled high since all interrupts are

disabled. The INTR pin is reset to an inactive state by reading the Interrupt Register.

DS1WM

10 of 15

Interrupt Enable Register (Read / Write)

Addr. 03h DQOE ENBSY ESINT ERBF ETMT ETBE IAS EPD

MSB LSB

EPD: Enable Presence Detect Interrupt. If this bit is a 1, and the Presence Detect flag is set, then the

INTR pin will become active whenever a 1-Wire Reset is sent and an appropriate amount of time has

passed for a presence detect pulse to have occurred.

IAS: INTR Active State. This bit determines the active state for the INTR pin. If this bit is a 1, the INTR

pin is active high; if it is a 0, the INTR pin is active low.

EBTE: Enable Transmit Buffer Empty Interrupt. If this bit is a 1, and the Transmit Buffer Empty flag is

set, then the INTR pin will become active.

ETMT: Enable Transmit Shift Register Empty Interrupt. If this bit is a 1, and the Transmit Shift Register

Empty flag is set, then the INTR pin will become active.

ERBF: Enable Receive Buffer Full Interrupt. If this bit is a 1, and the Receive Buffer Full flag is set, then

the INTR pin will become active.

ESINT: Enable Slave Interrupt. If this bit is a 1, and the Slave Interrupt flag is set, then the INTR pin will

become active.

ENBSY: Enable Not Busy Interrupt. If this bit is a 1, and the Not Busy flag is set, then the INTR pin will

become active.

DQOE: DQ Output Enable. This bit acts as a control select for the DQ bus. When set to 0 (default), the

bus is controlled by the 1-Wire Master as normal. When set to 1, the DQ0 bit located in the Command

left 0 unless the user desires to control the bus manually through the DQ0 bit.

DS1WM

11 of 15

I/0 SIGNALING

The 1-Wire bus requires strict signaling protocols to insure data integrity. The four protocols used by

the 1-Wire Master are the initialization sequence (Reset Pulse followed by Presence Pulse), Write 0,

Write 1, and Read Data. The master initiates all of these types of signaling except the Presence Pulse.

The initialization sequence required to begin any communication with the bus slave is shown in Figure

1. A Presence Pulse following a Reset Pulse indicates the slave is ready to accept a ROM Command.

The 1-Wire Master transmits a reset pulse for tRSTL. The 1-Wire bus line is then pulled high by the pull-

up resistor. After detecting the rising edge on the DQ pin, the slave waits for tPDH and then transmits the

Presence Pulse for tPDL. The master samples the bus at tPDS after the slave responds to test for a valid

presence pulse. The result of this sample is stored in the PDR bit of the Interrupt Register. The reset time

slot ends tRSTH after the master releases the bus.

1-WIRE INITIALIZATION SEQUENCE (RESET PULSE AND PRESENCE

PULSE) Figure 1

WRITE TIME SLOTS

A write time slot is initiated when the 1-Wire Master pulls the 1-Wire bus line from a logic high

(inactive) level to a logic low level. The master generates a Write 1 time slot by releasing the line at tLOW1

and allowing the line to pull up to a logic high level. The line is held low for tLOW0 to generate a Write 0

time slot. A slave device will sample the 1-Wire bus line between 15µs and 60ms (between 2µs and 6ms in

Overdrive mode) after the line falls. If the line is high when sampled, a Write 1 occurs. If the line is low

when sampled, a Write 0 occurs (see Figure 2).

READ TIME SLOTS

A read time slot is initiated when the 1-Wire Master pulls the bus low for at least 1 ms and then releases it.

If the slave device is responding with a 0 it will continue to hold the line low for up to 60ms (6ms in

Overdrive mode), otherwise it will release it immediately. The master will sample the data tRDV from the

start of the read time slot. The master will end the read slot after a time of tSLOT. See Figure 2 for more

information.

LINE TYPE LEGEND:

Wire Master active low

Slave device active low

Resistor pullupBoth Master and

Slave device active low

tPDL

tPDH

VCC

GND

tPDS

DS1WM

12 of 15

1-WIRE WRITE AND READ TIME SLOTS Figure 2

VCC

GND

READ 0 SLOT

tRDV

READ 1 SLOT

tRE

Master Sample Window Master Sample Window

tRDV

LINE TYPE LEGEND:

Wire Master active low

Slave device active low

Resistor pullup

Both Master and

Slave device active low

VCC

GND

WRITE 0 SLOT WRITE 1 SLOT

tRE

SLAVE SAMPLE TIME

OD=0, 8ms typical

OD=1, 2ms max

SLAVE SAMPLE TIME

OD=0, 8ms typical

OD=1, 2ms max

DS1WM

13 of 15

WRITE CYCLE

READ CYCLE

ADS

A1,A0

DATA

D7-D0

VALID

VALID DATA

tADS

tAS tAH

tES

tWR

tDS tDH

tWEN

tAW

ADS

A1,A0

DATA

D7-D0

VALID

VALID DATA

tADS

AS tAH

tES

tRD

tRVD

tHZ

tREN

tAR

DS1WM

14 of 15

GENERATING A 1-WIRE RESET

ADS

A1,A0

DATA

D7-D0 0x01

0x00

INTRPT

tRSTL tRSTH

PDH

tPDL

tPDI

tWRST

tPDS

DS1WM

15 of 15

TIMING SPECIFICATIONS

Symbol Parameter Conditions Min Max Units

tADS Address Strobe Width Note 1,3 60 ns

tAH Address Hold Time Note 1,3 0 ns

tAR Address Latch to Read Note 1,3 60 ns

tAS Address Setup Time Note 1,3 60 ns

tAW Address Latch to Write Note 1,3 60 ns

tDH Data Hold Time Note 1 30 ns

tDS Data Setup Time Note 1 30 ns

tES Enable Setup Time Note 1 60 ns

tHZ RD to Floating Data Delay Note 1 0 100 ns

tLOW0 Write 0 Low Time, OD=0

Write 0 Low Time, OD=1 63 t

8 t

878.75

10 µs

tLOW1 Write 1 Low Time, OD=0

Write 1 Low Time, OD=1 6 t

1 t

17.5

1.25 µs

tPDH Presence Detect High Normal

Presence Detect High Overdrive Note 4 26

2.6 60

6µs

tPDI Presence Detect to INTR Note 1 0 100 ns

tPDL Presence Detect Low Normal

Presence Detect Low Overdrive Note 4 104

10.4 240

24 µs

tPDS Presence Detect Sample, OD=0

Presence Detect Sample, OD=1 30t (Note 2)

337.5

3.75 µs

tRD RD Strobe Width Note 1 125 ns

tRDV Read Data Valid Normal

Read Data Valid Overdrive 15

2µs

tREC Recovery Time 1 µs

tREN Enable Hold Time from RD Note 1 20 ns

tRSTH Reset Time High, OD=0

Reset Time High, OD=1 500t

50t

500

50 625

62.5 µs

tRSTL Reset Time Low, OD=0

Reset Time Low, OD=1 488t

61t

488

61 610

76.25 µs

tRVD Delay from RD to Data Note 1 60 ns

tSLOT Time Slot, OD=0

Time Slot, OD=1 73t

11t

11 91.25

13.75 µs

tTimebase Per i od 1 1.25 µs

tWEN Enable Hold Time from WR Note 1 20 ns

tWR WR Strobe Width Note 1 100 ns

tWRST WR High to Reset Note 1 0 100 ns

NOTES:

1) These values will depend upon the process used to realize the circuit. Values shown are for example

purposes only.

2) The 1-Wire Master will wait for a falling edge on the DQ line to be detected after a reset, for up to 60

µs or 6 µs Overdrive.

3) If ADS is tied low, tAR and tAW are referred from tES ; thus RD or WR must occur at least

tES + tAR or tES + tAW after EN goes low.

4) Timing determined by 1-wire slave

REFERENCES:

[1] Book of iButton Standards, Dallas Semiconductor, online at

http://www.ibutton.com/ibuttons/standard.pdf