DS1803Z-010+T&R - Maxim Integrated

1 of 11 110706

FEATURES

 3V or 5V Operation

 Ultra-Low Power Consumption

 Two Digitally Controlled, 256-Position

Potentiometers

 14-Pin TSSOP (173 mil) and 16-Pin SO (150

mil) Packaging Available for Surface-Mount

Applications

 Addressable Using 3 Address Inputs

 2-Wire Serial Interface

 Operating Temperature Range:

- Industrial: -40°C to +85°C

 Standard Resistance Values:

- DS1803-010 10kΩ

- DS1803-050 50kΩ

- DS1803-100 100kΩ

PIN ASSIGNMENT

PIN DESCRIPTION

L0, L1 - Low End of Resistor

H0, H1 - High End of Resistor

W0,W1 - Wiper terminal of Resistor

VCC - 3V/5V Power Supply Input

A0, A1, A2 - Chip Select Inputs

SDA - Serial Data I/O

SCL - Serial Clock Input

GND - Ground

NC - No Connection

DESCRIPTION

The DS1803 addressable dual digital potentiometer features two independently controlled 256-position

potentiometers. Device control is achieved through a 2-wire serial interface. Three address pins allow up

to 8 DS1803’s to share the same 2-wire interface. The exact wiper position of each potentiometer can be

written or read. The DS1803 is available in a 16-pin DIP, 16-pin SO, and 14-pin TSSOP package. The

device is available in three standard resistance values: 10kΩ, 50kΩ, and 100kΩ and is specified over the

industrial temperature range.

DS1803

Addressable Dual Digital Potentiomete

www.maxim-ic.com

H1 1 14 VCC

L1 2 13 NC

W1 3 12 H0

A2 4 11 L0

A1 5 10 W0

A0 6 9 SDA

GND 7 8 SCL

DS1803 14-PIN TSSOP (173 MIL)

H1 1 16 VCC

NC 2 15 NC

L1 3 14 H0

W1 4 13 L0

A2 5 12 W0

A1 6 11 NC

A0 7 10 SDA

GND 8 9 SCL

DS1803Z 16-PIN SO (150 MIL)

DS1803 16-PIN DIP (300 MIL)

See Mech. Drawings Section on Website

DS1803

2 of 11

DEVICE OPERATION

The DS1803 is an addressable, digitally controlled device which has two 256-position potentiometers. A

functional block diagram of the part is shown in Figure 1. Communication and control of the device is

accomplished via a 2-wire serial interface. Address inputs A0, A1, and A2 allow up to 8 DS1803s to

share the same 2-wire interface.

Each potentiometer is composed of a 256 position resistor array. Two 8-bit registers, each assigned to a

respective potentiometer, are used to set the wiper position on the resistor array. The wiper terminal is

multiplexed to one of 256 positions on the resistor array based on its corresponding 8-bit register value.

For example, the high-end terminals, H0 and H1, have wiper position values FFh while the low-end

terminals, L0 and L1, have wiper position values 00h.

The DS1803 is a volatile device that does not maintain the position of the wiper during power-down or

loss of power. On power-up, the DS1803 wipers’ position will be set to position 00h - the low-end

terminals. The user may then set the wiper value to a desired position.

Communication with the DS1803 takes place over the 2-wire serial interface consisting of the bi-

directional pin, SDA, and the serial clock input, SCL. Complete details of the 2-wire interface are

discussed in the section entitled “2-wire Serial Data Bus.”

Application Considerations

The DS1803 is offered in three standard resistor values, which include 10kΩ, 50kΩ, and 100kΩ. The

resolution of the potentiometer is defined as RTOT/255, where RTOT is the total resistor value of the

potentiometer. The DS1803 is designed to operate using 3V or 5V power supplies over the industrial

(-40°C to +85°C) temperature range. Maximum input signal levels across the potentiometer cannot

exceed the operating power supply of the device.

2-WIRE SERIAL DATA BUS

The DS1803 supports a bi-directional 2-wire bus and data transmission protocol. A device that sends data

on the bus is defined as a transmitter, and a device receiving data as a receiver. The device that controls

the message is called a “master”. The devices that are controlled by the master are “slaves”. The bus must

be controlled by a master device which generates the serial clock (SCL), controls the bus access, and

generates the START and STOP conditions. The DS1803 operates as a slave on the 2-wire bus.

Connections to the bus are made via the open-drain I/O lines SDA and SCL.

The following bus protocol has been defined (see Figure 2).

 Data transfer may be initiated only when the bus is not busy.

 During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes in

the data line while the clock line is high will be interpreted as control signals.

Accordingly, the following bus conditions have been defined:

Bus not busy: Both data and clock lines remain HIGH.

Start data transfer: A change in the state of the data line, from HIGH to LOW, while the clock is

HIGH, defines a START condition.

DS1803

3 of 11

Stop data transfer: A change in the state of the data line, from LOW to HIGH, while the clock line is

HIGH, defines the STOP condition.

Data valid: The state of the data line represents valid data when, after a START condition, the data line

is stable for the duration of the HIGH period of the clock signal. The data on the line must be changed

during the LOW period of the clock signal. There is one clock pulse per bit of data. Figure 2 details how

data transfer is accomplished on the 2-wire bus. Depending upon the state of the R/ W* bit, two types of

data transfer are possible.

Each data transfer is initiated with a START condition and terminated with a STOP condition. The

number of data bytes transferred between START and STOP conditions is not limited, and is determined

by the master device. The information is transferred byte-wise and each receiver acknowledges with a

ninth bit.

Acknowledge: Each receiving device, when addressed, is obliged to generate an acknowledge after the

reception of each byte. The master device must generate an extra clock pulse which is associated with this

acknowledge bit.

A device that acknowledges must pull down the SDA line during the acknowledge clock pulse in such a

way that the SDA line is stable LOW during the HIGH period of the acknowledge related clock pulse. Of

course, setup and hold times must be taken into account. A master must signal an end of data to the slave

by not generating an acknowledge bit on the last byte that has been clocked out of the slave. In this case,

the slave must leave the data line HIGH to enable the master to generate the STOP condition.

1. Data transfer from a master transmitter to a slave receiver: The first byte transmitted by the

master is the control byte (slave address). Next follows a number of data bytes. The slave returns an

acknowledge bit after each received byte.

2. Data transfer from a slave transmitter to a master receiver: The first byte (the slave address) is

transmitted by the master. The slave then returns an acknowledge bit. Next follows a number of data

bytes transmitted by the slave to the master. The master returns an acknowledge bit after all received

bytes other than the last byte. At the end of the last received byte, a ‘not acknowledge’ is returned.

The master device generates all of the serial clock pulses and the START and STOP conditions. A

transfer is ended with a STOP condition or with a repeated START condition. Since a repeated START

condition is also the beginning of the next serial transfer, the bus will not be released.

The DS1803 may operate in the following two modes:

1. Slave receiver mode: Serial data and clock are received through SDA and SCL. After each byte is

received, an acknowledge bit is transmitted. START and STOP conditions are recognized as the

beginning and end of a serial transfer. Address recognition is performed by hardware after reception

of the slave address and direction bit.

2. Slave transmitter mode: The first byte is received and handled as in the slave receiver mode.

However, in this mode the direction bit will indicate that the transfer direction is reversed. Serial data

is transmitted on SDA by the DS1803 while the serial clock is input on SCL. START and STOP

conditions are recognized as the beginning and end of a serial transfer.

DS1803

4 of 11

SLAVE ADDRESS

The control byte is the first byte received following the START condition from the master device. The

control byte consists of a four bit control code; for the DS1803, this is 0101 binary. The next three bits of

the control byte are the device select bits (A2, A1, A0). They are used by the master device to select

which of the devices on the bus are to be accessed. The last bit of the control byte (R/ W*) defines the

operation to be performed. When set to a one a read operation is selected, and when set to a zero a write

operation is selected. Figure 3 shows the control byte for the DS1803.

Following the START condition, the DS1803 monitors the SDA bus for the control byte being

transmitted. Upon receiving a matching control byte, the DS1803 outputs an acknowledge signal on the

SDA line.

COMMAND AND PROTOCOL

The command and protocol structure of the DS1803 allows the user to read or write the potentiometer(s).

The command structures for the part are presented in Figures 4 and 5. Data is transmitted most significant

bit (MSB) first. During communication, the receiving unit always generates the acknowledge.

Reading the DS1803

As shown in Figure 4, the DS1803 provides one read command operation. This operation allows the user

to read both potentiometers. Specifically, the R/ W bit of the control byte is set equal to a 1 for a read

operation. Communication to read the DS1803 begins with a START condition which is issued by the

master device. The control byte from the master device will follow the START condition. Once the

control byte has been received by the DS1803, the part will respond with an ACKNOWLEDGE. The

R/ W bit of the control byte as stated should be set equal to ‘1’ for reading the DS1803.

When the master has received the ACKNOWLEDGE from the DS1803, the master can then begin to

receive potentiometer wiper data. The value of the potentiometer-0 wiper position will be the first

returned from the DS1803. Once the eight bits of the potentiometer-0 wiper position has been transmitted,

the master will need to issue an ACKNOWLEDGE, unless it is the only byte to be read, in which case the

master issues a NOT ACKNOWLEDGE. If desired the master may stop the communication transfer at

this point by issuing the STOP condition. However, if the value of the potentiometer-1 wiper position

value is needed, communication transfer can continue by clocking the remaining eight bits of the

potentiometer-1 value, followed by an NOT ACKNOWLEDGE. Final communication transfer is

terminated by issuing the STOP command.

Writing the DS1803

A data flow diagram for writing the DS1803 is shown in Figure 5. The DS1803 has three write

commands. These include write pot-0, write pot-1, and write pot-0/1. The write pot-0 command allows

the user to write the value of potentiometer-0 and as an option the value of potentiometer-1. The write-1

command allows the user to write the value of potentiometer-1 only. The last write command, write-0/1,

allows the user to write both potentiometers to the same value with one command and one data value

being issued.

All the write operations begin with a START condition. Following the START condition, the master

device will issue the control byte. The read/write bit of the control byte will be set to ‘0’ for writing the

DS1803. Once the control byte has been issued and the master receives the acknowledgment from the

DS1803, the command byte is transmitted to the DS1803. As mentioned above, there exist three write

DS1803

5 of 11

operations that can be used with the DS1803. The binary value of each write command is shown in Figure

5 and also in the Table 1.

2-WIRE COMMAND WORDS Table 1

COMMAND COMMAND VALUE

Write Potentiometer-0 101010 01

Write Potentiometer-1 101010 10

Write Both Potentiometers 101011 11

DS1803

6 of 11

ABSOLUTE MAXIMUM RATINGS*

Voltage on Any Pin Relative to Ground -1.0V to +7.0V

Operating Temperature -40° to +85°C; industrial

Storage Temperature -55°C to +125°C

Soldering Temperature 260°C for 10 seconds

* This is a stress rating only and functional operation of the device at these or any other conditions above

those indicated in the operation sections of this specification is not implied. Exposure to absolute

maximum rating conditions for extended periods of time may affect reliability.

RECOMMENDED OPERATING CONDITIONS (-40°C to +85°C)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Supply Voltage VCC +2.7 5.5 V 1

Resistors Inputs L,H,W GND-0.5 VCC+0.5 V 1

DC ELECTRICAL CONDITIONS (-40°C to +85°C; VCC=2.7V to 5.5V)

PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS NOTES

Supply Current (Active) ICC 200 μA 3

Input Leakage ILI -1 +1 μA

Wiper Resistance RW 400 1000 ohms

Wiper Current IW 1 mA

Input Logic 1 VIH 0.7VCC V

CC+0.5 V 2

Input Logic 0 VIL -0.5 0.3VCC V 2

Input Logic Levels A0, A1,

Input Logic 1

Input Logic 0

0.7VCC

-0.5

VCC+0.5

0.3VCC

V 12

Input Current each I/O Pin 0.4<VI/O<0.9VCC -10 +10 μA

Standby Current ISTBY 20 40 μA 4

VOL1 3 mA sink

current

0.0 0.4 V Low Level Output Voltage

VOL2 6 mA sink

current

0.0 0.6 V

I/O Capacitance CI/0 10 pF

Pulse Width of Spikes

which must be suppressed

by the input filter

tSP Fast Mode 0 50 ns

DS1803

7 of 11

ANALOG RESISTOR CHARACTERISTICS (-40°C to +85°C;VCC=2.7V to 5.5V)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

End-to-End Resistor Tolerance -20 +20 % 17

Absolute Linearity ±0.75

LSB 13

Relative Linearity ±0.3

LSB 14

-3 dB Cutoff Frequency fCUTOFF Hz 11

Temperature Coefficient 750

ppm/°C

Capacitance CI 5

AC ELECTRICAL CHARACTERISTICS (-40°C to +85°C;VCC=2.7V to 5.5V)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

SCL Clock Frequency fSCL 0

0 400

100 kHz 15

Bus Free Time Between

STOP and START Condition tBUF 1.3

4.7 μs 15

Hold Time (Repeated)

START Condition tHD:STA 0.6

4.0 μs 5

Low Period of SCL Clock tLOW 1.3

4.7 μs

High Period of SCL Clock tHIGH 0.6

4.0 μs

Data Hold Time tHD :DAT 0

0 0.9 μs 6,7

Data Setup Time tSU :DAT 100

250 ns 8

Rise Time of both SDA and

SCL Signals tR 20+1CB 300

1000 ns 9

Fall Time of both SDA and

SCL Signals tF 20+1CB 300

300 ns 9

Setup Time for STOP

Condition tSU:STO 0.6

4.0 µs

Capacitive Load for each Bus

Line CB 400 pF 9

NOTES:

1. All voltages are referenced to ground. Currents flowing into device pins are positive. Currents out of

the device pins are negative.

2. I/O pins of fast mode devices will not obstruct SDA and SCL even if VCC is switched off.

3. ICC specified with SDA pin open, SCL = 400 kHz clock rate.

4. ISTBY specified with VCC at 5.0V and SDA, SCL = 5.0V.

DS1803

8 of 11

5. After this period, the first clock pulse is generated.

6. A device must internally provide a hold time of at least 300 ns for the SDA signal (referred to the

VIHMIN of the SCL signal) in order to bridge the undefined region of the falling edge of SCL.

7. The maximum tHD:DAT has only to be met if the device does not stretch the LOW period (tLOW) of the

SCL signal.

8. A fast mode device can be used in a standard mode system, but the requirement tSU:DAT > 250 ns must

then be met. This will automatically be the case if the device does not stretch the LOW period of the

SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next

data bit to the SDA line tRMAX+ tSU:DAT = 1000 + 250=1250 ns before the SCL line is released.

9. CB - total capacitance of one bus line in picofarads, timing referenced to (0.9)(VCC) and (0.1)(VCC).

10. Typical values are for tA = 25°C and nominal supply voltage.

11. -3 dB cutoff frequency characteristics for the DS1803 depend on potentiometer total resistance:

DS1803-010; 1 MHz, DS1803-50; 200 kHz, DS1803-100; 100 kHz.

12. Address Inputs, A0, A1, and A2, should be tied to either VCC or GND depending on the desired

address selections.

13. Absolute linearity is used to determine wiper voltage versus expected voltage as determined by wiper

position. Device test limits are ±1.6 LSB.

14. Relative linearity is used to determine the change in voltage between successive tap positions. Device

test limits ±0.5 LSB.

15. Fast mode.

16. Standard mode.

17. Valid at 25°C only.

DS1803

9 of 11

DS1803 BLOCK DIAGRAM Figure 1

2–WIRE DATA TRANSFER OVERVIEW Figure 2

DS1803

10 of 11

CONTROL BYTE Figure 3

2–WIRE READ PROTOCOL Figure 4

2–WIRE WRITE PROTOCOL Figure 5

Write Pot-0

DS1803

11 of 11

TIMING DIAGRAM Figure 6

DS1803 ORDERING INFORMATION

ORDERING

NUMBER PACKAGE OPERATING

TEMPERATURE VERSION

DS18030-010 16L DIP -40°C TO +85°C 10 kΩ

DS18030-050 16L DIP -40°C TO +85°C 50 kΩ

DS18030-100 16L DIP -40°C TO +85°C 100 kΩ

DS1803E-010 14L TSSOP (173 MIL) -40°C TO +85°C 10 kΩ

DS1803E-050 14L TSSOP (173 MIL) -40°C TO +85°C 50 kΩ

DS1803E-100 14L TSSOP (173 MIL) -40°C TO +85°C 100 kΩ

DS1803Z-010 16L SOIC (150 MIL) -40°C TO +85°C 10 kΩ

DS1803Z-050 16L SOIC (150 MIL) -40°C TO +85°C 50 kΩ

DS1803Z-100 16L SOIC (150 MIL) -40°C TO +85°C 100 kΩ

DS1803E-010+ 14L TSSOP (173 MIL) LEAD FREE -40°C TO +85°C 10 kΩ

DS1803E-50+ 14L TSSOP (173 MIL) LEAD FREE -40°C TO +85°C 50 kΩ

DS1803E-100+ 14L TSSOP (173 MIL) LEAD FREE -40°C TO +85°C 100 kΩ

DS1803E-010+T&R 14L TSSOP (173 MIL) LEAD FREE

T&R -40°C TO +85°C 10 kΩ

DS1803E-50+T&R 14L TSSOP (173 MIL) LEAD FREE

T&R -40°C TO +85°C 50 kΩ

DS1803Z-010+ 16L SOIC (150 MIL) LEAD FREE -40°C TO +85°C 10 kΩ

DS1803Z-050+ 16L SOIC (150 MIL) LEAD FREE -40°C TO +85°C 50 kΩ

DS1803Z-100+ 16L SOIC (150 MIL) LEAD FREE -40°C TO +85°C 100 kΩ

DS1803Z-010+T&R 16L SOIC (150 MIL) LEAD FREE

T&R -40°C TO +85°C 10 kΩ

DS1803Z-050+T&R 16L SOIC (150 MIL) LEAD FREE

T&R -40°C TO +85°C 50 kΩ

DS1803Z-100+T&R 16L SOIC (150 MIL) LEAD FREE

T&R -40°C TO +85°C 100 kΩ

DS1803-100+T&R 16L DIP T&R -40°C TO +85°C 100 kΩ

DS1803E-10/T&R 14L TSSOP (173 MIL) T&R -40°C TO +85°C 10 kΩ

DS1803E-50/T&R 14L TSSOP (173 MIL) T&R -40°C TO +85°C 50 kΩ

DS1803E-100/T&R 14L TSSOP (173 MIL) T&R -40°C TO +85°C 100 kΩ

DS1803Z-010/T&R 16L SOIC (150 MIL) T&R -40°C TO +85°C 10 kΩ

DS1803Z-050/T&R 16L SOIC (150 MIL) T&R -40°C TO +85°C 50 kΩ

DS1803Z-100/T&R 16L SOIC (150 MIL) T&R -40°C TO +85°C 100 kΩ

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Maxim Integrated:

DS18030-010+ DS1803E-010+ DS1803E-050+ DS1803E-100+ DS1803Z-010+ DS1803Z-050+ DS1803Z-100+

DS18030-050+ DS18030-100+ DS1803E-010+T&R DS1803E-100+T&R DS1803E-50+T&R DS1803Z-010+T&R

DS1803Z-050+T&R DS1803Z-100+T&R DS1803E-010 DS1803E-050 DS1803E-10/T&R DS1803E-100 DS1803E-

100/T&R DS1803E-50/T&R DS1803Z-010 DS1803Z-010/T&R DS1803Z-050 DS1803Z-010/C03 DS1803Z-100/T&R

DS1803Z-050/T&R DS1803Z-100