SLLS657A - APRIL 2005 - REVISED JUNE 2005 FEATURES 25 5 24 6 23 7 22 8 21 9 20 10 19 11 18 12 17 13 16 14 15 C1+ V+ VCC GND C1- FORCEON FORCEOFF INVALID ROUT2B ROUT1 ROUT2 ROUT3 ROUT4 ROUT5 32 31 30 29 28 27 26 NC VCC V+ C1+ QFN PACKAGE (TOP VIEW) 25 24 GND RIN2 2 23 C1- RIN3 3 22 FORCEON RIN4 4 21 FORCEOFF RIN5 5 20 INVALID DOUT1 6 19 ROUTB2 DOUT2 7 18 ROUT1 DOUT3 8 17 ROUT2 9 10 11 12 13 14 15 16 NC 1 ROUT3 RIN1 ROUT4 * 26 4 ROUT5 * 3 C2+ * * 27 C2- * * * * 28 2 DIN1 * 1 DIN2 * * C2+ C2- V- RIN1 RIN2 RIN3 RIN4 RIN5 DOUT1 DOUT2 DOUT3 DIN3 DIN2 DIN1 V- * DB, DW, OR PW PACKAGE (TOP VIEW) NC * Single-Chip and Single-Supply Interface for IBMTM PC/ATTM Serial Port ESD Protection for RS-232 Bus Pins - 15-kV Human-Body Model (HBM) - 8-kV IEC61000-4-2, Contact Discharge - 15-kV IEC61000-4-2, Air-Gap Discharge Meets or Exceeds Requirements of TIA/EIA-232-F and ITU v.28 Standards Operates With 3-V to 5.5-V VCC Supply Always-Active Noninverting Receiver Output (ROUT2B) Designed to Transmit at a Data Rate up to 500 kbit/s Low Standby Current . . . 1 A Typ External Capacitors . . . 4 x 0.1 F Accepts 5-V Logic Input With 3.3-V Supply Designed to Be Interchangeable With Maxim MAX3243E Serial-Mouse Driveability Auto-Powerdown Feature to Disable Driver Outputs When No Valid RS-232 Signal Is Sensed Applications - Battery-Powered Systems, PDAs, Notebooks, Laptops, Palmtop PCs, and Hand-Held Equipment Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline (DB), and Thin Shrink Small-Outline (PW) Packages NC * DIN3 www.ti.com MAX3243E 3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION DESCRIPTION The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with 15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and 8-kV ESD (IEC61000-4-2, Contact Discharge) protection on serial-port connection pins. The device meets the requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and the serial-port connector. This combination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, or compatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V supply. In addition, the device includes an always-active noninverting output (ROUT2B), which allows applications using the ring indicator to transmit data while the device is powered down. The device operates at data signaling rates up to 250 kbit/s and a maximum of 30-V/s driver output slew rate. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. IBM, PC/AT are trademarks of International Business Machines Corporation. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2005, Texas Instruments Incorporated MAX3243E 3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS657A - APRIL 2005 - REVISED JUNE 2005 DESCRIPTION (CONTINUED) Flexible control options for power management are available when the serial port is inactive. The auto-powerdown feature functions when FORCEON is low and FORCEOFF is high. During this mode of operation, if the device does not sense a valid RS-232 signal, the driver outputs are disabled. If FORCEOFF is set low, both drivers and receivers (except ROUT2B) are shut off, and the supply current is reduced to 1 A. Disconnecting the serial port or turning off the peripheral drivers causes the auto-powerdown condition to occur. Auto-powerdown can be disabled when FORCEON and FORCEOFF are high, and should be done when driving a serial mouse. With auto-powerdown enabled, the device is activated automatically when a valid signal is applied to any receiver input. The INVALID output is used to notify the user if an RS-232 signal is present at any receiver input. INVALID is high (valid data) if any receiver input voltage is greater than 2.7 V or less than -2.7 V or has been between -0.3 V and 0.3 V for less than 30 s. INVALID is low (invalid data) if all receiver input voltages are between -0.3 V and 0.3 V for more than 30 s. Refer to Figure 5 for receiver input levels. The MAX3243EC is characterized for operation from 0C to 70C. The MAX3243EI is characterized for operation from -40C to 85C. AVAILABLE OPTIONS PACKAGED DEVICES (1) TA 0C to 70C -40C to 85C (1) 2 SHRINK SMALL OUTLINE (DB) MAX3243ECDB MAX3243EIDB SMALL OUTLINE (DB) THIN SHRINK SMALL OUTLINE (PW) QUAD FLAT NO-LEAD (RHB) MAX3243ECDW MAX3243ECPW MAX3243ECRHBR (Preview) MAX3243EIDW MAX3243EIPW MAX3243EIRHBR (Preview) The DB, DW, and PW packages are available in both tube and taped & reeled. Add the suffix R to orderable (e.g. MAX3243ECDBR for taped & reeled version). MAX3243E 3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS657A - APRIL 2005 - REVISED JUNE 2005 FUNCTION TABLES ABC EACH DRIVER (1) INPUTS OUTPUT DOUT DRIVER STATUS X Z Powered off Normal operation with auto-powerdown disabled DIN FORCEON FORCEOFF VALID RIN RS-232 LEVEL X X L (1) L H H X H H H H X L L L H Yes H H L H Yes L L L H No Z H L H No Z Normal operation with auto-powerdown enabled Powered off by auto-powerdown feature H = high level, L = low level, X = irrelevant, Z = high impedance EACH RECEIVER (1) INPUTS OUTPUTS RIN2 RIN1, RIN3-RIN5 FORCEOFF VALID RIN RS-232 LEVEL L X L H X L L L L H H ROUT2B ROUT X L Z X H Z H Yes L H H Yes L L L H Yes H H H H H Yes H L Open Open H Yes L H (1) RECEIVER STATUS Powered off while ROUT2B is active Normal operation with auto-powerdown disabled/enabled H = high level, L = low level, X = irrelevant, Z = high impedance (off), Open = input disconnected or connected driver off 3 MAX3243E 3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS657A - APRIL 2005 - REVISED JUNE 2005 LOGIC DIAGRAM (POSITIVE LOGIC) DIN1 DIN2 DIN3 FORCEOFF FORCEON ROUT1 ROUT2B ROUT2 ROUT3 ROUT4 ROUT5 4 14 9 13 10 12 11 DOUT1 DOUT2 DOUT3 22 23 19 Auto-powerdown 21 4 INVALID RIN1 20 18 5 17 6 16 7 15 8 RIN2 RIN3 RIN4 RIN5 MAX3243E 3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS657A - APRIL 2005 - REVISED JUNE 2005 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX VCC Supply voltage range (2) -0.3 6 V V+ Positive output supply voltage range (2) -0.3 7 V 0.3 -7 V 13 V range (2) V- Negative output supply voltage V+ - V- Output supply voltage difference (2) VI Input voltage range VO Output voltage range JA Package thermal impedance (3) (4) Driver (FORCEOFF, FORCEON) -0.3 6 Receiver -25 25 Driver Receiver (INVALID) -13.2 13.2 -0.3 VCC + 0.3 DB package 62 DW package 46 PW package 62 Lead temperature 1,6 mm (1/16 in) from case for 10 s Tstg (1) (2) (3) (4) Storage temperature range -65 UNIT V V C/W 260 C 150 C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to network GND. Maximum power dissipation is a function of TJ(max), JA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) - TA)/JA. Operating at the absolute maximum TJ of 150C can affect reliability. The package thermal impedance is calculated in accordance with JESD 51-7. Recommended Operating Conditions (1) See Figure 6 VCC = 3.3 V Supply voltage VCC = 5 V VIH Driver and control high-level input voltage DIN, FORCEOFF, FORCEON VIL Driver and control low-level input voltage DIN, FORCEOFF, FORCEON VI Driver and control input voltage DIN, FORCEOFF, FORCEON VI Receiver input voltage TA Operating free-air temperature (1) VCC = 3.3 V MIN NOM MAX UNIT 3 3.3 3.6 4.5 5 5.5 V 2 VCC = 5 V V 2.4 MAX3243EC MAX3243EI 0.8 V 0 5.5 V -25 25 V 0 70 -40 85 C Test conditions are C1-C4 = 0.1 F at VCC = 3.3 V 0.3 V; C1 = 0.047 F, C2-C4 = 0.33 F at VCC = 5 V 0.5 V. Electrical Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6) PARAMETER II ICC (1) (2) Input leakage current Supply current (TA = 25C) TEST CONDITIONS FORCEOFF, FORCEON MIN TYP (2) MAX UNIT 0.01 1 A 0.3 1 mA Auto-powerdown disabled No load, FORCEOFF and FORCEON at VCC Powered off No load, FORCEOFF at GND 1 10 Auto-powerdown enabled No load, FORCEOFF at VCC, FORCEON at GND, All RIN are open or grounded, All DIN are grounded 1 10 A Test conditions are C1-C4 = 0.1 F at VCC = 3.3 V 0.3 V; C1 = 0.047 F, C2-C4 = 0.33 F at VCC = 5 V 0.5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25C. 5 MAX3243E 3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS657A - APRIL 2005 - REVISED JUNE 2005 DRIVER SECTION Electrical Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6) PARAMETER MIN TYP (2) MAX TEST CONDITIONS UNIT VOH High-level output voltage All DOUT at RL = 3 k to GND 5 5.4 V VOL Low-level output voltage All DOUT at RL = 3 k to GND -5 -5.4 V VO Output voltage (mouse driveability) DIN1 = DIN2 = GND, DIN3 = VCC, 3-k to GND at DOUT3, DOUT1 = DOUT2 = 2.5 mA 5 IIH High-level input current VI = VCC 0.01 1 A IIL Low-level input current VI at GND 0.01 1 A Vhys Input hysteresis 1 V 60 mA 25 A VCC = 3.6 V, VO = 0 V VCC = 5.5 V, VO = 0 V IOS Short-circuit output current (3) ro Output resistance VCC, V+, and V- = 0 V, VO = 2 V Ioff Output leakage current FORCEOFF = GND, VO = 12 V, (1) (2) (3) 300 V 10M VCC = 0 to 5.5 V Test conditions are C1-C4 = 0.1 F at VCC = 3.3 V 0.3 V; C1 = 0.047 F, C2-C4 = 0.33 F at VCC = 5 V 0.5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25C. Short-circuit durations should be controlled to prevent exceeding the device absolute power dissipation ratings, and not more than one output should be shorted at a time. Switching Characteristics (1) switching characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6) PARAMETER tsk(p) SR(tr) (1) (2) (3) TEST CONDITIONS MIN TYP (2) MAX Maximum data rate CL = 1000 pF, One DOUT switching, RL = 3 k See Figure 1 Pulse skew (3) CL = 150 pF to 2500 pF, RL = 3 k to 7 k, See Figure 2 Slew rate, transition region (see Figure 1) VCC = 3.3 V, RL = 3 k to 7 k, PRR = 250 kbit/s CL = 150 pF to 1000 pF 6 30 CL = 150 pF to 2500 pF 4 30 250 500 UNIT kbit/s 100 ns V/s Test conditions are C1-C4 = 0.1 F at VCC = 3.3 V + 0.3 V; C1 = 0.047 F, C2-C4 = 0.33 F at VCC = 5 V 0.5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25C. Pulse skew is defined as |tPLH - tPHL| of each channel of the same device. ESD Protection PARAMETER Driver outputs (pins 9-11) 6 TEST CONDITIONS TYP UNIT HBM 15 kV IEC61000-4-2, Air-Gap Discharge 15 kV IEC61000-4-2, Contact Discharge 8 kV MAX3243E 3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS657A - APRIL 2005 - REVISED JUNE 2005 RECEIVER SECTION Electrical Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6) PARAMETER TEST CONDITIONS VOH High-level output voltage IOH = -1 mA VOL Low-level output voltage IOH = 1.6 mA TYP (2) VCC - 0.6 VCC - 0.1 MAX VCC = 3.3 V 1.6 2.4 VCC = 5 V 1.9 2.4 Positive-going input threshold voltage VIT- Negative-going input threshold voltage Vhys Input hysteresis (VIT+ - VIT-) Ioff Output leakage current (except ROUT2B) FORCEOFF = 0 V ri Input resistance VI = 3 V or 25 V VCC = 3.3 V 0.6 1.1 VCC = 5 V 0.8 1.4 UNIT V 0.4 VIT+ (1) (2) MIN V V V 0.5 V 0.05 10 A 5 7 k 3 Test conditions are C1-C4 = 0.1 F at VCC = 3.3 V 0.3 V; C1 = 0.047 F, C2-C4 = 0.33 F at VCC = 5 V 0.5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25C. Switching Characteristics (1) over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) PARAMETER TEST CONDITIONS tPLH Propagation delay time, low- to high-level output tPHL Propagation delay time, high- to low-level output ten Output enable time tdis Output disable time tsk(p) Puse skew (3) (1) (2) (3) CL = 150 pF, See Figure 3 CL = 150 pF, RL = 3 k, See Figure 4 See Figure 3 TYP (2) UNIT 150 ns 150 ns 200 ns 200 ns 50 ns Test conditions are C1-C4 = 0.1 F at VCC = 3.3 V 0.3 V; C1 = 0.047 F, C2-C4 = 0.33 F at VCC = 5 V 0.5 V. All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25C. Pulse skew is defined as |tPLH - tPHL| of each channel of the same device. ESD Protection PARAMETER Driver outputs (pins 4-8) TYP UNIT HBM TEST CONDITIONS 15 kV IEC61000-4-2, Air-Gap discharge 15 kV IEC61000-4-2, Contact Discharge 8 kV 7 MAX3243E 3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS657A - APRIL 2005 - REVISED JUNE 2005 AUTO-POWERDOWN SECTION Electrical Characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5) PARAMETER TEST CONDITIONS MIN VIT+(valid) Receiver input threshold for INVALID high-level output voltage FORCEON = GND, FORCEOFF = VCC VIT-(valid) Receiver input threshold for INVALID high-level output voltage FORCEON = GND, FORCEOFF = VCC -2.7 VT(invalid) Receiver input threshold for INVALID low-level output voltage FORCEON = GND, FORCEOFF = VCC -0.3 VOH INVALID high-level output voltage IOH = -1 mA, FORCEON = GND, FORCEOFF = VCC VOL INVALID low-level output voltage IOL = 1.6 mA, FORCEON = GND, FORCEOFF = VCC MAX UNIT 2.7 V V 0.3 V VCC - 0.6 V 0.4 V Switching Characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5) PARAMETER TEST CONDITIONS TYP (1) UNIT tvalid Propagation delay time, low- to high-level output VCC = 5 V 1 s tinvalid Propagation delay time, high- to low-level output VCC = 5 V 30 s ten Supply enable time VCC = 5 V 100 s (1) 8 All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25C. MAX3243E 3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS657A - APRIL 2005 - REVISED JUNE 2005 PARAMETER MEASUREMENT INFORMATION 3V Generator (see Note B) Input RS-232 Output 50 RL CL (see Note A) 3V FORCEOFF TEST CIRCUIT 0V tTHL Output SR(tr) 6V t THL or tTLH tTLH VOH 3V 3V -3 V -3 V VOL VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: ZO = 50 , 50% duty cycle, tr 10 ns, tf 10 ns. Figure 1. Driver Slew Rate 3V Generator (see Note B) RS-232 Output 50 RL Input 1.5 V 1.5 V 0V CL (see Note A) tPHL tPLH VOH 3V FORCEOFF 50% 50% Output VOL TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 , 50% duty cycle, tr 10 ns, tf 10 ns. Figure 2. Driver Pulse Skew 3 V or 0 V FORCEON 3V Input 1.5 V 1.5 V -3 V Output Generator (see Note B) tPHL 50 3V FORCEOFF tPLH CL (see Note A) VOH 50% Output 50% VOL TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: ZO = 50 , 50% duty cycle, tr 10 ns, tf 10 ns. Figure 3. Receiver Propagation Delay Times 9 MAX3243E 3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS657A - APRIL 2005 - REVISED JUNE 2005 PARAMETER MEASUREMENT INFORMATION 3V Input VCC 3 V or 0 V FORCEON 1.5 V GND S1 -3 V tPZH (S1 at GND) tPHZ (S1 at GND) RL 3 V or 0 V 1.5 V VOH Output 50% Output CL (see Note A) FORCEOFF Generator (see Note B) 50 0.3 V tPLZ (S1 at VCC) tPZL (S1 at VCC) 0.3 V Output 50% VOL TEST CIRCUIT NOTES: A. B. C. D. VOLTAGE WAVEFORMS CL includes probe and jig capacitance. The pulse generator has the following characteristics: ZO = 50 , 50% duty cycle, tr 10 ns, tf 10 ns. tPLZ and tPHZ are the same as tdis. tPZL and tPZH are the same as ten. Figure 4. Receiver Enable and Disable Times 10 MAX3243E 3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS657A - APRIL 2005 - REVISED JUNE 2005 PARAMETER MEASUREMENT INFORMATION 2.7 V 2.7 V 0V Receiver Input 0V -2.7 V -2.7 V ROUT Generator (see Note B) 50 3V tinvalid tvalid 50% VCC 50% VCC -3 V VCC Autopowerdown ten INVALID V+ V+ CL = 30 pF (see Note A) 0.3 V VCC 0V 0.3 V Supply Voltages FORCEOFF FORCEON 0V INVALID Output DIN DOUT V- V- TEST CIRCUIT VOLTAGE WAVEFORMS Valid RS-232 Level, INVALID High 2.7 V Indeterminate 0.3 V 0V -0.3 V If Signal Remains Within This Region For More Than 30 s, INVALID Is Low Indeterminate -2.7 V Valid RS-232 Level, INVALID High Auto-powerdown disables drivers and reduces supply current to 1 A. NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: PRR = 5 kbit/s, ZO = 50 , 50% duty cycle, tr 10 ns, tf 10 ns. Figure 5. INVALID Propagation Delay Timnes and Supply Enabling Time 11 MAX3243E 3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS657A - APRIL 2005 - REVISED JUNE 2005 APPLICATION INFORMATION C1+ 1 + C2 - 2 3 C2- VCC V- GND + C1- RIN1 RIN2 RS-232 Inputs RIN3 RIN4 RIN5 DOUT1 RS-232 Outputs DOUT2 4 27 + - 26 25 C3 + - + CBYPASS - = 0.1 F C1 24 23 FORCEON 5 Autopowerdown C4 - V+ C2+ 28 6 7 22 FORCEOFF 8 21 9 20 10 19 INVALID ROUT2B ROUT1 5 k DOUT3 11 18 ROUT2 5 k DIN3 12 Logic Outputs 17 ROUT3 5 k Logic Inputs DIN2 13 16 ROUT4 5 k DIN1 14 15 ROUT5 5 k C3 can be connected to VCC or GND. NOTES: A. Resistor values shown are nominal. B. Nonpolarized ceramic capacitors are acceptable. If polarized tantalum or electrolytic capacitors are used, they should be connected as shown. VCC vs CAPACITOR VALUES VCC C1 C2, C3, and C4 3.3 V 0.3 V 5 V 0.5 V 3 V to 5.5 V 0.1 F 0.047 F 0.1 F 0.1 F 0.33 F 0.47 F Figure 6. Typical Operating Circuit and Capacitor Values 12 MAX3243E 3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS657A - APRIL 2005 - REVISED JUNE 2005 APPLICATION INFORMATION ESD Protection TI MAX3243E devices have standard ESD protection structures incorporated on the pins to protect against electrostatic discharges encountered during assembly and handling. In addition, the RS232 bus pins (driver outputs and receiver inputs) of these devices have an extra level of ESD protection. Advanced ESD structures were designed to successfully protect these bus pins against ESD discharge of 15-kV in all states: normal operation, shutdown, and powered down. The MAX3243E devices are designed to continue functioning properly after an ESD occurrence without any latchup. The MAX3243E devices have three specified ESD limits on the driver outputs and receiver inputs, with respect to GND: * 15-kV Human Body Model (HBM) * 15-kV IEC61000-4-2, Air-Gap Discharge (formerly IEC1000-4-2) * 8-kV IEC61000-4-2, Contact Discharge ESD Test Conditions ESD testing is stringently performed by TI, based on various conditions and procedures. Please contact TI for a reliability report that documents test setup, methodology, and results. Human Body Model (HBM) The Human Body Model of ESD testing is shown in Figure 7, while Figure 8 shows the current waveform that is generated during a discharge into a low impedance. The model consists of a 100-pF capacitor, charged to the ESD voltage of concern, and subsequently discharged into the DUT through a 1.5k- resistor. RD 1.5 k VHBM + - CS 100 pF DUT Figure 7. HBM ESD Test Circuit 13 MAX3243E 3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS657A - APRIL 2005 - REVISED JUNE 2005 APPLICATION INFORMATION 1.5 VHBM = 2 kV I DUT (A) 1.0 0.5 DUT = 10-V 1- Zener Diode 0.0 0 50 100 150 200 Time (ns) Figure 8. Typical HBM Current Waveform IEC61000-4-2 (Formerly Known as IEC1000-4-2) Unlike the HBM, MM, and CDM ESD tests that apply to component level integrated circuits, the IEC61000-4-2 is a system-level ESD testing and performance standard that pertains to the end equipment. The MAX3243E is designed to enable the manufacturer in meeting the highest level (Level 4) of IEC61000-4-2 ESD protection with no further need of external ESD protection circuitry. The more stringent IEC test standard has a higher peak current than the HBM, due to the lower series resistance in the IEC model. Figure 9 shows the IEC61000-4-2 model, and Figure 10 shows the current waveform for the corresponding 8-kV Contact-Discharge (Level 4) test. This waveform is applied to a probe that has been connected to the DUT. On the other hand, the corresponding 15-kV (Level 4) Air-Gap Discharge test involves approaching the DUT with an already energized probe. High-Voltage DC Source + - 50-100 M 330 RC RD CS 150 pF Figure 9. Simplified IEC61000-4-2 ESD Test Circuit 14 DUT MAX3243E 3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION www.ti.com SLLS657A - APRIL 2005 - REVISED JUNE 2005 APPLICATION INFORMATION I (30A) 100% (Vcontact = 8 kV) I Peak 90% (16A) (8A) 10% t 30 ns 60 ns tr = 0.7 ns to 1 ns Figure 10. Typical Current Waveform of IEC61000-4-2 ESD Generator Machine Model The Machine Model (MM) ESD test applies to all pins using a 200-pF capacitor with no discharge resistance. The purpose of the MM test is to simulate possible ESD conditions that can occur during the handling and assembly processes of manufacturing. In this case, ESD protection is required for all pins, not just RS-232 pins. However, after PC board assembly, the MM test is no longer as pertinent to the RS-232 pins. 15 PACKAGE OPTION ADDENDUM www.ti.com 5-Dec-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty MAX3243ECDB ACTIVE SSOP DB 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3243ECDBE4 ACTIVE SSOP DB 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3243ECDBR ACTIVE SSOP DB 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3243ECDBRE4 ACTIVE SSOP DB 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3243ECDW ACTIVE SOIC DW 28 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3243ECDWR ACTIVE SOIC DW 28 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3243ECPW ACTIVE TSSOP PW 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3243ECPWE4 ACTIVE TSSOP PW 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3243ECPWR ACTIVE TSSOP PW 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3243ECPWRE4 ACTIVE TSSOP PW 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3243ECRHBR PREVIEW QFN RHB 32 3000 TBD Call TI MAX3243EIDB ACTIVE SSOP DB 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3243EIDBR ACTIVE SSOP DB 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3243EIDW ACTIVE SOIC DW 28 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3243EIDWR ACTIVE SOIC DW 28 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3243EIPW ACTIVE TSSOP PW 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3243EIPWE4 ACTIVE TSSOP PW 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3243EIPWR ACTIVE TSSOP PW 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3243EIPWRE4 ACTIVE TSSOP PW 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MAX3243EIRHBR PREVIEW QFN RHB 32 3000 20 20 TBD Lead/Ball Finish Call TI MSL Peak Temp (3) Call TI Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 5-Dec-2005 for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 MECHANICAL DATA MSSO002E - JANUARY 1995 - REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0-8 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MTSS001C - JANUARY 1995 - REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated