NLU2G04 Dual Inverter The NLU2G04 MiniGatet is an advanced high-speed CMOS dual inverter in ultra-small footprint. The NLU2G04 input and output structures provide protection when voltages up to 7.0 V are applied, regardless of the supply voltage. www.onsemi.com Features High Speed: tPD = 3.5 ns (Typ) @ VCC = 5.0 V Low Power Dissipation: ICC = 1 mA (Max) at TA = 25C Power Down Protection Provided on inputs Balanced Propagation Delays Overvoltage Tolerant (OVT) Input and Output Pins Ultra-Small Packages These are Pb-Free Devices MARKING DIAGRAMS 6 ULLGA6 1.0 x 1.0 CASE 613AD HM ULLGA6 1.2 x 1.0 CASE 613AE HM ULLGA6 1.45 x 1.0 CASE 613AF HM UDFN6 1.0 x 1.0 CASE 517BX D 1 HM M M 1 1 IN A1 UDFN6 MU SUFFIX CASE 517AA Y * * * * * * * OUT Y1 GND 2 5 VCC IN A2 3 4 OUT Y2 1 1 Figure 1. Pinout (Top View) IN A1 1 OUT Y1 IN A2 1 OUT Y2 1 UDFN6 1.45 x 1.0 CASE 517AQ Figure 2. Logic Symbol 1 H M PIN ASSIGNMENT 1 = Device Marking = Date Code IN A1 2 GND 3 IN A2 4 OUT Y2 5 VCC 6 OUT Y1 ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. FUNCTION TABLE A Y L H H L (c) Semiconductor Components Industries, LLC, 2014 October, 2014 - Rev. 5 1 Publication Order Number: NLU2G04/D NLU2G04 MAXIMUM RATINGS Symbol Value Unit VCC DC Supply Voltage -0.5 to +7.0 V VIN DC Input Voltage -0.5 to +7.0 V DC Output Voltage -0.5 to +7.0 V VIN < GND -20 mA VOUT < GND 20 mA VOUT Parameter IIK DC Input Diode Current IOK DC Output Diode Current IO DC Output Source/Sink Current 12.5 mA ICC DC Supply Current Per Supply Pin 25 mA IGND DC Ground Current per Ground Pin 25 mA TSTG Storage Temperature Range -65 to +150 C TL Lead Temperature, 1 mm from Case for 10 Seconds 260 C TJ Junction Temperature Under Bias 150 C MSL FR ILATCHUP Moisture Sensitivity Level 1 Flammability Rating Oxygen Index: 28 to 34 UL 94 V-0 @ 0.125 in Latchup Performance Above VCC and Below GND at 125 C (Note 2) 500 mA Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm-by-1 inch, 2 ounce copper trace no air flow. 2. Tested to EIA / JESD78. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit 1.65 5.5 V VCC Positive DC Supply Voltage VIN Digital Input Voltage 0 5.5 V Output Voltage 0 5.5 V -55 +125 C 0 0 100 20 ns/V VOUT TA Operating Free-Air Temperature Dt/DV Input Transition Rise or Fall Rate VCC = 3.3 V 0.3 V VCC = 5.0 V 0.5 V www.onsemi.com 2 NLU2G04 DC ELECTRICAL CHARACTERISTICS Symbol VIH VIL VOH VOL Parameter VCC (V) Conditions Low-Level Input Voltage Low-Level Input Voltage High-Level Output Voltage Low-Level Output Voltage TA = 25 5C Min Typ TA = +855C Max Min 1.65 0.75 x VCC 0.75 x VCC 2.3 to 5.5 0.70 x VCC 0.70 x VCC Max TA = -555C to +1255C Min Max V 1.65 0.25 x VCC 0.25 x VCC 0.25 x VCC 2.3 to 5.5 0.30 x VCC 0.30 x VCC 0.30 x VCC VIN = VIH or VIL IOH = -50 mA 2.0 3.0 4.5 1.9 2.9 4.4 VIN = VIH or VIL IOH = -4 mA IOH = -8 mA 3.0 4.5 2.58 3.94 VIN = VIH or VIL IOL = 50 mA 2.0 3.0 4.5 VIN = VIH or VIL IOL = 4 mA IOL = 8 mA 2.0 3.0 4.5 Unit 1.9 2.9 4.4 1.9 2.9 4.4 2.48 3.80 2.34 3.66 V V V 0 0 0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 0.36 0.36 0.44 0.44 0.52 0.52 V IIN Input Leakage Current 0 v VIN v 5.5 V 0 to 5.5 0.1 1.0 1.0 mA ICC Quiescent Supply Current 0 v VIN v VCC 5.5 1.0 10 40 mA Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 nS) TA = 25 5C TA = +855C TA = -555C to +1255C Symbol Parameter VCC (V) Test Condition Typ Max Max Unit tPLH, tPHL Propagation Delay, Input A to Output Y 3.0 to 3.6 CL = 15 pF 4.5 7.1 8.5 10.0 ns CL = 50 pF 6.4 10.6 12.0 14.5 4.5 to 5.5 CL = 15 pF 3.5 5.5 6.5 8.0 CL = 50 pF 4.5 7.5 8.5 10.0 4 10 10 10.0 CIN Input Capacitance CPD Power Dissipation Capacitance (Note 3) Min 5.0 8.0 Min Max Min pF pF 3. CPD is defined as the value of the internal equivalent capacitance which is calculated from the dynamic operating current consumption without load. Average operating current can be obtained by the equation ICC(OPR) = CPD * VCC * fin + ICC. CPD is used to determine the no-load dynamic power consumption: PD = CPD * VCC2 * fin + ICC * VCC. www.onsemi.com 3 NLU2G04 VCC A or B 50% GND tPLH Y tPHL 50% VCC Figure 3. Switching Waveforms OUTPUT INPUT CL* *Includes all probe and jig capacitance. A 1-MHz square input wave is recommended for propagation delay tests. Figure 4. Test Circuit ORDERING INFORMATION Package Shipping UDFN6, 1.2 x 1.0, 0.4P (Pb-Free) 3000 / Tape & Reel NLU2G04AMX1TCG ULLGA6, 1.45 x 1.0, 0.5P (Pb-Free) 3000 / Tape & Reel NLU2G04BMX1TCG ULLGA6, 1.2 x 1.0, 0.4P (Pb-Free) 3000 / Tape & Reel NLU2G04CMX1TCG ULLGA6, 1.0 x 1.0, 0.35P (Pb-Free) 3000 / Tape & Reel NLU2G04AMUTCG UDFN6, 1.45 x 1.0, 0.5P (Pb-Free) 3000 / Tape & Reel NLU2G04CMUTCG UDFN6, 1.0 x 1.0, 0.35P (Pb-Free) 3000 / Tape & Reel Device NLU2G04MUTCG For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. www.onsemi.com 4 NLU2G04 PACKAGE DIMENSIONS UDFN6 1.45x1.0, 0.5P CASE 517AQ ISSUE O A B D L L L1 PIN ONE REFERENCE 0.10 C EEE EEE DETAIL A E OPTIONAL CONSTRUCTIONS DETAIL B MOLD CMPD DETAIL B 0.05 C 6X DIM A A1 A2 b D E e L L1 EE EE EXPOSED Cu TOP VIEW 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. OPTIONAL CONSTRUCTIONS A MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.07 REF 0.20 0.30 1.45 BSC 1.00 BSC 0.50 BSC 0.30 0.40 --- 0.15 MOUNTING FOOTPRINT 0.05 C A1 A2 SIDE VIEW e 6X C 6X SEATING PLANE L 1.24 3 1 DETAIL A 6X 0.53 6 0.30 PACKAGE OUTLINE 4 BOTTOM VIEW 6X 0.50 PITCH DIMENSIONS: MILLIMETERS b 0.10 C A B 0.05 C 1 NOTE 3 *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 5 NLU2G04 PACKAGE DIMENSIONS UDFN6 1.0x1.0, 0.35P CASE 517BX ISSUE O PIN ONE REFERENCE NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.20 MM FROM TERMINAL TIP. 4. PACKAGE DIMENSIONS EXCLUSIVE OF BURRS AND MOLD FLASH. A B D EEE EEE EEE E 0.10 C 2X 2X 0.10 C DIM A A1 A3 b D E e L L1 TOP VIEW A3 0.05 C A MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.13 REF 0.12 0.22 1.00 BSC 1.00 BSC 0.35 BSC 0.25 0.35 0.30 0.40 0.05 C SIDE VIEW A1 C RECOMMENDED SOLDERING FOOTPRINT* SEATING PLANE 5X e 5X 0.48 L 6X 0.22 3 1 L1 1.18 6 4 BOTTOM VIEW 6X b 0.10 M C A B 0.05 M C 0.53 1 PKG OUTLINE NOTE 3 0.35 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 6 NLU2G04 PACKAGE DIMENSIONS UDFN6, 1.2x1.0, 0.4P CASE 517AA ISSUE C EDGE OF PACKAGE PIN ONE REFERENCE 2X 0.10 C EE EE EE L1 E DETAIL A Bottom View (Optional) TOP VIEW 2X EXPOSED Cu 0.10 C (A3) 0.10 C A1 A 10X 0.08 C EEE EEE A3 DETAIL B Side View (Optional) 5X MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.127 REF 0.15 0.25 1.20 BSC 1.00 BSC 0.40 BSC 0.30 0.40 0.00 0.15 0.40 0.50 MOUNTING FOOTPRINT* 6X 6X 0.42 C A1 DIM A A1 A3 b D E e L L1 L2 MOLD CMPD SEATING PLANE SIDE VIEW 1 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 mm FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. A B D 0.22 L 3 L2 6X b 0.10 C A B 0.05 C 6 0.40 PITCH 4 e NOTE 3 1.07 DIMENSIONS: MILLIMETERS BOTTOM VIEW *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 7 NLU2G04 PACKAGE DIMENSIONS ULLGA6 1.0x1.0, 0.35P CASE 613AD ISSUE A PIN ONE REFERENCE 0.10 C EE EE 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D E DIM A A1 b D E e L L1 TOP VIEW 0.05 C A 6X 0.05 C MOUNTING FOOTPRINT SOLDERMASK DEFINED* SEATING PLANE SIDE VIEW C A1 MILLIMETERS MIN MAX --- 0.40 0.00 0.05 0.12 0.22 1.00 BSC 1.00 BSC 0.35 BSC 0.25 0.35 0.30 0.40 5X 0.48 6X 0.22 e 5X L NOTE 4 3 1 1.18 L1 0.53 6 4 6X b 0.35 PITCH DIMENSIONS: MILLIMETERS 0.10 C A B BOTTOM VIEW 1 PKG OUTLINE 0.05 C NOTE 3 *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 8 NLU2G04 PACKAGE DIMENSIONS ULLGA6 1.2x1.0, 0.4P CASE 613AE ISSUE A PIN ONE REFERENCE 0.10 C EE EE 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D E DIM A A1 b D E e L L1 TOP VIEW 0.05 C A 6X 0.05 C SEATING PLANE SIDE VIEW MOUNTING FOOTPRINT SOLDERMASK DEFINED* C A1 MILLIMETERS MIN MAX --- 0.40 0.00 0.05 0.15 0.25 1.20 BSC 1.00 BSC 0.40 BSC 0.25 0.35 0.35 0.45 5X 0.49 e 5X L NOTE 4 3 1 6X 0.26 1.24 L1 0.53 6 4 6X b 0.10 C A B BOTTOM VIEW 0.05 C NOTE 3 1 PKG OUTLINE 0.40 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 9 NLU2G04 PACKAGE DIMENSIONS ULLGA6 1.45x1.0, 0.5P CASE 613AF ISSUE A PIN ONE REFERENCE 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D EEE EEE E DIM A A1 b D E e L L1 TOP VIEW 0.10 C 0.05 C A 6X 0.05 C MOUNTING FOOTPRINT SOLDERMASK DEFINED* SEATING PLANE SIDE VIEW 5X C A1 e 5X L MILLIMETERS MIN MAX --- 0.40 0.00 0.05 0.15 0.25 1.45 BSC 1.00 BSC 0.50 BSC 0.25 0.35 0.30 0.40 0.49 NOTE 4 3 1 6X 0.30 1.24 L1 0.53 6 4 BOTTOM VIEW 6X b 0.10 C A B 0.05 C NOTE 3 1 PKG OUTLINE 0.50 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. MiniGate is a trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and the are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 www.onsemi.com 10 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NLU2G04/D