UC1903 UC2903 UC3903 www.ti.com ........................................................................................................................................ SLUS233A - OCTOBER 1999 - REVISED SEPTEMBER 2008 Quad Supply and Line Monitor FEATURES DESCRIPTION 1 * * * * * * * * Inputs for Monitoring up to Four Separate Supply Voltage Levels Internal Inverter for Sensing a Negative Supply Voltage Line/Switch Sense Input for Early Power Source Failure Warning Programmable Under- and Over-Voltage Fault Thresholds with Proportional Hysteresis A Precision 2.5-V Reference General Purpose Op-Amp for Auxiliary Use Three High Current, >3 0mA, Open-Collector Outputs Indicate Over-Voltage, Under-Voltage and Power OK Conditions 8-V to 40-V Supply Operation with 7-mA Stand-By Current The UC1903 family of quad supply and line monitor integrated circuits will respond to under- and over-voltage conditions on up to four continuously monitored voltage levels. An internal op-amp inverter allows at least one of these levels to be negative. A separate line/switcher sense input is available to provide early warning of line or other power source failures. The fault window adjustment circuit on these devices provides easy programming of under- and over-voltage thresholds. The thresholds, centered around a precision 2.5-V reference, have an input hysteresis that scales with the window width for precise, glitch-free operation. A reference output pin allows the sense input fault windows to be scaled independently using simple resistive dividers. The three open collector outputs on these devices sink in excess of 30 mA of load current when active. The under- and over-voltage outputs respond after separate, user defined, delays to respective fault conditions. The third output is active during any fault condition including under- and over-voltage, line/switcher faults, and input supply under-voltage. The off state of this output indicates a "power OK" situation. BLOCK DIAGRAM Note: Pin numbers refer to J, N and DW packages. 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 1999-2008, Texas Instruments Incorporated UC1903 UC2903 UC3903 SLUS233A - OCTOBER 1999 - REVISED SEPTEMBER 2008 ........................................................................................................................................ www.ti.com DESCRIPTION (CONT.) An additional, uncommitted, general purpose op-amp is also included. This op-amp, capable of sourcing 20 mA of output current, can be used for a number of auxiliary functions including the sensing and amplification of a feedback error signal when the 2.5-V output is used as a system reference. These parts operate over an 8-V to 40-V input supply range and require a typical stand-by current of only 7 mA. CONNECTION DIAGRAMS DIL-18, SOIC-18 J or N, DW PACKAGE (TOP VIEW) 6 13 7 12 8 11 9 10 LINE/SWITCHER SENSE POWER OK UV DELAY UV FAULT OV FAULT OV DELAY 3 2 G.P. OP-AMP N.I. 14 1 20 19 18 G.P. OP-AMP OUT GND 4 17 LINE/SWITCHER WINDOW ADJUST 5 NC 6 SENSE 4 INVERT 7 INPUT SENSE 4 8 SENSE 16 POWER OK 15 UV DELAY 14 UV FAULT 9 10 11 12 13 OV FAULT 5 OV DELAY 15 +VIN 16 4 G.P. OP-AMP INV 3 VREF (2.5 V) GND WINDOW ADJUST SENSE 4 INVERT INPUT SENSE 4 SENSE 3 SENSE 2 SENSE 1 G.P. OP-AMP INV. G.P. OP-AMP N.I. G.P. OP-AMP OUT SENSE 2 17 SENSE 1 18 2 GND 1 SENSE 3 +VIN VREF (2.5 V) PLCC-20, LCC-20 Q, L PACKAGE (TOP VIEW) ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range (unless otherwise noted) +VIN VALUE UNIT Supply Voltage +40 V Open Collector Output Voltages. +40 V Open Collector Output Currents. 50 mA Sense 1-4 Input Voltages -0.3 to +20 V Line/Switcher Sense Input Voltage -0.3 to +40 V Op-Amp and Inverter Input Voltages -0.3 to +40 V Op-Amp and Inverter Output Currents . -40 mA Window Adjust Voltage. 0.0 to +10 V Delay Pin Voltages 0.0 to +5 V Reference Output Current -40 mA Power Dissipation at TA = 25C (1) 1000 mW Power Dissipation at TC = 25C (1) 2000 mW Operating Junction Temperature -55 to +150 C Storage Temperature -65 to +150 C 300 C Lead Temperature (Soldering, 10 Seconds) (1) 2 Voltages are referenced to ground (Pin 3). Currents are positive into, negative out of, the specified terminals. Consult Packaging Section of Databook for thermal limitations and considerations of package. Submit Documentation Feedback Copyright (c) 1999-2008, Texas Instruments Incorporated Product Folder Link(s): UC1903 UC2903 UC3903 UC1903 UC2903 UC3903 www.ti.com ........................................................................................................................................ SLUS233A - OCTOBER 1999 - REVISED SEPTEMBER 2008 ELECTRICAL CHARACTERISTICS Unless otherwise stated, these specifications apply for TA = -55C to +125C for the UC1903; -40C to +85C for the UC2903; and 0C to +70C for the UC3903; +VIN = 15V; Sense Inputs (Pins 6-9 and Pin 15) = 2.5V; VPIN 4 = 1.0V, TA = TJ. PARAMETER TEST CONDITIONS UC1903 / UC2903 MIN UC3903 TYP MAX 7 9 MIN UNIT TYP MAX 7 11 mA SUPPLY Input Supply Current No Faults UV, OV and Line Fault Supply Under Voltage Threshold (VSUV) Fault Outputs Enabled 6.0 Minimum Supply to Enable Power OK Output 10 15 7.0 7.5 3.0 4.0 2.5 2.515 2.470 2.535 2.465 5.5 10 18 mA 7.0 8.0 V 3.0 4.0 V 2.5 2.530 V REFERENCE Output Voltage (VREF) TJ = 25C 2.485 Over Temperature 2.465 Load Regulation IL = 0 to 10mA Line Regulation +VIN = 8 to 40V Short Circuit Current TJ = 25C 1 10 1 4 40 2.535 V 1 15 mV 1 8 mV 40 mA FAULT THRESHOLDS (1) OV Threshold Adj. Offset from VREF as a function of VPIN 4 Input = Low to High, 0.5V VPIN 4 2.5V 0.230 0.25 0.270 0.230 0.25 0.270 V/V UV Threshold Adj. Offset from VREF as a function of VPIN 4 Input = High to Low, 0.5V VPIN 4 2.5V -0.270 -0.25 -0.230 -0.270 -0.25 -0.270 V/V OV & UV Threshold Hyst. 0.5V VPIN 4 2.5V 20 30 10 OV & UV Threshold Supply Sensitivity +VIN = 8V to 40V 0.002 0.01 Adjust Pin (Pin 4) Input Bias Current 0.5V VPIN 4 2.5V Line Sense Threshold Input = High to Low Line Sense Threshold Hyst. 10 20 30 mV/V 0.002 0.02 %/V A/V 1 10 1 12 1.94 2.0 2.06 1.9 2.0 2.1 V 125 175 225 100 175 250 mV SENSE INPUTS Sense 1-4 Input Bias Current Line Sense Input Bias Current Input = 2.8V (2) Input = 2.2 (2) Input = 2.3V (2) 1 3 1 6 A -1 -3 -1 -6 A 1 3 1 6 A OV AND UV FAULT DELAY Charging Current (1) (2) A 60 60 Threshold Voltage Delay Pin = Low to High 1.8 1.8 V Threshold Hysteresis TJ = 25C 250 250 mV Delay Ratio of Threshold Voltage to Charging Current 20 30 50 20 30 50 ms/F Reference to pin numbers in this specification pertain to 18 pin DIL N and J packages and 18 pin SOIC DW package. These currents represent maximum input bias currents required as the sense inputs cross appropriate thresholds. Copyright (c) 1999-2008, Texas Instruments Incorporated Product Folder Link(s): UC1903 UC2903 UC3903 Submit Documentation Feedback 3 UC1903 UC2903 UC3903 SLUS233A - OCTOBER 1999 - REVISED SEPTEMBER 2008 ........................................................................................................................................ www.ti.com ELECTRICAL CHARACTERISTICS (continued) Unless otherwise stated, these specifications apply for TA = -55C to +125C for the UC1903; -40C to +85C for the UC2903; and 0C to +70C for the UC3903; +VIN = 15V; Sense Inputs (Pins 6-9 and Pin 15) = 2.5V; VPIN 4 = 1.0V, TA = TJ. PARAMETER TEST CONDITIONS UC1903 / UC2903 MIN TYP 30 70 UC3903 MAX MIN TYP 30 70 MAX UNIT FAULT OUTPUTS (OV, UV, AND POWER 0K) Maximum Current VOUT = 2V mA Saturation Voltage IOUT = 12mA 0.25 0.40 0.25 0.40 V Leakage Current VOUT = 40 V 3 25 3 25 A 2 8 2 10 mV 0.1 2 0.1 4 A SENSE 4 INVERTER (3) Input Offset Voltage Input Bias Current Open Loop Gain PSRR +VIN = 8 to 40 V 65 80 65 80 65 100 65 100 Unity Gain Frequency Slew Rate Short Circuit Current dB dB 1 1 MHz 0.4 0.4 V/s 40 40 mA TJ = 2C G.P. OP-AMP (3) Input Offset Voltage Input Bias Voltage Input Offset Current Open Loop Gain 1 5 1 8 mV 0.1 2 0.1 4 A 0.01 .5 0.01 1.0 A 65 120 65 120 dB dB CMRR VCM = 0 to +VIN = 2.0V 65 100 65 100 PSRR +VIN = 8 to 40V 65 100 65 100 Unity Gain Frequency Slew Rate Short Circuit Current (3) 4 dB 1 1 MHz 0.4 0.4 V/s 40 40 mA TJ = 25C When either the G.P. OP-Amp, or the Sense 4 Inverter, are configured for sensing a negative supply voltage, the divider resistance at the inverting input should be chosen such that the nominal divider current is 1.4mA. With the divider current at or below this level possible latching of the circuit is avoided. Proper operation for currents at or below 1.4mA is 100% tested in production. Submit Documentation Feedback Copyright (c) 1999-2008, Texas Instruments Incorporated Product Folder Link(s): UC1903 UC2903 UC3903 UC1903 UC2903 UC3903 www.ti.com ........................................................................................................................................ SLUS233A - OCTOBER 1999 - REVISED SEPTEMBER 2008 Block Diagram UC1903 +VIN REFERENCE CIRCUIT IOA IOB Q4 1.25 V Q2 Q1 OV THRESHOLD Q3 2.5 V OUTPUT 15 W R1 2.5 kW R2 2.5 kW R3 RA VADJ RS A. TO OV HYSTERESIS CONTROL 1.84 kW R5 VADJ IO = R4 0.16 kW R7 0.16 kW R8 1.84 kW FAULT WINDOW THREAHOLD and HYSTERESIS CIRCUITS UV THRESHOLD R4 8 kW BIAS CANCELLATION AND MIRROR CIRCUITS R6 IOD IOC Q5 TO UV HYSTERESIS CONTROL The UC1903 fault window circuitry generates OV and UV thresholds centered around the 2.5-V reference. Window magnitude and threshold hysteresis are proportional to the window adjust input voltage at Pin 4. Figure 1. Operation and Application Information Typical Characteristics Typical 2.5 V Reference vs Temperature Characteristic Typical Fault Delay vs Temperature Characteristic (CDELAY 270 pF) 0.2 0.1 40 - 0.1 35 Delay - ms/mF Reference Change - % 0 - 0.2 - 0.3 - 0.4 30 - 0.5 25 - 0.6 - 0.7 - 55 - 35 - 15 5 25 45 65 85 TJ - Junction Temperature - C 105 125 20 - 55 - 35 - 15 5 25 45 65 85 TJ - Junction Temperature - C Copyright (c) 1999-2008, Texas Instruments Incorporated Product Folder Link(s): UC1903 UC2903 UC3903 105 Submit Documentation Feedback 125 5 UC1903 UC2903 UC3903 SLUS233A - OCTOBER 1999 - REVISED SEPTEMBER 2008 ........................................................................................................................................ www.ti.com OPERATION AND APPLICATION INFORMATION Setting a Fault Window The fault thresholds on the UC1903 are generated by creating positive and negative offsets, equal in magnitude, that are referenced to the chip's 2.5-V reference. The resulting fault window is centered around 2.5 V and has a magnitude equal to that of the applied offsets. Simplified schematics of the fault window and reference circuits are shown in Figure 1 along with the Typical Characteristics diagrams. The magnitude of the offsets is determined by the voltage applied at the window adjust pin, Pin 4. A bias cancellation circuit keeps the input current required at Pin 4 low, allowing the use of a simple resistive divider off the reference to set the adjust pin voltage. The adjust voltage at Pin 4 is internally applied across R4, and an 8-k resistor. The resulting current is mirrored four times to generate current sources IOA, IOB, IOC, and IOD, all equal in magnitude. When all four of the sense inputs are inside the fault window, a no-fault condition, Q4 and Q5 are turned on. In combination with D1 and D2 this prevents LOB and LOD from affecting the fault thresholds. In this case, the OV and UV thresholds are equal to VREF + IOA(R5 + R6) and VREF - IOC(R7 + R8) respectively. The fault window can be expressed as: 2.5 V VADJ 4 (1) In terms of a sensed nominal voltage level, VS, the window as a percent variation is: VS (10 x VADJ )% (2) 3.125 25 3 20 2.875 15 Hysteresis 2.750 10 2.625 5 Fault Window 2.5 0 -5 2.375 -10 2.25 No Fault Supply Fault Window - % Fault Window at Sense Inputs - V When a sense input moves outside the fault window given in Equation 1, the appropriate hysteresis control signal turns off Q4 or Q5. For the under-voltage case, Q5 is disabled and current source IOB flows through D2. The net current through R7 becomes zero as IOB cancels IOC, giving an 8% reduction in the UV threshold offset. The overvoltage case is the same, with Q4 turning off, allowing IOD to cancel the current flow, IOA, through R6. The result is a hysteresis at the sense inputs which is always 8% of the window magnitude. This is shown graphically in Figure 2. -15 2.125 Fault 2 -20 Fault Window 1.875 0 1.5 2 0.5 1 Window Adjust Voltage (VADJ) at Pin 4 -25 2.5 Figure 2. Fault Window and Threshold Hysteresis Scale as a Function of the Voltage Applied at Pin 4 6 Submit Documentation Feedback Copyright (c) 1999-2008, Texas Instruments Incorporated Product Folder Link(s): UC1903 UC2903 UC3903 UC1903 UC2903 UC3903 www.ti.com ........................................................................................................................................ SLUS233A - OCTOBER 1999 - REVISED SEPTEMBER 2008 Fault Windows Scaled Independently In many applications, it may be desirable to monitor various supply voltages, or voltage levels, with varying fault windows. Using the reference output and external resistive dividers this is easily accomplished with the UC1903. Figure 3 and Figure 4 illustrate how the fault window at any sense input can be scaled independently of the remaining inputs. Monitored Supply Voltage VS UC1903 R1 SENSE 1-4 INPUT R2 R3 2.5 V REF. Fault window for the Sense Input, in percent, is: R 3 + R 1R 2 /(R1 + R 2) -10 (VADJ) * , R3 for: VS (NOM) * A. R2 = 2.5V R1 + R2 Using the reference output and a resistive divider, a sense input with an independently wider fault window can be generated. Figure 3. UC1903 Sense Input with an Independently Wider Fault Window UC1903 R1 G.P. OP-AMP SENSE INPUT R2 2.5 V REF. SENSE 1-4 INPUT Fault window for the sense input, in percent, is: 10 (VADJ) * A. R2 R1 + R2 The general purpose op-amp on the UC1903 can be used to create a sense input with an independently tighter fault window. Figure 4. UC1903 Sense Input with an Independently Tighter Fault Window Copyright (c) 1999-2008, Texas Instruments Incorporated Product Folder Link(s): UC1903 UC2903 UC3903 Submit Documentation Feedback 7 UC1903 UC2903 UC3903 SLUS233A - OCTOBER 1999 - REVISED SEPTEMBER 2008 ........................................................................................................................................ www.ti.com Figure 4 demonstrates one of many auxiliary functions that the uncommitted op-amp on the UC1903 can be used for. Alternatively, this op-amp can be used to buffer high impedance points, perform logic functions, or for sensing and amplification. For example, the G.P. op-amp, combined with the 2.5-V reference, can be used to produce and buffer an optically coupled feedback signal in isolated supplies with primary side control. The output stage of this op-amp is detailed in Figure 5. The NPN emitter follower provides high source current capability. 20 mA while the substrate device, Q3, provides good transient sinking capability. +VIN 75 mA Q1 Q2 R1 10 kW UC1903 G.P. OP-AMP D1 OUTPUT STAGE Q6 R2 15 W R3 150 W TO OP-AMP INPUT STAGE Q3 Q5 Q4 R4 500 W A. 16 OUTPUT 150 mA The G.P. op-amp on the UC1903 has a high source current (20 mA) capability and enhanced transient sinking capability through substrate device Q3. Figure 5. The G.P. Op-Amp on the UC1903 Sensing a Negative Voltage Level The UC1903 has a dedicated inverter coupled to the sense 4 input. With this inverter, a negative voltage level can be sensed as shown in Figure 6. The output of the inverter is an unbiased emitter follower. By tying the inverting input, Pin 5, high the output emitter follower will be reverse biased, leaving the sense 4 input in a high impedance state. In this manner, the sense 4 input can be used, as the remaining sense inputs would be, for sensing positive voltage levels. UC1903 SENSE 4 INPUT 2.5 V R1 VS R2 SENSE 4 INVERTER GROUND NEGATIVE SUPPLY (-VS) VS (NOM) = 2.5 V Note: A similar scheme w/the G.P. op-amp will allow a second negative supply to be monitored. Figure 6. Inverting the Sense 4 Input for Monitoring a Negative Supply, Accommodated with the Dedicated Inverter 8 Submit Documentation Feedback Copyright (c) 1999-2008, Texas Instruments Incorporated Product Folder Link(s): UC1903 UC2903 UC3903 UC1903 UC2903 UC3903 www.ti.com ........................................................................................................................................ SLUS233A - OCTOBER 1999 - REVISED SEPTEMBER 2008 Using The Line/Switcher Sense Output The line switcher sense input to the UC1903 can be used for early detection of line, switcher, or other power source, failures. Internally referenced to 2.0 V, the line sense comparator will cause the POWER OK output to indicate a fault (active low) condition when the LINE/SWITCHER SENSE input goes from above to below 2.0 V. The line sense comparator has approximately 175 mV of hysteresis requiring the line/switcher input to reach 2.175 V before the POWER OK output device can be turned off, allowing a no-fault indication. In Figure 7 an example showing the use of the LINE/SWITCHER SENSE input for early switcher-fault detection is detailed. A sample signal is taken from the output of the power transformer, rectified and filtered, and used at the line/switcher input. By adjusting the R2C time constant with respect to the switching frequency of the supply and the hold up time of the output capacitor, switcher faults can be detected before supply outputs are significantly affected. POWER LINE INPUT TRANSFORMER FILTER Figure 7. Line/Switcher Sense Input Used for Early Line or Switcher Fault Indication Copyright (c) 1999-2008, Texas Instruments Incorporated Product Folder Link(s): UC1903 UC2903 UC3903 Submit Documentation Feedback 9 UC1903 UC2903 UC3903 SLUS233A - OCTOBER 1999 - REVISED SEPTEMBER 2008 ........................................................................................................................................ www.ti.com OV and UV Comparators Maintain Accurate Thresholds The structure of the OV and UV comparators, shown in Figure 8 results in accurate fault thresholds even in the case where multiple sense inputs cross a fault threshold simultaneously. Unused sense inputs can be tied either to the 2.5-V reference, or to another, utilized, sense input. The four under- and over-voltage sense inputs on the UC1903 are clamped as detailed on the Sense 1 input in Figure 8. The series 2-k resistor, R1, and zener diode Z1, prevent extreme under- and over-voltage conditions from inverting the outputs of the fault comparators. A parasitic diode, D1, is present at the inputs as well. Under normal operation it is advisable to insure that voltage levels at all of the sense inputs stay above -0.3 V. The same type of input protection exists at the line sense input, Pin 15, except a 5-k series resistor is used. The fault delay circuitry on the UC1903 is also shown in Figure 8. In the case of an over-voltage condition at one of the sense inputs Q20 is turned off, allowing the internal 60-mA current source to charge the user-selected delay capacitor. When the capacitor voltage reaches 1.8 V, the OV and POWER OK outputs become active low. When the fault condition goes away Q20 is turned back on, rapidly discharging the delay capacitor. Operation of the under- voltage delay is, with appropriate substitutions, the same. 6.4 V 6.4 V EXT. OV DELAY CAPACITOR 60 mA Q6 Q7 Q8 Q9 Q20 1.8 V OV COMPARATOR Q1 Q2 Q3 Q4 SENSE 1 2 kW 100 mA R1 D1 OV TO OV HYSTERESIS THRESHOLD CONTROL VOLTAGE Z1 5.7 V 6.4 V 50 mA SENSE 2 SENSE 3 SENSE 4 Q10 Q11 Q12 Q13 UV COMPARATOR TO UV THRESHOLD UV VOLTAGE HYSTERESIS Q14 CONTROL Q16 Q17 VREF EXT. UV DELAY CAPACITOR 6.4 V 60 mA Q19 Q15 A. Q5 OV FAULT INDICATION TO OUTPUT LOGIC Q18 1.8 V UV FAULT INDICATION TO OUTPUT LOGIC The OV and UV comparators on the UC1903 trigger respective fault delay circuits when one or more of the sense inputs move outside the fault window. Input clamps insure proper operation under extreme fault conditions. Terminating the UV delay capacitor to VREF assures correct logic at power up. Figure 8. OV and UV Comparators on the UC1903 Start Latch and Supply Under-Voltage Sense Allow Predictable Power-Up At power-Up, while the +VIN input supply is below 3 V, all open collector outputs are off. With +VIN greater than 3 V the POWER OK output will be driven low and the UV OV FAULT outputs are disabled. Once +VIN rises above the VSUV threshold of 7 V the fault outputs will be enabled. As would be expected, the SENSE 1-4 voltages at power up may be below the UVFAULT window and the UVFAULT output may be driven low. 10 Submit Documentation Feedback Copyright (c) 1999-2008, Texas Instruments Incorporated Product Folder Link(s): UC1903 UC2903 UC3903 PACKAGE OPTION ADDENDUM www.ti.com 9-May-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) (Requires Login) 5962-88697012A ACTIVE LCCC FK 20 1 TBD Call TI Call TI 5962-8869701VA ACTIVE CDIP J 18 1 TBD Call TI Call TI UC1903J ACTIVE CDIP J 18 1 TBD A42 N / A for Pkg Type UC1903J883B ACTIVE CDIP J 18 1 TBD A42 N / A for Pkg Type UC1903L ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type UC1903L883B ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type UC2903DW ACTIVE SOIC DW 18 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2903DWG4 ACTIVE SOIC DW 18 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2903DWTR ACTIVE SOIC DW 18 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2903DWTRG4 ACTIVE SOIC DW 18 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2903J ACTIVE CDIP J 18 1 TBD UC2903N ACTIVE PDIP N 18 20 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC2903NG4 ACTIVE PDIP N 18 20 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC2903Q ACTIVE PLCC FN 20 46 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR UC2903QG3 ACTIVE PLCC FN 20 46 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR UC3903DW ACTIVE SOIC DW 18 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3903DWG4 ACTIVE SOIC DW 18 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3903DWTR ACTIVE SOIC DW 18 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3903DWTRG4 ACTIVE SOIC DW 18 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3903J ACTIVE CDIP J 18 1 TBD Addendum-Page 1 A42 A42 Samples N / A for Pkg Type N / A for Pkg Type PACKAGE OPTION ADDENDUM www.ti.com 9-May-2012 Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) UC3903N ACTIVE PDIP N 18 20 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3903NG4 ACTIVE PDIP N 18 20 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3903Q ACTIVE PLCC FN 20 46 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR UC3903QG3 ACTIVE PLCC FN 20 46 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF UC1903, UC2903, UC2903M, UC3903, UC3903M : * Catalog: UC3903, UC2903, UC3903M, UC3903 Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 9-May-2012 * Military: UC2903M, UC1903, UC1903 NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Military - QML certified for Military and Defense Applications Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant UC2903DWTR SOIC DW 18 2000 330.0 24.4 10.9 12.0 2.7 12.0 24.0 Q1 UC3903DWTR SOIC DW 18 2000 330.0 24.4 10.9 12.0 2.7 12.0 24.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) UC2903DWTR SOIC DW 18 2000 367.0 367.0 45.0 UC3903DWTR SOIC DW 18 2000 367.0 367.0 45.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated