Order this document by MJD2955/D SEMICONDUCTOR TECHNICAL DATA DPAK For Surface Mount Applications Designed for general purpose amplifier and low speed switching applications. * * * * * * Lead Formed for Surface Mount Applications in Plastic Sleeves (No Suffix) Straight Lead Version in Plastic Sleeves ("-1" Suffix) Lead Formed Version Available in 16 mm Tape and Reel ("T4" Suffix) Electrically Similar to MJE2955 and MJE3055 DC Current Gain Specified to 10 Amperes High Current Gain-Bandwidth Product -- fT = 2.0 MHz (Min) @ IC = 500 mAdc IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIII IIIII IIIII III IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIII IIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIII IIIII IIIII III IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIII IIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIII IIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII SILICON POWER TRANSISTORS 10 AMPERES 60 VOLTS 20 WATTS MAXIMUM RATINGS Collector-Emitter Voltage Symbol Value Unit VCEO 60 Vdc Collector-Base Voltage VCB 70 Vdc Emitter-Base Voltage VEB 5 Vdc Collector Current IC 10 Adc Base Current IB 6 Adc Total Power Dissipation @ TC = 25_C Derate above 25_C PD 20 0.16 Watts W/_C Total Power Dissipation (1) @ TA = 25_C Derate above 25_C PD 1.75 0.014 Watts W/_C TJ, Tstg - 55 to + 150 _C Operating and Storage Junction Temperature Range THERMAL CHARACTERISTICS Characteristic Symbol Max Unit Thermal Resistance, Junction to Case RJC 6.25 _C/W Thermal Resistance, Junction to Ambient (1) RJA 71.4 _C/W CASE 369A-13 CASE 369-07 MINIMUM PAD SIZES RECOMMENDED FOR SURFACE MOUNTED APPLICATIONS 0.190 4.826 Rating 0.243 6.172 0.063 1.6 0.118 3.0 0.07 1.8 0.165 4.191 (1) These ratings are applicable when surface mounted on the minimum pad sizes recommended. Safe Area Curves are indicated by Figure 1. Both limits are applicable and must be observed. inches mm REV 1 Motorola, Inc. 1995 Motorola Bipolar Power Transistor Device Data 1 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIII IIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIII IIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIII IIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIII IIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIII IIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIII IIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII v v IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII ELECTRICAL CHARACTERISTICS (TC = 25_C unless otherwise noted) Characteristic Symbol Min Max Unit VCEO(sus) 60 -- Vdc Collector Cutoff Current (VCE = 30 Vdc, IB = 0) ICEO -- 50 Adc Collector Cutoff Current (VCE = 70 Vdc, VEB(off) = 1.5 Vdc) (VCE = 70 Vdc, VEB(off) = 1.5 Vdc, TC = 150_C) ICEX -- -- 0.02 2 Collector Cutoff Current (VCB = 70 Vdc, IE = 0) (VCB = 70 Vdc, IE = 0, TC = 150_C) ICBO -- -- 0.02 2 Emitter Cutoff Current (VBE = 5 Vdc, IC = 0) IEBO -- 0.5 20 5 100 -- -- -- 1.1 8 OFF CHARACTERISTICS Collector-Emitter Sustaining Voltage (1) (IC = 30 mAdc, IB = 0) mAdc mAdc mAdc ON CHARACTERISTICS DC Current Gain (1) (IC = 4 Adc, VCE = 4 Vdc) (IC = 10 Adc, VCE = 4 Vdc) hFE -- Collector-Emitter Saturation Voltage (1) (IC = 4 Adc, IB = 0.4 Adc) (IC = 10 Adc, IB = 3.3 Adc) VCE(sat) Vdc Base-Emitter On Voltage (1) (IC = 4 Adc, VCE = 4 Vdc) VBE(on) -- 1.8 Vdc fT 2 -- MHz DYNAMIC CHARACTERISTICS Current-Gain -- Bandwidth Product (IC = 500 mAdc, VCE = 10 Vdc, f = 500 kHz) (1) Pulse Test: Pulse Width 2 300 s, Duty Cycle 2%. Motorola Bipolar Power Transistor Device Data TYPICAL CHARACTERISTICS PD, POWER DISSIPATION (WATTS) TA TC 2.5 25 2 20 TC 1.5 15 TA SURFACE MOUNT 1 10 0.5 5 0 0 50 25 75 100 125 150 T, TEMPERATURE (C) Figure 1. Power Derating 500 100 2 VCE = 2 V 0.7 0.5 25C - 55C 50 30 20 0.02 0.05 0.1 0.5 0.2 1 2 5 10 0 0.1 0.2 0.4 0.6 1 2 Figure 2. DC Current Gain Figure 3. Turn-On Time 4 6 5 TJ = 25C VCC = 30 V IC/IB = 10 IB1 = IB2 3 2 TJ = 25C 1 VBE(sat) @ IC/IB = 10 VBE @ VCE = 2 V 0.4 0.2 0.06 0.1 IC, COLLECTOR CURRENT (AMP) t, TIME ( s) V, VOLTAGE (VOLTS) 0.6 td @ VBE(off) 5 V IC, COLLECTOR CURRENT (AMP) 1 0.8 0.1 0.03 0.02 1.4 1.2 tr 0.3 0.2 0.07 0.05 10 5 0.01 TJ = 25C VCC = 30 V IC/IB = 10 1 TJ = 150C t, TIME ( s) hFE, DC CURRENT GAIN 300 200 ts 0.7 0.5 0.3 0.2 tf 0.1 VCE(sat) @ IC/IB = 10 0.2 0.3 0.5 1 2 3 5 10 0.07 0.05 0.06 0.1 0.2 0.4 0.6 1 IC, COLLECTOR CURRENT (AMP) IC, COLLECTOR CURRENT (AMP) Figure 4. "On" Voltages, MJD3055 Figure 5. Turn-Off Time Motorola Bipolar Power Transistor Device Data 2 4 6 3 2 TJ = 25C 1.6 V, VOLTAGE (VOLTS) VCC + 30 V 25 s RC +11 V 0 1.2 SCOPE RB -9 V VBE(sat) @ IC/IB = 10 0.8 VBE @ VCE = 3 V D1 51 tr, tf 10 ns DUTY CYCLE = 1% -4 V 0.4 RB and RC VARIED TO OBTAIN DESIRED CURRENT LEVELS D1 MUST BE FAST RECOVERY TYPE, eg: 1N5825 USED ABOVE IB 100 mA MSD6100 USED BELOW IB 100 mA VCE(sat) @ IC/IB = 10 0 0.1 0.2 0.3 0.5 1 2 3 IC, COLLECTOR CURRENT (AMP) 5 10 Figure 6. "On" Voltages, MJD2955 r(t), EFFECTIVE TRANSIENT THERMAL RESISTANCE (NORMALIZED) 1 0.7 0.5 Figure 7. Switching Time Test Ciruit D = 0.5 0.3 0.2 0.2 0.1 0.07 0.05 0.05 0.02 0.01 0.03 0.02 P(pk) RJC(t) = r(t) RJC RJC = 6.25C/W MAX D CURVES APPLY FOR POWER PULSE TRAIN SHOWN READ TIME AT t1 TJ(pk) - TC = P(pk) JC(t) 0.1 t1 t2 DUTY CYCLE, D = t1/t2 SINGLE PULSE 0.01 0.01 0.02 0.03 0.05 0.1 0.2 0.3 0.5 1 2 3 5 t, TIME (ms) 10 20 30 50 100 200 300 500 1k Figure 8. Thermal Response IC, COLLECTOR CURRENT (AMP) 10 5 3 2 TJ = 150C 1 500 s 100 s 1 ms 0.5 0.3 5 ms 0.1 dc WIRE BOND LIMIT THERMAL LIMIT TC = 25C (D = 0.1) SECOND BREAKDOWN LIMIT 0.05 0.03 0.02 0.01 0.6 FORWARD BIAS SAFE OPERATING AREA INFORMATION 1 4 6 10 2 20 40 VCE, COLLECTOR-EMITTER VOLTAGE (VOLTS) There are two limitations on the power handling ability of a transistor: average junction temperature and second breakdown. Safe operating area curves indicate IC - VCE limits of the transistor that must be observed for reliable operation; i.e., the transistor must not be subjected to greater dissipation than the curves indicate. The data of Figure 9 is based on T J(pk) = 150_C; TC is variable depending on conditions. Second breakdown pulse limits are valid for duty cycles to 10% provided T J(pk) 150_C. T J(pk) may be calculated from the data in Figure 8. At high case temperatures, thermal limitations will reduce the power that can be handled to values less than the limitations imposed by second breakdown. v 60 Figure 9. Maximum Forward Bias Safe Operating Area 4 Motorola Bipolar Power Transistor Device Data PACKAGE DIMENSIONS C B V NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. SEATING PLANE -T- E R 4 Z A S 1 2 DIM A B C D E F G H J K L R S U V Z 3 U K F J L H D G 2 PL 0.13 (0.005) M T INCHES MIN MAX 0.235 0.250 0.250 0.265 0.086 0.094 0.027 0.035 0.033 0.040 0.037 0.047 0.180 BSC 0.034 0.040 0.018 0.023 0.102 0.114 0.090 BSC 0.175 0.215 0.020 0.050 0.020 --- 0.030 0.050 0.138 --- STYLE 1: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 5.97 6.35 6.35 6.73 2.19 2.38 0.69 0.88 0.84 1.01 0.94 1.19 4.58 BSC 0.87 1.01 0.46 0.58 2.60 2.89 2.29 BSC 4.45 5.46 0.51 1.27 0.51 --- 0.77 1.27 3.51 --- BASE COLLECTOR EMITTER COLLECTOR CASE 369A-13 ISSUE W C B V E R 4 A 1 2 3 S -T- K SEATING PLANE J F H D G 3 PL 0.13 (0.005) M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. DIM A B C D E F G H J K R S V INCHES MIN MAX 0.235 0.250 0.250 0.265 0.086 0.094 0.027 0.035 0.033 0.040 0.037 0.047 0.090 BSC 0.034 0.040 0.018 0.023 0.350 0.380 0.175 0.215 0.050 0.090 0.030 0.050 STYLE 1: PIN 1. 2. 3. 4. T MILLIMETERS MIN MAX 5.97 6.35 6.35 6.73 2.19 2.38 0.69 0.88 0.84 1.01 0.94 1.19 2.29 BSC 0.87 1.01 0.46 0.58 8.89 9.65 4.45 5.46 1.27 2.28 0.77 1.27 BASE COLLECTOR EMITTER COLLECTOR CASE 369-07 ISSUE K Motorola Bipolar Power Transistor Device Data 5 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, Toshikatsu Otsuki, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-3521-8315 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE (602) 244-6609 INTERNET: http://Design-NET.com HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 6 Motorola Bipolar Power Transistor Device Data *MJD2955/D* MJD2955/D