MA Series Multilayer Ceramic Chip Capacitors MERITEK FEATURES AND APPLICATIONS Dielectric x COG x (NPO) x x x X7R/X5R x x x Y5V x Features Ultra-stable Low dissipation factor Tight tolerance available Good frequency performance No aging of capacitance Semi-stable high K High volumetric efficiency Highly reliable in high temperature applications High insulation resistance x x x Highest volumetric efficiency Non-polar construction General purpose, high K x x x Applications LC and RC tuned circuit Filtering Timing x x x x x x x x x Blocking Coupling Timing Bypassing Frequency discriminating Filtering Bypassing Decoupling Filtering PART NUMBERING SYSTEM MA 1206 XR 103 K 500 Meritek Series Size Dielectric CODE CG COG (NPO) XR X7R XF X5R YV Y5V 101 100 0.1 -- 223 22000 22 0.022 104 100000 100 0.1 Capacitance CODE pF nF F 8R2 8.2 --- Tolerance CODE Tolerance CODE Tolerance B .1pF C .25pF F 1% G 2% K 10% M 20% For values less than 10 pF C or D tolerance preferred CODE D J Z Tolerance .5pF 5% +80/-20% Rated Voltage 2 significant digits + number of zeros. Code 250 500 101 25V 50V 100V 251 250V 501 500V 102 1000V EIA CASE SIZE 0201 Length (L) 0.6 0.03 Width (W) 0.3 0.03 Max. Thickness (T) 0.30 Termination Width (E) 0.15 0.05 0.60 0.2 0.1 1.0 0.4 0.2 0402 202 2000V 302 3000V 0603 0805 1206 1.0 0.05 1.6 0.15 2.0 0.2 3.2 0.2 3.2 0.3 4.5 0.3 5.7 0.4 0.5 0.05 0.8 0.15 1.25 0.2 1.6 0.12 2.5 0.3 3.2 0.3 6.35 0.25 Specifications are subject to change without notice. 1.30 0.5 0.2 1.50 0.6 0.2 1210 1812 2225 1.70 1.70 1.78 0.75 0.25 0.75 0.25 0.75 0.25 rev.6 MA Series Mutilayer Ceramic Chip Capacitors MERITEK PERFORMANCE SPECIFICATION 1. ELECTRICAL EIA NPO *2 over -30oC to +85oC -55oC to +125oC -55oC to +125oC -30 C to +85oC 1MHz, 1Vrms, C < 1000pF 1KHz, 1Vrms 1KHz, 10Vrms Capacitance and D.F. 1 KHz, 1 Vrms, C>1000pF Dissipation Factor (D.F.) < 0.1% for C >30pF and Tangent of Loss Angle (tan) C +22/-82% maximum over -55oC to +125oC < 100% /(400+20C) for C<30pF < 2.5% at > 50V rated o < 5% at 50V rated < 3.5% at 16V, 25V rated < 7% at 16V, 25V rated < 5.0% at 6.3V, 10V rated < 10 % at 6.3V, 10V rated 10G or 10G or < Measuring Conditions for C 15% maximum 0 +120/-40 ppm/ oC, C <20pF < Operating Temperature Range 0 30ppm/ oC , C>20pF Y5V 100M F < Temperature Characteristics *1 X7R < DIELECTRIC CODE 100M F Insulation Resistance (I.R.) after < 100G or < 1000M 60 secs. charging at rated whichever is less whichever is less whichever is less Voltage Proof, 25 oC, 1-5 secs. 2.5 x Rated Voltage 2.5 x Rated Voltage 2.5 x Rated Voltage Capacitance Aging 0 F voltage, 25oC, 55% RH max. ~2.5% per decade hour ~ 7% per decade hour ~ ~ *1 Class II (X7R, Z5U, Y5V) capacitors shall be made a special pre-conditioning before a test or a sequence of tests under the following conditions: Exposure at 150 10oC for 1 hr, followed by setting the capacitor at room temperature for 24 1 hr. *2 Capacitance is within specified tolerance; measured 1000 hours after date of manufacture because of capacitance aging of Class II capacitor. 2. ENVIRONMENTAL Rapid Change of Temperature Endurance (Life Test) Humidity Test (Damp heat, steady state) *1 *2 *3 *4 Post-Test Inspection Requirements At least 75% of termination area should be well tinned No visible damage IEC 384-10 4.12 /JIS C 5102 9.3 -55oC to +125oC, 5 cycles (NPO, X7R) Duration: 30 mins. Recovery: 6 to 24 hrs. (NPO) 24 2 hrs. (X7R) No visible damage IEC 384-10 4.15 1000 hrs. at maximum temperature with x 1.5 rated voltage applied Recovery: 6 to 24 hrs. (NPO) 24 2 hrs. (X7R, Y5V) IEC 384-10 4.14 /JIS C 5102 9.5 500 hrs. at 40 2oC, 90-95% RH Recovery: 6 to 24 hrs. (NPO) 24 2 hrs. (X7R, Y5V) At least 75% of termination should be covered by solder No visible damage NPO X7R < 0.5% or 0.5pF < +10/-5% C/C whichever is greater Y5V < +20/-10% X7R NPO C/C < 1% or 1pF < 10% whichever is greater < 1.5 x initial requirement D.F I.R 0.25 x initial requirement No visible damage NPO X7R < 2 0% C/C < 2% or 1pF whichever is greater < 2.0 x initial requirement <1.5 x initial requirement D.F. I.R. 0.25 x initial requirement No visible damage X7R NPO < 10% C/ C < 2% or 1pF whichever is greater < 2.0 x initial requirement <1.5 x initial requirement D.F. I.R. 0.25 x initial requirement No visible damage < Adhesion Y5V < 30% < Resistance to Soldering Heat Test Conditions IEC 384-10 4.11 /JIS C 5102 8.13 Solder 60 Sn/40 Pb, 235 5oC Immersed for 5 secs. IEC 384-10 4.10 /JIS C 5102 8.14 Immersed in solder bath at 260 5oC for 10 1 secs. Recovery: 6 to 24 hrs. (NPO) 24 2 hrs. (X7R, Y5V) < Test Solderability IEC 384-10 4.8 /JIS C 5102 8.11.2 Capacitors mounted on a substrate, a force of 5N applied perpendicular to the plane of substrate and parallel to the line joining the center of terminations for 10 1 secs. *1-4 Class II (X7R,Y5V) capacitors shall be made a special pre-conditioning before a test or a sequence of tests under the following conditions: Exposure at 150 10oC for 1 hr, followed by setting the capacitor at room temperature for 24 1 hr. Y5V < 30% Multilayer Ceramic Chip Capacitors Product Information MERITEK MLCC Product Information Application General Purpose High Capacitance Series MA MA Dielectric Size Capacitance Rated voltage NPO 0201,0402, 0603,0805,1206, 1210, 1812 0.5pF ~ 0.039F X7R 0201,0402, 0603,0805,1206, 1210, 1812 100pF ~ 1F 10V, 16V, 25V, 50V, 100V 16V, 25V, 50V, 100V Y5V 0402, 0603,0805,1206, 1210, 1812 0.01uF ~ 1F 10V, 16V, 25V, 50V, 100V X7R 0402, 0603,0805,1206, 1210, 1812 0.1uF ~ 22F 6.3V, 10V, 16V, 25V, 50V X5R 0201,0402, 0603,0805,1206 0.027uF ~ 10F Y5V 0402, 0603,0805,1206, 1210, 1812 0.15uF ~ 47F 6.3V, 10V, 16V 6.3V, 10V, 16V, 25V, 35V, 50V Low Inductance MA X7R 0612 0.01uF ~ 0.15F 50V High Q & Low ESR HQ NPO 0402, 0603,0805 0.5pF ~ 3300F 16V, 25V, 50V, 100V Open-mode Design OP High Voltage Capacitor Arrays Safety capacitors (X2/Y3) X7R 0805,1206, 1210, 1812 100pF ~ 1F NPO 0805,1206, 1210, 1808, 1812 10pF ~ 6800pF 200V, 250V, 500V, 630V, 1kV, 2kV, 3kV X7R 0805,1206, 1210, 1808, 1812 100pF ~ 0.1F 200V, 250V, 500V, 630V, 1kV, 1.5kV, 2kV, 3kV Y5V 0805,1206, 1210, 1812 0.01uF ~ 0.68F NPO 0612 (4 x 0603) 10pF ~ 470pF 50V CI X7R 0612 (4 x 0603) 680pF ~ 0.1F 16V,25V,50V Y5V 0612 (4 x 0603) 0.022uF ~ 0.15F 16V,25V,50V MSC NPO 1808 5pF ~ 680pF 250Vac X7R 1808 150pF ~ 1500pF 250Vac HC 100V, 200V, 250V, 500V 200V, 250V Multilayer Ceramic Capacitors MA Low Inductance Series FEATURES * * * Reversed geometry termination type Low ESL, low ESR Noise reduction for high frequency PART NUMBER SYSTEM MA 0612 XR 103 Meritek Series Size Dielectric XR X7R CODE Capacitance Expressed in picofarads. First 2 digits are significant digits. Third digit denotes number of zeros to follow. Use R for decimal point for values less than 10pF. CODE 103 124 F 0.01 0.12 Tolerance CODE B C .10pF .25pF For values less than 10 pF use C or D D .50pF G 2% J 5% Rated Voltage 2 significant digits + number of zeros. CODE 250 500 25V 50V X7R CAPACITANCE RANGE CHART EIA CASE SIZE 0612 Working Voltage 50 Cap (F) 0.010 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 Some special values available upon request K 500 MERITEK