Analog and Interface Product Selector Guide
Thermal Management
Motor Drivers
Interface Peripherals
Power Management
Linear & Mixed-Signal
Safety & Security
www.microchip.com/analog
Analog and Interface Product Solutions
Fall 2011
Table of Contents
2 Analog and Interface Product Selector Guide
Thermal Management
Temperature Sensors ............................................ 4
Logic Output Temperature Sensors .................... 4
Voltage Output Temperature Sensors ................. 4
Serial Output Temperature Sensors ................... 4
Brushless DC Fan Controllers and
Fan Fault Detectors ............................................... 5
Motor Drivers
Stepper Motors, DC Motors and 3 Phase
BLDC Fan Controllers ............................................ 5
Power Management
Voltage References ............................................... 6
Linear Regulators
50-250 mA LDO Linear Regulators .................... 6
300 mA LDO Linear Regulators ......................... 7
500-800 mA LDO Linear Regulators .................. 7
1A and > LDO Linear Regulators ....................... 8
Application Specific LDO Linear Regulators ........ 8
LDO Regulator Combination Products ..................... 8
Switching Regulators ............................................. 9
Switching Regulator Combination Products .............. 9
PWM Controllers ................................................... 9
Charge Pump DC-to-DC Converters ....................... 10
Inverting or Doubling Charge Pumps ................ 10
Inverting and Doubling Charge Pumps ............. 10
Regulated Charge Pumps ................................ 10
CPU/System Supervisors .................................... 10
Voltage Detectors ................................................ 11
Power MOSFET Drivers ........................................ 12
Low-Side Drivers, 0.5A to 1.2A Peak
Output Current ............................................... 12
Low-Side Drivers, 1.5A Peak Output Current ..... 12
Low-Side Drivers, 2.0A to 12.0A Peak
Output Current ............................................... 13
High-Side/Low-Side Drivers ............................. 13
Synchronous Buck High-Side Drivers ................ 13
Battery Chargers ................................................. 14
Hot Swap Controllers ........................................... 14
Linear
Op Amps ............................................................ 15
High Precision Operational Amplifiers ................... 18
Chopper Stabilized ......................................... 18
Auto-Zero ....................................................... 18
Programmable Gain Amplifiers (PGA) .................... 18
Selectable Gain Amplifiers (SGA) .......................... 18
Comparators ....................................................... 19
Mixed Signal
Successive Approximation Register (SAR)
A/D Converters ................................................... 19
Delta-Sigma A/D Converters ................................ 20
Energy Measurement ICs ..................................... 20
Dual-Slope A/D Converters .................................. 20
Binary and BCD A/D Converters ........................... 21
Display A/D Converters ....................................... 21
Digital Potentiometers ......................................... 21
Frequency-to-Voltage/Voltage-to-Frequency
Conver ters .......................................................... 23
D/A Converters ................................................... 23
Interface
Controller Area Network (CAN) Products ................ 24
Infrared Products................................................. 24
Ethernet Products ............................................... 24
Passive Access Products ..................................... 24
LIN Transceiver Products ...................................... 25
Serial Peripherals ................................................ 25
IEEE 802.15.4 ZigBee® RF Transceiver Products ... 25
Stand-alone RF Receiver Products ........................ 25
USB Products ..................................................... 25
Safety & Security
Photoelectric Smoke Detector ICs ........................ 26
Ionization Smoke Detector ICs ............................. 26
Ionization Smoke Detector Front Ends .................. 26
Piezoelectric Horn Drivers .................................... 26
Analog Design and Development Tools
Thermal Management .......................................... 27
Mixed Signal ....................................................... 27
Power Management ............................................. 28
Interface ............................................................. 29
Linear ................................................................. 30
Analog Blank Evaluation Boards ........................... 30
Miscellaneous Analog Demonstration
and Evaluation Tools ........................................... 30
Featured Analog Development Tools
Thermal Management .......................................... 31
Mixed Signal ....................................................... 31
Power Management ............................................. 31
Interface ............................................................. 32
Linear ................................................................. 32
Part Number Designations
Analog Products with “TC” Prefix .......................... 33
Analog Products with “MCP” Prefix ....................... 34
Analog Products with “RE46C” Prefix .................... 35
Need Additional Support and Resources?
Microchip is committed to supporting its customers by
helping design engineers develop products faster and more
efficiently. Customers can access three main service areas at
www.microchip.com. The Support area provides a fast way to
get questions answered. The Sample area offers evaluation
samples of any Microchip device. microchipDIRECT provides
24-hour pricing, ordering, inventory and credit for convenient
purchasing of all Microchip devices and development tools.
This site also features online programming capabilities.
Finally, the Training area offers opportunities to expand your
knowledge with Microchip’s online web seminars and hands-
on courses at our worldwide Technical Training Centers.
Our seminars and training classes are designed to fit your
schedule and offer an overview of many product, development
tool and application topics. Visit www.microchip.com/training
for class content and schedules.
Have you ever encountered a technical dilemma at a critical
point in your design development and your supplier was not
available to answer your questions? Microchip’s first ever
24/7 global technical support line brings technical support
resources any time help is needed. Because some technical
problems require hands-on assistance in order to be resolved
quickly, Microchip has also developed a global team of field
applications engineers and field sales engineers for local
assistance.
Microchip’s integrated analog technology,
peripherals and features are engineered
to meet today’s demanding design
requirements. Our broad spectrum of
analog products addresses thermal
management, power management,
battery management, mixed-signal, linear,
interface and safety & security solutions.
Combined with “Intelligent Analog”
microcontrollers, Microchip offers an
extensive analog portfolio for thousands
of high-performance design applications
in the automotive, communications
(wireless), consumer, computing and
industrial control markets.
Our broad portfolio of stand-alone
analog and interface devices offers
highly integrated solutions that combine
various analog functions in space-saving
packages and support a variety of
bus interfaces. Many of these devices
support functionality that enhances the
analog features currently available on PIC®microcontrollers.
Want a Business Partner,
Not Just a Vendor?
Successful companies recognize the value of a strategic
supplier relationship to help them deliver innovative products
to their markets in a timely manner. They trust their suppliers
to furnish quality components for current design opportunities
as well as provide technology road maps and innovative
solutions to stay ahead of tomorrow’s design trends.
Microchip Technology provides low-risk product development,
lower total system cost and faster time to market to more
than 45,000 of these successful companies worldwide.
Headquartered in Chandler, Arizona, Microchip offers
outstanding technical support along with dependable delivery
and quality.
Founded in 1989, Microchip’s business model is based on
a series of guiding values that aim to establish successful
customer partnerships by exceeding expectations for
products, services and attitude. Continuous improvement,
technology innovation and the pursuit of the highest quality
possible drive Microchip’s company culture.
The result is a worldwide organization dedicated to delivering
whole product solutions which include high performance
silicon devices, easy-to-use development tools, outstanding
technical support and sophisticated technical documentation.
Are Quality and Delivery a Concern?
Microchip’s quality systems are certified according to
the International Organization for Standards/Technical
Specification (ISO/TS)-16949:2002 requirements. This
demonstrates that the Company’s quality systems meet
the most stringent industry quality-management system
standards, resulting in high-quality semiconductor products.
Direct control over manufacturing resources allows shortened
design and production cycles. By owning the wafer fabrication
facilities and the majority of the test and assembly
operations, and by employing proprietary statistical process
control techniques, Microchip has been able to achieve and
maintain high production yields.
Are you Looking for Complete
Analog & Interface Design Solutions?
Microchip Technology’s Stand-Alone Analog & Interface Portfolio
Power
Management
LDO & Switching
Regulators
Charge Pump
DC/DC Converters
Power MOSFET
Drivers
PWM Controllers
System Supervisors
Voltage Detectors
Voltage References
Li-Ion/Li-Polymer
Battery Chargers
Mixed-Signal
A/D Converter
Families
Digital
Potentiometers
D/A Converters
V/F and F/V
Converters
Energy
Measurement
ICs
Interface
CAN Peripherals
Infrared
Peripherals
LIN Transceivers
Serial Peripherals
Ethernet Controllers
USB Peripheral
Linear
Op Amps
Programmable
Gain
Amplifiers
Comparators
Safety & Security
Photoelectric
Smoke Detectors
Ionization Smoke
Detectors
Ionization Smoke
Detector Front Ends
Piezoelectric
Horn Drivers
Thermal
Management
Temperature
Sensors
Fan Speed
Controllers/
Fan Fault
Detectors
Motor Drive
Stepper and DC
3Ф Brushless
DC Fan Controller
Analog and Interface Product Selector Guide 3
Analog and Interface Product Selector Guide 4
THERMAL MANAGEMENT
THERMAL MANAGEMENT PRODUCTS – Temperature Sensors
Part # Typical
Accuracy
(°C)
Maximum
Accuracy
@ 25°C (°C)
Maximum
Temperature
Range (°C) Vcc Range
(V) Maximum
Supply
Current (μA) Features Packages
Logic Output Temperature Sensors
TC6501 ±0.5 ±3 -55 to +125 +2.7 to +5.5 40 Cross to MAX6501, Open-drain 5-pin SOT-23A
TC6502 ±0.5 ±3 -55 to +125 +2.7 to +5.5 40 Cross to MAX6502, Push-pull 5-pin SOT-23A
TC6503 ±0.5 ±3 -55 to +125 +2.7 to +5.5 40 Cross to MAX6503, Open-drain 5-pin SOT-23A
TC6504 ±0.5 ±3 -55 to +125 +2.7 to +5.5 40 Cross to MAX6504, Push-pull 5-pin SOT-23A
TC620 ±1 ±3 -40 to +125 +4.5 to +18 400 Two resistor-programmable trip points 8-pin PDIP, 8-pin SOIC
TC621 Note 1 Note 1 -40 to +85 +4.5 to +18 400 Requires external thermistor, resistor-programmable trip points 8-pin PDIP, 8-pin SOIC
TC622 ±1 ±5 -40 to +125 +4.5 to +18 600 Dual output, TO-220 for heat sink mounting, resistor-programmable trip points 8-pin PDIP, 8-pin SOIC, 5-pin TO-220
TC623 ±1 ±3 -40 to +125 +2.7 to +4.5 250 Two resistor-programmable trip points 8-pin PDIP, 8-pin SOIC
TC624 ±1 ±5 -40 to +125 +2.7 to +4.5 300 Dual output, resistor-programmable trip points 8-pin PDIP, 8-pin SOIC
MCP9501 ±1 ±4 -40 to +125 +2.7 to +5.5 40 Active-High, Push-Pull Output, Rising Temperature Switch 5-pin SOT-23
MCP9502 ±1 ±4 -40 to +125 +2.7 to +5.5 40 Active-Low, Open Drain Output, Rising Temperature Switch 5-pin SOT-23
MCP9503 ±1 ±4 -40 to +125 +2.7 to +5.5 40 Active-High, Push-Pull Output, Falling Temperature Switch 5-pin SOT-23
MCP9504 ±1 ±4 -40 to +125 +2.7 to +5.5 40 Active-Low, Open Drain Output, Falling Temperature Switch 5-pin SOT-23
MCP9509 ±0.5 NS -40 to +125 +2.7 to +5.5 50 Resistor-programmable temperature switch 5-pin SOT-23
MCP9510 ±0.5 NS -40 to +125 +2.7 to +5.5 80 Resistor-programmable temperature switch 6-pin SOT-23
Voltage Output Temperature Sensors
MCP9700 ±1 ±4 -40 to +125 +2.3 to +5.5 12 Linear Active Thermistor® IC, Temperature slope: 10 mV/°C 3-pin TO-92, 5-pin SC-70, 3-pin SOT-23
MCP9701 ±1 ±4 -10 to +125 +3.1 to +5.5 12 Linear Active Thermistor® IC, Temperature slope: 19.53 mV/°C, cross to MAX6612 3-pin TO-92, 5-pin SC-70, 3-pin SOT-23
MCP9700A ±1 ±2 -40 to +125 +2.3 to +5.5 12 Linear Active Thermistor® IC, Temperature slope: 10 mV/°C 3-pin TO-92, 5-pin SC-70, 3-pin SOT-23
MCP9701A ±1 ±2 -40 to +125 +3.1 to +5.5 12 Linear Active Thermistor® IC, Temperature slope: 19.53 mV/°C, cross to MAX6612 3-pin TO-92, 5-pin SC-70, 3-pin SOT-23
TC1046 ±0.5 ±2 -40 to +125 +2.7 to +4.4 60 High precision temperature-to-voltage converter, 6.25 mV/°C 3-pin SOT-23B
TC1047 ±0.5 ±2 -40 to +125 +2.7 to +4.4 60 High precision temperature-to-voltage converter, 10 mV/°C 3-pin SOT-23B
TC1047A ±0.5 ±2 -40 to +125 +2.5 to +5.5 60 High precision temperature-to-voltage converter, 10 mV/°C 3-pin SOT-23B
Serial Output Temperature Sensors
MCP9800 ±0.5 ±1 -55 to +125 +2.7 to +5.5 400 SMbus/I2C™ compatible interface, 0.0625°C to 0.5°C adj. resolution, Power-saving one-shot
temperature measurement 5-pin SOT-23
MCP9801 ±0.5 ±1 -55 to +125 +2.7 to +5.5 400 SMbus/I2C™ compatible interface, 0.0625°C to 0.5°C adj. resolution, Power-saving one-shot
temperature measurement, multi-drop capability 8-pin MSOP, 8-pin SOIC
MCP9802 ±0.5 ±1 -55 to +125 +2.7 to +5.5 400 SMbus/I2C™ compatible interface with time out, 0.0625°C to 0.5°C adj. resolution, Power-saving
one-shot temperature measurement 5-pin SOT-23
MCP9803 ±0.5 ±1 -55 to +125 +2.7 to +5.5 400 SMbus/I2C™ compatible interface with time out, 0.0625°C to 0.5°C adj. resolution, Power-saving
one-shot temperature measurement, Multi-drop capability 8-pin MSOP, 8-pin SOIC
MCP9804 ±0.25 ±1 -40 to +125 +2.7 to +5.5 400 User programmable temperature limits with alert output, 1°C temp. accuracy from -40°C to +125°C 8-pin MSOP, 8-pin 2x3 DFN
MCP9805 ±0.5 ±1(2) -20 to +125 +3.0 to +3.6 400 JEDEC compatible register set, SMbus/I2C™ compatible interface, Programmable, Shut-down modes
and EVENT output 8-pin TSSOP, 8-pin 2x3 DFN
MCP9843 ±0.5 ±1(2) -20 to +125 +3.0 to +3.6 500 Compliant to JEDEC TS2002 specifi cation 8-pin TSSOP, 8-pin 2x3 DFN, 8-pin 2x3 TDFN
MCP98242 ±0.5 ±1(2) -20 to +125 +3.0 to +3.6 400 Same temperature sensor as MCP9805 plus integrated DDR2 Serial Presence Detect EEPROM 8-pin TSSOP, 8-pin 2x3 DFN
MCP98243 ±1 ±3 -40 to +125 +3.0 to +3.6 500 Serial output temperature sensor with integrated EEPROM 8-pin TSSOP, 8-pin 2x3 DFN, 8-pin 2x3 TDFN
TC77 ±0.5 ±1 -55 to +125 +2.7 to +5.5 400 SPI compatible interface, 0.0625°C temperature resolution 5-pin SOT-23A, 8-pin SOIC
TC72 ±0.5 ±1 -55 to +125 +2.65 to +5.5 400 SPI compatible interface, Power-saving one-shot temperature measurement, 0.25°C temperature
resolution 8-pin MSOP, 8-pin 3x3 DFN
TC74 ±0.5 ±2 -40 to +125 +2.7 to +5.5 350 SMbus/I2C™ compatible interface, 1°C temperature resolution 5-pin SOT-23A, 5-pin TO-220
Note 1: These devices use an external temperature sensor. Accuracy of the total solution is a function of the accuracy of the external sensor.
2: Maximum accuracy measured at 85°C.
Analog and Interface Product Selector Guide 5
THERMAL MANAGEMENT PRODUCTS – Brushless DC Fan Controllers and Fan Fault Detectors
Part # Description Typical
Accuracy
(°C)
Maximum
Accuracy
@ 25°C (°C)
Maximum
Temperature
Range (°C) Vcc Range
(V) Maximum
Supply
Current (μA) Features Packages
TC642 Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 1,000 FanSense™ Fan Monitor, Minimum fan speed control 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
TC642B Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 400 FanSense™ Fan Monitor, Minimum fan speed control, Fan auto-restart 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
TC646 Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 1,000 FanSense™ Fan Monitor, Auto-shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
TC646B Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 400 FanSense™ Fan Monitor, Auto-shutdown, Fan auto-restart 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
TC647 Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 1,000 FanSense™ Fan Monitor, Minimum fan speed control 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
TC647B Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 400 FanSense™ Fan Monitor, Minimum fan speed control, Fan auto-restart 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
TC648 Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 1,000 Overtemperature alert, Auto-shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
TC648B Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 400 Overtemperature alert, Auto-shutdown, Fan auto-restart 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
TC649 Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 1,000 FanSense™ Fan Monitor, Auto-shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
TC649B Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 400 FanSense™ Fan Monitor, Auto-shutdown, Fan auto-restart 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
TC650 Fan Manager ±1 ±3 -40 to +125 +2.8 to +5.5 90 Overtemperature alert 8-pin MSOP
TC651 Fan Manager ±1 ±3 -40 to +125 +2.8 to +5.5 90 Overtemperature alert, Auto-shutdown 8-pin MSOP
TC652 Fan Manager ±1 ±3 -40 to +125 +2.8 to +5.5 90 FanSense™ Fan Monitor, Overtemperature alert 8-pin MSOP
TC653 Fan Manager ±1 ±3 -40 to +125 +2.8 to +5.5 90 FanSense™ Fan Monitor, Overtemperature alert, Auto-shutdown 8-pin MSOP
TC654 Dual SMbus Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 320 FanSense™ Fan Monitor, RPM data 10-pin MSOP
TC655 Dual SMbus Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 320 FanSense™ Fan Monitor, RPM data, Overtemperature alert 10-pin MSOP
TC664 Single SMbus Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 320 FanSense™ Fan Monitor, RPM data 10-pin MSOP
TC665 Single SMbus Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 320 FanSense™ Fan Monitor, RPM data, Overtemperature alert 10-pin MSOP
TC670 Predictive Fan Fault Detector N/A N/A -40 to +85 +3.0 to +5.5 150 FanSense™ Fan Monitor, Programmable threshold 6-pin SOT-23
Note 1: These devices use an external temperature sensor. Accuracy of the total solution is a function of the accuracy of the external sensor.
MOTOR DRIVERS
MOTOR DRIVER PRODUCTS - Stepper Motors, DC Motors and 3 Phase BLDC Fan Controllers
Part # Motor
Type Input
Voltage
Range (V)
Internal/
External
FETs
Output
Current
(mA) Control Scheme Motor
Speed
Output Shutdown
Protection Temperature
Operating
Range (°C) Features Packages
MTS62C19A One Bipolar Stepper
Motor or Two DC
Motors 10.0 to 40.0 Internal 750 Direct PWM Input,
Current Limit Control,
Microstepping No Overtemperature,
Under Voltage -20 to +85 Dual Full Bridge Motor Driver for Stepper Motors,
Pin compatible with Allegro 6219 24-pin SOIC
MTS2916A One Bipolar Stepper
Motor or Two DC
Motors 10.0 to 40.0 Internal 750 Direct PWM Input,
Current Limit Control,
Microstepping No Overtemperature,
Under Voltage -20 to +85 Dual Full Bridge Motor Driver for Stepper Motors,
Pin compatible with Allegro 2916 24-pin SOIC
MTD6501C 3 Phase Brushless
Fan 2.0 to 14.0 Internal 800 Sensorless Sinusoidal Frequency
Generator Short Circuit
Overtemperature,
Motor Lock-up -30 to +95 3-Phase BLDC Sinusoidal Sensorless Fan Motor
Driver, Overcurrent limitation Thermally
Enhanced 8-pin
SOP
MTD6501D 3 Phase Brushless
Fan 2.0 to 14.0 Internal 500 Sensorless Sinusoidal Frequency
Generator Short Circuit
Overtemperature,
Motor Lock-up -30 to +95 3-Phase BLDC Sinusoidal Sensorless Fan Motor
Driver, Overcurrent limitation 10-pin MSOP
MTD6502B 3 Phase Brushless
Fan 2.0 to 5.5 Internal 750 Sensorless Sinusoidal Frequency
Generator Short Circuit
Overtemperature,
Motor Lock-up -40 to +85 3-Phase BLDC Sinusoidal Sensorless Fan Motor
Driver, Direction control, Overcurrent limitation 10-pin TDFN 3x3
Serial Output Temperature Sensors
Part # Typical
Accuracy
(°C)
Maximum
Accuracy
@ 25°C (°C)
Maximum
Temperature
Range (°C) Vcc Range
(V) Maximum
Supply
Current (μA) Features Packages
TCN75A ±0.5 ±2 -40 to +125 +2.7 to +5.5 500 SMbus/I2C™ compatible interface, power-saving one-shot temperature measurement, multi-drop capability,
0.0625°C to 0.5°C adjustable temperature resolution 8-pin MSOP, 8-pin SOIC
TCN75 ±0.5 ±2 -55 to +125 +2.7 to +5.5 1,000(3) SMbus/I2C™ compatible interface, multi-drop capability, interrupt output, 0.5°C temperature resolution 8-pin MSOP, 8-pin SOIC
Note 1: These devices use an external temperature sensor. Accuracy of the total solution is a function of the accuracy of the external sensor.
2: Maximum accuracy measured at 85°C.
3: TCN75 idle current is 250 mA. This device also has a Software Shutdown mode that reduces supply current to <1 A.
Analog and Interface Product Selector Guide 6
POWER MANAGEMENT
POWER MANAGEMENT – Voltage References
Part # Vcc Range
(V) Output Voltage (V) Max. Load
Current (mA) Initial Accuracy
(max.%) Temperature
Coeffi cient (ppm/°C) Maximum Supply
Current (μA @ 25°C) Packages
MCP1525 2.7 to 5.5 2.5 ±2 ±1 50 100 3-pin TO-92, 3-pin SOT-23B
MCP1541 4.3 to 5.5 4.096 ±2 ±1 50 100 3-pin TO-92, 3-pin SOT-23B
POWER MANAGEMENT – Linear Regulators
Part # Max. Input
Voltage (V) Output Voltage (V) Output
Current
(mA)
Junction
Temperature
Range (°C)
Typical
Active
Current (μA)
Typical Dropout
Voltage @ Max.
Iout (mV)
Typical Output
Voltage
Accuracy (%) Features Packages
50 mA to 250 mA Low-Dropout Linear Regulators
TC2014 6.0 1.8, 2.7, 2.8, 3.0, 3.3 50 -40 to +125 55 45 ±0.4 Ceramic output capacitor stable,
Shutdown, Reference bypass input 5-pin SOT-23A
TC1014 6.0 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 50 -40 to +125 50 85 ±0.5 Shutdown, Reference bypass input 5-pin SOT-23A
TC2054 6.0 1.8, 2.7, 2.8, 3.0, 3.3 50 -40 to +125 55 45 ±0.4 Ceramic output capacitor stable,
Shutdown, Error output 5-pin SOT-23A
TC1054 6.0 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 50 -40 to +125 50 85 ±0.5 Shutdown, Error output 5-pin SOT-23A
TC1070 6.0 1.23 VIN 50 -40 to +125 50 85 – Shutdown, Adjustable 5-pin SOT-23A
TC1072 6.0 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 50 -40 to +125 50 85 ±0.5 Shutdown, Reference bypass input,
Error output 6-pin SOT-23A
TC1223 6.0 2.5, 2.7, 2.8, 3.0, 3.3, 3.6, 4.0, 5.0 50 -40 to +125 50 85 ±0.5 Shutdown 5-pin SOT-23A
MCP1790 30 3.0, 3.3, 5.0 70 -40 to +125 70 500 ±0.2 Ceramic output capacitor stable 3-pin SOT-223, 3-pin DDPAK
MCP1791 30 3.0, 3.3, 5.0 70 -40 to +125 70 500 ±0.2 Ceramic output capacitor stable,
Shutdown, Power good 5-pin SOT-223, 5-pin DDPAK
TC1016 6.0 1.8, 2.7, 2.8, 3.0 80 -40 to +125 50 150 ±0.5 Ceramic output capacitor stable,
Shutdown 5-pin SC-70, 5-pin SOT-23A
TC2015 6.0 1.8, 2.5, 2.6, 2.7, 2.8, 2.85, 3.0, 3.3, 5.0 100 -40 to +125 55 90 ±0.4 Ceramic output capacitor stable,
Shutdown, Reference bypass input 5-pin SOT-23A
TC1015 6.0 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 100 -40 to +125 50 180 ±0.5 Shutdown, Reference bypass input 5-pin SOT-23A
TC2055 6.0 1.8, 2.7, 2.8, 3.0, 3.3 100 -40 to +125 55 90 ±0.4 Ceramic output capacitor stable,
Shutdown, Error output 5-pin SOT-23A
TC1055 6.0 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 100 -40 to +125 50 180 ±0.5 Shutdown, Error output 5-pin SOT-23A
TC1071 6.0 1.23 VIN 100 -40 to +125 50 180 – Shutdown, Adjustable 5-pin SOT-23A
TC1073 6.0 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 100 -40 to +125 50 180 ±0.5 Shutdown, Reference bypass input,
Error output 6-pin SOT-23A
TC1224 6.0 2.5, 2.7, 2.8, 3.0, 3.3, 3.6, 4.0, 5.0 100 -40 to +125 50 180 ±0.5 Shutdown 5-pin SOT-23A
TC1188 6.0 1.8, 2.8, 2.84, 3.15 120 -40 to +125 50 130 ±0.5 Shutdown 5-pin SOT-23A
TC1189 6.0 1.8, 2.8, 2.84, 3.15 120 -40 to +125 50 130 ±0.5 Shutdown 5-pin SOT-23A
TC2185 6.0 1.8, 2.7, 2.8, 3.0, 3.3 150 -40 to +125 55 140 ±0.4 Ceramic output capacitor stable,
Shutdown, Reference bypass input 5-pin SOT-23A
TC1185 6.0 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 150 -40 to +125 50 270 ±0.5 Shutdown, Reference bypass input 5-pin SOT-23A
TC2186 6.0 1.8, 2.7, 2.8, 3.0, 3.3 150 -40 to +125 55 140 ±0.4 Ceramic output capacitor stable,
Shutdown, Error output 5-pin SOT-23A
TC1186 6.0 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 150 -40 to +125 50 270 ±0.5 Shutdown, Error output 5-pin SOT-23A
TC1187 6.0 1.23 VIN 150 -40 to +125 50 270 – Shutdown, Adjustable 5-pin SOT-23A
TC1017 6.0 1.8, 2.6, 2.7, 2.8, 2.85, 2.9, 3.3, 3.4 150 -40 to +125 53 285 ±0.5 Ceramic output capacitor stable,
Shutdown 5-pin SOT-23A, 5-pin SC-70
MCP1754 16 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 150 -40 to +125 56 300 ±2 70 dB PSRR 5-pin SOT-23, 5-pin SOT-89,
5-pin SOT-223, 8-pin 2x3 TDFN
MCP1754S 16 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 150 -40 to +125 56 300 ±2 70 dB PSRR 3-pin SOT-23, 3-pin SOT-89,
3-pin SOT-223, 8-pin 2x3 TDFN
Analog and Interface Product Selector Guide 7
POWER MANAGEMENT – Linear Regulators (Continued)
Part # Max. Input
Voltage (V) Output Voltage (V) Output
Current
(mA)
Junction
Temperature
Range (°C)
Typical
Active
Current (μA)
Typical Dropout
Voltage @ Max.
Iout (mV)
Typical Output
Voltage
Accuracy (%) Features Packages
50 mA to 250 mA Low-Dropout Linear Regulators (Continued)
MCP1801 10 0.9, 1.2, 1.8, 2.5, 3.0, 3.3, 5.0, 6.0 150 -40 to +85 25 250 ±0.4 Ceramic output capacitor stable,
Shutdown, High PSRR 5-pin SOT-23A
MCP1804 28 1.8 to 18 150 -40 to +85 50 1300 ±2 Shutdown, High PSRR 5-pin SOT-23, 5-pin SOT-89,
3-pin SOT-89, 3-pin SOT-223
MCP1700 6.0 1.2, 1.8, 2.5, 3.0, 3.3, 5.0 250 -40 to +125 1.6 300 ±0.4 1.0 μF ceramic cap stable,
Short-circuit protection 3-pin TO-92, 3-pin SOT-23A,
3-pin SOT-89
MCP1701A 10 1.8, 2.5, 3.0, 3.3, 5.0 250 -40 to +85 1.6 380 ±0.5 10V max. input voltage 3-pin TO-92, 3-pin SOT-23A,
3-pin SOT-89
MCP1702 13.2 1.2, 1.5, 1.8, 2.5, 2.8, 3.0, 3.3, 4.0, 5.0 250 -40 to +125 2 650 ±0.4 Ceramic output capacitor stable,
Ultra-low ground current, 13.2V VIN max. 3-pin TO-92, 3-pin SOT-23A,
3-pin SOT-89
MCP1703 16 1.2, 1.5, 1.8, 2.5, 2.8, 3.0, 3.3, 4.0, 5.0 250 -40 to +125 2 650 ±0.4 Ceramic output capacitor stable,
Ultra-low ground current, 16V VIN max. 3-pin SOT-23A, 3-pin SOT-89,
3-pin SOT-223
300 mA Low-Dropout Linear Regulators
TC1107 6.0 2.5, 2.7, 2.8, 3.0, 3.3, 5.0 300 -40 to +125 50 240 ±0.5 Shutdown, Reference bypass input 8-pin MSOP, 8-pin SOIC
TC1108 6.0 2.5, 2.7, 2.8, 3.0, 3.3, 5.0 300 -40 to +125 50 240 ±0.5 3-pin SOT-223
TC1173 6.0 2.5, 2.7, 2.8, 3.0, 3.3, 5.0 300 -40 to +125 50 240 ±0.5 Shutdown, Reference bypass input, Error
output 8-pin MSOP, 8-pin SOIC
TC1174 6.0 1.23 VIN 300 -40 to +125 50 240 – Shutdown, Reference bypass input,
Adjustable 8-pin MSOP, 8-pin SOIC
TC1269 6.0 2.5, 2.8, 3.0, 3.3, 5.0 300 -40 to +125 50 240 ±0.5 Shutdown, Reference bypass input 8-pin MSOP
MCP1802 10 0.9, 1.2, 1.8, 2.5, 3.0, 3.3, 5.0, 6.0 300 -40 to +85 25 250 ±0.4 Ceramic output capacitor stable,
Shutdown, High PSRR 5-pin SOT-23A
MCP1824 6.0 Fixed: 0.8, 1.2, 1.8, 2.5, 3.0, 3.3, 5.0
Adjustable: 0.8 to 5.0 300 -40 to +125 120 200 ±0.5 Ceramic output capacitor stable,
Shutdown, Power good 5-pin SOT-223, 5-pin SOT-23
MCP1824S 6.0 0.8, 1.2, 1.8, 2.5, 3.0, 3.3, 5.0 300 -40 to +125 120 200 ±0.5 Ceramic output capacitor stable 3-pin SOT-223
500 mA to 800 mA Low-Dropout Linear Regulators
TC1262 6.0 2.5, 2.8, 3.0, 3.3, 5.0 500 -40 to +125 80 350 ±0.5 Overtemperature protection,
Overcurrent protection 3-pin TO-220, 3-pin DDPAK,
3-pin SOT-223
TC1263 6.0 2.5, 2.8, 3.0, 3.3, 5.0 500 -40 to +125 80 350 ±0.5 Shutdown, Reference bypass input,
Error output 8-pin SOIC, 5-pin TO-220,
5-pin DDPAK
TC1268 6.0 2.5 500 -40 to +125 80 350 ±0.5 Shutdown, Reference bypass input,
Error output 8-pin SOIC
MCP1725 6.0 0.8, 1.2, 1.8, 2.5, 3.0, 3.3, 5.0 500 -40 to +125 120 210 ±0.5 Ceramic output capacitor stable,
Shutdown, CDELAY, Power good 8-pin 2x3 DFN, 8-pin SOIC
MCP1825 6.0 Fixed: 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5
Adjustable: 0.8 to 5.0 500 -40 to +125 120 210 ±0.5 Ceramic output capacitor stable, Shutdown,
Power good 5-pin TO-220, 5-pin DDPAK,
5-pin SOT-223
MCP1825S 6.0 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5 500 -40 to +125 120 210 ±0.5 Ceramic output capacitor stable 3-pin TO-220, 3-pin DDPAK,
3-pin SOT-223
TC1264 6.0 1.8, 2.5, 3.0, 3.3 800 -40 to +125 80 450 ±0.5 Overtemperature protection,
Overcurrent protection 3-pin TO-220, 3-pin DDPAK,
3-pin SOT-223
TC1265 6.0 1.8, 2.5, 3.0, 3.3 800 -40 to +125 80 450 ±0.5 Shutdown, Reference bypass input,
Error output 8-pin SOIC, 5-pin TO-220,
5-pin DDPAK
TC2117 6.0 1.8, 2.5, 3.0, 3.3 800 -40 to +125 80 600 ±0.5 Overtemperature protection,
Overcurrent protection 3-pin SOT-223, 3-pin DDPAK
Analog and Interface Product Selector Guide 8
POWER MANAGEMENT – Low-Dropout Regulator Combination Products
TC1300(1) 6.0 2.5, 2.7, 2.8, 2.85, 3.0, 3.3 300 -40 to +125 80 210 ±0.5 Shutdown, Reference bypass input,
LDO plus Reset output 8-pin MSOP
TC1301A(1) 6.0 LDO1: 1.5-3.3
LDO2: 1.5-3.3 LDO1: 300
LDO2: 150 -40 to +125 103 LDO1: 104
LDO2: 150 ±0.5 Dual LDO plus Reset output, Shutdown,
Reference bypass, Voltage detect 8-pin MSOP, 8-pin 3x3 DFN
TC1301B(1) 6.0 LDO1: 1.5-3.3
LDO2: 1.5-3.3 LDO1: 300
LDO2: 150 -40 to +125 114 LDO1: 104
LDO2: 150 ±0.5 Dual LDO plus Reset, per channel output
shutdown, Reference bypass 8-pin MSOP, 8-pin 3x3 DFN
TC1302A(1) 6.0 LDO1: 1.5-3.3
LDO2: 1.5-3.3 LDO1: 300
LDO2: 150 -40 to +125 103 LDO1: 104
LDO2: 150 ±0.5 Dual LDO, Output shutdown reference
bypass, Voltage detect 8-pin MSOP, 8-pin 3x3 DFN
TC1302B(1) 6.0 LDO1: 1.5-3.3
LDO2: 1.5-3.3 LDO1: 300
LDO2: 150 -40 to +125 114 LDO1: 104
LDO2: 150 ±0.5 Dual LDO, per channel output shutdown,
Reference bypass 8-pin MSOP, 8-pin 3x3 DFN
TC1305 6.0 2.5, 2.8, 3.0 150(1) -40 to +125 120 240 ±0.5 Dual LDO plus Reset output, Reference
bypass input, Shutdown, Select Mode™
selectable output voltages 10-pin MSOP
TC1306 6.0 1.8, 2.8, 3.0 150(1) -40 to +125 120 240 ±0.5 Dual LDO plus Reset output, Shutdown,
Select Mode™ selectable output voltages 8-pin MSOP
TC1307(1) 6.0 1.8, 2.5, 2.8, 3.0 150(1) -40 to +125 220 200 ±0.5 Quad LDO plus Reset output, Shutdown,
Select Mode™ selectable output voltage 16-pin QSOP
Note 1: LDOs with shutdown (except Power Management Combination Products as indicated) have typical shutdown currents of 0.05 mA.
POWER MANAGEMENT – Linear Regulators (Continued)
Part # Max. Input
Voltage (V) Output Voltage (V) Output
Current
(mA)
Junction
Temperature
Range (°C)
Typical
Active
Current (μA)
Typical Dropout
Voltage @ Max.
Iout (mV)
Typical Output
Voltage
Accuracy (%) Features Packages
1A and Above Low-Dropout Linear Regulators
MCP1726 6.0 Fixed: 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5
Adjustable: 0.8 to 5.0 1000 -40 to +125 140 300 ±0.4 Ceramic output capacitor stable, Shutdown,
CDELAY, Power good 8-pin 3x3 DFN, 8-pin SOIC
MCP1826 6.0 Fixed: 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5
Adjustable: 0.8 to 5.0 1000 -40 to +125 140 300 ±0.5 Ceramic output capacitor stable, Shutdown,
Power good 5-pin TO-220, 5-pin DDPAK, 5-pin
SOT-223
MCP1826S 6.0 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5 1000 -40 to +125 140 300 ±0.5 Ceramic output capacitor stable 3-pin TO-220, 3-pin DDPAK, 3-pin
SOT-223
MCP1727 6.0 Fixed: 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5
Adjustable: 0.8 to 5.0 1500 -40 to +125 140 330 ±0.5 Ceramic output capacitor stable, Shutdown,
CDELAY, Power good 8-pin 3x3 DFN, 8-pin SOIC
MCP1827 6.0 Fixed: 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5
Adjustable: 0.8 to 5.0 1500 -40 to +125 140 330 ±0.5 Ceramic output capacitor stable, Shutdown,
Power good 5-pin DDPAK, 5-pin TO-220
MCP1827S 6.0 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5 1500 -40 to +125 140 330 ±0.5 Ceramic output capacitor stable 3-pin DDPAK, 3-pin TO-220
Application Specifi c Low-Dropout Linear Regulators
TC1266 6.0 3.3 200 -5 to +70 230 200 ±1.0 PCI compliant 8-pin SOIC, 8-pin MSOP
TC1267 6.0 3.3 400 -5 to +70 230 300 ±1.0 PCI compliant 5-pin DDPAK
TC57 8 2.5, 3.0, 3.3 4,000(1) -40 to +85 50 100(1) ±2.0 Shutdown, External transistor 5-pin SOT-23A
TC59 -10 -3.0, -5.0 100 -40 to +85 3 380 ±0.5 Negative LDO 3-pin SOT-23A
Note 1: Depending on external transistor confi guration.
Analog and Interface Product Selector Guide 9
POWER MANAGEMENT – Switching Regulators
Part # Description Input
Voltage
Range (V) Output
Voltage (V) Operating
Temperature
Range (°C) Control
Scheme Switching
Frequency
(kHz) Typical Active
Current (μA) Output
Current
(mA) Features Packages
MCP1601 Synchronous Buck Regulator 2.7 to 5.5 0.9V to VIN -40 to +85 PFM/PWM/LDO 750 825 (PWM)
125 (PFM) 500 UVLO, Auto-switching, LDO 8-pin MSOP
MCP1602 Synchronous Buck Regulator 2.7 to 5.5 0.8 to 4.5 -40 to +85 PFM/PWM 2000 35 500 PFM, PWM auto-switching, UVLO, Soft start,
Power good indicator 10-pin MSOP,
10-pin 3x3 DFN
MCP1603 Synchronous Buck Regulator 2.7 to 5.5 0.8 to 4.0 -40 to +85 PFM/PWM 2000 45 500 Overtemperature and Overcurrent protection 5-pin TSOT -23,
8-pin 2x3 DFN
MCP1612 Synchronous Buck Regulator 2.7 to VIN 0.8 to 5.5 -40 to +85 Constant frequency,
PWM 1400 10,000 1000 Overall effi ciency >94%, Soft start,
Overtemperature and Overcurrent protection 8-pin MSOP,
8-pin 3x3 DFN
MCP1623/4 Step-up DC/DC Regulator 0.65 to 6 2.0 to 5.5 -40 to +85 PWM or
PWM/PFM 500 19 175 Integrated synchronous boost regulator, 0.65V
start-up voltage, Soft start, True load disconnect 6-pin SOT-23,
8-pin 2x3 DFN
MCP1640/B/
C/D Step-up DC/DC Regulator 0.65 to 6 2.0 to 5.5 -40 to +85 PWM or
PWM/PFM 500 19 350 Integrated synchronous boost regulator, 0.65V
start-up voltage, Soft start, True load disconnect
or input-to-output bypass option 6-pin SOT-23,
8-pin 2x3 DFN
MCP1650 Step-up DC/DC Controller 2.7 to 5.5 2.5 to ext. tx
limited -40 to +125 Constant frequency, 750 120 560/440 2 duty cycles for min. and max. loads, Shutdown
control, UVLO, Soft start 8-pin MSOP
MCP1651 Step-up DC/DC Controller 2.7 to 5.5 2.5 to ext. tx
limited -40 to +125 Constant frequency,
2 fi xed DC 750 120 560/440 2 duty cycles for min. and max. loads, Shutdown
control, low battery detect, UVLO, Soft start 8-pin MSOP
MCP1652 Step-up DC/DC Controller 2.7 to 5.5 2.5 to ext. tx
limited -40 to +125 Constant frequency,
2 fi xed DC 750 120 560/440 2 duty cycles for min. and max. loads, Shutdown
control, Power good indicator, UVLO, Soft start 8-pin MSOP
MCP1653 Step-up DC/DC Controller 2.7 to 5.5 2.5 to ext. tx
limited -40 to +125 Constant frequency,
2 fi xed DC 750 120 560/440 2 duty cycles for min. and max. loads, Shutdown
control, Low battery detect, Power good indicator,
UVLO, Soft start 10-pin MSOP
MCP16301 30V Input Buck Regulator 4.0 to 30 2.0 to 15 -40 to +85 PWM 500 2000 600 Integrated N-channel, UVLO, Soft start,
Overtemperature protection SOT23-6
TC105 Step-down DC/DC Controller 2.2 to 10 3.0, 3.3, 5.0 -40 to +85 PFM/PWM 300 57 1,000 Low power shutdown mod 5-pin SOT-23A
TC115 Step-up DC/DC Regulator 0.9 to 10 3.0, 3.3, 5.0 -40 to +85 PFM/PWM 100 80 140 Feedback voltage sensing, Low power
shutdown mode 5-pin SOT-89
TC110 Step-up DC/DC Controller 2.0 to 10 3.0, 3.3, 5.0 -40 to +85 PFM/PWM 100/300 50/120 300 Soft start, Low power shutdown mode 5-pin SOT-23A
POWER MANAGEMENT – PWM Controllers
Part # Description Input
Voltage
Range (V)
Operating
Temperature
Range (°C)
Switching
Frequency
(kHz)
Typical
Active
Current (mA) Features Packages
MCP1630 Current mode, high-speed PWM to
use with PIC® MCUs 3.0 to 5.5 -40 to +125 1000 2.8 UVLO, Short circuit and Overtemperature protection,
Integrated MOSFET driver 8-pin MSOP, 8-pin 2x3 DFN
MCP1630V Voltage mode, high-speed PWM to
use with PIC® MCUs 3.0 to 5.5 -40 to +125 1000 2.8 UVLO, Short circuit and Overtemperature protection,
Integrated MOSFET driver 8-pin MSOP, 8-pin 2x3 DFN
MCP1631 Current mode, high-speed PWM to
use with PIC® MCUs 3.0 to 5.5 -40 to +125 2000 3.7 UVLO, Integrated error, current and voltage sense amplifi ers,
Overvoltage comparator and MOSFET driver 20-pin SSOP, 20-pin TSSOP,
20-pin 4x4 QFN
MCP1631HV Current mode, high-speed PWM to
use with PIC® MCUs 3.5 to 16 -40 to +125 2000 3.7 Integrated 16V LDO, UVLO, Integrated error, Ccurrent and voltage
sense amplifi ers, Overvoltage comparator and MOSFET driver 20-pin SSOP, 20-pin TSSOP
MCP1631V Voltage mode, high-speed PWM to
use with PIC® MCUs 3.0 to 5.5 -40 to +125 2000 3.7 UVLO, Integrated error, Current and voltage sense amplifi ers,
Overvoltage comparator and MOSFET driver 20-pin SSOP, 20-pin TSSOP,
20-pin 4x4 QFN
MCP1631VHV Voltage mode, high-speed PWM to
use with PIC® MCUs 3.5 to 16 -40 to +125 2000 3.7 Integrated 16V LDO, UVLO, Integrated error, Current and voltage sense
amplifi ers, Overvoltage comparator and MOSFET driver 20-pin SSOP, 20-pin TSSOP
POWER MANAGEMENT – Switching Regulator Combination Products
TC1303 Synchronous Buck Regulator,
LDO w/Power good 2.7 to 5.5 DC/DC: 0.8 to 4.5
LDO: 1.5 to 3.3 -40 to +85 PFM/PWM 2000 65/600 DC/DC: 500 mA
LDO: 300 mA PFM/PWM auto-switching, Power good output 10-pin MSOP,
10-pin 3x3 DFN
TC1304 Synchronous Buck Regulator,
LDO 2.7 to 5.5 DC/DC: 0.8 to 4.5
LDO: 1.5 to 3.3 -40 to +85 PFM/PWM 2000 65/600 DC/DC: 500 mA
LDO: 300 mA PFM/PWM auto-switching, Power sequencing 10-pin MSOP,
10-pin 3x3 DFN
TC1313 Synchronous Buck Regulator,
LDO 2.7 to 5.5 DC/DC: 0.8 to 4.5
LDO: 1.5 to 3.3 -40 to +85 PFM/PWM 2000 65/600 DC/DC: 500 mA
LDO: 300 mA PFM/PWM auto-switching 10-pin MSOP,
10-pin 3x3 DFN
Analog and Interface Product Selector Guide 10
POWER MANAGEMENT – Charge Pump DC-to-DC Converters
Part # Input
Voltage
Range (V) Output Voltage (V) Operating
Temperature
Range (°C) Maximum Input
Current(1) (μA) Typical Active
Output Current
(mA) Features Packages
Inverting or Doubling Charge Pumps
TC1044S 1.5 to 12 VOUT = -VIN or VOUT = 2 VIN -40 to +85 160 20 85 kHz oscillator, Boost mode 8-pin PDIP, 8-pin SOIC
TC7660 1.5 to 10 VOUT = -VIN or VOUT = 2 VIN -40 to +85 180 20 10 kHz oscillator 8-pin PDIP, 8-pin SOIC
TC7660H 1.5 to 10 VOUT = -VIN or VOUT = 2 VIN -40 to +85 1,000 20 120 kHz oscillator 8-pin PDIP, 8-pin SOIC
TC7660S 1.5 to 12 VOUT = -VIN or VOUT = 2 VIN -40 to +85 160 20 45 kHz oscillator, Boost mode 8-pin PDIP, 8-pin SOIC
TC7662B 1.5 to 15 VOUT = -VIN or VOUT = 2 VIN -40 to +85 180 20 35 kHz oscillator, Boost mode 8-pin PDIP, 8-pin SOIC
TC1240 2.5 to 4.0 VOUT = 2 VIN -40 to +85 900 40 Shutdown, 160 kHz oscillator 6-pin SOT-23A
TC1240A 2.5 to 5.5 VOUT = 2 VIN -40 to +85 900 40 Shutdown, 160 kHz oscillator 6-pin SOT-23A
TC7662A 3.0 to 18 VOUT = -VIN or VOUT = 2 VIN -40 to +85 200 40 12 kHz oscillator 8-pin PDIP, 8-pin SOIC
TC962 3.0 to 18 VOUT = -VIN or VOUT = 2 VIN -40 to +85 200 80 Selectable 12 kHz or 24 kHz oscillator 8-pin PDIP, 16-pin SOIC
Inverting and Doubling Charge Pumps
TC682 2.4 to 5.5 VOUT = -2 VIN -40 to +85 400 10 12 kHz oscillator 8-pin PDIP, 8-pin SOIC
Regulated Charge Pumps
MCP1252 2.1/2.7 to 5.5
2.0 to 5.5 Selectable 3.3V or 5.0V or
Adjustable 1.5V to 5.5V -40 to +85 120 120 mA for VIN>3.0V Power good output, 650 kHz oscillator 8-pin MSOP
MCP1253 2.1/2.7 to 5.5
2.0 to 5.5 Selectable 3.3V or 5.0V or
Adjustable 1.5V to 5.5V -40 to +85 120 120 mA for VIN>3.0V Power good output, 1 MHz oscillator 8-pin MSOP
MCP1256 1.8 to 3.6 3.3 -40 to +85 100 100 Power good, Sleep mode 10-pin MSOP, 10-pin 3x3 DFN
MCP1257 1.8 to 3.6 3.3 -40 to +85 100 100 Sleep mode, Low battery indication 10-pin MSOP, 10-pin 3x3 DFN
MCP1258 1.8 to 3.6 3.3 -40 to +85 100 100 Power good output, Input/output bypass 10-pin MSOP, 10-pin 3x3 DFN
MCP1259 1.8 to 3.6 3.3 -40 to +85 100 100 Low battery indication, Input/output bypass 10-pin MSOP, 10-pin 3x3 DFN
Note 1: Measured at VDD = 5.0V at 25°C and no load.
POWER MANAGEMENT – CPU/System Supervisors
Part # Vcc Range
(V) Operating
Temperature
Range (°C) Nominal Reset Voltage (V) Reset Type Output Typical Reset
Pulse Width
(ms)
Typical
Supply
Current (μA) Additional Features Packages Bond
Options
MCP102 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63, 2.32, 1.9 Active-Low CMOS Push-Pull 120 1 3-pin SOT-23B, 3-pin SC-70, 3-pin TO-92 N/A
MCP103 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63, 2.32, 1.9 Active-Low CMOS Push-Pull 120 1 Max. 809 Pinout 3-pin SOT-23B, 3-pin SC-70, 3-pin TO-92 N/A
MCP121 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63, 2.32, 1.9 Active-Low Open-Drain 120 1 3-pin SOT-23B, 3-pin SC-70, 3-pin TO-92 N/A
MCP131 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63, 2.32, 1.9 Active-Low Open-Drain 120 1 100 k Internal Pull-up
Resistor 3-pin SOT-23B, 3-pin SC-70, 3-pin TO-92 N/A
MCP1319 1.0 to 5.5 -40 to +125 4.6, 2.9(1) Active-Low/High CMOS Push-Pull 200 1 Manual Reset 5-pin SOT-23 N/A
MCP1322 1.0 to 5.5 -40 to +125 4.6, 2.9(1) Active-High Open-Drain/CMOS
Push-Pull 200 1 Manual Reset, two Reset
outputs
(Active-Low Open-Drain,
Active-High Push-Pull) 5-pin SOT-23 N/A
MCP1316 1.0 to 5.5 -40 to +125 4.6, 2.9(1) Active-Low CMOS Push-Pull 200 5 Watchdog Input (WDI),
Time-out = 1.6 sec.,
Manual Reset 5-pin SOT-23 N/A
MCP1317 1.0 to 5.5 -40 to +125 4.6, 2.9(1) Active-High CMOS Push-Pull 200 5 Watchdog Input (WDI),
Time-out = 1.6 sec.,
Manual Reset 5-pin SOT-23 N/A
MCP1318 1.0 to 5.5 -40 to +125 4.6, 2.9(1) Active-Low/High CMOS Push-Pull 200 5 Watchdog Input (WDI),
Time-out = 1.6 sec. 5-pin SOT-23 N/A
Note 1: Other reset voltage options available: 2.0V to 4.7V in 100 mV increments. Contact local Microchip sales offi ce.
Analog and Interface Product Selector Guide 11
POWER MANAGEMENT – CPU/System Supervisors (Continued)
Part # Vcc Range
(V) Operating
Temperature
Range (°C) Nominal Reset Voltage (V) Reset Type Output Typical Reset
Pulse Width
(ms)
Typical
Supply
Current (μA) Additional Features Packages Bond
Options
MCP1320 1.0 to 5.5 -40 to +125 4.6, 2.9(1) Active-Low Open-Drain 200 5 Watchdog Input (WDI),
Time-out = 1.6 sec.,
Manual Reset 5-pin SOT-23 N/A
MCP1321 1.0 to 5.5 -40 to +125 4.6, 2.9(1) Active-Low Open-Drain/CMOS
Push-Pull 200 5
Watchdog Input (WDI),
Time-out = 1.6 sec.,
Manual Reset
(Active-Low Open-Drain,
Active-High Push-Pull)
5-pin SOT-23 N/A
TC1270A 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63 Active-Low CMOS Push-Pull 280 7 Manual Reset 4-pin SOT-143, 5-pin SOT-23 N/A
TC1271A 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63 Active-High CMOS Push-Pull 280 7 Manual Reset 4-pin SOT-143, 5-pin SOT-23 N/A
TC1270AN 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63 Active-Low Open-Drain 0 7 Manual Reset 4-pin SOT-143, 5-pin SOT-23 N/A
TCM809 1.2 to 5.5 -40 to +85 4.63, 4.38, 4.00, 3.08, 2.93, 2.63, 2.32 Active-Low CMOS Push-Pull 240 12 3-pin SOT-23B, 3-pin SC-70 N/A
TCM810 1.2 to 5.5 -40 to +85 4.63, 4.38, 4.00, 3.08, 2.93, 2.63, 2.32 Active-High CMOS Push-Pull 240 12 3-pin SOT-23B, 3-pin SC-70 N/A
MCP100 1.0 to 5.5 -40 to +85 4.72, 4.62, 4.47, 4.37, 3.075, 2.92, 2.62 Active-Low CMOS Push-Pull 350 45 3-pin TO-92, 3-pin SOT-23B D, H
MCP809 1.0 to 5.5 -40 to +85 4.72, 4.62, 4.47, 4.37, 3.075, 2.92, 2.62 Active-Low CMOS Push-Pull 350 45 3-pin SOT-23B N/A
MCP101 1.0 to 5.5 -40 to +85 4.72, 4.62, 4.47, 4.37, 3.075, 2.92, 2.62 Active-High CMOS Push-Pull 350 45 3-pin TO-92, 3-pin SOT-23B D, H
MCP810 1.0 to 5.5 -40 to +85 4.72, 4.62, 4.47, 4.37, 3.075, 2.92, 2.62 Active-High CMOS Push-Pull 350 45 3-pin SOT-23B N/A
MCP120 1.0 to 5.5 -40 to +85 4.72, 4.62, 4.47, 4.37, 3.075, 2.92, 2.62 Active-Low Open-Drain 350 45 3-pin TO-92, 3-pin SOT-23, 8-pin
SOIC D, G, H
MCP130 1.0 to 5.5 -40 to +85 4.72, 4.62, 4.47, 4.37, 3.075, 2.92, 2.62 Active-Low Open-Drain
w/5 kOhm Pull-up 350 45 3-pin TO-92, 3-pin SOT-23, 8-pin
SOIC D, F, H
TC1232 4.5 to 5.5 -40 to +85 4.62, 4.37 Active-Low/High Open-Drain 610 50 Watchdog Timer 8-pin PDIP, 8-pin SOIC,
16-pin SOIC N/A
TC32M 4.5 to 5.5 -40 to +85 4.5 Active-Low Open-Drain 700 50 Watchdog Timer 3-pin TO-92, 3-pin SOT-223 N/A
Note 1: Other reset voltage options available: 2.0V to 4.7V in 100 mV increments. Contact local Microchip sales offi ce.
POWER MANAGEMENT – Voltage Detectors
Part # Vcc Range
(V)
Operating
Temperature
Range (°C) Nominal Reset Voltage (V) Reset Type Output Minimum
Reset Pulse
Width (ms)
Typical
Supply
Current (μA) Features Packages
MCP111 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63, 2.32, 1.90 Active-Low Open-Drain – 1 3-pin SOT-23B, 3-pin TO-92, 3-pin SC-70, 3-pin SOT-89
MCP112 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63, 2.32, 1.90 Active-Low CMOS Push-Pull – 1 3-pin SOT-23B, 3-pin TO-92, 3-pin SC-70, 3-pin SOT-89
TC52 1.5 to 10 -40 to +85 4.5/2.7, 3.0/2.7 Active-Low Open-Drain – 2 Dual channel 5-pin SOT-23A
TC54 0.7 to 10 -40 to +85 4.3, 4.2, 3.0, 2.9, 2.7, 2.1, 1.4 Active-Low CMOS Push-Pull or
Open-Drain – 1 3-pin SOT-23A, 3-pin SOT-89, 3-pin TO-92
Analog and Interface Product Selector Guide 12
POWER MANAGEMENT – Power MOSFET Drivers
Part # Confi guration Operating
Temperature
Range (°C)
Peak Output
Current (A)
Output Resistance
(RH/RL)
(Max. @ 25°C)
Maximum Supply
Voltage (V) Input/Output Delay
(tD1, tD2)(1) (ns) Packages
Low-Side Drivers, 0.5A to 1.2A Peak Output Current
MCP1401 Single, Inverting -40 to +125 0.5 18/16 18 40/40 5-pin SOT-23
MCP1402 Single, Non-inverting -40 to +125 0.5 18/16 18 40/40 5-pin SOT-23
TC1410 Single, Inverting -40 to +85 0.5 22/22 16 30/30 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
TC1410N Single, Non-inverting -40 to +85 0.5 22/22 16 30/30 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
TC1411 Single, Inverting -40 to +85 1.0 11/11 16 30/30 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
TC1411N Single, Non-inverting -40 to +85 1.0 11/11 16 30/30 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
TC1426 Dual, Inverting 0 to +70 1.2 18/18 16 75/75 8-pin PDIP, 8-pin SOIC
TC1427 Dual, Non-inverting 0 to +70 1.2 18/18 16 75/75 8-pin PDIP, 8-pin SOIC
TC1428 Dual, Inverting and Non-inverting 0 to +70 1.2 18/18 16 75/75 8-pin PDIP, 8-pin SOIC
TC4467 Quad, Inverting -40 to +85 1.2 15/15 18 40/40 14-pin PDIP, 16-pin SOIC (W)
TC4468 Quad, Non-inverting -40 to +85 1.2 15/15 18 40/40 14-pin PDIP, 16-pin SOIC (W)
TC4469 Quad, Non-inverting -40 to +85 1.2 15/15 18 40/40 14-pin PDIP, 16-pin SOIC (W)
Low-Side Drivers, 1.5A Peak Output Current
MCP1415 Single, Inverting -40 to +125 1.5 7.5/5.5 18 50/55 5-pin SOT-23
MCP1416 Single, Non-inverting -40 to +125 1.5 7.5/5.5 18 50/55 5-pin SOT-23
TC4403 Single, Non-inverting Floating Load Driver -40 to +85 1.5 5/5 18 33/38 8-pin PDIP
TC4404 Dual, Inverting -40 to +85 1.5 10/10 18 15/32 8-pin PDIP, 8-pin SOIC
TC4405 Dual, Non-inverting -40 to +85 1.5 10/10 18 15/32 8-pin PDIP, 8-pin SOIC
TC4426A Dual, Inverting -40 to +125 1.5 9/9 18 30/30 8-pin PDIP, 8-pin SOIC, 8-pin DFN
TC4427A Dual, Non-inverting -40 to +125 1.5 9/9 18 30/30 8-pin PDIP, 8-pin SOIC, 8-pin DFN
TC4428A Dual, Inverting and Non-inverting -40 to +125 1.5 9/9 18 30/30 8-pin PDIP, 8-pin SOIC, 8-pin DFN
TC4426 Dual, Inverting -40 to +125 1.5 10/10 18 20/40 8-pin PDIP, 8-pin SOIC, 8-pin DFN, 8-pin MSOP
TC4427 Dual, Non-inverting -40 to +125 1.5 10/10 18 20/40 8-pin PDIP, 8-pin SOIC, 8-pin DFN, 8-pin MSOP
TC4428 Dual, Inverting and Non-inverting -40 to +125 1.5 10/10 18 20/40 8-pin PDIP, 8-pin SOIC, 8-pin DFN, 8-pin MSOP
TC426 Dual, Inverting -40 to +85 1.5 15/10 18 50/75 8-pin PDIP, 8-pin SOIC
TC427 Dual, Non-inverting -40 to +85 1.5 15/10 18 50/75 8-pin PDIP, 8-pin SOIC
TC428 Dual, Inverting and Non-inverting -40 to +85 1.5 15/10 18 50/75 8-pin PDIP, 8-pin SOIC
TC1412 Single, Inverting -40 to +85 2 6/6 16 35/35 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
TC1412N Single, Non-inverting -40 to +85 2 6/6 16 35/35 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP14E6 Dual, Inverting -40 to +125 2 2.2/2.8 18 45/45 8-pin PDIP, 8-pin SOIC, 8-pin DFN
MCP14E7 Dual, Non-inverting -40 to +125 2 2.2/2.8 18 45/45 8-pin PDIP, 8-pin SOIC, 8-pin DFN
MCP14E8 Dual, Inverting and Non-inverting -40 to +125 2 2.2/2.8 18 45/45 8-pin PDIP, 8-pin SOIC, 8-pin DFN
MCP14E9 Dual, Inverting -40 to +125 3 2.2/2.8 18 75/75 8-pin PDIP, 8-pin SOIC, 8-pin DFN
MCP14E10 Dual, Non-inverting -40 to +125 3 2.2/2.8 18 75/75 8-pin PDIP, 8-pin SOIC, 8-pin DFN
MCP14E11 Dual, Inverting and Non-inverting -40 to +125 3 2.2/2.8 18 75/75 8-pin PDIP, 8-pin SOIC, 8-pin DFN
Note 1: tD1 = delay time from input low-to-high transition to output transition. tD2 = delay time from input high-to-low transition to output transition.
Analog and Interface Product Selector Guide 13
POWER MANAGEMENT – Power MOSFET Drivers (Continued)
Part # Confi guration Operating
Temperature
Range (°C) Peak Output
Current (A) Output Resistance
(RH/RL)
(Max. @ 25°C) Maximum Supply
Voltage (V) Input/Output Delay
(tD1, tD2)(1) (ns) Packages
Low-Side Drivers, 2.0A to 12.0A Peak Output Current
TC1413 Single, Inverting -40 to +85 3 4/4 16 35/35 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
TC1413N Single, Non-inverting -40 to +85 3 4/4 16 35/35 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
TC4423A Dual, Inverting -40 to +125 3 3 (typ)/4 (typ) 18 40 (typ)/40 (typ) 8-pin PDIP, 8-pin SOIC, 8-pin DFN
TC4424A Dual, Non-inverting -40 to +125 3 3 (typ)/4 (typ) 18 40 (typ)/40 (typ) 8-pin PDIP, 8-pin SOIC, 8-pin DFN
TC4425A Dual, Inverting and Non-inverting -40 to +125 3 3 (typ)/4 (typ) 18 40 (typ)/40 (typ) 8-pin PDIP, 8-pin SOIC, 8-pin DFN
TC4423 Dual, Inverting -40 to +125 3 5/5 18 33/38 8-pin PDIP, 16-pin SOIC (W), 8-pin DFN
TC4424 Dual, Non-inverting -40 to +125 3 5/5 18 33/38 8-pin PDIP, 16-pin SOIC (W), 8-pin DFN
TC4425 Dual, Inverting and Non-inverting -40 to +125 3 5/5 18 33/38 8-pin PDIP, 16-pin SOIC (W), 8-pin DFN
MCP14E3 Dual, Inverting -40 to +125 4.0 3.5/3.0 18 55/55 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN
MCP14E4 Dual, Non-inverting -40 to +125 4.0 3.5/3.0 18 55/55 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN
MCP14E5 Dual, Inverting and Non-inverting -40 to +125 4.0 3.5/3.0 18 55/55 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN
MCP1403 Dual, Inverting -40 to +125 4.5 3/3.5 18 48/48 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN, 16-pin SOIC
MCP1404 Dual, Non-inverting -40 to +125 4.5 3/3.5 18 48/48 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN, 16-pin SOIC
MCP1405 Dual, Inverting and Non-inverting -40 to +125 4.5 3/3.5 18 48/48 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN, 16-pin SOIC
MCP1406 Single, Inverting -40 to +125 6 1.8 (typ)/2.0 (typ) 18 30/30 5-pin TO-220, 8-pin PDIP, 8-pin 6x5 DFN, 8-pin SOIC
MCP1407 Single, Non-inverting -40 to +125 6 1.8 (typ)/2.0 (typ) 18 30/30 5-pin TO-220, 8-pin PDIP, 8-pin 6x5 DFN, 8-pin SOIC
TC429 Single, Inverting -40 to +85 6 2.5/2.5 18 53/60 8-pin PDIP, 8-pin DFN, 8-pin SOIC
TC4420 Single, Non-inverting -40 to +125 6 2.8/2.5 18 55/55 8-pin PDIP, 8-pin SOIC, 5-pin TO-220, 8-pin DFN
TC4429 Single, Inverting -40 to +125 6 2.8/2.5 18 55/55 8-pin PDIP, 8-pin SOIC, 5-pin TO-220, 8-pin DFN
TC4421 Single, Inverting -40 to +125 9 1.4 (typ)/1.7 18 30/33 8-pin PDIP, 5-pin TO-220, 8-pin DFN
TC4421A Single, Inverting -40 to +125 9 1.25 (typ)/1.5 18 38/42 8-pin PDIP, 8-pin SOIC, 5-pin TO-220, 8-pin 6x5 DFN
TC4422 Single, Non-inverting -40 to +125 9 1.4 (typ)/1.7 18 30/33 8-pin PDIP, 5-pin TO-220, 8-pin DFN
TC4422A Single, Non-inverting -40 to +125 9 1.25 (typ)/1.5 18 38/42 8-pin PDIP, 8-pin SOIC, 5-pin TO-220, 8-pin 6x5 DFN
TC4451 Single, Inverting -40 to +125 12 0.6 (typ)/1.5 18 15/15 8-pin SOIC, 8-pin PDIP, 8-pin 6x5 DFN, 5-pin TO-220, 5-pin DDPAK
TC4452 Single, Non-inverting -40 to +125 12 0.6 (typ)/1.5 18 15/15 8-pin SOIC, 8-pin PDIP, 8-pin 6x5 DFN, 5-pin TO-220, 5-pin DDPAK
High-Side/Low-Side Drivers
TC4626 Single, Inverting -40 to +85 1.5 15/10 6 35/45 8-pin PDIP, 16-pin SOIC (W)
TC4627 Single, Non-inverting -40 to +85 1.5 15/10 6 35/45 8-pin PDIP, 16-pin SOIC (W)
TC4431 Single, Inverting -40 to +85 1.5 10/10 30 62/78 8-pin PDIP, 8-pin SOIC
TC4432 Single, Non-inverting -40 to +85 1.5 10/10 30 62/78 8-pin PDIP, 8-pin SOIC
Synchronous Buck High-Side Drivers
MCP14628 Dual, Non-inverting -40 to +85 2 2.5/2.5 5 (VDD), 36 (Boot Pin) 18/20 8-pin SOIC, 8-pin 3x3 DFN
MCP14700 Dual, Non-inverting -40 to +125 2 2.5/2.5 5 (VDD), 36 (Boot Pin) 25/25 8-pin SOIC, 8-pin 3x3 DFN
Note 1: tD1 = delay time from input low-to-high transition to output transition. tD2 = delay time from input high-to-low transition to output transition.
Analog and Interface Product Selector Guide 14
POWER MANAGEMENT – Battery Chargers
Part # Mode Cell Type # of
Cells Vcc
Range (V) Cell
Voltage (V) Maximum
Charging
Current (mA)
Max. Voltage
Regulation
(%) Int/Ext
FET Features Packages
MCP73113 Linear Li-ion/Li-Polymer 1 4 to 16 4.1, 4.2, 4.35, 4.4 1100 ±0.5 Int 6.5V Overvoltage Protection 10-pin 3x3 DFN
MCP73114 Linear Li-ion/Li-Polymer 1 4 to 16 4.1, 4.2, 4.35, 4.4 1100 ±0.5 Int 5.8V Overvoltage Protection 10-pin 3x3 DFN
MCP73123 Linear LiFePO4 1 4 to 16 3.6 1100 ±0.5 Int 6.5V Overvoltage Protection, LiFePO4 charging 10-pin 3x3 DFN
MCP73213 Linear Li-ion/Li-Polymer 2 4 to 16 8.2, 8.4, 8.7, 8.8 1100 ±0.6 Int 13V Overvoltage Protection 10-pin 3x3 DFN
MCP73223 Linear LiFePO4 2 4 to 16 7.2 1100 ±0.6 Int 13V Overvoltage Protection, LiFePO4 charging 10-pin 3x3 DFN
MCP73826 Linear Li-Ion/Li-Polymer 1 4.5 to 5.5 4.1, 4.2 N/A ±1.0 Ext Small size, charge current set by external FET 6-pin SOT-23
MCP73827 Linear Li-Ion/Li-Polymer 1 4.5 to 5.5 4.1, 4.2 N/A ±1.0 Ext Mode indicator, Charge current monitor, Charge current set by external
FET 8-pin MSOP
MCP73828 Linear Li-Ion/Li Polymer 1 4.5 to 5.5 4.1, 4.2 N/A ±1.0 Ext Temperature monitor, Charge current set by external FET 8-pin MSOP
MCP73841 Linear Li-Ion/Li-Polymer 1 4.5 to 12 4.1, 4.2 N/A ±0.5 Ext Safety charge timers, Temperature monitor, Charge current set by
external FET 10-pin MSOP
MCP73842 Linear Li-Ion/Li-Polymer 2 8.7 to 12 8.2, 8.4 N/A ±0.5 Ext Safety charge timers, Temperature monitor, Charge current set by
external FET 10-pin MSOP
MCP73843 Linear Li-Ion/Li-Polymer 1 4.5 to 12 4.1, 4.2 N/A ±0.5 Ext Safety charge timers, Charge current set by external FET 8-pin MSOP
MCP73844 Linear Li-Ion/Li-Polymer 2 8.7 to 12 8.2, 8.4 N/A ±0.5 Ext Safety charge timers, Charge current set by external FET 8-pin MSOP
MCP73811 Linear Li-Ion/Li-Polymer 1 3.7 to 6.0 4.2 500 ±1.0 Int Selectable charge current (100 mA, 500 mA), Charge enable input 5-pin SOT-23
MCP73812 Linear Li-Ion/Li Polymer 1 3.7 to 6.0 4.2 500 ±1.0 Int Programmable charge current (100 mA, 500 mA), Charge enable input 5-pin SOT-23
MCP73831 Linear Li-Ion/Li-Polymer 1 3.7 to 6.0 4.2, 4.35, 4.4, 4.5 500 ±0.75 Int UVLO, Thermal regulation, Programmable charge current,
Tri-state STAT pin 5-pin SOT-23, 8-pin
2x3 DFN
MCP73832 Linear Li-Ion/Li-Polymer 1 3.7 to 6.0 4.2, 4.35, 4.4, 4.5 500 ±0.75 Int UVLO, Thermal regulation, Programmable charge current,
Open-drain STAT pin 5-pin SOT-23, 8-pin
2x3 DFN
MCP73853 Linear Li-Ion/Li-Polymer 1 4.5 to 5.5 4.1, 4.2 500 ±0.5 Int USB control, Safety charge timers, Temperature monitor,
Thermal regulation 16-pin 4x4 QFN
MCP73855 Linear Li-Ion/Li-Polymer 1 4.5 to 5.5 4.1, 4.2 500 ±0.5 Int USB control, Safety charge timers, Thermal regulation 10-pin 3x3 DFN
MCP73833 Linear Li-Ion/Li-Polymer 1 3.7 to 6.0 4.2, 4.35, 4.4, 4.5 1000 ±0.75 Int UVLO, Thermal regulation, Thermistor input, LDO Test mode,
Multiple VREG outputs, Safety timer, Power good output 10-pin 3x3 DFN,
10-pin MSOP
MCP73834 Linear Li-Ion/Li-Polymer 1 3.7 to 6.0 4.2, 4.35, 4.4, 4.5 1000 ±0.75 Int UVLO, Thermal regulation, Thermistor input, LDO Test mode,
Multiple VREG outputs, Safety timer, Timer enable input 10-pin 3x3 DFN,
10-pin MSOP
MCP73837 Linear Li-Ion/Li-Polymer 1 3.7 to 6.0 4.2, 4.35, 4.4, 4.5 1000 ±0.75 Int Dual input (USB, DC input from adapter) auto-switching, UVLO,
Thermal regulation, Thermistor input, Power good output 10-pin 3x3 DFN,
10-pin MSOP
MCP73838 Linear Li-Ion/Li Polymer 1 3.7 to 6.0 4.2, 4.35, 4.4, 4.5 1000 ±0.75 Int Dual input (USB, DC input from adapter) auto-switching, UVLO,
Thermal regulation, Timer enable input 10-pin 3x3 DFN,
10-pin MSOP
MCP73861 Linear Li-Ion/Li-Polymer 1 4.5 to 12 4.1, 4.2 1000 ±0.5 Int Safety charge timers, Temperature monitor, Thermal regulation,
Flashing STAT1 output on charge complete 16-pin 4x4 QFN,
16-pin SOIC
MCP73862 Linear Li-Ion/Li-Polymer 2 8.7 to 12 8.2, 8.4 1000 ±0.5 Int Safety charge timers, Temperature monitor, Thermal regulation,
hi-Z STAT1 output on charge complete 16-pin 4x4 QFN,
16-pin SOIC
MCP73863 Linear Li-Ion/Li-Polymer 1 4.5 to 12 4.1, 4.2 1000 ±0.5 Int Safety charge timers, Temperature monitor, Thermal regulation,
hi-Z STAT1 output on charge complete 16-pin 4x4 QFN,
16-pin SOIC
MCP73864 Linear Li-Ion/Li-Polymer 2 8.7 to 12 8.2, 8.4 1000 ±0.5 Int Safety charge timers, Temperature monitor, Thermal regulation,
hi-Z STAT1 output on charge complete 16-pin 4x4 QFN,
16-pin SOIC
MCP73871 Linear Li-Ion/Li-Polymer 1 3.75 to 6.0 4.2, 4.35, 4.4 1500 (A/C Adapter)
500 (USB) ±0.5 Int Simultaneous charging of load and battery, Load-dependent charging,
Multiple programmable charge currents 20-pin 4x4 QFN,
20-pin SSOP
POWER MANAGEMENT – Hot Swap Controllers
Part # Number of
Outputs VPOS to VNEG
Differential Voltage
(V) Junction Temperature
Range (°C) OVLO UVLO Power good Int/Ext FET Applications Packages
MCP18480 1 -0.3 to +15.0 -40 to +85 Adjustable Adjustable Adjustable Ext -48V Telecom/Datacom, Bus/Backplane 20-pin SSOP
Analog and Interface Product Selector Guide 15
LINEAR
LINEAR – Op Amps
Part # # per
Package GBWP IQ Typical
(μA) VOS Max
(mV) Typical Input
Bias Current
(pA)
Input Voltage
Noise Density
(nV/rtHz) Operating
Voltage (V) Temperature
Range (°C) Features Packages
MCP6441 1 9 kHz 0.45 4.5 1 190(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 5-pin SOT-23(S), 5-pin SC-70(S)
MCP6442 2 9 kHz 0.45 4.5 1 190(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 TDFN
MCP6444 4 9 kHz 0.45 4.5 1 190(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP
MCP6031 1 10 kHz 0.9 0.15 1 165(1) 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN, 5-pin SOT-23
MCP6032 2 10 kHz 0.9 0.15 1 165(1) 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP
MCP6033 1 10 kHz 0.9 0.15 1 165(1) 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN
MCP6034 4 10 kHz 0.9 0.15 1 165(1) 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP
MCP6041 1 14 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 5-pin SOT-23(S)
MCP6042 2 14 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6043 1 14 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 6-pin SOT-23(S)
MCP6044 4 14 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP6141 1 100 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, G>10 stable 5-pin SOT-23(S), 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6142 2 100 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, G>10 stable 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6143 1 100 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, G>10 stable,
Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 6-pin SOT-23(S),
MCP6144 4 100 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, G>10 stable 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP606 1 155 kHz 19 0.25 1 38(1) 2.5 to 6.0 -40 to +125 Rail-to-Rail Output 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP, 5-pin SOT23(S)
MCP607 2 155 kHz 19 0.25 1 38(1) 2.5 to 6.0 -40 to +85 Rail-to-Rail Output 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP
MCP608 1 155 kHz 19 0.25 1 38(1) 2.5 to 6.0 -40 to +85 Rail-to-Rail Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP
MCP609 4 155 kHz 19 0.25 1 38(1) 2.5 to 6.0 -40 to +85 Rail-to-Rail Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP616 1 190 kHz 19 0.15 15000 32(1) 2.3 to 5.5 -40 to +85 Rail-to-Rail Output, PNP input 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP617 2 190 kHz 19 0.15 15000 32(1) 2.3 to 5.5 -40 to +85 Rail-to-Rail Output, PNP input 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP618 1 190 kHz 19 0.15 15000 32(1) 2.3 to 5.5 -40 to +85 Rail-to-Rail Output, Chip select, PNP input 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP619 4 190 kHz 19 0.15 15000 32(1) 2.3 to 5.5 -40 to +85 Rail-to-Rail Output, PNP input 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP6231 1 300 kHz 20 5 1 52(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 TDFN,
5-pin SC-70(U), 5-pin SOT-23(S,R,U)
MCP6232 2 300 kHz 20 5 1 52(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 TDFN
MCP6234 4 300 kHz 20 5 1 52(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP6051 1 385 kHz 30 0.15 1 34(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 DFN, 5-pin SOT-23(S)
MCP6052 2 385 kHz 30 0.15 1 34(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 DFN
MCP6054 4 385 kHz 30 0.15 1 34(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP
MCP6241 1 550 kHz 50 5 1 45
(1)
1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 2x3
TDFN, 5-pin SC-70
(U)
, 5-pin SOT-23
(S,R,U)
,
MCP6242 2 550 kHz 50 5 1 45
(1)
1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6244 4 550 kHz 50 5 1 45(1) 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP6061 1 730 kHz 60 0.15 1 25(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 DFN, 5-pin SOT-23(S)
MCP6062 2 730 kHz 60 0.15 1 25(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 DFN
MCP6064 4 730 kHz 60 0.15 1 25(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP
MCP6001 1 1 MHz 100 4.5 1 28(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(R)
MCP6002 2 1 MHz 100 4.5 1 28(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN
Legend: S = Standard Pinout; R = Reverse Pinout; U = Alternative Pinout
Note 1: Values are typical at 1 kHz
2: Values are typical at 10 kHz
Analog and Interface Product Selector Guide 16
LINEAR – Op Amps (Continued)
Part # # per
Package GBWP IQ Typical
(μA) Vos Max
(mV) Typical Input
Bias Current
(pA)
Input Voltage
Noise Density
(nV/rtHz) Operating
Voltage (V) Temperature
Range (°C) Features Packages
MCP6004 4 1 MHz 100 4.5 1 28(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP6401 1 1 MHz 45 4.5 1 28(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(R)
MCP6402 2 1 MHz 45 4.5 1 28(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 TDFN
MCP6404 4 1 MHz 45 4.5 1 28(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP
MCP6L01 1 1 MHz 85 5 2 24(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(S)
MCP6L02 2 1 MHz 85 5 2 24(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP
MCP6L04 4 1 MHz 85 5 2 24(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP
MCP6071 1 1.2 MHz 110 0.15 1 19(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 DFN, 5-pin SOT-23(S)
MCP6072 2 1.2 MHz 110 0.15 1 19(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 DFN
MCP6074 4 1.2 MHz 110 0.15 1 19(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP
MCP6H01 1 1.2 MHz 135 3.5 10 35(1) Single Supply: 3.5 to 16
Dual Supply: ±1.75 to ±8 -40 to +125 Rail-to-Rail Output 8-pin SOIC, 8-pin 2x3 TDFN
MCP6H02 2 1.2 MHz 135 3.5 10 35(1) Single Supply: 3.5 to 16
Dual Supply: ±1.75 to ±8 -40 to +125 Rail-to-Rail Output 8-pin SOIC, 8-pin 2x3 TDFN
MCP6H04 4 1.2 MHz 135 3.5 10 35(1) Single Supply: 3.5 to 16
Dual Supply: ±1.75 to ±8 -40 to +125 Rail-to-Rail Output 14-pin SOIC, 14-pin TSSOP
MCP6271 1 2 MHz 170 3 1 20(1) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP,
5-pin SOT-23(S,R),
MCP6272 2 2 MHz 170 3 1 20(1) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6273 1 2 MHz 170 3 1 20(1) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 6-pin SOT-23(S)
MCP6274 4 2 MHz 170 3 1 20(1) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP6275 2 2 MHz 150 3 1 20(1) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output,
Dual connected, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6L71 1 2 MHz 150 4 1 19(2) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC(S), 8-pin MSOP(S), 5-pin SOT-23(S,R)
MCP6L72 2 2 MHz 150 4 1 19(2) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP
MCP6L74 4 2 MHz 150 4 1 19(2) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP
MCP601 1 2.8 MHz 230 2 1 29(1) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP,
5-pin SOT-23(S,R)
MCP602 2 2.8 MHz 230 2 1 29(1) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP
MCP603 1 2.8 MHz 230 2 1 29(1) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP, 6-pin SOT-23(S)
MCP604 4 2.8 MHz 230 2 1 29(1) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP6L1 1 2.8 MHz 200 3 1 21(2) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output 8-pin SOIC(S), 8-pin MSOP(S), 5-pin SOT-23(S,R)
MCP6L2 2 2.8 MHz 200 3 1 21(2) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output 8-pin SOIC, 8-pin MSOP
MCP6L4 4 2.8 MHz 200 3 1 21(2) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output 14-pin SOIC, 14-pin TSSOP
MCP6281 1 5 MHz 445 3 1 16(1) 2.2 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 5-pin SOT-23(S,R)
MCP6282 2 5 MHz 445 3 1 16(1) 2.2 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6283 1 5 MHz 445 3 1 16(1) 2.2 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 6-pin SOT-23(S,R)
MCP6284 4 5 MHz 445 3 1 16(1) 2.2 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP6285 2 5 MHz 400 3 1 16(1) 2.2 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Dual connected,
Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6286 1 3.5 MHz 540 1.5 1 5.4(2) 2.2 to 5.5 -40 to +125 Rail-to-Rail Output, Low noise 5-pin SOT-23(S,R)
MCP6021 1 10 MHz 1000 0.5 1 8.7(2) 2.5 to 5.5 -40 to +125 Rail-to-Rail Input/Output, 1/2 VCC VREF 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP, 8-pin MSOP,
5-pin SOT-23(S,R)
Legend: S = Standard Pinout; R = Reverse Pinout; U = Alternative Pinout
Note 1: Values are typical at 1 kHz
2: Values are typical at 10 kHz
Analog and Interface Product Selector Guide 17
LINEAR – Op Amps (Continued)
Part # # per
Package GBWP IQ Typical
(μA) Vos Max
(mV) Typical Input
Bias Current
(pA)
Input Voltage
Noise Density
(nV/rtHz) Operating
Voltage (V) Temperature
Range (°C) Features Packages
MCP6022 2 10 MHz 1000 0.5 1 8.7(2) 2.5 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP
MCP6023 1 10 MHz 1000 0.5 1 8.7(2) 2.5 to 5.5 -40 to +125 Rail-to-Rail Input/Output, Chip select,
1/2 VCC VREF 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP
MCP6024 4 10 MHz 1000 0.5 1 8.7(2) 2.5 to 5.5 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP6291 1 10 MHz 1000 3 1 8.7(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 5-pin SOT-23(S,R)
MCP6292 2 10 MHz 1000 3 1 8.7(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6293 1 10 MHz 1000 3 1 8.7(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 6-pin SOT-23(S)
MCP6294 4 10 MHz 1000 3 1 8.7(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP6295 2 10 MHz 1100 3 1 8.7(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Dual connected,
Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6L91 1 10 MHz 850 4 1 9.4(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC(S), 8-pin MSOP(S), 5-pin SOT-23(S,R)
MCP6L92 2 10 MHz 850 4 1 9.4(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP
MCP6L94 4 10 MHz 850 4 1 9.4(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP
MCP621 1 20 MHz 2500 0.2 5 13(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip select,
mCal Technology 8-pin SOIC
MCP621S 1 20 MHz 2500 0.2 5 13(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, mCal Technology 5-pin SOT-23(S)
MCP622 2 20 MHz 2500 0.2 5 13(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, mCal Technology 8-pin SOIC, 8-pin 3x3 DFN
MCP623 1 20 MHz 2500 0.2 5 13(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip select,
mCal Technology 6-pin SOT-23(S)
MCP624 4 20 MHz 2500 0.2 5 13(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, mCal Technology 14-pin SOIC, 14-pin TSSOP
MCP625 2 20 MHz 2500 0.2 5 13(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip selects,
mCal Technology 10-pin MSOP, 10-pin 3x3 DFN
MCP629 4 20 MHz 2500 0.2 5 13(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output,Chip selects,
mCal Technology 16-pin 4x4 QFN
MCP631 1 24 MHz 2500 8 4 10(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output 8-pin SOIC
MCP632 2 24 MHz 2500 8 4 10(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output 8-pin SOIC, 8-pin 3x3 DFN
MCP633 1 24 MHz 2500 8 4 10(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip select 8-pin SOIC
MCP635 2 24 MHz 2500 8 4 10(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip selects 10-pin MSOP, 10-pin 3x3 DFN
MCP651 1 50 MHz 6000 0.2 6 7.5(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip select,
mCal Technology 8-pin SOIC
MCP651S 1 50 MHz 6000 0.2 6 7.5(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, mCal Technology 5-pin SOT-23(S)
MCP652 2 50 MHz 6000 0.2 6 7.5(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, mCal Technology 8-pin SOIC, 8-pin 3x3 DFN
MCP653 1 50 MHz 6000 0.2 6 7.5(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip select,
mCal Technology 6-pin SOT-23(S)
MCP654 4 50 MHz 6000 0.2 6 7.5(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, mCal Technology 14-pin SOIC, 14-pin TSSOP
MCP655 2 50 MHz 6000 0.2 6 7.5(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip selects,
mCal Technology 10-pin MSOP, 10-pin 3x3 DFN
MCP659 4 50 MHz 6000 0.2 6 7.5
(3)
2.5 to 5.5 -40 to +125 Rail-to-Rail Output,Chip selects,
mCal Technology 16-pin 4x4 QFN
MCP661 1 60 MHz 6000 8 6 6.8
(3)
2.5 to 5.5 -40 to +125 Rail-to-Rail Output 8-pin SOIC
MCP662 2 60 MHz 6000 8 6 6.8
(3)
2.5 to 5.5 -40 to +125 Rail-to-Rail Output 8-pin SOIC, 8-pin 3x3 DFN
MCP663 1 60 MHz 6000 8 6 6.8
(3)
2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip select 8-pin SOIC
MCP665 2 60 MHz 6000 8 6 6.8
(3)
2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip selects 10-pin MSOP, 10-pin 3x3 DFN
Legend: S = Standard Pinout; R = Reverse Pinout; U = Alternative Pinout
Note 1: Values are typical at 1 kHz
2: Values are typical at 10 kHz
3: Values are typical at 1 MHz
Analog and Interface Product Selector Guide 18
LINEAR – High Precision Operational Amplifi ers
Part # # per
Package GBWP IQ Max
(mA) Vos Max
(μV) Vos Drift Max
(μV/°C) Operating
Voltage (V) Temperature
Range (°C) Features Packages
Chopper Stabilized
TC7650 1 2.0 MHz 3.5 5 0.05 4.5 to 16 0 to +70 Single and Split Supply 8-pin PDIP, 14-pin PDIP
TC7652 1 0.4 MHz 3 5 0.05 5 to 16 0 to +70 Single and Split Supply, Low Noise 8-pin PDIP, 14-pin PDIP
Auto-Zero
MCP6V01 1 1.3 MHz 0.4 2 0.05 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 TDFN
MCP6V02 2 1.3 MHz 0.4 2 0.05 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 4x4 DFN
MCP6V03 1 1.3 MHz 0.4 2 0.05 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin SOIC, 8-pin 2x3 TDFN
MCP6V06 1 1.3 MHz 0.4 3 0.05 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 TDFN
MCP6V07 2 1.3 MHz 0.4 3 0.05 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 4x4 DFN
MCP6V08 1 1.3 MHz 0.4 3 0.05 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin SOIC, 8-pin 2x3 TDFN
MCP6V26 1 2 MHz 0.8 2 0.05 2.3 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 TDFN
MCP6V27 2 2 MHz 0.8 2 0.05 2.3 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP, 8-pin 4x4 DFN
MCP6V28 1 2 MHz 0.8 2 0.05 2.3 to 5.5 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 TDFN
TC913A/B 2 1.5 MHz 1.1 15 0.15/0.30 7 to 16 0 to +70 Single and Split Supply 8-pin PDIP, 8-pin SOIC
LINEAR – Programmable Gain Amplifi ers (PGA)
Part # Channels -3dB BW
(MHz) IQ Typ.
(mA) Vos (μV) Operating
Voltage (V) Temperature
Range (°C) Features Packages
MCP6S21 1 2 to 12 1.1 275 2.5 to 5.5 -40 to +85 SPI, 8 Gain steps, Software shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6S22 2 2 to 12 1.1 275 2.5 to 5.5 -40 to +85 SPI, 8 Gain steps, Software shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6S26 6 2 to 12 1.1 275 2.5 to 5.5 -40 to +85 SPI, 8 Gain steps, Software shutdown 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP6S28 8 2 to 12 1.1 275 2.5 to 5.5 -40 to +85 SPI, 8 Gain steps, Software shutdown 16-pin PDIP, 16-pin SOIC
MCP6S91 1 1 to 18 1.0 4000 2.5 to 5.5 -40 to +125 SPI, 8 Gain steps, Software shutdown, VREF 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6S92 2 1 to 18 1.0 4000 2.5 to 5.5 -40 to +125 SPI, 8 Gain steps, Software shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6S93 2 1 to 18 1.0 4000 2.5 to 5.5 -40 to +125 SPI, 8 Gain steps, Software shutdown, VREF, SO 10-pin MSOP
LINEAR – Selectable Gain Amplifi ers (SGA)
Part # Channels -3dB BW
(kHz) IQ (μA) VOS (mV) Operating
Voltage (V) Temperature
Range (°C) Gain Steps
(V/V) Features Packages
MCP6G01 1 900 110 4.5 1.8 to 5.5 -40 to +125 1, 10, 50 Tri-State control pin 8-pin SOIC, 8-pin MSOP, 5-pin SOT-23
(S,R,U)
MCP6G02 2 900 110 4.5 1.8 to 5.5 -40 to +125 1, 10, 50 Tri-State control pin 8-pin SOIC, 8-pin MSOP
MCP6G03 1 900 110 4.5 1.8 to 5.5 -40 to +125 1, 10, 50 Tri-State control pin,
Chip select 8-pin SOIC, 8-pin MSOP
MCP6G04 4 900 110 4.5 1.8 to 5.5 -40 to +125 1, 10, 50 Tri-State control pin 14-pin SOIC, 14-pin TSSOP
Analog and Interface Product Selector Guide 19
MIXED SIGNAL
MIXED SIGNAL – Successive Approximation Register (SAR) A/D Converters
Part # Resolution
(bits) Maximum
Sampling Rate
(ksamples/sec) # of Input
Channels Input Type Interface Input Voltage
Range (V) Max. Supply
Current (μA) Max. INL Temperature
Range (°C) Packages
MCP3021 10 22 1 Single-ended I2C™ 2.7 to 5.5 250 ±1 LSB -40 to +125 5-pin SOT-23A
MCP3001 10 200 1 Single-ended SPI 2.7 to 5.5 500 ±1 LSB -40 to +85 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin TSSOP
MCP3002 10 200 2 Single-ended SPI 2.7 to 5.5 650 ±1 LSB -40 to +85 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin TSSOP
MCP3004 10 200 4 Single-ended SPI 2.7 to 5.5 550 ±1 LSB -40 to +85 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP3008 10 200 8 Single-ended SPI 2.7 to 5.5 550 ±1 LSB -40 to +85 16-pin PDIP, 16-pin SOIC
MCP3221 12 22 1 Single-ended I2C™ 2.7 to 5.5 250 ±2 LSB -40 to +125 5-pin SOT-23A
MCP3201 12 100 1 Single-ended SPI 2.7 to 5.5 400 ±1 LSB -40 to +85 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin TSSOP
MCP3202 12 100 2 Single-ended SPI 2.7 to 5.5 550 ±1 LSB -40 to +85 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin TSSOP
MCP3204 12 100 4 Single-ended SPI 2.7 to 5.5 400 ±1 LSB -40 to +85 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP3208 12 100 8 Single-ended SPI 2.7 to 5.5 400 ±1 LSB -40 to +85 16-pin PDIP, 16-pin SOIC
MCP3301 13 100 1 Differential SPI 2.7 to 5.5 450 ±1 LSB -40 to +85 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin TSSOP
MCP3302 13 100 2 Differential SPI 2.7 to 5.5 450 ±1 LSB -40 to +85 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP3304 13 100 4 Differential SPI 2.7 to 5.5 450 ±1 LSB -40 to +85 16-pin PDIP, 16-pin SOIC
LINEAR – Comparators
Part # # per
Package VREF
(V) Typical Propagation
Delay (μs) IQ Typical
(μA) Vos Max
(mV) Operating
Voltage (V) Temperature
Range (°C) Features Packages
MCP6541 1 – 4 1 5 1.6 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(S,U),
8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6542 2 – 4 1 5 1.6 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6543 1 – 4 1 5 1.6 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6544 4 – 4 1 5 1.6 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP6546 1 – 4 1 5 1.6 to 5.5 -40 to +125 Open-drain, 9V, Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(S,U),
8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6547 2 – 4 1 5 1.6 to 5.5 -40 to +125 Open-drain, 9V, Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6548 1 – 4 1 5 1.6 to 5.5 -40 to +125 Open-drain, 9V, Rail-to-Rail Input/Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP6549 4 – 4 1 5 1.6 to 5.5 -40 to +125 Open-drain, 9V, Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP65R41 1 1.21/2.4 4 2.5 10 1.8 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output, VREF 6-pin SOT-23
MCP65R46 1 1.21/2.4 4 2.5 10 1.8 to 5.5 -40 to +125 Open Drain, Rail-to-Rail Input/Output, VREF 6-pin SOT-23
MCP6561 1 – 0.047 100 10 1.8 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(S)
MCP6562 2 – 0.047 100 10 1.8 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP
MCP6564 4 – 0.047 100 10 1.8 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP
MCP6566 1 – 0.047 100 10 1.8 to 5.5 -40 to +125 Open-Drain, Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(S)
MCP6567 2 – 0.047 100 10 1.8 to 5.5 -40 to +125 Open-Drain, Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP
MCP6569 4 – 0.047 100 10 1.8 to 5.5 -40 to +125 Open-Drain, Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP
Legend: S = Standard Pinout; R = Reverse Pinout; U = Alternative Pinout
Analog and Interface Product Selector Guide 20
MIXED SIGNAL – Dual Slope A/D Converters
Part # Supply
Voltage (V) Input Voltage Range Resolution Sampling
Rate (Conv/s) Input
Channels Data
Interface Temperature
Range (°C) Features Packages
TC500 ±4.5 to ±7.5 VSS + 1.5V to VDD – 1.5V Up to 16 bits 4 to 10 1 3-Wire 0 to +70 Differential input range, Programmable resolution/
conversion time 16-pin PDIP, 16-pin SOIC, 16-pin CerDIP
TC500A ±4.5 to ±7.5 VSS + 1.5V to VDD – 1.5V Up to 17 bits 4 to 10 1 3-Wire 0 to +70 Differential input range, Programmable resolution/
conversion time 16-pin PDIP, 16-pin SOIC, 16-pin CerDIP
TC510 +4.5 to +5.5 VSS + 1.5V to VDD – 1.5V Up to 17 bits 4 to 10 1 3-Wire 0 to +70 Differential input range, Programmable resolution/
conversion time, Charge pump (-V) output pin 24-pin PDIP, 24-pin SOIC
TC514 +4.5 to +5.5 VSS + 1.5V to VDD – 1.5V Up to 17 bits 4 to 10 4 3-Wire 0 to +70 Differential input range, Programmable resolution/
conversion time, Charge pump (-V) output pin 28-pin PDIP, 28-pin SOIC
TC520A +4.5 to +5.5 – – – – Serial port 0 to +70 Optional serial interface adapter for
TC500/500A/510/514 14-pin PDIP, 16-pin SOIC
TC7109 ±4.5 to ±5.5 VSS + 1.5V to VDD – 1.0V 12 bits plus
sign bit 2 to 10 1 Parallel or
Serial port -25 to +85 Differential input range 40-pin PDIP, 44-pin PLCC, 44-pin MQFP
TC7109A ±4.5 to ±5.5 VSS + 1.5V to VDD – 1.0V 12 bits plus
sign bit 2 to 10 1 Parallel or
Serial port -25 to +85 Differential input range 40-pin PDIP, 44-pin PLCC, 44-pin MQFP
MIXED SIGNAL – Energy Measurement ICs
Part # Dynamic
Range Typical
Accuracy ADC
Channels Gain
Selection Output Type Typical Voltage
Reference Drift
(ppm/°C)
Typical
Supply
Current (mA)
Analog
Voltage
Range (V)
Digital
Voltage
Range (V) Temperature
Range (°C) Features Packages
MCP3901 24-bit resolution 91 dB SINAD 2 up to 32 SPI 12 2.6 4.5 to 5.5 2.7 to 5.5 -40 to +125 Phase correction,
Programmable data rate 20-pin SSOP,
20-pin 4x4 QFN
MCP3903 24-bit resolution 91 dB SINAD 6 up to 32 SPI 5 8.3 4.5 to 5.5 2.7 to 3.6 -40 to +125 Phase correction,
Programmable data rate 28-pin SSOP
MCP3905A 500:1 0.1% 2 up to 16 Active power pulse 15 3.9 4.5 to 5.5 4.5 to 5.5 -40 to +125 Active power calculation 24-pin SSOP
MCP3905L 500:1 0.1% 2 up to 16 Active power pulse 15 3.9 4.5 to 5.5 4.5 to 5.5 -40 to +125 Active power calculation,
Reduced pulse-width 24-pin SSOP
MCP3906A 1000:1 0.1% 2 up to 32 Active power pulse 15 3.9 4.5 to 5.5 4.5 to 5.5 -40 to +125 Active power calculation 24-pin SSOP
MCP3909 1000:1 0.1% 2 up to 16 Active power pulse/
SPI 15 3.9 4.5 to 5.5 4.5 to 5.5 -40 to +125 Active power calculation 24-pin SSOP
MIXED SIGNAL – Delta-Sigma A/D Converters
Part # Resolution
(bits) Maximum
Sampling Rate
(samples/sec) # of Input
Channels Interface Supply Voltage
Range (V) Typical
Supply
Current (μA) Typical INL
(ppm) Temperature
Range (°C) Features Packages
MCP3421 18 to 12 4 to 240 1 Diff I2C™ 2.7 to 5.5 155 10 -40 to +125 PGA, VREF 6-pin SOT-23A
MCP3422 18 to 12 4 to 240 2 Diff I2C™ 2.7 to 5.5 145 10 -40 to +125 PGA, VREF 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN
MCP3423 18 to 12 4 to 240 2 Diff I2C™ 2.7 to 5.5 145 10 -40 to +125 PGA, VREF, Selectable I2C™ addressing 10-pin MSOP, 10-pin 3x3 DFN
MCP3424 18 to 12 4 to 240 4 Diff I2C™ 2.7 to 5.5 145 10 -40 to +125 PGA, VREF, Selectable I2C™ addressing 14-pin SOIC, 14-pin TSSOP
MCP3425 16 to 12 15 to 240 1 Diff I2C™ 2.7 to 5.5 155 10 -40 to +125 PGA, VREF 6-pin SOT-23A
MCP3426 16 to 12 15 to 240 2 Diff I2C™ 2.7 to 5.5 145 10 -40 to +125 PGA, VREF 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN
MCP3427 16 to 12 15 to 240 2 Diff I2C™ 2.7 to 5.5 145 10 -40 to +125 PGA, VREF, Selectable I2C™ addressing 10-pin MSOP, 10-pin 3x3 DFN
MCP3428 16 to 12 15 to 240 4 Diff I2C™ 2.7 to 5.5 145 10 -40 to +125 PGA, VREF, Selectable I2C™ addressing 14-pin SOIC, 14-pin TSSOP
MCP3550-50 22 13 1 Diff SPI 2.7 to 5.5 120 2 -40 to +125 50 Hz rejection 8-pin SOIC, 8-pin MSOP
MCP3550-60 22 15 1 Diff SPI 2.7 to 5.5 140 2 -40 to +125 60 Hz rejection 8-pin SOIC, 8-pin MSOP
MCP3551 22 14 1 Diff SPI 2.7 to 5.5 120 2 -40 to +125 Simultaneous 50/60 Hz rejection 8-pin SOIC, 8-pin MSOP
MCP3553 20 60 1 Diff SPI 2.7 to 5.5 140 2 -40 to +125 8-pin SOIC, 8-pin MSOP
Analog and Interface Product Selector Guide 21
MIXED SIGNAL – Display A/D Converters
Part # Display
Type Supply
Voltage (V) Resolution
(Digits) Resolution
(Counts) Power
(mW) Temperature Range
(°C) Features Packages
TC7106 LCD 9 3½ ±2,000 10 -25 to +85 For DMM, DPM, Data logger applications 40-pin PDIP, 44-pin PLCC, 44-pin MQFP
TC7106A LCD 9 3½ ±2,000 10 -25 to +85 For DMM, DPM, Data logger applications 40-pin PDIP, 44-pin PLCC, 44-pin MQFP
TC7107 LED ±5 3½ ±2,000 10 -25 to +85 For DMM, DPM, Data logger applications 40-pin PDIP, 44-pin PLCC, 44-pin MQFP
TC7107A LED ±5 3½ ±2,000 10 -25 to +85 For DMM, DPM, Data logger applications 40-pin PDIP, 44-pin PLCC, 44-pin MQFP
TC7116 LCD 9 3½ ±2,000 10 -25 to +85 Hold function 40-pin PDIP, 44-pin PLCC, 44-pin MQFP
TC7116A LCD 9 3½ ±2,000 10 -25 to +85 Hold function 40-pin PDIP, 44-pin PLCC, 44-pin MQFP
TC7117 LED ±5 3½ ±2,000 10 -25 to +85 Hold function 40-pin PDIP, 44-pin PLCC, 44-pin MQFP
TC7117A LED ±5 3½ ±2,000 10 -25 to +85 Hold function 40-pin PDIP, 44-pin PLCC, 44-pin MQFP
TC7126 LCD 9 3½ ±2,000 0.5 -25 to +85 Low-power TC7106 40-pin PDIP, 44-pin PLCC, 44-pin MQFP
TC7126A LCD 9 3½ ±2,000 0.5 -25 to +85 Low-power TC7106 40-pin PDIP, 44-pin PLCC, 44-pin MQFP
TC7129 LCD 9 4½ ±20,000 4.5 0 to +70 Lowest noise ±3 mV sensitivity 40-pin PDIP, 44-pin PLCC, 44-pin MQFP
MIXED SIGNAL – Digital Potentiometers
Part # Number
of Taps Memory Number per
Package Interface Resistance
(kOhms) INL
(max) DNL
(max) Temperature
Range (°C) Comments Packages
MCP4011 64 Volatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Potentiometer mode 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN
MCP4012 64 Volatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Rheostat mode 6-pin SOT-23
MCP4013 64 Volatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Potentiometer to VSS 6-pin SOT-23
MCP4014 64 Volatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Rheostat to VSS 5-pin SOT-23
MCP4017 128 Volatile 1 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 7-bit, Volatile, I2C digital potentiometer 6-pin SC-70
MCP4018 128 Volatile 1 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 7-bit, Volatile, I2C digital potentiometer 6-pin SC-70
MCP4019 128 Volatile 1 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 7-bit, Volatile, I2C digital potentiometer 5-pin SC-70
MCP40D17 128 Volatile 1 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 7-bit, Volatile, I2C digital potentiometer 6-pin SC-70
MCP40D18 128 Volatile 1 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 7-bit, Volatile, I2C digital potentiometer 6-pin SC-70
MCP40D19 128 Volatile 1 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 7-bit, Volatile, I2C digital potentiometer 5-pin SC-70
MCP4021 64 Nonvolatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Potentiometer mode, Shutdown, WiperLock™ Technology 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN
MCP4022 64 Nonvolatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Rheostat mode, Shutdown, WiperLock™ Technology 6-pin SOT-23
MCP4023 64 Nonvolatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Potentiometer to VSS, WiperLock™ Technology 6-pin SOT-23
MCP4024 64 Nonvolatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Rheostat to VSS, Shutdown, WiperLock™ Technology 5-pin SOT-23
MCP4141 128 Nonvolatile 1 SPI 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN
MCP4142 128 Nonvolatile 1 SPI 5, 10, 50, 100 0.8 0.25 -40 to +125 Rheostat mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN
MCP4241 128 Nonvolatile 2 SPI 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, Shutdown, WiperLock™ Technology 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP, 16-pin 4x4 QFN
MCP4242 128 Nonvolatile 2 SPI 5, 10, 50, 100 0.8 0.25 -40 to +125 Rheostat mode, Shutdown 10-pin MSOP, 10-pin 3x3 DFN
MIXED SIGNAL – Binary and BCD A/D Converters
Part # Description Supply
Voltage (V) Input Voltage Range Resolution
(Digits) Resolution
(Counts) Max Power
(mW) Data
Interface Temperature
Range (°C) Features Packages
TC850 Binary A/D ±5 VSS + 1.5V to VDD – 1.5V 15-bit ±32,768 35 8-bit parallel -25 to +70 Highest conversion speed (40 conv/sec) 44-pin PLCC, 40-pin PDIP
TC14433 BCD A/D ±4.5 to ±8 ±199.9 mV to 1.999V 3½ ±2,000 20 MUXed BCD -40 to +85 For DMM, DPM, Data loggers 24-pin SOIC, 24-pin PDIP,
28-pin PLCC
TC14433A BCD A/D ±4.5 to ±8 ±199.9 mV to 1.999V 3½ ±2,000 20 MUXed BCD -40 to +85 For DMM, DPM, Data loggers 24-pin PDIP, 28-pin PLCC
Analog and Interface Product Selector Guide 22
MIXED SIGNAL – Digital Potentiometers (Continued)
Part # Number
of Taps Memory Number per
Package Interface Resistance
(kOhms) INL
(max) DNL
(max) Temperature
Range (°C) Comments Packages
MCP4131 128 Volatile 1 SPI 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN
MCP4132 128 Volatile 1 SPI 5, 10, 50, 100 0.8 0.25 -40 to +125 Rheostat mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN
MCP4231 128 Volatile 2 SPI 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, Shutdown, WiperLock™ Technology 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP, 16-pin 4x4 QFN
MCP4232 128 Volatile 2 SPI 5, 10, 50, 100 0.8 0.25 -40 to +125 Rheostat mode, Shutdown 10-pin MSOP, 10-pin 3x3 DFN
MCP41010 256 Volatile 1 SPI 10 1 1 -40 to +85 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC
MCP41050 256 Volatile 1 SPI 50 1 1 -40 to +85 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC
MCP41100 256 Volatile 1 SPI 100 1 1 -40 to +85 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC
MCP4151 256 Volatile 1 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN
MCP4152 256 Volatile 1 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN
MCP4161 256 Nonvolatile 1 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN
MCP4162 256 Nonvolatile 1 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN
MCP42010 256 Volatile 2 SPI 10 1 1 -40 to +85 Potentiometer mode, Shutdown 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP42100 256 Volatile 2 SPI 100 1 1 -40 to +85 Potentiometer mode, Shutdown 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
MCP4251 256 Volatile 2 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode, Shutdown, WiperLock™ Technology 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP, 16-pin 4x4 QFN
MCP4252 256 Volatile 2 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode, Shutdown 10-pin MSOP, 10-pin 3x3 DFN
MCP4261 256 Nonvolatile 2 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode, Shutdown, WiperLock™ Technology 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP, 16-pin 4x4 QFN
MCP4262 256 Nonvolatile 2 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode, Shutdown 10-pin MSOP, 10-pin 3x3 DFN
MCP4341 129 Nonvolatile 4 I2C™ 5, 10, 50, 100 0.8 0.375 -40 to +125 7-bit, Volatile potentiometer with an I2C interface 20-pin TSSOP, 20-pin 4x4 QFN
MCP4342 129 Nonvolatile 4 I2C™ 5, 10, 50, 100 0.8 0.375 -40 to +125 7-bit, Volatile rheostat with an I2C interface 14-pin TSSOP
MCP4361 257 Nonvolatile 4 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 8-bit, Non-volatile potentiometer with an I2C interface 20-pin TSSOP, 20-pin 4x4 QFN
MCP4362 257 Nonvolatile 4 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 8-bit, Non-volatile rheostat with an I2C interface 14-pin TSSOP
MCP4331 129 Volatile 4 I2C™ 5, 10, 50, 100 0.8 0.375 -40 to +125 7-bit, Volatile potentiometer with an I2C interface 20-pin TSSOP, 20-pin 4x4 QFN
MCP4332 129 Volatile 4 I2C™ 5, 10, 50, 100 0.8 0.375 -40 to +125 7-bit, Volatile rheostat with an I2C interface 14-pin TSSOP
MCP4351 257 Volatile 4 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 8-bit, Non-volatile potentiometer with an I2C interface 20-pin TSSOP, 20-pin 4x4 QFN
MCP4352 257 Volatile 4 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 8-bit, Non-volatile rheostat with an I2C interface 14-pin TSSOP
MCP4441 129 Nonvolatile 4 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, WiperLock™ Technology 20-pin TSSOP, 20-pin 4x4 QFN
MCP4442 129 Nonvolatile 4 I2C™ 5, 10, 50, 101 0.8 0.375 -40 to +125 Rheostat mode, WiperLock™ Technology 14-pin TSSOP
MCP4461 257 Nonvolatile 4 I2C™ 5, 10, 50, 102 1 0.5 -40 to +125 Potentiometer mode, WiperLock™ Technology 20-pin TSSOP, 20-pin 4x4 QFN
MCP4462 257 Nonvolatile 4 I2C™ 5, 10, 50, 103 1 0.5 -40 to +125 Rheostat mode, WiperLock™ Technology 14-pin TSSOP
MCP4531 128 Volatile 1 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode 8-pin MSOP
MCP4631 128 Volatile 2 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode 14-pin TSSOP, 16-pin 4x4 QFN
MCP4541 128 Nonvolatile 1 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, WiperLock™ Technology 8-pin MSOP
MCP4641 128 Nonvolatile 2 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, WiperLock™ Technology 14-pin TSSOP, 16-pin 4x4 QFN
MCP4551 256 Volatile 1 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode 8-pin MSOP
MCP4651 256 Volatile 2 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode 14-pin TSSOP, 16-pin 4x4 QFN
MCP4561 256 Nonvolatile 1 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode, WiperLock™ Technology 8-pin MSOP
Analog and Interface Product Selector Guide 23
MIXED SIGNAL – Digital Potentiometers (Continued)
Part # Number
of Taps Memory Number per
Package Interface Resistance
(kOhms) INL
(max) DNL
(max) Temperature
Range (°C) Comments Packages
MCP4661 256 Nonvolatile 2 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode, WiperLock™ Technology 14-pin TSSOP, 16-pin 4x4 QFN
MCP4532 128 Nonvolatile 1 I2C™ 5, 10, 50, 100 0.8 0.375 -40 to +125 Rheostat mode 8-pin MSOP, 8-pin 3x3 DFN
MCP4632 128 Nonvolatile 2 I2C™ 5, 10, 50, 100 0.8 0.375 -40 to +125 Rheostat mode 10-pin MSOP, 10-pin 3x3 DFN
MCP4542 128 Nonvolatile 1 I2C™ 5, 10, 50, 100 0.8 0.375 -40 to +125 Rheostat mode, WiperLock™ Technology 8-pin MSOP, 8-pin 3x3 DFN
MCP4642 128 Nonvolatile 2 I2C™ 5, 10, 50, 100 0.8 0.375 -40 to +125 Rheostat mode, WiperLock™ Technology 10-pin MSOP, 10-pin 3x3 DFN
MCP4552 256 Nonvolatile 1 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode 8-pin MSOP, 8-pin 3x3 DFN
MCP4652 256 Nonvolatile 2 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode 10-pin MSOP, 10-pin 3x3 DFN
MCP4562 256 Nonvolatile 1 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode, WiperLock™ Technology 8-pin MSOP, 8-pin 3x3 DFN
MCP4662 256 Nonvolatile 2 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode, WiperLock™ Technology 10-pin MSOP, 10-pin 3x3 DFN
MIXED SIGNAL – D/A Converters
Part # Resolution
(Bits) DACs per
Package Interface VREF Output Settling
Time (μs) DNL
(LSB) Typical Standby Cur-
rent (μA) Typical Operating
Current (μA) Temperature Range
(°C) Packages
TC1320 8 1 SMbus Ext 10 ±0.8 0.1 350 -40 to +85 8-pin MSOP, 8-pin SOIC
TC1321 10 1 SMbus Ext 10 ±2 0.1 350 -40 to +85 8-pin MSOP, 8-pin SOIC
MCP4706 8 1 I2C™ Ext 6 0.05 0.06 210 -40 to +125 6-pin SOT-23
MCP4716 10 1 I2C™ Ext 6 0.188 0.06 210 -40 to +125 6-pin SOT-23
MCP4725 12 1 I2C™ VDD 6 0.75 1 210 -40 to +125 6-pin SOT-23
MCP4726 12 1 I2C™ Ext 6 0.75 0.06 210 -40 to +125 6-pin SOT-23
MCP4728 12 4 I2C™ Int/VDD 6 0.75 0.04 800 -40 to +125 10-pin MSOP
MCP4801 8 1 SPI Int 4.5 0.5 0.3 330 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin DFN
MCP4802 8 2 SPI Int 4.5 0.5 3.3 415 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP4811 10 1 SPI Int 4.5 0.5 0.3 330 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin DFN
MCP4812 10 2 SPI Int 4.5 0.5 3.3 415 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP4821 12 1 SPI Int 4.5 1 0.3 330 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin DFN
MCP4822 12 2 SPI Int 4.5 1 3.3 415 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP
MCP4901 8 1 SPI Ext 4.5 0.5 3.3 175 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin DFN
MCP4902 8 2 SPI Ext 4.5 0.5 0.3 350 -40 to +125 14-pin PDIP, 14-pin SOIC, 14-pinTSSOP
MCP4911 10 1 SPI Ext 4.5 0.5 3.3 175 -40 to +125 8-pin DFN, 8-pin MSOP, 8-pin PDIP, 8-pin SOIC
MCP4912 10 2 SPI Ext 4.5 0.5 0.3 350 -40 to +125 14-pin PDIP, 14-pin SOIC, 14-pinTSSOP
MCP4921 12 1 SPI Ext 4.5 0.75 3.3 175 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin DFN
MCP4922 12 2 SPI Ext 4.5 0.75 0.3 350 -40 to +125 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
Note: The analog output is voltage.
MIXED SIGNAL –
Frequency-to-Voltage/Voltage-to-Frequency Converters
Part # Frequency Range (kHz) Full Scale (ppm FS/°C) Non-linearity (%FS) Temperature Range (°C) Packages
TC9400 100 ±40 ±0.05 -40 to +85 14-pin PDIP, 14-pin SOIC
TC9401 100 ±40 ±0.02 -40 to +85 14-pin PDIP, 14-pin SOIC
TC9402 100 ±100 ±0.25 -40 to +85 14-pin PDIP, 14-pin SOIC
Analog and Interface Product Selector Guide 24
INTERFACE
INTERFACE – Controller Area Network (CAN) Products
Part # Operating
Voltage (V) Temperature
Range (°C) Tx
Buffers Rx
Buffers Filters Masks Interrupt
Output Unique Features Packages
MCP2510
(1)
2.7 to 5.5 -40 to +125 3 2 6 2 Yes CAN 2.0B Active controller with SPI interface to MCU, 3 transmit
buffers, 2 receive buffers, HW and SW message triggers 18-pin PDIP, 18-pin SOIC, 20-pin TSSOP
MCP2515 2.7 to 5.5 -40 to +125 3 2 6 2 Yes MCP2510 pin compatible upgrade with enhanced features
including higher throughput and data byte fi ltering 18-pin PDIP, 18-pin SOIC, 20-pin TSSOP
MCP25020 2.7 to 5.5 -40 to +125 3 2 2 1 N/A CAN 2.0B Active I/O Expander, Confi gurable I/O, 2 PWM outputs 14-pin PDIP, 14-pin SOIC
MCP25025 2.7 to 5.5 -40 to +85 3 2 2 1 N/A CAN 2.0B Active I/O Expander, Confi gurable I/O,
2 PWM outputs, One-wire CAN option 14-pin PDIP, 14-pin SOIC
MCP25050 2.7 to 5.5 -40 to +125 3 2 2 1 N/A Mixed-Signal CAN 2.0B Active I/O Expander, Confi gurable I/O,
4 10-bit ADCs, 2 PWM outputs 14-pin PDIP, 14-pin SOIC
MCP25055 2.7 to 5.5 -40 to +85 3 2 2 1 N/A Mixed-Signal CAN 2.0B Active I/O Expander, Confi gurable I/O,
4 10-bit ADCs, 2 PWM outputs, One-wire CAN option 14-pin PDIP, 14-pin SOIC
MCP2551 4.5 to 5.5 -40 to +125 n/a n/a n/a n/a N/A High-speed CAN Transceiver (1 Mbps max. CAN bus
speed), ISO11898 compatible, Industry standard pinout 8-pin PDIP, 8-pin SOIC
Note 1: Not recommended for new designs.
INTERFACE – Passive Access Products
Part # Operating
Voltage (V)
Operating
Temperature
Range (°C)
Bus
Type RF Carrier
Frequency Data Format Features Packages
MCP2030 1.8 to 3.6 -40 to +85 SPI 125 kHz NRZ Three axis signal conditioning devices for passive access
applications, High-sensitivity, Confi gurable smart wake-up fi lter 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
INTERFACE – Infrared Products
Part # Operating
Voltage (V) Operating
Temperature Range (°C) Max. Baud Rate
(Kbaud) Unique Features Packages
MCP2120 2.5 to 5.5 -40 to +85 325 UART to IR encoder/decoder with both hardware and software baud rate selection 14-pin PDIP, 14-pin SOIC
MCP2122 1.8 to 5.5 -40 to +85 16x less than clock input UART to IR encoder/decoder 8-pin PDIP, 8-pin SOIC
MCP2140A 2.0 to 5.5 -40 to +85 9.6 IrDA
®
Standard protocol handler plus bit encoder/decoder, Fixed baud rate, Low-cost 18-pin PDIP, 18-pin SOIC, 20-pin SSOP
MCP2150 3.0 to 5.5 -40 to +85 115.2 IrDA
®
Standard protocol handler plus bit encoder/decoder on one chip for DTE
applications, Programmable ID 18-pin PDIP, 18-pin SOIC, 20-pin SSOP
MCP2155 3.0 to 5.5 -40 to +85 115.2 IrDA
®
Standard protocol handler plus bit encoder/decoder on one chip for DCE
applications, Programmable ID 18-pin PDIP, 18-pin SOIC, 20-pin SSOP
IrDA
®
is a registered trademark of Infrared Data Association
INTERFACE – Ethernet Products
Part # Operating
Voltage (V) Operating Temperature
Range (°C) MAC PHY TX/RX RAM Interface Features Packages
ENC28J60 3.1 to 3.6 -40 to +85 Yes 10Base-T 8 KB SPI - 10Base-T Ethernet controller, IEEE 802.3™ compliant
- Loopback test modes, Auto-polarity detection
- Clock out pin with programmable frequencies
28-pin SOIC, 28-pin SSOP,
28-pin 6x6 QFN, 28-pin SPDIP
ENC424J600 3.0 to 3.6 -40 to +85 Yes 10/100Base-T 24 KB - SPI
- 8-bit multiplexed
parallel interface
- 10/100 Ethernet controller, IEEE 802.3(TM) compliant
- Cryptographic Security Engines - MD5, SHA-1, AES, RSA
- Preprogrammed unique MAC address
- Loopback test modes, Auto-polarity detection
- Clock out pin with programmable frequencies
44-pin TQFP, 44-pin QFN
ENC624J600 3.0 to 3.6 -40 to +85 Yes 10/100Base-T 24 KB
- SPI
- 8-bit or 16-bit multiplexed
or demultiplexed parallel
interface
- 10/100 Ethernet controller, IEEE 802.3(TM) compliant
- Cryptographic Security Engines - MD5, SHA-1, AES, RSA
- Preprogrammed unique MAC address
- Loopback test modes, Auto-polarity detection
- Clock out pin with programmable frequencies
64-pin TQFP
Analog and Interface Product Selector Guide 25
INTERFACE – LIN Transceiver Products
Part # Description VREG Output
Voltage (V) Operating
Temperature
Range (°C) VREG Output
Current (mA) Vcc Range
(V) Max
Baud Rate LIN Specifi cation
Supported Packages
MCP201 LIN Transceiver with integrated VREG 5.0 ±5% -40 to +125 50 6 to 18(1) 20 Kbaud Revision 1.2 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN
MCP2003 Stand-Alone LIN Transceiver (industry
standard pinout) None -40 to +125 None 6 to 27(1) 20 Kbaud Revision 1.3, 2.0, 2.1,
SAE J2602 8-pin PDIP, 8-pin SOIC, 8-pin 4x4 DFN
MCP2004 Stand-Alone LIN Transceiver with
TXE/Fault I/O None -40 to +125 None 6 to 27(1) 20 Kbaud Revision 1.3, 2.0, 2.1,
SAE J2602 8-pin PDIP, 8-pin SOIC, 8-pin4x4 DFN
MCP2021 LIN Transceiver with integrated VREG 5.0 ± 3%
3.3 ± 3% -40 to +125 50 6 to 18(1) 20 Kbaud Revision 1.3, 2.0, 2.1,
SAE J2602 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN, 8-pin
6x5 DFN
MCP2022 LIN Transceiver with integrated VREG,
RESET pin 5.0 ± 3%
3.3 ± 3% -40 to +125 50 6 to 18(1) 20 Kbaud Revision 1.3, 2.0, 2.1,
SAE J2602 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP
Note 1: Can withstand 40V load dump.
INTERFACE – Stand-alone RF Receiver Products
Part # Modulation Data Rate (kbps) Frequency
Range (MHz) Sensitivity (dBm) IF Frequency Range
(MHz) Operating Voltage (V) RSSI Selectable LNA Gain Packages
rfRXD0420 ASK, FSK, FM 80 300 to 450 -111 0.455 to 21.4 2.5 to 5.5 Yes Yes 32-pin LQFP
rfRXD0920 ASK, FSK, FM 80 800 to 930 -109 0.455 to 21.4 2.5 to 5.5 Yes Yes 32-pin LQFP
INTERFACE – IEEE 802.15.4 ZigBee® RF Transceiver Products
Part # Frequency
Range (GHz) Sensitivity
(dBm) Power
Output
(dBm) RSSI TX Power
Consumption
(mA)
RX Power
Consumption
(mA) Clock
(MHz) Sleep MAC MAC
Features Encryption Interface Pin
Count Packages
MRF24J40 2.405-2.48 -95 0 Yes 18 22 20 Yes Yes CSMA-CA AES128 4-wire SPI 40 40-pin QFN
MRF24J40MA 2.405-2.48 -95 0 Yes 23 19 20 Yes Yes CSMA-CA AES128 4-wire SPI 12 Module
MRF24J40MB 2.405-2.48 -102 20 Yes 120 25 20 Yes Yes CSMA-CA AES128 4-wire SPI 12 Module
MRF49XA 433/868/915 -110 7 Yes 15 11 – Yes – – – 4-wire SPI 16 16-pin TSSOP
INTERFACE – USB Products
Part # USB Speed USB Compliant PHY MCU Interface Tx/Rx Buffer Size (bytes) Number of GPIO Operating Voltage (V) Packages
MCP2200 Full-Speed USB (12 Mb/s),
Low-Speed USB (1.5 Mb/s) Yes Yes UART 128/128 8 2.7 to 5.5 20-pin SOIC, 20-pin TSSOP, 20-pin QFN
INTERFACE – Serial Peripherals
Part # Description Operating
Voltage (V) Operating
Temperature
Range (°C) Bus
Type Max. Bus
Frequency
(kHz) Features Packages
MCP23008 8-bit I/O Port Expander 1.8 to 5.5 -40 to +85 I2C™ 1700 3 HW address pins, HW interrupt, 25 mA source/sink capability per I/O 18-pin PDIP, 18-pin SOIC, 20-pin SSOP, 20-pin 4x4 QFN
MCP23S08 8-bit I/O Port Expander 1.8 to 5.5 -40 to +85 SPI 10000 2 HW address pins, HW interrupt, 25 mA source/sink capability per I/O 18-pin PDIP, 18-pin SOIC, 20-pin SSOP, 20-pin 4x4 QFN
MCP23009 8-bit I/O Port Expander 1.8 to 5.5 -40 to +125 I2C™ 3400 1 HW address pin, HW interrupt, 25 mA source/sink per I/O, 100 kHz, 400 kHz
and 3.4 MHz I2C™ supported 18-pin PDIP, 18-pin SOIC, 20-pin SSOP
MCP23S09 8-bit I/O Port Expander 1.8 to 5.5 -40 to +125 SPI 10000 HW interrupt, 25 mA source/sink per I/O 18-pin PDIP, 18-pin SOIC
MCP23016 16-bit I/O Port Expander 2.0 to 5.5 -40 to +85 I2C™ 400 3 HW address inputs, HW interrupt, 25 mA source/sink capability per I/O 28-pin PDIP, 28-pin SOIC, 28-pin SSOP, 28-pin 6x6 QFN
MCP23017 16-bit I/O Expander 1.8 to 5.5 -40 to +125 I2C™ 1700 3 HW address pins, 25 mA sink/source per I/O, 100 kHz, 400 kHz and 3-4
MHz I2C™ supported, Interrupt output 28-pin PDIP, 28-pin SOIC, 28-pin SSOP, 28-pin QFN
MCP23S17 16-bit I/O Expander 1.8 to 5.5 -40 to +125 SPI 10000 3 HW address pins, 25 mA sink/source per I/O, Interrupt output 28-pin PDIP, 28-pin SOIC, 28-pin SSOP, 28-pin QFN
MCP23018 16-bit I/O Port Expander 1.8 to 5.5 -40 to +125 I2C™ 3400 1 HW address pin, 2 HW interrupts, 25 mA source/sink per I/O, 100 kHz, 400
kHz and 3.4 MHz I2C™ supported 24-pin SSOP, 28-pin SOIC, 28-pin SDIP
MCP23S18 16-bit I/O Port Expander 1.8 to 5.5 -40 to +125 SPI 10000 2 HW interrupts, 25 mA source/sink per I/O 28-pin SOIC, 28-pin SDIP
Analog and Interface Product Selector Guide 26
SAFETY & SECURITY – Ionization Smoke Detector ICs
Part # Horn Driver Alarm Pattern Alarm
Memory Low Battery
Detection Reverse Battery
Protection Alarm
Interconnect Hush
Timer Power-up
Low Battery Test Operating Temperature
Range (°C) Packages
RE46C120 NFPA Temporal or Continuous Tone No Yes Yes – – – -10 to +60 16-pin PDIP
RE46C121 NFPA Temporal No Yes Yes Yes – – -10 to +60 16-pin PDIP
RE46C122 NFPA Temporal No Yes Yes Yes Yes Yes -10 to +60 16-pin PDIP
RE46C126 Continuous Tone No Yes Yes Yes – – -10 to +60 16-pin PDIP
RE46C127 Continuous Tone No Yes Yes Yes Yes Yes -10 to +60 16-pin PDIP
RE46C128 NFPA Temporal No Yes Yes Yes – Yes -10 to +60 16-pin PDIP
RE46C129 Continuous Tone No Yes Yes Yes – Yes -10 to +60 16-pin PDIP
RE46C152 NFPA Temporal or Continuous Tone No Yes Yes Yes Yes Yes -10 to +60 16-pin PDIP
RE46C162 NFPA Temporal or Continuous Tone Yes Yes Yes Yes Yes Yes -10 to +60 16-pin PDIP
RE46C163 NFPA Temporal or Continuous Tone Yes Yes Yes Yes Yes Yes -10 to +60 16-pin PDIP
RE46C180 NFPA Temporal or Continuous Tone Yes Yes No Yes Yes Yes -10 to +60 16-pin PDIP, 16-pin SOIC
SAFETY & SECURITY – Ionization Smoke Detector Front Ends
Part # Microprocessor Compatible Output Output Options Typical Application Operating Temperature Range (°C) Packages
RE46C112 Yes VOUT 1/4 of VDD or VOUT 1/4 of Detect Input 3V or 3.3V Microprocessor -10 to +60 8-pin PDIP
RE46C114 Yes VOUT 1/2 of VDD or VOUT 1/2 of Detect Input 5V Microprocessor -10 to +60 8-pin PDIP
SAFETY & SECURITY – Piezoelectric Horn Drivers
Part # Operating
Voltage (V) Piezoelectric Horn
Driver LED Driver Voltage
Regulator (V) Low Battery
Detection Interconnect Power good Operating
Temperature Range (°C) Packages
RE46C100 6 to 16 Yes – – – – – -40 to +85 8-pin PDIP, 8-pin SOIC
RE46C101 6 to 16 Yes Yes – – – – -40 to +85 8-pin PDIP, 8-pin SOIC
RE46C104 4 to 8 Yes – – – – – 0 to +50 14-pin PDIP, 14-pin SOIC
RE46C105 6 to 12 Yes Yes 3.3 or 5 Yes – – -40 to +85 14-pin PDIP, 14-pin SOIC
RE46C107 2 to 5 Yes Yes 3 or 3.3 Yes – – 0 to +50 16-pin PDIP, 16-pin SOIC
RE46C108 6 to 12 Yes – 3.3 or 5 – – – -40 to +85 8-pin PDIP, 8-pin SOIC
RE46C109 6 to 12 Yes – 3 Yes Yes Yes -40 to +85 16-pin PDIP, 16-pin SOIC
RE46C117 2 to 5 Yes – – – – – 0 to +50 8-pin PDIP, 8-pin SOIC
RE46C119 6 to 12 Yes – 3 Yes Yes Yes -40 to +85 16-pin PDIP, 16-pin SOIC
SAFETY & SECURITY
SAFETY & SECURITY – Photoelectric Smoke Detector ICs
Part # Horn Driver
Alarm Pattern Alarm
Memory Low Battery
Detection Chamber
Test Alarm
Interconnect Sensitivity
Timer Internal
POR Alternate
Diagnostic Mode Operating
Temperature Range (°C) Packages
RE46C140 NFPA Temporal No Yes Yes Yes Yes Yes – -25 to +75 16-pin PDIP, 16-pin SOIC
RE46C141 NFPA Temporal No Yes Yes Yes – Yes – -25 to +75 16-pin PDIP, 16-pin SOIC
RE46C143 Continuous Tone No Yes Yes Yes – Yes – -25 to +75 16-pin PDIP, 16-pin SOIC
RE46C144 Continuous Tone No Yes Yes Yes Yes Yes – -25 to +75 16-pin PDIP, 16-pin SOIC
RE46C145 NFPA Temporal No Yes Yes Yes Yes Yes Yes -25 to +75 16-pin PDIP, 16-pin SOIC
RE46C165 NFPA Temporal Yes Yes Yes Yes Yes Yes Yes -25 to +75 16-pin PDIP, 16-pin SOIC
RE46C166 Continuous Tone Yes Yes Yes Yes Yes Yes Yes -25 to +75 16-pin PDIP, 16-pin SOIC
RE46C167 NFPA Temporal Yes Yes Yes Yes Yes Yes Yes -25 to +75 16-pin PDIP, 16-pin SOIC
RE46C168 Continuous Tone Yes Yes Yes Yes Yes Yes Yes -25 to +75 16-pin PDIP, 16-pin SOIC
RE46C190 NFPA Temporal or
Continuous Tone No Yes Yes Yes Yes Yes – -10 to +60 16-pin SOIC
ANALOG DESIGN DEVELOPMENT TOOLS
Evaluation, Demonstration and Development Kits
Order # Description Devices Supported
Thermal Management Demonstration and Evaluation Tools
TMPSNS-RTD1 PT100 RTD Evaluation Board MCP6S26, MCP3301, MCP6024, MCP41010,
PIC18F2550, TC1071, MCP6002
MCP9700DM-PCTL
MCP9700 Temperature-to-Voltage Converter PICtail™ Demonstration Board
MCP9800
MCP9700DM-TH1 MCP9700 Thermistor Demonstration Board MCP9700, MCP6S92
MCP9800DM-PCTL MCP9800 Temperature Sensor PICtail™ Demonstration Board MCP9800
MCP9800DM-TS1 MCP9800 Temperature Sensor Demonstration Board MCP9800
MCP9800DM-DL MCP9800 Temperature Data Logger Demonstration Board MCP9800
MCP9800DM-DL2 MCP9800 Temperature Data Logger Demonstration Board 2 MCP9800, MCP101, PIC10F202, 24LC16B
TC72DM-PICTL TC72 Digital Temperature Sensor PICtail™ Demonstration Board TC72
TC74DEMO TC74 Serial Digital Thermal Sensor Demonstration Board TC74
TC77DM-PICTL TC77 Thermal Sensor PICtail™ Demonstration Board TC77
TC642DEMO TC64X/64XB Fan Speed Controller Demonstration Board TC642, TC646, TC647, TC648, TC649
TC650DEMO TC650 Fan Controller Demonstration Board TC650
TC652DEMO TC652 Fan Controller Demonstration Board TC652
TC1047ADM-PICTL TC1047A Temperature-to-Voltage Converter PICtail™ Demonstration Board TC1047A
TMPSNSRD-TCPL1 Thermocouple Reference Design MCP9804, MCP3421
TMPSNSRD-RTD2 RTD Reference Design Board MCP3551, MCP9804
Mixed Signal Demonstration and Evaluation Tools
ADM00333 PIC18F87J72 Evaluation Board PIC18F87J72
ARD00280 PIC18F87J72 Single Phase Energy Meter Reference Design n/a
ARD00330 PIC18F87J72 Energy Monitoring PICtail Plus Daughter Board n/a
DV3201A MCP3XXX Single/Dual ADC MXDEV® Daughter Board MCP3001, MCP3002, MCP3201, MCP3202
DV3204A MCP3204/08 MXDEV® Daughter Board MCP3004, MCP3008, MCP3204, MCP3208
MCP2030DM-TPR MCP2030 Bidirectional Communications Demonstration Kit MCP2030, MCP3421, PIC16F636, TC4421, PIC18F4680
MCP3421EV MCP3421 SOT-23-6 Evaluation Board MCP3421
MCP3421DM-BFG MCP3421 Battery Fuel Gauge Demo Board MCP3421, MCP73831, MCP1702, PIC18F4550
MCP3422EV MCP3422 Evaluation Board MCP3422
MCP3423EV MCP3423 Evaluation Board MCP3423
MCP3424EV MCP3424 Evaluation Board MCP3424
MCP3425EV MCP3425 SOT 23-6 Evaluation Board MCP3425
MCP3221DM-PCTL MCP3221 PICtail™ Demonstration Board MCP3221
MCP3551DM-PCTL MCP3551 Delta-Sigma ADC Demonstration Board MCP3551
MCP355XDV-MS1 MCP355X Sensor Application Developer’s Board MCP3551, MCP3553, MCP3550-50, MCP3550-60
MCP355XDM-TAS MCP355X Tiny Application Sensor Demonstration Board MCP3551, MCP3553, MCP3550-50, MCP3550-60
MCP3901EV-MCU16 MCP3901 ADC Evaluation Board for 16-bit MCUs MCP3901, PIC24F, PIC24H, dsPIC33, PIC18F86J55
MCP3905EV MCP3905 Energy Meter Evaluation Board MCP3905
MCP3905RD-PM1 MCP3905 Energy Meter Reference Design MCP3905
MCP3909EV-MCU16 MCP3909 ADC Evaluation Board for 16-bit MCUs MCP3909
MCP3909RD-3PH1 MCP3909 3-Phase Energy Meter Reference Design MCP3909, PIC18F2520, PIC18F4550
MCP3909RD-3PH3 MCP3909 and dsPIC33F 3-Phase Energy Meter Reference Design MCP3909, dsPIC33FJ128GP706
MCP3909RD-PM1 MCP3909 and PIC18F25K20 Low Cost Power Monitor Reference Design MCP3909, PIC18F25K20
MCP3909RD-1PH1 MCP3909 and PIC18F85J90 Single Phase Energy Meter Reference Design MCP3909, PIC18F85J90
MCP401XEV MCP401X Evaluation Board MCP40D18, MCP4017, MCP4018, MCP4019,
MCP40D17, MCP40D19
Analog and Interface Product Selector Guide 27
ANALOG DESIGN DEVELOPMENT TOOLS
28 Analog and Interface Product Selector Guide
Evaluation, Demonstration and Development Kits
Order # Description Devices Supported
Mixed Signal Demonstration and Evaluation Tools (Continued)
MCP3421DM-WS1 MCP3421 Weight Scale Demo Board MCP3421, MCP6V07, PIC18F4550
MCP402XEV MCP402X Non-Volatile Digital Potentiometer Evaluation Board MCP4021, MCP4022, MCP4023, MCP4024
MCP42XXEV MCP42XX Evaluation Board MCP4231, MCP4241, MCP4251, MCP4261
MCP43XXEV MCP43XX Evaluation Board MCP4331, MCP4341, MCP4351, MCP4361
MCP4XXXDM-DB MCP4XXX Digital Potentiometer Daughter Board MCP4011, MCP4021, MCP42XXX
MCP42XXDM-PTPLS MCP42XX PICtail™ Plus Daughter Board MCP4231, MCP4232, MCP4241, MCP4242, MCP4251,
MCP4252, MCP4261, MCP4262
MCP46XXDM-PTPLS MCP46XX PICtail™ Plus Daughter Board MCP4631, MCP4641, MCP4651, MCP47652, MCP4661,
MCP4662
MCP46XXEV MCP46XX Evaluation Board MCP4631, MCP4641, MCP4651, MCP4661
MCP4725EV MCP4725 SOT 23-6 Evaluation Board MCP4725
MCP4725DM-PTPLS MCP4725 PICtail™ Plus Daughter Board MCP4725
MCP4728EV MCP4728 Quad DAC Evaluation Board MCP4728
ADM00310 MCP3903 ADC Evaluation Board for 16-bit MCUs MCP3903, MCP2200, PIC24, dsPIC33
DV42XXX MCP42XXX Digital Potentiometer Evaluation Board MCP42010, MCP42050, MCP42100
DVMCPA MXDEV® Analog Evaluation System MCP3001/02, MCP3004/08, MCP3201/08,
MCP3204/08
MXSIGDM Mixed Signal PICtail™ Demonstration Board TC132X, MCP330X, MCP320X, MCP482X, MCP492X,
MCP3221, MCP3021, MCP1525
Power Management Demonstration and Evaluation Tools
MCP1252DM-BKLT MCP1252 Charge Pump Backlight Demonstration Board MCP1252
MCP1256/7/8/9EV MCP1256/7/8/9 Charge Pump Evaluation Board MCP1256, MCP1257, MCP1258, MCP1259
MCP1601EV MCP1601 Buck Regulator Evaluation Board MCP1601
MCP1602EV MCP1602 Evaluation Board MCP1602
MCP1603EV MCP1603 Buck Converter Evaluation Board MCP1603
MCP1603RD-TNY MCP1603 Tiny Reference Design MCP1603
MCP1612EV MCP1612 Synchronous Buck Regulator Evaluation Board MCP1612
MCP1630RD-DDBK1 MCP1630 +12V in Dual Output Buck Converter Reference Design MCP1630
MCP1630RD-DDBK3 MCP1630 Bidirectional 4-Cell Li-Ion Charger Reference Design MCP1630V, PIC16F88, MCP6022
MCP1630RD-NMC1 MCP1630 Low-Cost NiMH Battery Charger Reference Design MCP1630, PIC12F683, MCP6292, MCP1702
MCP1630DM-DDBK1 MCP1630 1A Bias Supply Demonstration Board MCP1630
MCP1630DM-DDBS1 MCP1630 Automotive Input Boost Converter Demonstration Board MCP1630, PIC12F683
MCP1630DM-LED2 MCP1630 Boost Mode LED Driver Demonstration Board MCP1630V, PIC12F683, MCP1702
MCP1630RD-LIC1 MCP1630 Li-Ion Multi Bay Battery Charger Reference Design MCP1630
MCP1630RD-LIC2 MCP1630 Low Cost Li-Ion Battery Charger Reference Design MCP1630
MCP1630DM-NMC1 MCP1630 NiMH Battery Charger Demonstration Board MCP1630
MCP1630DM-DDBS2 MCP1630 Coupled Inductor Boost Demonstration Board MCP1630, PIC12F683
MCP1630DM-DDBK4 MCP1630 Automotive Input, Triple Output Converter Demonstration Board MCP1630, PIC12F683
MCP1631RD-DCPC1 MCP1631HV Digitally Controlled Programmable Current Source
Reference Design MCP1631HV, PIC16F616
MCP1631RD-MCC1 MCP1631HV Multi-Chemistry Battery Charger Reference Design MCP1631HV, PIC16F883
MCP1631RD-MCC2 MCP1631HV Multi-Chemistry Battery Charger Reference Design MCP1631HV, PIC16F883
MCP1640EV-SBC MCP1640 Sync Boost Converter Evaluation Board MCP1640
MCP1640RD-4ABC MCP1640 Single Quad-A Battery Boost Converter Reference Design MCP1640, PIC12F617
Analog and Interface Product Selector Guide 29
ANALOG DESIGN DEVELOPMENT TOOLS
Evaluation, Demonstration and Development Kits
Order # Description Devices Supported
Power Management Demonstration and Evaluation Tools (Continued)
MCP1650DM-LED1 MCP1650 3W White LED Demonstration Board MCP1650
MCP1650DM-LED2 MCP1650 Multiple White LED Demonstration Board MCP1650
MCP1650EV MCP1650 Boost Controller Evaluation Board MCP1650
MCP1650DM-DDSC1 MCP1650 SEPIC Power Supply Demonstration Board MCP1650
MCP1726EV MCP1726 1A LDO Evaluation Board MCP1726
MCP73113EV-1SOVP MCP73113 OVP Single Cell Li-Ion Battery Charger Evaluation Board MCP73113, MCP73114
MCP73213EV-2SOVP MCP73213 OVP Dual Cell Li-Ion Battery Charger Evaluation Board MCP73213
MCP73X23EV-LFP MCP73X23 OVP Lithium Iron Phosphate Battery Charger Evaluation Board MCP73123, MCP73223
MCP73871DM-VPCC MCP73871 Demo Board with Voltage Proportional Current Control MCP73871
MCP7381XEV MCP7381X Low-Cost Li-Ion Battery Charger Evaluation Board MCP73811, MCP73812
MCP7382XEV MCP7382X Li-Ion Battery Charger Evaluation Board MCP7382X
MCP73831EV MCP73831 Evaluation Kit MCP73831
MCP73833EV MCP73833 Li-Ion Battery Charger Evaluation Board MCP73833, MCP73834
MCP7383XEV-DIBC MCP73837/8 AC/USB Dual Input Battery Charger Evaluation Board MCP73837, MCP73838
MCP7383XRD-PPM MCP7383X Li-Ion System Power Path Management Reference Design MCP73831, MCP73832, MCP73833, MCP73834
MCP7384XEV MCP7384X Li-Ion Battery Charger Evaluation Board MCP7384X
MCP73855EV MCP73855 Li-Ion Battery Charger Evaluation Board MCP73855
MCP7386XEV MCP7386X Li-Ion Battery Charger Evaluation Board MCP7386X
MCP73871EV MCP73871 Evaluation Board MCP73871
SOT23-3EV-VREG SOT23-3 Voltage Regulator Evaluation Board MCP1701A, MCP1702, MCP1703
SOT223-3EV-VREG SOT223-3 Voltage Regulator Evaluation Board MCP1791, MCP1824, MCP1825, MCP1826
SOT89-3EV-VREG SOT89-3 Voltage Regulator Evaluation Board MCP1700, MCP1701A, MCP1702, MCP1703
TO263-3EV-VREG TO220-3/TO263-3 Voltage Regulator Evaluation Board MCP1790, MCP1825S, MCP1826S, MCP1827S
SOT23-5EV-VREG SOT23-5 Voltage Regulator Evaluation Board MCP1801, MCP1802, TC1014/1015/1185, and other
SOT23-5 LDOs
SOT223-5EV-VREG SOT223-5 Voltage Regulator Evaluation Board MCP1790, MCP1824, MCP1825, MCP1826
TO263-5EV-VREG TO220-5/TO263-5 Voltage Regulator Evaluation Board MCP1790, MCP1791, MCP1825, MCP1826, MCP1827
TC110DM TC110 Boost Converter Demonstration Board TC110, MCP73832
TC115EV TC115 PFM/PWM Boost Converter Evaluation Board TC115
TC1016/17EV TC1016/17 LDO Linear Regulator Evaluation Board TC1016/17
TC1303BDM-DDBK1 TC1303B Demonstration Board TC1303B
TC1303DM-DDBK2 TC1303 DFN Adjustable Output Demonstration Board TC1303C
Interface Products Demonstration and Evaluation Tools
GPIODM-KPLCD GPIO Expander Keypad and LCD Demo Board MCP23008, MCP23S08, MCP23017, MCP23S17,
PIC18F4550, MCP1702
DV251001 MCP2510/2515 CAN Developer’s Kit MCP2515, MCP2510
DV250501 MCP250XX CAN I/O Expanders Developer’s Kit MCP25020, MCP25025, MCP25050, MCP25055
MCP2515DM-PCTL MCP2515 CAN Controller PICtail™ Demonstration Board MCP2515
MCP215XDM MCP215X Data Logger Demonstration Board MCP2150/55
MCP2140DM-TMPSNS MCP2140 IrDA® Wireless Temp Demonstration Board MCP2140
MCP212XDM MCP2120/22 Developer's Board MCP2120, MCP2122
MCP212XEV-DB MCP212X Developer’s Daughter Board MCP212X
ANALOG DESIGN DEVELOPMENT TOOLS
Evaluation, Demonstration and Development Kits
Order # Description Devices Supported
Interface Products Demonstration and Evaluation Tools (Continued)
MCP215X/40EV-DB MCP215X/40 Developer’s Daughter Board MCP2140, MCP2150/55
MCP2150DM MCP2150 Developer's Board MCP2150, MCP2155
MCP2200EV-VCP MCP2200 USB to RS232 Demonstration Board MCP2200
MCP23X08EV MCP23X08 8-bit GPIO Expander Evaluation Board MCP23008, MCP23S08
MCP23X17EV MCP23X17 16-bit GPIO Expander Evaluation Board MCP23017, MCP23S17
MCP2515DM-BM MCP2515 CAN Bus Monitor Demonstration Board MCP2515, MCP2551
MCP2515DM-PTPLS MCP2515 PICtail™ Plus Daughter Board MCP2515, MCP2551
PKSERIAL-SPI1 PICkit™ Serial SPI Demonstration Board 25LC020A, TC77, MCP3201, MCP4822, MCP41010,
MCP6S92, MCP23S08
PKSERIAL-I2C1 PICkit™ Serial I2C™ Demonstration Board 24LC02B, MCP9801, MCP3221, TC1321, MCP23008
Linear Demonstration and Evaluation Tools
MCP6031DM-PTPLS MCP6031 Photodiode PICtail™ Plus Demonstration Board MCP6031
MCP651EV-VOS MCP651 Input Offset Evaluation Board MCP651
MCP661DM-LD MCP661 Line Driver Demo Board MCP661, MCP662, MCP665
MCP6S22DM-PICTL MCP6S22 PGA PICtail™ Demonstration Board MCP6S22
MCP6S2XEV MCP6S2X PGA Evaluation Board MCP6S2X
MCP6SX2DM-PCTLPD MCP6SX2 PGA Photodiode PICtail™ Demonstration Board MCP6S22/92
MCP6SX2DM-PCTLTH MCP6SX2 PGA Thermistor PICtail™ Demonstration Board MCP6S22/92
MCP6V01DM-VOS MCP6V01 Input Offset Demonstration Board MCP6V01, MCP6V03, MCP6V06, MCP6V08
MCP6V01RD-TCPL MCP6V01 Thermocouple Auto-Zeroed Reference Design MCP6V01
PIC16F690DM-PCTLHS Humidity Sensor PICtail™ Demonstration Board MCP6291, PIC16F690
MCP6XXXEV-AMP1 MCP6XXX Amplifi er Evaluation Board 1 MCP6021
MCP6XXXEV-AMP2 MCP6XXX Amplifi er Evaluation Board 2 MCP6021
MCP6XXXEV-AMP3 MCP6XXX Amplifi er Evaluation Board 3 MCP6021
MCP6XXXEV-AMP4 MCP6XXX Amplifi er Evaluation Board 4 MCP6021
MCP6XXXDM-FLTR Active Filter Demonstration Board Kit MCP6271
Analog Blank Evaluation Boards
VSUPEV SOT-23-3 Voltage Supervisor Evaluation Board SOT-23-3 Devices
VSUPEV2 SOT-23-5/6 Voltage Supervisor Evaluation Board SOT-23-5, SOT-23-6 Devices
SC70EV SC70-6 and SOT-23-6/8 to DIP-8 Evaluation Board SC70-6/5/3, SOT-23-8/6/5/3, and DIP-8 Devices
SOIC8EV SOIC/MSOP/TSSOP/DIP 8-pin Evaluation Board 8-pin SOIC, MSOP, TSSOP, DIP Devices
SOIC14EV SOIC/TSSOP/DIP 14-pin Evaluation Board 14-pin SOIC, TSSOP, DIP Devices
TSSOP20EV 20-pin TSSOP and SSOP Evaluation Board TSSOP-20/16/14/8 and SSOP-20
Miscellaneous Analog Demonstration and Evaluation Tools
ADM00344 RE46C190 Demonstration Board RE46C190
EFIELDEV Electrical Field Evaluation Board N/A
HFIELDEV Magnetic Field Evaluation Board N/A
INTRFCEV PSRR and Digital Noise Evaluation Board N/A
30 Analog and Interface Product Selector Guide
Thermal Management Products
MCP9700 Thermistor Demo Board (MCP9700DM-TH1)
The MCP9700 Thermistor Demo Board contains
the analog circuitry to measure temperature. The
board uses BC Components’ 232264055103
NTC thermistor to convert temperature to
resistance. The thermistor is placed in a voltage
divider which converts resistance to voltage. This
voltage is filtered and placed at the MCP6S22
Programmable Gain Amplifier’s (PGA) CH0 input. The PGA
gains and buffers the thermistor.
PT100 RTD Evaluation Board (TMPSNS-RTD1)
This board demonstrates how to bias a
Resistive Temperature Detector (RTD)
and accurately measure temperature.
Up to two RTDs can be connected. The
RTDs are biased using constant current
source and the output voltage is scaled using a differential
amplifier. The output is then connected to a 12-bit
differential Analog-to-Digital Converter (ADC) MCP3301. The
ADC outputs serial data to a PIC18F2550 device using a
Serial Peripheral Interface (SPI). The data is transmitted to a
PC using a USB interface. A Microsoft Excel® macro is used
as a Graphical User Interface (GUI) to acquire the data. The
acquired data is stored in an Excel worksheet and graphed
as a real-time strip chart display.
MCP9800 Temperature Data Logger Demo Board
(MCP9800DM-DL)
Allows users to store up to 128,000
temperature readings from the MCP9800
sensor to the 24LC1025, Microchip’s
1024 Kbit EEPROM. A PIC16F684
MCU communicates with the sensor
and EEPROM. In addition, the PIC MCU interfaces to a PC
using the PICkit™ 1 Flash Starter Kit and transfers the
temperature readings from the EEPROM to the PC. Microsoft
Excel® can be used to view the data.
Mixed Signal Products
MCP3909 and PIC18F85J90 Single Phase Energy
Meter Reference Design (MCP3909RD-1PH1)
The MCP3909/PIC18F85J90 Single Phase
Energy Meter Reference Design is a fully
function single phase meter. The design is
intended to be low cost and is transformerless.
The design uses a half-wave rectified power
supply circuit and a shunt current sensing
element. A single MCP3909 acts as the
analog front end measurement circuitry. The PIC18F85J90
directly drives the LCD glass and displays active energy
consumption.
FEATURED ANALOG DEVELOPMENT TOOLS
MCP3421 Battery Fuel Gauge Demo Board
(MCP3421DM-BFG)
This board is used to demonstrate
the MCP3421 18-bit delta-sigma ADC
for battery fuel gauging applications.
It includes two MCP3421 devices,
MCP73831 (single cell Li-Ion/Li-Polymer Charger) and
PIC18F4550 MCU. The board measures: (1) the battery
voltage and (2) the current coming out from the battery in
the discharging mode and into the battery in the charging
mode using the ADC device (if charging mode is enabled
(optional)). It calculates the total fuel used and also fuel
remaining.
MCP4725 PICtail Plus Daughter Board
(MCP4725DM-PTPLS)
This daughter board demonstrates the
MCP4725 (12 bit DAC with non-volatile
memory) features using the Explorer 16
Development Board and the PICkit Serial
Analyzer.
MCP42XX PICtail Plus Daughter Board
(MCP42XXDM-PTPLS)
The MCP42XX PICtail Plus Daughter
Board is used to demonstrate the
operation of the MCP42XX Digital
Potentiometers. The operation of the
MCP41XX devices is similar to the MCP42XX devices.
Therefore, this demo board can be used as a development
platform for either device family. This board is designed to
be used in conjunction with either the PIC24 Explorer 16
Demo Board or the PICkit Serial Analyzer.
Power Management Products
MCP1631HV Multi-Chemistry Battery Charger
Reference Design (MCP1631RD-MCC1)
This reference design is a complete stand-alone
constant current battery charger for NiMH, NiCd
or constant current/constant voltage for Li-Ion
battery packs. When charging NiMH or NiCd
batteries, the reference design is capable of
charging one, two, three or four batteries connected in series
and one or two series batteries for Li-Ion. This board utilizes
the MCP1631HV (high-speed PIC MCU PWM TSSOP-20) and
PIC16F883 (28-pin SSOP).
MCP73871 Demo Board with Voltage Proportional
Current Control (MCP73871DM-VPCC)
The MCP73871 Demo Board with Voltage
Proportional Current Control is designed to
demonstrate Microchip’s stand-alone linear
Li-Ion battery charger with system power
path and load sharing management control
solution. The MCP73871 integrates the required elements
to meet design challenges when developing new Li-Ion/
Li-Polymer battery powered products.
T
A
t
d
EE
PR
OM
I
d
MCP73831 ( i l
MC
P4
1X
X
de
vi
ce
s
is
charging one
l ti Th
MC
Analog and Interface Product Selector Guide 31
LIN Serial Analyzer (APGDT001)
The LIN Serial Analyzer development
system enables a Personal Computer (PC)
to communicate with a LIN (Local Interface
Network) bus. The PC program uses a
graphical user interface to enter and
display message frames occurring on the target bus.
USB to UART Converter Evaluation Board
(MCP2200EV-VCP)
The USB to UART Converter Eval board
allows users to store up to 128,000
temperature readings from the MCP9800
sensor to the 24LC1025, Microchip’s
1024Kbit EEPROM. A PIC16F684 MCU
communicates with the sensor and EEPROM. In addition,
the PIC MCU interfaces to a PC using the PICkit 1 Flash
Starter Kit and transfers the temperature readings from the
EEPROM to the PC. Microsoft Excel can be used to view the
data.
Linear Products
MCP6V01 Thermocouple Auto-Zeroed
Ref Design Board (MCP6V01RD-TCPL)
The MCP6V01 design board demonstrates
how to use a difference amplifier
system to measure Electromotive Force
(EMF) voltage at the cold junction of
thermocouple in order to accurately measure temperature
of the thermocouple bead. This can be done by using the
MCP6V01 auto-zeroed op amp because of its ultra low
offset Voltage (VOS) and high Common Mode Rejection Ratio
(CMRR).
MCP651 Input Offset Evaluation Board
(MCP651EV-VOS)
The MCP651 Input Offset Evaluation
board is intended to provide a simple
means to measure the MCP651 Input
Offset Evaluation Board op amp’s input
offset voltage under a variety of operating
conditions. The measured input offset voltage (VOST)
includes the input offset voltage specified in the data sheet
(VOS) plus changes due to: power supply voltage (PSRR),
common mode voltage (CMRR), output voltage (AOL), input
offset voltage drift over temperature (ΔVOS/ΔTA) and 1/f
noise.
MCP6271 Active Filter Eval Kit (MCP6XXXDM-FLTR)
This kit supports active filters designed
by FilterLab® V2.0. These filters are all
pole and are built by cascading first and
second order sections. The kit includes:
one PCB designed to provide mid-supply
biasing to the other printed circuit boards,
four PCBs that support active filter designs with filter order
between n=1 and 8 (output test point for lab equipment
provided) and op amps, zero ohm jumpers, resistors and
capacitors that can be used to help build filters.
MCP73X23 OVP Lithium Iron Phosphate Battery
Charger Evaluation Board (MCP73X23EV-LFP)
The MCP73X23 Lithium Iron Phosphate
Battery Charger Evaluation board
demonstrates the features of Microchip’s
MCP73123 and MCP73223 Lithium Iron
Phosphate (LiFePO4) Battery Charge Management Controller
with Input Overvoltage Protection.
MCP7383X Li-Ion System Power Path Management
Reference Design (MCP7383XRD-PPM)
This reference design is developed to
assist product designers in reducing
product design cycle and time by
utilizing Microchip’s stand-alone Li-Ion
battery charge management controllers
with system power path management. Due to the natural
characteristics of Li-Ion/Li-Polymer batteries, they are the
most popular power sources for mobile devices, however,
extra care in design is always important. System Power Path
Management allows end-users to charge their batteries
without interruption.
MCP1640 Sync Boost Converter Evaluation Board
(MCP1640EV-SBC)
The MCP1640 Synchronous Boost Converter
Evaluation board demonstrates the MCP1640
in two boost-converter applications with
multiple output voltages. It can be used to
evaluate both package options (SOT-23-6 and
2x3-8 DFN). This board was developed to help
engineers reduce the product design cycle
time.
MCP1252 Charge Pump Backlight Demo Board
(MCP1252DM-BKLT)
The MCP1252 board demonstrates the
use of a charge pump device in an LED
application and acts as a platform to
evaluate the MCP1252 device in general.
Light intensity is controlled uniformly
through the use of ballast resistors. A PIC10F206 MCU
provides an enable signal to the MCP1252 and accepts a
push-button input that allows the white LEDs to be adjusted
to five different light intensities.
Interface Products
MCP2515 CAN Bus Monitor Demo Board
(MCP2515DM-BM)
The MCP2515 CAN Bus Monitor Demo
board kit contains two identical boards
which can be connected together to create
a simple two node Controller Area Network
(CAN) bus, which can be controlled and/
or monitored via the included PC interface. The board(s) can
also be connected to an existing CAN bus.
FEATURED ANALOG DEVELOPMENT TOOLS
T
t
through the use of
it
d
i
t
h
di l
thermocouple in o
co
nd
it
io
ns
Th
e
32 Analog and Interface Product Selector Guide
ANALOG PRODUCT PART NUMBERS
Part Number Suffix Designations
Ordering Information for all Microchip Analog Products beginning with “TC” prefix
(formerly TelCom Semiconductor Products)
TC 7106 A-60 1 C P L 713
Package Description # of Pins Package Description # of Pins
AB TO-220 3 MB SOT-89 3
AK TO-220 7 MF DFN (3x3) 8
AT TO-220 5 MT SOT-89 5
AV TO-220 (Formed) 5 NB SOT-23B 3
BB TO-220B 3 OA SOIC (N) 8
CB SOT-23A 3 OD SOIC (N) 14
CH SOT-23A 6 OE SOIC (W) 16
CT SOT-23A 5 OG SOIC (W) 24
DB SOT-223 3 OI SOIC (W) 28
EB DDPAK 3 OR SOIC (N) 16
EK DDPAK 7 PA PDIP (N) 8
ET DDPAK 5 PD PDIP (N) 14
HA SOP 8 PE PDIP (N) 16
JA CDIP (N) 8 PF PDIP (N) 24
JD CDIP (N) 14 PG PDIP (W) 24
JE CDIP (N) 16 PI PDIP (W) 28
JG CDIP (W) 24 PJ PDIP (W) 28
JI CDIP (W) 28 PL PDIP (W) 40
JL CDIP (W) 40 QR QSOP (N) 16
KU MQFP 64 RC SOT-143 4
KW MQFP 44 SI SSOP (W) 28
LB SC-70 3 UA MSOP 8
LI PLCC 28 UN MSOP 10
LS PLCC 68 VB DPAK 3
LT SC-70 5 ZB TO-92 3
LW PLCC 44 ZM TO-92 2
Taping Direction:
TR or 713: Standard Taping, blank: no tape and reel
Number of Package Pins (See specific data sheet)
Package Type
Operating Temperature Range:
C: Commercial Range (0°C to +70°C)
E: Extended Industrial Range (-40°C to +85°C)
I: Industrial Range (-25°C to +85°C)
M: Military Range (-55°C to +125°C)
V: See Data Sheet for Specific Temperature Range
(Extra Feature Code and/or Tolerance)* (See specific data sheet)
(Output Voltage or Detect Voltage)* (If applicable, see specific data sheet)
Electrical Performance Grade Option (Variation/Option)*
(If applicable, see specific data sheet)
A: Test Selection Criteria (See specific data sheet)
B:
R: Reversed Pin Layout
Product Part Number (2 to 6 characters, see specific data sheet)
Product Prefix
NOTE: ( )* Used for voltage regulators and detectors.
Analog and Interface Product Selector Guide 33
ANALOG PRODUCT PART NUMBERS
Package Type (see table below)
Operating Temperature Range:
- blank: Commercial Range (0°C to +70°C)
I: Industrial (-40°C to +85°C)
E: Extended Industrial Range (-40°C to +125°C
Supervisor Bond Options:
D:
F:
H:
blank: Not Applicable
Reset Voltage Thresholds or Performance Grade Options:
(1-3 characters, see specific data sheets)
270: 2.7V reset threshold
300: 3.0V reset threshold
315: 3.15V reset threshold
450: 4.5V reset threshold
460: 4.6V reset threshold
475: 4.7V reset threshold
485: 4.85V reset threshold
or
B: Grade (see specific data sheet)
C: Grade (see specific data sheet)
or
blank: not applicable
Tape and Reel:
T: Tape and Reel
blank: No Tape and Reel
Product Part Number (3-6 characters, see specific data sheet)
Product Prefix
Package Description # of Pins Tube/Bag Qty. Reel Qty.
TO TO-92 3 1000 n/a
TT SOT-23 3 n/a 3000
OT SOT-23 5 n/a 3000
P PDIP 8 60 n/a
SN SOIC 8 100 3300
ST TSSOP 8 100 2500
MS MSOP 8 100 2500
MF DFN (2x3) 8 n/a 3300
MF DFN (3x3) 8 50 3300
MF DFN (3x3, 10-Pin) 10 120 3300
ST TSSOP 14 96 2500
P PDIP 14 30 n/a
SL SOIC 14 57 2600
P PDIP 18 25 n/a
SO SOIC 18 42 1100
ST TSSOP 20 74 2500
SS SSOP 20 67 1600
ML QFN (6x6) 28 50 1600
ML QFN (4x4) 16 91 3300
Part Number Suffix Designations
Ordering Information for all Microchip Analog Products beginning with “MCP” prefix
MCP xxxxx T - yyy z h / qq
34 Analog and Interface Product Selector Guide
Analog and Interface Product Selector Guide 35
ANALOG PRODUCT PART NUMBERS
Tape and Reel:
TF: Tape and Reel
F: No Tape and Reel
Package Type (2 to 4 characters, see table below)
Product Part Number (3 characters, see specific data sheet)
Product Prefix
Package Description # of Pins Tube Qty. Reel Qty.
E8 PDIP 8 60 n/a
S8 SOIC 8 100 3300
E14 PDIP 14 30 n/a
S14 SOIC 14 57 2600
E16 PDIP 16 30 n/a
S16 SOIC 16 50 2600
SW16 SOIC (300 mil) 16 47 1000
Part Number Suffix Designations
Ordering Information for all Microchip Analog Products beginning with “RE46C” prefix
RE46C xxx yyyy zz
