A Global Leader in the Design, Development, and
Manufacture of Sensor and Magnetic Components
Series Datasheet – DIL Reed Relays www.standexmeder.com
DIL Series
Reed Relays
Features Compatible with 14 pin DIL socket, High resistance coil up to 11 kOhm available
Available with Dielectric Strength 4.25kVDC, Diode, Magnetic Shield & Others
Markets: General purposes, Telecommunications, Test and Measurement & Others
Part
Description: D I L 00- 0 X 00-00X
Nominal
Voltage
Contact
QTY
Contact
Form
Switch
Model Pin Out Option
() Version with Magnetic Shield
05, 12, 24 1, 2, 4 A, C 66, 75, 88, 90
13, 15, 21, 51,
62, 63 L(M), D(Q), E(R), F(S)
Customer
Options Switch Model Unit
Contact Data
66 75 88 90
Rated Power
(max.)
Any
DC combination of V&A not to exceed their individual max.’s 10 10 50 10 W
Switching Voltage
(max.)
DC or
peak AC 200 500 500 175 V
Switching Current
(max.)
DC
or peak AC 0.5 0.5 2 0.5 A
Carry Current
(max.)
DC
or peak AC 1.0 1.0 2 1.0 A
Contact Resistance
(max.)
@
0.5V & 50mA 150 200 80 150 mOhm
Breakdown
Voltage (min.)
According
to EN60255-5 0.225 1.5 1.5 0.2 kVDC
Operating
Time (max.)
Incl. Bounce; Measured with w/ Nominal Voltage
0.5 0.5 1.2 0.7 ms
Release Time (max.)
Measured
with no Coil Excitation 0.1 0.1 1.0 1.5 ms
Insulation
Resistance (typ.)
Rh<45
%, 100V Test Voltage 1010 1010 1011 109 GOhm
Capacitance
(typ.)
@
10kHz across open Switch 0.2 0.4 0.3 1.0 pF
Modifications in the sense of technical progress are reserved.
Version 01
27.01.2015
USA: +1.866.782.6339 │ salesusa@standexmeder.com
Europe: +49.7731.8399.0 │ info@standexmeder.com
Asia: +86.21.37820625 │ salesasia@standexmeder.com
A Global Leader in the Design, Development, and
Manufacture of Sensor and Magnetic Components
Series Datasheet – DIL Reed Relays www.standexmeder.com
Coil
Data Coil Voltage
(nom.)
Coil Resistance
(typ.)
Pull-In Voltage
(max.)
Drop-Out Voltage
(min.)
Nominal
Coil
Power
(typ.)
Contact
Form
Switch
Model
Unit VDC Ohm VDC VDC mW
1A
66, 72,
75, 88
05 450 3.5 0.75 55
12 1,800 8.4 1.8 80
24 4,500 16.8 3.6 130
2A
66, 72,
75, 88
05 200 3.5 0.75 125
12 680 8.4 1.8 210
24 2,000 16.8 3.6 290
4A 66
05 140 3.5 0.75 179
12 400 8.4 1.8 360
24 1,900 16.8 3.6 303
1C 90
05 200 3.5 0.75 125
12 1,000 8.4 1.8 145
24 3,000 16.8 3.6 190
2C 90
05 150 3.5 0.75 165
12 680 8.4 1.8 210
24 2,000 16.8 3.6 290
The Pull
-In / Drop-Out Voltage and Coil Resistance will change at Rate of 0.4% per °C
DIL Reed Relay
Environmental
Data Unit
Shock Resistance (max.)
1/2 sine wave duration 11ms
50 g
Vibration
Resistance (max.) 20 g
Operating Temperature
-20 to 70 °C
Storage Temperature
-25 to 85 °C
Soldering
Temperature (max.)
5 sec. max.
260 °C
Life Test Data
*Load increase reduces life
expectancy of Reed Switches
Handling
& Assembly Instructions
Switching inductive and/or capacitive loads create voltage
and/or current peaks, which may damage the relay.
Protective circuits need to be used.
External magnetic fields needs to be taken into
consideration, including a too high packing density. This may
influence the relays’ electrical characteristics.
Mechanical shock impacts e.g. dropping the relays may cause
immediate or post-installation failure.
Wave soldering: maximum 260°/5 seconds.
Reflow soldering: Recommendations given by the soldering
paste manufacturer need to be considered as well as the
temperature limits of other components/processes.
Modifications in the sense of technical progress are reserved.
Version 01
27.01.2015
USA: +1.866.782.6339 │ salesusa@standexmeder.com
Europe: +49.7731.8399.0 │ info@standexmeder.com
Asia: +86.21.37820625 │ salesasia@standexmeder.com
A Global Leader in the Design, Development, and
Manufacture of Sensor and Magnetic Components
Series Datasheet – DIL Reed Relays www.standexmeder.com
Pin Out
Glossary
Contact Form
Form
A
NO = Normally Open Contacts
SPST = Single Pole Single
Throw
Form B
NC = Normally Closed
Contacts
SPST
= Single Pole Single Throw
Form C
Changeover
SPDT = Single Pole Double
Throw
Options
Top View
2.54mm [0.10“] pitch grid
Top View
2.54mm [0.10“] pitch grid
Please Note: Any option can affect the coil resistance, the breakdown voltage or other electronical data. Please contact us.
Special performance: The following special options are available on request:
Other pinning layout
Other coil resistance values
Other switches available
Modifications in the sense of technical progress are reserved.
Version 01
27.01.2015
USA: +1.866.782.6339 │ salesusa@standexmeder.com
Europe: +49.7731.8399.0 │ info@standexmeder.com
Asia: +86.21.37820625 │ salesasia@standexmeder.com
