1
FEATURES
110
2
9
3
8
4
7
VCC
S
D+
D–
OE
1D+
1D–
2D+
2D–
GND
56
APPLICATIONS
DESCRIPTION
1
10
2
9
3
8
4
7
VCC
S
D+
D–
OE
1D+
1D–
2D+
2D–
GND
5
6
TS3USB221A
www.ti.com
.......................................................................................................................................................................................... SCDS277 NOVEMBER 2008
ESD PROTECTED, HIGH-SPEED USB 2.0 (480-Mbps)1:2 MULTIPLEXER/DEMULTIPLEXER SWITCH WITH SINGLE ENABLE
RSE PACKAGEV
CC
Operation at 2.5 V to 3.3 V
(TOP VIEW)V
I/O
Accepts Signals Up to 5.5 V1.8-V Compatible Control-Pin InputsLow-Power Mode When OE Is Disabled (1 µA)r
ON
= 6 MaximumΔr
ON
= 0.2 TypicalC
io(on)
= 6 pF TypicalLow Power Consumption (30 µA Maximum)High Bandwidth (900 MHz Typical)Latch-Up Performance Exceeds 100 mAPer JESD 78, Class IIESD Performance Tested Per JESD 22
RSE PACKAGE 7000-V Human-Body Model
(BOTTOM VIEW)(A114-B, Class II) 1000-V Charged-Device Model (C101)ESD Performance I/O to GND 12-kV Human-Body Model
Routes Signals for USB 1.0, 1.1, and 2.0
The TS3USB221A is a high-bandwidth switchspecially designed for the switching of high-speedUSB 2.0 signals in handset and consumerapplications, such as cell phones, digital cameras,and notebooks with hubs or controllers with limitedUSB I/Os. The wide bandwidth (900 MHz) of thisswitch allows signals to pass with minimum edge andphase distortion. The device multiplexes differentialoutputs from a USB host device to one of twocorresponding outputs. The switch is bidirectional andoffers little or no attenuation of the high-speed signalsat the outputs. It is designed for low bit-to-bit skewand high channel-to-channel noise isolation, and iscompatible with various standards, such ashigh-speed USB 2.0 (480 Mbps).
The TS3USB221A integrates ESD protection cells onall pins, is available in a tiny µQFN package (2.0 mm× 1.5 mm) and is charaterized over the free airtemperature range from 40 ° C to 85 ° C.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of TexasInstruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2008, Texas Instruments IncorporatedProducts conform to specifications per the terms of the TexasInstruments standard warranty. Production processing does notnecessarily include testing of all parameters.
BLOCK DIAGRAM
D−
D+
1D−
1D+
2D−
2D+
S
OE
A
EN (see Note A)
B
Charge
Pump
VCC
TS3USB221A
SCDS277 NOVEMBER 2008 ..........................................................................................................................................................................................
www.ti.com
ORDERING INFORMATION
T
A
PACKAGE
(1) (2)
ORDERABLE PART NUMBER TOP-SIDE MARKING
40 ° C to 85 ° C QFN RSE Reel of 3000 TS3USB221ARSER LHR
(1) Package drawings, thermal data, and symbolization are available at www.ti.com/packaging .(2) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TIwebsite at www.ti.com .
PIN DESCRIPTION
NAME DESCRIPTION
OE Bus-switch enableS Select inputD Bus AnD Bus B
TRUTH TABLE
S OE FUNCTION
X H DisconnectL L D = 1DH L D = 2D
SIMPLIFIED SCHEMATIC, EACH FET SWITCH (SW)
A. EN is the internal enable signal applied to the switch.
2Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TS3USB221A
ABSOLUTE MAXIMUM RATINGS
(1)
PACKAGE THERMAL IMPEDANCE
RECOMMENDED OPERATING CONDITIONS
TS3USB221A
www.ti.com
.......................................................................................................................................................................................... SCDS277 NOVEMBER 2008
over operating free-air temperature range (unless otherwise noted)
MIN MAX UNIT
V
CC
Supply voltage range 0.5 4.6 VV
IN
Control input voltage range
(2) (3)
0.5 7 VV
I/O
Switch I/O voltage range
(2) (3) (4)
0.5 7 VI
IK
Control input clamp current V
IN
< 0 50 mAI
I/OK
I/O port clamp current V
I/O
< 0 50 mAI
I/O
ON-state switch current
(5)
± 120 mAContinuous current through V
CC
or GND ± 100 mAT
stg
Storage temperature range 65 150 ° C
(1) Stresses beyond those listed under " absolute maximum ratings " may cause permanent damage to the device. These are stress ratingsonly, and functional operation of the device at these or any other conditions beyond those indicated under " recommended operatingconditions " is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.(2) All voltages are with respect to ground, unless otherwise specified.(3) The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed.(4) V
I
and V
O
are used to denote specific conditions for V
I/O
.(5) I
I
and I
O
are used to denote specific conditions for I
I/O
.
over operating free-air temperature range (unless otherwise noted)
UNIT
θ
JA
Package thermal impedance
(1)
RSE package 243 ° C/W
(1) The package thermal impedance is calculated in accordance with JESD 51-7.
MIN MAX UNIT
V
CC
Supply voltage 2.3 3.6 VV
CC
= 2.3 V to 2.7 V 0.46 × V
CCV
IH
High-level control input voltage VV
CC
= 2.7 V to 3.6 V 0.46 × V
CC
V
CC
= 2.3 V to 2.7 V 0.25 × V
CCV
IL
Low-level control input voltage VV
CC
= 2.7 V to 3.6 V 0.25 × V
CC
V
I/O
Data input/output voltage 0 5.5 VT
A
Operating free-air temperature 40 85 ° C
Copyright © 2008, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Link(s): TS3USB221A
ELECTRICAL CHARACTERISTICS
(1)
DYNAMIC ELECTRICAL CHARACTERISTICS
TS3USB221A
SCDS277 NOVEMBER 2008 ..........................................................................................................................................................................................
www.ti.com
over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP
(2)
MAX UNIT
V
IK
V
CC
= 3.6 V, 2.7 V, I
I
= 18 mA 1.8 VControlI
IN
V
CC
= 3.6 V, 2.7 V, 0 V, V
IN
= 0 V to 3.6 V ± 1 µAinputs
V
CC
= 3.6 V, 2.7 V, V
IN
= V
CC
or GND,I
OZ
(3)
± 1 µAV
O
= 0 V to 5.25 V, V
I
= 0 V, Switch OFFV
I/O
= 0 V to 5.25 V ± 2I
(OFF)
V
CC
= 0 V V
I/O
= 0 V to 3.6 V ± 2 µAV
I/O
= 0 V to 2.7 V ± 1V
CC
= 3.6 V, 2.7 V, I
I/O
= 0 V,I
CC
30 µAV
IN
= V
CC
or GND, Switch ON or OFFI
CC
V
CC
= 3.6 V, 2.7 V, Switch disabled,(low power 1 µAV
IN
= V
CC
or GND, OE in high statemode)
V
CC
= 3.6 V 20Control One input at 1.8 V,ΔI
CC
(4)
µAinputs Other inputs at V
CC
or GND
V
CC
= 2.7 V 0.5ControlC
in
V
CC
= 3.3 V, 2.5 V, V
IN
= V
CC
or 0 V 1.5 2.5 pFinputsC
io(OFF)
V
CC
= 3.3 V, 2.5 V, V
I/O
= V
CC
or 0 V, Switch OFF 3.5 5 pFC
io(ON)
V
CC
= 3.3 V, 2.5 V, V
I/O
= V
CC
or 0 V, Switch ON 6 7.5 pFV
I
= 0 V, I
O
= 30 mA 3 6r
ON
(5)
V
CC
= 3 V, 2.3 V V
I
= 2.4 V, I
O
= 15 mA 3.4 6V
I
= 0 V, I
O
= 30 mA 0.2Δr
ON
V
CC
= 3 V, 2.3 V V
I
= 1.7, I
O
= 15 mA 0.2V
I
= 0 V, I
O
= 30 mA 1r
ON(flat)
V
CC
= 3 V, 2.3 V V
I
= 1.7, I
O
= 15 mA 1
(1) V
IN
and I
IN
refer to control inputs. V
I
, V
O
, I
I
, and I
O
refer to data pins.(2) All typical values are at V
CC
= 3.3 V (unless otherwise noted), T
A
= 25 ° C.(3) For I/O ports, the parameter I
OZ
includes the input leakage current.(4) This is the increase in supply current for each input that is at the specified TTL voltage level, rather than V
CC
or GND.(5) Measured by the voltage drop between the A and B terminals at the indicated current through the switch. ON-state resistance isdetermined by the lower of the voltages of the two (A or B) terminals.
over operating range, T
A
= 40 ° C to 85 ° C, V
CC
= 3.3 V ± 10%, GND = 0 V
PARAMETER TEST CONDITIONS TYP UNIT
X
TALK
Crosstalk R
L
= 50 , f = 250 MHz 40 dBO
IRR
OFF isolation R
L
= 50 , f = 250 MHz 41 dBBW Bandwidth ( 3 dB) R
L
= 50 0.9 GHz
4Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TS3USB221A
DYNAMIC ELECTRICAL CHARACTERISTICS
SWITCHING CHARACTERISTICS
SWITCHING CHARACTERISTICS
TS3USB221A
www.ti.com
.......................................................................................................................................................................................... SCDS277 NOVEMBER 2008
over operating range, T
A
= 40 ° C to 85 ° C, V
CC
= 2.5 V ± 10%, GND = 0 V
PARAMETER TEST CONDITIONS TYP UNIT
X
TALK
Crosstalk R
L
= 50 , f = 250 MHz -39 dBO
IRR
OFF isolation R
L
= 50 , f = 250 MHz -40 dBBW Bandwidth (3 dB) R
L
= 50 0.9 GHz
over operating range, T
A
= 40 ° C to 85 ° C, V
CC
= 3.3 V ± 10%, GND = 0 V
PARAMETER MIN TYP
(1)
MAX UNIT
t
pd
Propagation delay
(2) (3)
0.25 nsS to D, nD 30t
ON
Line enable time nsOE to D, nD 17S to D, nD 12t
OFF
Line disable time nsOE to D, nD 10t
SK(O)
Output skew between center port to any other port
(2)
0.1 0.2 nst
SK(P)
Skew between opposite transitions of the same output (t
PHL
t
PLH
)
(2)
0.1 0.2 ns
(1) For Max or Min conditions, use the appropriate value specified under Electrical Characteristics for the applicable device type.(2) Specified by design(3) The bus switch contributes no propagational delay other than the RC delay of the on resistance of the switch and the load capacitance.The time constant for the switch alone is of the order of 0.25 ns for 10-pF load. Since this time constant is much smaller than the rise/falltimes of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch, when used ina system, is determined by the driving circuit on the driving side of the switch and its interactions with the load on the driven side.
over operating range, T
A
= 40 ° C to 85 ° C, V
CC
= 2.5 V ± 10%, GND = 0 V
PARAMETER MIN TYP
(1)
MAX UNIT
t
pd
Propagation delay
(2) (3)
0.25 nsS to D, nD 50t
ON
Line enable time nsOE to D, nD 32S to D, nD 23t
OFF
Line disable time nsOE to D, nD 12t
SK(O)
Output skew between center port to any other port
(2)
0.1 0.2 nst
SK(P)
Skew between opposite transitions of the same output (t
PHL
t
PLH
)
(2)
0.1 0.2 ns
(1) For Max or Min conditions, use the appropriate value specified under Electrical Characteristics for the applicable device type.(2) Specified by design(3) The bus switch contributes no propagational delay other than the RC delay of the on resistance of the switch and the load capacitance.The time constant for the switch alone is of the order of 0.25 ns for 10-pF load. Since this time constant is much smaller than the rise/falltimes of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch, when used ina system, is determined by the driving circuit on the driving side of the switch and its interactions with the load on the driven side.
Copyright © 2008, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Link(s): TS3USB221A
APPLICATION INFORMATION
100.0E+3 1.0E+6 10.0E+6 100.0E+6 1.0E+9 10.0E+9
Frequency (Hz)
–120
–100
–80
–60
–40
–20
0
Attenuation (dB)
100.0E+3 1.0E+6 10.0E+6 100.0E+6 1.0E+9 10.0E+9
Frequency (Hz)
–7
–6
–5
–4
–3
–2
–1
0
Gain (dB)
–120
–100
–80
–60
–40
–20
0
100.0E+3 1.0E+6 10.0E+6 100.0E+6 1.0E+9 10.0E+9
Frequency (Hz)
Attenuation (dB)
2.8
2.9
3.0
3.1
3.2
3.3
3.4
3.5
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5
V (V)
IN
r ( )
on Ω
V = 3 V
CC
V = 2.3 V
CC
TS3USB221A
SCDS277 NOVEMBER 2008 ..........................................................................................................................................................................................
www.ti.com
Figure 1. Gain vs Frequency Figure 2. OFF Isolation vs Frequency
Figure 3. Crosstalk vs Frequency Figure 4. r
on
vs V
IN
(I
OUT
= 15 mA)
Figure 5. r
ON
vs V
IN
(I
OUT
= 30 mA)
6Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TS3USB221A
Time ( 10 ) (s)X–9
Differential Signal (V)
0.0
–0.5
0.5
–0.4
0.4
–0.3
0.3
–0.2
0.2
–0.1
0.1
0.0
0.2 0.4 0.5 0.8 1.0 1.2 1.4 1.6 1.8 2.0
Time ( 10 ) (s)X–9
Differential Signal (V)
0.0
–0.5
0.5
–0.4
0.4
–0.3
0.3
–0.2
0.2
–0.1
0.1
0.0
0.2 0.4 0.5 0.8 1.0 1.2 1.4 1.6 1.8 2.0
Time ( 10 ) (s)X–9
Differential Signal (V)
0.0
–0.5
0.5
–0.4
0.4
–0.3
0.3
–0.2
0.2
–0.1
0.1
0.0
0.2 0.4 0.5 0.8 1.0 1.2 1.4 1.6 1.8 2.0
TS3USB221A
www.ti.com
.......................................................................................................................................................................................... SCDS277 NOVEMBER 2008
Figure 6. Eye Pattern: 480-Mbps USB Signal With No Figure 7. Eye Pattern: 480-Mbps USB Signal With SwitchSwitch (Through Path) NC Path
Figure 8. Eye Pattern: 480-Mbps USB Signal With SwitchNO Path
Copyright © 2008, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Link(s): TS3USB221A
PARAMETER MEASUREMENT INFORMATION
CL(2) RL
VIN
VCC
GND
1D or 2D VOUT1 or VOUT2
VCTRL
1D or 2D
D
Logic
Input(1)
V+
VCOM
500
RLCL
50 pFtON
TEST
V+
500 50 pFtOFF
50%
tON tOFF
50%
90% 90%
Logic
Input
(VI)
1.8 V
Switch
Output
(VOUT1 or VOUT2)
0
CL(2) RL
S
(1) All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr < 5 ns, tf < 5 ns.
(2) CL includes probe and jig capacitance.
VOH
VOL
1D
2D D
VOUT1
VIN
Channel OFF: 1D to D
Network Analyzer Setup
Source Power = 0 dBm
(632-mV P-P at 50-W load)
DC Bias = 350 mV
50 W
VCC
GND
50 W
50 W
Network Analyzer
Source
Signal
VCTRL
+
VCTRL = VCC or GND
S
TS3USB221A
SCDS277 NOVEMBER 2008 ..........................................................................................................................................................................................
www.ti.com
Figure 9. Turn-On (t
ON
) and Turn-Off Time (t
OFF
)
Figure 10. OFF Isolation (O
ISO
)
8Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TS3USB221A
1D
2D
50 W
50 W
VOUT1 VIN
Channel ON: 1D to D
Network Analyzer Setup
Source Power = 0 dBm
(632-mV P-P at 50-W load)
DC Bias = 350 mV
50 W
VCC
GND
VOUT2
Source
Signal
Channel OFF: 2D to D
Network Analyzer
VCTRL
+
VCTRL = VCC or GND
S
VCC
GND
1D
VCTRL
2D
D
50 W
50 W
VOUT1
VIN
Channel ON: 1D to D
Network Analyzer Setup
Source Power = 0 dBm
(632-mV P-P at 50-W load)
DC Bias = 350 mV
Network Analyzer
Source
Signal
+
VCTRL = VCC or GND
S
400 mV
TS3USB221A
www.ti.com
.......................................................................................................................................................................................... SCDS277 NOVEMBER 2008
PARAMETER MEASUREMENT INFORMATION (continued)
Figure 11. Crosstalk (X
TALK
)
Figure 12. Bandwidth (BW)
Figure 13. Propagation Delay
Copyright © 2008, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Link(s): TS3USB221A
800mV
800mV
400mV
400mV
50% 50%
50%
50%
50%
50%50%
50%
50%
OUTPUTSKEWtSK(P)
PULSESKEWtSK(P)
t = t t
SK(P) PHL PLH
| |
t = t t
SK(O) PLH1 PLH2
| | or | |t t
PHL1 PHL2
Input
Input
Output
Output2
Output1
VOL
VOL
VOL
VOH
VOH
VOH
tPLH
tSK(O) tSK(O)
tPHL2
tPLH2
tPLH1 tPHL1
tPHL
VCC
IIN
ron +VIN *VOUT2 or VOUT1
IIN
W
GND
Channel ON
1D
VCTRL
2D
DVIN
VCTRL = VIH or VIL
VOUT2
VOUT1
+
+S
TS3USB221A
SCDS277 NOVEMBER 2008 ..........................................................................................................................................................................................
www.ti.com
PARAMETER MEASUREMENT INFORMATION (continued)
Figure 14. Skew Test
Figure 15. ON-State Resistance (r
on
)
10 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TS3USB221A
Channel OFF
OFF-State Leakage Current
VCTRL = VIH or VIL
VCC
GND
1D
VCTRL
2D DVIN
VOUT2
VOUT1
+
+
+
S
VCC
GND
VBIAS VCTRL
VCTRL = VCC or GND
VBIAS = VCC or GND
Capacitance is measured at 1D,
2D, D, and S inputs during ON
and OFF conditions.
Capacitance
Meter
VIN
VOUT2
VOUT1
D
2D
1D
S
TS3USB221A
www.ti.com
.......................................................................................................................................................................................... SCDS277 NOVEMBER 2008
PARAMETER MEASUREMENT INFORMATION (continued)
Figure 16. OFF-State Leakage Current
Figure 17. Capacitance
Copyright © 2008, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Link(s): TS3USB221A
PACKAGE OPTION ADDENDUM
www.ti.com 9-Nov-2013
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
HPA02204RSER ACTIVE UQFN RSE 10 3000 Green (RoHS
& no Sb/Br) CU NIPDAUAG Level-1-260C-UNLIM -40 to 85 (LH7 ~ LHR)
TS3USB221ARSER ACTIVE UQFN RSE 10 3000 Green (RoHS
& no Sb/Br) CU NIPDAU |
CU NIPDAUAG Level-1-260C-UNLIM -40 to 85 (LH7 ~ LHR)
TS3USB221ARSERG4 ACTIVE UQFN RSE 10 3000 Green (RoHS
& no Sb/Br) CU NIPDAUAG Level-1-260C-UNLIM -40 to 85 (LH7 ~ LHR)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
PACKAGE OPTION ADDENDUM
www.ti.com 9-Nov-2013
Addendum-Page 2
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TS3USB221A :
Automotive: TS3USB221A-Q1
NOTE: Qualified Version Definitions:
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
TS3USB221ARSER UQFN RSE 10 3000 180.0 8.4 1.68 2.13 0.76 4.0 8.0 Q1
TS3USB221ARSER UQFN RSE 10 3000 180.0 9.5 1.68 2.18 0.9 4.0 8.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 6-Nov-2012
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
TS3USB221ARSER UQFN RSE 10 3000 202.0 201.0 28.0
TS3USB221ARSER UQFN RSE 10 3000 180.0 180.0 30.0
PACKAGE MATERIALS INFORMATION
www.ti.com 6-Nov-2012
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated