New Product CN-0313 NR01 Series Process Sealed Rotaries Subminiature Rotaries with Positive, Distinctive Detent 2017-07-17 Series NR01 Subminiature Process Sealed Rotaries General Specifications Electrical Capacity (Resistive Load) Logic Level: 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section Other Ratings Contact Resistance: 100 milliohms maximum Insulation Resistance: 100 megohms minimum @ 500V DC Dielectric Strength:500V AC minimum for 1 minute minimum Mechanical Life: 30,000 cycles minimum Electrical Life: 10,000 cycles minimum Nominal Operating Torque: 0.02Nm (0.177 lb * in) Contact Timing: Nonshorting Indexing: 45 for 3-position, 4-position & 5-position Materials & Finishes Housing: Base: Rotor: Movable Contactor: Stationary Contacts: Terminals: Mounting Bracket: Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: Glass fiber reinforced polyester (PBT) Glass fiber reinforced polyamide Polyacetal Beryllium copper with gold plating Phosphor bronze with gold plating Phosphor bronze with gold plating Steel with tin plating -25C through +70C (-13F through +158F) 90 ~ 95% humidity for 96 hours @ 40C (104F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) PCB Processing Soldering: Wave Soldering Recommended: Preheat temperature 110C; Preheat time 40 seconds; Peak Temperature 270C; Peak Time 6 seconds; Thickness of PCB 1.6mm; 2 Cycles. Manual Soldering Recommended: Temperature 390C for 4 seconds, 2 cycles. Cleaning: Automated cleaning. See Cleaning Specifications in Supplement section. Standards & Certifications The NR01 Series rotaries have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. Note: Values are determined by NKK's individual specification tests in a controlled environment, and do not certify that the product supports simultaneous multiple conditions. 2 www.nkkswitches.com Series NR01 Subminiature Process Sealed Rotaries Distinctive Characteristics Totally sealed construction with internal o-ring, gasket between base and housing, and insert-molded terminals, gives protection for automated processing techniques. Detent mechanism, with its spring-operated steel ball, gives distinct feel and crisp actuation for accurate switch setting. Subminiature size and compact body contributes to high density mounting. Bifurcated, self-wiping contact mechanism provides unequalled logic-level reliability and smoother, positive detent actuation. Crimped bracket legs ensure secure PCB mounting and prevent dislodging during automated wave soldering. Molded-in terminals prevent entry of flux and other contaminants. .100" x .100" (2.54mm x 2.54mm) terminal spacing conforms to standard PC board grid spacing. Applications Actual Size * Power Control Equipment * Medical Equipment * Measuring Devices * Teaching Pendant * Telecommunication Equipment www.nkkswitches.com 3 Series NR01 Subminiature Process Sealed Rotaries TYPICAL SWITCH ORDERING EXAMPLE NR01 1 03 A N G Pole 1 C PC Terminals Single Pole 1 13 Contact Timing N 13 Contact Material Nonshorting G Circuits, Positions & Indexing Gold Rated 0.4VA @ 28V AC/DC ON ON ON -- -- 45 04 ON ON ON ON -- 45 05 ON ON ON ON ON 45 A Black C Red H Gray Knobs No Code Code Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 5 Index 03 Colors Straight with Bracket DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Without Knob 1 Knob Without Flange 2 Knob With Flange NR01103ANG13-1C Red Knob without Flange Gold Contacts with 0.4VA Rating SP3T ON-ON-ON Circuit Positions 1, 2 & 3 Straight PC Terminals with Bracket POLES & CIRCUITS Actuator Positions Pole Model Pos 1 Pos 2 Pos 3 Pos 4 Throw & Schematics Connected Terminals Pos 5 Pos 1 Pos 2 Pos 3 Pos 4 Pos 5 Note: Terminal numbers are not actually on switch C SP3T NR01103 ON ON ON -- -- C-2 C-3 C-4 -- -- 2 3 4 C SP4T NR01104 ON ON ON ON -- C-2 C-3 C-4 C-5 -- 2 3 4 5 C SP5T NR01105 ON ON ON ON ON C-1 C-2 C-3 C-4 C-5 1 CONTACT MATERIAL & RATING G 13 Gold over Bronze or Copper Logic Level 0.4VA @ 28V AC/DC maximum 4 TERMINALS www.nkkswitches.com Straight PC with Bracket 2 3 4 5 Series NR01 Subminiature Process Sealed Rotaries TYPICAL SWITCH DIMENSIONS 45 Indexing * SP3T * Straight PC POS 2 Part No. This Side 45 45 POS 1 POS 3 (10.7) .421 0.5) Typ .020 (0.6) Typ .024 2 3 (5.9) Dia .232 (9.0) Dia .354 (10.7) .421 (0.7) Typ .028 (0.3) Typ .012 (4.7) .185 (10.5) .413 (20.7) .815 Actuator shown in Position 1 (1.5) Typ .059 1 C 5 4 (2.54) Typ .100 (3.5) .138 (3.5) Typ .138 1 2 C 3 5 4 (2.54) Typ .100 (5.08) .200 (10.16) .400 (2.54) Typ .100 (1.0) Dia Typ .039 (5.08) .200 NR01103ANG13-1C Terminals 1 & 5 are support pins 45 Indexing * SP4T * Straight PC POS 2 POS 1 Part No. This Side 45 45 POS 3 (0.7) Typ .028 (0.3) Typ .012 0.5) Typ .020 (0.6) Typ .024 45 (10.7) .421 POS 4 2 3 (5.9) Dia .232 (9.0) Dia .354 (10.7) .421 (4.7) .185 (10.5) .413 (20.7) .815 Actuator shown in Position 1 (1.5) Typ .059 1 C 5 4 (2.54) Typ .100 (3.5) .138 (3.5) Typ .138 1 2 C 3 5 4 (2.54) Typ .100 (5.08) .200 (10.16) .400 (2.54) Typ .100 (1.0) Dia Typ .039 (5.08) .200 NR01104ANG13-2C Terminal 1 is a support pin 45 Indexing * SP5T * Straight PC POS 3 POS 2 45 Part No. This Side 45 POS 4 45 (0.7) Typ .028 (0.3) Typ .012 0.5) Typ .020 (0.6) Typ .024 45 (10.7) .421 POS 1 POS 5 2 3 (5.9) Dia .232 (9.0) Dia .354 (10.7) .421 (4.7) .185 (10.5) .413 (20.7) .815 (2.54) Typ .100 (3.5) .138 (3.5) Typ .138 (1.5) Typ .059 1 C 5 4 (2.54) Typ .100 (5.08) .200 (10.16) .400 1 2 C 3 5 4 (2.54) Typ .100 (1.0) Dia Typ .039 (5.08) .200 NR01105ANG13-2C Actuator shown in Position 1 KNOBS No Code Without Knob 1 AT3008 Without Flange Material: Glass fiber reinforced polyamide (7.0) .276 2 (12.0) .472 AT3009 With Flange Material: Glass fiber reinforced polyamide (10.8) .425 (9.5) .374 Knob Colors (12.0) .472 (16.0) .630 A Black C Red H Gray MOUNTING & INSTALLATION Knob Installation To prevent knob from disassembling from the switch, it is recommended to use the type with a flange. Mount the knob with the flange (AT3009, assembled to switch) beneath the panel, as shown in illustration. Panel www.nkkswitches.com Knob Flange PCB 5 Series NR01 Subminiature Process Sealed Rotaries Ideal for Applications that Require Small Sizes with Precision & Reliability Situation Need for Compact Rotary Switch Simple, Accurate Solution Functionality in Compact Body DIP Rotary Switch has Unsatisfactory Complex Functionality Tactile Response is Not Essential Distinctive Detent with Single Pole Contact Reliability 3 ~ 5 Positions Advantages * Simplified soldering and automated cleaning processes enhance production efficiency * Reinforced bracket with crimped legs improves mounting stability and strength * Easy, straightforward functionality * Small, subminiature size with precise detent and crisp actuation Typical Applications Input Switching F2 F1 F3 AC, DC, GND Switching Function F1, F2, F3, F4 Signal Mode Selection CH1, CH2, DUAL Handheld Automation Devices 6 Measuring Devices www.nkkswitches.com Series NR01 Subminiature Process Sealed Rotaries A Comprehensive Line of Rotary Switches Meets a Variety of Applications PCB Mount Rotaries NR01 MRB MRA112 FR01 1 1 1, 2, 4 -- Specifications Number of Poles Positions Electrical Capacity Electrical Life 3, 4, 5 2, 3 2 ~ 12 -- 0.4VA Max @ 28V AC/DC Max 0.4VA Max @ 28V AC/DC Max 250mA @ 125V AC 100mA @ 5V DC 10,000 Operations Min 10,000 Operations Min 10,000 Operations Min 10,000 Detent Operations Min Operating Temperature -25 ~ +70C (-13 ~ +158F) -10 ~ +70C (+14 ~ +158F) External Dimensions 10.7 x 10.7mm (.421 x .421") 14.5 x 15.74mm (.571 x .620") Process Sealed Yes Subminiature & Ultra-Miniature DIP Rotaries FR01 ND -10 ~ +70C (+14 ~ +158F) -25 ~ +85C (-13 ~ +185F) 16mm Dia (.630" Dia) 10.0 x 10.0mm (.394 x .394") Yes No Yes Miniature & Subminiature Rotaries NR01 * Process Sealed * Positive Detent * 0.4VA @ 28V AC/DC * Subminiature * 10mm Ultra-Thin * 100mA @ 5/50V DC * Subminiature * HS13 * 6A TS * Process Sealed * 100mA @ 5/50V DC * Ultra-Miniature ND3 MRX Detent Bushing & Housing * 1A @ 30V DC * Miniature * 6A @ 125/250V AC Bushing * 10mm * Positive * Metal HS16 * 12A Ultra-Thin @ 5/50V DC * Subminiature * * 100mA * 8mm * Process Sealed @ 5/50V DC * Ultra-Miniature * 100mA * Process Sealed * IP67 Rated * 0.4VA @ 28V AC/DC * Miniature @ 125V AC Bushing * 10mm MRB * 10mm @ 125V AC Bushing * 10mm * 8mm SMT DIP Rotaries FR02 Standard Rotaries with Multiple Positions & Poles PS * 30A @ 125/250V AC Bushing * 10mm NKK offers optional knobs for Rotary Switches. See Accessories or contact our Sales Department. Effective Date July 2017 http://www.nkkswitches.com * 1.877.2BUYNKK (228.9655) 7850 East Gelding Drive * Scottsdale, AZ 85260 * Telephone 480.991.0942 * Fax 480.998.1435 www.nkkswitches.com 7