VNQ7003SY Quad-channel high-side driver with 16-bit SPI interface for automotive applications Datasheet - production data - Undervoltage shutdown - Overvoltage clamp - Latch-off or programmable time limited auto restart (power limitation and overtemperature shutdown) - Load dump protected - Protection against loss of ground Features Channel Description VCC RON(typ) ILIMH(typ) 0-1 28 V 25 m 35 A 2-3 28 V 7 m 80 A AEC-Q100 qualified General - 16-bit ST-SPI for full diagnostic with 8 bits Short Frame option - Programmable Bulb/LED mode for ch. 0-1 - Advanced limp home functions for robust fail-safe system - Very low standby current - Optimized electromagnetic emissions - Very low electromagnetic susceptibility - Control through direct inputs and / or SPI - Compliant with European directive 2002/95/EC Diagnostic functions - Multiplex proportional load current sense - Synchronous diagnostic of over load and short to GND, output shorted to VCC and OFF-state open-load - Programmable case overtemperature warning Protection - Two levels load current limitation - Self limiting of fast thermal transients April 2018 This is information on a product in full production. The VNQ7003SY is a device made using STMicroelectronics(R) VIPower(R) technology. It is intended for driving resistive or inductive loads directly connected to ground. The device is protected against voltage transient on VCC pin. An 8 bit short frame access to output control registers is provided allowing PWM control through SPI with high granularity. An analog current feedback for each channel is connected to the CURRENT-SENSE pin via a multiplexer. The device detects open-load in OFFstate conditions. Real time diagnostic is available through the SPI bus (open-load, output short to VCC, overtemperature, communication error, power limitation or latch off). Output current limitation protects the device in an over load condition. The device can limit the dissipated power to a safe level up to thermal shutdown intervention. Thermal shutdown can be configured as latched off or programmable time limited auto restart. The device enters a limp home mode in case of loss of digital supply (VDD), reset of digital memory or watchdog monitoring time-out event. In this mode states of channel 0, 1, 2 or 3 are respectively controlled by four dedicated pins IN0, IN1, IN2 and IN3. Channel 0 and 1 can be programmed via SPI for load type (BULB/ LED mode). DocID027886 Rev 7 1/100 www.st.com Contents VNQ7003SY Contents 1 Block diagram and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2 Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 4 2.1 Device interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 2.2 Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Startup transition phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.2.2 Reset mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.2.3 Fail Safe mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.2.4 Normal mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 2.2.5 Standby mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2.2.6 Sleep mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.2.7 Sleep mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.2.8 Battery undervoltage mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.2.9 Limp Home mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Protections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3.1 Pre-warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3.2 Junction overtemperature (OT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3.3 Power limitation (PL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 SPI functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4.1 4.2 4.3 2/100 2.2.1 SPI communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4.1.1 Signal description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4.1.2 Connecting to the SPI bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 4.1.3 SPI mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 SPI protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 4.2.1 SDI format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 4.2.2 SDO format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 4.2.3 Operating code definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 4.2.4 Special commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 4.3.1 Global Status byte description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 4.3.2 RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 4.3.3 ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 DocID027886 Rev 7 VNQ7003SY Contents 4.3.4 SPI modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 4.4 Output switching slopes control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 4.5 Output control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 4.6 Control registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 4.6.1 Address 0x00h -- Control Register (CTLR) . . . . . . . . . . . . . . . . . . . . . 40 4.6.2 Address 0x01h -- Direct Input Enable Control Register (DIENCR) . . . 41 4.6.3 Address 0x02h -- Open-load OFF-State Control Register (OLOFFCR) 42 4.6.4 Address 0x03h -- Channel Control Register (CCR) . . . . . . . . . . . . . . . 42 4.6.5 Address 0x04h -- Fast Switching Configuration Register (FASTSWCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 5 4.6.6 Address 0x06h -- CurrentSense Multiplexer Control Register (CSMUXCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 4.6.7 Address 0x07h -- SPI Output Control Register (SOCR) . . . . . . . . . . . . 43 4.6.8 Address 0x08h -- Channel Latch OFF Timer Control Register (ch0, ch1) (CHLOFFTCR0,1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 4.6.9 Address 0x09h -- Channel Latch OFF Timer Control Register (ch2, ch3) (CHLOFFTCR2,3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 5.1 Analogue diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 5.2 Digital diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 5.2.1 6 Status registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 5.3 Over load (VDS high voltage, Over Load (OVL)) . . . . . . . . . . . . . . . . . . . 48 5.4 Open-load ON-state detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 5.5 Open-load OFF-state detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 5.6 Address 0x2Fh -- DIENSR: Direct Input Status register . . . . . . . . . . . . . 50 5.7 Address 0x30h -- Channel Feedback Status Register (CHFBSR) . . . . . 51 5.8 Address 0x31h -- Open-load OFF-State / Stuck to VCC Status Register (OLOFFCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 5.9 Address 0x32h -- Channels latch-off status register (CHLOFFSR) . . . . 52 5.10 Address 0x33h -- VDS Feedback Status Register (VDSFSR) . . . . . . . . 52 5.11 Address 0x34h -- Generic Status Register (GENSR) . . . . . . . . . . . . . . . 53 5.12 Address 0x3Fh -- Configuration Register (CONFIG) . . . . . . . . . . . . . . . 53 Programmable blanking window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 6.1 Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 DocID027886 Rev 7 3/100 4 Contents 7 VNQ7003SY 6.2 Blanking window values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 6.3 Limp Home mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 6.4 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 7.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 7.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 7.3 SPI electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 7.4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 7.4.1 BULB mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 7.4.2 LED mode (Channel 0, 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 8 ISO Pulse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 9 Application schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 10 Package and PCB thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 10.1 PowerSSO-36 thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 11 Maximum demagnetization energy (VCC = 16 V) . . . . . . . . . . . . . . . . . 85 12 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 12.1 PowerSSO-36 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 12.2 PowerSSO-36 packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 12.3 PowerSSO-36 marking information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 13 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 14 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 4/100 DocID027886 Rev 7 VNQ7003SY List of tables List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. Table 27. Table 28. Table 29. Table 30. Table 31. Table 32. Table 33. Table 34. Table 35. Table 36. Table 37. Table 38. Table 39. Table 40. Table 41. Table 42. Table 43. Table 44. Table 45. Table 46. Table 47. Table 48. Pin functionality description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Frame 1: write CTRL 0x00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Frame 1: read (ROM) 0x3FH 0x--. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Frame 1: write CTRL 0x10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Frame 2: write CTRL 0x01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Frame 1: write CTRL 0x10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Frame 2: write CTRL 0x20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Frame 2: write CTRL 0x11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Frame 2: write CTRL 0x20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 SPI signal description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Command byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Input data byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Global status byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Output data byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Operating codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 0xFF: SW_Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Clear all status registers (RAM access) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Global status byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 RAM memory map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 ROM memory map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 SPI Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 SPI Burst Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 SPI Data Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 SPI 8 bit Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 SPI Data Consistency Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Switching slopes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Write SOCR 0x06 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Write SOCR Dummy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Truth table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 CTLR -- Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 DIENCR -- Direct Input Enable Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 OLOFFCR -- Open-load OFF-state control register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 CCR -- Channel control register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 FASTSWCR -- Fast Switching Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 CSMUXCR -- CurrentSense Multiplexer Control Register. . . . . . . . . . . . . . . . . . . . . . . . . 43 Truth table for CurrentSense Mux Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 SOCR -- SPI Output Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Channel configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 CHLOFFTCR0,1 -- Channel Latch OFF Timer Control Register (ch0, ch1) . . . . . . . . . . . 44 CHLOFFTCR2,3 -- Channel Latch OFF Timer Control Register (ch2, ch3) . . . . . . . . . . . 44 Status registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 STKFLTR state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 DIENSR -- Direct Input Status register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 CHFBSR -- Channel Feedback Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 STKFLTR -- Open-load OFF-State / Stuck to VCC Status Register . . . . . . . . . . . . . . . . . 51 CHLOFFSR -- Channels latch-off status register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 VDSFSR -- VDS Feedback Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 DocID027886 Rev 7 5/100 6 List of tables Table 49. Table 50. Table 51. Table 52. Table 53. Table 54. Table 55. Table 56. Table 57. Table 58. Table 59. Table 60. Table 61. Table 62. Table 63. Table 64. Table 65. Table 66. Table 67. Table 68. Table 69. Table 70. Table 71. Table 72. Table 73. Table 74. Table 75. Table 76. Table 77. Table 78. Table 79. Table 80. Table 81. Table 82. Table 83. Table 84. 6/100 VNQ7003SY GENSR -- Generic Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 CONFIG -- Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Time values written by MCU and their real value in timer register . . . . . . . . . . . . . . . . . . . 58 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 DC characteristics - Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 DC characteristics - Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 AC characteristics (SDI, SCK, CSN, SDO pins) - Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . 63 AC characteristics (SDI, SCK, CSN, SDO pins) - Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . 64 Dynamic characteristics - Mode 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Dynamic characteristics - Mode 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 VREG pin - Mode 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Power section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Logic inputs (IN0,1,2,3 pins) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Open-load detection (7V < VCC < 18 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 BULB - power section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 BULB - switching (VCC = 13 V; Normal switch mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 BULB - switching (VCC = 13 V; Fast switch mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 BULB - protection and diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 BULB - CurrentSense (7 V < VCC < 18 V, channel 0,1; Tj = -40 C to 150 C) . . . . . . . . . 70 BULB - CurrentSense (7 V < VCC < 18 V, channel 2,3; Tj = -40 C to 150 C) . . . . . . . . . 72 LED - power section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 LED - switching (VCC = 13 V; Normal switch mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 LED - switching (VCC = 13 V; Fast switch mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 LED - protection and diagnosis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 LED - CurrentSense (7 V < VCC < 18 V; Tj = -40 C to 150 C) . . . . . . . . . . . . . . . . . . . . 74 ISO 7637-2 - electrical transient conduction along supply line . . . . . . . . . . . . . . . . . . . . . . 77 Component values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 PCB properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Thermal parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 PowerSSO-36 mechanical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Reel dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 PowerSSO-36 carrier tape dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 DocID027886 Rev 7 VNQ7003SY List of figures List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Figure 25. Figure 26. Figure 27. Figure 28. Figure 29. Figure 30. Figure 31. Figure 32. Figure 33. Figure 34. Figure 35. Figure 36. Figure 37. Figure 38. Figure 39. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Connection diagram (top view--not to scale) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Battery undervoltage shutdown diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Undervoltage shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Device state diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Thermal shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Power limitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Supported SPI mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Bus master and two devices in a normal configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 SDI Frame 8 bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 SDO Frame 8 bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 SPI write operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 SPI read operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 SPI read and clear operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 SPI read device information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 VNQ7003SY: 4-channel direct input block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Diagnostic registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Open-load OFF-state detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Diagnostic flowchart based on GSB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Diagnostic flowchart for open-load off-state respectively stuck to VCC failure. . . . . . . . . . 55 Diagnostic flowchart for digital overload detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Internal timer process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 VNQ7003SY CHLOFFSR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 SPI dynamic characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 CurrentSense delay characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Switching characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 M0-7 SPI Standard connection SPI only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 M0-7 SPI standard, full connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 PowerSSO-36 PC board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Rthj-amb vs PCB copper area in open box free air conditions . . . . . . . . . . . . . . . . . . . . . . 81 PowerSSO-36 thermal impedance junction ambient single pulse . . . . . . . . . . . . . . . . . . . 82 Thermal fitting model for PowerSSO-36 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Maximum turn off current versus inductance - Channel 0,1 . . . . . . . . . . . . . . . . . . . . . . . . 85 Maximum turn off current versus inductance - Channel 2,3 . . . . . . . . . . . . . . . . . . . . . . . . 85 PowerSSO-36 package outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 PowerSSO-36 reel 13" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 PowerSSO-36 carrier tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 PowerSSO-36 schematic drawing of leader and trailer tape . . . . . . . . . . . . . . . . . . . . . . . 92 PowerSSO-36 marking information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 DocID027886 Rev 7 7/100 7 Block diagram and pin description 1 VNQ7003SY Block diagram and pin description Figure 1. Block diagram 8/100 DocID027886 Rev 7 VNQ7003SY Block diagram and pin description Figure 2. Connection diagram (top view--not to scale) Note: Pins 31,32,33,34,35 and 36 (OUTPUT3) must be connected together. Note: Pins 27,28,29 and 30 (OUTPUT0) must be connected together. Note: Pins 7,8,9 and 10 (OUTPUT1) must be connected together. Note: Pins 1,2,3,4,5 and 6 (OUTPUT2) must be connected together. Table 1. Pin functionality description Pin number Name Function -- VCC Battery connection. This is the backside TAB and is the direct connection to drain Power MOSFET switches. 19, 20 GND Ground connection. This pin serves as the ground connection for the logic part of the device. 13 GND Ground connection. This is a Kelvin ground connection for the logic part of the device and is used to connect an external EMC capacitor to the VREG pin. It must not be connected to application ground. 27, 28,29, 30 OUTPUT0 Power OUTPUT 0. It is the direct connection to the source Power MOSFET switch No. 0. 7, 8, 9, 10 OUTPUT1 Power OUTPUT 1. It is the direct connection to the source Power MOSFET switch No. 1. 1, 2, 3, 4,5, 6 OUTPUT2 Power OUTPUT 2. It is the direct connection to the source Power MOSFET switch No. 2. DocID027886 Rev 7 9/100 93 Block diagram and pin description VNQ7003SY Table 1. Pin functionality description (continued) Pin number Name 31,32,33, 34,35,36 OUTPUT3 Power OUTPUT 3. It is the direct connection to the source Power MOSFET switch No. 3. 15 CSN Chip select not (active low). It is the selection pin of the device. It is a CMOS compatible input. 16 SCK Serial clock. It is a CMOS compatible input. 17 SDI Serial data input. Transfers data to be written serially into the device on SCK rising edge. 18 SDO Serial data output. Transfers data serially out of the device on SCK falling edge. 14 VREG Output of the 3 V regulated internal supply for the digital control. Connect a low ESR capacitor close to this pin. 22 IN0 Direct Input pin for channel 0. Controls the OUTPUT 0 state in limp home mode, is ORed to SPI control register in normal operating mode when corresponding bit is set in DIENCR (Direct Input ENable) control register. 23 IN1 Direct Input pin for channel 1. Controls the OUTPUT 1 state in limp home mode, is ORed to SPI control register in normal operating mode when corresponding bit is set in DIENCR (Direct Input ENable) control register. 24 IN2 Direct Input pin for channel 2. Controls the OUTPUT 2 state in limp home mode, is ORed to SPI control register in normal operating mode when corresponding bit is set in DIENCR (Direct Input ENable) control register. 25 IN3 Direct Input pin for channel 3. Controls the OUTPUT 3 state in limp home mode, is ORed to SPI control register in normal operating mode when corresponding bit is set in DIENCR (Direct Input ENable) control register. 12 VDD External 5 V or 3.0 V supply. Powers the SPI interface. 21 CurrentSense 11, 26 NC 10/100 Function Analog CurrentSense generator proportional to output current. CurrentSense can be programmed as bulb/LED mode for each channel. The pin can deliver the CurrentSense of OUTPUT 0, 1, 2 or 3. The value of resistance that is connected between the CurrentSense pin and device ground determines the reading level for the microcontroller. Not connected DocID027886 Rev 7 VNQ7003SY Functional description 2 Functional description 2.1 Device interfaces SPI: bi-directional interface, accessing RAM/ROM registers (CSN, CLK, SDI, SDO) INx: input pins for outputs control while device is in Fail Safe mode, Standby mode or Reset mode (usable also in Normal mode according to "Direct Input Enable Control Register" - DIENCR setting) CSense: current-sense output used for analogue monitoring (monitored signal selection via RAM register) VDD: 5 V supply / 3 V option: VDD can be shared with microcontroller for 3 V or 5 V. This gives the range of the SPI for 3 V to 5 V. The VREG block is able to handle both the 3 V and 5 V. 2.2 Operating modes The device can operate in seven different modes: Reset mode Fail Safe mode Normal mode Standby mode Sleep mode 1 Sleep mode 2 Battery undervoltage mode The Reset mode, the Fail Safe mode and the Sleep mode 1 are combined into the Limp home mode. In this mode the chip is able to operate without the connection to the SPI. All transitions between the states in limp home mode are driven by VDD and INx. The outputs are controlled by the direct inputs INx. For an overview over the operating modes and the triggering conditions please refer to Table 10: Operating modes. 2.2.1 Startup transition phase This is not an operation mode but a transition step to Reset operation mode from the power-ON. In this phase, neither digital supply voltage VDD nor VCC are available (VDD < VDD_POR_ON and VCC < VUSD). This phase has not to be confused with Undervoltage mode where also the power supply is not available (VCC < VUSD) after an operation mode. The device leaves this phase to Reset mode as soon as VCC > VUSD. In case (VCC < VUSD) but (VDD > VDD_POR_ON) then the device leaves this phase to Fail-Safe-Mode. 2.2.2 Reset mode The device is in Limp Home state. Reset mode is entered after Startup but also each time the digital supply voltage VDD falls below VDD_POR_OFF (VDD < VDD_POR_OFF and VCC > VUSD). The outputs are controlled by the direct inputs INx. At least one INx is in logic High. The SPI is inactive (no read / write possible) and the diagnostics are not available. The registers have the Reset values. DocID027886 Rev 7 11/100 93 Functional description VNQ7003SY The device leaves this mode only if VDD > VDD_POR_ON or all INx go to low. The reset bit inside the Global Status Byte is set to 0 (for more information refer to the Global Status Byte register description). The diagnostics is not available, but the protections are fully functional. In case of overtemperature or power limitation, the outputs work in unlimited auto-restart. The device enters Reset mode under three conditions: Automatically during startup If it is in any other mode and if VDD falls below VDD_POR_OFF If it is in Sleep mode 1 and if only one input INx is set to 1 Reset mode can be left with 2 conditions: If VDD rises above VDD_POR_ON, the device enters Fail Safe mode If all inputs INx are 0, the device enters Sleep mode 1. 2.2.3 Fail Safe mode The device is in Limp Home state. The digital supply voltage VDD is available (VDD > VDD_POR_ON) and the SPI registers are active (SPI read/write). The device enters Fail Safe mode under five conditions: If it is in Reset mode or in Sleep mode 1 and VDD rises above VDD_POR_ON, (VDD > VDD_POR_ON) If it is in Standby mode or in Sleep mode 2 and CSN is low for t > tstdby_out If it is in Normal mode and bit EN is cleared If it is in Normal mode and WDTB is not toggled within tWDTB (watchdog timeout) If it is in Normal mode and the SPI sends a SW reset In case of Fail Safe mode, there is no analogue diagnostics (CurrentSense is inactive, not available) but the digital diagnosis is available through SPI bus. The outputs are controlled by the direct inputs INx regardless of SPI commands. The registers are cleared to their reset value if Fail Safe is entered through a SW reset. The reset bit is 1 if the last state was Reset mode or the last command was a SW reset and it is reset to 0 after the first valid SPI access (for more information refer Section 4.3.1: Global Status byte description). The SPI diagnostics is available. The protections are fully functional. In case of overtemperature or power limitation, the outputs work in unlimited auto-restart. The device exits Fail Safe mode under three conditions: If the SPI sends the goto Normal mode sequence, the device enters Normal mode: - In a first communication set bit UNLOCK = 1 - In the consecutive communication set bit STBY = 0 and bit EN = 1 This mechanism avoids entering the Normal mode unintentionally. If the SPI sends the goto standby mode sequence, the device enters Standby mode: - In a first communication set bit UNLOCK = 1 - In the consecutive communication set bit STBY = 1 and bit EN = 0 12/100 DocID027886 Rev 7 VNQ7003SY Functional description This mechanism avoids entering the Standby mode unintentionally. If VDD falls below VDD_POR_OFF, the device enters Reset mode. Transition to Fail-Safe-mode from Normal mode, using the SPI register Only one frame is needed. Table 2. Frame 1: write CTRL 0x00 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 x(1) x x EN(1) Command OC1 OC0 0 0 Address 0 0 Data x(1) GOSTBY x(1) UNLOCK X(2) 1. To avoid an SPI Error Frame due to a stuck at Zero, one bit of data field has to be at '1'. Bit "EN" has to be at `0' to force the device in Fail safe mode. 2. X: do not care. Transition to Fail-Safe-mode from Normal mode by SW-Reset SPI Reset is occurring by using the "Read device information" command (applicable only on ROM area) at reserved ROM address 0x3F. This is equivalent of sending a 0xFF command. Only one frame is needed. Table 3. Frame 1: read (ROM) 0x3FH 0x-Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 1 1 1 1 x x x x Command OC1 OC0 1 1 Address 1 1 (1) Data x x x x X(2) 1. The "X" data field cannot be all ones, otherwise a stuck to VDD is detected. 2. X: do not care. 2.2.4 Normal mode In this mode, all device functions are available. The transition to this mode is only possible from a previous Fail-Safe mode. Outputs can be driven by SPI commands or a combination of SPI command and direct inputs INx. To maintain the device in normal mode, the watchdog toggle bit in register CONFIG has to be toggled within the watchdog timeout period tWDTB (see Table 58: Dynamic characteristics - Mode 1or Table 59: Dynamic characteristics - Mode 2). DocID027886 Rev 7 13/100 93 Functional description VNQ7003SY Diagnosis is available through SPI bus (digital) and through CurrentSense pin (analogue CurrentSense). The protections are fully functional. The outputs can be set to latch-off or programmable time limited autorestart. In auto-restart the outputs are switched on again automatically after an overtemperature or power limitation event, while in latch the relevant status register has to be cleared to switch them on again. In time limited auto-restart the behavior is like auto-restart but within limited programmed time frame (refer to Section 6.2: Blanking window values). The device enters Normal mode under one condition: If it is in Fail Safe mode and the go to Normal mode sequence is sent through SPI: this mechanism avoids entering Normal mode unintentionally. - In a first communication set bit UNLOCK = 1 - In the consecutive communication set bit STBY = 0 and bit EN = 1 The transition from Fail-Safe-mode to Normal mode is performed by two special SPI sequences Table 4. Frame 1: write CTRL 0x10 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 Command OC1 OC0 0 0 Address 0 0 Data x x GOSTBY UNLOCK x x x EN 0 0 0 1 0 0 0 0 Bit 2 Bit 1 Bit 0 0 0 0 0 Table 5. Frame 2: write CTRL 0x01 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Command OC1 OC0 0 0 Address 0 0 Data x x GOSTBY UNLOCK x x x EN 0 0 0 0 0 0 0 1 14/100 DocID027886 Rev 7 VNQ7003SY Functional description Normal mode can be left with five conditions: If VDD falls below VDD_POR_OFF, the device enters Reset mode. If the SPI sends the goto standby sequence, the device enters Standby mode: this mechanism avoids entering Standby mode unintentionally. - In a first communication set UNLOCK = 1 - In the consecutive communication set STBY = 1 and EN = 0 If the SPI clears the EN bit (EN = 0), the device enters Fail Safe mode. Watchdog time out: If WDTB is not toggled within the monitoring timeout period tWDTB, the device enters Fail Safe mode. If the SPI sends a SW reset command (Command byte = 0xFFh), all registers are cleared and the device enters Fail Safe mode. 2.2.5 Standby mode The device is in low consumption state of the digital part. The device enters Standby mode under three conditions: If it is in Fail Safe mode and the SPI sends the goto standby sequence: this mechanism avoids entering Standby mode unintentionally. - In a first communication set UNLOCK = 1 - In the consecutive communication set STBY = 1 and EN = 0 If it is in Normal mode and the SPI sends the goto standby sequence: This mechanism avoids entering Standby mode unintentionally. - In a first communication set UNLOCK = 1 - In the consecutive communication set STBY = 1 and EN = 0 If it is in Sleep mode 2 and at least one input INx is set to one. The outputs are controlled by the direct inputs INx only. The current consumption from VDD drops down to IDDstd (see Table 54: DC characteristics - Mode 1). The digital supply voltage VDD is available (VDD > VDD_POR_ON) but SPI is inactive (no read/Write is possible, the SPI registers are frozen to their last state before entering standby mode). The Standby mode will stay under above condition if at least one INx in logic High. CSN is in inactive High state (independent of MCU). The diagnostics is not available. The protections are fully functional. The outputs are set to unlimited auto-restart mode. Standby mode can be left with three conditions: If VDD falls below VDD_POR_OFF, the device enters Reset mode. If CSN is low for t > tstdby_out, the device wakes up. As the EN bit has been set to 0, the device enters Fail Safe mode and recovers full functionality with command of the outputs and diagnostics. If all direct inputs INx are 0, the device enters Sleep Mode 2 resulting in minimal supply current from VCC and VDD. DocID027886 Rev 7 15/100 93 Functional description VNQ7003SY Transition from Fail-Safe-mode to Standby mode using SPI: two frames needed. Table 6. Frame 1: write CTRL 0x10 Bit 7 Bit 6 Bit 5 Bit 4Frame 1: Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 Command OC1 OC0 0 0 Address 0 0 Data x x GOSTBY UNLOCK x x x EN 0 0 0 1 0 0 0 0 Bit 2 Bit 1 Bit 0 0 0 0 0 Table 7. Frame 2: write CTRL 0x20 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Command OC1 OC0 0 0 Address 0 0 Data x x GOSTBY UNLOCK x x x EN 0 0 1 0 0 0 0 0 Transition from Normal mode to Standby mode using SPI: two frames needed Table 8. Frame 2: write CTRL 0x11 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 Command OC1 OC0 0 0 Address 0 0 Data x x GOSTBY UNLOCK x x x EN 0 0 0 1 0 0 0 1 Bit 2 Bit 1 Bit 0 0 0 0 0 Table 9. Frame 2: write CTRL 0x20 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Command OC1 OC0 0 0 Address 0 0 Data x x GOSTBY UNLOCK x x x EN 0 0 1 0 0 0 0 0 16/100 DocID027886 Rev 7 VNQ7003SY 2.2.6 Functional description Sleep mode 1 The device is in Limp Home state. The device has very low consumption for both digital and power parts. Current consumption from Digital part is nearly zero and the current consumption on VCC is below ISTBY (low supply current). The device enters Sleep mode 1 under one condition: If from Reset mode, all direct inputs INx are going low. The digital supply voltage VDD is not available (VDD < VDD_POR_OFF) and SPI is inactive (the read and write functions are not possible and all registers are cleared and have the reset values). The diagnostics is not available (neither Analogue nor digital diagnostics). The output stages are all off. Protections are inactive. Sleep-mode-1 can be left with two conditions: If VDD rises above VDD_POR_ON, the device enters Fail Safe mode. If at least one of the inputs INx is set to 1, the device enters Reset mode. 2.2.7 Sleep mode 2 The device is in very low consumption state for both digital and power parts. Current consumption from Digital part is below IDDstd and the current consumption on VCC is below ISOFF (low supply current). The digital supply voltage VDD is available (VDD > VDD_POR_ON) but SPI is not active (the read and write functions are not possible and all registers are frozen). CSN is in inactive High state (independent of MCU). The diagnostics is not available (neither analogue nor digital diagnostics). The output stages are all off. Protections are inactive. The device enters Sleep-mode-2 under one condition: If from Standby mode, all direct inputs INx are going low. Sleep mode 2 can be left with three conditions: If VDD falls below VDD_POR_ON, the device enters Reset mode. If CSN is low for t > tstdby_out, the device enters Fail Safe mode. If at least one of the inputs INx is set to 1, the device enters Standby mode. 2.2.8 Battery undervoltage mode This is not an operation mode but a transition step, where power supply voltage is (VCC < VUSD). If the battery supply voltage VCC falls below the undervoltage shutdown threshold (VCC < VUSD) the device enters Battery undervoltage mode. The CurrentSense signal is not available. The output stages are off regardless of SPI status or INx. There are three cases and, depending on the operation mode, the following occurs: 1. From Normal mode and from Fail-safe mode: In these modes the digital supply voltage VDD is available (VDD > VDD_POR_ON). The SPI is active and read/write functions are possible. The SPI diagnostics is available. After entering to the Undervoltage mode, the information about the undervoltage is saved in a flag (VCCUV), the SPI DocID027886 Rev 7 17/100 93 Functional description VNQ7003SY register contents are retained. The SPI-register reading is always possible. If VCC rises above the threshold (VUSD + VUSDhyst) the device returns to the last mode and the flag is cleared (VCCUV). If during this state VDD decreases to VDD < VDD_POR_OFF, the device is reset completely. The last operation mode information is lost, the device logic part is unpowered, therefore after increasing the supply voltage to (VCC > VUSD + VUSDhyst) the operation mode will be Reset mode. If during this state, the INx is changed, the operation mode is not changed and the output state is changed accordingly after VCC recovering. 2. From Standby and Sleep-mode-2 modes: In these modes the digital supply voltage VDD is available (VDD > VDD_POR_ON). The SPI is not active and the registers are frozen. The SPI diagnostics is not available. After entering to the Undervoltage mode, the information about the undervoltage is not saved in a flag (VCCUV). If VCC rises above the threshold (VUSD + VUSDhyst) the device returns to the last mode. If during this state (undervoltage mode) VDD decreases to VDD < VDD_POR_OFF, the device is reset completely. The last operation mode information is lost, the device logic part is unpowered, therefore after increasing the supply voltage to (VCC > VUSD + VUSDhyst) the operation mode will be Reset-mode. If during this state (under voltage mode) the INx is changed, the operation mode is also changed. After VCC recovering, this new operation mode is taken into account. 3. From Reset mode or Sleep-mode1: In this modes the digital supply voltage VDD is not available (VDD < VDD_POR_OFF) and SPI is not active. It is not possible to read/write via SPI, all SPI registers have the reset values. After entering to the Undervoltage mode, the information about the undervoltage is not saved in a flag (VCCUV). If VCC rises above the threshold VUSD + VUSDhyst, the device returns to the last mode. If during this state VDD increases to VDD > VDD_POR_ON, the device is completely reset. After VCC recovering (VCC > VUSD + VUSDhyst), there will be a startup transition. The undervoltage flag (VCCUV) is not saved in the following operation modes: Reset mode, Sleep mode 1, Sleep mode 2 and Standby mode. Figure 3. Battery undervoltage shutdown diagram 18/100 DocID027886 Rev 7 VNQ7003SY Functional description Figure 4. Undervoltage shutdown 2.2.9 Limp Home mode The Reset mode, the Fail Safe mode and the Sleep mode 1 are combined into the Limp home mode. In this mode the chip is able to operate without the connection to the SPI. All transitions between the states in limp home mode are driven by VDD and INx. The outputs are controlled by the direct inputs INx. For a direct entry to the Limp Home mode during Normal operating mode, MCU uses the Watchdog Toggle Bit (WDTB) or dedicated SPI command. Changing the polarity of the WDTB within Watchdog Timeout (tWDTB) keeps the device in Normal mode. For an overview of the operating modes and the triggering conditions please refer to the table below. Table 10. Operating modes Operating mode Entering conditions Startup transition (this is not an operating mode) Reset (Limp Home mode) - Startup mode: VCC > VUSD - Sleep 1: - INx Low to High - Any other mode: VDD < VDD_POR_OFF Leaving conditions Characteristics - VCC > VUSD: reset - (VDD > VDD_POR_ON) and (VCC < VUSD): Fail Safe - - - - - Outputs: OFF SPI: inactive Registers: reset values Diagnostics: not available Reset bit = X - All INx low: sleep 1 - VDD > VDD_POR_ON: Fail Safe - - - - - Outputs: according to INx SPI: inactive Registers: reset values Diagnostics: not available Reset bit = X DocID027886 Rev 7 19/100 93 Functional description VNQ7003SY Table 10. Operating modes (continued) Operating mode Entering conditions Sleep 1 (Limp Home mode) Reset: all INx = 0 - Fail Safe (Limp Home mode) 20/100 - - - - Leaving conditions - VDD > VDD_POR_ON: Fail Safe - INx low to high: reset - Reset or sleep 1: VDD > - VDD_POR_ON - Standby or sleep 2: - CSN low for t > tstdby_out Normal: - EN = 0 or WDTB - toggling timeout or SW- reset VDD < VDD_POR_OFF: reset SPI sequence 1. UNLOCK = 1 2. STBY = 0 and EN = 1: normal SPI sequence 1. UNLOCK = 1 2. STBY = 1 and EN = 0: Standby Normal VDD < VDD_POR_OFF: reset SPI sequence - Fail Safe: SPI 1. UNLOCK = 1 sequence 2. STBY = 1 and EN = 0: - 1. UNLOCK = 1 Standby - 2. STBY = 0 and EN = 1 - EN = 0 or WDTB time out or SW reset: Fail- Safe Standby - - - - - - - - - - - - - Normal: SPI sequence 1. UNLOCK = 1 2. STBY = 1 and EN = 0 - VDD < VDD_POR_OFF: Reset Fail Safe: - CSN low for t > tstdby_out: FailSPI sequence Safe 1. UNLOCK = 1 - All INx low: sleep 2 2. STBY = 1 and EN = 0 Sleep 2: INx low to high DocID027886 Rev 7 Characteristics - - - - - Outputs: OFF SPI: inactive Registers: reset values Diagnostics: not available Low supply current from VDD and VCC - Reset bit = X - Outputs: according to INx - SPI: active - Registers: read/write possible, cleared if entered after SW reset - Diagnostics: SPI possible, CurrentSense diagnostic is not possible - Reset bit = 1 if entered after SW reset or POR, else Reset bit = 0 - Outputs: according to SPI register settings and/or INx - SPI: active - Registers: read/write is possible - Diagnostics: SPI and CurrentSense diagnostic possible - Regular toggling of WDTB is necessary within timeout period tWDTB - Reset bit = 0 - - - - - Outputs: OFF SPI: inactive Registers: frozen Diagnostics: not available Low supply current from VDD and VCC - CSN: High - Reset bit = 0 VNQ7003SY Functional description Table 10. Operating modes (continued) Operating mode Sleep 2 Battery undervoltage (this is not an operating mode) Entering conditions Leaving conditions Characteristics - - - VDD > VDD_POR_OFF: reset - - CSN low for t > tstdby_out: Fail- - Safe - - INx low to high: Standby - - Standby: all INx = 0 Any mode: VCC < VUSD VCC > VUSD + VUSDhyst: back to last mode DocID027886 Rev 7 Outputs: OFF SPI: inactive Registers: frozen Diagnostics: not available Low supply current from VDD and VCC CSN: High Reset bit = 0 - Outputs: OFF and independent from INx and SPI - SPI: as the last mode - Reset bit = 0 21/100 93 Functional description VNQ7003SY Figure 5. Device state diagram 22/100 DocID027886 Rev 7 VNQ7003SY 3 Protections 3.1 Pre-warning Protections If the case-temperature rises above the case-thermal detection pre-warning threshold TCSD, the bit TCASE in the Global Status Byte is set. TCASE is cleared automatically when the case- temperature drops below the case-temperature reset threshold TCR. 3.2 Junction overtemperature (OT) If the junction temperature of one channel rises above the shutdown temperature TTSD, an overtemperature event (OT) is detected. The channel is switched OFF and the corresponding bit in the Address 0x30h - Channel Feedback Status Register (CHFBSR) is set. Consequently, the thermal shutdown bit (bit 4) in the Global Status Byte and the Global Error Flag are set. In Limp Home Mode each output channel works in unlimited auto-restart, whereas in Normal Mode it can be either set as latch-off or programmable time limited auto-restart operations in case of junction overtemperature event. In Auto-restart operation, the output is switched off as described and switches on again automatically when the junction temperature falls below the reset temperature TR. The status bit is latched during OFF-state of the channel in order to allow asynchronous diagnostic and it is automatically cleared when the junction temperature falls below the thermal reset temperature of OT detection TRS. In Latched OFF operation, the output remains switched OFF until the junction temperature falls below TR and a write command to the addressed latched OFF channel is sent (CHLOFFTCRx). The action will clear the corresponding flag in CHLOFFSR and bit 2 in the Global Status Byte. Bit 2 only remains stuck at logic high if another fault condition is present at the same time. In time limited auto-restart, during the programmed time, it reacts as in auto-restart operation mode. After the programmed time expiration, the output remains switched OFF and acts as above described in latch-off mode. DocID027886 Rev 7 23/100 93 Protections VNQ7003SY Figure 6. Thermal shutdown 3.3 Power limitation (PL) If the difference between junction temperature and case temperature (T = Tj - Tc) rises above the power limitation threshold TPLIM, a power limitation event is detected. The channel is switched OFF and the corresponding bit in the Address 0x30h - Channel Feedback Status Register (CHFBSR) is set. Consequently, the Power limitation bits (bit 4) in the Global Status Byte and the Global Error Flag are set. In Limp Home Mode each output channel works in unlimited auto-restart, whereas in Normal Mode it can be either set as latch-off or programmable time limited auto-restart operations in case of power limitation event. In Auto-restart operation, the output is switched off as described and switches on again automatically when the difference of junction temperature and case temperature (T = Tj - TC) decreases below TPLIMR. In OFF-state of the channel, the status bit is latched in order to allow asynchronous diagnostic and is cleared during a Read and Clear command. The payload bits set to 1 into the data byte determine the bits into the register which have to be cleared. In Latched OFF operation, the output remains switched OFF until the difference of junction temperature and case temperature (T = Tj - TC) decreases below TPLIMR and a write command to the addressed latched OFF channel is sent (CHLOFFTCRx). The action will clear the corresponding flag in CHLOFFSR and bit 2 in the Global Status Byte. Bit 2 only remains stuck at logic high if another latch-off condition is present at the same time. In time limited auto-restart, during the programmed time, the device reacts as in auto- restart operation mode. After the programmed time expiration, the output remains switched OFF and acts as above described in latch-off mode. 24/100 DocID027886 Rev 7 VNQ7003SY Protections Figure 7. Power limitation 3RZHUOLPLWDWLRQ 76' 75 756 7380 $)'#43 3/ &XUUHQW/LPLW RXWSXW ,B/,0B+ 21 2)) 21 *$3*36 DocID027886 Rev 7 25/100 93 SPI functional description VNQ7003SY 4 SPI functional description 4.1 SPI communication The SPI communication is based on a standard ST-SPI 16-bit interface, using CSN, SDI, SDO and SCK signal lines. Input data are shifted into SDI, MSB first while output data are shifted out on SDO, MSB first. 4.1.1 Signal description During all operations, VDD must be held stable and within the specified valid range: VDD min to VDD max. Table 11. SPI signal description Name Function This input signal provides the timing of the serial interface. Data present at Serial Data Input Serial clock SCK (SDI) are latched on the rising edge of Serial Clock (SCK). Data on Serial Data Output (SDO) change after the falling edge of Serial Clock (SCK). Serial data input This input signal is used to transfer data serially into the device. It receives data to be written. SDI Values are sampled on the rising edge of Serial Clock (SCK). Serial data output SDO This output signal is used to transfer data serially out of the device. Data are shifted out on the falling edge of Serial Clock (SCK). When this input signal is High, the device is deselected and Serial Data Output (SDO) is high impedance. Driving this input Low enables the communication. The communication must start on a Low level of Serial Clock (SCK). Data are accepted only if exactly 16 bits (or 8 bits Short Frame option) have been shifted in. Note: as per the ST_SPI standard, in case of failing communication: - Stuck @HIGH: If the device is in Normal Mode, a WDTB Timeout will force the device into Fail-safe mode. The Serial Data-Out (SDO) will stay in High impedance (High Z). Any valid communication arrived after this event will be accepted by the device. Chip select CSN - Stuck @LOW: in this case and whatever the mode of the device, a CSN Timeout protection will be activated and force the device to release the SPI bus. Then the Serial Data-Out (SDO) will go into High impedance (High Z). A reset of the CSN Timeout (described as tSHCH parameter in Table 58: Dynamic characteristics Mode 1) is activated with a transition Low to High on CSN pin (or with a Power On Reset or Software reset). With this reset, the Serial Data-Out (SDO) will be released and any valid communication will be accepted by the device. Without this reset, next communication will not be taken into account by the device. 26/100 DocID027886 Rev 7 VNQ7003SY 4.1.2 SPI functional description Connecting to the SPI bus A schematic view of the architecture between the bus and devices can be seen in Figure 9: Bus master and two devices in a normal configuration. All input data bytes are shifted into the device, MSB first. The Serial Data Input (SDI) is sampled on the first rising edge of the Serial Clock (SCK) after Chip Select (CSN) goes low. All output data bytes are shifted out of the device on the falling edge of SCK, MSB first on the first falling edge of the Chip Select (CSN). 4.1.3 SPI mode Supported SPI mode during a communication phase can be seen in the following figure: Figure 8. Supported SPI mode &61 0LFURFRQWUROOHU 63,0DVWHU 6&. 6', 9146< 6ODYH 6'2 &61 6&. 6', 06% 6'2 06% /6% /6% *$3*36 This device can be driven by a micro controller with its SPI peripheral running in the following mode: CPOL = 0, CPHA = 0 DocID027886 Rev 7 27/100 93 SPI functional description VNQ7003SY Figure 9. Bus master and two devices in a normal configuration #64NBTUFS 41*JOUFSGBDFXJUI $10- $1)" $4 4$, 4%* 4$, 4%0 7/24: $4 4%* 4%0 7/24: $4/ $4/ ("1($'5 4.2 SPI protocol 4.2.1 SDI format SDI, Frame 16-bit SDI format during each communication frame starts with a command byte. It begins with two bits of operating code (OC0, OC1) which specify the type of operation (read, write, read and clear status, read device information) and it is followed by a 6 bit address (A0:A5). The command byte is followed by an input data byte (D0:D7). Table 12. Command byte MSB OC1 LSB A5 A4 A3 A2 A1 A0 Table 13. Input data byte MSB D7 LSB D6 D5 D4 D3 D2 D1 D0 SDI, Frame 8 bit SPI Data-In Frame length 8 bits is defined for the device requiring fast write access to single 8 bit register, called SOCR address 0x07h. SDI Frame consists of Input Data Byte content only, no Operation Code + Address is transmitted. 28/100 DocID027886 Rev 7 VNQ7003SY SPI functional description Figure 10. SDI Frame 8 bits '$7$%\WH 06% 4.2.2 WLPH /6% *$3*36 SDO format SDO, Frame 16-bit SDO format during each communication frame starts with a specific byte called Global Status Byte (see Section 4.3.1: Global Status byte description for more details of bit0- bit7). This byte is followed by an output data byte (D0:D7). Table 14. Global status byte MSB bit7 LSB bit6 bit5 bit4 bit3 bit2 bit1 bit0 Table 15. Output data byte MSB D7 LSB D6 D5 D4 D3 D2 D1 D0 SDO, Frame 8-bit SDO Frame of 8 bits consists of GSB content only. Figure 11. SDO Frame 8 bits *OREDO6WDWXV%\WH *6% *6%1 567% 63,( 76' 27 29/ 7&$6( 06% 4.2.3 /2)) 2/2)) )6 /6% *$3*36 Operating code definition The SPI interface features four different addressing modes which are listed in Table 16: Operating codes. DocID027886 Rev 7 29/100 93 SPI functional description VNQ7003SY Table 16. Operating codes OC1 OC0 Meaning 0 0 Write operation 0 1 Read operation 1 0 Read and clear status operation 1 1 Read device information Write mode The write mode of the device allows to write the content of the input data byte into the addressed register (see list of registers in Table 20: RAM memory map). Incoming data are sampled on the rising edge of the serial clock (SCK), MSB first. During the same sequence outgoing data are shifted out MSB first on the falling edge of the CSN pin and subsequent bits on the falling edge of the serial clock (SCK). The first byte corresponds to the Global Status Byte and the second to the previous content of the addressed register. Figure 12. SPI write operation &61 6', 6'2 &RPPDQG%\WH 06% 06% $GGUHVV *OREDO6WDWXV%\WH ELW /6% 06% /6% 06% 'DWD ELW 'DWD SUHYLRXVFRQWHQWRIUHJLVWHU /6% /6% *$3*36 Read mode The read mode of the device allows to read and to check the state of any register. Incoming data are sampled on the rising edge of the serial clock (SCK), MSB first. Outgoing data are shifted out MSB first on the falling edge of the CSN pin and others on the falling edge of the serial clock (SCK). The first byte corresponds to the Global Status Byte and the second to the content of the addressed register. In case of a read mode on an unused address, the global status/error byte on the SDO pin is followed by 0x00h byte. In order to avoid inconsistency between the Global Status byte and the Status register, the Status register contents are frozen during SPI communication. 30/100 DocID027886 Rev 7 VNQ7003SY SPI functional description Figure 13. SPI read operation &61 6', 6'2 'RQWFDUH ELW &RPPDQG%\WH 06% $GGUHVV *OREDO6WDWXV%\WH ELW 06% / 6% 06% 'DWD ELW /6% 06% /6% /6% *$3*36 Read and clear status command The read and clear status operation is used to clear the content of the addressed status register (see Table 20: RAM memory map). A read and clear status operation with address 0x3Fh clears all Status registers simultaneously. Incoming data are sampled on the rising edge of the serial clock (SCK), MSB first. The command byte allows to determine which register content is read and the payload bits set to 1 into the data byte determine the bits into the register which have to be cleared. Outgoing data are shifted out MSB first on the falling edge of the CSN pin and others on the falling edge of the serial clock (SCK). The first byte corresponds to the Global Status byte and the second to the content of the addressed register. In order to avoid inconsistency between the Global Status byte and the Status register, the Status register contents are frozen during SPI communication. Figure 14. SPI read and clear operation 5HDGDQGFOHDUVWDWXV RSHUDWLRQ &61 &RPPDQGE\WH 6', 6'2 06%$GGUHVV/6% 'DWDE\WH ELWV 06%/6% *OREDO6WDWXVE\WH ELWV 'DWDE\WH ELWV 06%/6% 06%/6% *$3*36 Read device information Specific information can be read but not modified during this mode. Accessible data can be seen in Table 21: ROM memory map. Incoming data are sampled on the rising edge of the serial clock (SCK), MSB first. The command byte allows to determine which information is read while the data byte is "don't care". DocID027886 Rev 7 31/100 93 SPI functional description VNQ7003SY Outgoing data are shifted out MSB first on the falling edge of the CSN pin and others on the falling edge of the serial clock (SCK). The first byte corresponds to the Global Status byte and the second to the content of the addressed register. Figure 15. SPI read device information &61 &RPPDQG%\WH 6', 6'2 06% 06% $GGUHVV *OREDO6WDWXV%\WH ELW / 6% 06% /6% 06% 'RQWFDUH ELW 'DWD ELW /6% /6% *$3*36 4.2.4 Special commands 0xFF -- SW-Reset: set all control registers to default An Opcode `11' (read device information) addressed at `111111' forces a Software Reset of the device. An OpCode '11' at address '111111' with data field equal to '11111111' the SPI frame is recognized as a frame error and SPIE bit of GSB is set. Table 17. 0xFF: SW_Reset Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 1 1 Command OC1 OC0 1 1 Address 1 1 1 1 0xBF -- clear all status registers (RAM access) When an OpCode `10' (read and clear operation) at address b'111111 is performed. Table 18. Clear all status registers (RAM access) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 1 1 Command OC1 OC0 1 0 Address 1 1 1 1 Note: Reset Value = the value of the register after a power on. Note: Default value = the default value of the register. Currently this is equivalent to the Reset value. 32/100 DocID027886 Rev 7 VNQ7003SY SPI functional description Note: Cleared register = explicitly read and clear of the register, if it is not write protected. 4.3 Register map Device contains a set of RAM registers used for device configuration, the device status and ROM registers for device identification. Since ST-SPI is used, Global Status byte defines the device status, containing fault information. 4.3.1 Global Status byte description The data shifted out on SDO during each communication starts with a specific byte called Global Status Byte. This one is used to inform the microcontroller about global faults which can happen at channel-side level (i.e. like thermal shutdown, OLOFF...) or on the SPI interface (like Watchdog monitoring timeout event, communication error,...). This specific register has the following format. Table 19. Global status byte Bit 7 6 Name Global Status Bit Not Reset bit Reset Content 0 The GSBN is a logically NOR combination of Bit 0 to Bit 6. This bit can also be used as Global Status Flag without starting a complete communication frame as it is present directly after pulling CSN low. 1 The RSTB indicates a device reset. In case this bit is set, all internal Control Registers are set to default and kept in that state until the bit is cleared. The Reset bit is automatically cleared by any valid SPI communication 5 SPI Error 0 The SPIE is a logical OR combination of errors related to a wrong SPI communication (SCK count and SDI stuck at errors). The SPIE is automatically cleared by a valid SPI communication. 4 Thermal shutdown (OT) or Power limitation (PL) or VDS 0 This bit is set in case of thermal shutdown, power limitation or in case of high VDS (VDS) at turn-off detected on any channel. The contribution of high VDS failure is maskable. 3 TCASE 0 This bit is set if the frame temperature is greater than the threshold and can be used as a temperature pre-warning. The bit is cleared automatically when the frame temperature drops below the case-temperature reset threshold (TCR). 2 Latch OFF (LOFF) 0 The Device Error bit is set when one or more channels are latched OFF 1 Open-load at offstate or output shorted to VCC 0 This bit is set in case of open-load off-state or output shorted to VCC condition detected on any channel 0 FailSafe 1 The bit is set in case device operates in Fail Safe Mode DocID027886 Rev 7 33/100 93 SPI functional description VNQ7003SY Note: The FFh or 00h combinations for the Global Status Byte are not possible, exclusive combination exists between bit 7 and bit 0 - bit 6. Consequently a FFh or 00h combination for the Global Status Byte must be detected by the microcontroller as a failure (SDO stuck to GND or to VDD or loss of SCK). 4.3.2 RAM RAM registers can be separated according to the frequency of usage init - register is read/ written during initialization phase (single shot action) continuous - read/ write/ read and clear registers often accessed, applying outputs control and diagnostic rare - read/ read and clear status of device registers accessed on demand (in case of failure) Table 20. RAM memory map Address Name Access Content Access type Reset value Control registers 00h CTRL Read/Write Device enable, standby, protected init 0x00 01h DIENCR Read/Write Direct Input Enable Control init 0x00 02h OLOFFC R Read/Write Open-load OFFstate Control init 0x00 03h CCR Read/Write Channel Control init 0x00 FASTSW Read/Write CR Fast Switching Control Register init 0x00 continuous 0x00 continuous 0x00 04h 05h 06h RESERVED CSMUXC CurrentSense Read/Write R Multiplexer Control 07h SOCR Read/Write SPI Output Control 08h CHLOFF TCR0,1 Read/Write Channel Latch OFF Timer Control init 0x00 09h CHLOFF TCR2,3 Read/Write Channel Latch OFF Timer Control init 0x00 ... area not used Status registers 2Fh DIENSR Read only Direct Input Status rare 0x00 30h CHFBSR Read/Clear Channel Feedback Status Register continuous 0x00 31h STKFLTR Read/Clear Open-load OFFstate/Stuck to VCC rare 0x00 32h CHLOFF SR Channels latch-off status register rare 0x00 33h VDSFSR Read/Clear VDS feedback rare 0x00 34/100 Read only DocID027886 Rev 7 VNQ7003SY SPI functional description Table 20. RAM memory map (continued) Address Name 34h GENSR Access Read/Clear ... Content Access type Generic Status Reset value rare 0x00 continuous 0x00 not used area other registers 3Eh 3Fh RESERVED CONFIG Read/Write Configuration Register, Note: Any command (write, read or read and clear status) executed on a "not used". RAM register, i.e. a not assigned address, does not have any effect: there is no change in the Global Status byte (no communication error, no error flag). The data written to this address (2nd byte of SDI frame) is ignored. The data read from this address (2nd byte of SDO frame) contains 00, independent of what has been written previously to this address. Note: A write command on "don't care" bits of an assigned RAM register address does not have any effect: There is no change on the Global Status byte. The data written to the "don't care bits" is ignored. The content of the "don't care bits" remains at "0" independent of the data written to these bits. 4.3.3 ROM This memory is used for device identification. Table 21. ROM memory map Address Name Description Access Content 00h Company code Indicates the code of STM company Read only 00H 01h Device Family indicates the product family Read only 01H Read only 56H Read only 48H 02h 03h 04h Product Code Indicates the first code of the product 1 Product Code Indicates the second code of the product 2 Product Code 3 ... 0Ah Indicates the third code of the product Read only 31H Read only 03H not used area Version Silicon version ... not used area 10h SPI Mode Different Modes of the SPI (see chapter `SPI Modes') Read only 18H 11h WD Type 1 Indicates the type of WatchDog used in the Read only 46H 12h not used area DocID027886 Rev 7 35/100 93 SPI functional description VNQ7003SY Table 21. ROM memory map (continued) Address Access Content 13h WD bit position Indicates the address of the 1 register containing the WD Name Description Read only 7FH 14h WD bit position Indicates the position of the 2 WD toggle bit Read only C0H ... not used area 20h SPI CPHA Indicates the polarity and phase of the SPI interface Read Only 55H 3Eh GSB Options Options of GSB byte (standard GSB definition) Read Only 00H 3Fh Advanced OP. Code -- -- 4.3.4 -- SPI modes By reading out the <SPI Mode> register general information of SPI usage of the Device Application Registers can be read. Table 22. SPI Mode Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 BR DL2 DL1 DL0 SPI8 0 S1 S0 SPI Burst Read Table 23. SPI Burst Read Bit 7 Description 0 BR disabled 1 BR enabled The Burst Read is not implemented in this product so this bit is disabled. SPI Data Length The SPI Data Length value indicates the length of the SCK count monitor which is running for all the accesses to the Device Application Registers. In case a communication frame with an SCK count is not equal to the reported one, the device will lead to a SPI Error and the data will be rejected. The Frame Length is specified on 3 bits in SPI Mode register located in ROM part. The 16bit SPI communication is implemented in this product so these bits are `001'. 36/100 DocID027886 Rev 7 VNQ7003SY SPI functional description Table 24. SPI Data Length Bit 6 Bit 5 Bit 4 DL2 DL1 DL0 0 0 0 Invalid 0 0 1 16bit SPI 0 1 0 24bit SPI Description ... 1 ... 1 1 64bit SPI SPI 8 bit Frame The SPI 8 bit Frame bit indicates if an 8 bit Frame communication is available. The intention of an 8 bit Frame enhancement is to provide fast write access to one 8 bit register, which is very often rewritten with new content. SOCR register address is predefined as addressed register during 8 bit SPI Communications. Table 25. SPI 8 bit Frame Bit 3 Description SPI8 0 8 bit Frame option not available 1 8 bit Frame option is available The SPI 8 bit Frame is implemented in this product so this bit is equal to '1'. A short Frame with a Data Field equal to '00000000' is rejected and considered as a SPI Frame Error condition. Data Consistency Check (Parity/CRC) For some devices a Data Consistency Check is required. Therefore either a parity-check or for very sensitive systems a CRC may be implemented. It is defined on 2 bits, in SPI Mode register located in ROM Part. A check is then applied on the incoming frame (SDI) while a calculation elaborated on one/multiple bits is done and integrated on the outgoing frame (SDO). Table 26. SPI Data Consistency Check Bit 1 Bit 0 Description S1 S0 0 0 not used 0 1 Parity used 1 0 CRC used 1 1 Invalid DocID027886 Rev 7 37/100 93 SPI functional description VNQ7003SY In case either the Parity or the CRC check is implemented it is always located at the end of the communication. As these two checks are not implemented in the product, the two bits are equal to '00'. 4.4 Output switching slopes control Outputs switching slopes are set by configuration register FASTSWCR. Address 0x04h - Fast Switching Configuration Register (FASTSWCR). The FASTSWCR allows configuring each channel in fast switching mode. The typical switching slopes are shown in the following table: Table 27. Switching slopes FASTSWCR Channel 0,1 (V/s) Channel 2, 3 (V/s) 0 0.30 0.20 1 0.45 0.30 4.5 Output control Depending on the actual device mode, outputs can be controlled by SPI register or Direct Input INx. 1. SPI register SOCR - in normal mode outputs can be turned ON/OFF, applying Bit[n] = 1/0 [n]: is the related channel, n = 0 for the channel 0, and n = 3 for channel 4 Example 1: Turning ON channel 1 and 2 with turning OFF others (without taking in consideration the PWM or phase shifting) Table 28. Write SOCR 0x06 Bit7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 1 1 1 Command OC1 OC0 0 0 Address 0 0 0 Data x x x x SOCR3 SOCR2 SOCR1 SOCR0 0 0 0 0 0 1 1 0 Example 2: Turning ON channel 0 without changing other channels status Dummy = Read SOCR Dummy = [Dummy.OR.0x01] & 0x3F => Dummy = b00000111 38/100 DocID027886 Rev 7 VNQ7003SY SPI functional description Table 29. Write SOCR Dummy Bit7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 1 1 1 Command OC1 OC0 0 0 Address 0 0 0 Data 2. x x x x SOCR3 SOCR2 SOCR1 SOCR0 0 0 0 0 0 1 1 1 Direct Input INx - in Fail safe, Standby and Reset modes, turn ON/OFF the outputs by applying high, respectively low, logic levels to dedicated pin. While in normal mode, output can use INx pin to control output if corresponding bit in DIENCR is at logic high level. Then this truth table specifies output state: Table 30. Truth table DIENCRx SOCRx INx OUTPUTx state 1 1 X ON 1 0 L OFF 1 0 H ON 0 1 X ON 0 0 X OFF The output channels 0 and 1 can be configured to operate in BULB or LED mode using the Channel Control Register (CCR). If the relevant bit in CCR is 0, the output is configured in BULB mode, if it is set to 1, the output is configured in LED mode. DocID027886 Rev 7 39/100 93 SPI functional description VNQ7003SY Figure 16. VNQ7003SY: 4-channel direct input block diagram 63,5HJLVWHU ',(1&5 'LUHFW,QSXW(QDEOH&RQWURO5HJLVWHU ',(1&5 ',(1&5 ',(1&5 ',(1&5 'LUHFW ,QSXW 25 *DWH'ULYHU &KDQQHO 'LUHFW ,QSXW 25 *DWH'ULYHU &KDQQHO 'LUHFW ,QSXW 25 *DWH'ULYHU &KDQQHO 'LUHFW ,QSXW 25 *DWH'ULYHU &KDQQHO ',(1675 ',(1675 ',(1675 ',(1675 287387 287387 287387 287387 63,5HJLVWHU 62&5 63,2XWSXW&RQWURO5HJLVWHU 63,5HJLVWHU ',(165 'LUHFW,QSXW6WDWXV5HJLVWHU *$3*&)7 4.6 Control registers 4.6.1 Address 0x00h -- Control Register (CTLR) Table 31. CTLR -- Control Register Bit Access Reset 7 Reserved Name -- -- 6 Reserved -- -- Content 5 GOSTBY R/W 0 Go to Standby mode 1: Enter Standby mode It is necessary to do 2 write accesses to enter standby: 1. Write UNLOCK = 1 2. Write GOSTBY = 1 and EN = 0 4 UNLOCK R/W 0 Unlock bit, has to be set before GOSTBY or EN can be set 3 Reserved -- -- 40/100 DocID027886 Rev 7 VNQ7003SY SPI functional description Table 31. CTLR -- Control Register (continued) Bit Access Reset 2 CTDTH1 R/W 0 1 CTDTH0 R/W 0 0 4.6.2 Name EN R/W Content Case Thermal Detection Threshold These bits allow to configure the case thermal detection of the device. Three temperature thresholds are available by programming these two bits. CDTH1 CTDH0 Detection temp 0 0 120 C 0 1 130 C 1 X 140 C Enter Normal mode 1: Normal mode 0: Fail Safe mode It is necessary to do 2 write accesses to enter Normal mode: 1. Write UNLOCK = 1 2. Write EN = 1 and GOSTBY = 0 0 Address 0x01h -- Direct Input Enable Control Register (DIENCR) Table 32. DIENCR -- Direct Input Enable Control Register Bit Name Access Reset 7 Reserved -- -- 6 Reserved -- -- 5 Reserved -- -- 4 Reserved -- -- 3 DIENCR3 R/W 0 2 DIENCR2 R/W 0 1 DIENCR1 R/W 0 0 DIENCR0 R/W 0 Note: Content Reserved The DIENCR enables the control of the corresponding output channel by the direct input. 1: parallel input INx controls OUTPUTx 0: function disabled Please refer also to Table 30: Truth table. DocID027886 Rev 7 41/100 93 SPI functional description 4.6.3 VNQ7003SY Address 0x02h -- Open-load OFF-State Control Register (OLOFFCR) Table 33. OLOFFCR -- Open-load OFF-state control register Bit Name Access Reset 7 Reserved -- -- 6 Reserved -- -- 5 Reserved -- -- 4 Reserved -- -- 3 OLOFFCR3 R/W 0 2 OLOFFCR2 R/W 0 1 OLOFFCR1 R/W 0 0 CCRO R/W 0 4.6.4 Content Reserved The OLOFFCR enables an internal pull-up current generator to distinguish between the open-load OFF-state fault and the output shorted to VCC fault. 1: Pull-up current generator enabled for OUTPUTX 0: Pull-up current generator disabled for OUTPUTX Address 0x03h -- Channel Control Register (CCR) Table 34. CCR -- Channel control register Bit Name Access Reset 7 Reserve -- -- 6 Reserve -- -- 5 Reserve -- -- 4 Reserve -- -- 3 Reserve -- -- 2 Reserve -- -- 1 CCR1 R/W 0 0 CCR0 R/W 0 4.6.5 Content Reserved The CCR selects the BULB or LED mode for the corresponding output. 1: LED mode selected for OUTPUTX 0: BULB mode selected for OUTPUTX Address 0x04h -- Fast Switching Configuration Register (FASTSWCR) Table 35. FASTSWCR -- Fast Switching Configuration Register Bit Name Access Reset 7 Reserved -- 0 6 Reserved -- 0 5 Reserved -- 0 4 Reserved -- 0 3 FASTSWCR3 R/W 0 2 FASTSWCR2 R/W 0 1 FASTSWCR1 R/W 0 0 FASTSWCR0 R/W 0 42/100 Content Reserved The FASTSWCR allows to configure each channel in fast switching mode 1: Fast Switch 0: Normal Switch DocID027886 Rev 7 VNQ7003SY 4.6.6 SPI functional description Address 0x06h -- CurrentSense Multiplexer Control Register (CSMUXCR) Table 36. CSMUXCR -- CurrentSense Multiplexer Control Register Bit Name Access Reset 7 Reserved -- 0 6 Reserved -- 0 5 Reserved -- 0 4 Reserved -- 0 3 MUXEN R/W 0 2 R/W 0 1 R/W 0 R/W 0 MUXCH 0 Content Reserved The MUXEN enables the CurrentSense output. Monitored channel is selected by MUXCH bits (0..2) Mux channel selection: encoding. MUXCH = 0..3 - correspond to output channel monitor MUXCH = 4..7 reserved b0 ~LSB, b3 ~MSB Table 37. Truth table for CurrentSense Mux Control b2 b1 b0 0 0 0 CH0 0 0 1 CH1 0 1 0 CH2 0 1 1 CH3 4.6.7 CurrentSense enable Address 0x07h -- SPI Output Control Register (SOCR) Table 38. SOCR -- SPI Output Control Register Bit Name Access Reset 7 Reserved -- -- 6 Reserved -- -- 5 Reserved -- -- 4 Reserved -- -- 3 SOCR3 R/W 0 2 SOCR2 R/W 0 1 SOCR1 R/W 0 0 SOCR0 R/W 0 Content Reserved The SOCR register controls the output drivers in Normal Mode. One bit per channel and the dx corresponds to channel-x. 1: The corresponding output is enabled 0: The corresponding output is disabled Please refer also to Table 30: Truth table. DocID027886 Rev 7 43/100 93 SPI functional description 4.6.8 VNQ7003SY Address 0x08h -- Channel Latch OFF Timer Control Register (ch0, ch1) (CHLOFFTCR0,1) In Normal Mode, the output behavior in case of power limitation or thermal shutdown is programmable, as latch-off, time limited auto-restart (tblanking). The default mode is the latch- off mode. In latched off-state the fault has to be cleared to re-enable the output channel after an overtemperature or power limitation event through a new value written through SPI command at CHLOFFTCRx register. In fail-safe state, the device operates in unlimited auto-restart mode. Example 3: Table 39. Channel configuration Bit x3 Bit x2 Bit x1 Bit x0 Blanking time window duration 0 0 0 0 0x0 0 ms (latch-off configuration - default) 0 0 0 1 0x1 17 ms 0 0 1 0 0x2 34 ms 0 0 1 1 0x3 51 ms .... 1 1 1 0 0xE 238 ms 1 1 1 1 0xF 255 ms Table 40. CHLOFFTCR0,1 -- Channel Latch OFF Timer Control Register (ch0, ch1) Bit Name Access Reset Content 7 CHLOFFTCR13 R/W 0 CHLOFFTCR1x It configures the blanking time duration in case of power limitation or overtemperature for the corresponding output. 6 CHLOFFTCR12 R/W 0 5 CHLOFFTCR11 R/W 0 4 CHLOFFTCR10 R/W 0 3 CHLOFFTCR03 R/W 0 2 CHLOFFTCR02 R/W 0 1 CHLOFFTCR01 R/W 0 It configures the blanking time duration in case of the power limitation for the corresponding output. 0 CHLOFFTCR00 R/W 0 CHLOFFTCR00 - CHLOFFTCR03: for channel 0 4.6.9 CHLOFFTCR10 - CHLOFFTCR13: for channel 1 CHLOFFTCR0x Address 0x09h -- Channel Latch OFF Timer Control Register (ch2, ch3) (CHLOFFTCR2,3) Table 41. CHLOFFTCR2,3 -- Channel Latch OFF Timer Control Register (ch2, ch3) Bit Name Access Reset 7 CHLOFFTCR33 R/W 0 6 CHLOFFTCR32 R/W 0 5 CHLOFFTCR31 R/W 0 4 CHLOFFTCR30 R/W 0 44/100 Content CHLOFFTCR3x It configures the blanking time duration in case of the power limitation for the corresponding output. CHLOFFTCR30 - CHLOFFTCR33: for channel 3 DocID027886 Rev 7 VNQ7003SY SPI functional description Table 41. CHLOFFTCR2,3 -- Channel Latch OFF Timer Control Register (ch2, ch3) (continued) Bit Name Access Reset 3 CHLOFFTCR23 R/W 0 2 CHLOFFTCR22 R/W 0 1 CHLOFFTCR21 R/W 0 0 CHLOFFTCR20 R/W 0 Content CHLOFFTCR2x It configures the blanking time duration in case of the power limitation for the corresponding output. CHLOFFTCR20 - CHLOFFTCR23: for channel 2 DocID027886 Rev 7 45/100 93 Diagnostic 5 VNQ7003SY Diagnostic Device is capable to provide digital diagnostic information through SPI interface and analogue diagnostic signal using CurrentSense signal. 5.1 Analogue diagnostic The Analogue output signal provides: Mirror Current - output in current mode, proportional of the load current in normal operation, according to K-ratio No signal - output is in High Z (tri-state) The CSMUXCR register is used to enable the CurrentSense feature of each channel to the CurrentSense pin. Each channel integrates an analog CurrentSense function which can be connected to the CurrentSense pin by setting the MUXEN bit (bit 3) and by setting the corresponding channel in the MUX channel selection bits (bits 0, 1 and 2) in the address 0x06h - CurrentSense Multiplexer Control Register (CSMUXCR). 5.2 Digital diagnostic Global status byte (GSB) provides preliminary status of device every SPI communication with device. It informs about device actual mode (normal/ fail-safe). 46/100 DocID027886 Rev 7 VNQ7003SY Diagnostic Figure 17. Diagnostic registers :DWFK'RJ 9'6FKDQQHO &21),* 5HJLVWHU PDVN ' ' ' ' ' 899FF :DWFKGRJ &RPP(UURU 63,( *6%1 ' &KLS5HVHW 567% ' 25 25 27 ' 3/ 7FDVH ' /2)) ' *OREDO6WDWXV%\WH *6% 9'6 *OREDO 6WDWXV %LW1RW *6%1 2/2)) 2/2))6&WR9FF 25 6&WR9FF ' )DLO6DIH ' 27 3/ 25 2/2)) 6&WR9FF 9'6 67.)/75 &+)%65 9'6)65 2SHQORDG2))VWDWH6WXFNWR 9&&6WDWXV5HJLVWHU &KDQQHO)HHGEDFN 5HJLVWHU 96')HHGEDFN 5HJLVWHU *$3*&)7 By reading additional status registers, more detailed information is provided. Status information is stored in the status registers. DocID027886 Rev 7 47/100 93 Diagnostic 5.2.1 VNQ7003SY Status registers Table 42. Status registers Address 0x2F Name DIENSR Access Description Read Direct Input Status register. This register is a real time one and reads back the Input state for each direct input. The register content is cleared if the battery voltage is not present. 0x30 CHFBSR Read/Clear Channel Feedback Status Register Each bit specifies channel fault state, providing a logical "OR" combination of VDS, PWLM, OT failure flags related to OUTPUTx. The contribution of VDS failure can be masked through CONFIG register settings. 0x31 STKFLTR Read/Clear Open-load OFF-state/ Stuck to VCC Status Register Provides information about open load or stuck to VCC, depending on the configuration of the OLOFFCR register. Channels latch-off status register One bit per channel. In case a channel is latch-off, this flag is set and is readable by MCU In latched-off state the fault has to be cleared through a Write operation of dedicated CHLOFFTCRx register to re-enable the output channel after an overtemperature or power limitation event 0x32 CHLOFFSR Read 0x33 VDSFSR Read/Clear VDS feedback status register Each bit specifies channel fault state in case of high voltage drop across PowerMos (VDS) Read/Clear Generic Status register Bit 7: Undervoltage warning flag Bit 6: Reset warning bit. This bit is set in case of Reset event (HW Reset or SW Reset). Bit 5: SPI Error warning bit. Bit 6 & Bit 5 have to be cleared through a Read & Clear command. Bit 7 is a real time bit. 0x34 GENSR Note: Regarding CHLOFFSR register, Time limited auto-restart and for further information about the Configurable blanking time, please refer to the related chapter. 5.3 Over load (VDS high voltage, Over Load (OVL)) During low duty cycle PWM operation on a shorted load, ON-time may be too short to allow power limitation or overtemperature detection. CurrentSense output is disabled. This would make detection of over load condition impossible. To overcome this, always when an output channel is turned OFF, the voltage drop on the PowerMOS (VDS) is measured. If VDS (voltage across PowerMOS output stage) exceeds the threshold defined by the parameter 48/100 DocID027886 Rev 7 VNQ7003SY Diagnostic VDS_OVL, an over load condition is detected. The corresponding bit in the over load status register VDSFSR (address 0x33h) is set. The same information is saved in the Channel Feedback Status Register (CHFBSR), if it is not masked in the CONFIG register. Consequently, the bit 4 in the Global Status Byte and the Global Error Flag are set, if it is not masked in the CONFIG register. The VDSFSR is a warning and the channel can be switched on again even if the VDSFSRx bit is set. The VDSFSRx bit remains unchanged until a read and clear command on VDSFSR is sent by the SPI or until the output is turned off the next time, when VDS is evaluated again. In case of low duty cycle PWM operation (i.e. 3% typical at 200 Hz in Bulb mode), VDS might be greater than a threshold defined by the parameter VDS_OVL even if the output is not in over load state so that a false warning is issued. Please refer to the Section 4.3.1: Global Status byte description, Section 5.7: Address 0x30h -- Channel Feedback Status Register (CHFBSR) and Section 5.10: Address 0x33h -- VDS Feedback Status Register (VDSFSR). 5.4 Open-load ON-state detection The open- load ON-state is performed by reading the CurrentSense. 5.5 Open-load OFF-state detection If the output voltage VOUT in OFF-state of the output is greater than the open-load detection threshold voltage VOL, an open-load OFF-state / Stuck to VCC event is detected. The corresponding bit in the Openload OFF-state / Stuck to VCC status register STKFLTR (address 0x31h) is set. Consequently, the OLOFF bit (bit 1) in the Global Status Register and the Global Status Bit Not are set. To avoid false detection, the diagnosis starts after turn-off of a channel with an additional delay tDOLOFF. To distinguish between an open-load OFF-state event and a short to VCC condition, an internal pull-up current generator can be enabled for each channel by setting the corresponding bit in the open-load OFFstate control register (OLOFFCR, address 0x02h). The activated pull-up current generators are active in Normal Mode, in Fail Safe Mode and in Standby Mode. In Sleep Mode 2, the current generators are switched off. The register contents, however, are saved also in Sleep Mode 2, consequently the current generators are reactivated after a return to Standby or a wakeup to Fail Safe Mode. A hardware reset (VDD < VDD_POR_OFF) or a software reset (Command byte = FFh) clears all register contents and hence the current generators are switched off. DocID027886 Rev 7 49/100 93 Diagnostic VNQ7003SY Figure 18. Open-load OFF-state detection 41*3FHJTUFS0-0''$3 0QFO-PBE0''TUBUF$POUSPM3FHJTUFS 7%4 7$$ 065 (/% 7065 *$3*&)7 Table 43. STKFLTR state With internal pull-up generator Without internal pull-up generator "0" / no fault "0" / no fault Case 2: no load "1" / fault "0" / no fault Case 3: output shorted to VCC "1" / fault "1" / fault Case 1: load connected 5.6 Address 0x2Fh -- DIENSR: Direct Input Status register Table 44. DIENSR -- Direct Input Status register Bit Name Access Reset 7 Reserved -- 0 6 Reserved -- 0 5 Reserved -- 0 4 Reserved -- 0 3 DIENSTR3 R 0 2 DIENSTR2 R 0 1 DIENSTR1 R 0 0 DIENSTR0 R 0 50/100 Content Reserved The DIENSTRx registers read back the status of the Direct Inputs. 1: The corresponding input is HIGH 0: The corresponding input is LOW DIENSTR0 is the direct input status of the channel 0 DocID027886 Rev 7 VNQ7003SY 5.7 Diagnostic Address 0x30h -- Channel Feedback Status Register (CHFBSR) Table 45. CHFBSR -- Channel Feedback Status Register Bit Name Access Reset 7 Reserved -- 0 6 Reserved -- 0 5 Reserved -- 0 4 Reserved -- 0 3 CHFBSR3 R/C 0 2 CHFBSR2 R/C 0 1 CHFBSR1 R/C 0 0 CHFBSR0 R/C 0 5.8 Content Reserved The CHFBSRx provides a logical "OR" combination of VDS, PL, OT failure flags related to OUTPUTx. The contributions of VDS failure flags are maskable through CONFIG register settings. CHFBSRx = 1: Channel OUTPUTx on failure CHFBSRx = 0: Channel OUTPUTx no failure The bits are refreshed continuously in ON-state and latched in OFFsate. The bits are not set in case of latch-off configuration and if contribution of VDS failure flags is masked. In order to clear the bit in OFF-state, it is necessary to send a ReadClear command Address 0x31h -- Open-load OFF-State / Stuck to VCC Status Register (OLOFFCR) Table 46. STKFLTR -- Open-load OFF-State / Stuck to VCC Status Register Bit Name Access Reset 7 Reserved -- 0 6 Reserved -- 0 5 Reserved -- 0 4 Reserved -- 0 3 OLOFFSR3 R/C 0 2 OLOFFSR2 R/C 0 1 OLOFFSR1 R/C 0 0 OLOFFSR0 R/C 0 Content Reserved The OLOFFCR bit is set in OFF-state after turn-off delay, the tDOLOFF is elapsed if VOUT > VOL. It gives an information about open load or a stuck to VCC which depends on the configuration of the OLOFFCR register (for details refer to the functional description). The bit is continuously refreshed in OFF-state and it is latched during ON-state. In order to clear the bit in ON-state it is necessary to send a Read and Clear command. 1: Open-load in OFF-state or stuck to VCC condition occurred for OUTPUTX 0: No fault detected DocID027886 Rev 7 51/100 93 Diagnostic 5.9 VNQ7003SY Address 0x32h -- Channels latch-off status register (CHLOFFSR) Table 47. CHLOFFSR -- Channels latch-off status register Bit Name Access Reset 7 Reserved -- 0 6 Reserved -- 0 5 Reserved -- 0 4 Reserved -- 0 3 CHLOFFSR3 R 0 2 CHLOFFSR2 R 0 1 CHLOFFSR1 R 0 0 CHLOFFSR0 R 0 5.10 Content Reserved Latch OFF flag register. One bit per channel. - In case of latch-OFF of a channel because of power-limitation or overtemperature, this flag is set and readable by MCU - In latch-off state the fault has to be cleared through a Write operation of dedicated CHLOFFTCRx register to re-enable the output channel after an overtemperature or power limitation event. A SW reset event clears the content of the register Address 0x33h -- VDS Feedback Status Register (VDSFSR) Table 48. VDSFSR -- VDS Feedback Status Register Bit Name Access Reset 7 Reserved -- 0 6 Reserved -- 0 5 Reserved -- 0 4 Reserved -- 0 3 VDSFSR3 R/C 0 2 VDSFSR2 R/C 0 1 VDSFSR1 R/C 0 0 VDSFSR0 52/100 R/C 0 Content Reserved VDS Feedback status. One bit per channel. - The VDSFSRx bit is set if, at the instant when the channel is commanded off or is latched-off, the VCC - VOUT voltage drop exceeds VDS_OVL threshold. The bit is latched until the next turn OFF. In order to clear the bit it is necessary to send a read and clear command. The VDSFSRx bit is set to: 1: High VDS detected on OUTPUTx 0: no fault detected Note: As the status register is not updated while CSN is low, it is possible that the update of the VDSFSR is delayed until the next time it is commanded off, if the PowerMOS is turned off during an SPI- frame. DocID027886 Rev 7 VNQ7003SY 5.11 Diagnostic Address 0x34h -- Generic Status Register (GENSR) Table 49. GENSR -- Generic Status Register Bit Name Access Reset Content 7 VCCUV R 0 VCC undervoltage detection, Active High: this bit is related to the VCC undervoltage detection and is real time, means that it is set when VCC < VUSD and it is automatically reset as soon as VCC > VUSD + VUSDHYST. This bit sets the Global Error Flag of the GSB. 6 RST R/C 0 Active High: this bit is high in case of chip reset (hardware reset due to a loss of VREG supply or software reset). This bit is set until a Read and Clear Command is performed. Active High: this bit is set at end of Communication in case of wrong number of clock cycles during a communication frame or invalid bus condition or SDI stuck at High or Low conditions. This bit is set until a Read and Clear is performed. 5 SPIE R/C 0 4 Reserved -- 0 3 Reserved -- 0 2 Reserved -- 0 1 Reserved -- 0 0 Reserved -- 0 5.12 Address 0x3Fh -- Configuration Register (CONFIG) Table 50. CONFIG -- Configuration Register Bit Name Access Reset 7 Reserved -- 0 Reserved 6 Reserved -- 0 Reserved 5 Reserved -- 0 Reserved 0 Masks the contribution of the VDS status bit in the channel feedback status register and Global Status Byte For channel 3 1: VDS bit is masked 0: VDS bit not masked 0 Masks the contribution of the VDS status bit in the channel feedback status register and Global Status Byte For channel 2 1: VDS bit is masked 0: VDS bit not masked 0 Masks the contribution of the VDS status bit in the channel feedback status register and Global Status Byte For channel 1 1: VDS bit is masked 0: VDS bit not masked 4 3 2 VDSMASK3 VDSMASK2 VDSMASK1 R/W R/W R/W Content DocID027886 Rev 7 53/100 93 Diagnostic VNQ7003SY Table 50. CONFIG -- Configuration Register Bit 1 0 Name VDSMASK0 WDTB Access R/W R/W Reset Content 0 Masks the contribution of the VDS status bit in the channel feedback status register and Global Status Byte For channel 0 1: VDS bit is masked 0: VDS bit not masked 0 Changing the polarity of the Watchdog Toggle Bit (WDTB) within Watchdog Timeout (WDTO linked to tWDTB parameter, seeTable 58: Dynamic characteristics - Mode 1) keeps the device in NORMAL operating mode Figure 19. Diagnostic flowchart based on GSB 3UHOLPLQDU\ GLDJQRVLV 3UHOLPLQDU\GLDJQRVLVGRHVQRWGLVWLQJXLVK ZKLFKGHYLFHFKDQQHOUHSRUWVHUURU &KHFN*OREDO6WDWXV%\WH *6% $GGLWLRQDOHUURUIODJIURPRWKHUVWDWXV UHJLVWHUVDUHSURYLGHG 1RHUURU 1RHUURU (UURURQ GHGLFDWHGELW RUELW )URP*6%IURPRWKHU VWDWXVUHJLVWHU <HV &KLS5HVHW (QG 1RHUURUVGHWHFWHG 63,(UURU 2YHUWHPSHUDWXUH 3RZHUOLPLWDWLRQ 2YHU/RDG9'6 7&$6( &KDQQHO /DWFK2)) 2SHQORDGLQ2)) VWDWHVKRUWWR9FF )DLO6DIH 8QGHUYROWDJH 9FF *$3*&)7 54/100 DocID027886 Rev 7 VNQ7003SY Diagnostic Figure 20. Diagnostic flowchart for open-load off-state respectively stuck to VCC failure 'HWDLOHGGLDJQRVLVLQ2))VWDWH (QDEOHLQWHUQDO3XOOXSFXUUHQWJHQHUDWRUZULWH WR 2/2))&5 FRQWUROUHJLVWHU 5HDG2SHQORDGLQRIIVWDWH 67.)/75 6WRUH2SHQORDGLQRII VWDWH 6WRUHG2))6WDWH 'LVDEOHLQWHUQDO3XOOXSFXUUHQWJHQHUDWRUZULWH WR 2/2))&5 FRQWUROUHJLVWHU 5HDG2SHQORDGLQRIIVWDWH 67.)/75 1RHUURU (QG 1RHUU 6WRUHG2))6WDWH 67.)/75 (YDOXDWH 2SHQ/RDG LQ2))VWDWH 6WRUHG2))6WDWH! 67.)/75 6WRUHG2))6WDWH! 67.)/75! 2SHQORDG 6KRUWWR9FF *$3*&)7 DocID027886 Rev 7 55/100 93 Diagnostic VNQ7003SY Figure 21. Diagnostic flowchart for digital overload detection %FUBJMFEEJBHOPTJTJO0/TUBUF $IBOOFM'FFECBDLSFHJTUFS &WBMVBUF 1PXFSMJNJUBUJPO 0WFS-PBE 5FNQFSBUVSF4UBUVT &SSPSCJU T TFU /PFSSPS &OE $SJUJDBM 051-PO TJHOBMMFEDIBOOFM T 7%40WFS-PBEPO TJHOBMMFEDIBOOFM T JGOPUNBTLFECZ $0/'*(SFHJTUFS *$3*&)7 56/100 DocID027886 Rev 7 VNQ7003SY 6 Programmable blanking window Programmable blanking window Dedicated registers for each channel (CHLOFFTCR0,1 and CHLOFFTCR2,3) provide a variable and programmable blanking window in case of power limitation or overtemperature event. During this period, the corresponding channel is in auto-restart mode and the channel is allowed to stay in power-limitation and/or overtemperature state before latching off, once blanking time is expired, if the cause of the power limitation or overtemperature event is still present. In this case the channel latches off and the related flag in the latch-off error register (CHLOFFSR) is set. Latch-off flag is also reported in the Global Status Byte (see Section 4.3.1: Global Status byte description). If during the blanking time the cause of power limitation and/or overtemperature event disappears, the timer stops then the rest of the blanking time will be available for another power limitation and/or overtemperature event. Therefore it is up to MCU to reset the timer by refreshing the programmed value in the dedicated register (CHLOFFTCR0,1 or CHLOFFTCR2,3). MCU can keep the device in auto-restart forever artificially, by refreshing the programmed blanking time. 6.1 Timer The 4 bit value per channel written in CHLOFFTCRx register is translated internally into an 8 bit value. The four MSB of this 8 bit value correspond to the content of CHLOFFTCRx register, while the four LSB are filled with 0xF. The 8 bit value refers to an analogue timer value. Figure 22. Internal timer process The granularity of the 8-bit counter is tSTEP. At each power limitation or overtemperature event, the 8-bit counter is decreased by the number of steps equal to the duration of power limitation or overtemperature event. If power limitation or overtemperature phase lasts for less than tSTEP the counter is decreased by one step. After each downcount of the 8-bit register, the 4 MSB bits will be transferred to the 4 bits of corresponding CHLOFFTCRx register in order to refresh this register to the new value of the timer. The microcontroller can read only the 4 MSB bits content of the register. In consequence, the microcontroller can detect a change of every 16 steps of downcounting. Downcounting is stopped and the content of the 8-bit counter is frozen, when the channel is commanded off through Direct Input or SOCR register or when the channel goes into Fail Safe mode. 6.2 Blanking window values Typical values of the configurable blanking window are shown in Table 51: Time values written by MCU and their real value in timer register. DocID027886 Rev 7 57/100 93 Programmable blanking window VNQ7003SY Table 51. Time values written by MCU and their real value in timer register Bit 7 or bit 3 Bit 6 or bit 2 Bit 5 or bit 1 Bit 4 or bit 0 0xm 0xmF Typical value of blanking time 0 0 0 0 0x0 0xF Latch-OFF (ZERO) 0 0 0 1 0x1 0x1F 17 ms 0 0 1 0 0x2 0x2F 34 ms 0 0 1 1 0x3 0x3F 51 ms .... 0x4 0x4F 68 ms .... ... ... ... 1 1 1 0 0xE 0xEF 238 ms 1 1 1 1 0xF 0xFF 255 ms A peculiarity exists for the value 0x0. It configures the channel in Latch-OFF mode without blanking time. Consequently the channel will latch-off upon the first occurrence of power limitation or overtemperature event. 6.3 Limp Home mode In Limp Home mode, the device is in unlimited auto-restart operation. The blanking time window has no effect on the duration of the auto-restart. 6.4 Registers For more details refer to the SPI register and Diagnostics. Address 08h - Channel Latch OFF Timer Control Register (CHLOFFTCR0,1) Address 09h - Channel Latch OFF Timer Control Register (CHLOFFTCR2,3) 8 bit registers (Latch-OFF timer: R/W) are used for channel behavior configuration and the timer value setting. For each channel 4 bits are used. The value is written by MCU from 0x0 to 0xF. Latch-Off timer register access Write command - store new value, read-back (during write command) old value equal to the TIMER down-counting. - Any write command will clear the Flag in the Latch-OFF-Flag register and reset the timer. - This function will be used by MCU to clear the flag in the Latch-OFF-Flag register, which is READ only register. Read command - reads currently down-counted TIMER value. If channel was latched because of timer expired, channel is kept latched after read command. Address 32h - Channels latch-off status register - CHLOFFSR Each channel has one flag. Unused channels or not existent one is reserved bit. In case of latch-OFF of a channel, this flag will be set and readable by MCU. 58/100 DocID027886 Rev 7 VNQ7003SY Programmable blanking window Example 2: Figure 23. VNQ7003SY CHLOFFSR Latch-OFF Flag register access Write command - not allowed (status register) Read command - reads current status of channels; this has no impact on latched / un-latched channels. Clear command - not allowed. To clear this register, a write operation in the corresponding bit of CHLOFFTCR is required. DocID027886 Rev 7 59/100 93 Electrical specifications VNQ7003SY 7 Electrical specifications 7.1 Absolute maximum ratings Stressing the device above the rating listed in the Table 52: Absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 52. Absolute maximum ratings Symbol Parameter Value Unit VREG DC SPI supply stabilization 3.6 V -VREG Reverse DC SPI supply stabilization -0.3 V VCCJS Maximum jump start voltage for single pulse short circuit protection 28 V VCC DC supply voltage 38 V -VCC Reverse DC supply voltage (without external components) -0.3 V Internally limited A 9 A 20 +10/-1 A mA IOUT0,1,2,3 -IOUT0,1 -IOUT2,3 ISENSE Maximum DC output current Reverse DC output current DC CurrentSense input current EMAX0,1 Maximum switching energy (single pulse) TDEMAG = 0.1 ms; Tjstart = 150C 12.5 mJ EMAX2,3 Maximum switching energy (single pulse) TDEMAG = 0.1 ms; Tjstart = 150C 39.6 mJ VDD + 0.3 V -0.3 V +10/-1 mA 7 V -0.3 V +1/-1 mA +1/-1 mA 2000 2000 2000 2000 2000 2000 4000 4000 V VSDO DC SPI pin voltage -VSDO Reverse DC SPI pin voltage ISDI,CSN,SCK DC SPI pin current VDD DC Digital Control supply -VDD Reverse DC Digital Control supply IDIN0,1 DC direct input current IDIN2,3 ESD 60/100 Electrostatic discharge (ANSI-ESDA-JEDEC-JS-001-2014) - IN0,1,2,3 - VDD - VREG - CSN, SDI, SCK - SDO - CurrentSense - OUT0,1,2,3 DocID027886 Rev 7 VNQ7003SY Electrical specifications Table 52. Absolute maximum ratings Symbol Value Unit Junction operating temperature -40 to 150 C TSTG Storage temperature -55 to 150 C ILAT Latch up current 20 mA Tj 7.2 Parameter Thermal data Table 53. Thermal data Symbol Parameter Rthj-board Thermal resistance junction-board (JEDEC JESD 51-8) Rthj-amb Thermal resistance junction-ambient 7.3 Typ. value 3.8 See Figure 31 Unit C/W SPI electrical characteristics Mode 1: 4.5 V < VDD < 5.5 V, VDD and VREG independent; -40 C < Tj < 150 C, unless otherwise specified. Mode 2: 2.7 V < VDD < 3.3 V, VDD and VREG short circuited; -40 C < Tj < 150 C, unless otherwise specified. Table 54. DC characteristics - Mode 1 Symbol Parameter Test conditions Min. Typ. Max. Unit VDD_POR_ON Power-on reset threshold. Device leaves the Reset mode. Supply of digital part is reset. VDD increasing; VCC > VUSD 2.3 2.8 V VDD_POR_OFF Power-on shutdown threshold. Device enters Reset mode. Supply of digital part in shutdown. VDD decreasing; VCC > VUSD VPOR_HYST Power-on reset hysteresis IDD Digital part supply current in normal mode (@ Vdd = 5 V) VDD = 5 V; SPI active without frame communication 0.6 1.0 mA IDDstd Digital part supply current in standby state (@ Vdd = 5 V) VDD = 5 V; Tj = 125 C, INx = 0 V 5 20 A IIL Low level Input current VSDI,SCK = 0.3 VDD IIH High level Input current VSDI,SCK = 0.7 VDD VIL Input low voltage VIH Input high voltage VI_HYST Input hysteresis voltage VDD pin 1.4 2.0 V 0.5 V SDI, SCK pins 1 A 0.7VDD A 0.3VDD V V 1.0 DocID027886 Rev 7 10 V 61/100 93 Electrical specifications VNQ7003SY Table 54. DC characteristics - Mode 1 (continued) Symbol VSDI_CL VSCK_CL Parameter SDI clamping voltage Test conditions Min. IIN = 1 mA 5.8 IIN = -1 mA IIN = 1 mA SCK clamping voltage Typ. Max. Unit 7.3 V -0.6 5.8 IIN = -1 mA V 7.3 -0.6 V V SDO pin VOL Output low voltage ISDO = -5 mA; CSN low; fault condition; no SCK VOH Output high voltage ISDO = 5 mA; CSN low; no fault condition; no SCK ILO Output leakage current VSDO = 0 V or 5 V, CSN high; -40 C < Tj < 85 C -5 IIL_CSN Low level Input current VCSN = 0.3 VDD -10 IIH_CSN High level Input current VCSN = 0.7 VDD VIL_CSN Output low voltage VIH_CSN Output high voltage VHYST_CSN Input hysteresis voltage 0.2VDD 0.8VDD V V 5 A CSN pin VCL_CSN -1 A 0.3VDD V 0.7VDD V 1.0 IIN = 1 mA CSN clamping voltage 5.8 IIN = -1 mA VSCK_CL A SCK clamping voltage IIN = 1 mA V 7.3 -0.6 5.8 V V 7.3 V Typ. Max. Unit 2.3 2.8 V Table 55. DC characteristics - Mode 2 Symbol Parameter Test conditions Min. VDD pin VDD_POR_ON Power-on reset threshold. Device leaves the Reset mode. VDD increasing; VCC > VUSD Supply of digital part is reset. VDD_POR_OFF Power-on shutdown threshold. Device enters Reset mode. Supply of digital part in shutdown. VPOR_HYST Power-on reset hysteresis IDD Digital part supply current in normal mode (@ Vdd = 3 V) 62/100 VDD decreasing; VCC > VUSD VDD = 3 V; SPI active without frame communication DocID027886 Rev 7 1.4 2.0 V 0.3 V 0.3 0.5 mA VNQ7003SY Electrical specifications Table 55. DC characteristics - Mode 2 (continued) Symbol Parameter Test conditions IDDstd Digital part supply current in standby state (@ Vdd = 3 V) VDD = 3 V; Tj = 125 C, INx = 0 V IIL Low level Input current VSDI,SCK = 0.3 VDD IIH High level Input current VSDI,SCK = 0.7 VDD VIL Input low voltage VIH Input high voltage VI_HYST Input hysteresis voltage VSDI_CL SDI clamping voltage Min. Typ. Max. Unit 2 10 A SDI, SCK pins 1 10 A 0.3VDD V 0.7VDD V 0.8 IIN = 1 mA 5.8 IIN = -1 mA VSDK_CL A IIN = 1 mA SCK clamping voltage V 7.3 -0.6 5.8 IIN = -1 mA V V 7.3 -0.6 V V SDO pin VOL Output low voltage ISDO = -5 mA; CSN low; fault condition; no SCK VOH Output high voltage ISDO = 5 mA; CSN low; no fault condition; no SCK 0.8VDD ILO Output leakage current VSDO = 0 V or VDD, CSN high; -40 C < Tj < 85 C -5 IIL_CSN Low level Input current VCSN = 0.3 VDD -10 IIH_CSN High level Input current VCSN = 0.7 VDD VIL_CSN Output low voltage VIH_CSN Output high voltage VHYST_CSN Input hysteresis voltage VCL_CSN CSN clamping voltage 0.2VDD V V 5 A CSN pin A -1 A 0.3VDD V 0.7VDD V 0.8 IIN = 1 mA 5.8 IIN = -1 mA V 7.3 -0.6 V V Table 56. AC characteristics (SDI, SCK, CSN, SDO pins) - Mode 1 Symbol Parameter Test conditions Min. Typ. Max. Unit COUT Output capacitance (SDO) VOUT = 0 V to 5 V -- -- 10 pF Input capacitance (SDI) VIN = 0 V to 5 V -- -- 10 pF Input capacitance (other pins) VIN = 0 V to 5 V -- -- 10 pF CIN DocID027886 Rev 7 63/100 93 Electrical specifications VNQ7003SY Table 57. AC characteristics (SDI, SCK, CSN, SDO pins) - Mode 2 Symbol Parameter Test conditions Min. Typ. Max. Unit COUT Output capacitance (SDO) VOUT = 0 V to 3 V -- -- 10 pF Input capacitance (SDI) VIN = 0 V to 3 V -- -- 10 pF Input capacitance (other pins) VIN = 0 V to 3 V -- -- 10 pF Max. Unit 4 MHz CIN Table 58. Dynamic characteristics - Mode 1 Symbol fC Parameter Test conditions Clock frequency Min. Typ. Duty cycle = 50% tWHCH CSN timeout: time to release SDO bus 30 70 ms tWDTB Watchdog toggle bit timeout 30 70 ms tSLCH CSN low setup time 120 ns tSHCH CSN high setup time 1200 ns tDVCH Data in setup time 20 ns tCHDX Data in hold time 30 ns tCH Clock high time 115 ns tCL Clock low time 115 ns tCLQV Clock low to output valid COUT = 1 nF 150 ns tQLQH Output rise time COUT = 1 nF 110 ns tQHQL Output fall time COUT = 1 nF 110 ns tWU tstdby_out tSCLK Rising edge of VDD to first allowed communication 3 Minimum time during which CSN must be toggled low to go out of STDBY mode 30 SCK setup time before CSN rising 150 80 23 s 150 s ns tCSNQV CSN low to output valid 50 100 ns tCSNQT CSN high to output tristate 50 100 ns Max. Unit 4 MHz Table 59. Dynamic characteristics - Mode 2 Symbol fC Parameter Test conditions Clock frequency Min. Duty cycle = 50% Typ. tWHCH CSN timeout: time to release SDO bus 30 70 ms tWDTB Watchdog toggle bit timeout 30 70 ms tSLCH CSN low setup time 120 ns tSHCH CSN high setup time 1200 ns tDVCH Data in setup time 20 ns 64/100 DocID027886 Rev 7 VNQ7003SY Electrical specifications Table 59. Dynamic characteristics - Mode 2 (continued) Symbol tCHDX Parameter Test conditions Min. Typ. Max. Unit Data in hold time 30 ns tCH Clock high time 115 ns tCL Clock low time 115 ns tCLQV Clock low to output valid COUT = 1 nF 150 ns tQLQH Output rise time COUT = 1 nF 110 ns tQHQL Output fall time COUT = 1 nF 110 ns tWU tstdby_out tSCLK Rising edge of VDD to first allowed communication 3 Minimum time during which CSN must be toggled low to go out of STDBY mode 30 SCK setup time before CSN rising 150 80 23 s 150 s ns tCSNQV CSN low to output valid 50 100 ns tCSNQT CSN high to output tristate 50 100 ns Figure 24. SPI dynamic characteristics W6+&+ &61 W&6149 W&6147 6'2 'DWDRXW 'DWDRXW W&/49 W6&/. W6/&+ 6&. W'9&+ 6', W&+ W&/ 'DWDLQ 'DWDLQ W4/4+ 6'2 ORZWRKLJK 9&& 9&& W4+4/ 9&& 6'2 KLJKWRORZ 9&& WILQ WULQ 9&& 6&. 9&& ("1($'5 DocID027886 Rev 7 65/100 93 Electrical specifications VNQ7003SY Table 60. VREG pin - Mode 1 Symbol VREG ZREG IREG_Max 7.4 Parameter Test conditions Min. Typ. Max. Unit Supply voltage in normal mode VDD = 5 V; normal mode 2.5 3 3.5 V Supply voltage in standby Output impedance VDD = 5 V; standby mode 2.5 3 3.5 V VDD = 5 V; IREG = 5 mA 50 Maximum output current VREG = 90% * VREG(typ); VDD = 5 V 7 mA Electrical characteristics 7 V < VCC < 28 V; -40 C < Tj < 150 C, unless otherwise specified. Table 61. Power section Symbol Parameter Test conditions Min. Typ. Max. Unit 4 13 28 V Undervoltage shutdown 3 4 V Undervoltage shutdown hysteresis 0.25 VCC Operating supply voltage VUSD VUSDhyst Vclamp Istby Is(on) IL(off) VF0,1 VF2,3 VCC clamp voltage ICC = 20 mA; IOUT0,1,2,3 = 0 A 38 46 52 V 0.1 2 A 5 10 A 8.5 14 mA 0.1 0.5 A 3 A VCC = 13 V; IOUT = 3 A; Tj = 150 C 0.7 V VCC = 13 V; IOUT = 6 A; Tj = 150 C 0.7 V Sleep mode1; VCC = 13 V; Tj = 25 Supply current in sleep mode at C; VDD = 0 V VCC = 13 V; Tj = 25C Sleep mode2; VCC = 13 V; Tj = 25 C; VDD = 5 V Supply current in ON-state ON-state (all channels ON); VCC = 13 V; VDD = 5 V; IOUT = 0 A OFF state output current at VCC VDD = 0 V; VCC = 13 V; = 13 V, Tj = 25C Tj = 25 C; Vin = Vout = 0 V 0 OFF-state output current at VCC VDD = 0 V; VCC = 13 V; = 13 V, Tj = 125C Tj = 125 C; Vin = Vout = 0 V 0 Output VCC diode voltage at Tj = 150C V Table 62. Logic inputs (IN0,1,2,3 pins) Symbol Parameter VIL0,1,2,3 Input low level voltage IIL0,1,2,3 Low level input current VIH0,1,2,3 Input high level voltage IIH0,1,2,3 High level input current 66/100 Test conditions VIN = 0.9 V VIN = 2.1 V DocID027886 Rev 7 Min. Typ. Max. Unit 0.9 V 1 A 2.1 V 10 A VNQ7003SY Electrical specifications Table 62. Logic inputs (IN0,1,2,3 pins) (continued) Symbol Parameter VI(hyst)0,1,2,3 Input hysteresis voltage VICL2,3 Input clamp voltage Test conditions Min. IIN = 1 mA Input clamp voltage Max. Unit IIN = 1 mA V 5.5 IIN = -1 mA VICL0,1 Typ. 0.2 7.5 V -0.7 5.5 IIN = -1 mA V 8.2 V -0.7 V Table 63. Protection Symbol Parameter Test conditions Min. Typ. Max. Uni Junction-case temperature DTPLIM(1) difference triggering power limitation protection VCC = 13 V 60 C Junction-case temperature difference resetting power limitation protection VCC = 13 V 35 C Shutdown temperature VCC = 13 V 150 175 TRS + 5 DTPLIMR TTSD TR Reset temperature VCC = 13 V, latched off mode disabled TRS + 1 TRS Thermal reset of CHFBSR fault detection VCC = 13 V, latched off mode disabled 135 THYST Thermal hysteresis (TTSD - TR) VCC = 13 V, latched off mode disabled TCSD(2) Case thermal detection prewarning VCC = 13 V (see Table 31: CTLR -- Control Register) TCR (2) Case thermal detection reset VCC = 13 V VDS_OVL VDS overload detection threshold tBlanking Programmable blanking time tON_MIN Minimum turn-on time per channel to avoid false VDS error flag at VCC = 13 V 200 C C 10 TCSD nom-15 TCSD nom C TCSD nom+15 TCSD nom-15 VCC - 1.5 C C VCC - 0.5 V 20 % Bulb mode, ch0 and ch1 220 s LED mode, ch0 and ch1 150 s Bulb mode, ch2 and ch3 220 s -20 VCC - 1.0 C 1. Zthj-case x P = TPLIM, Zth-case is the thermal impedance, P is the Power. 2. Guarantee by Design and Characterization. DocID027886 Rev 7 67/100 93 Electrical specifications VNQ7003SY Table 64. Open-load detection (7V < VCC < 18 V) Symbol Parameter Test conditions Min. Typ. Max. Unit VOL Open-load OFF-state voltage detection threshold CHx off VCC1.5 VCC - 1.0 VCC - 0.5 V IPU Pull-up current generator for open-load at OFF-state detection Pull-up current generator active, Vout = VCC - 1.0 V -1.4 -0.75 -0.4 mA tDOLOFF Delay time after turn off to allow open-load OFF-state detection 0.25 0.75 1.25 ms Max. Unit 7.4.1 BULB mode Table 65. BULB - power section Symbol RON_ch0,1 RON_ch2,3 Parameter ON-state resistance ON-state resistance Test conditions Min. Typ. IOUT = 3 A; Tj = 25 C -- 25 IOUT = 3 A; Tj = 150 C -- 50 m IOUT = 3 A; VCC = 4 V; Tj = 25 C -- 37.5 m IOUT = 6 A; Tj = 25 C -- IOUT = 6 A; Tj = 150 C -- 14 m IOUT = 6 A; VCC = 4 V; Tj = 25 C -- 10.5 m m 7 m Table 66. BULB - switching (VCC = 13 V; Normal switch mode) Symbol tdon tdoff Min. Typ. Max. Unit From 50% CSN to 20% VOUT; RL = 4.3 25 70 115 s Turn-on delay time Ch2,3 From 50% CSN to 20% VOUT; RL = 2.2 50 100 150 s Turn-off delay time Ch0,1 From 50% CSN to 80% VOUT; RL = 4.3 30 45 60 s Turn-off delay time Ch2,3 From 50% CSN to 80% VOUT; RL = 2.2 40 60 80 s Turn-off turn-on time Ch0,1 From 50% CSN to 50% VOUT; RL = 4.3 -60 40 s Turn-off turn-on time Ch2,3 From 50% CSN to 50% VOUT; RL = 2.2 -85 15 s Turn-on voltage slope Ch0,1 VOUT = 2.6 V to 10.4 V; RL = 4.3 0.05 0.3 0.7 V/s Turn-on voltage slope Ch2,3 VOUT = 2.6 V to 10.4 V; RL = 2.2 ; normal switch mode 0.05 0.2 0.7 V/s (1) (dVOUT/dt)on(1) Test conditions Turn-on delay time Ch0,1 (1) tskew(1) 68/100 Parameter DocID027886 Rev 7 VNQ7003SY Electrical specifications Table 66. BULB - switching (VCC = 13 V; Normal switch mode) (continued) Symbol Parameter Test conditions Min. Typ. Max. Unit Turn-off voltage slope Ch0,1 VOUT = 10.4 V to 2.6 V; RL = 4.3 ; normal switch mode 0.05 0.3 0.7 V/s Turn-off voltage slope Ch2,3 from VOUT = 10.4 V to 2.6 V; RL = 2.2 ; normal switch mode 0.05 0.2 0.7 V/s Switching losses energy at turn-on Ch0,1 RL = 4.3 0.3 1(2) Switching losses energy at turn-on Ch2,3 RL = 2.2 0.9 2(2) Switching losses energy at turn-off Ch0,1 RL = 4.3 0.3 1(2) Switching losses energy at turn-off Ch2,3 RL = 2.2 0.9 2(2) Min. Typ. Max. Unit (dVOUT/dt)off(1) WON WOFF 1. See Figure 26: Switching characteristics. 2. Parameter guaranteed by design and characterization; not subject to production test. Table 67. BULB - switching (VCC = 13 V; Fast switch mode) Symbol tdon(1) tdoff (1) tskew(1) (dVOUT/dt)on(1) (dVOUT/dt)off(1) Parameter Test conditions Turn-on delay time Ch0,1 From 50% CSN to 20% VOUT; RL = 4.3 25 70 115 s Turn-on delay time Ch2,3 From 50% CSN to 20% 50 100 150 s Turn-off delay time Ch0,1 From 50% CSN to 80% VOUT; RL = 4.3 20 30 40 s Turn-off delay time Ch2,3 From 50% CSN to 80% 30 45 60 s Turn-off turn-on time Ch0,1 From 50% CSN to 50% VOUT; RL = 4.3 -75 25 s Turn-off turn-on time Ch2,3 From 50% CSN to 50% -110 -10 s Turn-on voltage slope Ch0,1 VOUT = 2.6 V to 10.4 V; RL = 4.3 0.05 0.4 0.9 V/s Turn-on voltage slope Ch2,3 VOUT = 2.6 V to 10.4 V; 0.05 0.3 0.7 V/s Turn-off voltage slope Ch0,1 VOUT = 10.4 V to 2.6 V; RL = 4.3 0.05 0.4 0.9 V/s Turn-off voltage slope Ch2,3 from VOUT = 10.4 V to 0.05 0.35 0.7 V/s DocID027886 Rev 7 69/100 93 Electrical specifications VNQ7003SY Table 67. BULB - switching (VCC = 13 V; Fast switch mode) (continued) Symbol WON WOFF Parameter Test conditions Min. Typ. Max. Unit Switching losses energy at turn-on Ch0,1 RL = 4.3 0.2 1(2) mJ Switching losses energy at turn-on Ch2, 3 RL = 2.2 0.8 2(2) mJ Switching losses energy at turn-off Ch0,1 RL = 4.3 0.2 1(2) mJ Switching losses energy at turn-off Ch2,3 RL = 2.2 0.6 2(2) mJ 1. See Figure 26: Switching characteristics. 2. Parameter guaranteed by design and characterization; not subject to production test. Table 68. BULB - protection and diagnostic Symbol IlimH_ch0,1 IlimL_ch0,1 IlimH_ch2,3 IlimL_ch2,3 VDEMAG Parameter Test conditions Short circuit current at VCC= 13 V VCC = 13 V, VDD = 0 V, VIN0,1 = 5 V Short circuit current at 5 V< VCC < 18 V(1) Short circuit current during thermal cycling Vin0,1 = 5 V VCC = 13 V, VDD = 0 V, VIN0,1 = 5 V, TR < Tj < TTSD Short circuit current at VCC= 13 V VCC = 13 V, VDD = 0 V, VIN2,3 = 5 V Short circuit current at 5 V < VCC < 18 V(1) Short circuit current during thermal cycling Vin2,3 = 5 V Min. Typ. Max. Unit 25 35 50 A 50 A 11.5 55 VCC = 13 V, VDD = 0 V, VIN2,3 = 5 V, TR < Tj < TTSD Turn-off output voltage clamp; IOUT = 2 A; VIN0,1,2,3 = 0 V; 25 C < Tj < 150 C L = 6 mH A 80 110 A 110 A 26.5 VCC-40 A VCC-44 VCC-48 V 1. Parameter guaranteed by design and characterization; not subjected to production test. Table 69. BULB - CurrentSense (7 V < VCC < 18 V, channel 0,1; Tj = -40 C to 150 C) Symbol K1 dK1/K(1) (2) K2 dK2/K(1) (2) K3 70/100 Parameter Test conditions Min. Typ. Max. Unit IOUT/ISENSE IOUT = 0.4 A; VSENSE = 0.5 V -30% 3700 30% CurrentSense ratio drift IOUT = 0.4 A; VSENSE = 0.5 V -20 IOUT/ISENSE IOUT = 2 A; VSENSE = 4 V -15% CurrentSense ratio drift IOUT = 2 A; VSENSE = 4 V -10 IOUT/ISENSE IOUT = 6 A; VSENSE = 4 V -10% DocID027886 Rev 7 20 3700 15% 10 3700 % 10% % VNQ7003SY Electrical specifications Table 69. BULB - CurrentSense (7 V < VCC < 18 V, channel 0,1; Tj = -40 C to 150 C) (continued) Symbol dK3/K(1) (2) ISENSE0 Parameter CurrentSense ratio drift Analog sense current Test conditions tDSENSE1L(3) tDSENSE2H (3) tDSENSE2L (3) tD_XtoY Typ. Max. Unit IOUT = 6 A; VSENSE = 4 V -8 8 % CurrentSense disabled; VSENSE = 0 V; IOUTx = 0 A All channels are OFF 0 1 A Current Sense Enabled; VSENSE = 0 V; IOUTx = 0 A; Vinx = 5 V; others Channels ON in Bulb Mode at their load nominal current e.g. Ch0: VIN0 = 5 V; VIN1,2,3 = 5 V; IOUT0 = 0 A; IOUT1 = 2 A; IOUT2,3 = 6 A 0 15 A -0.5 0.5 A 150 400 s 50 250 s 20 40 s 5 20 s 100 s CurrentSense disabled; VINx = 5 V -1 V < VSENSE < 5 V(2) tDSENSE1H (3) Min. Normal switch mode; VSENSE < 4 V, Delay response time from RSENSE = 2 k; rising edge of CSN pin ISENSE = 90% of ISENSEmax (turn-on of the channel) (see Figure 25: CurrentSense delay characteristics) Normal switch m)ode; VSENSE < 4 V, Delay response time from RSENSE = 2 k; rising edge of CSN pin ISENSE = 10 % of ISENSEmax (turn-off of the channel) (see Figure 25: CurrentSense delay characteristics) Delay response time from Bit3 of CSMUXCR register (MUXEN) CurrentSense MUX from 0 to 1; RSENSE = 2 k ; RL = 4.3 enable Delay response time from Bit3 of CSMUXCR register (MUXEN) CurrentSense MUX from 1 to 0; Rsense = 2 k; RL = 4.3 disable CurrentSense transition delay from ChX to ChY ISENSE = 1 mA 8 9 10 V ISENSE = -1 mA -10 -9 -8 V CurrentSense saturation voltage VCC = 7 V; RSENSE = 2.7 k; VIN0,1 = 5 V; IOUT0,1 = 12 A; Tj = -40C 4.8 V ISENSE_SAT (2) CurrentSense saturation current VCC = 7 V; VSENSE = 4 V; VIN0,1 = 5 V; Tj = 150C 4 mA IOUT_SAT_B (2) Output saturation current in BULB mode VCC = 7 V; VSENSE = 4 V; VIN0,1 = 5 V; Tj = 150C 15 A VSENSE_CL CurrentSense clamp voltage VSENSE_SAT 1. All values refer to VCC = 13 V; Tj = 25C, unless otherwise specified. 2. Parameter guaranteed by design and characterization; not subjected to production test. DocID027886 Rev 7 71/100 93 Electrical specifications VNQ7003SY 3. Transition delays are measured up to 10% of final conditions. Table 70. BULB - CurrentSense (7 V < VCC < 18 V, channel 2,3; Tj = -40 C to 150 C) Symbol K1 dK1/K(1) (2) K2 dK2/K2 (1) (2) K3 dK3/K3(1) (2) ISENSE0 Parameter IOUT/ISENSE Test conditions IOUT = 450 mA; VSENSE = 0.5 V CurrentSense ratio drift IOUT = 450 mA; VSENSE = 0.5 V IOUT/ISENSE IOUT = 6 A; VSENSE = 4 V CurrentSense ratio drift IOUT = 6 A; VSENSE = 4 V IOUT/ISENSE IOUT = 18 A; VSENSE = 4 V CurrentSense ratio drift IOUT = 18 A; VSENSE = 4 V Analog sense current CurrentSense disabled; VSENSE = 0 V; IOUTx = 0 A; All channels are OFF Current Sense Enabled; VSENSE = 0 V; IOUTx = 0 A; VINx = 5 V; other channels ON in Bulb Mode at their load nominal current e.g. Ch2: VIN2 = 5 V; VIN0,1,3 = 5 V; IOUT2 = 0 A; IOUT0,1 = 2 A; IOUT3 = 6 A CurrentSense disabled; VINx = 5 V; - 1 V < VSENSE < 5 V (2) Min. Typ. Max. -50% 10100 50% -30 -11% 30 10100 -9 -10% % 11% 9 10100 Unit % 10% -8 8 % 0 1 A 0 15 A -0.5 0.5 A tDSENSE1H(3) Normal switch mode; VSENSE < 4 V, Delay response time RSENSE = 2 k; ISENSE = 90 % of from rising edge of CSN ISENSEmax pin (turn-on of the (see Figure 25: CurrentSense channel) delay characteristics) 250 400 s tDSENSE1L (3) Normal switch mode; Delay response time VSENSE < 4 V, RSENSE = 2 k;; ISENSE from rising edge of CSN = 10 % of ISENSEmax pin (turn-off of the (see Figure 25: CurrentSense channel) delay characteristics) 50 250 s tDSENSE2 (3) Delay response time from CurrentSense MUX enable Bit3 of CSMUXCR register (MUXEN) from 0 to 1; RSENSE = 2 k; RL = 2.2 20 100 s tDSENSE2L(3) Delay response time from CurrentSense MUX disable Bit3 of CSMUXCR register (MUXEN) from 1 to 0; RSENSE = 2 k; RL = 2.2 5 20 s 72/100 DocID027886 Rev 7 VNQ7003SY Electrical specifications Table 70. BULB - CurrentSense (7 V < VCC < 18 V, channel 2,3; Tj = -40 C to 150 C) (continued) Symbol Parameter Test conditions tD_XtoY CurrentSense transition delay from ChX to ChY Min. Typ. Max. Unit 100 s VSENSE_CL CurrentSense clamp voltage ISENSE = 1 mA 8 9 10 V ISENSE = -1 mA -10 -9 -8 V VSENSE_SAT CurrentSense saturation voltage VCC = 7 V; RSENSE = 2.7 k; VIN2,3 = 5 V; IOUT2,3 = 36 A; Tj = -40C 4.8 V ISENSE_SAT(2) CurrentSense saturation current VCC = 7 V; VSENSE = 4 V; VIN2,3 = 5 V; Tj = 150C 4 mA Output saturation current in BULB mode VCC = 7 V; VSENSE = 4 V; VIN2,3 = 5 V; Tj = 150C 42 A IOUT_SAT_BULB (2) 1. All values refer to VCC = 13 V; Tj = 25C, unless otherwise specified. 2. Parameter guaranteed by design and characterization; not subjected to production test. 3. Transition delays are measured up to 10% of final conditions. 7.4.2 LED mode (Channel 0, 1) 7 V < VCC < 18 V; -40 C < Tj < 150 C, unless otherwise specified. Table 71. LED - power section Symbol RON Ch0,1 Parameter ON-state resistance Test conditions Min. Typ. Max. Unit IOUT = 1.3 A; Tj = 25 C -- 60 IOUT = 1.3 A; Tj = 150 C -- 120 m IOUT = 1.3 A; VCC = 4 V; Tj = 25 C -- 90 m m Table 72. LED - switching (VCC = 13 V; Normal switch mode) Symbol Parameter Test conditions Min. Typ. Max. Unit tdon (1) Turn-on delay time From 50% CSN to 20% VOUT RL = 13 20 60 100 s tdoff (1) Turn-off delay time From 50% CSN to 80% VOUT RL = 13 25 40 55 s tskew (1) Turn-off, turn-on time From 50% CSN to 50% VOUT; RL = 13 -60 40 s (dVOUT/dt)(1) Turn-on voltage slope VOUT = 2.6 V to 10.4 V RL = 13 0.05 0.2 0.7 V/s From VOUT = 10.4 V to 2.6 V RL = 13 0.05 0.3 0.7 V/s (dVOUT/dt)off(1) Turn-off voltage slope WON Switching losses energy at turn-on RL = 13 0.1 1(2) mJ WOFF Switching losses energy at turn-off RL = 13 0.1 1(2) mJ DocID027886 Rev 7 73/100 93 Electrical specifications VNQ7003SY 1. See Figure 26: Switching characteristics. 2. Parameter guaranteed by design and characterization; not subjected to production test. Table 73. LED - switching (VCC = 13 V; Fast switch mode) Symbol Parameter Test conditions Min. Typ. Max. Unit tdon(1) Turn-on delay time From 50% CSN to 20% VOUT RL = 13 20 60 100 s tdoff (1) Turn-off delay time From 50% CSN to 80% VOUT RL = 13 15 25 35 s tskew(1) Turn-off, turn-on time From 50% CSN to 50% VOUT RL = 13 -70 30 s (dVOUT/dt)on (1) Turn-on voltage slope VOUT = 2.6 V to 10.4 V RL = 13 0.05 0.6 1 V/s (dVOUT/dt)off(1) Turn-off voltage slope From VOUT = 10.4 V to 2.6 V RL = 13 0.05 0.6 1 V/s WON Switching losses energy at turn-on RL = 13 0.06 1(2) mJ WOFF Switching losses energy at turn-off RL = 13 0.06 1(2) mJ 1. See Figure 26: Switching characteristics. 2. Parameter guaranteed by design and characterization; not subjected to production test. Table 74. LED - protection and diagnosis Symbol IlimH_ch0,1 IlimL_ch0,1 Parameter Short circuit current at VCC = 13 V Short circuit current at 5V< VCC < 18 V(1) Short circuit current during thermal cycling Test conditions Min. Typ. Max Unit VCC = 13 V, VDD =0 V, VIN0,1 = 5 V 7 12 18 A 18 A Vin0,1 = 5 V VCC = 13 V, VDD = 0 V, VIN0,1 = 5 V, TR < Tj < TTSD 4 A 1. Parameter guaranteed by design and characterization; not subjected to production test. Table 75. LED - CurrentSense (7 V < VCC < 18 V; Tj = -40 C to 150 C) Symbol K0 dK0/K0(1) (2) K1 dK1/K (1) (2) K2 74/100 Parameter Test conditions Min. Typ. Max. 1400 60% IOUT/ISENSE IOUT = 10 mA; VSENSE= 0.5 V -60% CurrentSense ratio drift IOUT = 10 mA; VSENSE = 0.5 V -50 IOUT/ISENSE IOUT = 50 mA; VSENSE = 0.5 V -50% CurrentSense ratio drift IOUT = 50 mA; VSENSE = 0.5 V -30 IOUT/ISENSE IOUT = 0.3 A VSENSE = 4 V DocID027886 Rev 7 -20% 50 1400 % 50% 30 1400 Unit 20% % VNQ7003SY Electrical specifications Table 75. LED - CurrentSense (7 V < VCC < 18 V; Tj = -40 C to 150 C) (continued) Symbol dK2/K2(1) (2) Parameter CurrentSense ratio drift Test conditions IOUT = 0.3 A; VSENSE = 4 V Current Sense disabled; VSENSE = 0 V; IOUTx = 0 A; All channels are OFF ISENSE0 Analog sense current Current Sense Enabled; VSENSE = 0 V; IOUTx = 0 A; VINx = 5 V; other channels ON in Bulb Mode at their load nominal current e.g. Ch0: VIN0 = 5 V; VIN1,2,3 = 5 V; IOUT0 = 0 A; IOUT1 = 2 A; IOUT2,3 = 6 A CurrentSense disabled; VINx = 5 V (2); Min. Typ. Max. Unit -13 13 % 0 1 A 0 10 A -0.5 0.5 A tDSENSE1H(3) Delay response time from rising edge of CSN pin (turn-on of the channel) VSENSE < 4 V, RSENSE = 2 k; ISENSE = 90 % of ISENSEmax (see Figure 25: CurrentSense delay characteristics) 150 250 s tDSENSE1L (3) Delay response time from rising edge of CSN pin (turn-off of the channel) VSENSE < 4 V, RSENSE = 2 k; ISENSE = 10 % of ISENSEmax (see Figure 25: CurrentSense delay characteristics) 50 120 s tDSENSE2H (3) Delay response time from CurrentSense MUX enable Bit3 of CSMUXCR register (MUXEN) from 0 to 1; RSENSE = 2 k; RL = 13 20 100 s Delay response time from CurrentSense CurrentSense transition delay from ChX to ChY Bit3 of CSMUXCR register (MUXEN) from 1 to 0; RSENSE = 2 k ; RL = 13 5 20 s 100 s VSENSE_CL CurrentSense clamp voltage ISENSE = 1 mA 8 9 10 V ISENSE = -1 mA -10 -9 -8 V VSENSE_SAT CurrentSense saturation voltage VCC = 7 V; RSENSE = 2.7 k; VIN0,1 = 5 V; IOUT0,1 = 4 A; Tj = 40C 4.8 V ISENSE_SAT(2) CurrentSense saturation current VCC = 7 V; VSENSE = 4 V; VIN0,1 = 5 V; Tj = 150C 4 mA Output saturation current in LED mode VCC = 7 V; VSENSE = 4 V; VIN0,1 = 5 V; Tj = 150C 6 A tDSENSE2L(3) tD_XtoY IOUT_SAT_LED(2) 1. All values refer to VCC = 13 V; Tj = 25C, unless otherwise specified. 2. Parameter guaranteed by design and characterization; not subjected to production test. 3. Transition delays are measured up to 10% of final conditions. DocID027886 Rev 7 75/100 93 Electrical specifications VNQ7003SY Figure 25. CurrentSense delay characteristics Figure 26. Switching characteristics 7XUQ 21SKDVH 62&55HJLVWHU 7XUQ 2))SKDVH 62&55HJLVWHU &61 9287[ G9287 GW2)) G9287 GW21 WG2)) WG21 WI WU WVNHZ WG2))WI WG21WU *$3*36 76/100 DocID027886 Rev 7 VNQ7003SY 8 ISO Pulse ISO Pulse The immunity of the device against transient electrical emissions, conducted along the supply lines and injected into the VCC pin, is tested in accordance with ISO7637-2:2011(E) and ISO 16750-2:2010. The related function performances status classification is shown in the Table 76: ISO 7637-2 - electrical transient conduction along supply line. Test pulses are applied directly to DUT (Device Under Test) both in ON and OFF-state and in accordance to ISO 7637-2:2011(E), chapter 4. The DUT is intended as the present device only, with external components as shown in Figure 27: M0-7 SPI Standard connection SPI only and Figure 28: M0-7 SPI standard, full connection. "Status II" is defined in ISO 7637-1 Function Performed Status Classification (FPSC) as follows: "The function does not perform as designed during the test but returns automatically to normal operation after the test". Table 76. ISO 7637-2 - electrical transient conduction along supply line Test Pulse 2011(E) Test pulse severity level with Status II functional performance status Minimum number of pulses or test time Burst cycle / pulse repetition time Pulse duration and pulse generator internal Impedance Level US (1) 1(2) III -112 V 500 pulses 0.5 s 5s 2 ms, 10 2a(3) IV +112 V 500 pulses 0.2 s 5s 50 s, 2 (2) IV -220 V 1h 90 ms 100 ms 0.1 s, 50 3b IV +150 V 1h 90 ms 100 ms 0.1 s, 50 4(4) IV -7 V 1 pulse 3a 100 ms, 0.01 Load dump according to ISO 16750-2:2010 Test B(3) 40 V 5 pulse 1 min 400 ms, 2 1. Us is the peak amplitude as defined for each test pulse in ISO 7637-2:2011(E), Chapter 5.6. 2. Device goes in reset state and must be reinitialized. 3. With 38V external suppressor referred to ground (-40 C < Tj < 150 C). 4. Test pulse in ISO 7637-2:2004(E). DocID027886 Rev 7 77/100 93 Application schematics 9 VNQ7003SY Application schematics Figure 27. M0-7 SPI Standard connection SPI only Table 77. Component values Reference Value RVDD 330 Device logic protection CVREG 100 nF Optional for EMI reduction- Low ESR, mount close to IC CVCC 100 nF Battery voltage spikes filtering mounted close to IC RCSN 2.7 k Microcontroller protection during overvoltage and reverse polarity RCLK 2.7 k Microcontroller protection during overvoltage and reverse polarity RSDI 2.7 k Microcontroller protection during overvoltage and reverse polarity RSDO 220 Microcontroller protection during overvoltage and reverse polarity Schottky (i.e. BAT54-Y) Microcontroller protection during overvoltage and reverse polarity D1 comment RPROT 15K Microcontroller protection during: overvoltage, reverse polarity and loss of GND RSENSE 1K Sensing resistor 78/100 DocID027886 Rev 7 VNQ7003SY Application schematics Table 77. Component values (continued) Reference Value Csense 470 pF comment D2 Suppressor 20 V Negative transient protection. D3 Suppressor 36 V Overvoltage protection. DGND BAS21 for VDD = 5V Schottky (i.e., BAT54-Y) for VDD = 3.3V Microcontroller ADC spikes filter Reverse polarity protection. Usage of schottky or standard diode dependent on VDD Figure 28. M0-7 SPI standard, full connection DocID027886 Rev 7 79/100 93 Package and PCB thermal data VNQ7003SY 10 Package and PCB thermal data 10.1 PowerSSO-36 thermal data Figure 29. PowerSSO-36 PC board 80/100 DocID027886 Rev 7 VNQ7003SY Package and PCB thermal data Table 78. PCB properties Dimension Value Board finish thickness 1.6 mm +/- 10% Board dimension 129 mm x 60 mm Board Material FR4 Copper thickness (top and bottom layers) 0.070 mm Copper thickness (inner layers) 0.035 mm Thermal vias separation 1.2 mm Thermal via diameter 0.3 mm +/- 0.08 mm Copper thickness on vias 0.025 mm Footprint dimension (top layer) 4.1 mm x 6.5 mm Heatsink copper area dimension (bottom layer) Footprint, 2 cm2 or 8 cm2 Figure 30. Rthj-amb vs PCB copper area in open box free air conditions DocID027886 Rev 7 81/100 93 Package and PCB thermal data VNQ7003SY Figure 31. PowerSSO-36 thermal impedance junction ambient single pulse 82/100 DocID027886 Rev 7 VNQ7003SY Package and PCB thermal data Equation 1 ZTH = RTH * + ZTHtp (1 - ) where = tP/T Figure 32. Thermal fitting model for PowerSSO-36 Note: The fitting model is a simplified thermal tool and is valid for transient evolutions where the embedded protections (power limitation or thermal cycling during thermal shutdown) are not triggered. Table 79. Thermal parameters Area/island (cm2) FP 2 8 4L R1 = R7 (C/W) 0.9 R2 = R8 (C/W) 2.5 R3 (C/W) 3.4 3.4 3.4 2.6 R4 (C/W) 6 6 6 3 R5 (C/W) 18 14 10 2 R6 (C/W) 30 26 15 7 R7 (C/W) 0.9 R8 (C/W) 2.5 R9 (C/W) 0.7 R10 (C/W) 1.6 DocID027886 Rev 7 83/100 93 Package and PCB thermal data VNQ7003SY Table 79. Thermal parameters (continued) Area/island (cm2) FP 2 8 4L R11 (C/W) 0.7 R12 (C/W) 1.6 C1 (W*s/C) 0.0007 C2 (W*s/C) 0.004 C3 (W*s/C) 0.1 C4 (W*s/C) 0.5 0.8 0.8 1 C5 (W*s/C) 1 2 3 10 C6 (W*s/C) 3 5 9 18 C7 (W*s/C) 0.0007 C8 (W*s/C) 0.004 C9 (W*s/C) 0.0009 C10 (W*s/C) 0.008 C11 (W*s/C) 0.0009 C12 (W*s/C) 0.008 84/100 DocID027886 Rev 7 VNQ7003SY 11 Maximum demagnetization energy (VCC = 16 V) Maximum demagnetization energy (VCC = 16 V) Figure 33. Maximum turn off current versus inductance - Channel 0,1 Figure 34. Maximum turn off current versus inductance - Channel 2,3 DocID027886 Rev 7 85/100 93 Maximum demagnetization energy (VCC = 16 V) Note: 86/100 VNQ7003SY Values are generated with RL = 0 . In case of repetitive pulses, Tjstart (at the beginning of each demagnetization) of every pulse must not exceed the temperature specified above for curves A and B. DocID027886 Rev 7 VNQ7003SY 12 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. 12.1 PowerSSO-36 package information Figure 35. PowerSSO-36 package outline %277209,(: 7239,(: 6(&7,21 $$ 6(&7,21%% *$3*&) 7 DocID027886 Rev 7 87/100 93 Package information VNQ7003SY Table 80. PowerSSO-36 mechanical data Dimensions Ref. Millimeters Min. Typ. 0 8 1 5 10 2 0 A 2.15 2.45 A1 0.00 0.10 A2 2.15 2.35 b 0.18 0.32 b1 0.13 c 0.23 c1 0.20 D D1 0.25 0.30 0.32 0.20 0.30 10.30 BSC 6.90 7.50 D2 3.65 D3 4.30 e 0.50 BSC E 10.30 BSC E1 7.50 BSC E2 4.30 5.20 E3 2.30 E4 2.90 G1 1.20 G2 1.00 G3 0.80 h 0.30 L 0.55 0.40 0.70 L1 1.40 REF L2 0.25 BSC N 36 R 0.30 R1 0.20 S 0.25 Tolerance of form and position 88/100 Max. aaa 0.20 bbb 0.20 ccc 0.10 ddd 0.20 DocID027886 Rev 7 0.85 VNQ7003SY Package information Table 80. PowerSSO-36 mechanical data (continued) Dimensions Ref. Millimeters Min. 12.2 Typ. eee 0.10 fff 0.20 ggg 0.15 Max. PowerSSO-36 packing information Figure 36. PowerSSO-36 reel 13" DocID027886 Rev 7 89/100 93 Package information VNQ7003SY Table 81. Reel dimensions Description Value (1) Base quantity 1000 Bulk quantity 1000 A (max) 330 B (min) 1.5 C ( 0.2) 13 F 20.2 G (+2 / -0) 24.4 N (min) 100 T (max) 30.4 1. All dimensions are in mm. Figure 37. PowerSSO-36 carrier tape Table 82. PowerSSO-36 carrier tape dimensions 90/100 Description Value (1) A0 10.90 0.10 B0 10.80 0.10 K0 2.75 0.10 K1 2.45 0.10 D0 1.50 (+0.10 / -0) D1 1.60 0.10 DocID027886 Rev 7 VNQ7003SY Package information Table 82. PowerSSO-36 carrier tape dimensions (continued) Description Value (1) P0 4.00 0.10 P1 12.00 0.10 P2 2.00 0.10 P10 40.00 0.20 E 1.75 0.10 F 11.50 0.10 W 24.00 0.30 T 0.30 0.05 1. All dimensions are in mm DocID027886 Rev 7 91/100 93 Package information VNQ7003SY Figure 38. PowerSSO-36 schematic drawing of leader and trailer tape 12.3 PowerSSO-36 marking information Figure 39. PowerSSO-36 marking information .BSLJOHBSFB 4QFDJBMGVODUJPOEJHJU &OHJOFFSJOHTBNQMF CMBOL$PNNFSDJBMTBNQMF 1PXFS4405017*&8 OPUJOTDBMF Note: 92/100 ("1($'5 Engineering Samples: Parts marked as "&" are not yet qualified and therefore not approved for use in production. ST is not responsible for any consequences resulting from such use. In no event will ST be liable for the customer using any of these engineering samples in production. ST's Quality department must be contacted prior to any decision to use these engineering samples to run a qualification activity. Commercial Samples: fully qualified parts from ST standard production with no usage restrictions. DocID027886 Rev 7 VNQ7003SY 13 Order codes Order codes Table 83. Device summary Package Order codes Tube PowerSSO-36 VNQ7003SY DocID027886 Rev 7 Tape and reel VNQ7003SYTR 93/100 93 Revision history 14 VNQ7003SY Revision history Table 84. Document revision history Date Revision 01-Jul-2015 1 Initial release. 2 - Updated Chapter 2: Functional description Updated Chapter 3: Protections - Updated Chapter 6: Programmable blanking window Table 53: Absolute maximum ratings: - -VCCJS: added parameter - -IDIN0,1, IDIN2,3: updated values - Table 55: DC characteristics - Mode 1: - -VDD_POR_ON: updated value - -IDD, IDDstd: updated test conditions Table 56: DC characteristics - Mode 2: - -IDD, IDDstd: updated test conditions - Table 58: AC characteristics (SDI, SCK, CSN, SDO pins) - Mode 2: - -COUT, CIN: updated test conditions - Table 60: Dynamic characteristics - Mode 2: - -tWDTB: added parameter Table 62: Power section: - -IS: updated test conditions - Table 63: Logic inputs (IN0,1,2,3 pins): - -VICL0,1: updated test conditions and values - -tSTEP: removed parameter - Updated Table 67: BULB - switching (VCC = 13 V; Normal switch mode) - Added Table 68: BULB - switching (VCC = 13 V; Fast switch mode) Table 69: BULB - protection and diagnostic - -IlimH_ch0,1, IlimH_ch2,3: Updated values - Table 70: BULB - CurrentSense (7 V < VCC < 18 V, channel 0,1; Tj - = - 40 C to 150 C) - -K0, dK0/K0, ISENSE_DIS: deleted parameter - -K1, dK1/K1, K2, dK2/K2, K3, dK3/K3, ISENSE0: updated test conditions and values - -tDSENSE2H, tDSENSE2L, tD_XtoY: added parameters - Table 71: BULB - CurrentSense (7 V < VCC < 18 V, channel 2,3; Tj - = - 40 C to 150 C) - -K0, dK0/K0, ISENSE_DIS: deleted parameter - -K1, dK1/K1, K2, dK2/K2, K3, dK3/K3, ISENSE0: updated test conditions and values - -tDSENSE2H, tDSENSE2L, tD_XtoY: added parameters - Table 72: LED - power section - RON Ch0,1: updated test conditions - Updated Table 73: LED - switching (VCC = 13 V; Normal switch mode) 25-Nov-2015 94/100 Description of changes DocID027886 Rev 7 VNQ7003SY Revision history Table 84. Document revision history (continued) Date 25-Nov-2015 (cont.) Revision 2 Description of changes - Added Table 74: LED - switching (VCC = 13 V; Fast switch mode) Table 74: LED - switching (VCC = 13 V; Fast switch mode) - -K0, dK0/K0, K1, dK1/K1, K2, dK2/K2, ISENSE0: updated test conditions and values - -K3, dK3/K3, ISENSE_DIS: deleted parameter - -tDSENSE2H, tDSENSE2L, tD_XtoY: added parameters - - - - - - 11-Oct-2016 3 - - - - - Minor text edits and formatting changes throughout document. Updated Table 1: "Pin functionality description" with Pin 13 information Updated Table 53: "Absolute maximum ratings" -VCC parameter description Removed Table 56: "DC characteristics - Mode 2" VDD Pin footnote Updated Section 7.4.1: "BULB mode" WON and WOFF values Updated Table 70: "BULB - CurrentSense (VCC = 7 V to 18 V, channel 0,1; Tj = -40 C to 150 C)" and Table 71: "BULB - CurrentSense (VCC = 7 V to 18 V, channel 2,3; Tj = -40 C to 150 C)" and Table 76: "LED - CurrentSense (VCC = 7 V to 18 V; Tj = - 40 C to 150 C)": -ISENSE test conditions -tDSENSE2H and tDSENSE2L test conditions and values -VSENSE_SAT test conditions Updated Table 77: "Component values" DocID027886 Rev 7 95/100 99 Revision history VNQ7003SY Table 84. Document revision history (continued) Date 04-May-2017 96/100 Revision Description of changes 4 Minor text changes throughout document. Figure 1: "Block diagram": Replaced image Table 1: "Pin functionality description": Modified Function descriptions of the SDO, VDD and CurrentSense pins Section 2.1: "Device interfaces": Changed VDD option from 3.3 V to 3 V Table 3: "Frame 1: read (ROM) 0x3FH 0x--": Added footnote Section 3.2: "Junction overtemperature (OT)": Added reference to Limp Home Mode Updated the Global Status Byte that is cleared to bit 2 for Latched OFF operation Section 3.3: "Power limitation (PL)": Added reference to Limp Home Mode Updated the Global Status Byte that is cleared to bit 2 for Latched OFF operation Section 4.2: "SPI protocol": Restructured subsections to separately describe the SDI/SDO 8-bit and 16-bit formats. Table 20: "RAM memory map": Updated entries for memory addresses 05h, 08h, 09h and 3Eh Table 21: "ROM memory map": Updated Content column entry for memory address 0Ah Figure 16: "VNQ7003SY: 4-channel direct input block diagram": Replaced image Table 31: "CTLR - Control Register": Added GOSTBY value required to enter Normal mode for bit 0. Table 32: "DIENCR - Direct Input Enable Control Register": Updated content column entry for bits 7-4 Removed Section: Address 0x05h - Test Register (TEST) Table 36: "CSMUXCR - CurrentSense Multiplexer Control Register": Updated content column entry for bits 7-4 Table 38: "SOCR - SPI Output Control Register": Updated content column entry for bits 3-0 Section 4.6.8: "Address 0x08h - Channel Latch OFF Timer Control Register (ch0, ch1) (CHLOFFTCR0,1)": Updated section title (changed CHLOFFTCR1 register name to CHLOFFTCR0,1) Table 39: "Channel configuration": Updated table title, table headings and blanking time window durations Table 40: "CHLOFFTCR0,1 - Channel Latch OFF Timer Control Register (ch0, ch1)": Modified all register names and updated content column entries accordingly DocID027886 Rev 7 VNQ7003SY Revision history Table 84. Document revision history (continued) Date 04-May-2017 (cont.) Revision Description of changes 4 Section 4.6.9: "Address 0x09h - Channel Latch OFF Timer Control Register (ch2, ch3) (CHLOFFTCR2,3)": Updated section title (changed CHLOFFTCR2 register name to CHLOFFTCR2,3) Table 41: "CHLOFFTCR2,3 - Channel Latch OFF Timer Control Register (ch2, ch3)": Modified register names for bits 7-4 and updated content column entries accordingly Section 5.8: "Address 0x31h - Open-load OFF-State / Stuck to VCC Status Register (OLOFFCR )": Updated section title (changed STKFLTR register name to OLOFFCR) Table 46: "STKFLTR - Open-load OFF-State / Stuck to VCC Status Register": Changed bit name from STKSRX to OLOFFCR Table 47: "CHLOFFSR - Channels latch-off status register": Updated bit names for bits 3-0 Table 50: "CONFIG - Configuration Register": Updated Reset column values for bits 7-5 Section 6: "Programmable blanking window": Updated register names (from CHLOFFTCR1 to CHLOFFTCR0,1 and from CHLOFFTCR2 to CHLOFFTCR2,3) Table 51: "Time values written by MCU and their real value in timer register": Updated all Typical value of blanking time values Section 6.4: "Registers": -Updated register names (from CHLOFFTCR1 to CHLOFFTCR0,1 and from CHLOFFTCR2 to CHLOFFTCR2,3) -Added "Clear command" description to the subsection: Latch-OFF Flag register access Table 52: "Absolute maximum ratings": Updated VREG parameter value from 3 V to 3.6 V Table 54: "DC characteristics - Mode 1": -Updated min, typ and max values for VDD_POR_ON and VDD_POR_OFF -Updated max values for parameters VSDI_CL (IIN = 1 mA), VSCK_CL (IIN = 1 mA) and VCL_CSN (IIN = 1 mA) Table 55: "DC characteristics - Mode 2": Updated max values for parameters VSDI_CL (IIN = 1 mA), VSDK_CL (IIN = 1 mA) and VCL_CSN (IIN = 1 mA) Table 57: "AC characteristics (SDI, SCK, CSN, SDO pins) - Mode 2": Updated max values for parameters COUT and CIN Table 58: "Dynamic characteristics - Mode 1": Updated min, typ and max values for parameter tstdby_out Table 59: "Dynamic characteristics - Mode 2": Inserted min, typ or max values for all parameters except tSCLK, tCSNQV and tCSNQT Table 67: "BULB - switching (VCC = 13 V; Fast switch mode)": Updated min, typ and/or max values for all parameters DocID027886 Rev 7 97/100 99 Revision history VNQ7003SY Table 84. Document revision history (continued) Date 04-May-2017 (cont.) 98/100 Revision Description of changes 4 Table 60: "VREG pin - Mode 1": -Inserted max value for VREG (Supply voltage in standby mode) -Updated output impedance symbol to ZREG Updated test conditions for ZREG and IREG_Max -Updated typ value for IREG_Max Table 61: "Power section": -Changed parameter symbol IS to Istby -Added parameter Is(on) - Supply current in ON-state Table 62: "Logic inputs (IN0,1,2,3 pins)": Changed symbol VDIN to VIN in Test condition column Table 63: "Protection": Updated min and max values for parameters VDS_OVL, tBlanking and tON_MIN Table 64: "Open-load detection (7V < VCC < 18 V)": Updated min, typ and max values for parameters IPU and tDOLOFF Table 66: "BULB - switching (VCC = 13 V; Normal switch mode)": -Updated min, typ and max values for parameters tdon, tdoff, tskew, (dVOUT/dt)off and WOFF -Changed WOFF to Ch2,3 in Parameter column of WON Table 68: "BULB - protection and diagnostic": Updated Parameters and Test conditions for VDEMAG Table 69: "BULB - CurrentSense (7 V < VCC < 18 V, channel 0,1; Tj = -40 C to 150 C)": -Updated min values for parameters VSENSE_SAT and IOUT_SAT_BULB -Updated typ values for parameters K1, K2 and K3 -Updated max values for parameters ISENSE0 (current sense enabled), tDSENSE1H, tDSENSE2H and tD_XtoY -Changed Tj to -40 C in Parameter column of VSENSE_SAT Table 70: "BULB - CurrentSense (7 V < VCC < 18 V, channel 2,3; Tj = -40 C to 150 C)": -Updated min values for parameters VSENSE_SAT and IOUT_SAT_BULB -Updated typ values for parameters K1, K2, K3, tDSENSE1H and tDSENSE2H -Updated max values for parameters tDSENSE1H, tDSENSE2H and tDSENSE2L -Changed Tj to -40 C in Parameter column of VSENSE_SAT Table 72: "LED - switching (VCC = 13 V; Normal switch mode)": Updated min, typ and/or max values for all parameters DocID027886 Rev 7 VNQ7003SY Revision history Table 84. Document revision history (continued) Date Revision Description of changes 4 Table 73: "LED - switching (VCC = 13 V; Fast switch mode)": Updated min, typ and/or max values for all parameters Table 75: "LED - CurrentSense (7 V < VCC < 18 V; Tj = -40 C to 150 C)": -Updated min value for parameter IOUT_SAT_LED -Updated typ values for parameters K0, K1, K2 and tDSENSE2H -Updated max values for parameters ISENSE0, tDSENSE2H and tDSENSE2L -Changed Tj to -40 C in Parameter column of VSENSE_SAT Figure 25: "CurrentSense delay characteristics": Replaced image Figure 26: "Switching characteristics": Replaced image Figure 27: "M0-7 SPI Standard connection SPI only": Replaced image Figure 28: "M0-7 SPI standard, full connection": Replaced image Section 10.3: "PowerSSO-36 marking information": Updated information regarding the use of engineering samples 13-Dec-2017 5 - Updated Table 52: Absolute maximum ratings , added EMAX0,1 and EMAX2,3 values. - Updated Table 53: Thermal data - Updated Table 54: DC characteristics - Mode 1 - Updated Table 63: Protection - Updated Table 65: BULB - power section - Updated Table 67: BULB - switching (VCC = 13 V; Fast switch mode) - Updated Table 69: BULB - CurrentSense (7 V < VCC < 18 V, channel 0,1; Tj = 40 C to 150 C) - Updated Table 70: BULB - CurrentSense (7 V < VCC < 18 V, channel 2,3; Tj = 40 C to 150 C) - Updated Table 73: LED - switching (VCC = 13 V; Fast switch mode) - Updated Table 75: LED - CurrentSense (7 V < VCC < 18 V; Tj = -40 C to 150 C) - Updated Figure 26: Switching characteristics - Updated Table 76: ISO 7637-2 - electrical transient conduction along supply line Added Section 10: Package and PCB thermal data Added Section 11: Maximum demagnetization energy (VCC = 16 V) 15-Jan-2018 6 Updated Table 54: DC characteristics - Mode 1. 7 In Table 67: BULB - switching (VCC = 13 V; Fast switch mode): - updated parameter description of "tskew" symbol from "Turn-off turn-on time" in "Turn-off turn-on time Ch2,3" - updated parameter description of "(dVOUT/dt)on" symbol from "Turn-on voltage slope" in "Turn-on voltage slope Ch2,3" - updated parameter description of "(dVOUT/dt)off" symbol from "Turn-off voltage slope" in "Turn-off voltage slope Ch2,3" - updated parameter description of "WON" symbol from "Switching losses energy" in "Switching losses energy at turn-on Ch2,3" - updated parameter description of "WOFF" symbol from "Switching losses energy" in "Switching losses energy at turn-off Ch2,3" Updated title of Table 72: LED - switching (VCC = 13 V; Normal switch mode) 04-May-2017 (cont.) 04-Apr-2018 DocID027886 Rev 7 99/100 99 VNQ7003SY IMPORTANT NOTICE - PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST's terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers' products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. (c) 2018 STMicroelectronics - All rights reserved 100/100 DocID027886 Rev 7