Not for new design. Use new F461-F464 Series. R75 MKP Series HIGH PERFORMANCES METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. AND PULSE APPLICATIONS Loose Fig. 1 Fig. 2 Typical applications: deflection circuits in TV-sets and monitors (S-correction), resonant capacitor in electronic ballast and compact lamp, power factor correction and coupling capacitor in SMPS, timing and oscillator circuits. PRODUCT CODE: R75 (Digit 12: 0 to 9) Fig. 3 Taped p=7.5 0.5 Od0.05 p=10 0.6 15p27.5 0.8 p = 37.5 1.0 Pitch (mm) Box thickness (mm) 7.5 10.0 15.0 15.0 22.5 27.5 37.5 All All <7.5 7.5 All All All Maximum dimensions (mm) B max H max L max B +0.1 B +0.2 B +0.2 B +0.2 B +0.2 B +0.2 B +0.3 H +0.1 H +0.1 H +0.1 H +0.1 H +0.1 H +0.1 H +0.1 L +0.2 L +0.2 L +0.3 L +0.5 L +0.3 L +0.3 L +0.3 All dimensions are in mm. PRODUCT CODE SYSTEM The part number, comprising 14 digits, is formed as follows: 1 2 3 4 5 6 7 8 9 10 11 12 13 R 7 5 14 - Digit 1 to 3 Series code. Digit 4 d.c. rated voltage: G = 160V I = 250V M= 400V P = 630V Q = 1000V R= 1250V T= 1600V U =2000V Digit 5 Pitch: D = 7.5 mm; F = 10.0mm; I = 15.0mm; N = 22.5 mm; R = 27.5mm; W = 37.5mm Digit 6 to 9 Digits 7 - 8 - 9 indicate the first three digits of Capacitance value and the 6th digit indicates the number of zeros that must be added to obtain the Rated Capacitance in pF. Digit 10 to 11 Mechanical version and/or packaging (table 1) Digit 12 Identifies the dimensions and electrical characteristics (0 to 9). Digit 13 Internal use. Digit 14 Capacitance tolerance: J=5%; K=10%; M=20% GENERAL TECHNICAL DATA Dielectric: polypropylene film. Plates: aluminium layer deposited by evaporation under vacuum. Winding: non-inductive type. Leads: for O 0,6mm : tinned wire for O = 0,5mm : tinned wire, low thermical conductivity Protection: plastic case, thermosetting resin filled. Box material is solvent resistant and flame retardant according to UL94 V0. Marking: manufacturer's logo, series (R75), dielectric code (MKP), capacitance, tolerance, D.C. rated voltage, manufacturing date code. Climatic category: 55/105/56 IEC 60068-1 Operating temperature range: -55 to +105C Related documents:IEC 60384-16 Table 1 (for more detailed information, please refer to pages 14). Standard packaging style Lead length (mm) AMMO-PACK AMMO-PACK AMMO-PACK REEL O 355mm REEL O 355mm REEL O 500mm REEL O 500mm Loose, short leads Loose, long leads (p<10mm) Loose, long leads (p10mm) Loose, long leads (p15mm) Taping style P2 (mm) 06.35 12.70 19.05 06.35 12.70 12.70 19.05 Fig. (No.) 1 2 3 1 2 2 3 Ordering code Pitch (mm) 7.5 10.0/15.0 22.5 7.5 10.0/15.0 10.0/15.0 22.5/27.5 (Digit 10 to 11) 04+2 DQ DQ DQ CK GY CK CK AA 17+1/-2 Z3 18+1/-1 JM 30 25+2/-1 40 50 +5 Note: Ammo-pack is the preferred packaging for taped version. 105 09/2008 Not for new design. Use new F461-F464 Series. R75 MKP Series HIGH PERFORMANCES METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. AND PULSE APPLICATIONS PRODUCT CODE: R75 (Digit 12: 0 to 9) Rated Cap. 0.10 0.12 0.15 0.18 0.22 0.12 0.15 0.18 0.22 0.27 0.33 F F F F F F F F F F F 160Vdc / 70Vac Reduced sizes B 4.0 5.0 5.0 6.0 6.0 4.0 4.0 5.0 5.0 6.0 6.0 H 9.0 10.5 10.5 12.0 12.0 9.0 9.0 11.0 11.0 12.0 12.0 L 10.0 10.0 10.0 10.5 10.5 13.0 13.0 13.0 13.0 13.0 13.0 p 7.5 7.5 7.5 7.5 7.5 10.0 10.0 10.0 10.0 10.0 10.0 Max dv/dt (V/s) 100 100 100 100 100 90 90 90 90 90 90 Max K0 (V2/s) 32 E3 32 E3 32 E3 32 E3 32 E3 28 E3 28 E3 28 E3 28 E3 28 E3 28 E3 Part Number R75GD R75GD R75GD R75GD R75GD R75GF R75GF R75GF R75GF R75GF R75GF single sided metallized polypropylene film 3100--B-3120--B-3150--B-3180--A-3220--A-3120--A-3150--A-3180--A-3220--A-3270--A-3330--A-- 1 section (160Vdc) The derating curves of previous table are not included this catalogue, available upon request. Rated Cap. 0.068 0.082 0.10 0.12 0.15 0.18 0.082 0.10 0.12 0.15 0.18 0.22 0.18 0.22 0.27 0.33 0.39 0.47 0.47 0.56 0.56 0.68 0.68 0.82 1.0 160Vdc / 90Vac Std dimensions B H L F 4.0 9.0 10.0 F 4.0 9.0 10.0 F 5.0 10.5 10.0 F 5.0 10.5 10.0 F 6.0 12.0 10.5 F 6.0 12.0 10.5 F 4.0 9.0 13.0 F 4.0 9.0 13.0 F 5.0 11.0 13.0 F 5.0 11.0 13.0 F 6.0 12.0 13.0 F 6.0 12.0 13.0 F 5.0 11.0 18.0 F 5.0 11.0 18.0 F 6.0 12.0 18.0 F 6.0 12.0 18.0 F 7.5 13.5 18.0 F 7.5 13.5 18.0 F 9.0 12.5 18.0 F 8.5 14.5 18.0 F 9.0 12.5 18.0 F 8.5 14.5 18.0 F 13.0 12.0 18.0 F 10.0 16.0 18.0 F 10.0 16.0 18.0 p 7.5 7.5 7.5 7.5 7.5 7.5 10.0 10.0 10.0 10.0 10.0 10.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 Max dv/dt (V/s) 300 300 300 300 300 300 180 180 180 180 180 180 100 100 100 100 100 100 100 100 100 100 100 100 100 Max K0 (V2s) 74 E3 74 E3 74 E3 74 E3 74 E3 74 E3 58 E3 58 E3 58 E3 58 E3 58 E3 58 E3 32 E3 32 E3 32 E3 32 E3 32 E3 32 E3 32 E3 32 E3 32 E3 32 E3 32 E3 32 E3 32 E3 Mechanical version and packaging (Table1) Internal use Tolerance: J (5%); K (10%); M (20%) Rated Cap. Part Number R75GD2680--4-R75GD2820--4-R75GD3100--4-R75GD3120--4-R75GD3150--0-R75GD3180--3-R75GF 2820--0-R75GF 3100--3-R75GF 3120--0-R75GF 3150--0-R75GF 3180--0-R75GF 3220--3-R75GI 3180--0-R75GI 3220--0-R75GI 3270--0-R75GI 3330--0-R75GI 3390--0-R75GI 3470--0-R75GI 3470--6-R75GI 3560--0-R75GI 3560--6-R75GI 3680--0-R75GI 3680--6-R75GI 3820--0-R75GI 4100--0-- 0.82 1.0 1.2 1.5 1.8 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F 160Vdc / 90Vac Std dimensions B 7.0 7.0 8.5 10.0 10.0 9.0 9.0 11.0 11.0 13.0 13.0 13.0 14.0 18.0 18.0 22.0 22.0 11.0 11.0 11.0 13.0 16.0 16.0 19.0 19.0 20.0 20.0 24.0 30.0 30.0 H 16.0 16.0 17.0 18.5 18.5 17.0 17.0 20.0 20.0 22.0 22.0 25.0 28.0 33.0 33.0 37.0 37.0 22.0 22.0 22.0 24.0 28.5 28.5 32.0 32.0 40.0 40.0 44.0 45.0 45.0 L 26.5 26.5 26.5 26.5 26.5 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 p 22.5 22.5 22.5 22.5 22.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 Max dv/dt (V/s) 60 60 60 60 60 50 50 50 50 50 50 50 50 50 50 50 50 35 35 35 35 35 35 35 35 35 35 35 35 35 Max K0 Part Number (V2/s) 19 E3 19 E3 19 E3 19 E3 19 E3 16 E3 16 E3 16 E6 16 E3 16 E3 16 E3 16 E3 16 E3 16 E3 16 E3 16 E3 16 E3 11 E3 11 E3 11 E3 11 E3 11 E3 11 E3 11 E3 11 E3 11 E3 11 E3 11 E3 11 E3 11 E3 R75GN 3820--0-R75GN 4100--0-R75GN 4120--0-R75GN 4150--0-R75GN 4180--0-R75GR 4150--0-R75GR 4180--0-R75GR 4220--3-R75GR 4270--0-R75GR 4330--0-R75GR 4390--0-R75GR 4470--3-R75GR 4560--0-R75GR 4680--0-R75GR 4820--0-R75GR 5100--0-R75GR 5120--0-R75GW 4330--0-R75GW 4390--0-R75GW 4470--0-R75GW 4560--0-R75GW 4680--0-R75GW 4820--0-R75GW 5100--0-R75GW 5120--0-R75GW 5150--0-R75GW 5180--0-R75GW 5220--0-R75GW 5270--0-R75GW 5330--0-- Mechanical version and packaging (Table1) Internal use Tolerance: J (5%); K (10%); M (20%) All dimensions are mm. Note: If the working voltage (V) is lower than the rated voltage (VR), the capacitor may work at higher dv/dt. In this case the maximum value allowed is obtained multiplying the above value (see table dv/dt) with the ratio VR /V. The pulse characteristic K0 depends on the voltage wave-form and in any case it cannot overcome the value given in the above table. The dv/dt test is carried out at 2 times the above values. 09/2008 106 Not for new design. Use new F461-F464 Series. R75 MKP Series HIGH PERFORMANCES METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. AND PULSE APPLICATIONS PRODUCT CODE: R75 (Digit 12: 0 to 9) Rated Cap. 0.068 0.082 0.10 0.12 0.15 0.18 0.082 0.10 0.12 0.15 0.18 0.22 F F F F F F F F F F F F 250Vdc / 140Vac Reduced sizes B 4.0 4.0 5.0 5.0 6.0 6.0 4.0 4.0 5.0 5.0 6.0 6.0 H 9.0 9.0 10.5 10.5 12.0 12.0 9.0 9.0 11.0 11.0 12.0 12.0 L 10.0 10.0 10.0 10.0 10.5 10.5 13.0 13.0 13.0 13.0 13.0 13.0 p 7.5 7.5 7.5 7.5 7.5 7.5 10.0 10.0 10.0 10.0 10.0 10.0 Max dv/dt (V/s) 180 180 180 180 180 180 150 150 150 150 150 150 Max K0 (V /s) 90 E3 90 E3 90 E3 90 E3 90 E3 90 E3 75 E3 75 E3 75 E3 75 E3 75 E3 75 E3 Part Number 2 R75ID R75ID R75ID R75ID R75ID R75ID R75IF R75IF R75IF R75IF R75IF R75IF 2680--B-2820--B-3100--B-3120--B-3150--A-3180--A-2820--A-3100--A-3120--A-3150--A-3180--A-3220--A-- single sided metallized polypropylene film 1 section (250Vdc) The derating curves of previous table are not included this catalogue, available upon request. Rated Cap. 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.39 0.47 0.47 0.56 0.56 0.68 0.68 0.82 0.82 1.0 1.2 F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F 250Vdc / 160Vac Std dimensions B 4.0 4.0 4.0 4.0 4.0 5.0 5.0 6.0 6.0 4.0 4.0 4.0 4.0 4.0 5.0 5.0 6.0 6.0 5.0 5.0 5.0 5.0 6.0 6.0 7.5 9.0 7.5 9.0 7.5 9.0 8.5 13.0 10.0 13.0 10.0 11.0 H 9.0 9.0 9.0 9.0 9.0 10.5 10.5 12.0 12.0 9.0 9.0 9.0 9.0 9.0 11.0 11.0 12.0 12.0 11.0 11.0 11.0 11.0 12.0 12.0 13.5 12.5 13.5 12.5 13.5 12.5 14.5 12.0 16.0 12.0 16.0 19.0 L 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.5 10.5 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 p 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 Max dv/dt (V/s) 650 650 650 650 650 650 650 650 650 550 550 550 550 550 550 550 550 550 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 Max K0 (V2/s) 150 E3 150 E3 150 E3 150 E3 150 E3 150 E3 150 E3 150 E3 150 E3 140 E3 140 E3 140 E3 140 E3 140 E3 140 E3 140 E3 140 E3 140 E3 100 E3 100 E3 100 E3 100 E3 100 E3 100 E3 100 E3 100 E3 100 E3 100 E3 100 E3 100 E3 100 E3 100 E3 100 E3 100 E3 100 E3 100 E3 Mechanical version and packaging (Table1) Internal use Tolerance: J (5%); K (10%); M (20%) All dimensions are mm. Rated Cap. Part Number R75ID 2270--4-R75ID 2330--4-R75ID 2390--4-R75ID 2470--4-R75ID 2560--4-R75ID 2680--4-R75ID 2820--4-R75ID 3100--3-R75ID 3120--3-R75IF 2330--0-R75IF 2390--0-R75IF 2470--3-R75IF 2560--3-R75IF 2680--3-R75IF 2820--3-R75IF 3100--3-R75IF 3120--3-R75IF 3150--3-R75II 3120--3-R75II 3150--3-R75II 3180--4-R75II 3220--4-R75II 3270--4-R75II 3330--4-R75II 3390--4-R75II 3390--7-R75II 3470--4-R75II 3470--8-R75II 3560--4-R75II 3560--8-R75II 3680--4-R75II 3680--8-R75II 3820--4-R75II 3820--8-R75II 4100--4-R75II 4120--4-- 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 250Vdc / 160Vac Std dimensions F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F B 6.0 6.0 6.0 6.0 7.0 7.0 8.5 10.0 10.0 11.0 13.0 13.0 9.0 9.0 9.0 9.0 11.0 11.0 13.0 13.0 13.0 14.0 18.0 18.0 22.0 22.0 11.0 11.0 11.0 13.0 16.0 16.0 19.0 19.0 20.0 20.0 24.0 24.0 30.0 H 15.0 15.0 15.0 15.0 16.0 16.0 17.0 18.5 18.5 20.0 22.0 22.0 17.0 17.0 17.0 17.0 20.0 20.0 22.0 22.0 25.0 28.0 33.0 33.0 37.0 37.0 22.0 22.0 22.0 24.0 28.5 28.5 32.0 32.0 40.0 40.0 44.0 44.0 45.0 L 26.5 26.5 26.5 26.5 26.5 26.5 26.5 26.5 26.5 26.5 26.5 26.5 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 p 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 Max dv/dt (V/s) 125 125 125 125 125 125 125 125 125 125 125 125 100 100 100 100 100 100 100 100 100 100 100 100 100 100 40 40 40 40 40 40 40 40 40 40 40 40 40 Max K0 Part Number (V2/s) 63 E3 63 E3 63 E3 63 E3 63 E3 63 E3 63 E3 63 E3 63 E3 63 E3 63 E3 63 E3 50 E3 50 E3 50 E3 50 E3 50 E3 50 E3 50 E3 50 E3 50 E3 50 E3 50 E3 50 E3 50 E3 50 E3 20 E3 20 E3 20 E3 20 E3 20 E3 20 E3 20 E3 20 E3 20 E3 20 E3 20 E3 20 E3 20 E3 R75IN 3390--3-R75IN 3470--3-R75IN 3560--4-R75IN 3680--4-R75IN 3820--4-R75IN 4100--4-R75IN 4120--4-R75IN 4150--4-R75IN 4180--4-R75IN 4220--4-R75IN 4270--4-R75IN 4330--4-R75IR 4100--3-R75IR 4120--3-R75IR 4150--4-R75IR 4180--4-R75IR 4220--5-R75IR 4270--4-R75IR 4330--4-R75IR 4390--4-R75IR 4470--5-R75IR 4560--4-R75IR 4680--4-R75IR 4820--4-R75IR 5100--4-R75IR 5120--4-R75IW4330--4-R75IW4390--4-R75IW4470--4-R75IW4560--4-R75IW4680--4-R75IW4820--4-R75IW5100--4-R75IW5120--4-R75IW5150--4-R75IW5180--4-R75IW5220--4-R75IW5270--4-R75IW5330--4-- Mechanical version and packaging (Table1) Internal use Tolerance: J (5%); K (10%); M (20%) Note: If the working voltage (V) is lower than the rated voltage (VR), the capacitor may work at higher dv/dt. In this case the maximum value allowed is obtained multiplying the above value (see table dv/dt) with the ratio VR /V. The pulse characteristic K0 depends on the voltage wave-form and in any case it cannot overcome the value given in the above table. The dv/dt test is carried out at 2 times the above values. 107 09/2008 Not for new design. Use new F461-F464 Series. R75 MKP Series HIGH PERFORMANCES METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. AND PULSE APPLICATIONS PRODUCT CODE: R75 (Digit 12: 0 to 9) Rated Cap. 0.027 0.033 0.039 0.047 0.056 0.068 400Vdc / 200Vac Reduced sizes F F F F F F B 4.0 5.0 5.0 5.0 6.0 6.0 H 9.0 10.5 10.5 10.5 12.0 12.0 L 10.0 10.0 10.0 10.0 10.5 10.5 p 7.5 7.5 7.5 7.5 7.5 7.5 Max dv/dt (V/s) 390 390 390 390 390 390 Max K0 Part Number (V /s) 312 E3 312 E3 312 E3 312 E3 312 E3 312 E3 R75MD 2270--B-R75MD 2330--B-R75MD 2390--B-R75MD 2470--B-R75MD 2560--A-R75MD 2680--A-- single sided metallized polypropylene film 2 1 section (400Vdc) The derating curves of previous table are not included this catalogue, available upon request. Rated Cap. 0.010 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.22 0.27 0.27 0.33 0.33 0.39 0.47 0.56 400Vdc / 220Vac* Std dimensions F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F B 4.0 4.0 4.0 4.0 4.0 5.0 5.0 6.0 6.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 6.0 6.0 5.0 5.0 5.0 6.0 6.0 7.5 7.5 9.0 8.5 9.0 10.0 13.0 10.0 10.0 11.0 H 9.0 9.0 9.0 9.0 9.0 10.5 10.5 12.0 12.0 9.0 9.0 9.0 9.0 11.0 11.0 11.0 12.0 12.0 11.0 11.0 11.0 12.0 12.0 13.5 13.5 12.5 14.5 12.5 16.0 12.0 16.0 16.0 19.0 L 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.5 10.5 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 p 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 Max dv/dt (V/s) 1500 1500 1500 1500 1500 1500 1500 1500 1500 1300 1300 1300 1300 1300 1300 1300 1300 1300 900 900 900 900 900 900 900 900 900 900 900 900 900 900 900 Max K0 (V2/s) 360 E3 360 E3 360 E3 360 E3 360 E3 360 E3 360 E3 360 E3 360 E3 336 E3 336 E3 336 E3 336 E3 336 E3 336 E3 336 E3 336 E3 336 E3 240 E3 240 E3 240 E3 240 E3 240 E3 240 E3 240 E3 240 E3 240 E3 240 E3 240 E3 240 E3 240 E3 240 E3 240 E3 Mechanical version and packaging (Table1) Internal use Tolerance: J (5%); K (10%); M (20%) Rated Cap. Part Number R75MD 2100--4-R75MD 2120--4-R75MD 2150--4-R75MD 2180--4-R75MD 2220--4-R75MD 2270--4-R75MD 2330--4-R75MD 2390--3-R75MD 2470--3-R75F 2150--0-R75F 2180--0-R75F 2220--3-R75F 2270--3-R75F 2330--3-R75F 2390--3-R75F 2470--3-R75F 2560--3-R75F 2680--3-R75MI 2680--3-R75MI 2820--3-R75MI 3100--3-R75MI 3120--3-R75MI 3150--3-R75MI 3180--3-R75MI 3220--3-R75MI 3220--7-R75MI 3270--3-R75MI 3270--7-R75MI 3330--3-R75MI 3330--7-R75MI 3390--3-R75MI 3470--3-R75MI 3560--3-- 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F 400Vdc / 220Vac* Std dimensions B 6.0 6.0 6.0 6.0 7.0 7.0 8.5 10.0 10.0 11.0 13.0 13.0 9.0 9.0 9.0 11.0 11.0 13.0 13.0 13.0 14.0 18.0 18.0 22.0 22.0 11.0 11.0 11.0 11.0 13.0 16.0 16.0 19.0 19.0 19.0 20.0 20.0 24.0 30.0 H 15.0 15.0 15.0 15.0 16.0 16.0 17.0 18.5 18.5 20.0 22.0 22.0 17.0 17.0 17.0 20.0 20.0 22.0 22.0 25.0 28.0 33.0 33.0 37.0 37.0 22.0 22.0 22.0 22.0 24.0 28.5 28.5 32.0 32.0 32.0 40.0 40.0 44.0 45.0 L 26.5 26.5 26.5 26.5 26.5 26.5 26.5 26.5 26.5 26.5 26.5 26.5 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 p 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 Max dv/dt (V/s) 300 300 300 300 300 300 300 300 300 300 300 300 130 130 130 130 130 130 130 130 130 130 130 130 130 70 70 70 70 70 70 70 70 70 70 70 70 70 70 Max K0 Part Number (V2/s) 144 E3 144 E3 144 E3 144 E3 144 E3 144 E3 144 E3 144 E3 144 E3 144 E3 144 E3 144 E3 104 E3 104 E3 104 E3 104 E3 104 E3 104 E3 104 E3 104 E3 104 E3 104 E3 104 E3 104 E3 104 E3 56 E3 56 E3 56 E3 56 E3 56 E3 56 E3 56 E3 56 E3 56 E3 56 E3 56 E3 56 E3 56 E3 56 E3 R75MN 3180--3-R75MN 3220--3-R75MN 3270--3-R75MN 3330--3-R75MN 3390--3-R75MN 3470--3-R75MN 3560--3-R75MN 3680--3-R75MN 3820--3-R75MN 4100--3-R75MN 4120--3-R75MN 4150--3-R75MR 3560--3-R75MR 3680--3-R75MR 3820--3-R75MR 4100--4-R75MR 4120--3-R75MR 4150--3-R75MR 4180--3-R75MR 4220--4-R75MR 4270--3-R75MR 4330--3-R75MR 4390--3-R75MR 4470--3-R75MR 4560--3-R75MW 4120--3-R75MW 4150--3-R75MW 4180--3-R75MW 4220--3-R75MW 4270--3-R75MW 4330--3-R75MW 4390--3-R75MW 4470--3-R75MW 4560--3-R75MW 4680--3-R75MW 4820--3-R75MW 5100--4-R75MW 5120--3-R75MW 5150--3-- Mechanical version and packaging (Table1) Internal use Tolerance: J (5%); K (10%); M (20%) All dimensions are mm. Note: If the working voltage (V) is lower than the rated voltage (VR), the capacitor may work at higher dv/dt. In this case the maximum value allowed is obtained multiplying the above value (see table dv/dt) with the ratio VR /V. The pulse characteristic K0 depends on the voltage wave-form and in any case it cannot overcome the value given in the above table. The dv/dt test is carried out at 2 times the above values. * Not suitable for across-the-line applications. Please refer to Interference Suppression Capacitors (page 151) 09/2008 108 Not for new design. Use new F461-F464 Series. R75 MKP Series HIGH PERFORMANCES METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. AND PULSE APPLICATIONS PRODUCT CODE: R75 (Digit 12: 0 to 9) Rated Cap. 0.010 0.012 0.015 0.018 0.022 0.027 F F F F F F 630Vdc / 220Vac* Reduced sizes B 4.0 4.0 5.0 5.0 6.0 6.0 H 9.0 9.0 10.5 10.5 12.0 12.0 L 10.0 10.0 10.0 10.0 10.5 10.5 p 7.5 7.5 7.5 7.5 7.5 7.5 Max dv/dt (V/s) 600 600 600 600 600 600 Max K0 Part Number (V2/s) 760 E3 760 E3 760 E3 760 E3 760 E3 760 E3 R75PD2100--B-R75PD2120--B-R75PD2150--B-R75PD2180--B-R75PD2220--A-R75PD2270--A-- single sided metallized polypropylene film 1 section (630Vdc) The derating curves of previous table are not included this catalogue, available upon request. Rated Cap. 3300 3900 4700 5600 6800 8200 0.010 0.012 0.015 0.018 3300 3900 4700 5600 6800 8200 0.010 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.10 0.12 0.12 0.15 0.15 0.18 0.18 0.22 0.27 0.33 pF pF pF pF pF pF F F F F pF pF pF pF pF pF F F F F F F F F F F F F F F F F F F F F F F F 630Vdc / 250Vac* Std dimensions B H L p 4.0 9.0 10.0 7.5 4.0 9.0 10.0 7.5 4.0 9.0 10.0 7.5 4.0 9.0 10.0 7.5 4.0 9.0 10.0 7.5 4.0 9.0 10.0 7.5 5.0 10.5 10.0 7.5 5.0 10.5 10.0 7.5 6.0 12.0 10.5 7.5 6.0 12.0 10.5 7.5 4.0 9.0 13.0 10.0 4.0 9.0 13.0 10.0 4.0 9.0 13.0 10.0 4.0 9.0 13.0 10.0 4.0 9.0 13.0 10.0 4.0 9.0 13.0 10.0 4.0 9.0 13.0 10.0 4.0 9.0 13.0 10.0 5.0 11.0 13.0 10.0 5.0 11.0 13.0 10.0 6.0 12.0 13.0 10.0 5.0 11.0 18.0 15.0 5.0 11.0 18.0 15.0 5.0 11.0 18.0 15.0 5.0 11.0 18.0 15.0 5.0 11.0 18.0 15.0 6.0 12.0 18.0 15.0 6.0 12.0 18.0 15.0 7.5 13.5 18.0 15.0 9.0 12.5 18.0 15.0 7.5 13.5 18.0 15.0 9.0 12.5 18.0 15.0 8.5 14.5 18.0 15.0 13.0 12.0 18.0 15.0 10.0 16.0 18.0 15.0 13.0 12.0 18.0 15.0 10.0 16.0 18.0 15.0 11.0 19.0 18.0 15.0 11.0 19.0 18.0 15.0 Max dv/dt (V/s) 2400 2400 2400 2400 2400 2400 2400 2400 2400 2400 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 Max K0 (V /s) 760 E3 760 E3 760 E3 760 E3 760 E3 760 E3 760 E3 760 E3 760 E3 760 E3 690 E3 690 E3 690 E3 690 E3 690 E3 690 E3 690 E3 690 E3 690 E3 690 E3 690 E3 504 E3 504 E3 504 E3 504 E3 504 E3 504 E3 504 E3 504 E3 504 E3 504 E3 504 E3 504 E3 504 E3 504 E3 504 E3 504 E3 504 E3 504 E3 Mechanical version and packaging (Table1) Internal use Tolerance: J (5%); K (10%); M (20%) Rated Cap. Part Number 2 R75PD1330--4-R75PD1390--4-R75PD1470--4-R75PD1560--4-R75PD1680--4-R75PD1820--4-R75PD2100--4-R75PD2120--4-R75PD2150--3-R75PD2180--3-R75PF 1330--0-R75PF 1390--0-R75PF 1470--0-R75PF 1560--0-R75PF 1680--0-R75PF 1820--0-R75PF 2100--3-R75PF 2120--3-R75PF 2150--3-R75PF 2180--3-R75PF 2220--3-R75PI 2270--0-R75PI 2330--0-R75PI 2390--3-R75PI 2470--3-R75PI 2560--3-R75PI 2680--3-R75PI 2820--3-R75PI 3100--3-R75PI 3100--7-R75PI 3120--3-R75PI 3120--7-R75PI 3150--3-R75PI 3150--7-R75PI 3180--3-R75PI 3180--7-R75PI 3220--3-R75PI 3270--3-R75PI 3330--3-- 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F 630Vdc / 250Vac* Std dimensions B H L p 6.0 15.0 26.5 22.5 6.0 15.0 26.5 22.5 6.0 15.0 26.5 22.5 6.0 15.0 26.5 22.5 7.0 16.0 26.5 22.5 7.0 16.0 26.5 22.5 8.5 17.0 26.5 22.5 10.0 18.5 26.5 22.5 10.0 18.5 26.5 22.5 11.0 20.0 26.5 22.5 11.0 20.0 26.5 22.5 13.0 22.0 26.5 22.5 9.0 17.0 32.0 27.5 9.0 17.0 32.0 27.5 11.0 20.0 32.0 27.5 11.0 20.0 32.0 27.5 13.0 22.0 32.0 27.5 13.0 22.0 32.0 27.5 14.0 28.0 32.0 27.5 14.0 28.0 32.0 27.5 18.0 33.0 32.0 27.5 18.0 33.0 32.0 27.5 22.0 37.0 32.0 27.5 22.0 37.0 32.0 27.5 11.0 22.0 41.5 37.5 11.0 22.0 41.5 37.5 11.0 22.0 41.5 37.5 13.0 24.0 41.5 37.5 13.0 24.0 41.5 37.5 16.0 28.5 41.5 37.5 16.0 28.5 41.5 37.5 19.0 32.0 41.5 37.5 19.0 32.0 41.5 37.5 19.0 32.0 41.5 37.5 20.0 40.0 41.5 37.5 20.0 40.0 41.5 37.5 24.0 44.0 41.5 37.5 30.0 45.0 41.5 37.5 Max dv/dt (V/s) 400 400 400 400 400 400 400 400 400 400 400 400 180 180 180 180 180 180 180 180 180 180 180 180 90 90 90 90 90 90 90 90 90 90 90 90 90 90 Max K0 Part Number (V /s) 315 E3 315 E3 315 E3 315 E3 315 E3 315 E3 315 E3 315 E3 315 E3 315 E3 315 E3 315 E3 227 E3 227 E3 227 E3 227 E3 227 E3 227 E3 227 E3 227 E3 227 E3 227 E3 227 E3 227 E3 113 E3 113 E3 113 E3 113 E3 113 E3 113 E3 113 E3 113 E3 113 E3 113 E3 113 E3 113 E3 113 E3 113 E3 R75PN 2820--3-R75PN 3100--3-R75PN 3120--3-R75PN 3150--3-R75PN 3180--3-R75PN 3220--3-R75PN 3270--3-R75PN 3330--3-R75PN 3390--3-R75PN 3470--3-R75PN 3560--3-R75PN 3680--3-R75PR 3390--3-R75PR 3470--4-R75PR 3560--3-R75PR 3680--3-R75PR 3820--3-R75PR 4100--3-R75PR 4120--4-R75PR 4150--3-R75PR 4180--3-R75PR 4220--3-R75PR 4270--3-R75PR 4330--3-R75PW 3680--3-R75PW 3820--3-R75PW 4100--3-R75PW 4120--3-R75PW 4150--3-R75PW 4180--3-R75PW 4220--3-R75PW 4270--3-R75PW 4330--3-R75PW 4390--4-R75PW 4470--3-R75PW 4560--4-R75PW 4680--3-R75PW 4820--3-- 2 Mechanical version and packaging (Table1) Internal use Tolerance: J (5%); K (10%); M (20%) All dimensions are mm. Note: If the working voltage (V) is lower than the rated voltage (VR), the capacitor may work at higher dv/dt. In this case the maximum value allowed is obtained multiplying the above value (see table dv/dt) with the ratio VR /V. The pulse characteristic K0 depends on the voltage wave-form and in any case it cannot overcome the value given in the above table. The dv/dt test is carried out at 2 times the above values. * Not suitable for across-the-line applications. Please refer to Interference Suppression Capacitors (page 151) 109 09/2008 Not for new design. Use new F461-F464 Series. R75 MKP Series HIGH PERFORMANCES METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. AND PULSE APPLICATIONS PRODUCT CODE: R75 (Digit 12: 0 to 9) single sided metallized polypropylene film single sided metallized polypropylene film 1 section (1000Vdc/250Vac) Rated Cap. 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.047 0.056 0.056 0.068 0.068 0.082 0.10 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F 1000Vdc / 250Vac* Std dimensions B 5.0 5.0 5.0 5.0 6.0 6.0 7.5 7.5 9.0 8.5 9.0 8.5 13.0 10.0 11.0 6.0 6.0 6.0 7.0 7.0 8.5 10.0 10.0 11.0 9.0 9.0 11.0 11.0 13.0 13.0 13.0 14.0 18.0 18.0 18.0 22.0 22.0 11.0 11.0 11.0 11.0 13.0 13.0 16.0 16.0 19.0 19.0 20.0 20.0 24.0 30.0 30.0 H 11.0 11.0 11.0 11.0 12.0 12.0 13.5 13.5 12.5 14.5 12.5 14.5 12.0 16.0 19.0 15.0 15.0 15.0 16.0 16.0 17.0 18.5 18.5 20.0 17.0 17.0 20.0 20.0 22.0 22.0 25.0 28.0 33.0 33.0 33.0 37.0 37.0 22.0 22.0 22.0 22.0 24.0 24.0 28.5 28.5 32.0 32.0 40.0 40.0 44.0 45.0 45.0 L 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 26.5 26.5 26.5 26.5 26.5 26.5 26.5 26.5 26.5 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 p 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 3 sections (1000Vdc/400Vac) Max dv/dt (V/s) 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 600 600 600 600 600 600 600 600 600 200 200 200 200 200 200 200 200 200 200 200 200 200 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 Max K0 (V2s) 900 E3 900 E3 900 E3 900 E3 900 E3 900 E3 900 E3 900 E3 900 E3 900 E3 900 E3 900 E3 900 E3 900 E3 900 E3 600 E3 600 E3 600 E3 600 E3 600 E3 600 E3 600 E3 600 E3 600 E3 400 E3 400 E4 400E4 400 E3 400 E3 400 E3 400 E3 400 E3 400 E3 400 E3 400 E3 400 E4 400 E3 300 E3 300 E3 300 E3 300 E3 300 E3 300E3 300 E3 300 E3 300 E3 300 E3 300 E3 300 E3 300 E3 300 E3 300 E3 Rated Cap. Part Number 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 R75QI 2120--0-R75QI 2150--0-R75QI 2180--0-R75QI 2220--0-R75QI 2270--0-R75QI 2330--0-R75QI 2390--0-R75QI 2470--0-R75QI 2470--6-R75QI 2560--0-R75QI 2560--6-R75QI 2680--0-R75QI 2680--6-R75QI 2820--0-R75QI 3100--0-R75QN 2470--0-R75QN 2560--0-R75QN 2680--0-R75QN 2820--0-R75QN 3100--0-R75QN 3120--0-R75QN 3150--0-R75QN 3180--0-R75QN 3220--0-R75QR 3150--0-R75QR 3180--0-R75QR 3220--1-R75QR 3270--0-R75QR 3330--0-R75QR 3390--0-R75QR 3470--1-R75QR 3560--1-R75QR 3680--0-R75QR 3820--0-R75QR 4100--0-R75QR 4120--0-R75QR 4150--0-R75QW 3270--0-R75QW 3330--0-R75QW 3390--0-R75QW 3470--0-R75QW 3560--0-R75QW 3680--0-R75QW 3820--0-R75QW 4100--0-R75QW 4120--0-R75QW 4150--0-R75QW 4180--0-R75QW 4220--0-R75QW 4270--0-R75QW 4330--0-R75QW 4390--0-- Max dv/dt (V/s) 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 Max K0 Part Number (V2/s) 8.0 E6 8.0 E6 8.0 E6 8.0 E6 8.0 E6 8.0 E6 8.0 E6 8.0 E6 8.0 E6 8.0 E6 8.0 E6 8.0 E6 8.0 E6 8.0 E6 8.0 E6 8.0 E6 8.0 E6 8.0 E6 8.0 E6 8.0 E6 R75QD 0220--3-R75QD 0270--3-R75QD 0330--3-R75QD 0390--3-R75QD 0470--3-R75QD 0560--3-R75QD 0680--3-R75QD 0820--3-R75QD 1100--3-R75QD 1120--3-R75QD 1150--3-R75QD 1180--3-R75QD 1220--3-R75QD 1270--3-R75QD 1330--3-R75QD 1390--3-R75QD 1470--3-R75QD 1560--3-R75QD 1680--3-R75QD 1820--3-- Mechanical version and packaging (Table1) Internal use Tolerance: J (5%); K (10%); M (20%) All dimensions are mm. Note: If the working voltage (V) is lower than the rated voltage (VR), the capacitor may work at higher dv/dt. In this case the maximum value allowed is obtained multiplying the above value (see table dv/dt) with the ratio VR /V. The pulse characteristic K0 depends on the voltage waveform and in any case it cannot overcome the value given in the above table. The dv/dt test is carried out at 2 times the above values. Mechanical version and packaging (Table1) Internal use Tolerance: J (5%); K (10%); M (20%) Note: * Not suitable for across-the-line applications. Please refer to Interference Suppression Capacitors (page 151) 09/2008 pF pF pF pF pF pF pF pF pF pF pF pF pF pF pF pF pF pF pF pF 1000Vdc / 400Vac Std dimensions B H L p 3.0 8.0 10.0 7.5 3.0 8.0 10.0 7.5 3.0 8.0 10.0 7.5 3.0 8.0 10.0 7.5 3.0 8.0 10.0 7.5 3.0 8.0 10.0 7.5 3.0 8.0 10.0 7.5 3.0 8.0 10.0 7.5 3.0 8.0 10.0 7.5 4.0 9.0 10.0 7.5 4.0 9.0 10.0 7.5 4.0 9.0 10.0 7.5 4.0 9.0 10.0 7.5 4.0 9.0 10.0 7.5 4.0 9.0 10.0 7.5 5.0 10.5 10.0 7.5 5.0 10.5 10.0 7.5 5.0 10.5 10.0 7.5 6.0 12.0 10.5 7.5 6.0 12.0 10.5 7.5 110 Not for new design. Use new F461-F464 Series. R75 MKP Series HIGH PERFORMANCES METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. AND PULSE APPLICATIONS PRODUCT CODE: R75 (Digit 12: 0 to 9) single sided metallized polypropylene film 3 sections (1250Vdc)-(1600Vdc) Rated Cap. 8200 0.010 0.012 0.015 0.018 0.022 0.022 0.027 0.027 0.033 0.033 0.039 0.047 0.056 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 pF F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F 1250Vdc / 600Vac Std dimensions B 5.0 5.0 6.0 6.0 7.5 7.5 9.0 8.5 13.0 10.0 13.0 10.0 11.0 11.0 6.0 6.0 7.0 7.0 8.5 10.0 10.0 11.0 13.0 9.0 9.0 11.0 11.0 13.0 13.0 13.0 18.0 18.0 18.0 22.0 22.0 11.0 11.0 13.0 16.0 16.0 16.0 19.0 20.0 20.0 24.0 24.0 30.0 H 11.0 11.0 12.0 12.0 13.5 13.5 12.5 14.5 12.0 16.0 12.0 16.0 19.0 19.0 15.0 15.0 16.0 16.0 17.0 18.5 18.5 20.0 22.0 17.0 17.0 20.0 20.0 22.0 25.0 25.0 33.0 33.0 33.0 37.0 37.0 22.0 22.0 24.0 28.5 28.5 28.5 32.0 40.0 40.0 44.0 44.0 45.0 L 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 26.5 26.5 26.5 26.5 26.5 26.5 26.5 26.5 26.5 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 p 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 27.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 Max dv/dt (V/s) 3300 3300 3300 3300 3300 3300 3300 3300 3300 3300 3300 3300 3300 3300 2100 2100 2100 2100 2100 2100 2100 2100 2100 500 500 500 500 500 500 500 500 500 500 500 500 360 360 360 360 360 360 360 360 360 360 360 360 Max K0 (V2/s) 825 E4 825 E4 825 E4 825 E4 825 E4 825 E4 825 E4 825 E4 825 E4 825 E4 825 E4 825 E4 825 E4 825 E4 525 E4 525 E4 525 E4 525 E4 525 E4 525 E4 525 E4 525 E4 525 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 125 E4 Mechanical version and packaging (Table1) Internal use Tolerance: J (5%); K (10%); M (20%) Rated Cap. Part Number R75RI 1820--3-R75RI 2100--3-R75RI 2120--3-R75RI 2150--3-R75RI 2180--3-R75RI 2220--3-R75RI 2220--7-R75RI 2270--3-R75RI 2270--7-R75RI 2330--3-R75RI 2330--7-R75RI 2390--3-R75RI 2470--3-R75RI 2560--3-R75RN 2330--3-R75RN 2390--3-R75RN 2470--3-R75RN 2560--3-R75RN 2680--3-R75RN 2820--3-R75RN 3100--3-R75RN 3120--3-R75RN 3150--3-R75RR 3100--4-R75RR 3120--4-R75RR 3150--4-R75RR 3180--4-R75RR 3220--4-R75RR 3270--4-R75RR 3330--4-R75RR 3390--4-R75RR 3470--4-R75RR 3560--4-R75RR 3680--4-R75RR 3820--4-R75RW 3270--3-R75RW 3330--3-R75RW 3390--3-R75RW 3470--4-R75RW 3560--4-R75RW 3680--4-R75RW 3820--4-R75RW 4100--3-R75RW 4120--4-R75RW 4150--4-R75RW 4180--3-R75RW 4220--3-- 3900 4700 5600 6800 8200 0.010 0.012 0.015 0.018 0.018 0.022 0.022 0.027 0.033 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 pF pF pF pF pF F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F 1600Vdc / 650Vac Std dimensions B H L p 4.0 10.0 18.0 15.0 4.0 10.0 18.0 15.0 5.0 11.0 18.0 15.0 5.0 11.0 18.0 15.0 6.0 12.0 18.0 15.0 6.0 12.0 18.0 15.0 7.5 13.5 18.0 15.0 7.5 13.5 18.0 15.0 8.5 14.5 18.0 15.0 9.0 12.5 18.0 15.0 10.0 16.0 18.0 15.0 13.0 12.0 18.0 15.0 10.0 16.0 18.0 15.0 11.0 19.0 18.0 15.0 6.0 15.0 26.5 22.5 7.0 16.0 26.5 22.5 7.0 16.0 26.5 22.5 8.5 17.0 26.5 22.5 10.0 18.5 26.5 22.5 10.0 18.5 26.5 22.5 11.0 20.0 26.5 22.5 13.0 22.0 26.5 22.5 13.0 22.0 26.5 22.5 9.0 17.0 32.0 27.5 9.0 17.0 32.0 27.5 11.0 20.0 32.0 27.5 11.0 20.0 32.0 27.5 13.0 22.0 32.0 27.5 13.0 22.0 32.0 27.5 13.0 25.0 32.0 27.5 18.0 33.0 32.0 27.5 18.0 33.0 32.0 27.5 18.0 33.0 32.0 27.5 22.0 37.0 32.0 27.5 22.0 37.0 32.0 27.5 11.0 22.0 41.5 37.5 11.0 22.0 41.5 37.5 13.0 24.0 41.5 37.5 16.0 28.5 41.5 37.5 16.0 28.5 41.5 37.5 16.0 28.5 41.5 37.5 19.0 32.0 41.5 37.5 19.0 32.0 41.5 37.5 20.0 40.0 41.5 37.5 24.0 44.0 41.5 37.5 24.0 44.0 41.5 37.5 30.0 45.0 41.5 37.5 Max dv/dt (V/s) 6000 6000 6000 6000 6000 6000 6000 6000 6000 6000 6000 6000 6000 6000 3000 3000 3000 3000 3000 3000 3000 3000 3000 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 750 750 750 750 750 750 750 750 750 750 750 750 Max K0 Part Number (V /s) 1900 E4 1900 E4 1900 E4 1900 E4 1900 E4 1900 E4 1900 E4 1900 E4 1900 E4 1900 E4 1900 E4 1900 E4 1900 E4 1900 E4 960 E4 960 E4 960 E4 960 E4 960 E4 960 E4 960 E4 960 E4 960 E4 480 E4 480 E4 480 E4 480 E4 480 E4 480 E4 480 E4 480 E4 480 E4 480 E4 480 E4 480 E4 240 E4 240 E4 240 E4 240 E4 240 E4 240 E4 240 E4 240 E4 240 E4 240 E4 240 E4 240 E4 R75TI 1390--3-R75TI 1470--3-R75TI 1560--3-R75TI 1680--3-R75TI 1820--3-R75TI 2100--3-R75TI 2120--3-R75TI 2150--3-R75TI 2180--3-R75TI 2180--7-R75TI 2220--3-R75TI 2220--7-R75TI 2270--3-R75TI 2330--3-R75TN 2270--3-R75TN 2330--3-R75TN 2390--3-R75TN 2470--3-R75TN 2560--3-R75TN 2680--3-R75TN 2820--3-R75TN 3100--3-R75TN 3120--3-R75TR 2680--3-R75TR 2820--3-R75TR 3100--4-R75TR 3120--3-R75TR 3150--3-R75TR 3180--3-R75TR 3220--4-R75TR 3270--3-R75TR 3330--3-R75TR 3390--3-R75TR 3470--3-R75TR 3560--3-R75TW 3180--3-R75TW 3220--3-R75TW 3270--3-R75TW 3330--3-R75TW 3390--3-R75TW 3470--3-R75TW 3560--3-R75TW 3680--3-R75TW 3820--3-R75TW 4100--3-R75TW 4120--3-R75TW 4150--3-- 2 Mechanical version and packaging (Table1) Internal use Tolerance: J (5%); K (10%); M (20%) All dimensions are mm. Note: If the working voltage (V) is lower than the rated voltage (VR), the capacitor may work at higher dv/dt. In this case the maximum value allowed is obtained multiplying the above value (see table dv/dt) with the ratio VR /V. The pulse characteristic K0 depends on the voltage wave-form and in any case it cannot overcome the value given in the above table. The dv/dt test is carried out at 2 times the above values. 111 09/2008 Not for new design. Use new F461-F464 Series. R75 MKP Series HIGH PERFORMANCES METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. AND PULSE APPLICATIONS PRODUCT CODE: R75 (Digit 12: 0 to 9) Rated Cap. 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 0.010 0.012 0.012 0.015 0.015 0.018 0.018 0.022 0.027 4700 5600 6800 8200 0.010 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 pF pF pF pF pF pF pF pF pF pF pF pF F F F F F F F F F pF pF pF pF F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F 2000Vdc / 700Vac Std dimensions B H L p 4.0 10.0 18.0 15.0 4.0 10.0 18.0 15.0 4.0 10.0 18.0 15.0 4.0 10.0 18.0 15.0 4.0 10.0 18.0 15.0 4.0 10.0 18.0 15.0 4.0 10.0 18.0 15.0 5.0 11.0 18.0 15.0 5.0 11.0 18.0 15.0 6.0 12.0 18.0 15.0 6.0 12.0 18.0 15.0 7.5 13.5 18.0 15.0 7.5 13.5 18.0 15.0 8.5 14.5 18.0 15.0 9.0 12.5 18.0 15.0 8.5 14.5 18.0 15.0 13.0 12.0 18.0 15.0 10.0 16.0 18.0 15.0 13.0 12.0 18.0 15.0 11.0 19.0 18.0 15.0 11.0 19.0 18.0 15.0 6.0 15.0 26.5 22.5 6.0 15.0 26.5 22.5 6.0 15.0 26.5 22.5 6.0 15.0 26.5 22.5 6.0 15.0 26.5 22.5 6.0 15.0 26.5 22.5 6.0 15.0 26.5 22.5 6.0 15.0 26.5 22.5 6.0 15.0 26.5 22.5 7.0 16.0 26.5 22.5 8.5 17.0 26.5 22.5 10.0 18.5 26.5 22.5 10.0 18.5 26.5 22.5 11.0 20.0 26.5 22.5 13.0 22.0 26.5 22.5 9.0 17.0 32.0 27.5 9.0 17.0 32.0 27.5 9.0 17.0 32.0 27.5 11.0 20.0 32.0 27.5 11.0 20.0 32.0 27.5 13.0 22.0 32.0 27.5 13.0 25.0 32.0 27.5 14.0 28.0 32.0 27.5 14.0 28.0 32.0 27.5 18.0 33.0 32.0 27.5 18.0 33.0 32.0 27.5 22.0 37.0 32.0 37.5 22.0 37.0 32.0 27.5 11.0 22.0 41.5 37.5 13.0 24.0 41.5 37.5 13.0 24.0 41.5 37.5 16.0 28.5 41.5 37.5 16.0 28.5 41.5 37.5 19.0 32.0 41.5 37.5 19.0 32.0 41.5 37.5 20.0 40.0 41.5 37.5 20.0 40.0 41.5 37.5 24.0 44.0 41.5 37.5 24.0 44.0 41.5 37.5 Max dv/dt (V/s) 9500 9500 9500 9500 9500 9500 9500 9500 9500 9500 9500 9500 9500 9500 9500 9500 9500 9500 9500 9500 9500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 500 500 500 500 500 500 500 500 500 500 500 Max K0 Part Number (V /s) 3800 E4 3800 E4 3800 E4 3800 E4 3800 E4 3800 E4 3800 E4 3800 E4 3800 E4 3800 E4 3800 E4 3800 E4 3800 E4 3800 E4 3800 E4 3800 E4 3800 E4 3800 E4 3800 E4 3800 E4 3800 E4 1400 E4 1400 E4 1400 E4 1400 E4 1400 E4 1400 E4 1400 E4 1400 E4 1400 E4 1400 E4 1400 E4 1400 E4 1400 E4 1400 E4 1400 E4 400 E4 400 E4 400 E4 400 E4 400 E4 400 E4 400 E4 400 E4 400 E4 400 E4 400 E4 400 E4 400 E4 200 E4 200 E4 200 E4 200 E4 200 E4 200 E4 200 E4 200 E4 200 E4 200 E4 200 E4 R75UI 1100--4-R75UI 1120--4-R75UI 1150--4-R75UI 1180--4-R75UI 1220--4-R75UI 1270--4-R75UI 1330--4-R75UI 1390--3-R75UI 1470--3-R75UI 1560--3-R75UI 1680--3-R75UI 1820--3-R75UI 2100--3-R75UI 2120--3-R75UI 2120--7-R75UI 2150--3-R75UI 2150--7-R75UI 2180--3-R75UI 2180--7-R75UI 2220--3-R75UI 2270--3-R75UN 1470--3-R75UN 1560--3-R75UN 1680--3-R75UN 1820--3-R75UN 2100--3-R75UN 2120--3-R75UN 2150--3-R75UN 2180--3-R75UN 2220--3-R75UN 2270--3-R75UN 2330--3-R75UN 2390--3-R75UN 2470--3-R75UN 2560--3-R75UN 2680--3-R75UR 2470--3-R75UR 2560--3-R75UR 2680--4-R75UR 2820--4-R75UR 3100--3-R75UR 3120--3-R75UR 3150--4-R75UR 3180--3-R75UR 3220--4-R75UR 3270--3-R75UR 3330--4-R75UR 3390--3-R75UR 3470--4-R75UW3150--3-R75UW3180--3-R75UW3220--3-R75UW3270--3-R75UW3330--3-R75UW3390--3-R75UW3470--3-R75UW3560--4-R75UW3680--3-R75UW3820--4-R75UW4100--3-- single sided metallized polypropylene film 2 3 sections (2000Vdc) All dimensions are mm. Note: If the working voltage (V) is lower than the rated voltage (VR), the capacitor may work at higher dv/dt. In this case the maximum value allowed is obtained multiplying the above value (see table dv/dt) with the ratio VR /V. The pulse characteristic K0 depends on the voltage wave-form and in any case it cannot overcome the value given in the above table. The dv/dt test is carried out at 2 times the above values. Mechanical version and packaging (Table1) Internal use Tolerance: J (5%); K (10%); M (20%) 09/2008 112 Not for new design. Use new F461-F464 Series. R75 MKP Series HIGH PERFORMANCES METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. AND PULSE APPLICATIONS PRODUCT CODE: R75 (Digit 12: 0 to 9) ELECTRICAL CHARACTERISTICS TEST METHOD AND PERFORMANCE Rated voltage (VR): 160Vdc - 250Vdc - 400Vdc - 630Vdc -1000Vdc for 1 section. 1250Vdc - 1600Vdc - 2000Vdc for 3 sections. Damp heat, steady state: Test conditions Temperature: Relative humidity (RH): Test duration: Rated temperature (TR): +85C Temperature derated voltage: The following decreasing factor has to be applied on the rated voltage: +85C to +105C: 2.00% per C for VR (d.c.) +85C to +105C: 1.25% per C for VR (a.c.) Performance Capacitance change |C/C|: 2% DF change (tg): 10x10-4 at 1kHz Insulation resistance: 50% of initial limit. Endurance: Capacitance range: 1000 pF to 33F for 1 section. 1000 pF to 2.2F for 3 sections. Test conditions Temperature: Test duration: Voltage applied: Capacitance values: E12 series (IEC 60063 Norm). Performance Total self-inductance (L): (Lead length ~2 mm) 7.5 8 10 9 15 10 22.5 18 27.5 18 37.5 20 Dissipation factor (DF): tgx10-4 at +25C5C kHz 1 10 100 C0.1F 04 06 25 +85C2C 2000 h 1.25xVR Capacitance change |C/C|: 3% 10x10-4 at 10kHz for C1F DF change (tg): 10x10-4 at 01kHz for C>1F Insulation resistance: 50% of initial limit. Capacitance tolerances (measured at 1 kHz): 5% (J); 10% (K); 20% (M). Pitch (mm) L (nH) +40C2C 93% 2% 56 days 0.1<C1.0F 5 8 Resistance to soldering heat: Test conditions 1<C4.7F 6 Solder bath temperature: +260C5C Dipping time (with heat screen):10 s1 s C>4.7F 10 Performance Capacitance change |C/C|: 1% 10x10-4 at 10kHz for C1F DF change (tg): 10x10-4 at 01kHz for C>1F Insulation resistance: initial limit. Insulation resistance: Test conditions Temperature: +25C5C Voltage charge time: 1min Voltage charge: 100Vdc Performance 1x105 M for C0.33F (5x105 M)* 30000 s for C >0.33F (150000 s)* * Typical value. Long term stability (after two years): Storage: standard environmental conditions (see page 12) Performance Capacitance change |C/C|: 0.5% Test voltage between terminations: 1.6xVR applied for 2 s at +25C5C 113 09/2008 Not for new design. Use new F461-F464 Series. R75 MKP Series HIGH PERFORMANCES METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. AND PULSE APPLICATIONS PRODUCT CODE: R75 (Digit 12: 0 to 9) MAX. VOLTAGE (Vr.m.s.) VERSUS FREQUENCY (sinusoidal wave-form / Th 40C) Note: p (pitch) in mm. 09/2008 114 Not for new design. Use new F461-F464 Series. R75 MKP Series HIGH PERFORMANCES METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. AND PULSE APPLICATIONS PRODUCT CODE: R75 (Digit 12: 0 to 9) MAX. CURRENT (Ir.m.s.) VERSUS FREQUENCY (sinusoidal wave-form / Th 40C) Note: p (pitch) in mm. 115 09/2008 Not for new design. Use new F461-F464 Series. KEMET Corporation World Headquarters Europe Asia 2835 KEMET Way Simpsonville, SC 29681 Southern Europe Geneva, Switzerland Tel: 41-22-715-0100 Northeast Asia Paris, France Tel: 33-1-4646-1009 Shenzhen, China Tel: 86-755-2518-1306 Sasso Marconi, Italy Tel: 39-051-939111 Beijing, China Tel: 86-10-5829-1711 Milan, Italy Tel: 39-02-57518176 Shanghai, China Tel: 86-21-6447-0707 Fort Lauderdale, FL Tel: 954-766-2800 Rome, Italy Tel: 39-06-23231718 Taipei, Taiwan Tel: 886-2-27528585 North America Madrid, Spain Tel: 34-91-804-4303 Southeast Asia Mailing Address: P.O. Box 5928 Greenville, SC 29606 www.kemet.com Tel: 864-963-6300 Fax: 864-963-6521 Corporate Offices Southeast Lake Mary, FL Tel: 407-855-8886 Northeast Wilmington, MA Tel: 978-658-1663 West Chester, PA Tel: 610-692-4642 Central Europe Hong Kong Tel: 852-2305-1168 Singapore Tel: 65-6586-1900 Landsberg, Germany Tel: 49-8191-3350800 Penang, Malaysia Tel: 60-4-6430200 Dortmund, Germany Tel: 49-2307-3619672 Bangalore, India Tel: 91-806-53-76817 Kwidzyn, Poland Tel: 48-55-279-7025 Central Schaumburg, IL Tel: 847-882-3590 Carmel, IN Tel: 317-706-6742 West Milpitas, CA Tel: 408-433-9950 Mexico Zapopan, Jalisco Tel: 52-33-3123-2141 Northern Europe Bishop's Stortford, United Kingdom Tel: 44-1279-757201 Weymouth, United Kingdom Tel: 44-1305-830747 Coatbridge, Scotland Tel: 44-1236-434455 Farjestaden, Sweden Tel: 46-485-563934 Espoo, Finland Tel: 358-9-5406-5000 Digitally signed by Marcy Brand DN: c=US, st=FL, l=Fort Lauderdale, o=KEMET Corporation, ou=Marketing Communications, cn=Marcy Brand, email=marcybrand@kemet.com Date: 2012.07.18 12:13:42 -04'00' Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1001_C0GHT * 8/9/2011 Not for new design. Use new F461-F464 Series. Other KEMET Resources Tools Resource Location Configure A Part: CapEdge http://capacitoredge.kemet.com SPICE & FIT Software http://www.kemet.com/spice Search Our FAQs: KnowledgeEdge http://www.kemet.com/keask Product Information Resource Location Products Technical Resources (Including Soldering Techniques) RoHS Statement Quality Documents http://www.kemet.com/products http://www.kemet.com/technicalpapers http://www.kemet.com/rohs http://www.kemet.com/qualitydocuments Product Request Resource Location Sample Request Engineering Kit Request http://www.kemet.com/sample http://www.kemet.com/kits Contact Resource Location Website Contact Us Investor Relations www.kemet.com http://www.kemet.com/contact http://www.kemet.com/ir Call Us 1-877-MyKEMET Twitter http://twitter.com/kemetcapacitors Disclaimer All product specifications, statements, information and data (collectively, the "Information") are subject to change without notice. All Information given herein is believed to be accurate and reliable, but is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute - and we specifically disclaim - any warranty concerning suitability for a specific customer application or use. This Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by us with reference to the use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained. Although we design and manufacture our products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not be required. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1001_C0GHT * 8/9/2011