CSD87350Q5D SLPS288C - MARCH 2011 - REVISED OCTOBER 2011 www.ti.com Synchronous Buck NexFETTM Power Block FEATURES DESCRIPTION * * * * * * * * * * * The CSD87350Q5D NexFETTM power block is an optimized design for synchronous buck applications offering high current, high efficiency, and high frequency capability in a small 5-mm x 6-mm outline. Optimized for 5V gate drive applications, this product offers a flexible solution capable of offering a high density power supply when paired with any 5V gate drive from an external controller/driver. 1 2 Half-Bridge Power Block 90% system Efficiency at 25A Up To 40A Operation High Frequency Operation (Up To 1.5MHz) High Density - SON 5-mm x 6-mm Footprint Optimized for 5V Gate Drive Low Switching Losses Ultra Low Inductance Package RoHS Compliant Halogen Free Pb-Free Terminal Plating TEXT ADDED FOR SPACING Top View APPLICATIONS * * * * Synchronous Buck Converters - High Frequency Applications - High Current, Low Duty Cycle Applications Multiphase Synchronous Buck Converters POL DC-DC Converters IMVP, VRM, and VRD Applications 8 VSW 7 VSW 3 6 VSW 4 5 VIN 1 VIN 2 TG TGR PGND (Pin 9) BG P0116-01 TEXT ADDED FOR SPACING ORDERING INFORMATION Device Package Media CSD87350Q5D SON 5-mm x 6-mm Plastic Package 13-Inch Reel Qty Ship 2500 Tape and Reel TEXT ADDED FOR SPACING TEXT ADDED FOR SPACING TEXT ADDED FOR SPACING 95 12 93 10.8 91 9.6 Efficiency (%) 89 8.4 VGS = 5V VIN = 12V VOUT = 1.3V LOUT = 0.3H fSW = 500kHz TA = 25C 87 85 83 81 7.2 6 4.8 3.6 79 2.4 77 1.2 75 0 5 10 15 20 25 Output Current (A) 30 35 40 Power Loss (W) TYPICAL POWER BLOCK EFFICIENCY and POWER LOSS TYPICAL CIRCUIT 0 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. NexFET is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2011, Texas Instruments Incorporated CSD87350Q5D SLPS288C - MARCH 2011 - REVISED OCTOBER 2011 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ABSOLUTE MAXIMUM RATINGS TA = 25C (unless otherwise noted) (1) Parameter Conditions VIN to PGND Voltage range VALUE UNIT -0.8 to 30 V TG to TGR -8 to 10 V BG to PGND -8 to 10 V Pulsed Current Rating, IDM 120 A Power Dissipation, PD 12 W Avalanche Energy EAS Sync FET, ID = 105A, L = 0.1mH 551 Control FET, ID = 60A, L = 0.1mH 180 Operating Junction and Storage Temperature Range, TJ, TSTG (1) mJ C -55 to 150 Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. RECOMMENDED OPERATING CONDITIONS TA = 25 (unless otherwise noted) Parameter Conditions MIN Gate Drive Voltage, VGS MAX 4.5 8 Input Supply Voltage, VIN Switching Frequency, fSW UNIT V 27 CBST = 0.1F (min) 200 V 1500 Operating Current Operating Temperature, TJ kHz 40 A 125 C MAX UNIT POWER BLOCK PERFORMANCE TA = 25 (unless otherwise noted) Parameter Power Loss, PLOSS (1) VIN Quiescent Current, IQVIN (1) Conditions MIN TYP VIN = 12V, VGS = 5V, VOUT = 1.3V, IOUT = 25A, fSW = 500kHz, LOUT = 0.3H, TJ = 25C 3.0 W TG to TGR = 0V ,BG to PGND = 0V 10 A Measurement made with six 10F (TDK C3216X5R1C106KT or equivalent) ceramic capacitors placed across VIN to PGND pins and using a high current 5V driver IC. THERMAL INFORMATION TA = 25C (unless otherwise stated) THERMAL METRIC RJA RJC (1) (2) 2 Junction to ambient thermal resistance (Min Cu) Junction to ambient thermal resistance (Max Cu) 2 (2) TYP MAX UNIT 102 (1) (2) Junction to case thermal resistance (Top of package) Junction to case thermal resistance (PGND Pin) MIN (1) (2) 50 (2) 20 C/W 2 (6.45-cm2) 2 Device mounted on FR4 material with 1-inch Cu. RJC is determined with the device mounted on a 1-inch (6.45-cm2), 2 oz. (0.071-mm thick) Cu pad on a 1.5-inch x 1.5-inch (3.81-cm x 3.81-cm), 0.06-inch (1.52-mm) thick FR4 board. RJC is specified by design while RJA is determined by the user's board design. Submit Documentation Feedback Copyright (c) 2011, Texas Instruments Incorporated CSD87350Q5D SLPS288C - MARCH 2011 - REVISED OCTOBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS TA = 25C (unless otherwise stated) PARAMETER Q1 Control FET TEST CONDITIONS MIN TYP Q2 Sync FET MAX MIN TYP MAX UNIT Static Characteristics BVDSS Drain to Source Voltage VGS = 0V, IDS = 250A IDSS Drain to Source Leakage Current VGS = 0V, VDS = 20V IGSS Gate to Source Leakage Current VDS = 0V, VGS = +10 / -8 VGS(th) Gate to Source Threshold Voltage VDS = VGS, IDS = 250A ZDS(on) (1) Effective AC On-Impedance VIN = 12V, VGS = 5V, VOUT = 1.3V, IOUT = 20A, fSW = 500kHz, LOUT = 0.3H gfs Transconductance VDS = 15V, IDS = 20A 30 30 1 V 1 1 A 100 100 nA 1.4 V 2.1 0.75 5 1.2 m 97 157 S Dynamic Characteristics CISS Input Capacitance COSS Output Capacitance CRSS Reverse Transfer Capacitance RG Series Gate Resistance Qg Gate Charge Total (4.5V) Qgd Gate Charge - Gate to Drain Qgs Gate Charge - Gate to Source Qg(th) Gate Charge at Vth QOSS Output Charge td(on) Turn On Delay Time tr Rise Time td(off) Turn Off Delay Time tf Fall Time 1360 1770 2950 3835 pF 565 735 1300 1690 pF 19 25 50 65 pF 1.3 3.0 0.8 2.0 8.4 10.9 20 26 nC VGS = 0V, VDS = 15V, f = 1MHz VDS = 15V, IDS = 20A VDS = 17V, VGS = 0V VDS = 15V, VGS = 4.5V, IDS = 20A, RG = 2 1.6 3.6 nC 2.6 4.3 nC 1.6 2.3 nC 9.7 28 nC 7 8 ns 17 10 ns 13 33 ns 2.3 4.7 ns Diode Characteristics VSD Diode Forward Voltage IDS = 20A, VGS = 0V 0.85 Qrr Reverse Recovery Charge 12.5 32 nC trr Reverse Recovery Time Vdd = 17V, IF = 20A, di/dt = 300A/s 22 28 ns (1) 1 0.77 1 V Equivalent System Performance based on application testing. See page 9 for details. HD LD HD LG HG 5x6 QFN TTA MIN Rev1 5x6 QFN TTA MIN Rev1 Max RJA = 50C/W when mounted on 1 inch2 (6.45 cm2) of 2-oz. (0.071-mm thick) Cu. LD Max RJA = 102C/W when mounted on minimum pad area of 2-oz. (0.071-mm thick) Cu. HS LG LS HG M0189-01 Copyright (c) 2011, Texas Instruments Incorporated HS LS M0190-01 Submit Documentation Feedback 3 CSD87350Q5D SLPS288C - MARCH 2011 - REVISED OCTOBER 2011 www.ti.com TYPICAL POWER BLOCK DEVICE CHARACTERISTICS TJ = 125C, unless stated otherwise. 10 1.4 VIN = 12V VGS = 5V VOUT = 1.3V fSW = 500kHz LOUT = 0.3H 8 Power Loss (W) 7 6 5 4 3 1.1 1 0.9 0.8 0.7 0.6 1 0.5 0 5 10 15 20 25 Output Current (A) 30 35 0.4 -50 40 45 45 40 40 35 35 Output Current (A) 50 30 25 20 10 5 0 400LFM 200LFM 100LFM Nat Conv VIN = 12V VGS = 5V VOUT = 1.3V fSW = 500kHz LOUT = 0.3H 0 10 20 0 25 50 75 100 125 150 Figure 2. Normalized Power Loss vs Temperature 50 15 -25 TC - Junction Temperature - C Figure 1. Power Loss vs Output Current Output Current (A) 1.2 2 0 VIN = 12V VGS = 5V VOUT = 1.3V fSW = 500kHz LOUT = 0.3H 1.3 Power Loss, Normalized 9 30 25 20 10 5 30 40 50 60 Ambient Temperature (C) 70 80 90 Figure 3. Safe Operating Area - PCB Vertical Mount(1) 0 400LFM 200LFM 100LFM Nat Conv VIN = 12V VGS = 5V VOUT = 1.3V fSW = 500kHz LOUT = 0.3H 15 0 10 20 30 40 50 60 Ambient Temperature (C) 70 80 90 Figure 4. Safe Operating Area - PCB Horizontal Mount(1) 50 45 Output Current (A) 40 35 30 25 20 VIN = 12V VGS = 5V VOUT = 1.3V fSW = 500kHz LOUT = 0.3H 15 10 5 0 0 20 40 60 80 100 Board Temperature (C) 120 140 Figure 5. Typical Safe Operating Area(1) (1) 4 The Typical Power Block System Characteristic curves are based on measurements made on a PCB design with dimensions of 4.0" (W) x 3.5" (L) x 0.062" (H) and 6 copper layers of 1 oz. copper thickness. See Application Section for detailed explanation. Submit Documentation Feedback Copyright (c) 2011, Texas Instruments Incorporated CSD87350Q5D SLPS288C - MARCH 2011 - REVISED OCTOBER 2011 www.ti.com TYPICAL POWER BLOCK DEVICE CHARACTERISTICS (continued) TJ = 125C, unless stated otherwise. TEXT ADDED FOR SPACING TEXT ADDED FOR SPACING 1.5 11.8 1.4 8.8 1.2 5.9 1.1 3.0 1 0.0 0.9 -2.9 0.8 -5.9 0.7 -8.8 0.6 200 350 1.3 2.9 1 0.0 0.9 -2.9 0.8 -5.9 0.7 -8.8 3 5 7 1.5 11.7 1.4 5.9 1.1 2.9 1 0 0.9 -2.9 0.8 -5.9 0.7 0.6 0.5 2 2.5 Output Voltage (V) 3 3.5 4 17 19 21 23 -11.7 17.6 VIN = 12V VGS = 5V VOUT = 1.3V fSW = 500kHz IOUT = 40A 1.3 14.7 11.8 8.8 1.2 5.9 1.1 3 1 0 0.9 -2.9 0.8 -5.9 -8.8 0.7 -8.8 -11.7 0.6 Figure 8. Normalized Power Loss vs. Output Voltage Copyright (c) 2011, Texas Instruments Incorporated Power Loss, Normalized 14.7 SOA Temperature Adj (C) Power Loss, Normalized 1.6 8.8 1.5 11 13 15 Input Voltage (V) Figure 7. Normalized Power Loss vs Input Voltage 17.6 1.2 1 9 TEXT ADDED FOR SPACING VIN = 12V VGS = 5V fSW = 500kHz LOUT = 0.3H IOUT = 40A 1.3 8.8 5.9 TEXT ADDED FOR SPACING 1.6 1.4 11.7 1.1 Figure 6. Normalized Power Loss vs Switching Frequency 1.5 14.6 1.2 0.6 -11.7 500 650 800 950 1100 1250 1400 1550 Switching Frequency (kHz) 17.6 VGS = 5V VOUT = 1.3V LOUT = 0.3H fSW = 500kHz IOUT = 40A SOA Temperature Adj (C) 1.3 14.7 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 Output Inductance (H) 0.9 1 SOA Temperature Adj (C) Power Loss, Normalized 1.4 1.6 Power Loss, Normalized VIN = 12V VGS = 5V VOUT = 1.3V LOUT = 0.3H IOUT = 40A 1.5 17.6 SOA Temperature Adj (C) 1.6 -11.7 1.1 Figure 9. Normalized Power Loss vs. Output Inductance Submit Documentation Feedback 5 CSD87350Q5D SLPS288C - MARCH 2011 - REVISED OCTOBER 2011 www.ti.com TYPICAL POWER BLOCK MOSFET CHARACTERISTICS TA = 25C, unless stated otherwise. TEXT ADDED FOR SPACING 80 70 70 IDS - Drain-to-Source Current - A IDS - Drain-to-Source Current - A TEXT ADDED FOR SPACING 80 60 50 40 30 20 VGS = 8.0V VGS = 4.5V VGS = 4.0V 10 0 0 0.1 0.2 0.3 0.4 0.5 60 50 40 30 20 0 0.6 VGS = 8.0V VGS = 4.5V VGS = 4.0V 10 0 0.05 VDS - Drain-to-Source Voltage - V Figure 10. Control MOSFET Saturation TEXT ADDED FOR SPACING IDS - Drain-to-Source Current - A IDS - Drain-to-Source Current - A 0.3 VDS = 5V 10 1 0.1 0.01 TC = 125C TC = 25C TC = -55C 0 0.5 1 1.5 2 2.5 3 3.5 4 10 1 0.1 0.01 0.001 TC = 125C TC = 25C TC = -55C 0 Figure 12. Control MOSFET Transfer 0.5 1 1.5 2 2.5 VGS - Gate-to-Source Voltage - V 3 Figure 13. Sync MOSFET Transfer TEXT ADDED FOR SPACING TEXT ADDED FOR SPACING 10 8 ID = 20A VDD = 15V 9 VGS - Gate-to-Source Voltage (V) VGS - Gate-to-Source Voltage (V) 0.25 TEXT ADDED FOR SPACING VGS - Gate-to-Source Voltage - V 8 7 6 5 4 3 2 1 0 2 4 6 8 10 12 14 Qg - Gate Charge - nC (nC) Figure 14. Control MOSFET Gate Charge 6 0.2 100 VDS = 5V 0 0.15 Figure 11. Sync MOSFET Saturation 100 0.001 0.1 VDS - Drain-to-Source Voltage - V Submit Documentation Feedback 16 ID = 20A VDD = 15V 7 6 5 4 3 2 1 0 0 5 10 15 20 25 30 35 Qg - Gate Charge - nC (nC) Figure 15. Sync MOSFET Gate Charge Copyright (c) 2011, Texas Instruments Incorporated CSD87350Q5D SLPS288C - MARCH 2011 - REVISED OCTOBER 2011 www.ti.com TYPICAL POWER BLOCK MOSFET CHARACTERISTICS (continued) TA = 25C, unless stated otherwise. TEXT ADDED FOR SPACING TEXT ADDED FOR SPACING 10 10 f = 1MHz VGS = 0V 1 C - Capacitance - nF C - Capacitance - nF 1 0.1 0.01 0.1 0.01 Ciss = Cgd + Cgs Coss = Cds + Cgd Crss = Cgd 0.001 0 5 10 Ciss = Cgd + Cgs Coss = Cds + Cgd Crss = Cgd 15 20 25 30 0.001 0 5 10 VDS - Drain-to-Source Voltage - V 15 20 25 Figure 17. Sync MOSFET Capacitance TEXT ADDED FOR SPACING TEXT ADDED FOR SPACING 2 1.6 ID = 250A ID = 250A VGS(th) - Threshold Voltage - V 1.8 1.6 1.4 1.2 1 0.8 0.6 0.4 1.4 1.2 1 0.8 0.6 0.4 0.2 0.2 0 -75 -25 25 75 125 0 -75 175 -25 TC - Case Temperature - C 25 75 125 Figure 19. Sync MOSFET VGS(th) TEXT ADDED FOR SPACING TEXT ADDED FOR SPACING 16 8 14 12 10 8 6 4 TC = 25C TC = 125C 2 0 1 2 3 4 5 6 7 8 9 VGS - Gate-to- Source Voltage - V Figure 20. Control MOSFET RDS(on) vs VGS Copyright (c) 2011, Texas Instruments Incorporated 10 ID = 20A RDS(on) - On-State Resistance - m ID = 20A RDS(on) - On-State Resistance - m 175 TC - Case Temperature - C Figure 18. Control MOSFET VGS(th) 0 30 VDS - Drain-to-Source Voltage - V Figure 16. Control MOSFET Capacitance VGS(th) - Threshold Voltage - V f = 1MHz VGS = 0V 7 6 5 4 3 2 TC = 25C TC = 125C 1 0 0 1 2 3 4 5 6 7 8 9 10 VGS - Gate-to- Source Voltage - V Figure 21. Sync MOSFET RDS(on) vs VGS Submit Documentation Feedback 7 CSD87350Q5D SLPS288C - MARCH 2011 - REVISED OCTOBER 2011 www.ti.com TYPICAL POWER BLOCK MOSFET CHARACTERISTICS (continued) TA = 25C, unless stated otherwise. TEXT ADDED FOR SPACING TEXT ADDED FOR SPACING 1.8 1.8 Normalized On-State Resistance 1.4 1.2 1 0.8 0.6 0.4 0.2 0 -75 -25 25 75 125 ID = 20A VGS = 8V 1.6 Normalized On-State Resistance ID = 20A VGS = 8V 1.6 1.4 1.2 1 0.8 0.6 0.4 0.2 0 -75 175 -25 TC - Case Temperature - C Figure 22. Control MOSFET Normalized RDS(on) TEXT ADDED FOR SPACING ISD - Source-to-Drain Current - A ISD - Source-to-Drain Current - A 175 TEXT ADDED FOR SPACING 10 1 0.1 0.01 0.001 TC = 25C TC = 125C 0 0.2 0.4 0.6 0.8 1 10 1 0.1 0.01 0.001 0.0001 TC = 25C TC = 125C 0 0.4 0.6 0.8 1 Figure 25. Sync MOSFET Body Diode TEXT ADDED FOR SPACING TEXT ADDED FOR SPACING 1000 I(AV) - Peak Avalanche Current - A 100 10 TC = 25C TC = 125C 1 0.01 0.2 VSD - Source-to-Drain Voltage - V Figure 24. Control MOSFET Body Diode I(AV) - Peak Avalanche Current - A 125 100 VSD - Source-to-Drain Voltage - V 0.1 1 10 t(AV) - Time in Avalanche - ms Figure 26. Control MOSFET Unclamped Inductive Switching 8 75 Figure 23. Sync MOSFET Normalized RDS(on) 100 0.0001 25 TC - Case Temperature - C Submit Documentation Feedback 100 10 TC = 25C TC = 125C 1 0.01 0.1 1 10 t(AV) - Time in Avalanche - ms Figure 27. Sync MOSFET Unclamped Inductive Switching Copyright (c) 2011, Texas Instruments Incorporated CSD87350Q5D SLPS288C - MARCH 2011 - REVISED OCTOBER 2011 www.ti.com APPLICATION INFORMATION Equivalent System Performance Many of today's high performance computing systems require low power consumption in an effort to reduce system operating temperatures and improve overall system efficiency. This has created a major emphasis on improving the conversion efficiency of today's Synchronous Buck Topology. In particular, there has been an emphasis in improving the performance of the critical Power Semiconductor in the Power Stage of this Application (see Figure 28). As such, optimization of the power semiconductors in these applications, needs to go beyond simply reducing RDS(ON). Figure 28. The CSD87350Q5D is part of TI's Power Block product family which is a highly optimized product for use in a synchronous buck topology requiring high current, high efficiency, and high frequency. It incorporates TI's latest generation silicon which has been optimized for switching performance, as well as minimizing losses associated with QGD, QGS, and QRR. Furthermore, TI's patented packaging technology has minimized losses by nearly eliminating parasitic elements between the Control FET and Sync FET connections (see Figure 29). A key challenge solved by TI's patented packaging technology is the system level impact of Common Source Inductance (CSI). CSI greatly impedes the switching characteristics of any MOSFET which in turn increases switching losses and reduces system efficiency. As a result, the effects of CSI need to be considered during the MOSFET selection process. In addition, standard MOSFET switching loss equations used to predict system efficiency need to be modified in order to account for the effects of CSI. Further details behind the effects of CSI and modification of switching loss equations are outlined in TI's Application Note SLPA009. Figure 29. Copyright (c) 2011, Texas Instruments Incorporated Submit Documentation Feedback 9 CSD87350Q5D SLPS288C - MARCH 2011 - REVISED OCTOBER 2011 www.ti.com The combination of TI's latest generation silicon and optimized packaging technology has created a benchmarking solution that outperforms industry standard MOSFET chipsets of similar RDS(ON) and MOSFET chipsets with lower RDS(ON). Figure 30 and Figure 31 compare the efficiency and power loss performance of the CSD87350Q5D versus industry standard MOSFET chipsets commonly used in this type of application. This comparison purely focuses on the efficiency and generated loss of the power semiconductors only. The performance of CSD87350Q5D clearly highlights the importance of considering the Effective AC On-Impedance (ZDS(ON)) during the MOSFET selection process of any new design. Simply normalizing to traditional MOSFET RDS(ON) specifications is not an indicator of the actual in-circuit performance when using TI's Power Block technology. 96 10 93 9 PowerBlock HS/LS RDS(ON) = 5m/2.1m Discrete HS/LS RDS(ON) = 5m/1.2m Discrete HS/LS RDS(ON) = 5m/2.1m 8 87 VGS = 5V VIN = 12V VOUT = 1.3V LOUT = 0.3H fSW = 500kHz TA = 25C 84 81 78 0 5 10 15 20 25 30 Output Current (A) 35 VGS = 5V VIN = 12V VOUT = 1.3V LOUT = 0.3H fSW = 500kHz TA = 25C 7 6 5 4 3 2 PowerBlock HS/LS RDS(ON) = 5m/2.1m Discrete HS/LS RDS(ON) = 5m/2.1m Discrete HS/LS RDS(ON) = 5m/1.2m 75 72 Power Loss (W) Efficiency (%) 90 1 40 45 0 0 5 10 Figure 30. 15 20 25 30 Output Current (A) 35 40 45 Figure 31. The chart below compares the traditional DC measured RDS(ON) of CSD87350Q5D versus its ZDS(ON). This comparison takes into account the improved efficiency associated with TI's patented packaging technology. As such, when comparing TI's Power Block products to individually packaged discrete MOSFETs or dual MOSFETs in a standard package, the in-circuit switching performance of the solution must be considered. In this example, individually packaged discrete MOSFETs or dual MOSFETs in a standard package would need to have DC measured RDS(ON) values that are equivalent to CSD87350Q5D's ZDS(ON) value in order to have the same efficiency performance at full load. Mid to light-load efficiency will still be lower with individually packaged discrete MOSFETs or dual MOSFETs in a standard package. Comparison of RDS(ON) vs. ZDS(ON) Parameter 10 HS Typ LS Max Typ Max Effective AC On-Impedance ZDS(ON) (VGS = 5V) 5 - 1.2 - DC Measured RDS(ON) (VGS = 4.5V) 5 6.8 2.1 2.8 Submit Documentation Feedback Copyright (c) 2011, Texas Instruments Incorporated CSD87350Q5D SLPS288C - MARCH 2011 - REVISED OCTOBER 2011 www.ti.com The CSD87350Q5D NexFETTM power block is an optimized design for synchronous buck applications using 5V gate drive. The Control FET and Sync FET silicon are parametrically tuned to yield the lowest power loss and highest system efficiency. As a result, a new rating method is needed which is tailored towards a more systems centric environment. System level performance curves such as Power Loss, Safe Operating Area, and normalized graphs allow engineers to predict the product performance in the actual application. Power Loss Curves MOSFET centric parameters such as RDS(ON) and Qgd are needed to estimate the loss generated by the devices. In an effort to simplify the design process for engineers, Texas Instruments has provided measured power loss performance curves. Figure 1 plots the power loss of the CSD87350Q5D as a function of load current. This curve is measured by configuring and running the CSD87350Q5D as it would be in the final application (see Figure 32).The measured power loss is the CSD87350Q5D loss and consists of both input conversion loss and gate drive loss. Equation 1 is used to generate the power loss curve. (VIN x IIN) + (VDD x IDD) - (VSW_AVG x IOUT) = Power Loss (1) The power loss curve in Figure 1 is measured at the maximum recommended junction temperatures of 125C under isothermal test conditions. Safe Operating Curves (SOA) The SOA curves in the CSD87350Q5D data sheet provides guidance on the temperature boundaries within an operating system by incorporating the thermal resistance and system power loss. Figure 3 to Figure 5 outline the temperature and airflow conditions required for a given load current. The area under the curve dictates the safe operating area. All the curves are based on measurements made on a PCB design with dimensions of 4" (W) x 3.5" (L) x 0.062" (T) and 6 copper layers of 1 oz. copper thickness Normalized Curves The normalized curves in the CSD87350Q5D data sheet provides guidance on the Power Loss and SOA adjustments based on their application specific needs. These curves show how the power loss and SOA boundaries will adjust for a given set of systems conditions. The primary Y-axis is the normalized change in power loss and the secondary Y-axis is the change is system temperature required in order to comply with the SOA curve. The change in power loss is a multiplier for the Power Loss curve and the change in temperature is subtracted from the SOA curve. Figure 32. Typical Application Copyright (c) 2011, Texas Instruments Incorporated Submit Documentation Feedback 11 CSD87350Q5D SLPS288C - MARCH 2011 - REVISED OCTOBER 2011 www.ti.com Calculating Power Loss and SOA The user can estimate product loss and SOA boundaries by arithmetic means (see Design Example). Though the Power Loss and SOA curves in this data sheet are taken for a specific set of test conditions, the following procedure will outline the steps the user should take to predict product performance for any set of system conditions. Design Example Operating Conditions: * Output Current = 25A * Input Voltage = 7V * Output Voltage = 1V * Switching Frequency = 800kHz * Inductor = 0.2H Calculating Power Loss * * * * * * Power Loss at 25A = 3.5W (Figure 1) Normalized Power Loss for input voltage 1.07 (Figure 7) Normalized Power Loss for output voltage 0.95 (Figure 8) Normalized Power Loss for switching frequency 1.11 (Figure 6) Normalized Power Loss for output inductor 1.07 (Figure 9) Final calculated Power Loss = 3.5W x 1.07 x 0.95 x 1.11 x 1.07 4.23W Calculating SOA Adjustments * * * * * SOA adjustment for input voltage 2C (Figure 7) SOA adjustment for output voltage -1.3C (Figure 8) SOA adjustment for switching frequency 2.8C (Figure 6) SOA adjustment for output inductor 1.6C (Figure 9) Final calculated SOA adjustment = 2 + (-1.3) + 2.8 + 1.6 5.1C In the design example above, the estimated power loss of the CSD87350Q5D would increase to 4.23W. In addition, the maximum allowable board and/or ambient temperature would have to decrease by 5.1C. Figure 33 graphically shows how the SOA curve would be adjusted accordingly. 1. Start by drawing a horizontal line from the application current to the SOA curve. 2. Draw a vertical line from the SOA curve intercept down to the board/ambient temperature. 3. Adjust the SOA board/ambient temperature by subtracting the temperature adjustment value. In the design example, the SOA temperature adjustment yields a reduction in allowable board/ambient temperature of 5.1C. In the event the adjustment value is a negative number, subtracting the negative number would yield an increase in allowable board/ambient temperature. 50 45 Output Current (A) 40 35 30 1 25 20 VIN = 12V VGS = 5V VOUT = 1.3V fSW = 500kHz LOUT = 0.3 H 15 10 5 2 3 0 0 20 40 60 80 100 Board Temperature (C) 120 140 G028 Figure 33. Power Block SOA 12 Submit Documentation Feedback Copyright (c) 2011, Texas Instruments Incorporated CSD87350Q5D SLPS288C - MARCH 2011 - REVISED OCTOBER 2011 www.ti.com RECOMMENDED PCB DESIGN OVERVIEW There are two key system-level parameters that can be addressed with a proper PCB design: Electrical and Thermal performance. Properly optimizing the PCB layout will yield maximum performance in both areas. A brief description on how to address each parameter is provided. Electrical Performance The Power Block has the ability to switch voltages at rates greater than 10kV/s. Special care must be then taken with the PCB layout design and placement of the input capacitors, Driver IC, and output inductor. * The placement of the input capacitors relative to the Power Block's VIN and PGND pins should have the highest priority during the component placement routine. It is critical to minimize these node lengths. As such, ceramic input capacitors need to be placed as close as possible to the VIN and PGND pins (see Figure 34). The example in Figure 34 uses 6x10F ceramic capacitors (TDK Part # C3216X5R1C106KT or equivalent). Notice there are ceramic capacitors on both sides of the board with an appropriate amount of vias interconnecting both layers. In terms of priority of placement next to the Power Block, C5, C7, C19, and C8 should follow in order. * The Driver IC should be placed relatively close to the Power Block Gate pins. TG and BG should connect to the outputs of the Driver IC. The TGR pin serves as the return path of the high-side gate drive circuitry and should be connected to the Phase pin of the IC (sometimes called LX, LL, SW, PH, etc.). The bootstrap capacitor for the Driver IC will also connect to this pin. * The switching node of the output inductor should be placed relatively close to the Power Block VSW pins. Minimizing the node length between these two components will reduce the PCB conduction losses and actually reduce the switching noise level. * In the event the switch node waveform exhibits ringing that reaches undesirable levels, the use of a Boost Resistor or RC snubber can be an effective way to reduce the peak ring level. The recommended Boost Resistor value will range between 1 to 4.7 depending on the output characteristics of Driver IC used in conjunction with the Power Block. The RC snubber values can range from 0.5 to 2.2 for the R and 330pF to 2200pF for the C. Refer to TI App Note SLUP100 for more details on how to properly tune the RC snubber values. The RC snubber should be placed as close as possible to the Vsw node and PGND see Figure 34 (1) (1) Keong W. Kam, David Pommerenke, "EMI Analysis Methods for Synchronous Buck Converter EMI Root Cause Analysis", University of Missouri - Rolla Copyright (c) 2011, Texas Instruments Incorporated Submit Documentation Feedback 13 CSD87350Q5D SLPS288C - MARCH 2011 - REVISED OCTOBER 2011 www.ti.com Thermal Performance The Power Block has the ability to utilize the GND planes as the primary thermal path. As such, the use of thermal vias is an effective way to pull away heat from the device and into the system board. Concerns of solder voids and manufacturability problems can be addressed by the use of three basic tactics to minimize the amount of solder attach that will wick down the via barrel: * Intentionally space out the vias from each other to avoid a cluster of holes in a given area. * Use the smallest drill size allowed in your design. The example in Figure 34 uses vias with a 10 mil drill hole and a 16 mil capture pad. * Tent the opposite side of the via with solder-mask. In the end, the number and drill size of the thermal vias should align with the end user's PCB design rules and manufacturing capabilities. Input Capacitors Input Capacitors TGR TG VIN PGND Output Capacitors Driver IC Power Block BG V SW VSW V SW RC Snubber Power Block Location on Top Layer Top Layer Output Inductor Bottom Layer Figure 34. Recommended PCB Layout (Top Down View) 14 Submit Documentation Feedback Copyright (c) 2011, Texas Instruments Incorporated CSD87350Q5D SLPS288C - MARCH 2011 - REVISED OCTOBER 2011 www.ti.com MECHANICAL DATA Q5D Package Dimensions E2 K d2 c1 4 5 4 q L d1 L 5 E1 6 3 6 3 b 9 D2 2 7 7 D1 2 E e 8 1 8 1 d d3 f Top View Bottom View Side View Pinout Position Exposed Tie Bar May Vary q a c E1 Front View Pin 1 Designation VIN Pin 2 VIN Pin 3 TG Pin 4 TGR Pin 5 BG Pin 6 VSW Pin 7 VSW Pin 8 VSW Pin 9 PGND M0187-01 DIM MILLIMETERS MIN INCHES MAX MIN MAX a 1.40 1.5 0.055 0.059 b 0.360 0.460 0.014 0.018 c 0.150 0.250 0.006 0.010 c1 0.150 0.250 0.006 0.010 d 1.630 1.730 0.064 0.068 d1 0.280 0.380 0.011 0.015 d2 0.200 0.300 0.008 0.012 d3 0.291 0.391 0.012 0.015 D1 4.900 5.100 0.193 0.201 D2 4.269 4.369 0.168 0.172 E 4.900 5.100 0.193 0.201 E1 5.900 6.100 0.232 0.240 E2 3.106 3.206 0.122 e 1.27 TYP 0.126 0.050 f 0.396 0.496 0.016 0.020 L 0.510 0.710 0.020 0.028 0.00 - - - K Copyright (c) 2011, Texas Instruments Incorporated 0.812 0.032 Submit Documentation Feedback 15 CSD87350Q5D SLPS288C - MARCH 2011 - REVISED OCTOBER 2011 www.ti.com Land Pattern Recommendation 3.480 (0.137) 0.530 (0.021) 0.415 (0.016) 0.345 (0.014) 0.650 (0.026) 5 4 0.650 (0.026) 4.460 (0.176) 0.620 (0.024) 0.620 (0.024) 4.460 (0.176) 1.270 (0.050) 1 1.920 (0.076) 8 0.850 (0.033) 0.400 (0.016) 0.850 (0.033) 6.240 (0.246) M0188-01 NOTE: Dimensions are in mm (inches). Text For Spacing Stencil Recommendation 0.250 (0.010) 0.300 (0.012) 0.610 (0.024) 0.341 (0.013) 5 4 0.410 (0.016) Stencil Opening 0.300 (0.012) 0.300 (0.012) 1.710 (0.067) 8 1 1.680 (0.066) 0.950 (0.037) 1.290 (0.051) PCB Pattern M0208-01 NOTE: Dimensions are in mm (inches). Text For Spacing For recommended circuit layout for PCB designs, see application note SLPA005 - Reducing Ringing Through PCB Layout Techniques. 16 Submit Documentation Feedback Copyright (c) 2011, Texas Instruments Incorporated CSD87350Q5D SLPS288C - MARCH 2011 - REVISED OCTOBER 2011 www.ti.com Q5D Tape and Reel Information 4.00 0.10 (See Note 1) K0 0.30 0.05 +0.10 2.00 0.05 O 1.50 -0.00 1.75 0.10 5.50 0.05 12.00 0.30 B0 R 0.20 MAX A0 8.00 0.10 O 1.50 MIN R 0.30 TYP A0 = 5.30 0.10 B0 = 6.50 0.10 K0 = 1.90 0.10 M0191-01 NOTES: 1. 10-sprocket hole-pitch cumulative tolerance 0.2 2. Camber not to exceed 1mm in 100mm, noncumulative over 250mm 3. Material: black static-dissipative polystyrene 4. All dimensions are in mm, unless otherwise specified. 5. Thickness: 0.30 0.05mm 6. MSL1 260C (IR and convection) PbF reflow compatible Spacer REVISION HISTORY Changes from Original (March 2011) to Revision A * Page Changed Power Dissipation, PD in the ABSOLUTE MAXIMUM RATINGS table From; 13 W to 12 W ............................... 2 Changes from Revision A (August 2011) to Revision B Page * Replaced RDS(on) with ZDS(on) ................................................................................................................................................. 3 * Added Equivalent System Performance section ................................................................................................................... 9 * Added the Comparison of RDS(on) vs ZDS(on) table ............................................................................................................... 10 * Added Electrical Performance bullet ................................................................................................................................... 13 Changes from Revision B (September 2011) to Revision C * Page Changed "DIM a" Millimeter Max value From: 1.55 To: 1.5 and Inches Max value From: 0.061 To: 0.059 ...................... 15 Copyright (c) 2011, Texas Instruments Incorporated Submit Documentation Feedback 17 PACKAGE MATERIALS INFORMATION www.ti.com 9-Oct-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device CSD87350Q5D Package Package Pins Type Drawing SON DQY 8 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 12.4 Pack Materials-Page 1 5.3 B0 (mm) K0 (mm) P1 (mm) 6.3 1.8 8.0 W Pin1 (mm) Quadrant 12.0 Q2 PACKAGE MATERIALS INFORMATION www.ti.com 9-Oct-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) CSD87350Q5D SON DQY 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated