TL072 LOW NOISE JFET INPUT OPERATIONAL AMPLIFIERS General Description Features * * * * * Low Power Consumption Wide Common-Mode and Differential Voltage Ranges Low Input Bias and Offset Currents Output Short-Circuit Protection Low Total Harmonic Distortion...0.003% Typ * Low Noise Vn= 18nV * * * * * * High Input Impedance...JFET-Input Stage Internal Frequency Compensation Latch-Up-Free Operation High Slew Rate...13V/s Typ Common-Mode Input Voltage Range Includes VCC+ SOP-8L: Available in "Green" Molding Compound (No Br, Sb) Lead Free Finish/ RoHS Compliant (Note 1) * Typ at f=1kHz The JFET-input operational amplifiers in the TL072 are similar to the TL082, with low input bias and offset currents and fast slew rate. The low harmonic distortion and low noise make the TL072 ideally suited for high-fidelity and audio preamplifier applications. Each amplifier features JFET inputs (for high input impedance) coupled with bipolar output stages integrated on a single monolithic chip. Applications * * Active filters Audio pre-amps Ordering Information TL 072 S G - 13 Device TL072SG-13 Notes: Package Green Packing S : SOP-8L G : Green 13 : Tape & Reel Package Code S Packaging (Note 2) SOP-8L 13" Tape and Reel Quantity Part Number Suffix 2500/Tape & Reel -13 1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at http://www.diodes.com/products/lead_free.html 2. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at http://www.diodes.com/datasheets/ap02001.pdf. TL072 Rev. 1 1 of 11 www.diodes.com MAY 2009 (c) Diodes Incorporated TL072 LOW NOISE JFET INPUT OPERATIONAL AMPLIFIERS Pin Assignments (1) Dual channel SOP-8L ( Top View ) OUTPUT1 1 INVERTING INPUT1 2 NON-INVERTING INPUT1 3 8 VCC+ TL072 VCC- 4 7 OUTPUT2 6 INVERTING INPUT2 5 NON-INVERTING INPUT2 SOP-8L Pin Descriptions Pin Name OUTPUT1 INVERTING INPUT1 NON-INVERTING INPUT1 VCCNON-INVERTING INPUT2 INVERTING INPUT2 OUTPUT2 VCC+ Pin No. 1 2 3 4 5 6 7 8 Description Channel 1 Output Channel 1 Inverting Input Channel 1 Non-inverting Input Supply Voltage Channel 2 Non-inverting Input Channel 2 Inverting Input Channel 2 Ouput Supply Voltage Block Diagram TL072 Rev. 1 2 of 11 www.diodes.com JULY 2009 (c) Diodes Incorporated TL072 LOW NOISE JFET INPUT OPERATIONAL AMPLIFIERS Absolute Maximum Ratings Symbol ESD HBM ESD MM VCC+ VCCVI Notes: (Note 8) Parameter Human Body Model ESD Protection Machine Model ESD Protection Supply Voltage + (Note 3) Supply Voltage - (Note 3) Input voltage (Notes 3 and 5) VID Differential input Voltage, VID (Note 4) PD TJ TST Duration of output short circuit (Note 6) Power Dissipation (Note 7) Operating Junction Temperature Range Storage Temperature Range Unit 1 200 +18 -18 15 KV V V V V 30 Unlimited 860 150 -65 to +150 V mW o C o C 3. ALL voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC-. 4. Differential voltage are at the non-inverting input terminal with respect to the inverting input terminal. 5. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15V, whichever is less. 6. The output may be shorted to ground or either supply. Temperature and/or supply voltage must be limited to ensure that the dissipation rating is not exceeded. 7. Maximum power dissipation is a function of TJ(max), JA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD=(TJ(max)-TA)/ JA . Operating at the absolute maximum TJ of 150 can affect reliability Recommended Operating Conditions Symbol VCC TA Notes: Rating (Note 8) Description Supply Voltage Operating Ambient Temperature Range Rating Unit 15 V -40 to +85 C 8. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Recommended Operating Conditions indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics. TL072 Rev. 1 3 of 11 www.diodes.com JULY 2009 (c) Diodes Incorporated TL072 LOW NOISE JFET INPUT OPERATIONAL AMPLIFIERS Electrical Characteristics Symbol Parameter (VCC = 15V, TA = 25 oC; unless otherwise noted) Test Conditions VO=0, RS=50 VIO Input Offset Voltage Temperature Coefficient VO=0, RS=50, TA= full range of Input Offset Voltage TA=25 oC Input Offset Current VO=0 TA= full range o TA=25 C Input Bias Current VO=0 TA= full range Common Mode Input Voltage Range o RL=10k, TA=25 C Maximum Peak RL10k, Output Voltage Swing TA= full range RL2k vIO IIO IIB VICR VOM Large Signal Differential VO=10V, RL2k Voltage Amplification AVD B1 ri CMRR kSVR ICC VO1/VO2 SR tr Min TA=25 oC TA= full range TA=25 oC TA= full range Unity Gain Bandwidth Input Resistance Common Mode Rejection Ratio Supply Voltage Rejection Ratio (VCC/VIO) Supply Current (each amplifier) Crosstalk Attenuation TA=25 oC VIC=VICRmin, VO=0 RS=50, TA=25 oC VCC=9 to 15V VO=0 RS=50, TA=25 oC VO=0, TA=25 oC No load AVD=100, TA=25 oC V =10V, CL=100pF, RL=2k Slew Rate at Unity Gain I (See Figure 1) Rise Time VI=20mV, RL=2k, CL=100pF (See Figure 1) Overshoot Factor Typ. Max Unit 3 6 8 mV 5 65 11 -12~+15 12 12 13.5 50 25 MHz 75 100 dB 80 100 dB 1.4 8 2.5 mA 120 dB 13 V/s 0.1 20 s % f=1kHz 18 f=10 Hz to 10kHz 4 In RS=20, f=1kHz 0.01 Total Harmonic Distortion VIrms=6V, AVD=1, RL2k, RS1k, f=1kHz 0.003 Notes: V/mV 3 1012 Equivalent Input Noise Current JC V 200 RS=20 Thermal Resistance Junction-to-Ambient Thermal Resistance Junction-to-Case pA nA pA nA V Equivalent Input Noise Voltage JA 100 2 200 20 10 Vn THD V/ oC 18 nV HZ V pA HZ % SOP-8L (Note 9) 145 o C/W SOP-8L (Note 9) 35 o C/W 9. Test condition for SOP-8L: Devices mounted on FR-4 substrate PC board, with minimum recommended pad layout. TL072 Rev. 1 4 of 11 www.diodes.com JULY 2009 (c) Diodes Incorporated TL072 LOW NOISE JFET INPUT OPERATIONAL AMPLIFIERS Typical Performance Characteristics Maximum Peak Output Voltage vs Temperature VOM -Maximum Peak Output Voltage(V) VOM -Maximum Peak Output Voltage(V) Maximum Peak Output Voltage vs Supply Voltage 15.0 RL=10k TA =25 12.5 10.0 7.5 5.0 2.5 15.0 RL=10k 12.5 RL=2k 10.0 7.5 5.0 2.5 VCC=15V See Figure 2 0.00 0.0 0 0 2 4 6 8 10 12 14 16 -50 18 -25 |Vcc| Supply Voltage (V) Maximum Peak Output Voltage vs Load Resistance 25 50 75 100 Maximum Peak Output Voltage vs Frequency 15.0 15.0 VOM -Maximum Peak Output Voltage(V) VOM -Maximum Peak Output Voltage(V) 0 T A-Free Air Temperature ( ) VCC=15V TA =25 See Figure 2 12.5 10.0 7.5 5.0 2.5 0.0 0 0.1 10 0.2 0.4 0.7 100 1 2 4 71000 10 Load Resistance (k) TL072 Rev. 1 VCC=15V RL=10k TA =25 See Figure 2 12.5 10.0 VCC=10V 7.5 5.0 VCC=5V 2.5 0 0.0 100 1k 10k 100k 1M 10M Frequency (Hz) 5 of 11 www.diodes.com JULY 2009 (c) Diodes Incorporated TL072 LOW NOISE JFET INPUT OPERATIONAL AMPLIFIERS Typical Performance Characteristics (Continued) Maximum Peak Output Voltage vs Frequency RL=2k VCC=15V 12.5 TA =25 See Figure 2 10.0 VCC=10V 7.5 5.0 VCC=5V 2.5 0 0.0 100 1k 10k 100k 1M 15.0 VOM -Maximum Peak Output Voltage(V) VOM -Maximum Peak Output Voltage(V) Maximum Peak Output Voltage vs Frequency 15.0 TA =-40 TA =25 10.0 TA =85 7.5 5.0 2.5 0.0 0 10000 10k 10M Frequency (Hz) IIB -Input Bias Current(nA) VCC=15V 10.00 10 1.001 0.10 0.1 0.01 0.01 0 25 50 75 100 AVD -Differential Voltage Amplification (V/mV) 1000.0 1000 100.00 100 -25 TA-Free Air Temperature () TL072 Rev. 1 40k 100000 100k 400k1000000 1M 4M 10000000 10M Frequency (Hz) Input Bias Current vs Temperature -50 VCC=15V RL=2k See Figure 2 12.5 6 of 11 www.diodes.com Large Signal Differential Voltage Amplification vs Temperature 400 200 100 100.0 40 20 10 10.0 VCC=15V 4 VO=10V 2 RL=2k 1.01 -50 -25 0 25 50 75 TA-Free-Air Temperature () 100 JULY 2009 (c) Diodes Incorporated TL072 LOW NOISE JFET INPUT OPERATIONAL AMPLIFIERS Typical Performance Characteristics (Continued) Supply Current vs Temperature 2.0 2.4 1.8 2.2 1.6 ICC -Supply Current(mA) ICC -Supply Current(mA) Supply Current vs Supply Voltage 1.4 1.2 1.0 0.8 0.6 TA =25 No Signal No Load 0.4 0.2 2 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 VCC=15V No Signal No Load 0.2 0 0.0 0 0.0 0 2.0 4 6 8 10 12 14 16 -50 -25 |Vcc| Supply Voltage (V) PD -Total Power Disspation(mW) 150 125 100 75 50 VCC=15V No Signal No Load 0 -50 -25 0 25 50 75 100 TA-Free Air Temperature () TL072 Rev. 1 25 50 75 100 Common Mode Rejection Ratio vs Temperature CMRR -Common-Mode Rejection Ratio(dB) Total Power Dissipation vs Temperature 25 0 TA-Free Air Temperature () 98 VCC=15V 97 RL=10k 96 95 94 93 92 91 90 -50 -25 0 25 50 75 100 TA-Free Air Temperature () 7 of 11 www.diodes.com JULY 2009 (c) Diodes Incorporated TL072 LOW NOISE JFET INPUT OPERATIONAL AMPLIFIERS Typical Performance Characteristics (Continued) Voltage-Follower Large-Singnal Pulse Response 6 50 Input VCC=15V AVD=10 40 Input and Output Voltages(V) Vn - Equivalent Input Noise Voltage(nV/ Hz) Equivalent Input Noise Voltage vs Frequency RS=20 TA =25 30 20 10 0 10 10 VCC=5V RL=2k 4 C L=100pF TA =25 2 0 Output -2 -4 -6 100 40 400 1000 1k 4k 10000 10k 40k 100000 100k -0.5 0 0.5 Frequency (Hz) Total Harmonic Distortion vs Frequency 3 3.5 Overshoot 24 AVD=1 VO -Output Voltage(mV) Total Harmonic Distortion(%) 2.5 28 VCC=15V VI(RMS)=6V 0.1 0.1 1.5 2 t-Time-s Output Voltage vs Elapsed Time 11 0.4 1 TA =25 0.04 0.01 0.01 0.00 20 90 16 12 8 VCC=5V 4 RL=2k 10% TA =25 0 tr 0.001 0.001 100 0.1 TL072 Rev. 1 -4 400 1k 4k 10k 1 10 Frequency(Hz) 40k 100k 100 8 of 11 www.diodes.com -0.1 0 0.1 0.2 0.3 0.4 t-Elapsed Time-s 0.5 0.6 0.7 JULY 2009 (c) Diodes Incorporated TL072 LOW NOISE JFET INPUT OPERATIONAL AMPLIFIERS Test Circuit 10k 1k V OUT V CL=100pF OUT RL=2k RL Figure 1. Unity-Gain Amplifier CL=100pF Figure 2. Gain-of-10 Inverting Amplifier Marking Information (1) SOP-8L ( Top View ) 8 5 Logo Part Number TL072 YY WW X X 1 TL072 Rev. 1 G : Green YY : Year : 08, 09,10~ WW : Week : 01~52; 52 represents 52 and 53 week X : Internal Code 4 9 of 11 www.diodes.com JULY 2009 (c) Diodes Incorporated TL072 LOW NOISE JFET INPUT OPERATIONAL AMPLIFIERS Package Information ( All Dimensions in mm ) 0.254 0.10/0.20 3.85/3.95 5.90/6.10 (1) Package type: SOP-8L Gauge Plane Seating Plane 0.62/0.82 Detail "A" 7~9 0.15/0.25 1.30/1.50 1.75max. 0.35max. 45 7~9 Detail "A" 0/8 0.3/0.5 1.27typ 4.85/4.95 5.4 8x-0.60 8x-1.55 6x-1.27 Land Pattern Recommendation (Unit: mm) TL072 Rev. 1 10 of 11 www.diodes.com JULY 2009 (c) Diodes Incorporated TL072 LOW NOISE JFET INPUT OPERATIONAL AMPLIFIERS IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright (c) 2009, Diodes Incorporated www.diodes.com TL072 Rev. 1 11 of 11 www.diodes.com JULY 2009 (c) Diodes Incorporated