Mini-Circuits - Specification for Amplifier - ERA-5
Amplifier
print this page ERA-5
Frequency
MHz GAIN, dB Maximum Power, dBm Dynamic
Range VSWR Absolute
Maximum
Rating DC Power Thermal
resistance
Øjc
°C/W
fL - fUMin. Output
(1 dB
Comp.) Min. Input
(no
damage)
NF
dB
Typ.
IP3
dBm
Typ.
In
DC-
3
GHz
In
3-fu
GHz
Out
DC-
3
GHz
Out
3-fu
GHz
I
(mA) P
(mW)
Cur-
rent
(mA)
Device
Volt(V.)
DC-4000 16 +18.40 +16.50 +13.00 4.30 32 +1.30 1.30 1.20 1.30 120 650 65 4.90 278
Lw=low range(fL to fU/2) U=upper range(fU/2 to fU)
Pin Connections
Port RF in RF Out DC Case GND Not Used
cb 1 3 3 2,4 -
Case Style - VV105 (inch,mm ) weight: 0.015
grams.
A B C D E F G H J
.085
2.159 .060
1.524 .008
0.203 .020
0.508 .250
6.350 .012
0.305 .025
0.635
K L M N P Q R S T
Tolerance: .x ± .1 .xx ± .03 .xxx ± .015 inch.
Material and Finish:
Case material: plastic. Lead finish: tin-lead plate or
tin plate.
Marking:
RF input lead (1) identified by one or both of the
following at factory option:
(a) diagonally cut lead, which may be
45°(ref) in either direction;
(b) orientation mark on the case. Model
dash number identified by color dot or
alphanumeric code on case. See specification data
sheet.
Special Tolerances:
Notes:
•ERA-SM models available on tape and reel.
•Model number designated by alphanumeric code marking.
•Permanent damage may occur if any of these limits are exceeded. These ratings are not intended for
continuous normal operation.
•For Amplifier Selection Guide, please click here.
For Amplifier Environmental Specifications, please click here.
•For Surface Mount Environmental Specifications, please click here.
Re-flow soldering information is available in "Surface Mount" article.
•Low frequency cutoff determined by external coupling capacitors.
•Gain, VSWR at 2 GHz.
•Maximum Power, NF, IP3 at 1 GHz.
•fU is the upper frequency limit for each model as shown in the table.
•Non-hermetic
•Absolute maximum ratings:
Operating temperature: -45°C to 85°C,
Storage temperature: -65° to 150°C,
Device voltage:
4.2V min., 5.5V max.
•Typical Biasing Configuration ERA/MAR/MAV/RAM/VAM
•Supply voltage must be connected to pin 3 through a bias resistor in order to prevent damage. See
Biasing MMIC Amplifiers. Reliability predictions are applicable at specified current and normal
operating conditions.
•General Quality Control Procedures and Environmental Specifications are given in Mini- Circuits
Guarantees Quality.
Hi-Rel, MIL description are given in Hi-Rel and MIL
•Prices and Specifications subjects to change without notice.
http://www.minicircuits.com/cgi-bin/spec?cat=amplifier&model=ERA-5&pix=vv105.gif&bv=4 (1 of 2) [6/30/2004 5:47:25 PM]
i2 Technologies US, Inc.
HTML Pages converted to PDF Document
This document contain component information from the
manufacturer's website which are not available in a revision
controlled document from the manufacturer. To facilitate the
addition of these parts into the Electronics Database, we are
converting the HTML pages related to that part, from the
manufacturer's website into Adobe PDF format. The contents of this
document is based on the information provided on the
manufacturer's website, therefore the information may have been
changed by the manufacturer since this was created.
Powering the Bottom Line ®
i2 Technologies US, Inc.
15445 Innovation Drive
San Diego, CA 92128
