DGN-8 DGK-8 D-8 THS4211 THS4215 DRB-8 www.ti.com ................................................................................................................................... SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 LOW-DISTORTION, HIGH-SPEED, VOLTAGE FEEDBACK AMPLIFIER Check for Samples: THS4211 THS4215 FEATURES 1 * * * * 23 * * * * * DESCRIPTION Unity-Gain Stability Wide Bandwidth: 1 GHz High Slew Rate: 970 V/s Low Distortion: - -90 dBc THD at 30 MHz - 130-MHz Bandwidth (0.1 dB, G = 2) - 0.007% Differential Gain - 0.003 Differential Phase High Output Drive, IO = 170 mA Excellent Video Performance: - 130-MHz Bandwidth (0.1 dB, G = 2) - 0.007% Differential Gain - 0.003 Differential Phase Supply Voltages - +5 V, 5 V, +12 V, +15 V Power Down Functionality (THS4215) Evaluation Module Available The THS4211 and THS4215 are high slew rate, unity-gain stable, voltage feedback amplifiers designed to run from supply voltages as low as 5 V and as high as 15 V. The THS4215 offers the same performance as the THS4211 with the addition of power-down capability. The combination of high slew rate, wide bandwidth, low distortion, and unity-gain stability make the THS4211 and THS4215 high-performance devices across multiple ac specifications. Designers using the THS4211 are rewarded with higher dynamic range over a wider frequency band without the stability concerns of decompensated amplifiers. These devices are available in SOIC, MSOP with PowerPADTM, and leadless MSOP with PowerPAD packages. RELATED DEVICES DEVICE APPLICATIONS * * * * * High Linearity ADC Preamplifier Differential to Single-Ended Conversion DAC Output Buffer Active Filtering Video Applications DESCRIPTION THS4271 1.4-GHz voltage feedback amplifier THS4503 Wideband, fully differential amplifier THS3202 Dual, wideband current feedback amplifier THS4211 NC ININ+ VS- Low-Distortion, Wideband Application Circuit 7 3 6 4 5 NC VS+ VOUT NC -50 50 Gain = 2 Rf = 392 RL = 150 VO = 2 VPP VS = 5 V -55 49.9 THS4211 _ -5 V 392 392 NOTE: Power supply decoupling capacitors not shown VO Harmonic Distortion - dBc + VI 8 2 HARMONIC DISTORTION vs FREQUENCY +5 V 50 Source 1 -60 -65 -70 -75 -80 HD2 -85 HD3 -90 -95 -100 1 10 f - Frequency - MHz 100 1 2 3 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2002-2009, Texas Instruments Incorporated THS4211 THS4215 SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ................................................................................................................................... www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ABSOLUTE MAXIMUM RATINGS Over operating free-air temperature range (unless otherwise noted). (1) UNIT Supply voltage, VS 16.5 V Input voltage, VI VS Output current, IO 250 mA Continuous power dissipation Maximum junction temperature, TJ See Dissipation Ratings Table (2) +150C Maximum junction temperature, continuous operation, long-term reliability TJ (3) +125C Storage temperature range, Tstg ESD ratings (1) (2) (3) -65C to +150C HBM 4000 V CDM 1500 V MM 200 V Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. The absolute maximum ratings under any condition is limited by the constraints of the silicon process. Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. The maximum junction temperature for continuous operation is limited by package constraints. Operation above this temperature may result in reduced reliability and/or lifetime of the device. PACKAGE DISSIPATION RATINGS (1) (1) (2) (3) POWER RATING (3) PACKAGE JC (C/W) JA (2) (C/W) TA +25C TA= +85C D (8-pin) 38.3 97.5 1.02 W 410 mW DGN (8-pin) (1) 4.7 58.4 1.71 W 685 mW DGK (8-pin) 54.2 260 385 mW 154 mW DRB (8-pin) 5 45.8 2.18 W 873 mW The THS4211/5 may incorporate a PowerPADTM on the underside of the chip. This acts as a heat sink and must be connected to a thermally dissipative plane for proper power dissipation. Failure to do so may result in exceeding the maximum junction temperature which could permanently damage the device. See TI technical briefs SLMA002 and SLMA004 for more information about utilizing the PowerPAD thermally enhanced package. This data was taken using the JEDEC standard High-K test PCB. Power rating is determined with a junction temperature of +125C. This is the point where distortion starts to substantially increase. Thermal management of the final PCB should strive to keep the junction temperature at or below +125C for best performance and long term reliability. RECOMMENDED OPERATING CONDITIONS Supply voltage, (VS+ and VS-) Dual supply Single supply Input common-mode voltage range 2 Submit Documentation Feedback MIN MAX 2.5 7.5 5 15 VS- + 1.2 VS+ - 1.2 UNIT V V Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 THS4211 THS4215 www.ti.com ................................................................................................................................... SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 PACKAGING/ORDERING INFORMATION (1) PACKAGED DEVICES PACKAGE TYPE PACKAGE MARKING SOIC-8 -- MSOP-8 BEJ QFN-8-PP (2) BET MSOP-8-PP (2) BFN SOIC-8 -- MSOP-8 BEZ QFN-8-PP (2) BEU MSOP-8-PP (2) BFQ TRANSPORT MEDIA, QUANTITY Non-power-down THS4211D THS4211DR THS4211DGK THS4211DGKR THS4211DRBT THS4211DRBR THS4211DGN THS4211DGNR Rails, 75 Tape and Reel, 2500 Rails, 100 Tape and Reel, 2500 Tape and Reel, 250 Tape and Reel, 3000 Rails, 80 Tape and Reel, 2500 Power-down THS4215D THS4215DR THS4215DGK THS4215DGKR THS4215DRBT THS4215DRBR THS4215DGN THS4215DGNR (1) (2) Rails, 75 Tape and Reel, 2500 Rails, 100 Tape and Reel, 2500 Tape and Reel, 250 Tape and Reel, 3000 Rails, 80 Tape and Reel, 2500 For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. The PowerPAD is electrically isolated from all other pins. PIN ASSIGNMENTS (TOP VIEW) D, DRB, DGK, DGN THS4211 NC 1 8 NC IN- 2 7 IN+ 3 VS- 4 (TOP VIEW) D, DRB, DGK, DGN THS4215 REF 1 8 PD VS+ IN- 2 7 VS+ 6 VOUT IN+ 3 6 VOUT 5 NC VS- 4 5 NC NC = No Connetion NC = No Connection See Note A. NOTE A: The devices with the power down option defaults to the ON state if no signal is applied to the PD pin. Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 Submit Documentation Feedback 3 THS4211 THS4215 SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ................................................................................................................................... www.ti.com ELECTRICAL CHARACTERISTICS: VS = 5 V At RF = 392 , RL = 499 , and G = +2, unless otherwise noted. TYP OVER TEMPERATURE UNITS MIN/ TYP/ MAX 1 GHz Typ G = -1, POUT = -16 dBm 325 MHz Typ G = 2, POUT = -16 dBm 325 MHz Typ G = 5, POUT = -16 dBm 70 MHz Typ PARAMETER TEST CONDITIONS +25C +25C 0C to +70C -40C to +85C AC PERFORMANCE G = 1, POUT = -7 dBm Small-signal bandwidth G = 10, POUT = -16 dBm 35 MHz Typ 0.1-dB flat bandwidth G = 1, POUT = -7 dBm 70 MHz Typ Gain bandwidth product G > 10, f = 1 MHz 350 MHz Typ Full-power bandwidth G = -1, VO = 2 Vp 77 MHz Typ G = 1, VO = 2 V Step 970 V/s Typ G = -1, VO = 2 V Step 850 V/s Typ 22 ns Typ 55 ns Typ -78 dBc Typ RL = 499 -90 dBc Typ RL = 150 -100 dBc Typ RL = 499 -100 dBc Typ RL = 150 -68 dBc Typ RL = 499 -70 dBc Typ RL = 150 -80 dBc Typ RL = 499 Slew rate Settling time to 0.1% Settling time to 0.01% G = -1, VO = 4 V Step Harmonic distortion RL = 150 2nd-order harmonic distortion G = 1, VO = 1 VPP, f = 30 MHz 3rd-order harmonic distortion Harmonic distortion 2nd-order harmonic distortion G = 2, VO = 2 VPP, f = 30 MHz 3rd-order harmonic distortion -82 dBc Typ 3rd-order intermodulation (IMD3) G = 2, VO = 2 VPP, RL = 150 , f = 70 MHz -53 dBc Typ 3rd-order output intercept (OIP3) G = 2, VO = 2 VPP, RL = 150 , f = 70 MHz 32 dBm Typ 0.007 % Typ 0.003 Typ Differential gain (NTSC, PAL) Differential phase (NTSC, PAL) G = 2, RL = 150 Input voltage noise f = 1 MHz 7 nV/Hz Typ Input current noise f = 10 MHz 4 pAHz Typ VO = 0.3 V, RL = 499 70 65 62 60 dB Min 3 12 14 14 mV Max 40 40 V/C Typ 7 15 18 20 A Max 10 10 nA/C Typ DC PERFORMANCE Open-loop voltage gain (AOL) Input offset voltage Average offset voltage drift Input bias current Average bias current drift VCM = 0 V Input offset current 0.3 6 Average offset current drift 4 Submit Documentation Feedback 7 8 A Max 10 10 nA/C Typ Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 THS4211 THS4215 www.ti.com ................................................................................................................................... SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ELECTRICAL CHARACTERISTICS: VS = 5 V (continued) At RF = 392 , RL = 499 , and G = +2, unless otherwise noted. TYP PARAMETER TEST CONDITIONS OVER TEMPERATURE -40C to +85C UNITS MIN/ TYP/ MAX V Min +25C +25C 0C to +70C 4 3.8 3.7 3.6 52 50 48 INPUT CHARACTERISTICS Common-mode input range Common-mode rejection ratio VCM = 1 V 56 dB Min Input resistance Common-mode 4 M Typ Input capacitance Common-mode/differential 0.3/0.2 pF Typ OUTPUT CHARACTERISTICS Output voltage swing 4.0 3.8 3.7 3.6 V Min Output current (sourcing) 220 200 190 180 mA Min 170 140 130 120 mA Min Typ Output current (sinking) Output impedance RL = 10 f = 1 MHz 0.3 POWER SUPPLY Specified operating voltage 5 7.5 7.5 7.5 V Max Maximum quiescent current 19 22 23 24 mA Max Minimum quiescent current 19 16 15 14 mA Min Power-supply rejection (+PSRR) VS+ = 5.5 V to 4.5 V, VS- = 5 V 64 58 54 54 dB Min Power-supply rejection (-PSRR) VS+ = 5 V, VS- = -5.5 V to -4.5 V 65 60 56 56 dB Min POWER-DOWN CHARACTERISTICS (THS4215 ONLY) REF = 0 V, or VS- Power-down voltage level REF = VS+ or Floating Power-down quiescent current Enable Power-down Enable Power-down REF+1.8 V Min REF+1 V Max REF-1 V Min REF-1.5 V Max PD = Ref +1.0 V, Ref = 0 V 650 850 900 1000 A Max PD = Ref -1.5 V, Ref = 5 V 450 650 800 900 A Max Turn-on time delay(t(ON)) 50% of final supply current value 4 s Typ Turn-off time delay (t(Off)) 50% of final supply current value 3 s Typ 4 G Typ 250 k Typ Input impedance Output impedance f = 1 MHz Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 Submit Documentation Feedback 5 THS4211 THS4215 SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ................................................................................................................................... www.ti.com ELECTRICAL CHARACTERISTICS: VS = 5 V At RF = 392 , RL = 499 , and G = +2, unless otherwise noted. TYP PARAMETER TEST CONDITIONS OVER TEMPERATURE +25C +25C 0C to +70C -40C to +85C UNITS MIN/ TYP/ MAX AC PERFORMANCE Small-signal bandwidth G = 1, POUT = -7 dBm 980 MHz Typ G = -1, POUT = -16 dBm 300 MHz Typ G = 2, POUT = -16 dBm 300 MHz Typ MHz Typ G = 5, POUT = -16 dBm 65 G = 10, POUT = -16 dBm 30 MHz Typ 0.1-dB flat bandwidth G = 1, POUT = -7 dBm 90 MHz Typ Gain bandwidth product G > 10, f = 1 MHz 300 MHz Typ Full-power bandwidth G = -1, VO = 2 Vp 64 MHz Typ G = 1, VO = 2 V Step 800 V/s Typ G = -1, VO = 2 V Step 750 V/s Typ 22 ns Typ 84 ns Typ RL = 150 -60 dBc Typ RL = 499 -60 dBc Typ RL = 150 -68 dBc Typ RL = 499 -68 dBc Typ -70 dBc Typ Slew rate Settling time to 0.1% Settling time to 0.01% G = -1, VO = 2 V Step Harmonic distortion 2nd-order harmonic distortion G = 1, VO = 1 VPP, f = 30 MHz 3rd-order harmonic distortion 3rd-order intermodulation (IMD3) 3rd-order output intercept (OIP3) G = 1, VO = 1 VPP, RL = 150 , f = 70 MHz 34 dBm Typ Input-voltage noise f = 1 MHz 7 nV/Hz Typ Input-current noise f = 10 MHz 4 pA/Hz Typ VO = 0.3 V, RL = 499 68 63 60 60 dB Min 3 12 14 14 mV Max 40 40 V/C Typ 7 15 17 18 A Max 10 10 nA/C Typ 0.3 6 7 8 A Max 10 10 nA/C Typ V Min DC PERFORMANCE Open-loop voltage gain (AOL) Input offset voltage Average offset voltage drift Input bias current Average bias current drift VCM = VS/2 Input offset current Average offset current drift INPUT CHARACTERISTICS Common-mode input range 1/4 1.2/3.8 1.3/3.7 1.4/3.6 50 48 45 Common-mode rejection ratio VCM = 0.5 V, VO = 2.5 V 54 dB Min Input resistance Common-mode 4 M Typ Input capacitance Common-mode/differential 0.3/0.2 pF Typ OUTPUT CHARACTERISTICS Output voltage swing 1/4 1.2/3.8 1.3/3.7 1.4/3.6 V Min Output current (sourcing) 230 210 190 180 mA Min 150 120 100 90 mA Min Typ Output current (sinking) Output impedance 6 RL = 10 f = 1 MHz Submit Documentation Feedback 0.3 Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 THS4211 THS4215 www.ti.com ................................................................................................................................... SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ELECTRICAL CHARACTERISTICS: VS = 5 V (continued) At RF = 392 , RL = 499 , and G = +2, unless otherwise noted. TYP PARAMETER TEST CONDITIONS OVER TEMPERATURE -40C to +85C UNITS MIN/ TYP/ MAX +25C +25C 0C to +70C Specified operating voltage 5 15 15 15 V Max Maximum quiescent current 19 22 23 24 mA Max Minimum quiescent current 19 16 15 14 mA Min POWER SUPPLY Power-supply rejection (+PSRR) VS+ = 5.5 V to 4.5 V, VS- = 0 V 63 58 54 54 dB Min Power-supply rejection (-PSRR) VS+ = 5 V, VS- = -0.5 V to 0.5 V 65 60 56 56 dB Min POWER-DOWN CHARACTERISTICS (THS4215 ONLY) REF = 0 V, or VS- Power-down voltage level REF = VS+ or floating Enable Power down Enable Power down REF+1.8 V Min REF+1 V Max REF-1 V Min REF-1.5 V Max Power-down quiescent current PD = Ref +1.0 V, Ref = 0 V 450 650 750 850 A Max Power-down quiescent current PD = Ref -1.5 V, Ref = 5 V 400 650 750 850 Turn-on-time delay(t(ON)) Turn-off-time delay (t(Off)) 50% of final value Input impedance Output impedance f = 1 MHz A Max 4 s Typ 3 s Typ 6 G Typ 75 k Typ Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 Submit Documentation Feedback 7 THS4211 THS4215 SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ................................................................................................................................... www.ti.com TYPICAL CHARACTERISTICS Table of Graphs (5 V) FIGURE Small-signal unity-gain frequency response 1 Small-signal frequency response 2 0.1-dB gain flatness frequency response 3 Large-signal frequency response 4 Slew rate vs Output voltage 5 Harmonic distortion vs Frequency Harmonic distortion vs Output voltage swing Third-order intermodulation distortion vs Frequency 14, 16 Third-order output intercept point vs Frequency 15, 17 Voltage and current noise vs Frequency 18 Differential gain vs Number of loads 19 Differential phase vs Number of loads 20 6, 7, 8, 9 10, 11, 12, 13 Settling time 21 Quiescent current vs supply voltage 22 Output voltage vs Load resistance 23 Frequency response vs Capacitive load 24 Open-loop gain and phase vs Frequency 25 Open-loop gain vs Case temperature 26 Rejection ratios vs Frequency 27 Rejection ratios vs Case temperature 28 Common-mode rejection ratio vs Input common-mode range 29 Input offset voltage vs Case temperature 30 Input bias and offset current vs Case temperature 31 Small-signal transient response 32 Large-signal transient response 33 Overdrive recovery 34 Closed-loop output impedance vs Frequency 35 Power-down quiescent current vs Supply voltage 36 Power-down output impedance vs Frequency 37 Turn-on and turn-off delay times 8 Submit Documentation Feedback 38 Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 THS4211 THS4215 www.ti.com ................................................................................................................................... SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 Table of Graphs (5 V) FIGURE Small-signal unity-gain frequency response 39 Small-signal frequency response 40 0.1-dB gain flatness frequency response 41 Large-signal frequency response 42 Slew rate vs Output voltage Harmonic distortion vs Frequency 44, 45, 46, 47 Harmonic distortion vs Output voltage swing 48, 49, 50, 51 Third-order intermodulation distortion vs Frequency 52, 54 Third-order intercept point vs Frequency 53, 55 Voltage and current noise vs Frequency 56 Settling time 43 57 Quiescent current vs Supply voltage 58 Output voltage vs Load resistance 59 Frequency response vs Capacitive load 60 Open-loop gain and phase vs Frequency 61 Open-loop gain vs Case temperature 62 Rejection ratios vs Frequency 63 Rejection ratios vs Case temperature 64 Common-mode rejection ratio vs Input common-mode range 65 Input offset voltage vs Case temperature 66 Input bias and offset current vs Case temperature 67 Small-signal transient response 68 Large-signal transient response 69 Overdrive recovery 70 Closed-loop output impedance vs Frequency 71 Power-down quiescent current vs Supply voltage 72 Power-down output impedance vs Frequency 73 Turn-on and turn-off delay times 74 Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 Submit Documentation Feedback 9 THS4211 THS4215 SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ................................................................................................................................... www.ti.com TYPICAL CHARACTERISTICS: 5 V SMALL-SIGNAL UNITY GAIN FREQUENCY RESPONSE SMALL-SIGNAL FREQUENCY RESPONSE 22 Gain = 1 RL = 499 VO = 250 mV VS = 5 V 3 0.1 20 2 1 0 -1 -2 0 Gain = 10 18 Small Signal Gain - dB 4 -0.1 16 Small Signal Gain - dB 5 Small Signal Gain - dB 0.1-dB GAIN FLATNESS FREQUENCY RESPONSE Gain = 5 14 RL = 499 Rf = 392 VO = 250 mV VS = 5 V 12 10 8 6 Gain = 2 4 2 -4 100 k 1M 10 M 100 M 1G Gain = -1 -2 -4 100 k 1M 10 G f - Frequency - Hz -0.6 -0.7 Gain = 1 RL = 499 VO = 250 mV VS = 5 V 10 M 100 M f - Frequency - Hz -1 1M 1G 10 M 100 M f - Frequency - Hz Figure 2. Figure 3. LARGE-SIGNAL FREQUENCY RESPONSE SLEW RATE vs OUTPUT VOLTAGE HARMONIC DISTORTION vs FREQUENCY 1400 -1 -2 Gain = 1 RL = 499 VO = 2 VPP VS = 5 V -4 100 k Fall, Gain = 1 1000 800 Fall, Gain =- 1 Rise, Gain = -1 600 400 RL = 499 Rf = 392 VS = 5 V 200 10 M 100 M 1G 0 f - Frequency - Hz -60 -90 0.5 1 1.5 2 2.5 3 3.5 4 4.5 1 5 HARMONIC DISTORTION vs FREQUENCY HARMONIC DISTORTION vs FREQUENCY HARMONIC DISTORTION vs FREQUENCY Gain = 2 Rf = 392 VO = 1 VPP VS = 5 V -60 -80 -85 -90 -65 -70 HD3, RL = 150, and RL = 499 -75 -80 HD2, RL = 499 -85 HD2, RL = 150 -90 -60 -65 -70 HD2, RL = 499 -75 -90 -95 -100 -100 10 100 HD3, RL = 150, and RL = 499 -85 -100 1 HD2, RL = 150 -80 -95 100 Gain = 2 Rf = 392 VO = 2 VPP VS = 5 V -55 -95 10 1 10 f - Frequency - MHz f - Frequency - MHz f - Frequency - MHz Figure 7. Figure 8. Figure 9. Submit Documentation Feedback 100 -50 -55 HD3, RL = 150 and RL = 499 HD2, RL = 150 1 10 f - Frequency - MHz Figure 6. HD2, RL = 499 -75 HD2, RL = 499 -85 Figure 5. -65 -70 HD2, RL = 150 -80 Figure 4. Gain = 1 VO = 2 VPP VS = 5 V -55 -75 VO - Output Voltage - V Harmonic Distortion - dBc -50 HD3, RL = 150 and RL = 499 -100 0 1M -70 -95 Harmonic Distortion - dBc -3 Gain = 1 VO = 1 VPP VS = 5 V -65 Harmonic Distortion - dBc SR - Slew Rate - V/ s 0 1G -60 1200 Large Signal Gain - dB -0.5 -0.9 Rise, Gain = 1 Harmonic Distortion - dBc -0.4 Figure 1. 1 10 -0.3 -0.8 0 -3 -0.2 100 Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 THS4211 THS4215 www.ti.com ................................................................................................................................... SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 TYPICAL CHARACTERISTICS: 5 V (continued) HARMONIC DISTORTION vs OUTPUT VOLTAGE SWING -85 -90 HD2, RL = 499 -95 -65 HD2, RL = 499 -70 HD2, RL = 150 -75 -80 -85 -90 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 HD3, RL = 499 HD2, RL = 150 -90 -100 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 0 0.5 1 VO - Output Voltage Swing - V 1.5 2 2.5 3 3.5 4 Figure 12. HARMONIC DISTORTION vs OUTPUT VOLTAGE SWING THIRD-ORDER INTERMODULATION DISTORTION vs FREQUENCY THIRD-ORDER OUTPUT INTERCEPT POINT vs FREQUENCY -50 -55 HD3, RL = 150 HD3, RL = 499 -60 HD2, RL = 499 -65 -70 -75 -80 HD2, RL = 150 -85 -90 -95 -100 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 60 -45 Third-Order Output Intersept Point - dBm Gain = 2 Rf = 249 f = 32 MHz VS = 5 V Third-Order Intermodulation Distortion - dBc Figure 11. -45 Gain = 1 RL = 150 VS = 5 V 200 kHz Tone Spacing -50 -55 -60 -65 -70 VO = 2 VPP -75 -80 -85 -90 -95 -100 4.5 5 VO - Output Voltage Swing - V Figure 10. -40 VO = 1 VPP 10 55 50 45 VO = 1 VPP 40 VO = 2 VPP 35 30 0 100 VO - Output Voltage Swing - V Gain = 1 RL = 150 VS = 5 V 200 kHz Tone Spacing 20 40 60 80 100 f - Frequency - MHz f - Frequency - MHz Figure 13. Figure 14. Figure 15. THIRD-ORDER INTERMODULATION DISTORTION vs FREQUENCY THIRD-ORDER OUTPUT INTERCEPT POINT vs FREQUENCY VOLTAGE AND CURRENT NOISE vs FREQUENCY 100 -55 -60 -65 -70 VO = 2 VPP -75 -80 -85 -90 VO = 1 VPP -95 -100 10 100 Gain = 2 RL = 150 VS = 5 V 200 kHz Tone Spacing 55 50 45 35 VO = 2 VPP 30 In 1 20 20 40 60 80 100 f - Frequency - MHz Figure 16. 10 25 0 f - Frequency - MHz Vn 10 VO = 1 VPP 40 100 Hz -50 Third-Order Output Intersept Point - dBm 60 Gain = 2 RL = 150 VS = 5 V 200 kHz Tone Spacing -45 Hz -40 nV/ Harmonic Distortion - dBc -85 HD3, RL = 499 VO - Output Voltage Swing - V Third-Order Intermodulation Distortion - dBc HD3, RL = 150 -80 -100 0 HD2, RL = 499 -95 -95 -100 -75 I n - Current Noise - pA/ HD2, RL = 150 -60 Gain = 2 Rf = 249 f = 8 MHz VS = 5 V -70 HD3, RL = 150 Harmonic Distortion - dBc HD3, RL = 150 HD3, RL = 499 -80 -65 Gain = 1 f= 32 MHz VS = 5 V -55 Vn - Voltage Noise - Harmonic Distortion - dBc -75 HARMONIC DISTORTION vs OUTPUT VOLTAGE SWING -50 Gain = 1 f= 8 MHz VS = 5 V Harmonic Distortion - dBc -70 HARMONIC DISTORTION vs OUTPUT VOLTAGE SWING Figure 17. Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 1k 10 k 100 k 1M 10 M 1 100 M f - Frequency - Hz Figure 18. Submit Documentation Feedback 11 THS4211 THS4215 SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ................................................................................................................................... www.ti.com TYPICAL CHARACTERISTICS: 5 V (continued) DIFFERENTIAL GAIN vs NUMBER OF LOADS DIFFERENTIAL PHASE vs NUMBER OF LOADS 0.030 0.015 Differential Phase - 0.020 Gain = 2 Rf = 392 VS = 5 V 40 IRE - NTSC and Pal Worst Case 100 IRE Ramp 0.18 PAL NTSC 0.010 0.16 0.14 2 VO - Output Voltage - V Gain = 2 Rf = 392 VS = 5 V 40 IRE - NTSC and Pal Worst Case 100 IRE Ramp 0.025 Differential Gain - % SETTLING TIME 3 0.20 0.12 0.10 PAL 0.08 0.06 NTSC 0.04 0.005 Rising Edge 1 -1 Gain = -1 RL = 499 Rf = 392 f= 1 MHz VS = 5 V -2 Falling Edge 0 0.02 0 0 0 1 2 3 4 5 6 7 8 0 2 3 4 5 6 7 -3 8 10 15 20 Figure 21. QUIESCENT CURRENT vs SUPPLY VOLTAGE OUTPUT VOLTAGE vs LOAD RESISTANCE FREQUENCY RESPONSE vs CAPACITIVE LOAD TA = 85C TA = 25C 1 4 0.5 14 12 Normalized Gain - dB VO - Output Voltage - V TA = -40C 16 5 3 18 2 1 TA = -40 to 85C 0 -1 -2 3 3.5 4 4.5 10 5 0 -0.5 R(ISO) = 15 CL = 50 pF -1 -1.5 R(ISO) = 25 CL = 10 pF -2 -2.5 -5 2.5 VS =5 V R(ISO) = 10 CL = 100 pF -3 -4 10 100 -3 100 k 1000 RL - Load Resistance - VS - Supply Voltage - V 1M 10 M 100 M Figure 23. Figure 24. OPEN-LOOP GAIN AND PHASE vs FREQUENCY OPEN-LOOP GAIN vs CASE TEMPERATURE REJECTION RATIOS vs FREQUENCY 70 90 180 70 160 TA = 25C 50 120 40 100 30 80 20 60 10 40 0 20 Open-Loop Gain - dB 140 Phase - 85 60 100 k 1M 10 M 100 M 0 1G f - Frequency - Hz Figure 25. Submit Documentation Feedback PSRR- TA = 85C 80 75 TA = -40C 70 65 -10 10 k VS = 5 V 60 Rejection Ratios - dB VS = 5 V 1G Capacitive Load - Hz Figure 22. 80 25 t - Time - ns Figure 20. 20 Open-Loop Gain - dB 5 Figure 19. 22 12 0 Number of Loads - 150 Number of Loads - 150 Quiescent Current - mA 1 50 CMRR 40 30 PSRR+ 20 10 60 2.5 3 3.5 4 4.5 5 0 100 k 1M 10 M Case Temperature - C f - Frequency - Hz Figure 26. Figure 27. 100 M 1G Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 THS4211 THS4215 www.ti.com ................................................................................................................................... SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 TYPICAL CHARACTERISTICS: 5 V (continued) COMMON-MODE REJECTION RATIO vs INPUT COMMON-MODE RANGE VS = 5 V PSRR- 70 CMMR PSRR+ 40 30 20 10 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 9 55 8 50 45 40 35 30 25 20 15 10 VS = 5 V TA = 25C 5 0 -4.5 -3 Case Temperature - C 1 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 4.5 TC - Case Temperature - C LARGE-SIGNAL TRANSIENT RESPONSE 0.65 0.6 0.55 IIB- 0.5 IOS 0.45 0.4 0.35 IIB+ 5.8 0.3 5.7 0.25 VO - Output Voltage - V 0.7 VS = 5 V I OS - Input Offset Current - A I IB - Input Bias Current - A 2 Input Common-Mode Range - V 0.12 0.1 1.5 0.08 1 0.06 0.04 0.02 0 -0.02 Gain = -1 RL = 499 Rf =392 tr/tf = 300 ps VS = 5 V -0.04 -0.06 -0.08 -0.1 0.2 -40 -30 -20-10 0 10 20 30 40 50 60 70 80 90 0.5 0 Gain = -1 RL = 499 Rf = 392 tr/tf = 300 ps VS = 5 V -0.5 -1 -1.5 -0.12 -1 TC - Case Temperature - C 0 1 2 3 4 5 6 t - Time - ns 7 8 9 -2 10 0 2 4 6 8 10 12 14 16 18 20 t - Time - ns Figure 31. Figure 32. Figure 33. OVERDRIVE RECOVERY CLOSED-LOOP OUTPUT IMPEDANCE vs FREQUENCY POWER-DOWN QUIESCENT CURRENT vs SUPPLY VOLTAGE 100 k 2.5 4 2 3 1.5 2 1 1 0.5 0 0 -1 -0.5 -2 -1 -3 -1.5 -4 -2 -5 -2.5 -6 -3 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Closed-Loop Output Impedance - 3 VS = 5 V VI - Input Voltage - V Single-Ended Output Voltage - V 3 SMALL-SIGNAL TRANSIENT RESPONSE 6 6 5 VS = 5 V 4 INPUT BIAS AND OFFSET CURRENT vs CASE TEMPERATURE 6.1 5.6 3 5 Figure 30. 6.2 5.9 1.5 VS = 5 V 6 Figure 29. 6.4 6.3 0 7 Figure 28. 6.6 6.5 -1.5 VO - Output Voltage - V 50 60 10 k 1k 100 10 1 0.1 0.01 100 k 1 t - Time - s Figure 34. 800 RL = 499 , RF = 392 , PIN = -4 dBm VS = 5 V Power-Down Quiescent Current - A Rejection Ratios - dB 60 CMRR - Common-Mode Rejection Ratio - dB 80 INPUT OFFSET VOLTAGE vs CASE TEMPERATURE VOS - Input Offset Voltage - mV REJECTION RATIOS vs CASE TEMPERATURE TA = 85C 700 600 500 TA = 25C 400 TA = -40C 300 200 100 0 1M 10 M 100 M f - Frequency - Hz 1G Figure 35. Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 2.5 3 3.5 4 4.5 VS - Supply Voltage - V 5 Figure 36. Submit Documentation Feedback 13 THS4211 THS4215 SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ................................................................................................................................... www.ti.com TYPICAL CHARACTERISTICS: 5 V (continued) POWER-DOWN OUTPUT IMPEDANCE vs FREQUENCY 1000 0.1 1M 10 M 100 M 1G 4.5 0.03 10 0.001 100 k 6 0.035 VO - Output Voltage Level - V Power-Down Output Impedance - 0.04 Gain = 1 RL = 499 PIN = -1 dBm VS = 5 V 3 1.5 0.025 0.02 0 0.015 0.01 -3 -4.5 0.005 -6 0 -7.5 -0.005 -0.01 10 G -1.5 Gain = -1 RL = 499 VS = 5 V V I - Input Voltage Level - V TURN-ON AND TURN-OFF TIMES DELAY TIME 0 f - Frequency - Hz 0.01 0.02 0.03 0.04 0.05 0.06 0.07 t - Time - ns Figure 37. Figure 38. TYPICAL CHARACTERISTICS: 5 V SMALL-SIGNAL UNITY GAIN FREQUENCY RESPONSE SMALL-SIGNAL FREQUENCY RESPONSE 22 Gain = 1 RL = 499 VO = 250 mV VS = 5 V 2 0 -1 -2 10 M 100 M 1G 16 Gain = 5 14 RL = 499 Rf = 392 VO = 250 mV VS = 5 V 12 10 8 6 Gain = 2 4 2 0 Gain = -1 -2 -4 100 k 1M -3 1M 10 G f - Frequency - Hz -0.3 -0.4 -0.5 -0.6 Gain = 1 RL = 499 VO = 250 mV VS = 5 V -0.7 -0.8 -0.9 -1 10 M 100 M f - Frequency - Hz 1G 1M 10 M 100 M f - Frequency - Hz Figure 40. Figure 41. LARGE-SIGNAL FREQUENCY RESPONSE SLEW RATE vs OUTPUT VOLTAGE HARMONIC DISTORTION vs FREQUENCY 1000 -1 -2 Gain = 1 RL = 499 VO = 2 VPP VS = 5 V -4 100 K 800 Rise, G = 1 700 600 Rise, G = -1 500 Fall, G = -1 400 300 RL = 499 Rf = 392 VS = 5 V 200 100 10 M 100 M 1G f - Frequency - Hz Figure 42. Submit Documentation Feedback -60 -65 -70 HD2 -75 -80 HD3 -85 -90 -95 0 1M Gain = 1 VO = 1 VPP RL = 150 , and 499 VS = 5 V -55 Harmonic Distortion - dBc SR - Slew Rate - V/ s 0 1G -50 Fall, G = 1 900 Large Signal Gain - dB -0.2 Figure 39. 1 14 0 -0.1 Gain = 10 18 1 -4 100 k 0.1 20 Small Signal Gain - dB Small Signal Gain - dB 3 Small Signal Gain - dB 4 -3 0.1-dB GAIN FLATNESS FREQUENCY RESPONSE -100 0.4 0.6 0.8 1 1.2 1.4 1.6 VO - Output Voltage -V 1.8 2 Figure 43. 1 10 f - Frequency - MHz 100 Figure 44. Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 THS4211 THS4215 www.ti.com ................................................................................................................................... SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 TYPICAL CHARACTERISTICS: 5 V (continued) HARMONIC DISTORTION vs FREQUENCY HARMONIC DISTORTION vs FREQUENCY -60 HD3 -65 HD2 -70 -75 -80 -30 -50 -40 -60 HD2 -70 HD3 -80 Gain = 2 VO = 1 VPP Rf = 392 RL = 150 and 499 VS = 5 V -90 -85 -100 -90 10 1 100 1 f - Frequency - MHz HD3 -60 -70 Gain = 2 VO = 2 VPP Rf = 392 RL = 150 and 499 VS = 5 V -80 -90 100 1 10 f - Frequency - MHz 100 Figure 47. HARMONIC DISTORTION vs FREQUENCY HARMONIC DISTORTION vs OUTPUT VOLTAGE SWING HARMONIC DISTORTION vs OUTPUT VOLTAGE SWING Harmonic Distortion - dBc HD2 -70 -75 HD3 -80 -85 Gain = 1 RL = 150 , and 499 , f = 8 MHz VS = 5 V -90 -95 -100 -45 -50 -50 -55 -55 HD2 -60 -65 HD3 -70 -75 Gain = 1 RL = 150 , and 499 , f = 32 MHz VS = 5 V -80 -85 -90 0.5 1 1.5 2 VO - Output Voltage Swing - V 2.5 0 0.5 1 1.5 2 VO - Output Voltage Swing - V HD2 -60 -65 HD3 -70 -75 -80 Gain = 2 Rf = 392 RL = 150 and 499 f = 8 MHz VS = 5 V -85 -90 -95 -100 0 2.5 0.5 1 1.5 2 2.5 VO - Output Voltage Swing - V Figure 48. Figure 49. Figure 50. HARMONIC DISTORTION vs OUTPUT VOLTAGE SWING THIRD-ORDER INTERMODULATION DISTORTION vs FREQUENCY THIRD-ORDER OUTPUT INTERCEPT POINT vs FREQUENCY -40 -45 HD2 -50 -55 HD3 -60 -65 Gain = 2 Rf = 392 RL = 150 and 499 f = 32 MHz VS = 5 V -70 -75 -80 0 0.5 1 1.5 2 2.5 Third-Order Intermodulation Distortion - dBc Harmonic Distortion - dBc HD2 Figure 46. -65 0 -50 Figure 45. -60 Harmonic Distortion - dBc 10 f - Frequency - MHz Harmonic Distortion - dBc -55 -40 -40 50 Gain = 1 RL = 150 VS = 5 V 200 kHz Tone Spacing -45 -50 -55 -60 -65 VO = 2VPP -70 -75 -80 -85 VO = 1VPP -90 -95 -100 10 VO - Output Voltage Swing - V Third-Order Output Intersept Point - dBm Harmonic Distortion - dBc -50 Harmonic Distortion - dBc Gain = 1 VO = 2 VPP RL = 150 , and 499 VS = 5 V -45 Harmonic Distortion - dBc -40 HARMONIC DISTORTION vs FREQUENCY 100 f - Frequency - MHz Figure 51. Figure 52. Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 Gain = 1 RL = 150 VS = 5 V 200 kHz Tone Spacing 45 VO = 1VPP 40 VO = 2VPP 35 30 0 10 20 30 40 50 60 70 80 f - Frequency - MHz Figure 53. Submit Documentation Feedback 15 THS4211 THS4215 SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ................................................................................................................................... www.ti.com TYPICAL CHARACTERISTICS: 5 V (continued) THIRD-ORDER OUTPUT INTERCEPT POINT vs FREQUENCY VOLTAGE AND CURRENT NOISE vs FREQUENCY 100 -60 VO = 2 VPP -70 -80 VO = 1 VPP -90 -100 10 100 40 35 Hz nV/ -50 45 VO = 1 VPP 30 Vn 10 VO = 2 VPP 25 20 10 In 15 0 20 40 60 80 1k 100 10 k 100 k 1M 10 M f - Frequency - Hz f - Frequency - MHz Figure 54. Figure 55. Figure 56. SETTLING TIME QUIESCENT CURRENT vs SUPPLY VOLTAGE OUTPUT VOLTAGE vs LOAD RESISTANCE 1.5 2 22 Rising Edge -0.5 18 TA = -40C 16 14 Falling Edge -1 VO - Output Voltage - V Gain = -1 RL = 499 Rf = 392 f= 1 MHz VS = 5 V 0 TA = 25C Quiescent Current - mA 0.5 1.5 TA = 85C 20 1 1 100 M 1 10 f - Frequency - MHz VO - Output Voltage - V 100 Vn - Voltage Noise - -40 Gain = 2 RL = 150 VS = 5 V 200 kHz Tone Spacing Hz 50 Gain = 1 RL = 150 VS = 5 V 200 kHz Tone Spacing I n - Current Noise - pA/ -30 Third-Order Output Intersept Point - dBm Third-Order Intermodulation Distortion - dBc THIRD-ORDER INTERMODULATION DISTORTION vs FREQUENCY 1 0.5 TA = -40 to 85C 0 -0.5 -1 12 -1.5 10 -1.5 0 5 10 15 t - Time - ns 20 3.5 4 4.5 5 10 100 RL - Load Resistance - Figure 57. Figure 58. Figure 59. FREQUENCY RESPONSE vs CAPACITIVE LOAD OPEN-LOOP GAIN AND PHASE vs FREQUENCY OPEN-LOOP GAIN vs CASE TEMPERATURE 80 R(ISO) = 25 , CL = 10 pF 70 -1 R(ISO) = 10 CL = 100 pF -2 140 50 120 40 100 30 80 20 60 10 40 0 20 Open-Loop Gain - dB Open-Loop Gain - dB R(ISO) = 15 CL = 50 pF -1.5 TA = 25C 85 0 -0.5 160 60 1000 90 180 VS = 5 V Phase - 0.5 Normalized Gain - dB 3 VS - Supply Voltage - V 1 TA = 85C 80 75 TA = -40C 70 65 -2.5 VS = 5 V -3 100 k 1M 10 M 100 M Capacitive Load - Hz Figure 60. 16 -2 2.5 25 Submit Documentation Feedback 1G -10 10 k 100 k 1M 10 M 100 M 60 0 1G 2.5 3 3.5 4 4.5 5 Case Temperature - C f - Frequency - Hz Figure 61. Figure 62. Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 THS4211 THS4215 www.ti.com ................................................................................................................................... SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 TYPICAL CHARACTERISTICS: 5 V (continued) REJECTION RATIOS vs CASE TEMPERATURE 80 70 VS = 5 V 50 CMRR 40 30 PSRR+ 20 PSRR- 60 Rejection Ratios - dB 50 CMMR PSRR+ 40 30 20 10 10 0 100 k 1M 10 M 100 M 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 1G 50 45 40 35 30 25 20 15 10 5 0 0 1 2 3 4 Input Common-Mode Voltage Range - V Figure 64. Figure 65. INPUT OFFSET VOLTAGE vs CASE TEMPERATURE INPUT BIAS AND OFFSET CURRENT vs CASE TEMPERATURE SMALL-SIGNAL TRANSIENT RESPONSE VS = 5 V 6 5 VS = 5 V 4 3 2 0.65 6.4 6.3 0.6 IIB- 0.55 6.2 6.1 0.5 0.45 IIB+ 6 0.4 5.9 0.35 IOS 5.8 0.3 5.7 1 LARGE-SIGNAL TRANSIENT RESPONSE -1 -1.5 0 2 4 6 -0.02 -0.06 -1 3 4 5 6 t - Time - ns 7 OVERDRIVE RECOVERY 2 1 1 0.5 0 0 -2 -1 -3 -1.5 100 k 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 t - Time - s Figure 69. 2 CLOSED-LOOP OUTPUT IMPEDANCE vs FREQUENCY 1.5 0 1 Figure 68. -0.5 8 10 12 14 16 18 20 0 Figure 67. -1 t - Time - ns Gain = -1 RL = 499 Rf =392 tr/tf = 300 ps VS = 5 V -0.04 -0.1 VI - Input Voltage - V Single-Ended Output Voltage - V Gain = -1 RL = 499 Rf = 392 tr/tf = 300 ps VS = 5 V -0.5 0.02 0 -0.12 VS = 5 V 0 0.04 -0.08 0.25 3 1.5 0.5 0.06 TC - Case Temperature - C Figure 66. 1 0.08 0.2 5.6 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 TC - Case Temperature - C 5 0.12 0.1 Figure 70. Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 Closed-Loop Output Impedance - 7 0.7 VS = 5 V VO - Output Voltage - V 6.5 I IB - Input Bias Current - A 6.6 8 0 -40 -30-20 -10 0 10 20 30 40 50 60 70 80 90 VO - Output Voltage - V VS = 5 V 55 Figure 63. 9 -2 60 Case Temperature - C f - Frequency - Hz I OS - Input Offset Current - A Rejection Ratios - dB VS = 5 V 70 PSRR- 60 VOS - Input Offset Voltage - mV COMMON-MODE REJECTION RATIO vs INPUT COMMON-MODE RANGE CMRR - Common-Mode Rejection Ratio - dB REJECTION RATIOS vs FREQUENCY 10 k 1k 8 9 10 RL = 499 , RF = 392 , PIN = -4 dBm VS = 5 V 100 10 1 0.1 0.01 100 k 1M 10 M 100 M f - Frequency - Hz 1G Figure 71. Submit Documentation Feedback 17 THS4211 THS4215 SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ................................................................................................................................... www.ti.com TYPICAL CHARACTERISTICS: 5 V (continued) POWER-DOWN OUTPUT IMPEDANCE vs FREQUENCY 1000 TA = 85C 600 500 TA = 25C 400 TA = -40C 300 200 100 0 2.5 3 3.5 4 4.5 VS - Supply Voltage - V Figure 72. Submit Documentation Feedback 5 0.035 Gain = 1 RL = 499 PIN = -1 dBm VS = 5 V 0.03 10 0.1 0.001 100 k 10 M 100 M f - Frequency - Hz 1G 3 10 G Figure 73. 1.5 0 0.02 0.015 -1.5 -3 0.01 Gain = -1 RL = 499 VS = 5 V 0.005 0 -0.005 -0.01 1M 4.5 0.025 VO - Output Voltage Level - V 700 Power-Down Output Impedance - Power-Down Quiescent Current - A 800 18 TURN-ON AND TURN-OFF TIMES DELAY TIME 0 V I - Input Voltage Level - V POWER-DOWN QUIESCENT CURRENT vs SUPPLY VOLTAGE -4.5 -6 -7.5 0.01 0.02 0.03 0.04 0.05 0.06 0.07 t - Time - ns Figure 74. Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 THS4211 THS4215 www.ti.com ................................................................................................................................... SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 APPLICATION INFORMATION HIGH-SPEED OPERATIONAL AMPLIFIERS WIDEBAND, NONINVERTING OPERATION The THS4211 and the THS4215 operational amplifiers set new performance levels, combining low distortion, high slew rates, low noise, and a unity-gain bandwidth in excess of 1 GHz. To achieve the full performance of the amplifier, careful attention must be paid to printed-circuit board (PCB) layout and component selection. The THS4211 and the THS4215 are unity-gain stable, 1-GHz voltage-feedback operational amplifiers, with and without power-down capability, designed to operate from a single 5-V to 15-V power supply. The THS4215 provides a power-down mode, providing the ability to save power when the amplifier is inactive. A reference pin is provided to allow the user the flexibility to control the threshold levels of the power-down control pin. Applications Section Contents * * * * * * * * * * * * * * * * * * Wideband, Noninverting Operation Wideband, Inverting Gain Operation Single-Supply Operation Saving Power with Power-Down Functionality and Setting Threshold Levels with the Reference Pin Power Supply Decoupling Techniques and Recommendations Using the THS4211 as a DAC Output Buffer Driving an ADC with the THS4211 Active Filtering with the THS4211 Building a Low-Noise Receiver with the THS4211 Linearity: Definitions, Terminology, Circuit Techniques and Design Tradeoffs An Abbreviated Analysis of Noise in Amplifiers Driving Capacitive Loads Printed-Circuit Board Layout Techniques for Optimal Performance Power Dissipation and Thermal Considerations Performance vs Package Options Evaluation Fixtures, Spice Models, and Applications Support Additional Reference Material Mechanical Package Drawings Figure 75 shows the noninverting gain configuration of 2 V/V used to demonstrate the typical performance curves. Most of the curves were characterized using signal sources with 50- source impedance, and with measurement equipment presenting a 50- load impedance. In Figure 75, the 49.9- shunt resistor at the VIN terminal matches the source impedance of the test generator. The total 499- load at the output, combined with the 784- total feedback-network load, presents the THS4211 and THS4215 with an effective output load of 305 for the circuit shown in Figure 75. Voltage-feedback amplifiers, unlike current-feedback designs, can use a wide range of resistors values to set their gain with minimal impact on their stability and frequency response. Larger-valued resistors decrease the loading effect of the feedback network on the output of the amplifier, but this enhancement comes at the expense of additional noise and potentially lower bandwidth. Feedback-resistor values between 392 and 1 k are recommended for most applications. 5 V +V S + 100 pF 50 Source 0.1 F 6.8 F + VI VO THS4211 49.9 _ Rf 392 499 392 Rg 0.1 F 6.8 F 100 pF + space space -5 V space -VS Figure 75. Wideband, Noninverting Gain Configuration Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 Submit Documentation Feedback 19 THS4211 THS4215 SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ................................................................................................................................... www.ti.com WIDEBAND, INVERTING GAIN OPERATION Since the THS4211 and THS4215 are general-purpose, wideband voltage-feedback amplifiers, several familiar operational-amplifier applications circuits are available to the designer. Figure 76 shows a typical inverting configuration where the input and output impedances and noise gain from Figure 75 are retained in an inverting circuit configuration. Inverting operation is a common requirement and offers several performance benefits. The inverting configuration shows improved slew rates and distortion due to the pseudo-static voltage maintained on the inverting input. 5 V +V S + 100 pF 0.1 F 6.8 F + RT 200 CT 0.1 F VO THS4211 _ 499 50 Source VI Rg Rf 392 RM 57.6 392 0.1 F 100 pF -5 V 6.8 F + -VS Figure 76. Wideband, Inverting Gain Configuration In the inverting configuration, some key design considerations must be noted. One is that the gain resistor (Rg) becomes part of the signal-channel input impedance. If input impedance matching is desired (beneficial when the signal is coupled through a cable, twisted pair, long PCB trace, or other transmission line conductor), Rg may be set equal to the required termination value and Rf adjusted to give the desired gain. However, care must be taken when 20 Submit Documentation Feedback dealing with low inverting gains, as the resultant feedback resistor value can present a significant load to the amplifier output. For an inverting gain of 2, setting Rg to 49.9 for input matching eliminates the need for RM but requires a 100- feedback resistor. This has the advantage that the noise gain becomes equal to 2 for a 50- source impedance--the same as the noninverting circuit in Figure 75. However, the amplifier output now sees the 100- feedback resistor in parallel with the external load. To eliminate this excessive loading, it is preferable to increase both Rg and Rf, values, as shown in Figure 76, and then achieve the input matching impedance with a third resistor (RM) to ground. The total input impedance becomes the parallel combination of Rg and RM. The next major consideration is that the signal source impedance becomes part of the noise gain equation and hence influences the bandwidth. For example, the RM value combines in parallel with the external 50- source impedance (at high frequencies), yielding an effective source impedance of 50 || 57.6 = 26.8 . This impedance is then added in series with Rg for calculating the noise gain. The result is 1.9 for Figure 76, as opposed to the 1.8 if RM is eliminated. The bandwidth is lower for the inverting gain-of-2 circuit in Figure 76 (NG=+1.9), than for the noninverting gain of 2 circuit in Figure 75. The last major consideration in inverting amplifier design is setting the bias-current cancellation resistor on the noninverting input. If the resistance is set equal to the total dc resistance looking out of the inverting terminal, the output dc error, due to the input bias currents, is reduced to (input offset current) x Rf in Figure 76, the dc source impedance looking out of the inverting terminal is 392 || (392 + 26.8 ) = 200 . To reduce the additional high-frequency noise introduced by the resistor at the noninverting input, and power-supply feedback, RT is bypassed with a capacitor to ground. Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 THS4211 THS4215 www.ti.com ................................................................................................................................... SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 SINGLE-SUPPLY OPERATION The THS4211 is designed to operate from a single 5-V to 15-V power supply. When operating from a single power supply, care must be taken to ensure the input signal and amplifier are biased appropriately to maximize output voltage swing. The circuits shown in Figure 77 demonstrate methods to configure an amplifier for single-supply operation. +VS 50 Source + VI 49.9 RT THS4211 VO _ 499 +VS Rf 2 Rg 392 392 In addition to the power-down pin, the THS4215 also features a reference pin (REF) which allows the user to control the enable or disable power-down voltage levels applied to the PD pin. Operation of the reference pin as it relates to the power-down pin is described below. Rf 392 VS 50 Source VI 57.6 Rg _ 392 THS4211 RT VO + +VS +VS 2 2 The time delays associated with turning the device on and off are specified as the time it takes for the amplifier to reach 50% of the nominal quiescent current. The time delays are on the order of microseconds because the amplifier moves in and out of the linear mode of operation in these transitions. Power-Down Reference Pin Operation +VS 2 Note that this power-down functionality is just that; the amplifier consumes less power in power-down mode. The power-down mode is not intended to provide a high- impedance output. In other words, the power-down functionality is not intended to allow use as a 3-state bus driver. When in power-down mode, the impedance looking back into the output of the amplifier is dominated by the feedback and gain setting resistors, but the output impedance of the device itself varies depending on the voltage applied to the outputs. 499 Figure 77. DC-Coupled Single Supply Operation Saving Power with Power-Down Functionality and Setting Threshold Levels with the Reference Pin The THS4215 features a power-down pin (PD) which lowers the quiescent current from 19-mA down to 650-A, ideal for reducing system power. The power-down pin of the amplifiers defaults to the positive supply voltage in the absence of an applied voltage, putting the amplifier in the power-on mode of operation. To conserve power, the amplifier is turned off by driving the power-down pin towards the negative rail. The threshold voltages for power-on and power-down are relative to the supply rails, and are given in the specification tables. Above the Enable Threshold Voltage, the device is on. Below the Disable Threshold Voltage, the device is off. Behavior between these threshold voltages is not specified. In most split-supply applications, the reference pin will be connected to ground. In some cases, the user may want to connect it to the negative or positive supply rail. In either case, the user needs to be aware of the voltage level thresholds that apply to the power-down pin. The table below illustrates the relationship between the reference voltage and the power-down thresholds. REFERENCE VOLTAGE POWER-DOWN PIN VOLTAGE DEVICE DISABLED DEVICE ENABLED VS- to 0.5 (VS- + VS+) Ref + 1.0 V Ref + 1.8 V 0.5 (VS- + VS+) to VS+ Ref - 1.5 V Ref - 1 V The recommended mode of operation is to tie the reference pin to mid-rail, thus setting the threshold levels to mid-rail +1.0 V and midrail +1.8 V. NO. OF CHANNELS Single (8-pin) Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 PACKAGES THS4215D, THS4215DGN, and THS4215DRB Submit Documentation Feedback 21 THS4211 THS4215 SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ................................................................................................................................... www.ti.com Power-Supply Decoupling Techniques and Recommendations Power-supply decoupling is a critical aspect of any high-performance amplifier design process. Careful decoupling provides higher quality ac performance (most notably, improved distortion performance). The following guidelines ensure the highest level of performance. 1. Place decoupling capacitors as close to the power-supply inputs as possible, with the goal of minimizing the inductance of the path from ground to the power supply. 2. Placement priority should put the smallest valued capacitors closest to the device. 3. Use of solid power and ground planes is recommended to reduce the inductance along power-supply return current paths, with the exception of the areas underneath the input and output pins. 4. Recommended values for power-supply decoupling include a bulk decoupling capacitor (6.8 F to 22 F), a mid-range decoupling capacitor (0.1 F) and a high-frequency decoupling capacitor (1000 pF) for each supply. A 100-pF capacitor can be used across the supplies as well for extremely high-frequency return currents, but often is not required. APPLICATION CIRCUITS Driving an Analog-to-Digital Converter with the THS4211 The THS4211 can be used to drive high-performance analog-to-digital converters. Two example circuits are presented below. The first circuit (in Figure 78) uses a wideband transformer to convert a single-ended input signal into a differential signal. The differential signal is then amplified and filtered by two THS4211 amplifiers. This circuit provides low intermodulation distortion, suppressed even-order distortion, 14 dB of voltage gain, a 50- input impedance, and a single-pole filter at 100 MHz. For applications without signal content at dc, this method of driving ADCs can be very useful. Where dc information content is required, the THS4500 family of fully differential amplifiers may be applicable. 22 Submit Documentation Feedback 5V + VCM THS4211 _ 50 (1:4 ) Source 1:2 196 -5 V 392 24.9 ADS5422 15 pF 14-Bit, 62 Msps 15 pF 196 24.9 392 _ THS4211 + VCM Figure 78. A Linear, Low-Noise, High-Gain ADC Preamplifier The second circuit depicts single-ended ADC drive. While not recommended for optimum performance using converters with differential inputs, satisfactory performance can sometimes be achieved with single-ended input drive. An example circuit is shown in Figure 79 for reference. 50 Source +5 V + VI 49.9 RT RISO 0.1 F THS4211 _ -5 V 16.5 68 pf 12-Bit, 1.82 k Rg ADS807 CM 53 Msps IN Rf 392 IN 0.1 F 392 NOTE: For best performance, high-speed ADCs should be driven differentially. See the THS4500 family of devices for more information. Figure 79. Driving an ADC With a Single-Ended Input Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 THS4211 THS4215 www.ti.com ................................................................................................................................... SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 Using the THS4211 as a DAC Output Buffer Active Filtering with the THS4211 Two example circuits are presented here showing the THS4211 buffering the output of a digital-to-analog converter. The first circuit (Figure 80) performs a differential to single-ended conversion with the THS4211 configured as a difference amplifier. The difference amplifier can double as the termination mechanism for the DAC outputs as well. High-frequency active filtering with the THS4211 is achievable due to the amplifier's high slew-rate, wide bandwidth, and voltage feedback architecture. Several options are available for high-pass, low-pass, bandpass, and bandstop filters of varying orders. A simple two-pole low pass filter is presented in Figure 82 as an example, with two poles at 100 MHz. 3.3 V 3.3 V 100 3.9 pF 392 100 50 Source 392 +5 V 392 DAC5675 14-Bit, 400 MSps _ 196 VI 49.9 392 RF 5V 57.6 THS4211 _ + 49.9 THS4211 392 -5 V 392 VO + LO 33 pF -5 V Figure 80. Differential to Single-Ended Conversion of a High-Speed DAC Output Figure 82. A Two-Pole Active Filter With Two Poles Between 90 MHz and 100 MHz A Low-Noise Receiver with the THS4211 For cases where a differential signaling path is desirable, a pair of THS4211 amplifiers can be used as output buffers. The circuit in Figure 81 depicts a differential drive into a mixer's IF inputs, coupled with additional signal gain and filtering. THS4211 + 3.3 V 3.3 V A combination of two THS4211 amplifiers can create a high-speed, low-distortion, low-noise differential receiver circuit as depicted in Figure 83. With both amplifiers operating in the noninverting mode of operation, the circuit presents a high load impedance to the source. The designer has the option of controlling the impedance through termination resistors if a matched termination impedance is desired. _ 100 100 100 CF 1 nF VI+ 1 nF + 49.9 IF+ DAC5675 14-Bit, 400 MSps 392 100 392 392 49.9 392 49.9 RF(out) 392 787 IF1 nF 1 nF _ VO+ _ 100 392 CF _ + THS4211 VI- Figure 81. Differential Mixer Drive Circuit Using the DAC5675 and the THS4211 100 49.9 VO- + Figure 83. A High Input Impedance, Low-Noise, Differential Receiver space space space Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 Submit Documentation Feedback 23 THS4211 THS4215 SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ................................................................................................................................... www.ti.com A modification on this circuit to include a difference amplifier turns this circuit into a high-speed instrumentation amplifier, as shown in Figure 84. The THS4211 features execllent distortion performance for monolithic operational amplifiers. This section focuses on the fundamentals of distortion, circuit techniques for reducing nonlinearity, and methods for equating distortion of operational amplifiers to desired linearity specifications in RF receiver chains. + Rg2 Rf2 THS4211 _ Rf1 Rg1 _ 100 _ Rf1 THS4211 + 49.9 VO THS4211 Rg2 + 49.9 Rf2 VI+ Figure 84. A High-Speed Instrumentation Amplifier 2R f1 V i)-V i- R f2 VO + 1 1 ) 2 Rg1 Rg2 (1) THEORY AND GUIDELINES Distortion Performance The THS4211 provides excellent distortion performance into a 150- load. Relative to alternative solutions, it provides exceptional performance into lighter loads, as well as exceptional performance on a single 5-V supply. Generally, until the fundamental signal reaches very high frequency or power levels, the 2nd harmonic dominates the total harmonic distortion with a negligible 3rd harmonic component. Focusing then on the 2nd harmonic, increasing the load impedance directly improves distortion. The total load includes the feedback network; in the noninverting configuration (Figure 75) this is the sum of Rf and Rg, while in the inverting configuration (Figure 76), only Rf needs to be included in parallel with the actual load. space Amplifiers are generally thought of as linear devices. The output of an amplifier is a linearly-scaled version of the input signal applied to it. However, amplifier transfer functions are nonlinear. Minimizing amplifier nonlinearity is a primary design goal in many applications. Intercept points are specifications long used as key design criteria in the RF communications world as a metric for the intermodulation distortion performance of a device in the signal chain (e.g., amplifiers, mixers, etc.). Use of the intercept point, rather than strictly the intermodulation distortion, allows simpler system-level calculations. Intercept points, like noise figures, can be easily cascaded back and forth through a signal chain to determine the overall receiver chain's intermodulation distortion performance. The relationship between intermodulation distortion and intercept point is depicted in Figure 85 and Figure 86. PO PO fc = fc - f1 Power 100 VI- LINEARITY: DEFINITIONS, TERMINOLOGY, CIRCUIT TECHNIQUES, AND DESIGN TRADEOFFS fc = f2 - fc IMD3 = PS - PO PS fc - 3f space PS f1 fc f2 fc + 3f f - Frequency - MHz Figure 85. 24 Submit Documentation Feedback Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 THS4211 THS4215 www.ti.com ................................................................................................................................... SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 OIP 3 + P O ) POUT (dBm) 1X P O + 10 log OIP3 IMD2 where 3 2RL (2) V 2P 0.001 (3) NOTE: PO is the output power of a single tone, RL is the load resistance, and VP is the peak voltage for a single tone. PO NOISE ANALYSIS PIN (dBm) IIP3 IMD3 3X PS Figure 86. Due to the intercept point's ease of use in system level calculations for receiver chains, it has become the specification of choice for guiding distortion-related design decisions. Traditionally, these systems use primarily class-A, single-ended RF amplifiers as gain blocks. These RF amplifiers are typically designed to operate in a 50- environment. Giving intercept points in dBm implies an associated impedance (50 ). However, with an operational amplifier, the output does not require termination as an RF amplifier would. Because closed-loop amplifiers deliver signals to their outputs regardless of the impedance present, it is important to comprehend this when evaluating the intercept point of an operational amplifier. The THS4211 yields optimum distortion performance when loaded with 150 to 1 k, very similar to the input impedance of an analog-to-digital converter over its input frequency band. As a result, terminating the input of the ADC to 50 can actually be detrimental to system performance. The discontinuity between open-loop, class-A amplifiers and closed-loop, class-AB amplifiers becomes apparent when comparing the intercept points of the two types of devices. Equation 2 and Equation 3 define an intercept point, relative to the intermodulation distortion. High slew rate, unity-gain stable, voltage-feedback operational amplifiers usually achieve their slew rate at the expense of a higher input noise voltage. The 7-nV/Hz input voltage noise for the THS4211 and THS4215 is, however, much lower than comparable amplifiers. The input-referred voltage noise and the two input-referred current noise terms (4 pA/Hz) combine to give low output noise under a wide variety of operating conditions. Figure 87 shows the amplifier noise analysis model with all the noise terms included. In this model, all noise terms are taken to be noise voltage or current density terms in either nV/Hz or pA/Hz. THS4211/THS4215 ENI + RS ERS IBN EO _ 4kTRS Rf Rg 4kT Rg IBI ERF 4kTRf 4kT = 1.6E-20J at 290K Figure 87. Noise Analysis Model The total output shot noise voltage can be computed as the square of all square output noise voltage contributors. Equation 4 shows the general form for the output noise voltage using the terms shown in Equation 4: EO + 2 2 ENI 2 ) IBNRS ) 4kTR S NG 2 ) IBIRf ) 4kTRfNG Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 (4) Submit Documentation Feedback 25 THS4211 THS4215 SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ................................................................................................................................... www.ti.com Dividing this expression by the noise gain [NG= (1 + Rf/Rg) ] gives the equivalent input-referred spot noise voltage at the noninverting input, as shown in Equation 5: 1 2 2 E NI 2 ) I BNRS ) 4kTR S ) INGR ) 4kTR NG BI f 0.5 VS =5 V R(ISO) = 10 CL = 100 pF f (5) Driving Capacitive Loads One of the most demanding, and yet very common, load conditions for an op amp is capacitive loading. Often, the capacitive load is the input of an A/D converter, including additional external capacitance, which may be recommended to improve A/D linearity. A high-speed, high open-loop gain amplifier like the THS4211 can be very susceptible to decreased stability and closed-loop response peaking when a capacitive load is placed directly on the output pin. When the amplifier's open-loop output resistance is considered, this capacitive load introduces an additional pole in the signal path that can decrease the phase margin. When the primary considerations are frequency response flatness, pulse response fidelity, or distortion, the simplest and most effective solution is to isolate the capacitive load from the feedback loop by inserting a series isolation resistor between the amplifier output and the capacitive load. This does not eliminate the pole from the loop response, but rather shifts it and adds a zero at a higher frequency. The additional zero acts to cancel the phase lag from the capacitive load pole, thus increasing the phase margin and improving stability. The Typical Characteristics show the recommended isolation resistor vs capacitive load and the resulting frequency response at the load. Parasitic capacitive loads greater than 2 pF can begin to degrade the performance of the THS4211. Long PCB traces, unmatched cables, and connections to multiple devices can easily cause this value to be exceeded. Always consider this effect carefully, and add the recommended series resistor as close as possible to the THS4211 output pin (see Board Layout Guidelines). The criterion for setting this R(ISO) resistor is a maximum bandwidth, flat frequency response at the load. For a gain of +2, the frequency response at the output pin is already slightly peaked without the capacitive load, requiring relatively high values of R(ISO) to flatten the response at the load. Increasing the noise gain also reduces the peaking. Normalized Gain - dB EO + FREQUENCY RESPONSE vs CAPACITIVE LOAD 0 -0.5 R(ISO) = 15 CL = 50 pF -1 -1.5 R(ISO) = 25 CL = 10 pF -2 -2.5 -3 100 k 1M 10 M 100 M 1G Capacitive Load - Hz Figure 88. Isolation Resistor Diagram BOARD LAYOUT Achieving optimum performance with a high frequency amplifier like the THS4211 requires careful attention to board layout parasitics and external component types. Recommendations that optimize performance include the following: 1. Minimize parasitic capacitance to any ac ground for all of the signal I/O pins. Parasitic capacitance on the output and inverting input pins can cause instability: on the noninverting input, it can react with the source impedance to cause unintentional band limiting. To reduce unwanted capacitance, a window around the signal I/O pins should be opened in all of the ground and power planes around those pins. Otherwise, ground and power planes should be unbroken elsewhere on the board. 2. Minimize the distance (< 0.25") from the power supply pins to high frequency 0.1-F decoupling capacitors. At the device pins, the ground and power plane layout should not be in close proximity to the signal I/O pins. Avoid narrow power and ground traces to minimize inductance between the pins and the decoupling capacitors. The power supply connections should always be decoupled with these capacitors. Larger (2.2-F to 6.8-F) decoupling capacitors, effective at lower frequency, should also be used on the main supply pins. These may be placed somewhat farther from the device and may be shared among several devices in the same area of the PCB. space space 26 Submit Documentation Feedback Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 THS4211 THS4215 www.ti.com ................................................................................................................................... SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 3. Careful selection and placement of external components preserves the high frequency performance of the THS4211. Resistors should be a very low reactance type. Surface-mount resistors work best and allow a tighter overall layout. Metal-film and carbon composition, axially-leaded resistors can also provide good high frequency performance. Again, keep their leads and PCB trace length as short as possible. Never use wire-wound type resistors in a high-frequency application. Since the output pin and inverting input pin are the most sensitive to parasitic capacitance, always position the feedback and series output resistor, if any, as close as possible to the output pin. Other network components, such as noninverting input-termination resistors, should also be placed close to the package. Where double-side component mounting is allowed, place the feedback resistor directly under the package on the other side of the board between the output and inverting input pins. Even with a low parasitic capacitance shunting the external resistors, excessively high resistor values can create significant time constants that can degrade performance. Good axial metal-film or surface-mount resistors have approximately 0.2 pF in shunt with the resistor. For resistor values > 2.0 k, this parasitic capacitance can add a pole and/or a zero below 400 MHz that can effect circuit operation. Keep resistor values as low as possible, consistent with load driving considerations. A good starting point for design is to set the Rf to 249 for low-gain, noninverting applications. This setting automatically keeps the resistor noise terms low and minimizes the effect of their parasitic capacitance. 4. Connections to other wideband devices on the board may be made with short direct traces or through onboard transmission lines. For short connections, consider the trace and the input to the next device as a lumped capacitive load. Relatively wide traces (50 mils to 100 mils) should be used, preferably with ground and power planes opened up around them. Estimate the total capacitive load and set RISO from the plot of recommended RISO vs capacitive load (See Figure 88). Low parasitic capacitive loads (< 4 pF) may not need an R(ISO), since the THS4211 is nominally compensated to operate with a 2-pF parasitic load. Higher parasitic capacitive loads without an R(ISO) are allowed as the signal gain increases (increasing the unloaded phase margin). If a long trace is required, and the 6-dB signal loss intrinsic to a doubly-terminated transmission line is acceptable, implement a matched impedance transmission line using microstrip or stripline techniques (consult an ECL design handbook for microstrip and stripline layout techniques). A 50- environment is normally not necessary onboard, and in fact a higher impedance environment improves distortion as shown in the distortion versus load plots. With a characteristic board trace impedance defined on the basis of board material and trace dimensions, a matching series resistor into the trace from the output of the THS4211 is used as well as a terminating shunt resistor at the input of the destination device. Remember also that the terminating impedance is the parallel combination of the shunt resistor and the input impedance of the destination device: this total effective impedance should be set to match the trace impedance. If the 6-dB attenuation of a doubly-terminated transmission line is unacceptable, a long trace can be series-terminated at the source end only. Treat the trace as a capacitive load in this case and set the series resistor value as shown in the plot of R(ISO) vs capacitive load (See Figure 88). This setting does not preserve signal integrity or a doubly-terminated line. If the input impedance of the destination device is low, there is some signal attenuation due to the voltage divider formed by the series output into the terminating impedance. 5. Socketing a high speed part like the THS4211 is not recommended. The additional lead length and pin-to-pin capacitance introduced by the socket can create a troublesome parasitic network which can make it almost impossible to achieve a smooth, stable frequency response. Best results are obtained by soldering the THS4211 onto the board. PowerPADTM DESIGN CONSIDERATIONS The THS4211 and THS4215 are available in a thermally-enhanced PowerPAD family of packages. These packages are constructed using a downset leadframe upon which the die is mounted [see Figure 89(a) and Figure 89(b)]. This arrangement results in the lead frame being exposed as a thermal pad on the underside of the package [see Figure 89(c)]. Because this thermal pad has direct thermal contact with the die, excellent thermal performance can be achieved by providing a good thermal path away from the thermal pad. The PowerPAD package allows both assembly and thermal management in one manufacturing operation. During the surface-mount solder operation (when the leads are being soldered), the thermal pad can also be soldered to a copper area underneath the package. Through the use of thermal paths within this copper area, heat can be conducted away from the package into either a ground plane or other heat dissipating device. Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 Submit Documentation Feedback 27 THS4211 THS4215 SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ................................................................................................................................... www.ti.com The PowerPAD package represents a breakthrough in combining the small area and ease of assembly of surface mount with the heretofore awkward mechanical methods of heatsinking. DIE Thermal Pad Side View (a) DIE End View (b) Bottom View (c) Figure 89. Views of Thermally Enhanced Package Although there are many ways to properly heatsink the PowerPAD package, the following steps illustrate the recommended approach. PowerPAD PCB LAYOUT CONSIDERATIONS 1. Prepare the PCB with a top side etch pattern as shown in Figure 90. There should be etching for the leads as well as etch for the thermal pad. III IIIIII III III III III IIIIII III III III III IIIIII Single or Dual 68 Mils x 70 Mils (Via Diameter = 13 Mils) Figure 90. PowerPAD PCB Etch and Via Pattern 2. Place five holes in the area of the thermal pad. These holes should be 13 mils in diameter. Keep them small so that solder wicking through the holes is not a problem during reflow. 3. Additional vias may be placed anywhere along the thermal plane outside of the thermal pad area. They help dissipate the heat generated by the THS4211 and THS4215 IC. These additional vias may be larger than the 13-mil diameter vias directly under the thermal pad. They can be larger because they are not in the thermal pad area to be soldered, so wicking is not a problem. 4. Connect all holes to the internal ground plane. 5. When connecting these holes to the ground plane, do not use the typical web or spoke via connection methodology. Web connections have a high thermal resistance connection that is useful for slowing the heat transfer during soldering operations. This resistance makes the soldering of vias that have plane connections easier. In this application, however, low thermal resistance is desired for the most efficient heat 28 Submit Documentation Feedback transfer. Therefore, the holes under the THS4211 and THS4215 PowerPAD package should make their connection to the internal ground plane, with a complete connection around the entire circumference of the plated-through hole. 6. The top-side solder mask should leave the terminals of the package and the thermal pad area with its five holes exposed. The bottom-side solder mask should cover the five holes of the thermal pad area. This prevents solder from being pulled away from the thermal pad area during the reflow process. 7. Apply solder paste to the exposed thermal pad area and all of the IC terminals. 8. With these preparatory steps in place, the IC is simply placed in position and run through the solder reflow operation as any standard surface-mount component. This results in a part that is properly installed. For a given JA, the maximum power dissipation is shown in Figure 91 and is calculated by Equation 6: Tmax * T A PD + q JA where PD = Maximum power dissipation of THS4211 (watts) TMAX = Absolute maximum junction temperature (150C) TA = Free-ambient temperature (C) JA = JC + CA JC = Thermal coefficient from junction to the case CA = Thermal coefficient from the case to ambient air (C/W). (6) The next consideration is the package constraints. The two sources of heat within an amplifier are quiescent power and output power. The designer should never forget about the quiescent heat generated within the device, especially multi-amplifier devices. Because these devices have linear output stages (Class AB), most of the heat dissipation is at low output voltages with high output currents. The other key factor when dealing with power dissipation is how the devices are mounted on the PCB. The PowerPAD devices are extremely useful for heat dissipation. But, the device should always be soldered to a copper plane to fully use the heat dissipation properties of the PowerPAD. The SOIC package, on the other hand, is highly dependent on how it is mounted on the PCB. As more trace and copper area is placed around the device, JA decreases and the heat dissipation capability increases. For a single package, the sum of the RMS output currents and voltages should be used to choose the proper package. Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 THS4211 THS4215 www.ti.com ................................................................................................................................... SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 The THS4211 device does not incorporate automatic thermal shutoff protection, so the designer must take care to ensure that the design does not violate the absolute maximum junction temperature of the device. Failure may result if the absolute maximum junction temperature of 150C is exceeded. The thermal characteristics of the device are dictated by the package and the PCB. Maximum power dissipation for a given package can be calculated using Equation 7: Tmax-T A P Dmax + q JA where PDmax is the maximum power dissipation in the amplifier (W). Tmax is the absolute maximum junction temperature (C). TA is the ambient temperature (C). JA = JC + CA JC is the thermal coefficient from the silicon junctions to the case (C/W). CA is the thermal coefficient from the case to ambient air (C/W). (7) For systems where heat dissipation is more critical, the THS4211 is offered in an 8-pin MSOP with PowerPAD. The thermal coefficient for the MSOP PowerPAD package is substantially improved over the traditional SOIC. Maximum power dissipation levels are depicted in the graph for the two packages. The data for the DGN package assumes a board layout that follows the PowerPAD layout guidelines referenced above and detailed in the PowerPAD application notes in the Additional Reference Material section at the end of the data sheet. PD - Maximum Power Dissipation - W 3.5 8-Pin DGN Package 3 2.5 2 When determining whether or not the device satisfies the maximum power dissipation requirement, it is important to consider not only quiescent power dissipation, but also dynamic power dissipation. Often maximum power dissipation is difficult to quantify because the signal pattern is inconsistent, but an estimate of the RMS power dissipation can provide visibility into a possible problem. DESIGN TOOLS Performance vs Package Options The THS4211 and THS4215 are offered in a different package options. However, performance may be limited due to package parasitics and lead inductance in some packages. In order to achieve maximum performance of the THS4211 and THS4215, Texas Instruments recommends using the leadless MSOP (DRB) or MSOP (DGN) packages, in addition to proper high-speed PCB layout. Figure 92 shows the unity-gain frequency response of the THS4211 using the leadless MSOP, MSOP, and SOIC package for comparison. Using the THS4211 and THS4215 in a unity-gain with the SOIC package may result in the device becoming unstable. In higher gain configurations, this effect is mitigated by the reduced bandwidth. As such, the SOIC is suitable for application with gains equal to or higher than +2 V/V or (-1 V/V). 12 _ 10 499 49.9 6 4 SOIC, Rf = 100 2 0 -2 8-Pin D Package PIN = -7 dB VS =5 V -4 1.5 SOIC, Rf = 0 Rf + 8 Normalized Gain - dB THERMAL ANALYSIS 10 M Leadless MSOP, & MSOP Rf = 0 100 M 1G f - Frequency - Hz 1 Figure 92. Effects of Unity-Gain Frequency Response for Differential Packages 0.5 0 -40 -20 0 20 40 60 TA - Ambient Temperature - C 80 JA = 170C/W for 8-Pin SOIC (D) JA = 58.4C/W for 8-Pin MSOP (DGN) TJ= 150C, No Airflow Figure 91. Maximum Power Dissipation vs Ambient Temperature Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 Submit Documentation Feedback 29 THS4211 THS4215 SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ................................................................................................................................... www.ti.com Evaluation Fixtures, SPICE Models, and Applications Support Texas Instruments is committed to providing its customers with the highest quality of applications support. To support this goal, evaluation boards have been developed for the THS4211 operational amplifier. Three evaluation boards are available: one THS4211 and one THS4215, both configurable for different gains, and a third for untiy gain (THS4211 only). These boards are easy to use, allowing for straightforward evaluation of the device. These evaluation boards can be ordered through the Texas Instruments web site at www.ti.com, or through your local Texas Instruments sales representative. Schematics for the evaluation boards are shown below. The THS4211/THS4215 EVM board shown in Figure 95 through Figure 99 accommodates different gain configurations. Its default component values are set to give a gain of 2. The EVM can be configured for unity-gain; however, it is strongly not recommended. Evaluating the THS4211/THS4215 in unity-gain using this EVM may cause the device to become unstable. The stability of the device can be controlled by adding a large resistor in the feedback path, but performance is sacrificed. Figure 93 shows the small-signal frequency response of the THS4211 with different feedback resistors in the feedback path. Figure 94 is the small frequency response of the THS4211 using the unity-gain EVM. Small Signal Gain - dB 17 15 _ 13 + Rf Rf = 50 9 7 Rf = 200 3 1 -1 -3 -5 PIN = -7 dBm VS = 5 V 10 M 100 M 1G 10 G f - Frequency - Hz Figure 93. Frequency Response vs Feedback Resistor Using the EDGE #6439527 EVM 30 _ 3 + 499 49.9 2 1 0 -1 -2 PIN = -7 dBm VS = 5 V -3 -4 100 k Submit Documentation Feedback 1M 10 M 100 M f - Frequency - Hz 1G 10 G Figure 94. Frequency Response Using the EDGE #6443547 G = +1 EVM The frequency-response peaking is due to the lead inductance in the feedback path. Each pad and trace on a PCB has an inductance associated with it, which in conjunction with the inductance associated with the package may cause frequency-response peaking, causing the device to become unstable. In order to achieve the maximum performance of the device, PCB layout is very critical. Texas Instruments has developed an EVM for the evaluation of the THS4211 configured for a gain of 1. The EVM is shown in Figure 100 through Figure 104. This EVM is designed to minimize peaking in the unity-gain configuration. Rf = 100 5 4 Minimizing the inductance in the feedback path is critical for reducing the peaking of the frequency response in unity-gain. The recommended maximum inductance allowed in the feedback path is 4 nH. This inductance can be calculated using Equation 8: L(nH) + K ln 2 ) 0.223 W ) T ) 0.5 W)T Rf = 0 499 49.9 11 Small Signal Gain - dB 5 where W = Width of trace in inches. = Length of the trace in inches. T = Thickness of the trace in inches. K = 5.08 for dimensions in inches, and K = 2 for dimensions in cm. (8) space Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 THS4211 THS4215 www.ti.com ................................................................................................................................... SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 Vs+ J9 Power Down R8 C8 R9 R5 Vs - Vs+ 7 8 2 _ R3 J1 Vin - U1 R6 6 J4 Vout 3 + R2 R7 4 1 Vs - J2 Vin+ J8 Power Down Ref C7 R1 R4 J7 VS- J6 GND J5 VS+ TP1 FB1 FB2 VS- C5 C6 Figure 96. THS4211/THS4215 EVM Board Layout (Top Layer) VS+ C1 C2 + C3 + C4 Figure 95. THS4211/THS4215 EVM Circuit Configuration Figure 97. THS4211/THS4215 EVM Board Layout (Second Layer, Ground) Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 Submit Documentation Feedback 31 THS4211 THS4215 SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ................................................................................................................................... www.ti.com Vs+ 7 8 2 _ U1 R6 6 J4 Vout 3 + R7 4 1 J2 Vin+ Vs R4 J7 VS- J6 GND J5 VS+ TP1 FB1 FB2 VS- C5 VS+ C1 C6 + C2 + C3 C4 Figure 100. THS4211 Unity-Gain EVM Circuit Configuration Figure 98. THS4211/THS4215 EVM Board Layout (Third Layer, Power) Figure 101. THS4211 Unity-Gain EVM Board Layout (Top Layer) Figure 99. THS4211/THS4215 EVM Board Layout (Bottom Layer) 32 Submit Documentation Feedback Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 THS4211 THS4215 www.ti.com ................................................................................................................................... SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 Figure 102. THS4211 Unity-Gain EVM Board Layout (Second Layer, Ground) Figure 103. THS4211 Unity-Gain EVM Board Layout (Third Layer, Power) Figure 104. THS4211 Unity-Gain EVM Board Layout (Bottom Layer) Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 Submit Documentation Feedback 33 THS4211 THS4215 SLOS400E - SEPTEMBER 2002 - REVISED SEPTEMBER 2009 ................................................................................................................................... www.ti.com Computer simulation of circuit performance using SPICE is often useful when analyzing the performance of analog circuits and systems. This is particularly true for video and RF amplifier circuits, where parasitic capacitance and inductance can have a major effect on circuit performance. A SPICE model for the THS4500 family of devices is available through the Texas Instruments web site (www.ti.com). The Product Information Center (PIC) is available for design assistance and detailed product information. These models do a good job of predicting small-signal ac and transient performance under a wide variety of operating conditions. They are not intended to model the distortion characteristics of the amplifier, nor do they attempt to distinguish between the package types in their small-signal ac performance. Detailed information about what is and is not modeled is contained in the model file itself. ADDITIONAL REFERENCE MATERIAL * * PowerPAD Made Easy, application brief (SLMA004) PowerPAD Thermally-Enhanced Package, technical brief (SLMA002) space REVISION HISTORY NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision D (November, 2004) to Revision E .......................................................................................... Page * Updated document format to current standards ................................................................................................................... 1 * Changed high output drive (IO) bullet in Features list from 200 mA to 170 mA ................................................................... 1 * Changed Absolute Maximum Ratings table; increased output current specification, deleted lead temperature specification .......................................................................................................................................................................... 2 * Corrected typo in Turn-off-time delay parametric units; changed to s ............................................................................... 7 34 Submit Documentation Feedback Copyright (c) 2002-2009, Texas Instruments Incorporated Product Folder Link(s): THS4211 THS4215 PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) THS4211D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM THS4211DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM THS4211DGK ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM THS4211DGKG4 ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM THS4211DGN ACTIVE MSOPPowerPAD DGN 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM THS4211DGNG4 ACTIVE MSOPPowerPAD DGN 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM THS4211DGNR ACTIVE MSOPPowerPAD DGN 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM THS4211DGNRG4 ACTIVE MSOPPowerPAD DGN 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM THS4211DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM THS4211DRBR ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR THS4211DRBRG4 ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR THS4211DRBT ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR THS4211DRBTG4 ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR THS4211DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM THS4215D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM THS4215DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM THS4215DGK ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 1 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 16-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) THS4215DGKG4 ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM THS4215DGN ACTIVE MSOPPowerPAD DGN 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM THS4215DGNG4 ACTIVE MSOPPowerPAD DGN 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM THS4215DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM THS4215DRBR ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR THS4215DRBRG4 ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR THS4215DRBT ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR THS4215DRBTG4 ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR THS4215DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing THS4211DGNR MSOPPower PAD THS4211DR THS4211DRBR SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant DGN 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 SON DRB 8 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 THS4211DRBT SON DRB 8 250 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 THS4215DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 THS4215DRBR SON DRB 8 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 THS4215DRBT SON DRB 8 250 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) THS4211DGNR MSOP-PowerPAD DGN 8 2500 358.0 335.0 35.0 THS4211DR SOIC D 8 2500 367.0 367.0 35.0 THS4211DRBR SON DRB 8 3000 338.1 338.1 20.6 THS4211DRBT SON DRB 8 250 338.1 338.1 20.6 THS4215DR SOIC D 8 2500 367.0 367.0 35.0 THS4215DRBR SON DRB 8 3000 338.1 338.1 20.6 THS4215DRBT SON DRB 8 250 338.1 338.1 20.6 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated