2014.11w
Circular Connectors Supporting TÜV and MIL spec.
H/MS Series
Features
1. Compatible with MIL spec. standard
products
2. A ground circuit is provided in the
TÜV approved connectors
3. Waterproof
The mated plug/receptacle combinations and
un-mated receptacles are compliant to IP67F and
IP68F ratings.
IP67: Left in water at a depth of 1 m for 30 minutes
IP68: Left in water at a depth of 2 m for 14 days
Product Specifi cations
Standard products
Ratings
Shell size 10SL 18 20 22 24
Contact arrangement 4 3 10 15 29 14 22 23 10
Number of contacts 23471719487
Rated current (A)/contact
The fi gure in [ ] indicates the total
capacity of the connector.
13
[24.5]
13
[34.5]
23
[76.2]
23
[105.7]
13
[44.2]
13A
[49.4]
46
[152.5]
23
[100.4]
46
[211.5]
Rated voltage AC500V, DC700V
Operation temperature range -40 to +125℃
Storage temperature range -10 to +60℃
TÜV approved products
Ratings
Shell size 10SL 18 22 24
Contact arrangement 3 10 22 10
Number of contacts 3 4 4 7
Rated current (A)/contact 7 10 13 17 23 17 23 23 35 46 23 35 46 23 35
Wire size (mm2) 0.5 0.75 1.25 2 3.5 2 3.5 3.5 5.5 8 3.5 5.5 8 3.5 5.5
Rated voltage (V) 200 500 250 500 250 250
Degree of pollution 3 2 3 2 3 2
Conducting voltage category ⅢⅡⅢⅡ ⅢⅡ
Operation temperature range -40 to +125℃
Storage temperature range -10 to +60℃
Performance
Items Specifi cations Conditions
1. Contact resistance
10SL, 20-29, 22-14: 5 mø max.
18-10, 20-15, 22-23: 3 mø max.
22-22, 24-10: 1 mø max.
Measured at DC 1 A
2. Insulation resistance 5,000 Mø min. Measured at DC 500 V
3. Withstanding voltage No fl ashover or dielectric breakdown AC 2,250 V for one minute
4. Vibration Resistance No electrical discontinuity for 10 µs min.
10 to 500 Hz/cycle, full amplitude: 0.75 mm, with
98 m/s2, 3 directions, 3 hours each
10 to 500 Hz/cycle, full amplitude: 0.75 mm, with
98 m/s2, 3 axis directions, 3 hours each
5. Shock resistance No electrical discontinuity for 10 µs min. Acceleration: 490 m/s2, duration: 11 ms,
3 axis directions, 3 cycles each
6. Mating Cycles Contact resistance : Initial value x for 1.5 mø max. 500 times
7. Temperature cycle Insulation resistance: a minimum of 500 Mø
-55ç: 30 minutes ➝ Normal temperature: 10
to 15 minutes ➝ 125ç: 30 minutes ➝ Normal
temperature: 10 to 15 minutes, left for 5 cycles
8. Moisture resistance
Insulation resistance:
a minimum of 50 Mø (at high humidity min.
500 Mø (when dry) min.
Temperature: 71ç, relative humidity: 95%, left for
336 hours
9. Waterproof No water penetration into the connector. Left in water at a depth of 1 m for 0.5 hours in the
mated state.
1
Materials
Material Finish Remarks
Shell Aluminum alloy
(Zinc alloy: H/MS3108B plug cord tube)
Black chromate
treatment ----------------------
Insulator PPS resin, PBT resin, or silicone rubber Black
UL94V-0
(Excluding silicone
rubber)
Contact Copper alloy Silver plating ----------------------
Bushing Acrylonitrile-butadiene rubber
(Chloroprene rubber: H/MS08A plug) Black ----------------------
Ordering information
●Plug and receptacle
H/MSA 3102 A 18 - 10 P X - D - T (01)
❶ ❷❸❹ ❺❻❼❽❾⓫
●Clamp
H/MSA 3057 - 4A (01)
❶❷ ❿⓫
qModel name: H/MS Series.
wShape : Indicates the shape of the connector.
3102 : Receptacle
3106 : Straight plug
3108 : Right angle shaped plug 08: Low-profi le, right angle shaped plug
3057 : Cord clamp
eStructure: Indicates the structure of the connector.
A: Integrated shell
B: Separated shell
r Shell size: This is the diameter of the screw (inches) at the termination end multiplied by the constant of 16. (Example: The
shell size of 18 is calculated by 1 1/8” x 16 = 18.)
tContact arrangement: See pages 10 and 11 for details on contact arrangement.
yContact form: Indicates the termination style.
P : Soldered, male contact
S : Soldered, female contact
PC : Crimped, male contact
SC : Crimped, female contact
u
Variations of insert position: The letters W, X, Y, or Z are used for any changes in the insert position from that of the
standard type.
i Ground contact number: Notes the grounded contact for TÜV approved products. The ground contact position corresponds
to contacts C, D, or G, and varies depending on shell size. Part numbers without this symbol
indicate that the part does not include a ground contact.
oTÜV approved product: TÜV approved products that are compliant with DIN VDE 0627.
!0Clamp size: Indicates both clamp size and structure.
!1Other specifi cations: A two-digit number such as (01) or (02) is added to indicate other specifi cations.
2
H/MS Series●Circular Connectors Supporting TÜV and MIL spec.
Spanner/wrench flat width (mm) E
D
Ｘ
Ｄ
Ｃ
Ｂ
Ａ
Ｙ
１８−１０Ｓ
C
B
ØA
Straight plug
Standard products
HRS No. Part No. No. of contacts ØAB C D E
120-0601-3 73 H/MS3106A10SL-4S(73) 2 22 36.8
10
5/8-24UNEF-2A ----
120-0603-9 73 H/MS3106A10SL-3S(73) 3
120-0605-4 73 H/MS3106A18-10S(73) 4 33.5 50 1-20UNEF-2A 27
120-0611-7 73 H/MS3106A20-29S(73) 17 37
54.5 1 3/16-18UNEF-2A 32
120-0611-7 77 H/MS3106A20-29SW(77)
120-0613-2 73 H/MS3106A22-14S(73) 19 39.5
120-0615-8 73 H/MS3106A22-22S(73) 4
120-0619-9 73 H/MS3106A24-10S(73) 7 43 57.7 1 7/16-18UNEF-2A 37
TÜV approved products
HRS No. Part No. No. of contacts ØA B C D E
120-0326-0 73 H/MS3106A10SL-3S-C-T(73) 3 22 36.8
10
5/8-24UNEF-2A ----
120-0323-2 73 H/MS3106A18-10S-D-T(73) 433.5 50 1-20UNEF-2A 27
120-0324-5 73 H/MS3106A22-22S-D-T(73) 39.5 54.5 1 3/16-18UNEF-2A 32
120-0325-8 73 H/MS3106A24-10S-G-T(73) 7 43 57.7 1 7/16-18UNEF-2A 37
(Representative example)
H/MS3106A18-10S-D-T(73)
ØA
B
D
C
１８
Spanner/wrench flat width (mm) F
E
Right-angled plug
Standard products
HRS No. Part No. No. of contacts ØA B C D E F
120-0701-8 73 H/MS3108B10SL-4S(73) 2 22 37.3 24.5
11.6
5/8-24UNEF-2A 20
120-0703-3 73 H/MS3108B10SL-3S(73) 3
120-0705-9 73 H/MS3108B18-10S(73) 4 33.5 54.5 32 1-20UNEF-2A 32
120-0709-0 73 H/MS3108B20-15S(73) 7
37
60.7 34 1 3/16-18UNEF-2A
35120-0711-1 73 H/MS3108B20-29S(73) 17
120-0711-1 74 H/MS3108B20-29SW(74)
120-0713-7 73 H/MS3108B22-14S(73) 19 39.5 38
120-0715-2 73 H/MS3108B22-22S(73) 4
120-0719-3 73 H/MS3108B24-10S(73) 7 43 67.1 39.6 1 7/16-18UNEF-2A 41
TÜV approved products
HRS No. Part No. No. of contacts ØA B C D E F
120-0421-1 73 H/MS3108B10SL-3S-C-T(73) 3 22 37.3 24.5
11.6
5/8-24UNEF-2A 20
120-0422-4 73 H/MS3108B18-10S-D-T(73) 433.5 54.5 32 1-20UNEF-2A 32
120-0423-7 73 H/MS3108B22-22S-D-T(73) 39.5 60.7 34 1 3/16-18UNEF-2A 38
120-0424-0 73 H/MS3108B24-10S-G-T(73) 7 43 67.1 39.6 1 7/16-18UNEF-2A 41
(Note) With some models it may be diffi cult to push the cable through the connector, even when the cable is within the applicable range.
Waterproof performance and cable clamp capability may differ depending on the cable specifi cation. Please make sure
all specifi cations are met before actual use.
(Representative example)
H/MS3108B18-10S-D-T(73)
3
H/MS Series●Circular Connectors Supporting TÜV and MIL spec.
１８
３０５７−１０
Ｙ
Ｄ
Ｘ
１８−１０Ｓ Ｃ
Ｂ
Ａ
18 size: Ø33.5
(22 size: Ø39.5)
(22 size: 67.5)
18 size: 45.5
18 size: 31
18 size: 41
(22 size: 45.8)
(22 size: 36)
１８
Ｙ
Ｄ
Ｘ
１８−１０Ｓ Ｃ
Ｂ
Ａ
Ø33.5
35.5
41
Ø30
Low-profi le, right-angled plug (with cord clamp)
TÜV approved products
HRS No. Part No. No. of
contacts Weight Applicable cable
diameter Solder pot diameter
120-0476-3 73 H/MS08A18-10S-DT10D(73) 4 89g Ø12 〜14.3mm Ø2.5
120-0481-3 73 H/MS08A18-10S-DT10D1(73) Ø10 〜12.5mm
120-0477-6 73 H/MS08A22-22S-DT12D(73)
4 127g Ø13 〜15.9mm Ø4.5120-0477-6 74 H/MS08A22-22S-DT12D(74)
120-0482-6 74 H/MS08A22-22S-DT12D1(74) Ø10 〜13.5mm
TÜV approved products
HRS No. Part No. No. of
contacts Weight Applicable cable
diameter Solder pot diameter
120-0480-074 H/MS08A18-10S-DT10C(74) 4 77.6g Ø13 〜14.3mm Ø2.5
1.Partnumbersuffix
(73) Specification: products with a wire hole in the locking ring to prevent loosening of the ring.
(74) Specification: products without a wire hole in the locking ring.
(Representative example)
(Representative example)
H/MS08A18-10S-DT10D(73)
H/MS08A18-10S-DT10C(74)
4
H/MS Series●Circular Connectors Supporting TÜV and MIL spec.
ØA
B
C
D
Ｄ
Ｃ
Ｂ
Ａ
Ｙ
Ｘ
１８−１０Ｓ
Single block (waterproof)
Standard products
HRS No. Part No. No. of contacts ØA B C D
120-0601-3 76 H/MS3106A10SL-4S(76) 2 22 24 6.5 9/16-24UNEF-2A
120-0603-9 76 H/MS3106A10SL-3S(76) 3
120-0605-4 76 H/MS3106A18-10S(76) 4 33.5 31.2 8 1-20UNEF-2A
120-0611-7 76 H/MS3106A20-29S(76) 17 37
33.2 10
1 1/8-18UNEF-2A
120-0611-7 78 H/MS3106A20-29SW(78)
120-0613-2 76 H/MS3106A22-14S(76) 19 39.5 1 1/4-18UNEF-2A
120-0615-8 76 H/MS3106A22-22S(76) 4
120-0619-9 76 H/MS3106A24-10S(76) 7 43 34.7 1 3/8-18UNEF-2A
TÜV approved products
HRS No. Part No. No. of contacts ØA B C D
120-0326-0 76 H/MS3106A10SL-3S-C-T(76) 3 22 24 6.5 9/16-24UNEF-2A
120-0323-2 76 H/MS3106A18-10S-D-T(76) 433.5 31.2 8 1-20UNEF-2A
120-0324-5 76 H/MS3106A22-22S-D-T(76) 39.5 33.2 10 1 1/4-18UNEF-2A
120-0325-8 76 H/MS3106A24-10S-G-T(76) 7 43 34.7 1 3/8-18UNEF-2A
This connector is designed for use with flexible conduit or cabtire
cable connectors.(See page 8 for the table of compatibilities for
H/MS connectors and other connectors.)
(Representative example)
H/MS3106A-18-10S-D-T(76)
Receptacle (solder type)
Standard products
HRS No. Part No. No. of contacts A B ØC D E F G ØH I
120-0111-4 73 H/MS3102A10SL-4P(73) 2 18.26 25.4
3.3
14.5 2.2 23.6 28.3 15.6
5/8-24UNEF-2A
120-0113-0 73 H/MS3102A10SL-3P(73) 3
120-0101-0 73 H/MS3102A18-10P(73) 4 26.97 34.92
19.3 2.8
30 35 26.6
1 1/8-18UNEF-2A
120-0115-5 73 H/MS3102A20-15P(73) 7
29.36 38.1 29.4 29.6
1 1/4-18UNEF-2A
120-0103-6 73 H/MS3102A20-29P(73) 17 33
120-0103-6 74 H/MS3102A20-29PW(74)
120-0107-7 73 H/MS3102A22-22P(73) 4 31.75 41.28 38 32.6
1 3/8-18UNEF-2A
120-0109-2 73 H/MS3102A24-10P(73) 7 34.92 44.45 3.75 21 31.6 41 36
1 1/2-18UNEF-2A
TÜV approved products
HRS No. Part No. No. of contacts A B ØC D E F G ØH I
120-0231-6 73 H/MS3102A10SL-3P-C-T(73) 3 18.26 25.4
3.3
14.5 2.2 23.6 28.3 15.6
5/8-24UNEF-2A
120-0259-5 73 H/MS3102A18-10P-D-T1(73) 426.97 34.92 19.3 2.8
30 35 26.6
1 1/8-18UNEF-2A
120-0227-9 73 H/MS3102A22-22P-D-T(73) 31.75 41.28 29.4 38 32.6
1 3/8-18UNEF-2A
120-0228-1 73 H/MS3102A24-10P-G-T(73) 7 34.92 44.45 3.75 21 31.6 41 36
1 1/2-18UNEF-2A
A
B
A
B
ØC
F
DE
G
ØH
I
１８
−
１０
Ｙ
ＣＢ
Ａ
Ｄ
Ｘ
(Representative example)
H/MS3102A18-10P-D-T1(73)
5
H/MS Series●Circular Connectors Supporting TÜV and MIL spec.
Contact
Male contact
Type HRS No. Part No. Applicable wire
size
Reel contacts 120-0533-5 H/MS-PC1-212
AWG#24 〜28
Loose piece
contacts 120-0534-8 H/MS-PC1-112
(Note) Reel contacts are packaged 7,000 pcs/reel. Loose piece contacts
are packaged 100 pcs/pack.
Standard products
HRS No. Part No. No. of
contacts A B ØC D E F G ØH I
120-0501-9 73 H/MS3102A20-29PC(73) 17 29.36 38.1 3.3 19.3 2.8 29.4 37 29.6 1 1/4-18UNEF-2A
120-0502-1 73 H/MS3102A22-14PC(73) 19 31.75 41.28 32.6 1 3/8-18UNEF-2A
Receptacle (crimp type)
Receptacle mounting method
When installing a waterproof receptacle, please insert the appropriate O-ring (to be placed between the receptacle and
panel), as shown in the figure on the right.
Recommended O-ring dimensions.
Part No. ØA Inner diameter
of O-ring (Ø)
Thickness of
O-ring (Ø)
H/MS3102A10SL-** 17.5 17.5 1.5
H/MS3102A18-** 28.5 28.5
2
H/MS3102A20-** 31.5 31.5
H/MS3102A22-** 34.5 34.5
H/MS3102A-24 ** 37.8 37.5
A
B
A
B
ØC
F
DE
G
ØH
I
Ａ
Ｂ
Ｃ
Ｄ
Ｅ
Ｆ
Ｇ
Ｈ
Ｊ
Ｋ
Ｍ
Ｌ
Ｒ
Ｓ
Ｎ
ＴＰ
Ｚ
Ｗ
２０−２９Ｐ
28.5
Ø2.8
H/MS connector
Mounting panel
O-ring
ØA
(Representative example)
H/MS3102A20-29PC(73)
6
H/MS Series●Circular Connectors Supporting TÜV and MIL spec.
C
B
ØA
ØD
Spanner/wrench
flat width (mm)
E
Cord clamp
Waterproof type
HRS No. Part No. ØA B C ØD E
Range of applicable cable
diameters (reference)
Applicable shell
size
120-0801-2 73 H/MS3057-4A(73) 20 26.8 83.8 5.6 17 Ø3.1 〜5.6 10SL
120-0802-5 73 H/MS3057-10A(73) 30 28.8 72.8 14.3 27 Ø10.3 〜14.3 18
120-0803-8 73 H/MS3057-12A(73) 34 29.8 70.8 15.9 30 Ø11.4 〜15.9 20.22
120-0804-0 73 H/MS3057-16A(73) 40 33.8 69.3 19 36 Ø14 〜19 24
(Remarks) For various cable diameters, clamping force and waterproof performance may differ depending on the cable type
selected. Please make sure all specifi cations are met before assembly.
Applicable tools
Type Item HRS No. Part No. Applicable contact Applicable wire size
Manual Manual
crimping tool 150-0206-0 H/MS/CC-HT H/MS-PC1-112 AWG#24 〜28
Auto
Automatic
crimping press 901-0005-4 CM-105 ---------------------- ----------------------
Applicator 901-2027-8 AP105-H/MS-PC1-1 H/MS-PC1-212 AWG#24 〜28
Extraction tool 150-0076-7 H/MS-TP H/MS-PC1-112 ----------------------
H/MS-PC1-212
Manual crimping tool
Extraction tool Automatic crimping press (CM-105)
(Representative example)
H/MS3057-10A(73)
7
H/MS Series●Circular Connectors Supporting TÜV and MIL spec.
Connector combinations
(Remarks) 1. Illustration represents connectors for fl exible conduit and cabtire cable as a reference example.
2. The standard and TÜV approved products are compatible with each other.
When using the TÜV approved products for TÜV applications, make sure to use both TÜV approved plugs and
receptacles together.
Cord clamp
Right-angled plug
Straight plug
Low-height, right-angled plug
Single block
Receptacle
Connector for cabtire cable
Connector for fl exible conduit
Straight connector for flexible
conduit and cabtire cable
Straight connector for fl exible
conduit and cabtire cable
8
H/MS Series●Circular Connectors Supporting TÜV and MIL spec.
Table of compatibilities for H/MS connectors and the connectors for conduit and cabtire cable
Connectors for flexible conduit
H/MS connector
Part No.
Part number by Nippon Flex Co., Ltd. Part number by Daiwa Dengyo Co., Ltd.
Straight type Right angle type Straight type Right angle
type
H/MS3106A10SL-□□(73) RCC10*CA12 (with O-ring)
--------- NBDC 12S** (with O-ring) ---------
H/MS3108B10SL-□□(73) RCC10*CA12
NBDC 12S**
H/MS3106A10SL-□□(76) RCC10*RL-MS10F
RCC-30
*
RL-MS10F
BOS 10*BOL 10*
H/MS3106A18-□□(73) RCC10*CA18 (with O-ring)
--------- NBDC 18** (with O-ring) ---------
H/MS3108B18-□□(73) RCC10*CA18
NBDC 18**
H/MS3106A18-□□(76) RCC10*RL-MS18F
RCC-30
*
RL-MS18F
BOS 18** BOL 18**
H/MS3106A20-□□(73) RCC10*CA2022 (with O-ring)
--------- NBDC 20(22)** (with O-ring) ---------
H/MS3106B20-□□(73) RCC10*CA2022
NBDC 20(22)**
H/MS3106A20-□□(76) RCC10*RL-MS20F
RCC-30
*
RL-MS20F
BOS 22** BOL 20**
H/MS3106A22-□□(73) RCC10*CA2022 (with O-ring)
--------- NBDC 20(22)** (with O-ring) ---------
H/MS3108B22-□□(73) RCC10*CA2022
NBDC 20(22)
H/MS3106A22-□□(76) RCC10*RL-MS22F
RCC-30
*
RL-MS22F
BOS 22** BOL 22**
H/MS3106A24-□□(73) CC10*CA2428 (with O-ring)
--------- NBDC 24** (with O-ring) ---------
H/MS3108B24-□□(73) RCC10*CA2428
NBDC 24**
H/MS3106A24-□□(76) RCC10*RL-M524F
RCC-30
*
RL-MS24F
BOS 24** BOL 24**
Connectors for cabtire cable
H/MS connector
Part No.
Part number by Nippon Flex Co., Ltd. Part number by Daiwa Dengyo Co., Ltd.
Straight type Right angle type Straight type Right angle
type
H/MS3106A-10SL□□(73)
--------- --------- YDC 12S* (with O-ring) ---------
H/MS3108B-10SL□□(73)
YDC 12S*
H/MS3106A-10SL□□(76) ACS**RL-MS10F
ACA**RL-MS10F YDO 10*YLO 10*
H/MS3106A18-□□(73) ACS**CA18
--------- YDC 18** (with O-ring) ---------
H/MS3108B18-□□(73)
YDC 18**
H/MS3106A18-□□(76) ACS**RL-MS18F
ACA**RL-MS18F YDO 18** YLO 18*
H/MS3106A20-□□(73) ACS**CA2022
--------- YDO 20(22)** (with O-ring) ---------
H/MS3106B20-□□(73)
YDC 20(22)**
H/MS3106A20-□□(76) ACS**RL-MS20F
ACA**RL-MS20F YDC 20** YLO 20*
H/MS3106A22-□□(73) ACS**CA2022
--------- YDC 20(22)** (with O-ring) ---------
H/MS3108B22-□□(73)
YDC 20(22)**
H/MS3106A22-□□(76) ACS**RL-MS22F
ACA**RL-MS22F YDO 22** YLO 22*
H/MS3106A24-□□(73) ACS**CA2428
--------- YDC 24** (with O-ring) ---------
H/MS3108B24-□□(73)
YDC 24**
H/MS3106A24-□□(76) ACS**RL-MS24F
ACA**RL-MS24F YDO 24** YLO 24*
(Remarks) 1. □□ : Indicates contact arrangement/count.
2. **: The values differ depending on the cable used.
9
H/MS Series●Circular Connectors Supporting TÜV and MIL spec.
Contact arrangement and electrical performance
Shell size 10SL 18 20
Contact
arrangement
4 3 10 15 29
Number of
contacts 234717
Withstanding
voltage
AC 1,000 V
for one minute
AC 2,000 V
for one minute
Current
capacity 13A(24.5A) 13A(34.5A) 23A(76.2A) 23A(105.7A) 13A(44.2A)
Insulation
resistance 5,000 Mø min. at 500V DC
Contact
resistance 5 mø max. 3 mø max. 5 mø max.
Inner diameter
of solder pot Ø1.8 Ø2.9 Ø1.8
Preliminary
soldering Not necessary Needed Not necessary
Shell size 22 24
Contact
arrangement
14 22 23 10
Number of
contacts 19487
Withstanding
voltage
AC 2,000 V
for one minute
Current
capacity 13A(49.4A) 46A(152.5A) 23A(100.4A) 46A(211.5A)
Insulation
resistance 5,000 Mø min. at 500 V DC
Contact
resistance 5 mø max. 1 mø max. 3 mø max. 1 mø max.
Inner diameter
of solder pot Ø1.8 Ø5.3 Ø2.9 Ø5.3
Preliminary
soldering Not necessary Needed
Remarks
1. Figure shows the receptacle contact arrangement as viewed from the interface mating side (plug's socket insert side).
2. Withstanding voltages are derived from test voltages
3. Current capacities are shown in a value per contact. The number in ( ) indicates the connector's total capacity.
4. Contact resistances are shown in a value when measured at DC 1 A.
5. Please contact us for more information.
10
H/MS Series●Circular Connectors Supporting TÜV and MIL spec.
Major specifi cations of TÜV approved products
Applicable German standard: DIN VDE0627 (connector)
Shell size 10SL 18 22 24
Contact arrangement
3102210
Number of contacts 3 4 4 7
Ground contact No. C D D G
AC/DC rated voltage
(V) 200 500 250 500 250 250
Rated current (A) 7 10 13 17 23 17 23 23 35 46 23 35 46 23 46
Wire size (mm2) 0.5 0.75 1.25 23233.55.583.55.58 3.5 5.5
Degree of Pollution 3 2 3 2 3 2
Conducting voltage
category Ⅲ ⅡⅢⅡⅢ Ⅱ
Inner diameter of
solder pot (mm) Ø1.8 Ø2.6 Ø4.5 Plug: Ø3.6
Receptacle: Ø5.3
Remarks
1. Figure shows the receptacle contact arrangement as viewed from the interface mating side (plug's socket insert side).
2. Current capacities are shown in a value per contact.
3. The contact numbers with a mark " ◎" have contacts that are grounded to the outer shell, except for receptacles that are size
24-10.
4. For the receptacles that are size 20-10, the ground contact (contact No.: G) does not ground with the outer shell. Please use
these connectors after grounding the outer shell of the connector with the corresponding contact No.
5. The degree of pollution and conducting voltage categories refer to the environmental condition in which a DIN VDE0110
(insulation coordination for the electric appliances in a constant voltage facility) electric appliance is used, and to the class of
over voltage in the electric appliance.
6. Performance values for other than those shown above are the same as those of the general H/MS series.
Usage Recommendations
(1) The power to the circuit should always be off before mating/unmating a connector.
(2) Always use a female connector for the power side of the circuit; this will prevent the likelihood of electric shocks.
(3) Be sure to fully tighten the lock mechanism of the connectors.
(4) Connector performance features such as cable clamping force, cable rotation force, or waterproof performance may differ
depending on the cable construction. Please make sure all specifi cations are met before assembly.
(5) This product uses silver-plated contacts. Please be aware that silver easily reacts to sulfur gases, causing discoloration or
degradation when exposed to certain environmental conditions as shown below. These conditions include areas with:
• A large amount of dust and dirt
• High density of sulfur dioxide gas, hydrogen sulfi de gas, nitrogen dioxide gas, or other gas (Emission gases from vehicles
and factories, etc.)
• Highly fl uctuating temperatures, such as close to a heating apparatus
In addition, it is recommended to store the products in their original packaging or similar state in order to prevent
discoloration.
• Temperature: -10 to +60°C, relative humidity: 80% or lower (An environment where temperature and relative humidity are
constant and there is less temperature difference is recommended.)
• Please use the products within six months after delivery.
(For the products in which the storage period is expired, please confirm the ease of soldering for your application
beforehand.)
11
H/MS Series●Circular Connectors Supporting TÜV and MIL spec.
The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use.
The contents of this catalog are current as of date of 11/2014. Contents are subject to change without notice for the purpose of improvements.
2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN
TEL: +81-45-620-3526 Fax: +81-45-591-3726
http://www.hirose.com
http://www.hirose-connectors.com
®
USA:
HIROSE ELECTRIC (U.S.A.), INC. SAN JOSE OFFICE
3255 Scott Boulevard, Building 7, Suite 101
Santa Clara, CA 95054
Phone : +1-408-253-9640
Fax : +1-408-253-9641
http://www.hirose.com/us/
USA:
HIROSE ELECTRIC (U.S.A.), INC. CHICAGO OFFICE
580 Waters Edge Lane, Suite 205 Lombard IL
60148
Phone : +1-630-282-6706
Mail : inquiries@hirose.com
http://www.hirose.com/us/
USA:
HIROSE ELECTRIC (U.S.A.), INC. HEADQUARTERS
2688 Westhills Court, Simi Valley, CA 93065-6235
Phone : +1-805-522-7958
Fax : +1-805-522-3217
http://www.hirose.com/us/
HONG KONG:
HIROSE ELECTRIC HONGKONG TRADING CO., LTD.
Room 1001, West Wing, Tsim Sha Tsui Centre, 66
Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong
Phone : +852-2803-5338
Fax : +852-2591-6560
http://www.hirose.com/hk/
CHINA:
HIROSE ELECTRIC (SHANGHAI) CO.,LTD. BEIJING BRANCH
A1001, Ocean International Center, Building 56# East 4th
Ring Middle Road, ChaoYang District, Beijing, 100025
Phone : +86-10-5165-9332
Fax : +86-10-5908-1381
http://www.hirose.com/cn/
TAIWAN:
HIROSE ELECTRIC TAIWAN CO., LTD.
103 8F, No.87, Zhengzhou Rd., Taipei
Phone : +886-2-2555-7377
Fax : +886-2-2555-7350
http://www.hirose.com/cn/
GERMANY:
HIROSE ELECTRIC EUROPE B.V. GERMAN BRANCH
Herzog-Carl-Strasse 4 D-73760 Ostfildern
(Scharnhauser Park)
Phone : +49-711-4560-02-1
Fax : +49-711-4560-02-299
http://www.hirose.com/eu/
GERMANY:
HIROSE ELECTRIC EUROPE B.V. NUERNBERG OFFICE
Muggenhofer Str. 136 90429 Nuernberg
Phone : +49-911 32 68 89 63
Fax : +49-911 32 68 89 69
http://www.hirose.com/eu/
INDIA:
HIROSE ELECTRIC SINGAPORE PTE. LTD. BANGALORE LIAISON OFFICE
Unit No.03, Ground Floor, Explorer Building International Tech
Park Whitefield Road, Bangalore 560066 Karnataka, India
Phone : +91-80-4120 1907
Fax : +91-80-4120 9908
http://www.hirose.com/sg/
SINGAPORE:
HIROSE ELECTRIC SINGAPORE PTE. LTD.
10 Anson Road #26-1, International Plaza
079903, Singapore
Phone : +65-6324-6113
Fax : +65-6324-6123
http://www.hirose.com/sg/
THE NETHERLANDS:
HIROSE ELECTRIC EUROPE B.V.
Hogehillweg #8 1101 CC Amsterdam Z-O
Phone : +31-20-6557460
Fax : +31-20-6557469
http://www.hirose.com/eu/
UNITED KINGDOM:
HIROSE ELECTRIC EUROPE BV (UK BRANCH)
4 Newton Court, Kelvin Drive, Knowlhill,
Milton Keynes, MK5 8NH
Phone : +44-1908 202050
Fax : +44-1908 202058
http://www.hirose.com/eu/
USA:
HIROSE ELECTRIC (U.S.A.), INC. DETROIT OFFICE (AUTOMOTIVE)
37677 Professional Center Drive, Suite #100C
Livonia, MI 48154
Phone : +1-734-542-9963
Fax : +1-734-542-9964
http://www.hirose.com/us/
CHINA:
HIROSE ELECTRIC (SHANGHAI) CO., LTD.
1601, Henderson Metropolitan, NO.300, East Nanjing
Road, Huangpu District, Shanghai, China 200001
Phone : +86-21-6391-3355
Fax : +86-21-6391-3335
http://www.hirose.com/cn/
CHINA:
HIROSE ELECTRIC TECHNOLOGIES (SHENZHEN) CO., LTD.
Room 09-13, 19/F, Office Tower Shun Hing Square, Di Wang Commercial Centre,
5002 Shen Nan Dong Road, Shenzhen City, Guangdong Province, 518008
Phone : +86-755-8207-0851
Fax : +86-755-8207-0873
http://www.hirose.com/cn/
KOREA:
HIROSE KOREA CO., LTD.
1261-10, Jeoungwhang-Dong, Shihung-City,
Kyunggi-Do 429-450
Phone : +82-31-496-7000,7124
Fax : +82-31-496-7100
http://www.hirose.co.kr/
INDIA:
HIROSE ELECTRIC SINGAPORE PTE. LTD. DELHI LIAISON OFFICE
Office NO.519, Regus-Green Boulevard, Level5, Tower C,
Sec62, Plot B-9A, Block B, Noida, 201301, Uttar Pradesh, India
Phone : +91-12-660-8018
Fax : +91-120-4804949
http://www.hirose.com/sg/
MALAYSIA:
HIROSE ELECTRIC SINGAPORE PTE. LTD. (REPRESENTATIVE OFFICE)
1-10-07, Suntech @ Penang Cybercity (1164),Lintang
Mayang Pasir 3,11950, Bayan Baru, Penang, Malaysia.
Phone : +604-619-2564
Fax : +604-619-2574
http://www.hirose.com/sg/
12
H/MS Series●Circular Connectors Supporting TÜV and MIL spec.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Hirose Electric:
H/MS3057-4A(73) H/MS3057-12A1(73) H/MS3057-16A(73) H/MS3057-4A1(73) H/MS-PC1-112 H/MS-PC1-212
H/MS-SC-112 H/MS3057-10A(73) H/MS3057-12A(73) H/MS3057-4A H/MS-TP H/MS/CC-HT FM Crimper105-H/MS
WI Crimper 105-H/MS AP105-H/MS-PC1-1 AP105-H/MS-PC1-1(66) AP105-H/MS-PC1-1(63) AP105-H/MS-SC-212
AP105-H/MS-PC1-1(65) WI Anvil 105-H/MS AP105-H/MS-PC1-1(61) AP105-H/MS-PC1-1(68) AP105-H/MS-PC1-
1(67) AP105-H/MS-PC1-1(90) AP105-H/MS-PC1-1(64) AP105-H/MS-PC1-1(62)