DS75176B,DS75176BT
DS75176B/DS75176BT Multipoint RS-485/RS-422 Transceivers
Literature Number: SNLS381B
DS75176B/DS75176BT
Multipoint RS-485/RS-422 Transceivers
General Description
The DS75176B is a high speed differential TRI-STATE®
bus/line transceiver designed to meet the requirements of
EIA standard RS485 with extended common mode range
(+12V to −7V), for multipoint data transmission. In addition, it
is compatible with RS-422.
The driver and receiver outputs feature TRI-STATE capabil-
ity, for the driver outputs over the entire common mode
range of +12V to −7V. Bus contention or fault situations that
cause excessive power dissipation within the device are
handled by a thermal shutdown circuit, which forces the
driver outputs into the high impedance state.
DC specifications are guaranteed over the 0 to 70˚C tem-
perature and 4.75V to 5.25V supply voltage range.
Features
nMeets EIA standard RS485 for multipoint bus
transmission and is compatible with RS-422.
nSmall Outline (SO) Package option available for
minimum board space.
n22 ns driver propagation delays.
nSingle +5V supply.
n−7V to +12V bus common mode range permits ±7V
ground difference between devices on the bus.
nThermal shutdown protection.
nHigh impedance to bus with driver in TRI-STATE or with
power off, over the entire common mode range allows
the unused devices on the bus to be powered down.
nPin out compatible with DS3695/A and SN75176A/B.
nCombined impedance of a driver output and receiver
input is less than one RS485 unit load, allowing up to 32
transceivers on the bus.
n70 mV typical receiver hysteresis.
Connection and Logic Diagram
00875901
Top View
Order Number DS75176BN, DS75176BTN, DS75176BM or DS75176BTM
See NS Package Number N08E or M08A
TRI-STATE®is a registered trademark of National Semiconductor Corp.
July 2004
DS75176B/DS75176BT Multipoint RS-485/RS-422 Transceivers
© 2004 National Semiconductor Corporation DS008759 www.national.com
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage, V
CC
7V
Control Input Voltages 7V
Driver Input Voltage 7V
Driver Output Voltages +15V/ −10V
Receiver Input Voltages (DS75176B) +15V/ −10V
Receiver Output Voltage 5.5V
Continuous Power Dissipation @
25˚C
for M Package 675 mW (Note 5)
for N Package 900 mW (Note 4)
Storage Temperature Range −65˚C to +150˚C
Lead Temperature
(Soldering, 4 seconds) 260˚C
ESD Rating (HBM) 500V
Recommended Operating
Conditions
Min Max Units
Supply Voltage, V
CC
4.75 5.25 V
Voltage at Any Bus Terminal −7 +12 V
(Separate or Common Mode)
Operating Free Air Temperature T
A
DS75176B 0 +70 ˚C
DS75176BT −40 +85 ˚C
Differential Input Voltage,
VID (Note 6) −12 +12 V
Electrical Characteristics (Notes 2, 3)
0˚C T
A
70˚C, 4.75V <V
CC
<5.25V unless otherwise specified
Symbol Parameter Conditions Min Typ Max Units
V
OD1
Differential Driver Output I
O
=0 5 V
Voltage (Unloaded)
V
OD2
Differential Driver Output (Figure 1) R=50; (RS-422) (Note 7) 2 V
Voltage (with Load) R = 27; (RS-485) 1.5 V
V
OD
Change in Magnitude of Driver
Differential Output Voltage For 0.2 V
Complementary Output States
V
OC
Driver Common Mode Output (Figure 1) R=273.0 V
Voltage
|V
OC
| Change in Magnitude of Driver
Common Mode Output Voltage 0.2 V
For Complementary Output
States
V
IH
Input High Voltage 2V
V
IL
Input Low Voltage DI, DE, 0.8
V
CL
Input Clamp Voltage RE , E I
IN
= −18 mA −1.5
I
IL
Input Low Current V
IL
= 0.4V −200 µA
I
IH
Input High Current V
IH
= 2.4V 20 µA
I
IN
Input DO/RI, DO/RI V
CC
= 0V or 5.25V V
IN
= 12V +1.0 mA
Current DE = 0V V
IN
= −7V −0.8 mA
V
TH
Differential Input Threshold −7V V
CM
+ 12V −0.2 +0.2 V
Voltage for Receiver
V
TH
Receiver Input Hysteresis V
CM
=0V 70 mV
V
OH
Receiver Output High Voltage I
OH
= −400 µA 2.7 V
V
OL
Output Low Voltage RO I
OL
= 16 mA (Note 7) 0.5 V
I
OZR
OFF-State (High Impedance) V
CC
= Max ±20 µA
Output Current at Receiver 0.4V V
O
2.4V
R
IN
Receiver Input Resistance −7V V
CM
+12V 12 k
I
CC
Supply Current No Load Driver Outputs Enabled 55 mA
(Note 7) Driver Outputs Disabled 35 mA
DS75176B/DS75176BT
www.national.com 2
Electrical Characteristics (Notes 2, 3) (Continued)
0˚C T
A
70˚C, 4.75V <V
CC
<5.25V unless otherwise specified
Symbol Parameter Conditions Min Typ Max Units
I
OSD
Driver Short-Circuit V
O
= −7V (Note 7) −250 mA
Output Current V
O
= +12V (Note 7) +250 mA
I
OSR
Receiver Short-Circuit V
O
= 0V −15 −85 mA
Output Current
Note 1: “Absolute Maximum Ratings” are those beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should
be operated at these limits. The tables of “Electrical Characteristics” provide conditions for actual device operation.
Note 2: All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless otherwise specified.
Note 3: All typicals are given for VCC = 5V and TA= 25˚C.
Note 4: Derate linearly at 5.56 mW/˚C to 650 mW at 70˚C.
Note 5: Derate linearly @6.11 mW/˚C to 400 mW at 70˚C.
Note 6: Differential - Input/Output bus voltage is measured at the noninverting terminal A with respect to the inverting terminal B.
Note 7: All worst case parameters for which note 7 is applied, must be increased by 10% for DS75176BT. The other parameters remain valid for −40˚C <TA
<+85˚C.
Switching Characteristics
V
CC
= 5.0V, T
A
= 25˚C
Symbol Parameter Conditions Min Typ Max Units
t
PLH
Driver Input to Output R
LDIFF
=6012 22 ns
t
PHL
Driver Input to Output C
L1
=C
L2
= 100 pF 17 22 ns
t
r
Driver Rise Time R
LDIFF
=6018 ns
t
f
Driver Fall Time C
L1
=C
L2
= 100 pF 18 ns
(Figure 3 and Figure 5)
t
ZH
Driver Enable to Output High C
L
= 100 pF (Figure 4 and Figure 6)S1
Open
29 100 ns
t
ZL
Driver Enable to Output Low C
L
= 100 pF (Figure 4 and Figure 6)S2
Open
31 60 ns
t
LZ
Driver Disable Time from Low C
L
=15pF(Figure 4 and Figure 6)S2
Open
13 30 ns
t
HZ
Driver Disable Time from High C
L
=15pF(Figure 4 and Figure 6)S1
Open
19 200 ns
t
PLH
Receiver Input to Output C
L
=15pF(Figure 2 and Figure 7)3037ns
t
PHL
Receiver Input to Output S1 and S2 Closed 32 37 ns
t
ZL
Receiver Enable to Output Low C
L
=15pF(Figure 2 and Figure 8)S2
Open
15 20 ns
t
ZH
Receiver Enable to Output High C
L
=15pF(Figure 2 and Figure 8)S1
Open
11 20 ns
t
LZ
Receiver Disable from Low C
L
=15pF(Figure 2 and Figure 8)S2
Open
28 32 ns
t
HZ
Receiver Disable from High C
L
=15pF(Figure 2 and Figure 8)S1
Open
13 35 ns
DS75176B/DS75176BT
www.national.com3
AC Test Circuits
Switching Time Waveforms
00875902
FIGURE 1.
00875903
Note: S1 and S2 of load circuit are closed except as otherwise mentioned.
FIGURE 2.
00875904
FIGURE 3.
00875905
Note: Unless otherwise specified the switches are closed.
FIGURE 4.
00875906
FIGURE 5. Driver Propagation Delays and Transition Times
DS75176B/DS75176BT
www.national.com 4
Switching Time Waveforms (Continued)
00875907
FIGURE 6. Driver Enable and Disable Times
00875908
Note: Differential input voltage may may be realized by grounding RI and pulsing RI between +2.5V and −2.5V
FIGURE 7. Receiver Propagation Delays
00875909
FIGURE 8. Receiver Enable and Disable Times
DS75176B/DS75176BT
www.national.com5
Function Tables
DS75176B Transmitting
Inputs Line Outputs
RE DE DI Condition DO DO
X 1 1 No Fault 0 1
X 1 0 No Fault 1 0
X0X X ZZ
X 1 X Fault Z Z
DS75176B Receiving
Inputs Outputs
RE DE RI-RI RO
00 +0.2V 1
00 −0.2V 0
0 0 Inputs Open** 1
10 X Z
X Don’t care condition
Z High impedance state
Fault Improper line conditons causing excessive power dissipation in the driver, such as shorts or bus contention
situations
**This is a fail safe condition
Typical Application
00875911
DS75176B/DS75176BT
www.national.com 6
Physical Dimensions inches (millimeters)
unless otherwise noted
Lit. # 103669
Molded Dual-In-Line Package (N)
Order Number DS75176BN or DS75176BTN
NS Package Number N08E
DS75176B/DS75176BT
www.national.com7
Notes
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification
(CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Support Center
Email: ap.support@nsc.com
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
DS75176B/DS75176BT Multipoint RS-485/RS-422 Transceivers
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TIs terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TIs standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated