The MC74AC74/74ACT74 is a dual D-type flip-flop with Asynchronous Clear and Set inputs and complementary (Q,Q) outputs. Information at the input is transferred to the outputs on the positive edge of the clock pulse. Clock triggering occurs at a voltage level of the clock pulse and is not directly related to the transition time of the positive-going pulse. After the Clock Pulse input threshold voltage has been passed, the Data input is locked out and information present will not be transferred to the outputs until the next rising edge of the Clock Pulse input. Asynchronous Inputs: LOW input to SD (Set) sets Q to HIGH level LOW input to CD (Clear) sets Q to LOW level Clear and Set are independent of clock Simultaneous LOW on CD and SD makes both Q and Q HIGH * Outputs Source/Sink 24 mA * ACT74 Has TTL Compatible Inputs VCC 14 CD2 13 D2 12 CP2 11 CD1 D1 Q1 CP1 S Q D1 1 SD2 10 Q2 9 DUAL D-TYPE POSITIVE EDGE-TRIGGERED FLIP-FLOP N SUFFIX CASE 646-06 PLASTIC Q2 8 SD2 CP2 Q2 D2 C Q D2 2 PIN NAMES 1 2 3 4 5 6 7 CD1 D1 CP1 SD1 Q1 Q1 GND D1, D2 CP1, CP2 CD1, CD2 SD1, SD2 Q1, Q1, Q2, Q2 Data Inputs Clock Pulse Inputs Direct Clear Inputs Direct Set Inputs Outputs D SUFFIX CASE 751A-03 PLASTIC LOGIC SYMBOL TRUTH TABLE (Each Half) Inputs Outputs SD CD CP D Q Q L H L H H H H L L H H H X X X X X X H L X H L H H L Q0 L H H L H Q0 L Q1 SD1 D1 Q1 CD1 CP1 Q2 SD2 D2 CP2 H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial = LOW-to-HIGH Clock Transition Q0(Q0) = Previous Q(Q) before LOW-to-HIGH Transition of Clock FACT DATA 5-1 Q2 CD2 MC74AC74 MC74ACT74 LOGIC DIAGRAM SD D Q CP Q CD Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays. MAXIMUM RATINGS* Symbol Parameter Value Unit -0.5 to +7.0 V V VCC DC Supply Voltage (Referenced to GND) Vin DC Input Voltage (Referenced to GND) -0.5 to VCC +0.5 Vout DC Output Voltage (Referenced to GND) -0.5 to VCC +0.5 V Iin DC Input Current, per Pin 20 mA Iout DC Output Sink/Source Current, per Pin 50 mA ICC DC VCC or GND Current per Output Pin 50 mA Tstg Storage Temperature -65 to +150 C * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC Supply Voltage Vin, Vout DC Input Voltage, Output Voltage (Ref. to GND) tr, tf Input Rise and Fall Time (Note 1) AC Devices except Schmitt Inputs Min Typ Max AC 2.0 5.0 6.0 ACT 4.5 5.0 5.5 0 VCC VCC @ 3.0 V 150 VCC @ 4.5 V 40 VCC @ 5.5 V 25 VCC @ 4.5 V 10 VCC @ 5.5 V 8.0 Unit V V ns/V tr, tf Input Rise and Fall Time (Note 2) ACT Devices except Schmitt Inputs TJ Junction Temperature (PDIP) TA Operating Ambient Temperature Range 85 C IOH Output Current -- High -24 mA IOL Output Current -- Low 24 mA ns/V 140 -40 1. Vin from 30% to 70% VCC; see individual Data Sheets for devices that differ from the typical input rise and fall times. 2. Vin from 0.8 V to 2.0 V; see individual Data Sheets for devices that differ from the typical input rise and fall times. FACT DATA 5-2 25 C MC74AC74 MC74ACT74 DC CHARACTERISTICS Symbol Parameter VCC (V) 74AC 74AC TA = +25C TA = -40C to +85C Typ VIH VIL VOH 1.5 2.25 2.75 2.1 3.15 3.85 2.1 3.15 3.85 V VOUT = 0.1 V or VCC - 0.1 V Maximum Low Level Input Voltage 3.0 4.5 5.5 1.5 2.25 2.75 0.9 1.35 1.65 0.9 1.35 1.65 V VOUT = 0.1 V or VCC - 0.1 V Minimum High Level Output Voltage 3.0 4.5 5.5 2.99 4.49 5.49 2.9 4.4 5.4 2.9 4.4 5.4 V 2.56 3.86 4.86 2.46 3.76 4.76 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 5.5 0.36 0.36 0.36 0.44 0.44 0.44 5.5 0.1 3.0 4.5 5.5 Maximum Low Level Output Voltage Maximum Input Leakage Current IOLD Minimum Dynamic Output Current ICC Guaranteed Limits 3.0 4.5 5.5 IIN IOHD Conditions Minimum High Level Input Voltage 3.0 4.5 5.5 VOL Unit Maximum Quiescent Supply Current 0.002 0.001 0.001 IOUT = -50 A *VIN = VIL or VIH -12 mA IOH -24 mA -24 mA V IOUT = 50 A V V *VIN = VIL or VIH 12 mA IOL 24 mA 24 mA 1.0 A VI = VCC, GND 5.5 75 mA VOLD = 1.65 V Max 5.5 -75 mA VOHD = 3.85 V Min 40 A VIN = VCC or GND 5.5 4.0 * All outputs loaded; thresholds on input associated with output under test. Maximum test duration 2.0 ms, one output loaded at a time. Note: IIN and ICC @ 3.0 V are guaranteed to be less than or equal to the respective limit @ 5.5 V VCC. AC CHARACTERISTICS (For Figures and Waveforms -- See Section 3) Symbol Parameter VCC* (V) 74AC 74AC TA = +25C CL = 50 pF TA = -40C to +85C CL = 50 pF Min Typ Max Min Unit Fig. No. MHz 3-3 Max fmax Maximum Clock Frequency 3.3 5.0 100 140 125 160 tPLH Propagation Delay CDn or SDn to Qn or Qn 3.3 5.0 5.0 3.5 8.0 6.0 12.5 9.0 4.0 3.0 13.0 10.0 ns 3-6 tPHL Propagation Delay CDn or SDn to Qn or Qn 3.3 5.0 4.0 3.0 10.5 8.0 12.0 9.5 3.5 2.5 13.5 10.5 ns 3-6 tPLH Propagation Delay CPn to Qn or Qn 3.3 5.0 4.5 3.5 8.0 6.0 13.5 10.0 4.0 3.0 16.0 10.5 ns 3-6 tPHL Propagation Delay CPn to Qn or Qn 3.3 5.0 3.5 2.5 8.0 6.0 14.0 10.0 3.5 2.5 14.5 10.5 ns 3-6 * Voltage Range 3.3 V is 3.3 V 0.3 V. Voltage Range 5.0 V is 5.0 V 0.5 V. FACT DATA 5-3 95 125 MC74AC74 MC74ACT74 AC OPERATING REQUIREMENTS Symbol VCC* (V) Parameter Typ 74AC 74AC TA = +25C CL = 50 pF TA = -40C to +85C CL = 50 pF Unit Fig. No. Guaranteed Minimum ts Set-up Time, HIGH or LOW Dn to CPn 3.3 5.0 1.5 1.0 4.0 3.0 4.5 3.0 ns 3-9 th Hold Time, HIGH or LOW Dn to CPn 3.3 5.0 -2.0 -1.5 0.5 0.5 0.5 0.5 ns 3-9 tw CPn or CDn or SDn Pulse Width 3.3 5.0 3.0 2.5 5.5 4.5 7.0 5.0 ns 3-6 trec Recovery TIme CDn or SDn to CP 3.3 5.0 -2.5 -2.0 0 0 0 0 ns 3-9 * Voltage Range 3.3 V is 3.3 V 0.3 V. Voltage Range 5.0 V is 5.0 V 0.5 V. DC CHARACTERISTICS Symbol Parameter VCC (V) 74ACT 74ACT TA = +25C TA = -40C to +85C Typ Guaranteed Limits Unit Conditions VIH Minimum High Level Input Voltage 4.5 5.5 1.5 1.5 2.0 2.0 2.0 2.0 V VOUT = 0.1 V or VCC - 0.1 V VIL Maximum Low Level Input Voltage 4.5 5.5 1.5 1.5 0.8 0.8 0.8 0.8 V VOUT = 0.1 V or VCC - 0.1 V VOH Minimum High Level Output Voltage 4.5 5.5 4.49 5.49 4.4 5.4 4.4 5.4 V 3.86 4.86 3.76 4.76 0.1 0.1 0.1 0.1 4.5 5.5 0.36 0.36 0.44 0.44 V *VIN = VIL or VIH 24 mA IOL 24 mA 0.1 1.0 A VI = VCC, GND 1.5 mA VI = VCC - 2.1 V 4.5 5.5 VOL Maximum Low Level Output Voltage 4.5 5.5 0.001 0.001 V V IOUT = -50 A *VIN = VIL or VIH -24 mA IOH -24 mA IOUT = 50 A IIN Maximum Input Leakage Current 5.5 ICCT Additional Max. ICC/Input 5.5 IOLD Minimum Dynamic Output Current 5.5 75 mA VOLD = 1.65 V Max 5.5 -75 mA VOHD = 3.85 V Min 40 A VIN = VCC or GND IOHD ICC Maximum Quiescent Supply Current 0.6 5.5 4.0 * All outputs loaded; thresholds on input associated with output under test. Maximum test duration 2.0 ms, one output loaded at a time. FACT DATA 5-4 MC74AC74 MC74ACT74 AC CHARACTERISTICS (For Figures and Waveforms -- See Section 3) Symbol Parameter VCC* (V) 74ACT 74ACT TA = +25C CL = 50 pF TA = -40C to +85C CL = 50 pF Min Typ Max Min Unit Fig. No. MHz 3-3 Max fmax Maximum Clock Frequency 5.0 145 210 tPLH Propagation Delay CDn or SDn to Qn or Qn 5.0 3.0 5.5 9.5 2.5 10.5 ns 3-6 tPHL Propagation Delay CDn or SDn to Qn or Qn 5.0 3.0 6.0 10.0 3.0 11.5 ns 3-6 tPLH Propagation Delay CPn to Qn or Qn 5.0 4.0 7.5 11.0 4.0 13.0 ns 3-6 tPHL Propagation Delay CPn to Qn or Qn 5.0 3.5 6.0 10.0 3.0 11.5 ns 3-6 Unit Fig. No. 125 * Voltage Range 5.0 V is 5.0 V 0.5 V. AC OPERATING REQUIREMENTS Symbol Parameter VCC* (V) 74ACT 74ACT TA = +25C CL = 50 pF TA = -40C to +85C CL = 50 pF Typ Guaranteed Minimum ts Set-up Time, HIGH or LOW Dn to CPn 5.0 1.0 3.0 3.5 ns 3-9 th Hold Time, HIGH or LOW Dn to CPn 5.0 -0.5 1.0 1.0 ns 3-9 tw CPn or CDn or SDn Pulse Width 5.0 3.0 5.0 6.0 ns 3-6 trec Recovery TIme CDn or SDn to CP 5.0 -2.5 0 0 ns 3-9 * Voltage Range 5.0 V is 5.0 V 0.5 V. CAPACITANCE Symbol Parameter Value Typ Unit Test Conditions CIN Input Capacitance 4.5 pF VCC = 5.0 V CPD Power Dissipation Capacitance 35 pF VCC = 5.0 V FACT DATA 5-5 MC74AC74 MC74ACT74 OUTLINE DIMENSIONS N SUFFIX PLASTIC DIP PACKAGE CASE 646-06 ISSUE L 14 NOTES: 1. LEADS WITHIN 0.13 (0.005) RADIUS OF TRUE POSITION AT SEATING PLANE AT MAXIMUM MATERIAL CONDITION. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 4. ROUNDED CORNERS OPTIONAL. 8 B 1 7 A F DIM A B C D F G H J K L M N L C J N H G D SEATING PLANE K M D SUFFIX PLASTIC SOIC PACKAGE CASE 751A-03 ISSUE F 8 -B- 1 P 7 PL 0.25 (0.010) 7 G B M M R X 45 _ C F -T- SEATING PLANE M K D 14 PL 0.25 (0.010) M T B S A S MILLIMETERS MIN MAX 18.16 19.56 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.62 BSC 0_ 10_ 0.39 1.01 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. -A- 14 INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.300 BSC 0_ 10_ 0.015 0.039 J DIM A B C D F G J K M P R MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.228 0.244 0.010 0.019 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, Toshikatsu Otsuki, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-3521-8315 MFAX: RMFAX0@email.sps.mot.com -TOUCHTONE (602) 244-6609 INTERNET: http://Design-NET.com HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 FACT DATA 5-6 *MC74AC74/D* MC74AC74/D