LMV7219M5/NOPB - NATIONAL SEMICONDUCTOR

Product

Folder

Order

Now

Technical

Documents

Tools &

Software

Support &

Community

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,

intellectual property matters and other important disclaimers. PRODUCTION DATA.

LMV7219

SNOS458I –APRIL 2000–REVISED JUNE 2016

LMV7219 7-ns 2.7-V to 5-V Comparator with Rail-to-Rail Output

1 Features

1• (VS=5V,TA= 25°C, Typical Values Unless

Specified)

• Propagation Delay 7 ns

• Low Supply Current 1.1 mA

• Input Common Mode Voltage Range Extends

200 mv Below Ground

• Ideal for 2.7-V and 5-V Single Supply Applications

• Internal Hysteresis Ensures Clean Switching

• Fast Rise and Fall Time 1.3 ns

• Available in Space-saving Packages: SC-70 and

SOT-23

• Supports 105°C PCB Temperature

2 Applications

• Portable and Battery-powered Systems

• Scanners

• Set Top Boxes

• High Speed Differential Line Receiver

• Window Comparators

• Zero-crossing Detectors

• High-speed Sampling Circuits

3 Description

The LMV7219 is a low-power, high-speed comparator

with internal hysteresis. The LMV7219 operating

voltage ranges from 2.7 V to 5 V with push-pull rail-

to-rail output. This device achieves a 7-ns

propagation delay while consuming only 1.1 mA of

supply current at 5 V.

The LMV7219 inputs have a common mode voltage

range that extends 200 mV below ground, allowing

ground sensing. The internal hysteresis ensures

clean output transitions even with slow-moving inputs

signals.

The LMV7219 is available in the SC-70 and SOT-23

packages, which are ideal for systems where small

size and low power are critical.

Device Information(1)

PART NUMBER PACKAGE BODY SIZE (NOM)

LMV7219 SC-70 (5) 2.00 mm × 1.25 mm

SOT-23 (5) 2.88 mm × 1.60 mm

(1) For all available packages, see the orderable addendum at

the end of the datasheet.

Typical Application

LMV7219

SNOS458I –APRIL 2000–REVISED JUNE 2016

www.ti.com

Product Folder Links: LMV7219

Table of Contents

1 Features.................................................................. 1

2 Applications ........................................................... 1

3 Description............................................................. 1

4 Revision History..................................................... 2

5 Pin Configuration and Functions......................... 3

6 Specifications......................................................... 4

6.1 Absolute Maximum Ratings ...................................... 4

6.2 ESD Ratings.............................................................. 4

6.3 Recommended Operating Conditions....................... 4

6.4 Thermal Information ................................................. 4

6.5 Electrical Characteristics 2.7 V ................................ 5

6.6 Electrical Characteristics 5 V ................................... 6

6.7 Typical Performance Characteristics ........................ 8

7 Detailed Description............................................ 11

7.1 Overview................................................................. 11

7.2 Functional Block Diagram....................................... 11

7.3 Feature Description................................................. 11

7.4 Device Functional Modes........................................ 11

8 Application and Implementation ........................ 12

8.1 Application Information............................................ 12

8.2 Typical Application ................................................. 12

9 Power Supply Recommendations...................... 16

10 Layout................................................................... 16

10.1 Layout Guidelines ................................................. 16

10.2 Layout Example .................................................... 17

11 Device and Documentation Support................. 18

11.1 Documentation Support ........................................ 18

11.2 Receiving Notification of Documentation Updates 18

11.3 Community Resources.......................................... 18

11.4 Trademarks........................................................... 18

11.5 Electrostatic Discharge Caution............................ 18

12 Mechanical, Packaging, and Orderable

Information........................................................... 18

4 Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from Revision H (April 2016) to Revision I Page

• Added Supports 105°C PCB Temperature to Features List................................................................................................... 1

• Changed Operating Temperature to Ambient Temperature .................................................................................................. 4

• Added Junction Temperature of 125 °C................................................................................................................................. 4

• Added PCB Temperature of 105 °C ...................................................................................................................................... 4

• Added TPCB ≤105°C throughout Electrical Tables ................................................................................................................ 5

Changes from Revision G (January 2015) to Revision H Page

• Changed "Infrared or Convection (20 sec)" from 235 °C....................................................................................................... 4

• Added thermal data for SOT23 and SC70 packages ............................................................................................................ 4

Changes from Revision F (April 2013) to Revision G Page

• Added, updated, or renamed the following sections: Device Information Table, Pin Configurations and Functions;

Specifications; Application and Implementation;Power Supply Recommendations;Layout;Device and

Documentation Support;Mechanical, Packaging, and Ordering Information ........................................................................ 1

• Changed from "transient response" to "eliminate possible output chatter" in Circuit Layout and Bypassing ..................... 16

Changes from Revision E (March 2013) to Revision F Page

• Changed layout of National Data Sheet to TI format ............................................................................................................. 1

LMV7219

www.ti.com

SNOS458I –APRIL 2000–REVISED JUNE 2016

Product Folder Links: LMV7219

5 Pin Configuration and Functions

5-Pin SC-70 and SOT-23

Packages DCK and DBV

(Top View)

Pin Functions

PIN I/O DESCRIPTION

NUMBER NAME

1 OUT O Output

2 V-I Negative Supply

3 +IN I Non-inverting input

4 -IN I Inverting input

5 V+I Positive Supply

LMV7219

SNOS458I –APRIL 2000–REVISED JUNE 2016

www.ti.com

Product Folder Links: LMV7219

(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for

which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test

conditions, see the Electrical characteristics.

(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and

specifications.

(3) Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in

exceeding the maximum allowed junction temperature of 150°C. Output currents in excess of ±30mA over long term may adversely

affect reliability.

(4) Limiting input pin current is only necessary for input voltages that exceed absolute maximum input voltage ratings.

6 Specifications

6.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted) (1)(2)

MIN MAX UNIT

Differential input voltage ± Supply Voltage

Output short circuit duration See(3)

Supply voltage (V+- V−) 5.5 V

Soldering information Infrared or Convection (20 sec) 260 °C

Wave Soldering (10 sec) 260 (lead temp) °C

Voltage at input/output pins (V+) + 0.4

(V−)−0.4 V

Current at input pin(4) ±10 mA

Maximum junction temperature 150 °C

Storage temperature −65 150 °C

(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Manufacturing with

less than 500-V HBM is possible with the necessary precautions. Pins listed as ±2000 V may actually have higher performance.

(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. Manufacturing with

less than 250-V CDM is possible with the necessary precautions. Pins listed as ±150 V may actually have higher performance.

6.2 ESD Ratings VALUE UNIT

V(ESD) Electrostatic

discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000 V

Charged-device model (CDM), per JEDEC specification JESD22-C101(2) ±150

(1) The maximum power dissipation is a function of TJ(MAX), RθJA, and TA. The maximum allowable power dissipation at any ambient

temperature is PD= (TJ(MAX) - TA)/RθJA. All numbers apply for packages soldered directly into a PC board.

6.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT

Supply voltages (V+- V−) 2.7 5 V

Ambient Temperature(1) −40 +85 °C

Junction Temperature 125 °C

PCB Temperature 105 °C

(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application

report, SPRA953.

6.4 Thermal Information

THERMAL METRIC(1) LMV7219 LMV7219

UNITDBV (SOT23) DCK (SC70)

5 PINS 5 PINS

RθJA Junction-to-ambient thermal resistance 209 296 °C/W

RθJC(top) Junction-to-case (top) thermal resistance 170 132 °C/W

RθJB Junction-to-board thermal resistance 68 76 °C/W

ψJT Junction-to-top characterization parameter 52 8.6 °C/W

LMV7219

www.ti.com

SNOS458I –APRIL 2000–REVISED JUNE 2016

Product Folder Links: LMV7219

Thermal Information (continued)

THERMAL METRIC(1) LMV7219 LMV7219

UNITDBV (SOT23) DCK (SC70)

5 PINS 5 PINS

ψJB Junction-to-board characterization parameter 68 75 °C/W

RθJC(bot) Junction-to-case (bottom) thermal resistance N/A N/A °C/W

(1) Typical Values represent the most likely parametric norm.

(2) All limits are specified by testing or statistical analysis.

(3) Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in

exceeding the maximum allowed junction temperature of 150°C. Output currents in excess of ±30mA over long term may adversely

affect reliability.

(4) The LMV7219 comparator has internal hysteresis. The trip points are the input voltage needed to change the output state in each

direction. The offset voltage is defined as the average of Vtrip+and Vtrip−, while the hysteresis voltage is the difference of these two.

6.5 Electrical Characteristics 2.7 V

Unless otherwise specified, all limits ensured for TJ= 25°C, VCM = V+/2, V+= 2.7 V, V−= 0 V, CL= 10 pF and RL> 1MΩto V−.

PARAMETER TEST CONDITIONS MIN TYP(1) MAX(2) UNIT

VOS Input offset voltage 1 6 mV

−40°C ≤TJ≤+85°C and TPCB ≤105°C 8

IBInput bias current 450 950 nA

−40°C ≤TJ≤+85°C and TPCB ≤105°C 2000

IOS Input offset current 50 200 nA

−40°C ≤TJ≤+85°C and TPCB ≤105°C 400

CMRR Common mode rejection ratio 0 V < VCM < 1.50 V 62 85 dB

−40°C ≤TJ≤+85°C

and TPCB ≤105°C 55

PSRR Power supply rejection ratio V+= 2.7 V to 5 V 65 85 dB

−40°C ≤TJ≤+85°C

and TPCB ≤105°C 55

VCM Input common-voltage range CMRR > 50 dB

VCC −1.2 VCC −1

−40°C ≤TJ≤+85°C

and TPCB ≤105°C VCC −1.3

−0.2 −0.1

−40°C ≤TJ≤+85°C

and TPCB ≤105°C 0

Output swing high

IL= 4 mA,

VID = 500 mV

VCC −0.3 VCC −0.22

−40°C ≤TJ≤+85°C

and TPCB ≤105°C VCC −0.4

IL= 0.4 mA,

VID = 500 mV

VCC −0.05 VCC −0.02

−40°C ≤TJ≤+85°C

and TPCB ≤105°C VCC −0.15

Output swing low

IL=−4 mA,

VID =−500 mV

130 200

−40°C ≤TJ≤+85°C

and TPCB ≤105°C 300

IL=−0.4 mA,

VID =−500 mV

15 50

−40°C ≤TJ≤+85°C

and TPCB ≤105°C 150

ISC Output short circuit current Sourcing, VO= 0 V(3) 20 mA

Sinking, VO= 2.7 V(3) 20

ISSupply current No Load 0.9 1.6 mA

−40°C ≤TJ≤+85°C

and TPCB ≤105°C 2.2

VHYST Input hysteresis voltage See(4) 7 mV

VTRIP+Input referred positive trip point (see Figure 19) 3 8 mV

LMV7219

SNOS458I –APRIL 2000–REVISED JUNE 2016

www.ti.com

Product Folder Links: LMV7219

Electrical Characteristics 2.7 V (continued)

Unless otherwise specified, all limits ensured for TJ= 25°C, VCM = V+/2, V+= 2.7 V, V−= 0 V, CL= 10 pF and RL> 1MΩto V−.

PARAMETER TEST CONDITIONS MIN TYP(1) MAX(2) UNIT

(5) Propagation delay measurements made with 100 mV steps. Overdrive is measured relative to VTrip.

(6) Propagation Delay Skew is defined as absolute value of the difference between tPDLH and tPDHL.

VTRIP−Input referred negative trip point (see Figure 19)−8−4 mV

tPD Propagation delay Overdrive = 5 mV, VCM = 0V(5) 12 nsOverdrive = 15 mV, VCM = 0 V(5) 11

Overdrive = 50 mV, VCM = 0 V(5) 10 20

tSKEW Propagation delay skew See(6) 1 ns

trOutput rise time 10% to 90% 2.5 ns

tfOutput fall time 90% to 10% 2 ns

(1) Typical Values represent the most likely parametric norm.

(2) All limits are specified by testing or statistical analysis.

6.6 Electrical Characteristics 5 V

Unless otherwise specified, all limits ensured for TJ= 25°C, VCM = V+/2, V+= 5 V, V−= 0 V, CL= 10 pF and RL> 1 MΩto V−.

PARAMETER TEST CONDITIONS MIN TYP(1) MAX(2) UNIT

VOS Input offset voltage 1 6 mV

−40°C ≤TJ≤+85°C and TPCB ≤105°C 8

IBInput bias current 500 950 nA

−40°C ≤TJ≤+85°C and TPCB ≤105°C 2000

IOS Input offset current 50 200 nA

−40°C ≤TJ≤+85°C and TPCB ≤105°C 400

CMRR Common mode rejection ratio 0 V < VCM < 3.8 V 65 85 dB

−40°C ≤TJ≤+85°C

and TPCB ≤105°C 55

PSRR Power supply rejection ratio V+= 2.7 V to 5 V 65 85 dB

−40°C ≤TJ≤+85°C

and TPCB ≤105°C 55

VCM Input common-mode voltage

range CMRR > 50 dB

VCC −1.2 VCC −1V

−40°C ≤TJ≤+85°C

and TPCB ≤105°C VCC −1.3

−0.2 −0.1 V

−40°C ≤TJ≤+85°C

and TPCB ≤105°C 0

Output swing high

IL= 4 mA,

VID = 500 mV

VCC −0.2 VCC −0.13

−40°C ≤TJ≤+85°C

and TPCB ≤105°C VCC −0.3

IL= 0.4 mA,

VID = 500 mV

VCC −0.05 VCC −0.02

−40°C ≤TJ≤+85°C

and TPCB ≤105°C VCC −0.15

Output swing low

IL=−4 mA,

VID =−500 mV

80 180

−40°C ≤TJ≤+85°C

and TPCB ≤105°C 280

IL=−0.4 mA,

VID =−500 mV

10 50

−40°C ≤TJ≤+85°C

and TPCB ≤105°C 150

LMV7219

www.ti.com

SNOS458I –APRIL 2000–REVISED JUNE 2016

Product Folder Links: LMV7219

Electrical Characteristics 5 V (continued)

Unless otherwise specified, all limits ensured for TJ= 25°C, VCM = V+/2, V+= 5 V, V−= 0 V, CL= 10 pF and RL> 1 MΩto V−.

PARAMETER TEST CONDITIONS MIN TYP(1) MAX(2) UNIT

(3) Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in

exceeding the maximum allowed junction temperature of 150°C. Output currents in excess of ±30mA over long term may adversely

affect reliability.

(4) The LMV7219 comparator has internal hysteresis. The trip points are the input voltage needed to change the output state in each

direction. The offset voltage is defined as the average of Vtrip+and Vtrip−, while the hysteresis voltage is the difference of these two.

(5) Propagation delay measurements made with 100 mV steps. Overdrive is measured relative to VTrip.

(6) Propagation Delay Skew is defined as absolute value of the difference between tPDLH and tPDHL.

ISC Output short circuit current

Sourcing, VO= 0 V(3) 30 68

−40°C ≤TJ≤+85°C

and TPCB ≤105°C 20

Sinking, VO= 5 V(3) 30 65

−40°C ≤TJ≤+85°C

and TPCB ≤105°C 20

ISSupply current No Load 1.1 1.8 mA

−40°C ≤TJ≤+85°C

and TPCB ≤105°C 2.4

VHYST Input hysteresis voltage See(4) 7.5 mV

VTrip+Input referred positive trip point (See Figure 19) 3.5 8 mV

VTrip−Input referred negative trip

point (See Figure 19)−8−4 mV

tPD Propagation delay Overdrive = 5 mV, VCM = 0 V(5) 9nsOverdrive = 15 mV, VCM = 0 V(5) 8 20

Overdrive = 50 mV, VCM = 0 V(5) 7 19

tSKEW Propagation delay skew See(6) 0.4 ns

trOutput rise time 10% to 90% 1.3 ns

tfOutput fall time 90% to 10% 1.25 ns

LMV7219

SNOS458I –APRIL 2000–REVISED JUNE 2016

www.ti.com

Product Folder Links: LMV7219

6.7 Typical Performance Characteristics

Unless otherwise specified, VS= 5 V, CL= 10 pF, TA= 25°C

Figure 1. Supply Current vs. Supply Voltage Figure 2. VOS vs. Supply Voltage

Figure 3. Input Offset and Trip Voltage vs. Supply Voltage

VS= 2.7 V

Figure 4. Sourcing Current vs. Output Voltage

VS= 5 V

Figure 5. Sourcing Current vs. Output Voltage

VS= 2.7 V

Figure 6. Sinking Current vs. Output Voltage

LMV7219

www.ti.com

SNOS458I –APRIL 2000–REVISED JUNE 2016

Product Folder Links: LMV7219

Typical Performance Characteristics (continued)

Unless otherwise specified, VS= 5 V, CL= 10 pF, TA= 25°C

VS= 5 V

Figure 7. Sinking Current vs. Output Voltage

VS= 2.7 V

VOD = 15 mV

Figure 8. Propagation Delay vs. Temperature

VS= 5V

VOD = 15 mV

Figure 9. Propagation Delay vs. Temperature

VS= 5 V

VOD = 15 mV

Figure 10. Propagation Delay vs. Capacitive Load

Figure 11. Propagation Delay vs. Input Overdrive

VS= 2.7 V

CL= 10 pF

VOD = 15 mV

Figure 12. Propagation Delay (tPD−)

LMV7219

SNOS458I –APRIL 2000–REVISED JUNE 2016

www.ti.com

Product Folder Links: LMV7219

Typical Performance Characteristics (continued)

Unless otherwise specified, VS= 5 V, CL= 10 pF, TA= 25°C

VS= 2.7 V

CL= 10 pF

VOD = 15 mV

Figure 13. Propagation Delay (tPD+)

LMV7219

www.ti.com

SNOS458I –APRIL 2000–REVISED JUNE 2016

Product Folder Links: LMV7219

7 Detailed Description

7.1 Overview

LMV7219 is a single supply comparator with internal hysteresis, 7 ns of propagation delay and only 1.1 mA of

supply current.

The LMV7219 has a typical input common mode voltage range of −0.2 V below the ground to 1 V below Vcc. The

differential input stage is a pair of PNP transistors, therefore, the input bias current flows out of the device. If

either of the input signals falls below the negative common mode limit, the parasitic PN junction formed by the

substrate and the base of the PNP will turn on, resulting in an increase of input bias current.

7.2 Functional Block Diagram

7.3 Feature Description

If one of the inputs goes above the positive common mode limit, the output will still maintain the correct logic

level as long as the other input stays within the common mode range. However, the propagation delay will

increase. When both inputs are outside the common mode voltage range, current saturation occurs in the input

stage, and the output becomes unpredictable.

7.4 Device Functional Modes

The propagation delay does not increase significantly with large differential input voltages. However, large

differential voltages greater than the supply voltage should be avoided to prevent damages to the input stage.

The LMV7219 has a push-pull output. When the output switches, there is a direct path between VCC and ground,

causing high output sinking or sourcing current during the transition. After the transition, the output current

decreases and the supply current settles back to about 1.1 mA at 5 V, thus conserving power consumption.

Most high-speed comparators oscillate when the voltage of one of the inputs is close to or equal to the voltage

on the other input due to noise or undesirable feedback. The LMV7219 has 7 mV of internal hysteresis to counter

parasitic effects and noise. The hysteresis does not change significantly with the supply voltages and the

common mode input voltages as reflected in the specification table.

LMV7219

SNOS458I –APRIL 2000–REVISED JUNE 2016

www.ti.com

Product Folder Links: LMV7219

8 Application and Implementation

NOTE

Information in the following applications sections is not part of the TI component

specification, and TI does not warrant its accuracy or completeness. TI’s customers are

responsible for determining suitability of components for their purposes. Customers should

validate and test their design implementation to confirm system functionality.

8.1 Application Information

The following section explains in detail how to manipulate the hysteresis voltage of the LMV7219. Detailed

expressions are provided along with practical considerations for designing hysteresis.

8.2 Typical Application

Figure 14 shows the typical method of adding external hysteresis to a comparator. The positive feedback is

responsible for shifting the comparator trip point depending on the state of the output.

Figure 14. Additional Hysteresis

8.2.1 Design Requirements

The internal hysteresis creates two trip points, one for the rising input voltage and one for the falling input

voltage, as shown in Figure 19. The difference between the trip points is the hysteresis. With internal hysteresis,

when the comparator's input voltages are equal, the hysteresis effectively causes one comparator-input voltage

to move quickly past the other, thus taking the input out of the region where oscillation occurs. Standard

comparators require hysteresis to be added with external resistors. The fixed internal hysteresis eliminates these

resistors.

8.2.2 Detailed Design Procedure

8.2.2.1 Additional Hysteresis

If additional hysteresis is desired, this can be done with the addition of three resistors using positive feedback, as

shown in Figure 14. The positive feedback method slows the comparator response time. Calculate the resistor

values as follows:

1. Select R3. The current through R3 should be greater than the input bias current to minimize errors. The

current through R3 (IF) at the trip point is (VREF - VOUT) /R3. Consider the two possible output states when solving

for R3, and use the smaller of the two resulting resistor values. The two formulas are:

R3 = VREF/IF(1)

When VOUT = 0:

LMV7219

www.ti.com

SNOS458I –APRIL 2000–REVISED JUNE 2016

Product Folder Links: LMV7219

Typical Application (continued)

R3 = VCC - VREF /IF(2)

When VOUT = VCC:

2. Choose a hysteresis band required (VHB).

3. Calculate R1, where R1 = R3 X(VHB/VCC)

4. Choose the trip point for VIN rising. This is the threshold voltage (VTHR) at which the comparator switches from

low to high as VIN rises about the trip point.

5. Calculate R2 as follows:

(3)

6. Verify the trip voltage and hysteresis as follows:

(4)

This method is recommended for additional hysteresis of up to a few hundred millivolts. Beyond that, the

impedance of R3 is low enough to affect the bias string and adjustment of R1 may be also required.

8.2.2.2 Zero-Crossing Detector

The inverting input is connected to ground and the non-inverting input is connected to 100mVp-p signal. As the

signal at the non-inverting input crosses 0 V, the comparator's output Changes State.

Figure 15. Zero-Crossing Detector

8.2.2.3 Threshold Detector

Instead of tying the inverting input to 0 V, the inverting input can be tied to a reference voltage. The non-inverting

input is connected to the input. As the input passes the VREF threshold, the comparator's output changes state.

LMV7219

SNOS458I –APRIL 2000–REVISED JUNE 2016

www.ti.com

Product Folder Links: LMV7219

Typical Application (continued)

Figure 16. Threshold Detector

8.2.2.4 Crystal Oscillator

A simple crystal oscillator using the LMV7219 is shown in Figure 17. Resistors R1 and R2 set the bias point at

the comparator's non-inverting input. Resistors R3, R4 and C1 sets the inverting input node at an appropriate DC

average level based on the output. The crystal's path provides resonant positive feedback and stable oscillation

occurs. The output duty cycle for this circuit is roughly 50%, but it is affected by resistor tolerances and to a

lesser extent by the comparator offset.

Figure 17. Crystal Oscillator

8.2.2.5 IR Receiver

The LMV7219 is an ideal candidate to be used as an infrared receiver. The infrared photo diode creates a

current relative to the amount of infrared light present. The current creates a voltage across RD. When this

voltage level cross the voltage applied by the voltage divider to the inverting input, the output transitions.

LMV7219

www.ti.com

SNOS458I –APRIL 2000–REVISED JUNE 2016

Product Folder Links: LMV7219

Typical Application (continued)

Figure 18. IR Receiver

8.2.3 Application Curve

Figure 19. Input and Output Waveforms, Non-Inverting Input Varied

LMV7219

SNOS458I –APRIL 2000–REVISED JUNE 2016

www.ti.com

Product Folder Links: LMV7219

9 Power Supply Recommendations

The LMV7219 can operate off a single supply or with dual supplies as long as the input CM voltage range (VCM)

has the required headroom to the positive rail V+. The input range extends to slightly below V- voltage. Supplies

should be decoupled with low inductance, often ceramic, capacitors to ground less than 0.5 inches from the

device pins. The use of ground plane is recommended, and as in most high speed devices, it is advisable to

remove ground plane close to device sensitive pins such as the inputs.

10 Layout

10.1 Layout Guidelines

10.1.1 Circuit Layout and Bypassing

The LMV7219 requires high-speed layout. Follow these layout guidelines:

1. Power supply bypassing is critical, and will improve stability and eliminate possible output chatter. A

decoupling capacitor such as 0.1-µF ceramic should be placed as close as possible to V+pin (and to V- pin if

used with dual supplies) as shown in Figure 20. An additional 2.2-µF tantalum capacitor may be required for

extra noise reduction.

2. Keep all leads short to reduce stray capacitance and lead inductance. It will also minimize unwanted parasitic

feedback around the comparator.

3. The device should be soldered directly to the PC board instead of using a socket.

4. Use a PC board with a good, unbroken low inductance ground plane as shown in Figure 20. Make sure

ground paths are low-impedance, especially were heavier currents are flowing.

5. Input traces should be kept away from output traces. This can be achieved by running a topside ground

plane between the output and inputs.

6. Run the ground trace under the device up to the bypass capacitor to shield the inputs from the outputs.

7. To prevent parasitic feedback when input signals are slow-moving, a small capacitor of 1000 pF or less can

be placed between the inputs. It can also help eliminate oscillations in the transition region. However, this

capacitor can cause some degradation to tpd when the source impedance is low.

LMV7219

www.ti.com

SNOS458I –APRIL 2000–REVISED JUNE 2016

Product Folder Links: LMV7219

10.2 Layout Example

Figure 20. SOT-23 Board Layout Example

LMV7219

SNOS458I –APRIL 2000–REVISED JUNE 2016

www.ti.com

Product Folder Links: LMV7219

11 Device and Documentation Support

11.1 Documentation Support

11.1.1 Related Documentation

For related documentation, see the following:

•Absolute Maximum Ratings for Soldering (SNOA549)

•Semiconductor and IC Package Thermal Metrics (SPRA953)

11.2 Receiving Notification of Documentation Updates

To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper

right corner, click on Alert me to register and receive a weekly digest of any product information that has

changed. For change details, review the revision history included in any revised document.

11.3 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective

contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of

Use.

TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration

among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help

solve problems with fellow engineers.

Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and

contact information for technical support.

11.4 Trademarks

E2E is a trademark of Texas Instruments.

All other trademarks are the property of their respective owners.

11.5 Electrostatic Discharge Caution

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

12 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most

current data available for the designated devices. This data is subject to change without notice and revision of

this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

PACKAGE OPTION ADDENDUM

www.ti.com 13-Apr-2021

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead finish/

Ball material

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

LMV7219M5 ACTIVE SOT-23 DBV 5 1000 Non-RoHS

& Green Call TI Call TI -40 to 85 C14A

LMV7219M5/NOPB ACTIVE SOT-23 DBV 5 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 85 C14A

LMV7219M5X ACTIVE SOT-23 DBV 5 3000 Non-RoHS

& Green Call TI Call TI -40 to 85 C14A

LMV7219M5X/NOPB ACTIVE SOT-23 DBV 5 3000 RoHS & Green SN Level-1-260C-UNLIM -40 to 85 C14A

LMV7219M7 ACTIVE SC70 DCK 5 1000 Non-RoHS

& Green Call TI Call TI -40 to 85 C15

LMV7219M7/NOPB ACTIVE SC70 DCK 5 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 85 C15

LMV7219M7X/NOPB ACTIVE SC70 DCK 5 3000 RoHS & Green SN Level-1-260C-UNLIM -40 to 85 C15

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance

do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may

reference these types of products as "Pb-Free".

RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.

Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based

flame retardants must also meet the <=1000ppm threshold requirement.

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

PACKAGE OPTION ADDENDUM

www.ti.com 13-Apr-2021

Addendum-Page 2

(6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two

lines if the finish value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

LMV7219M5 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

LMV7219M5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

LMV7219M5X SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

LMV7219M5X/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

LMV7219M7 SC70 DCK 5 1000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3

LMV7219M7/NOPB SC70 DCK 5 1000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3

LMV7219M7X/NOPB SC70 DCK 5 3000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3

PACKAGE MATERIALS INFORMATION

www.ti.com 25-Sep-2019

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

LMV7219M5 SOT-23 DBV 5 1000 210.0 185.0 35.0

LMV7219M5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0

LMV7219M5X SOT-23 DBV 5 3000 210.0 185.0 35.0

LMV7219M5X/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0

LMV7219M7 SC70 DCK 5 1000 210.0 185.0 35.0

LMV7219M7/NOPB SC70 DCK 5 1000 210.0 185.0 35.0

LMV7219M7X/NOPB SC70 DCK 5 3000 210.0 185.0 35.0

PACKAGE MATERIALS INFORMATION

www.ti.com 25-Sep-2019

Pack Materials-Page 2

www.ti.com

PACKAGE OUTLINE

0.22

0.08 TYP

0.25

3.0

2.6

2X 0.95

1.9

1.45

0.90

0.15

0.00 TYP

5X 0.5

0.3

0.6

0.3 TYP

0 TYP

1.9

3.05

2.75

1.75

1.45

(1.1)

SOT-23 - 1.45 mm max heightDBV0005A

SMALL OUTLINE TRANSISTOR

4214839/E 09/2019

NOTES:

1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing

per ASME Y14.5M.

2. This drawing is subject to change without notice.

3. Refernce JEDEC MO-178.

4. Body dimensions do not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not

exceed 0.15 mm per side.

0.2 C A B

INDEX AREA

PIN 1

GAGE PLANE

SEATING PLANE

0.1 C

SCALE 4.000

www.ti.com

EXAMPLE BOARD LAYOUT

0.07 MAX

ARROUND 0.07 MIN

ARROUND

5X (1.1)

5X (0.6)

(2.6)

(1.9)

2X (0.95)

(R0.05) TYP

4214839/E 09/2019

SOT-23 - 1.45 mm max heightDBV0005A

SMALL OUTLINE TRANSISTOR

NOTES: (continued)

5. Publication IPC-7351 may have alternate designs.

6. Solder mask tolerances between and around signal pads can vary based on board fabrication site.

SYMM

LAND PATTERN EXAMPLE

EXPOSED METAL SHOWN

SCALE:15X

PKG

SOLDER MASK

OPENING

METAL UNDER

SOLDER MASK

DEFINED

EXPOSED METAL

METAL

SOLDER MASK

OPENING

NON SOLDER MASK

DEFINED

(PREFERRED)

SOLDER MASK DETAILS

EXPOSED METAL

www.ti.com

EXAMPLE STENCIL DESIGN

(2.6)

(1.9)

2X(0.95)

5X (1.1)

5X (0.6)

(R0.05) TYP

SOT-23 - 1.45 mm max heightDBV0005A

SMALL OUTLINE TRANSISTOR

4214839/E 09/2019

NOTES: (continued)

7. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate

design recommendations.

8. Board assembly site may have different recommendations for stencil design.

SOLDER PASTE EXAMPLE

BASED ON 0.125 mm THICK STENCIL

SCALE:15X

SYMM

PKG

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE

DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”

AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY

IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD

PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate

TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable

standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you

permission to use these resources only for development of an application that uses the TI products described in the resource. Other

reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party

intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages,

costs, losses, and liabilities arising out of your use of these resources.

TI’s products are provided subject to TI’s Terms of Sale (https:www.ti.com/legal/termsofsale.html) or other applicable terms available either

on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s

applicable warranties or warranty disclaimers for TI products.IMPORTANT NOTICE

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265