LNK362-364 LinkSwitch-XT Family (R) Energy Efficient, Low Power Off-Line Switcher IC Product Highlights Optimized for Lowest System Cost * Proprietary IC trimming and transformer construction techniques enable ClamplessTM designs with LNK362 for lower system cost, component count and higher efficiency * Fully integrated auto-restart for short circuit and open loop protection * Self-biased supply - saves transformer auxiliary winding and associated bias supply components * Frequency jittering greatly reduces EMI * Meets HV creepage requirements between DRAIN and all other pins both on the PCB and at the package * Lowest component count switcher solution Features Superior to Linear/RCC * Accurate hysteretic thermal shutdown protection - automatic recovery improves field reliability * Universal input range allows worldwide operation * Simple ON/OFF control, no loop compensation needed * Eliminates bias winding - simpler, lower cost transformer * Very low component count - higher reliability and single side printed circuit board * Auto-restart reduces delivered power by 95% during short circuit and open loop fault conditions * High bandwidth provides fast turn-on with no overshoot and excellent transient load response EcoSmart - Extremely Energy-Efficient * Easily meets all global energy efficiency regulations with no added components * No-load consumption <300 mW without bias winding at 265 VAC input (<50 mW with bias winding) * ON/OFF control provides constant efficiency to very light loads - ideal for mandatory CEC regulations (R) Applications * Chargers/adapters for cell/cordless phones, PDAs, digital cameras, MP3/portable audio players, and shavers * Supplies for appliances, industrial systems, and metering Description LinkSwitch-XT incorporates a 700 V power MOSFET, oscillator, simple ON/OFF control scheme, a high-voltage switched current source, frequency jittering, cycle-by-cycle current limit and thermal shutdown circuitry onto a monolithic IC. The startup + DC Output Wide Range HV DC Input + LinkSwitch-XT LNK362 D FB BP S a) Clampless flyback converter with LNK362 PI-4086-081005 + DC Output Wide Range HV DC Input + LinkSwitch-XT LNK363-364 D FB BP S b) Flyback converter with LNK363/4 PI-4061-081005 Figure 1. Typical Application with LinkSwitch-XT. OUTPUT POWER TABLE(4) 230 VAC 15% 85-265 VAC PRODUCT(3) Adapter(1) Open Open Adapter(1) Frame(2) Frame(2) LNK362P/G/D 2.8 W 2.8 W 2.6 W 2.6 W LNK363P/G/D 5W 7.5 W 3.7 W 4.7 W LNK364P/G/D 5.5 W 9W 4W 6W Table 1. Output Power Table. Notes: 1. Minimum continuous power in a typical non-ventilated enclosed adapter measured at 50 C ambient. 2. Minimum practical continuous power in an open frame design with adequate heat sinking, measured at 50 C ambient. 3. Packages: P: DIP-8B, G: SMD-8B, D: SO-8C. Please see Part Ordering Information. 4. See Key Application Considerations section for complete description of assumptions. and operating power are derived directly from the DRAIN pin, eliminating the need for a bias winding and associated circuitry. November 2008 LNK362-364 DRAIN (D) BYPASS (BP) REGULATOR 5.8 V FAULT PRESENT AUTORESTART COUNTER CLOCK RESET BYPASS PIN UNDER-VOLTAGE + 5.8 V 4.8 V - CURRENT LIMIT COMPARATOR 6.3 V + VI - LIMIT JITTER CLOCK DCMAX OSCILLATOR FEEDBACK (FB) THERMAL SHUTDOWN VFB -VTH S Q R Q LEADING EDGE BLANKING SOURCE (S) PI-4232-110205 Figure 2. Functional Block Diagram. Pin Functional Description DRAIN (D) Pin: Power MOSFET drain connection. Provides internal operating current for both startup and steady-state operation. BYPASS (BP) Pin: Connection point for a 0.1 F external bypass capacitor for the internally generated 5.8 V supply. If an external bias winding is used, the current into the BP pin must not exceed 1 mA. P Package (DIP-8B) G Package (SMD-8B) S 1 8 S S 2 7 S BP 3 FB FEEDBACK (FB) Pin: During normal operation, switching of the power MOSFET is controlled by this pin. MOSFET switching is disabled when a current greater than 49 A is delivered into this pin. SOURCE (S) Pin: This pin is the power MOSFET source connection. It is also the ground reference for the BYPASS and FEEDBACK pins. 2-2 22 Rev. E 11/08 5 4 3a D D Package (SO-8C) BP 1 8 S FB 2 7 S D 4 6 S 5 S 3b PI-3491-120706 Figure 3. Pin Configuration. LNK362-364 LinkSwitch-XT combines a high-voltage power MOSFET switch with a power supply controller in one device. Unlike conventional PWM (pulse width modulator) controllers, a simple ON/OFF control regulates the output voltage. The controller consists of an oscillator, feedback (sense and logic) circuit, 5.8 V regulator, BYPASS pin undervoltage circuit, over-temperature protection, frequency jittering, current limit circuit, and leading edge blanking integrated with a 700 V power MOSFET. The LinkSwitch-XT incorporates additional circuitry for auto-restart. Oscillator The typical oscillator frequency is internally set to an average of 132 kHz. Two signals are generated from the oscillator: the maximum duty cycle signal (DCMAX) and the clock signal that indicates the beginning of each cycle. The oscillator incorporates circuitry that introduces a small amount of frequency jitter, typically 9 kHz peak-to-peak, to minimize EMI emission. The modulation rate of the frequency jitter is set to 1.5 kHz to optimize EMI reduction for both average and quasi-peak emissions. The frequency jitter should be measured with the oscilloscope triggered at the falling edge of the DRAIN waveform. The waveform in Figure 4 illustrates the frequency jitter. Feedback Input Circuit The feedback input circuit at the FB pin consists of a low impedance source follower output set at 1.65 V for LNK362 and 1.63 V for LNK363/364. When the current delivered into this pin exceeds 49 A, a low logic level (disable) is generated at the output of the feedback circuit. This output is sampled at the beginning of each cycle on the rising edge of the clock signal. If high, the power MOSFET is turned on for that cycle (enabled), otherwise the power MOSFET remains off (disabled). Since the sampling is done only at the beginning of each cycle, subsequent changes in the FB pin voltage or current during the remainder of the cycle are ignored. pin through an external resistor. This facilitates powering of the device externally through a bias winding to decrease the no-load consumption to less than 50 mW. BYPASS Pin Undervoltage The BYPASS pin undervoltage circuitry disables the power MOSFET when the BYPASS pin voltage drops below 4.8 V. Once the BYPASS pin voltage drops below 4.8 V, it must rise back to 5.8 V to enable (turn-on) the power MOSFET. Over-Temperature Protection The thermal shutdown circuitry senses the die temperature. The threshold is set at 142 C typical with a 75 C hysteresis. When the die temperature rises above this threshold (142 C) the power MOSFET is disabled and remains disabled until the die temperature falls by 75 C, at which point it is re-enabled. Current Limit The current limit circuit senses the current in the power MOSFET. When this current exceeds the internal threshold (ILIMIT), the power MOSFET is turned off for the remainder of that cycle. The leading edge blanking circuit inhibits the current limit comparator for a short time (tLEB) after the power MOSFET is turned on. This leading edge blanking time has been set so that current spikes caused by capacitance and rectifier reverse recovery time will not cause premature termination of the switching pulse. Auto-Restart In the event of a fault condition such as output overload, output short circuit, or an open loop condition, LinkSwitch-XT enters into auto-restart operation. An internal counter clocked by the oscillator gets reset every time the FB pin is pulled high. If the FB pin is not pulled high for approximately 40 ms, the power MOSFET switching is disabled for 800 ms. The auto-restart alternately enables and disables the switching of the power MOSFET until the fault condition is removed. 600 500 PI-4047-110205 LinkSwitch-XT Functional Description V DRAIN 400 5.8 V Regulator and 6.3 V Shunt Voltage Clamp The 5.8 V regulator charges the bypass capacitor connected to the BYPASS pin to 5.8 V by drawing a current from the voltage on the DRAIN, whenever the MOSFET is off. The BYPASS pin is the internal supply voltage node. When the MOSFET is on, the LinkSwitch-XT runs off of the energy stored in the bypass capacitor. Extremely low power consumption of the internal circuitry allows the device to operate continuously from the current drawn from the DRAIN pin. A bypass capacitor value of 0.1 F is sufficient for both high frequency decoupling and energy storage. 300 200 100 0 136.5 kHz 127.5 kHz 0 In addition, there is a 6.3 V shunt regulator clamping the BYPASS pin at 6.3 V when current is provided to the BYPASS 5 10 Time (s) Figure 4. Frequency Jitter. 2-3 3 Rev. E 11/08 LNK362-364 CY1 100 pF 250 VAC L1 1 mH T1 EE16 9 4 5 J1 D2 1N4005 R1 3.9 k 1/8 W C1 3.3 F 400 V 85-265 VRMS R2 390 1/8 W D LinkSwitch-XT U1 LNK362P D4 1N4005 U2 PC817A FB R3 1k 1/8 W BP S L2 1 mH J4 VR1 BZX79B5V1 5.1 V, 2% C2 3.3 F 400 V J2 D3 1N4005 J3 8 NC NC D1 1N4005 6.2 V, 322 mA D5 1N4934 3 RF1 8.2 2.5 W C4 330 F 16 V C3 100 nF 50 V PI-4162-110205 Figure 5. 2 W Universal Input CV Adapter Using LNK362. Applications Example A 2 W CV Adapter The schematic shown in Figure 5 is a typical implementation of a universal input, 6.2 V 7%, 322 mA adapter using LNK362. This circuit makes use of the Clampless technique to eliminate the primary clamp components and reduce the cost and complexity of the circuit. The EcoSmart features built into the LinkSwitch-XT family allow this design to easily meet all current and proposed energy efficiency standards, including the mandatory California Energy Commission (CEC) requirement for average operating efficiency. The AC input is rectified by D1 to D4 and filtered by the bulk storage capacitors C1 and C2. Resistor RF1 is a flameproof, fusible, wire wound type and functions as a fuse, inrush current limiter and, together with the filter formed by C1, C2, L1 and L2, differential mode noise attenuator. Resistor R1 damps ringing caused by L1 and L2. This simple input stage, together with the frequency jittering of LinkSwitch-XT, a low value Y1 capacitor and PI's E-ShieldTM windings within T1, allow the design to meet both conducted and radiated EMI limits with >10 dBV margin. The low value of CY1 is important to meet the requirement for a very low touch current (the line frequency current that flows through CY1) often specified for adapters, in this case <10 A. 2-4 44 Rev. E 11/08 The rectified and filtered input voltage is applied to the primary winding of T1. The other side of the primary is driven by the integrated MOSFET in U1. No primary clamp is required as the low value and tight tolerance of the LNK362 internal current limit allows the transformer primary winding capacitance to provide adequate clamping of the leakage inductance drain voltage spike. The secondary of the flyback transformer T1 is rectified by D5, a low cost, fast recovery diode, and filtered by C4, a low ESR capacitor. The combined voltage drop across VR1, R2 and the LED of U2 determines the output voltage. When the output voltage exceeds this level, current will flow through the LED of U2. As the LED current increases, the current fed into the FEEDBACK pin of U1 increases until the turnoff threshold current (~49 A) is reached, disabling further switching cycles of U1. At full load, almost all switching cycles will be enabled, and at very light loads, almost all the switching cycles will be disabled, giving a low effective frequency and providing high light load efficiency and low no-load consumption. Resistor R3 provides 1 mA through VR1 to bias the Zener closer to its test current. Resistor R2 allows the output voltage to be adjusted to compensate for designs where the value of the Zener may not be ideal, as they are only available in discrete voltage ratings. For higher output accuracy, the Zener may be replaced with a reference IC such as the TL431. LNK362-364 The LinkSwitch-XT is completely self-powered from the DRAIN pin, requiring only a small ceramic capacitor C3 connected to the BYPASS pin. No auxiliary winding on the transformer is required. Key Application Considerations LinkSwitch-XT Design Considerations Output Power Table The data sheet maximum output power table (Table 1) represents the maximum practical continuous output power level that can be obtained under the following assumed conditions: 1. The minimum DC input voltage is 90 V or higher for 85 VAC input, or 240 V or higher for 230 VAC input or 115 VAC with a voltage doubler. The value of the input capacitance should be large enough to meet these criteria for AC input designs. 2. Secondary output of 6 V with a fast PN rectifier diode. 3. Assumed efficiency of 70%. 4. Voltage only output (no secondary-side constant current circuit). 5. Discontinuous mode operation (KP >1). 6. A primary clamp (RCD or Zener) is used. 7. The part is board mounted with SOURCE pins soldered to a sufficient area of copper to keep the SOURCE pin temperature at or below 100 C. 8. Ambient temperature of 50 C for open frame designs and an internal enclosure temperature of 60 C for adapter designs. Below a value of 1, KP is the ratio of ripple to peak primary current. Above a value of 1, KP is the ratio of primary MOSFET OFF time to the secondary diode conduction time. Due to the flux density requirements described below, typically a LinkSwitch-XT design will be discontinuous, which also has the benefits of allowing lower cost fast (instead of ultra-fast) output diodes and reducing EMI. Clampless Designs Clampless designs rely solely on the drain node capacitance to limit the leakage inductance induced peak drain-to-source voltage. Therefore, the maximum AC input line voltage, the value of VOR, the leakage inductance energy, a function of leakage inductance and peak primary current, and the primary winding capacitance determine the peak drain voltage. With no significant dissipative element present, as is the case with an external clamp, the longer duration of the leakage inductance ringing can increase EMI. The following requirements are recommended for a universal input or 230 VAC only Clampless design: 1. A Clampless design should only be used for PO 2.5 W, using the LNK362 and a VOR** 90 V. 2. For designs where PO 2 W, a two-layer primary should be used to ensure adequate primary intra-winding capacitance in the range of 25 pF to 50 pF. 3. For designs where 2 < PO 2.5 W, a bias winding should be added to the transformer using a standard recovery rectifier diode to act as a clamp. This bias winding may also be used to externally power the device by connecting a resistor from the bias-winding capacitor to the BYPASS pin. This inhibits the internal high-voltage current source, reducing device dissipation and no-load consumption. 4. For designs where PO > 2.5 W Clampless designs are not practical and an external RCD or Zener clamp should be used. 5. Ensure that worst-case high line, peak drain voltage is below the BVDSS specification of the internal MOSFET and ideally 650 V to allow margin for design variation. For 110 VAC only input designs it may be possible to extend the power range of Clampless designs to include the LNK363. However, the increased leakage ringing may degrade EMI performance. **VOR is the secondary output plus output diode forward voltage drop that is reflected to the primary via the turns ratio of the transformer during the diode conduction time. The VOR adds to the DC bus voltage and the leakage spike to determine the peak drain voltage. Audible Noise The cycle skipping mode of operation used in LinkSwitch-XT can generate audio frequency components in the transformer. To limit this audible noise generation, the transformer should be designed such that the peak core flux density is below 1500 Gauss (150 mT). Following this guideline and using the standard transformer production technique of dip varnishing practically eliminates audible noise. Vacuum impregnation of the transformer should not be used due to the high primary capacitance and increased losses that result. Higher flux densities are possible, however careful evaluation of the audible noise performance should be made using production transformer samples before approving the design. Ceramic capacitors that use dielectrics, such as Z5U, when used in clamp circuits may also generate audio noise. If this is the case, try replacing them with a capacitor having a different dielectric or construction, for example a film type. LinkSwitch-XT Layout Considerations See Figure 6 for a recommended circuit board layout for LinkSwitch-XT (P & G package). Single Point Grounding Use a single point ground connection from the input filter capacitor to the area of copper connected to the SOURCE pins. 2-5 5 Rev. E 11/08 LNK362-364 Input Filter Capacitor TOP VIEW Y1Capacitor FB T r a n s f o r m e r S LinkSwitch-XT D S BP S - HV DC + INPUT S S S CBP Optocoupler + DC OUT - Maximize hatched copper areas ( ) for optimum heatsinking Output Filter Capacitor PI-4155-102705 Figure 6. Recommended Printed Circuit Layout for LinkSwitch-XT using P Package in a Flyback Converter Configuration. Bypass Capacitor CBP The BYPASS pin capacitor should be located as near as possible to the BYPASS and SOURCE pins. Primary Loop Area The area of the primary loop that connects the input filter capacitor, transformer primary and LinkSwitch-XT together should be kept as small as possible. Primary Clamp Circuit A clamp is used to limit peak voltage on the DRAIN pin at turn-off. This can be achieved by using an RCD clamp or a Zener (~200 V) and diode clamp across the primary winding. In all cases, to minimize EMI, care should be taken to minimize the circuit path from the clamp components to the transformer and LinkSwitch-XT. Thermal Considerations The copper area underneath the LinkSwitch-XT acts not only as a single point ground, but also as a heatsink. As this area is connected to the quiet source node, it should be maximized for 2-6 66 Rev. E 11/08 good heat sinking of LinkSwitch-XT. The same applies to the cathode of the output diode. Y-Capacitor The placement of the Y-type cap should be directly from the primary input filter capacitor positive terminal to the common/ return terminal of the transformer secondary. Such a placement will route high magnitude common-mode surge currents away from the LinkSwitch-XT device. Note that if an input pi (C, L, C) EMI filter is used, then the inductor in the filter should be placed between the negative terminals of the input filter capacitors. Optocoupler Place the optocoupler physically close to the LinkSwitch-XT to minimize the primary-side trace lengths. Keep the high current, high-voltage drain and clamp traces away from the optocoupler to prevent noise pick up. Output Diode For best performance, the area of the loop connecting the secondary winding, the output diode and the output filter LNK362-364 TOP VIEW Y1Capacitor Input Filter Capacitor LinkSwitch-XT D T r a n s f o r m e r FB S S S S BP - + HV DC INPUT CBP Optocoupler Maximize hatched copper areas ( ) for optimum heatsinking Output Filter Capacitor + DC OUT PI-4585-021607 Figure 7. Recommended Printed Circuit Layout for LinkSwitch-XT using D Package in a Flyback Converter Configuration. capacitor should be minimized. In addition, sufficient copper area should be provided at the anode and cathode terminals of the diode for heat sinking. A larger area is preferred at the quiet cathode terminal. A large anode area can increase high frequency radiated EMI. Quick Design Checklist As with any power supply design, all LinkSwitch-XT designs should be verified on the bench to make sure that component specifications are not exceeded under worst-case conditions. The following minimum set of tests is strongly recommended: 1. Maximum drain voltage - Verify that VDS does not exceed 650 V at the highest input voltage and peak (overload) output power. The 50 V margin to the 700 V BVDSS specification gives margin for design variation, especially in Clampless designs. 2. Maximum drain current - At maximum ambient temperature, maximum input voltage and peak output (overload) power, verify drain current waveforms for any signs of transformer saturation and excessive leading-edge current spikes at startup. Repeat under steady state conditions and verify that the leadingedge current spike event is below ILIMIT(MIN) at the end of the tLEB(MIN). Under all conditions, the maximum drain current should be below the specified absolute maximum ratings. 3. Thermal Check - At specified maximum output power, minimum input voltage and maximum ambient temperature, verify that the temperature specifications are not exceeded for LinkSwitch-XT, transformer, output diode and output capacitors. Enough thermal margin should be allowed for part-to-part variation of the RDS(ON) of LinkSwitch-XT as specified in the data sheet. Under low line, maximum power, a maximum LinkSwitch-XT SOURCE pin temperature of 105 C is recommended to allow for these variations. Design Tools Up-to-date information on design tools can be found at the Power Integrations web site: www.powerint.com. 2-7 7 Rev. E 11/08 LNK362-364 ABSOLUTE MAXIMUM RATINGS(1,5) DRAIN Voltage .................................. .............-0.3 V to 700 V Peak DRAIN Current: LNK362................200 mA (375 mA)(2) LNK363/364.........400 mA (750 mA)(2) FEEDBACK Voltage ...........................................-0.3 V to 9 V FEEDBACK Current ...................................................100 mA BYPASS Voltage.................................................. -0.3 V to 9 V Storage Temperature .....................................-65 C to 150 C Operating Junction Temperature(3) ................-40 C to 150 C Lead Temperature(4) ....................................................... 260 C Notes: 1. All voltages referenced to SOURCE, TA = 25 C. 2. The higher peak DRAIN current is allowed while the DRAIN voltage is simultaneously less than 400 V. 3. Normally limited by internal circuitry. 4. 1/16 in. from case for 5 seconds. 5. Maximum ratings specified may be applied, one at a time, without causing permanent damage to the product. Exposure to Absolute Maximum Rating conditions for extended periods of time may affect product reliability. THERMAL IMPEDANCE Thermal Impedance: P or G Package: (JA) ........................... 70 C/W(3); 60 C/W(4) (JC)(1) ............................................... 11 C/W D Package: (JA) ..................... .... 100 C/W(3); 80 C/W(4) (JC)(2) ............................................... 30 C/W Notes: 1. Measured on pin 2 (SOURCE) close to plastic interface. 2. Measured on pin 8 (SOURCE) close to plastic interface. 3. Soldered to 0.36 sq. in. (232 mm2), 2 oz. (610 g/m2) copper clad. 4. Soldered to 1 sq. in. (645 mm2), 2 oz. (610 g/m2) copper clad. Conditions Parameter Symbol SOURCE = 0 V; TJ = -40 to 125 C See Figure 8 (Unless Otherwise Specified) Min Typ Max 124 132 9 140 Units CONTROL FUNCTIONS Output Frequency Maximum Duty Cycle FEEDBACK Pin Turnoff Threshold Current FEEDBACK Pin Voltage at Turnoff Threshold DRAIN Supply Current BYPASS Pin Charge Current BYPASS Pin Voltage BYPASS Pin Voltage Hysteresis 2-8 88 Rev. E 11/08 fOSC Average Peak-Peak Jitter TJ = 25 C DCMAX S2 Open 60 IFB TJ = 25 C 30 49 68 LNK362 1.55 1.65 1.75 LNK363-364 1.53 1.63 1.73 VFB TJ = 0 C to 125 C kHz % A V IS1 VFB 2 V (MOSFET Not Switching) See Note A 200 250 A IS2 FEEDBACK Open (MOSFET Switching) 250 300 A ICH1 VBP = 0 V, TJ = 25 C See Note C -5.5 -3.5 -1.8 ICH2 VBP = 4 V, TJ = 25 C See Note C -3.8 -2.3 -1.0 VBP 5.55 5.8 6.10 V VBPH 0.8 1.0 1.2 V mA LNK362-364 Conditions Parameter Symbol SOURCE = 0 V; TJ = -40 to 125 C See Figure 8 (Unless Otherwise Specified) Min Typ Max Units CONTROL FUNCTIONS (cont) BYPASS Pin Supply Current IBPSC See Note D A 68 CIRCUIT PROTECTION Current Limit Power Coefficient ILIMIT (See Note E) I2f Leading Edge Blanking Time tLEB Current Limit Delay tILD Thermal Shutdown Temperature TSD Thermal Shutdown Hysteresis TSHD di/dt = 30 mA/s TJ = 25 C LNK362 130 140 150 di/dt = 42 mA/s TJ = 25 C LNK363 195 210 225 di/dt = 50 mA/s TJ = 25 C LNK364 233 250 268 di/dt = 30 mA/s TJ = 25 C LNK362 2199 2587 di/dt = 42 mA/s TJ = 25 C LNK363 4948 5821 di/dt = 50 mA/s TJ = 25 C LNK364 7425 8250 LNK362 300 375 LNK363/364 170 250 TJ = 25 C See Note F TJ = 25 C See Note F See Note G A2Hz ns 125 135 142 mA ns 150 75 C C OUTPUT LNK362 ID = 14 mA ON-State Resistance RDS(ON) LNK363 ID = 21 mA LNK364 ID = 25 mA OFF-State Drain Leakage Current IDSS TJ = 25 C 48 55 TJ = 100 C 76 88 TJ = 25 C 29 33 TJ = 100 C 46 54 TJ = 25 C 24 28 TJ = 100 C 38 45 VBP = 6.2 V, VFB 2 V, VDS = 560 V, TJ = 125 C 50 A 2-9 9 Rev. E 11/08 LNK362-364 Conditions Parameter Symbol SOURCE = 0 V; TJ = -40 to 125 C See Figure 8 (Unless Otherwise Specified) Min Typ Max Units OUTPUT (cont) Breakdown Voltage VBP = 6.2 V, VFB 2 V, See Note H, TJ = 25 C BVDSS DRAIN Supply Voltage Output Enable Delay tEN Output Disable Setup Time tDST Auto-Restart ON-Time tAR Auto-Restart Duty Cycle 700 V 50 V See Figure 10 10 0.5 TJ = 25 C See Note I DCAR LNK362 40 LNK363-364 45 5 s s ms % NOTES: A. Total current consumption is the sum of IS1 and IDSS when FEEDBACK pin voltage is 2 V (MOSFET not switching) and the sum of IS2 and IDSS when FEEDBACK pin is shorted to SOURCE (MOSFET switching). B Since the output MOSFET is switching, it is difficult to isolate the switching current from the supply current at the DRAIN. An alternative is to measure the BYPASS pin current at 6 V. C. See Typical Performance Characteristics section Figure 15 for BYPASS pin startup charging waveform. D. This current is only intended to supply an optional optocoupler connected between the BYPASS and FEEDBACK pins and not any other external circuitry. E. For current limit at other di/dt values, refer to Figure 14. F. This parameter is guaranteed by design. G. This parameter is derived from characterization. H. Breakdown voltage may be checked against minimum BVDSS specification by ramping the DRAIN pin voltage up to but not exceeding minimum BVDSS. I. Auto-restart on time has the same temperature characteristics as the oscillator (inversely proportional to frequency). 2-10 10 10 Rev. E 11/08 LNK362-364 470 5W 470 k D S1 FB S2 BP 50 V S S S S 50 V 0.1 F PI-3490-060204 Figure 8. LinkSwitch-XT General Test Circuit. DCMAX t2 (internal signal) t1 tP HV 90% 90% FB DRAIN VOLTAGE t D= 1 t2 VDRAIN tEN 10% 0V tP = 1 fOSC PI-3707-112503 PI-2048-033001 Figure 9. LinkSwitch-XT Duty Cycle Measurement. Figure 10. LinkSwitch-XT Output Enable Timing. 2-11 11 Rev. E 11/08 LNK362-364 Typical Performance Characteristics 1.0 PI-2680-012301 1.2 Output Frequency (Normalized to 25 C) PI-2213-012301 1.0 0.8 0.6 0.4 0.2 0 0.9 -50 -25 0 25 50 -50 75 100 125 150 -25 Junction Temperature (C) 1.0 0.8 0.6 0.4 0.2 50 100 100 125 PI-4092-081505 1.2 1.0 0.8 Normalized di/dt = 1 TBD LNK362 30 mA/s LNK363 42 mA/s LNK364 50 mA/s 0.6 0.4 Normalized Current Limit = 1 140 mA 210 mA 250 mA 0.2 150 Temperature (C) Figure 13. Current Limit vs. Temperature. 6 1 2 3 4 5 Normalized di/dt Figure 14. Current Limit vs. di/dt. PI-2240-012301 7 BYPASS Pin Voltage (V) 75 0 0 5 4 3 2 1 400 350 DRAIN Current (mA) 0 -50 50 1.4 Normalized Current Limit PI-4091-081505 Current Limit (Normalized to 25 C) 1.2 25 Figure 12. Frequency vs. Temperature. Figure 11. Breakdown vs. Temperature. 1.4 0 Junction Temperature (C) PI-4093-081605 Breakdown Voltage (Normalized to 25 C) 1.1 25 C 300 100 C 250 200 Scaling Factors: LNK362 0.5 LNK363 0.8 LNK364 1.0 150 100 50 0 0 0 0.2 0.4 0.6 0.8 Time (ms) Figure 15. BYPASS Pin Startup Waveform. 2-12 12 12 Rev. E 11/08 1.0 0 2 4 6 8 10 12 14 16 18 20 DRAIN Voltage (V) Figure 16. Output Characteristics. LNK362-364 Typical Performance Characteristics (cont.) PI-4094-081605 Drain Capacitance (pF) 1000 100 Scaling Factors: LNK362 0.5 LNK363 0.8 LNK364 1.0 10 1 0 100 200 300 400 500 600 Drain Voltage (V) Figure 17. COSS vs. Drain Voltage. PART ORDERING INFORMATION LinkSwitch Product Family XT Series Number Package Identifier G Plastic Surface Mount DIP P Plastic DIP D Plastic SO-8 Lead Finish N Pure Matte Tin (RoHS Compliant) G RoHS Compliant and Halogen Free (P and D package only) Tape & Reel and Other Options Blank Standard Configurations LNK 364 G N - TL TL Tape & Reel, 1 k pcs minimum for G Package. 2.5 k pcs for D Package. Not available for P Package. 2-13 13 Rev. E 11/08 LNK362-364 DIP-8B D S .004 (.10) -E- Notes: 1. Package dimensions conform to JEDEC specification MS-001-AB (Issue B 7/85) for standard dual-in-line (DIP) package with .300 inch row spacing. 2. Controlling dimensions are inches. Millimeter sizes are shown in parentheses. 3. Dimensions shown do not include mold flash or other protrusions. Mold flash or protrusions shall not exceed .006 (.15) on any side. 4. Pin locations start with Pin 1, and continue counter-clockwise to Pin 8 when viewed from the top. The notch and/or dimple are aids in locating Pin 1. Pin 6 is omitted. 5. Minimum metal to metal spacing at the package body for the omitted lead location is .137 inch (3.48 mm). 6. Lead width measured at package body. 7. Lead spacing measured with the leads constrained to be perpendicular to plane T. .137 (3.48) MINIMUM .240 (6.10) .260 (6.60) Pin 1 -D- .367 (9.32) .387 (9.83) .125 (3.18) .145 (3.68) .057 (1.45) .068 (1.73) (NOTE 6) .015 (.38) MINIMUM -TSEATING PLANE .100 (2.54) BSC .008 (.20) .015 (.38) .120 (3.05) .140 (3.56) .300 (7.62) BSC (NOTE 7) .300 (7.62) .390 (9.91) .048 (1.22) .053 (1.35) .014 (.36) .022 (.56) T E D S .010 (.25) M P08B PI-2551-121504 SMD-8B D S .004 (.10) .137 (3.48) MINIMUM -E- .372 (9.45) .388 (9.86) E S .010 (.25) .240 (6.10) .260 (6.60) Pin 1 .100 (2.54) (BSC) -D- .367 (9.32) .387 (9.83) .057 (1.45) .068 (1.73) (NOTE 5) .125 (3.18) .145 (3.68) .032 (.81) .037 (.94) .048 (1.22) .053 (1.35) Notes: 1. Controlling dimensions are inches. Millimeter sizes are shown in parentheses. 2. Dimensions shown do not include mold flash or other protrusions. Mold flash or protrusions shall not exceed .006 (.15) on any side. .420 3. Pin locations start with Pin 1, and continue counter-clock.046 .060 .060 .046 wise to Pin 8 when viewed from the top. Pin 6 is omitted. 4. Minimum metal to metal .080 spacing at the package body Pin 1 for the omitted lead location is .137 inch (3.48 mm). .086 5. Lead width measured at .186 package body. .286 6. D and E are referenced Solder Pad Dimensions datums on the package body. .004 (.10) .009 (.23) .004 (.10) .012 (.30) .036 (0.91) .044 (1.12) 0- 8 G08B PI-2546-121504 2-14 14 14 Rev. E 11/08 LNK362-364 SO-8C 4 B 0.10 (0.004) C A-B 2X 2 DETAIL A 4.90 (0.193) BSC A 4 8 D 5 GAUGE PLANE 2 3.90 (0.154) BSC SEATING PLANE 6.00 (0.236) BSC 0-8 C 1.04 (0.041) REF 0.10 (0.004) C D 2X Pin 1 ID 1 4 0.25 (0.010) BSC 0.40 (0.016) 1.27 (0.050) 0.20 (0.008) C 2X 7X 0.31 - 0.51 (0.012 - 0.020) 0.25 (0.010) M C A-B D 1.27 (0.050) BSC 1.25 - 1.65 (0.049 - 0.065) 1.35 (0.053) 1.75 (0.069) o DETAIL A 0.10 (0.004) 0.25 (0.010) 0.10 (0.004) C H 7X SEATING PLANE 0.17 (0.007) 0.25 (0.010) C Reference Solder Pad Dimensions + 2.00 (0.079) + D07C 4.90 (0.193) + 1.27 (0.050) + Notes: 1. JEDEC reference: MS-012. 2. Package outline exclusive of mold flash and metal burr. 3. Package outline inclusive of plating thickness. 4. Datums A and B to be determined at datum plane H. 5. Controlling dimensions are in millimeters. Inch dimensions are shown in parenthesis. Angles in degrees. 0.60 (0.024) PI-4526-040207 Revision Notes Date B 1) Released Final Data Sheet. 11/05 C 1) Corrected Application Example section. 12/05 D 1) Added SO-8C package. 2/07 E 1) Updated Part Ordering Information section with Halogen Free 11/08 2-15 15 Rev. E 11/08 LNK362-364 For the latest updates, visit our website: www.powerint.com Power Integrations reserves the right to make changes to its products at any time to improve reliability or manufacturability. Power Integrations does not assume any liability arising from the use of any device or circuit described herein. POWER INTEGRATIONS MAKES NO WARRANTY HEREIN AND SPECIFICALLY DISCLAIMS ALL WARRANTIES INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS. Patent Information The products and applications illustrated herein (including transformer construction and circuits external to the products) may be covered by one or more U.S. and foreign patents, or potentially by pending U.S. and foreign patent applications assigned to Power Integrations. A complete list of Power Integrations patents may be found at www.powerint.com. Power Integrations grants its customers a license under certain patent rights as set forth at http://www.powerint.com/ip.htm. Life Support Policy POWER INTEGRATIONS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF POWER INTEGRATIONS. As used herein: 1. A Life support device or system is one which, (i) is intended for surgical implant into the body, or (ii) supports or sustains life, and (iii) whose failure to perform, when properly used in accordance with instructions for use, can be reasonably expected to result in significant injury or death to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. The PI logo, TOPSwitch, TinySwitch, LinkSwitch, DPA-Switch, PeakSwitch, EcoSmart, Clampless, E-Shield, Filterfuse, StakFET, PI Expert and PI FACTS are trademarks of Power Integrations, Inc. Other trademarks are property of their respective companies. (c)2007, Power Integrations, Inc. Power Integrations Worldwide Sales Support Locations World Headquarters 5245 Hellyer Avenue San Jose, CA 95138, USA. Main: +1-408-414-9200 Customer Service: Phone: +1-408-414-9665 Fax: +1-408-414-9765 e-mail: usasales@powerint.com China (Shanghai) Room 1601/1610, Tower 1 Kerry Everbright City No. 218 Tianmu Road West Shanghai, P.R.C. 200070 Phone: +86-21-6354-6323 Fax: +86-21-6354-6325 e-mail: chinasales@powerint.com China (Shenzhen) Rm A, B & C 4th Floor, Block C, Electronics Science and Technology Bldg., 2070 Shennan Zhong Rd, Shenzhen, Guangdong, China, 518031 Phone: +86-755-8379-3243 Fax: +86-755-8379-5828 e-mail: chinasales@powerint.com 2-16 16 16 Rev. E 11/08 Germany Rueckertstrasse 3 D-80336, Munich Germany Phone: +49-89-5527-3910 Fax: +49-89-5527-3920 e-mail: eurosales@powerint.com India #1, 14th Main Road Vasanthanagar Bangalore-560052 India Phone: +91-80-4113-8020 Fax: +91-80-4113-8023 e-mail: indiasales@powerint.com Italy Via De Amicis 2 20091 Bresso MI Italy Phone: +39-028-928-6000 Fax: +39-028-928-6009 e-mail: eurosales@powerint.com Japan Kosei Dai-3 Bldg. 2-12-11, Shin-Yokomana, Kohoku-ku Yokohama-shi Kanagwan 222-0033 Japan Phone: +81-45-471-1021 Fax: +81-45-471-3717 e-mail: japansales@powerint.com Korea RM 602, 6FL Korea City Air Terminal B/D, 159-6 Samsung-Dong, Kangnam-Gu, Seoul, 135-728, Korea Phone: +82-2-2016-6610 Fax: +82-2-2016-6630 e-mail: koreasales@powerint.com Taiwan 5F, No. 318, Nei Hu Rd., Sec. 1 Nei Hu Dist. Taipei, Taiwan 114, R.O.C. Phone: +886-2-2659-4570 Fax: +886-2-2659-4550 e-mail: taiwansales@powerint.com Europe HQ 1st Floor, St. James's House East Street, Farnham Surrey GU9 7TJ United Kingdom Phone: +44 (0) 1252-730-141 Fax: +44 (0) 1252-727-689 e-mail: eurosales@powerint.com Applications Hotline World Wide +1-408-414-9660 Singapore Applications Fax 51 Newton Road World Wide +1-408-414-9760 #15-08/10 Goldhill Plaza Singapore, 308900 Phone: +65-6358-2160 Fax: +65-6358-2015 e-mail: singaporesales@powerint.com