P6KE6.8 thru P6KE540A Vishay General Semiconductor TRANSZORB(R) Transient Voltage Suppressors FEATURES * Glass passivated chip junction * Available in uni-directional and bi-directional * 600 W peak pulse power capability with a 10/1000 s waveform, repetitive rate (duty cycle): 0.01 % * Excellent clamping capability * Very fast response time * Low incremental surge resistance * Solder dip 260 C, 40 s * Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC DO-204AC (DO-15) PRIMARY CHARACTERISTICS VBR uni-directional 6.8 V to 540 V VBR bi-directional 6.8 V to 440 V PPPM 600 W PD 5.0 W IFSM (uni-directional only) 100 A TJ max. 175 C DEVICES FOR BI-DIRECTION APPLICATIONS For bi-directional types, use C or CA suffix (e.g. P6KE440CA). Electrical characteristics apply in both directions. TYPICAL APPLICATIONS Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, automotive and telecommunication. MECHANICAL DATA Case: DO-204AC, molded epoxy over passivated chip Molding compound meets UL 94 V-0 flammability rating Base P/N-E3 - RoHS compliant, commercial grade Base P/NHE3 - RoHS compliant, high reliability/ automotive grade (AEC Q101 qualified) Terminals: Matte tin plated leads, solderable per J-STD-002 and JESD22-B102 E3 suffix meets JESD 201 class 1A whisker test, HE3 suffix meets JESD 201 class 2 whisker test Note: * P6KE250 ~ P6KE540A and P6KE250C ~ P6KE440CA for commercial grade only Polarity: For uni-directional types the color band denotes cathode end, no marking on bi-directional types MAXIMUM RATINGS (TA = 25 C unless otherwise noted) PARAMETER Peak power dissipation with a 10/1000 s waveform (1) (Fig. 1) Peak pulse current with a 10/1000 s waveform (1) SYMBOL VALUE UNIT PPPM 600 W IPPM See next table A Power dissipation on infinite heatsink at TL = 75 C (Fig. 5) PD 5.0 W Peak forward surge current, 8.3 ms single half sine-wave (2) IFSM 100 A Maximum instantaneous forward voltage at 50 A for uni-directional only Operating junction and storage temperature range (3) VF 3.5/5.0 V TJ, TSTG - 55 to + 175 C Notes: (1) Non-repetitive current pulse, per Fig. 3 and derated above TA = 25 C per Fig. 2 (2) Measured on 8.3 ms single half sine-wave or equivalent square wave, duty cycle = 4 per minute maximum (3) VF = 3.5 V for P6KE220(A) and below; VF = 5.0 V for P6KE250(A) and above Document Number: 88369 Revision: 22-Oct-08 For technical questions within your region, please contact one of the following: PDD-Americas@vishay.com, PDD-Asia@vishay.com, PDD-Europe@vishay.com www.vishay.com 1 P6KE6.8 thru P6KE540A Vishay General Semiconductor ELECTRICAL CHARACTERISTICS (TA = 25 C unless otherwise noted) BREAKDOWN VOLTAGE DEVICE TYPE (+)P6KE6.8 VBR AT IT (1) (V) MIN. MAX. 6.12 7.48 MAXIMUM REVERSE LEAKAGE TEST CURRENT IT (mA) STAND-OFF VOLTAGE VWM (V) 10 5.50 1000 AT VWM (3) ID (A) PEAK MAXIMUM PULSE CLAMPING CURRENT VOLTAGE AT IPPM VC (V) IPPM (2) (A) 55.6 10.8 MAXIMUM TEMPERATURE COEFFICIENT OF VBR (%/C) 0.057 (+) 6.45 7.14 10 5.80 1000 57.1 10.5 0.057 (+)P6KE7.5 6.75 8.25 10 6.05 500 51.3 11.7 0.061 P6KE6.8A (+)P6KE7.5A 7.13 7.88 10 6.40 500 53.1 11.3 0.061 (+) 7.38 9.02 10 6.63 200 48.0 12.5 0.065 P6KE8.2 (+)P6KE8.2A 7.79 8.61 10 7.02 200 49.6 12.1 0.065 (+) 8.19 10.0 1.0 7.37 50 43.5 13.8 0.068 (+) 8.65 9.55 1.0 7.78 50 44.8 13.4 0.068 P6KE9.1 P6KE9.1A (+)P6KE10 9.00 11.0 1.0 8.10 10 40.0 15.0 0.073 (+) 9.50 10.5 1.0 8.55 10 41.4 14.5 0.073 (+) P6KE11 9.90 12.1 1.0 8.92 5.0 37.0 16.2 0.075 (+)P6KE11A 10.5 11.6 1.0 9.40 5.0 38.5 15.6 0.075 (+)P6KE12 10.8 13.2 1.0 9.72 5.0 34.7 17.3 0.078 (+) 11.4 12.6 1.0 10.2 5.0 35.9 16.7 0.078 (+)P6KE13 11.7 14.3 1.0 10.5 5.0 31.6 19.0 0.081 (+)P6KE13A 12.4 13.7 1.0 11.1 5.0 33.0 18.2 0.081 (+) P6KE15 13.5 16.5 1.0 12.1 1.0 27.3 22.0 0.084 (+)P6KE15A 14.3 15.8 1.0 12.8 1.0 28.3 21.2 0.084 (+)P6KE16 14.4 17.6 1.0 12.9 1.0 25.5 23.5 0.086 (+) 15.2 16.8 1.0 13.6 1.0 26.7 22.5 0.086 (+) P6KE18 16.2 19.8 1.0 14.5 1.0 22.6 26.5 0.088 (+)P6KE18A 17.1 18.9 1.0 15.3 1.0 23.8 25.2 0.088 (+) P6KE20 18.0 22.0 1.0 16.2 1.0 20.6 29.1 0.090 (+)P6KE20A 19.0 21.0 1.0 17.1 1.0 21.7 27.7 0.090 (+)P6KE22 19.8 24.2 1.0 17.8 1.0 18.8 31.9 0.092 (+) 20.9 23.1 1.0 18.8 1.0 19.6 30.6 0.092 (+)P6KE24 21.6 26.4 1.0 19.4 1.0 17.3 34.7 0.094 (+)P6KE24A 22.8 25.2 1.0 20.5 1.0 18.1 33.2 0.094 (+) P6KE27 24.3 29.7 1.0 21.8 1.0 15.3 39.1 0.096 (+)P6KE27A 25.7 28.4 1.0 23.1 1.0 16.0 37.5 0.096 (+) 27.0 33.0 1.0 24.3 1.0 13.8 43.5 0.097 P6KE10A P6KE12A P6KE16A P6KE22A P6KE30 (+) 28.5 31.5 1.0 25.6 1.0 14.5 41.4 0.097 (+)P6KE33 29.7 36.3 1.0 26.8 1.0 12.6 47.7 0.098 P6KE30A (+)P6KE33A 31.4 34.7 1.0 28.2 1.0 13.1 45.7 0.098 (+) 32.4 39.6 1.0 29.1 1.0 11.5 52.0 0.099 P6KE36 (+) 34.2 37.8 1.0 30.8 1.0 12.0 49.9 0.099 (+)P6KE39 35.1 42.9 1.0 31.6 1.0 10.6 56.4 0.100 (+) 37.1 41.0 1.0 33.3 1.0 11.1 53.9 0.100 (+)P6KE43 38.7 47.3 1.0 34.8 1.0 9.7 61.9 0.101 (+) 40.9 45.2 1.0 36.8 1.0 10.1 59.3 0.101 (+) P6KE47 42.3 51.7 1.0 38.1 1.0 8.8 67.8 0.101 (+)P6KE47A 44.7 49.4 1.0 40.2 1.0 9.3 64.8 0.101 P6KE36A P6KE39A P6KE43A www.vishay.com 2 For technical questions within your region, please contact one of the following: PDD-Americas@vishay.com, PDD-Asia@vishay.com, PDD-Europe@vishay.com Document Number: 88369 Revision: 22-Oct-08 P6KE6.8 thru P6KE540A Vishay General Semiconductor ELECTRICAL CHARACTERISTICS (TA = 25 C unless otherwise noted) BREAKDOWN VOLTAGE DEVICE TYPE VBR AT IT (V) MIN. (1) MAX. TEST CURRENT IT (mA) STAND-OFF VOLTAGE VWM (V) MAXIMUM REVERSE LEAKAGE AT VWM (3) ID (A) PEAK MAXIMUM PULSE CLAMPING CURRENT VOLTAGE AT IPPM VC (V) IPPM (2) (A) MAXIMUM TEMPERATURE COEFFICIENT OF VBR (%/C) (+)P6KE51 45.9 56.1 1.0 41.3 1.0 8.2 73.5 0.102 (+)P6KE51A 48.5 53.6 1.0 43.6 1.0 8.6 70.1 0.102 (+) P6KE56 50.4 61.6 1.0 45.4 1.0 7.5 80.5 0.103 (+)P6KE56A 53.2 58.8 1.0 47.8 1.0 7.8 77.0 0.103 (+)P6KE62 55.8 68.2 1.0 50.2 1.0 6.7 89.0 0.104 (+) 58.9 65.1 1.0 53.0 1.0 7.1 85.0 0.104 (+) 61.2 74.8 1.0 55.1 1.0 6.1 98.0 0.104 (+) 64.6 71.4 1.0 58.1 1.0 6.5 92.0 0.104 (+) P6KE75 67.5 82.5 1.0 60.7 1.0 5.6 108 0.105 (+)P6KE75A 71.3 78.8 1.0 64.1 1.0 5.8 103 0.105 P6KE62A P6KE68 P6KE68A (+)P6KE82 73.8 90.2 1.0 66.4 1.0 5.1 118 0.105 (+) 77.9 86.1 1.0 70.1 1.0 5.3 113 0.105 P6KE82A (+)P6KE91 81.9 100 1.0 73.7 1.0 4.6 131 0.106 (+)P6KE91A 86.5 95.5 1.0 77.8 1.0 4.8 125 0.106 (+) P6KE100 90.0 110 1.0 81.0 1.0 4.2 144 0.106 (+)P6KE100A 95.0 105 1.0 85.5 1.0 4.4 137 0.106 (+)P6KE110 99.0 121 1.0 89.2 1.0 3.8 158 0.107 (+) 105 116 1.0 94.0 1.0 3.9 152 0.107 P6KE110A (+)P6KE120 108 132 1.0 97.2 1.0 3.5 173 0.107 (+)P6KE120A 114 126 1.0 102 1.0 3.6 165 0.107 (+) 117 143 1.0 105 1.0 3.2 187 0.107 (+) 124 137 1.0 111 1.0 3.4 179 0.107 P6KE130 P6KE130A (+)P6KE150 135 165 1.0 121 1.0 2.8 215 0.108 (+) 143 158 1.0 128 1.0 2.9 207 0.108 P6KE150A (+)P6KE160 144 176 1.0 130 1.0 2.6 230 0.108 (+)P6KE160A 152 168 1.0 136 1.0 2.7 219 0.108 (+) P6KE170 153 187 1.0 138 1.0 2.5 244 0.108 (+)P6KE170A 162 179 1.0 145 1.0 2.6 234 0.108 (+) 162 198 1.0 146 1.0 2.3 258 0.108 (+) 171 189 1.0 154 1.0 2.4 246 0.108 P6KE180 P6KE180A (+)P6KE200 180 220 1.0 162 1.0 2.1 287 0.108 (+)P6KE200A 190 210 1.0 171 1.0 2.2 274 0.108 (+) 198 242 1.0 175 1.0 1.7 344 0.108 (+) 209 231 1.0 185 1.0 1.8 328 0.108 (+) 225 275 1.0 202 1.0 1.7 360 0.110 (+) 237 263 1.0 214 1.0 1.7 344 0.110 (+)P6KE300 270 330 1.0 243 1.0 1.4 430 0.110 (+) 285 315 1.0 256 1.0 1.4 414 0.110 (+) P6KE350 315 385 1.0 284 1.0 1.2 504 0.110 (+)P6KE350A 333 368 1.0 300 1.0 1.2 482 0.110 (+)P6KE400 360 440 1.0 324 1.0 1.0 574 0.110 (+) 380 420 1.0 342 1.0 1.1 548 0.110 P6KE220 P6KE220A P6KE250 P6KE250A P6KE300A P6KE400A Document Number: 88369 Revision: 22-Oct-08 For technical questions within your region, please contact one of the following: PDD-Americas@vishay.com, PDD-Asia@vishay.com, PDD-Europe@vishay.com www.vishay.com 3 P6KE6.8 thru P6KE540A Vishay General Semiconductor ELECTRICAL CHARACTERISTICS (TA = 25 C unless otherwise noted) BREAKDOWN VOLTAGE VBR AT IT (V) DEVICE TYPE (1) TEST CURRENT IT (mA) STAND-OFF VOLTAGE VWM (V) MAXIMUM REVERSE LEAKAGE AT VWM (3) ID (A) PEAK MAXIMUM PULSE CLAMPING CURRENT VOLTAGE AT IPPM VC (V) IPPM (2) (A) MAXIMUM TEMPERATURE COEFFICIENT OF VBR (%/C) MIN. MAX. (+)P6KE440 396 484 1.0 356 1.0 0.95 631 0.110 (+)P6KE440A 418 462 1.0 376 1.0 1.00 602 0.110 P6KE480 432 528 1.0 389 1.0 0.88 686 0.110 P6KE480A 456 504 1.0 408 1.0 0.91 658 0.110 P6KE510 459 561 1.0 413 1.0 0.82 729 0.110 P6KE510A 485 535 1.0 434 1.0 0.86 698 0.110 P6KE540 486 594 1.0 437 1.0 0.78 772 0.110 P6KE540A 513 567 1.0 459 1.0 0.81 740 0.110 Notes: (1) Pulse test: tp 50 ms (2) Surge current waveform per Fig. 3 and derate per Fig. 2ogm (3) For bi-directional types with VWM of 10 V and less, the ID limit is doubled (4) All terms and symbols are consistent with ANSI/IEEE C62.35 (+) Underwriters laboratory recognition for the classification of protectors (QVGQ2) under the UL standard for safety 497B and file number E136766 for both uni-directional and bi-directional devices THERMAL CHARACTERISTICS (TA = 25 C unless otherwise noted) PARAMETER SYMBOL VALUE UNIT Typical thermal resistance, junction to lead RJL 20 C/W Typical thermal resistance, junction to ambient RJA 75 C/W ORDERING INFORMATION (Example) PREFERRED P/N UNIT WEIGHT (g) PREFERRED PACKAGE CODE BASE QUANTITY DELIVERY MODE P6KE6.8A-E3/54 0.432 54 4000 13" diameter paper tape and reel P6KE6.8AHE3/54 (1) 0.432 54 4000 13" diameter paper tape and reel Note: (1) Automotive grade AEC-Q101 qualified www.vishay.com 4 For technical questions within your region, please contact one of the following: PDD-Americas@vishay.com, PDD-Asia@vishay.com, PDD-Europe@vishay.com Document Number: 88369 Revision: 22-Oct-08 P6KE6.8 thru P6KE540A Vishay General Semiconductor RATINGS AND CHARACTERISTICS CURVES (TA = 25 C unless otherwise noted) 6000 Non-Repetitive Pulse Waveform shown in Fig. 3 TA = 25 C 10 1 Measured at Zero Bias 1000 TJ = 25 C f = 1.0 MHz Vsig = 50 mVp-p 100 Measured at Stand-Off Voltage VWM 10 0.1 0.1 s 1.0 s 100 s 10 s 1.0 ms 10 ms 1.0 10 100 VBR - Breakdown Voltage (V) Figure 1. Peak Pulse Power Rating Curve Figure 4. Typical Junction Capacitance Uni-Directional 6 100 75 50 25 60 Hz Resistive or Inductive Load 5 4 3 L = 0.375" (9.5 mm) Lead Lengths 2 1 0 0 0 25 50 75 100 125 150 175 0 200 25 50 75 100 125 150 175 TJ - Initial Temperature (C) TL - Lead Temperature (C) Figure 2. Pulse Power or Current vs. Initial Junction Temperature Figure 5. Power Derating Curve 150 Peak Value IPPM 100 Half Value - IPP IPPM 2 50 200 200 TJ = 25 C Pulse Width (td) is defined as the Point where the Peak Current decays to 50 % of IPPM tr = 10 s IFSM - Peak Forward Surge Current (A) IPPM - Peak Pulse Current, % IRSM 200 td - Pulse Width (s) PD - Power Dissipation (W) Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage, % CJ - Junction Capacitance (pF) PPPM - Peak Pulse Power (kW) 100 10/1000 s Waveform as defined by R.E.A. td TJ = TJ max. 8.3 ms Single Half Sine-Wave 100 50 Uni-Directional Only 10 0 0 1.0 2.0 3.0 4.0 1 5 10 50 100 t - Time (ms) Number of Cycles at 60 Hz Figure 3. Pulse Waveform Figure 6. Maximum Non-Repetitive Forward Surge Current Document Number: 88369 Revision: 22-Oct-08 For technical questions within your region, please contact one of the following: PDD-Americas@vishay.com, PDD-Asia@vishay.com, PDD-Europe@vishay.com www.vishay.com 5 P6KE6.8 thru P6KE540A Vishay General Semiconductor Transient Thermal Impedance (C/W) 100 10 1 0.1 0.001 0.01 0.1 1 10 100 1000 tp - Pulse Duration (s) Figure 7. Typical Transient Thermal Impedance PACKAGE OUTLINE DIMENSIONS in inches (millimeters) DO-204AC (DO-15) 0.034 (0.86) 0.028 (0.71) DIA. 1.0 (25.4) MIN. 0.300 (7.6) 0.230 (5.8) 0.140 (3.6) 0.104 (2.6) DIA. 1.0 (25.4) MIN. APPLICATION NOTE This P6KE TVS series is a low cost commercial product for use in applications where large voltage transients can permanently damage voltage-sensitive components. The P6KE series device types are designed in a small package size where power and space is a consideration. They are characterized by their high surge capability, extremely fast response time, and low impedance, (Ron). Because of the unpredictable nature of transients, and the variation of the impedance with respect to these transients, impedance, per se, is not specified as a parametric value. However, a minimum voltage at low current conditions (BV) and a maximum clamping voltage (Vc) at a maximum peak pulse current is specified. www.vishay.com 6 In some instances, the thermal effect (see Vc Clamping Voltage) may be responsible for 50 % to 70 %. of the observed voltage differential when subjected to high current pulses for several duty cycles, thus making a maximum impedance specification insignificant. In case of a severe current overload or abnormal transient beyond the maximum ratings, the Transient Voltage Suppressor will initially fail 'short' thus tripping the system's circuit breaker or fuse while protecting the entire circuit. Curves depicting clamping voltage vs. various current pulses are available from the factory. Extended power curves vs. pulse time are also available. For technical questions within your region, please contact one of the following: PDD-Americas@vishay.com, PDD-Asia@vishay.com, PDD-Europe@vishay.com Document Number: 88369 Revision: 22-Oct-08 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Revision: 12-Mar-12 1 Document Number: 91000 Packaging Information www.vishay.com Vishay General Semiconductor Packaging Information PACKAGING ORDERING CODE PREFERRED ANTI-STATIC PACKAGE CODE PACKAGE CODE 51 52, 52T P 2D P 2E 2M 2N 53 54 P 5A, 5AT P 5B, 5BT P 5CA P 57, 57T P 6A P 6B P 9A, 9AT P 61, 61T P 67A P 72 P 73 77 P 80 P 81 P 8A P 8W P 83 P 84A P 85A P 86A P 87A P 38 89A P 90 91 92 93 45 P 4W P 96 P 97 P 98 P 100 Bulk DO-214AA (SMB)/DO-215AA (SMBG), 12 mm tape, 7" diameter plastic reel DO-218AB (SM5-8A), 24 mm tape, 13" diameter plastic reel, anode towards sprocket hole DO-218AB (SM5-8A), 24 mm tape, 13" diameter plastic reel, cathode towards sprocket hole Tube packaging for 5KP/6KA type lead formed components DO-218AB, 24 mm tape, 13 "diameter plastic reel with dry packaging, anode towards sprocket hole 26 mm horizontal taping and ammo box packaging 52.4 mm horizontal tape, 13" diameter paper reel DO-214AC (SMA), 12 mm tape, 13" diameter plastic reel DO-214AA (SMB)/DO-215AA (SMBG), 12 mm tape, 13" diameter plastic reel DO-214BA (GF1), 12 mm tape, 13" diameter plastic reel DO-214AB (SMC)/DO-215AB (SMCG), 16 mm tape, 7" diameter plastic reel DO-221AC (SlimSMA), 12 mm tape, 7"diameter plastic reel DO-221AC (SlimSMA), 12 mm tape, 13"diameter plastic reel DO-214AB (SMC)/DO-215AB (SMCG), 16 mm tape, 13" diameter plastic reel DO-214AC (SMA), 12 mm tape, 7" diameter plastic reel DO-214BA (GF1), 12 mm tape, 7" diameter plastic reel Bulk pack for bridge and special axial-leaded formed devices 52.4 mm horizontal tape and ammo box packaging DFS bridge, 16 mm tape, 13" diameter paper reel TO-269AA (MB-S) bridge, 12 mm tape, 13" diameter paper reel TO-263AB 24 mm tape, 13" diameter reinforced hub plastic reel SMPD, 24 mm tape, 13" diameter plastic reel TO-263AB (wire bond) 24 mm tape, 13" diameter reinforced hub plastic reel DO-213AA (GL34) 8 mm tape, 13" diameter plastic reel DO-220AA (SMP) 12 mm tape, 7" diameter plastic reel DO-220AA (SMP) 12 mm tape, 13" diameter plastic reel TO-277A (SMPC), 12 mm tape, 7" diameter plastic reel TO-277A (SMPC), 12 mm tape, 13" diameter plastic reel Lead forming bulk packaging in anti-static bags MicroSMP, 8 mm tape, 7" diameter plastic reel Euroform, reel, cathode first off reel, lead coated Euroform, ammo pack, cathode first out of ammo pack, lead coated Euroform, reel, cathode last off reel, lead coated Euroform, ammo pack, cathode last out of ammo pack, lead coated Anti-static tube packaging for Bridge and Power Pack Anti-static tube packaging for wire bond TO-220, ITO-220, TO-262 and TO-263 DO-213AB (GL41), 12 mm tape, 7" diameter plastic reel DO-213AB (GL41), 12 mm tape, 13" diameter plastic reel DO-213AA (GL34), 8 mm tape, 7" diameter plastic reel MPG06 pseudo radial tape, cathode first out of ammo pack H P Tape in 7" diameter plastic reel I P Tape in 13" diameter plastic reel TR TR3 P P DO-214AC (SMA), 12 mm tape, 7" diameter plastic reel (1) DO-214AC (SMA), 12 mm tape, 13" diameter plastic reel (1) PACKAGING DESCRIPTION Notes (1) Formerly sold by Vishay Telefunken(R) (Telefunken(R) is a registered trademark of Electro Holding GmbH). * "P" and bold letter denotes preferred package code. * A "T" suffix added to the packaging codes for SMA, SMB and SMC products indicates that the patented folded-frame construction is used. This does not apply to TR and TR3 codes or TRANSZORB(R) TVS in SMA and SMB. Revision: 01-Feb-13 Document Number: 88869 1 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging Information www.vishay.com Vishay General Semiconductor BULK PACKAGING PREFERRED PACKAGE CODE PACKAGING DF-M, DF-S, DFL-S 45 GSIB-3S CASE TYPES BOX SIZE QUANTITY INCHES cm EA. Anti-static plastic tubes 17.4 length 44.1 length 50 45 Anti-static plastic tubes 25.1 length 63.9 length 20 GSIB-5S, PB 45 Anti-static plastic tubes 24.2 length 61.5 length 20 GBU, BU 45 Anti-static plastic tubes 18.5 length 47 length 20 GBL 45 Anti-static plastic tubes 17.5 length 44.5 length 20 KBPM 45 Anti-static plastic tubes 18.5 length 47 length 30 45, 4W Anti-static plastic tubes 21.0 length 53.7 length 50 TO-247AD 45 Anti-static plastic tubes 20.0 length 50.8 length 30 TO-269AA (MB-S) 45 Anti-static plastic tubes 20.3 x 0.41 51.5 x 1.04 100 KBPM 51 Anti-static PVC tray 12.5 x 6.5 x 1.25 31.7 x 16.5 x 3.17 600 GBL 51 Anti-static PVC tray 12.5 x 6.1 x 1.0 30.9 x 15.5 x 2.5 400 GBPC12-35W 51 Paper box 12.5 x 12.5 x 1.7 31.7 x 31.7 x 4.3 100 GBPC1, GBPC6 51 Paper box 7.5 x 7.5 x 1.43 19.0 x 19.0 x 3.6 100 KBL 51 Anti-static PVC tray 12.2 x 6.1 x 1.5 30.9 x 15.5 x 3.8 300 GBPC12-35 51 Paper box 12.5 x 12.5 x 1.7 31.7 x 31.7 x 4.3 100 KBU4, 6, 8 51 Anti-static PVC tray 12.2 x 6.1 x 1.5 30.9 x 15.5 x 3.8 250 WOG, 2WOG 51 Plastic bags - - 100 GBU, /BU 51 Paper tray 13.1 x 6.6 x 1.2 33.2 x 17.2 x 3.0 250 KBPM 72 Paper box 7.4 x 7.4 x 1.5 18.8 x 18.8 x 3.8 200 TO-220AB/AC, ITO-220AC/AB, TO-262AA Revision: 01-Feb-13 Document Number: 88869 2 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging Information www.vishay.com Vishay General Semiconductor AXIAL-LEADED TAPE AND REEL PACKAGING Inspection Hole (Both Sides) A C Ammo Pack can be Opened on Either Side, Depending on Desired Device Polarity B All axial-leaded devices are packed in accordance with EIA standard RS-296-E. The diagrams given below refer to these specifications. TABLE 1 - AMMO PACK PACKAGING PACKAGING 26 mm horizontal tape, ammo pack 52 mm horizontal tape, ammo pack AVAILABLE PRODUCT OUTLINES DO-204AL (DO-41), MPG06 DO-204AC P300 DO-204AL, MPG06 DO-204AC DO201AD, GP20 P600 PREFERRED PACKAGE CODE 53 53 53 73 73 73 73 GP10-E, RGP10-E, GP10-E, RGP10-E MPG06 Radial (avisert, panasert, euroform) vertical tape Pseudo/radial tape, ammo pack DIMENSION DIMENSION DIMENSION A B C 9.7" (247 mm) 1.7" (44 mm) 3.7" (95 mm) 10.0" (255 mm) 3.15" (80 mm) 4.53" (115 mm) 91, 93 13.4" (340 mm) 1.8" (47 mm) 7.9" (200 mm) 100 13.4" (340 mm) 1.8" (47 mm) 7.9" (200 mm) QUANTITY BOX 3.0K 1.5K 0.75K 3.0K 2.0K 1.0K 0.3K 2.0K 2.5K 2.0K 2.0K |D1 - D2| = 1.4 (0.055) Max. 0.8 (0.031) Max. Typ. 0.0 D1 D2 K C S A 0.8 (0.031) Max. E P E D Dia. (Table 2) Anode Lead White Tape B 6.0 0.4 T (0.236 0.0157) W Dimensions A, M, K, P, S and T apply to both sides Dimensions in millimeters (inches) Description Symbol Component Pitch A 2, 3 Inside Tape Spacing B 2, 3 Lead to Lead Eccentricity |D1 - D2| Lead Extension K Lead Bending E 2 Cumulative Pitch P 3 Exposed Adhesive S Tape Width T All polarized components shall be oriented in the same direction Fig. 1 Revision: 01-Feb-13 91.9 (3.62) Dia. 50.8 (2.00) Dia. 38.1 (1.50) Dia. 14.3 (0.56) Dia. Kraft Paper Cathode Lead Colored Tape The "C" dimension of Fig. 2 is between flanges of the component reel and shall be 1.5 mm (0.059") to 8.00 mm (0.315") greater than the overall taped component width "W" (Fig. 1). Where "W" dimension is 68.2 mm (2.68") max. Fig. 2 Document Number: 88869 3 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging Information www.vishay.com Vishay General Semiconductor AXIAL-LEADED TAPE AND REEL PACKAGING TABLE 2 - REEL AND AMMO PACK TAPING SPECIFICATIONS COMPONENT PITCH "A" Fig. 1 INSIDE TAPE SPACING "B" Fig. 1 PREFERRED PACKAGE CODE UNITS PER REEL EA. INCHES mm INCHES mm INCHES mm INCHES mm 1.5KA (PAR) 54 1400 0.395 10.0 2.06 52.4 13.0 330 0.047 1.2 DO-204AC 54 4000 0.200 5.0 2.06 52.4 13.0 330 0.047 1.2 DO-201AD 54 1400 0.395 10.0 2.06 52.4 13.0 330 0.047 1.2 DO-204AL 54 5500 0.200 5.0 2.06 52.4 13.0 330 0.047 1.2 COMPONENT CASE TYPE DFS Surface Mount REEL DIMENSION "D" Fig. 2 LEAD BENDING "E" Fig. 1 77 1500 - - 13.0 330 Fig. 13 - DO-214BA (GF1) 67A/5CA 1500/6500 - - 7.0/13.0 178/330 Fig. 13 - DO-213AA (GL34) 98/83 2500/9000 DO-213AB (GL41) 96/97 1500/5000 GP10E Radial Fig. 13 - - 7.0/13.0 178/330 Fig. 13 - - - 7.0/13.0 178/330 Fig. 13 - Fig. 7 and Fig. 8 2500 0.500 12.7 - - 13.0 330 0.079 2.0 GP10E 54 5500 0.200 5.0 2.06 52.4 13.0 330 0.047 1.2 GP20/1.5KE 54 1400 0.395 10.0 2.06 52.4 13.0 330 0.047 1.2 MPG06 100 5500 0.200 5.0 2.06 52.4 13.0 330 0.047 1.2 P600 54 800 0.395 10.0 2.06 52.4 13.0 330 0.047 1.2 84A/85A 3000/10 000 - - 7.0/13.0 178/330 Fig. 13 - 8A 2000 - - 13.0 330 Fig. 13 - DO-220AA (SMP) SMPD MicroSMP 89A 4500 - - 7.0 178 Fig. 13 - TO-277A (SMPC) 86A/87A 1500/6500 - - 7.0/13.0 178/330 Fig. 13 - DO-214AC (SMA) 61, 61T, TR/5A, 5AT, TR3 1800/7500 - - 7.0/13.0 178/330 Fig. 13 - - - 7.0/13.0 178/330 Fig. 13 - 850/3500 - - 7.0/13.0 178/330 Fig. 13 - 750 - - 13.0 330 Fig. 13 - DO-214AA (SMB)/ 52, 52T/5B, 5BT DO-215AA (SMBG) DO-214AB (SMC)/ 57T/9AT DO-215AB (SMCG) 750/3200 Fig. 13 DO-218AB 2D TO-263AB 81, 8W 800 - - 13.0 330 Fig. 13 - 80 3000 - - 13.0 330 Fig. 13 - 6A/6B 3500/14 000 - - 7.0/13.0 178/330 Fig. 13 - TO-269AA (MB-S) DO-221AC (SlimSMA) Note * Package codes, 61/5A, 52/5B are matrix-frame constructions for TRANSZORB(R) TVS in SMA and SMB only. TABLE 3 - COMPONENT AND INSIDE HORIZONTAL TAPE SPACING COMPONENT BODY DIAMETER COMPONENTS SPACING A (LEAD TO LEAD) INSIDE TAPE SPACING "B" 0 mm to 5 mm (0.0" to 0.197") 5.0 mm 0.5 mm (0.197" 0.020") 26 mm + 1.5 mm/- 0.0 mm (1.024" + 0.059"/- 0.0") 0 mm to 5 mm (0.0" to 0.197") 5.0 mm 0.5 mm (0.197" 0.020") 52.4 mm + 1.5 mm/- 0.4 mm (2.062" + 0.059"/- 0.016") 5.01 mm to 10 mm (0.197" to 0.394") 10 mm 0.5 mm (0.394" 0.020") 52.4 mm + 1.5 mm/- 0.4 mm (2.062" + 0.059"/- 0.016") Revision: 01-Feb-13 CUMULATIVE PITCH TOLERANCE Not to exceed 1.5 mm (0.059") over 6 consecutive components Document Number: 88869 4 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging Information www.vishay.com Vishay General Semiconductor DIMENSIONS in millimeters (inches) 12.7 (0.50) (Nominal) 7.35 (0.29) 5.35 (0.21) 1.0 (2) ( 0.039) 1.0 MAX. (2) (0.40) (Center to Center) 32.0 (1.26) 23.0 (0.905) 5.68 (0.224) 4.68 (0.184) 12.0 MAX. (Center to Center) (0.472) 2.72 (0.107) 2.03 (0.080) Body DIA. 6.5 MAX. (0.256) A (1) 20.5 18.5 (0.807) (0.728) 16.5 (0.650) 15.5 (0.610) Tape B (1) 2.5 11.0 MAX. MIN. (0.433) (0.098) Note: (1) Measurement difference between leads, A and B = 0.4 (0.016) MAX. (2) Component Alignment 0.65 (0.0256) 0.55 (0.022) Lead DIA. 0.6 MAX. (0.024) 9.75 (0.384) 8.50 (0.335) 4.3 (0.169) 3.7 (0.146) DIA. 4.55 (0.179) 3.15 (0.124) 19.0 (0.748) 17.5 (0.689) 13.5 (0.531) 12.5 (0.492) 13.0 (0.512) 12.4 (0.488) (Center to Center) 0.6 (0.025) 0.4 (0.016) User Direction Feed Available for GP10 Products only Utilizing 0.65 mm (0.025") Diameter Leads for Euroform tape by adding suffix "E" (GP10GE, 1N4004GPE). Lead coating is standard. Fig. 3 - Euroform 12.7 (0.50) (Nominal) 1.0 (1) ( 0.039) 1.0 MAX. (1) (0.40) (Center to Center) 5.68 (0.224) 4.68 (0.184) 6.5 MAX. (0.256) (Center to Center) 5.5 MIN. (0.217) 32.0 (1.26) 23.0 (0.905) 16.0 MIN. (0.630) 0.86 (0.034) 0.55 (0.022) Lead DIA. 1.3 MIN. (0.059) 16.5 (0.650) Tape 15.5 (0.610) 11.0 MAX. (0.433) 9.75 (0.384) 8.50 (0.335) 4.3 (0.169) 3.7 (0.146) DIA. Note: (1) Component Alignment 2.72 (0.107) 2.03 (0.080) Body DIA. 7.0 MIN. (0.276) 4.55 (0.179) 3.15 (0.124) (Center to Center) 0.6 (0.025) 0.4 (0.016) 19.0 (0.748) 17.5 (0.689) User Direction Feed 13.0 (0.512) 12.4 (0.488) Fig. 4 - Panasert Revision: 01-Feb-13 Document Number: 88869 5 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging Information www.vishay.com Vishay General Semiconductor DIMENSIONS in millimeters (inches) 1.0 (1) ( 0.039) 1.0 MAX. (1) (0.40) 12.7 (0.50) (Nominal) (Center to Center) 5.68 (0.224) 4.68 (0.184) (Center to Center) 32.0 (1.26) 23.0 (0.905) 2.72 (0.107) 2.03 (0.080) Body DIA. 6.5 MAX. (0.256) 5.5 MIN. (0.217) Tape 16.0 MIN. (0.630) 0.86 (0.034) 0.55 (0.022) Lead DIA. 3.0 MAX. (0.118) 16.5 (0.650) 15.5 (0.610) 11.0 MAX. (0.433) 9.75 (0.384) 8.50 (0.335) 0.6 (0.025) 0.4 (0.016) 4.55 (0.179) 3.15 (0.124) 19.0 (0.748) 17.5 (0.689) 4.3 (0.169) 3.7 (0.146) (Center to Center) 13.0 (0.512) 12.4 (0.488) Note: (1) Component Alignment User Direction Feed Available only for GP10 style products utilizing 0.65 mm (0.025") or 0.76 mm (0.030") diameter leads for Panasert and Avisert tape. Lead coating is available on GP10 products only. Standard Polarity Cathode Oriented Away from Sprocket Holes (Optional Polarity Cathode Oriented Toward Sprocket Holes) Fig. 5 - Avisert 1.0 MAX. (1) (0.40) 2.54 (0.01) 2.29 (0.090) Body DIA. 12.7 (0.50) (Nominal) 0.66 (0.026) 0.55 (0.022) Lead DIA. (Center to Center) 3.2 (0.125) 2.9 (0.115) 1.0 (1) ( 0.039) 1.0 (0.039) MAX. 16.0 (0.63) MIN. Tape 11.0 (4.33) MAX. 9.75 (0.384) 8.50 (0.335) 3.06 (0.118) MAX. 12.5 (0.492) MIN. 0.6 (0.025) 0.4 (0.016) 19.0 (0.748) 17.5 (0.689) 2.0 (0.079) MAX. 4.51 (0.178) 3.11 (0.122) Note: (1) Component Alignment 13.0 (0.51) 12.4 (0.49) 4.3 (0.169) 3.7 (0.146) 5.68 (0.224) DIA. 4.68 (0.184) User Direction Feed Available only for MPG06 Product in Ammo Pack in Accordance with EIA Standard RS-468-A Utilizing 0.61 mm (0.024") Diameter Leads. Maximum Cumulative Pitch Tolerance: 1.0 mm (0.039")/20 Pitch. Fig. 6 - Pseudo Radial Revision: 01-Feb-13 Document Number: 88869 6 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging Information www.vishay.com Vishay General Semiconductor RADIAL TAPE PACKAGING PKG91 PKG93 PKG90 PKG92 Fig. 7 and Fig. 8 - Reel and Ammo Box Packaging PREFERRED PACKAGE CODE EUROFORM PKG90, PKG91, PKG92, PKG93 "C" Arbor Hole DIA. 30 5 ID (1.181 0.197) Core DIA. 34.9 to 102 (1.37 to 4.02) 55 (2.17) MAX. 330 (13.0) MAX. Fig. 9 - Reel Dimensions Notes * "C" dimension between the reel flanges shall be governed by the overall width of the taped components and shall be 1.5 mm (0.057") to 8.0 mm (0.315") greater than the overall width * All leaded devices are packaged in accordance with EIA standard RS-468-A specification and are available on reel or in fan fold box (ammo pack) * All dimensions are in millimeters and (inches). The above packaging is only available from Taiwan. Revision: 01-Feb-13 Document Number: 88869 7 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging Information www.vishay.com Vishay General Semiconductor SURFACE MOUNT TAPE AND REEL PACKAGING Tape with Components shall Pass Around Bending Radius without Damage, for Reels with Hub Diameters Approaching Minimum Dimension Top Cover Tape Thickness: 0.10 mm (0.004") Max. Bending Radius R Ref. Fig. 11 Embossed Carrier Tape G Component Cavity N A B D T C Fig. 10 Fig. 12 DIMENSIONS in millimeters (inches) A MAX. B MIN. C D MIN. N MIN. G MAX. T MAX. 8 mm (0.315) 330 2.0 (13.0 0.079) 178 2.0 (7.0 0.079) 1.5 (0.059) 13.0 0.20 (0.51 0.0008) 20.2 (0.795) 50 (1.97) 9.9 (0.389) 14.4 (0.567) 12 mm (0.472) 330 2.0 (13.0 0.079) 178 2.0 (7.0 0.079) 1.5 (0.059) 13.0 0.20 (0.51 0.0008) 20.2 (0.795) 50 (1.97) 14.4 (0.567) 18.4 (0.724) 16 mm (0.630) 330 2.0 (13.0 0.079) 178 2.0 (7.0 0.079) 1.5 (0.059) 13.0 0.20 (0.51 0.0008) 20.2 (0.795) 50 (1.97) 18.4 (0.724) 22.4 (0.802) 24 mm (0.945) 330 2.0 (13.0 0.079) 178 2.0 (7.0 0.079) 1.5 (0.059) 13.0 0.20 (0.51 0.0008) 20.2 (0.795) 50 (1.97) 26.4 (1.039) 30.4 (1.197) TAPE SIZE Revision: 01-Feb-13 Document Number: 88869 8 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging Information www.vishay.com Vishay General Semiconductor SURFACE MOUNT TAPE AND REEL PACKAGING De-Reeling Direction P0 10 P0itches Cumulative Tolerance on Tape 0.2 P2 T2 T TVS Polarization D0 E Top Cover Tape A0 (2) F GL41, SMA, SMB, SMC, SMP, MicroSMP, SMPC, SlimSMA, DO-218AB/2E W K0 B1 (1) E2 B0 Rectifiers Polarization S1 T1 P1 Notes (1) For machine reference only, including draft and radii concentric around B0 (2) D1 for components 2.0 mm x 1.2 mm and larger DFS and MBS Polarization DO-218AB/2D See note 1 and table Fig. 13 8 mm, 12 mm, 16 mm, AND 24 mm EMBOSSED TAPE in millimeters (inches) TAPE SIZE 8 mm, 12 mm 16 mm, 24 mm D0 E1 P0 1.5 0.1 1.75 0.1 4.0 0.1 (0.059 0.004) (0.069 0.004) (0.157 0.004) P2 A0, B0, K0 S1 MIN. T MAX. T1 MAX. 2.0 0.05 (0.79 0.002) 2.0 0.1 (0.79 0.004) (1) 0.6 (0.024) 0.600 (0.024) 0.1 (0.004) DIMENSIONS in millimeters (inches) CASE TYPE DO-213AA (GL34) MicroSMP TAPE SIZE 8 (0.315) B1 MAX. D1 MIN. 4.2 (0.165) 3.28 (0.129) 1.0 (0.39) E2 MAX. F 6.25 (0.246) 6.05 (0.238) 3.5 0.05 (0.138 0.002) DO-213AB (GL41) DO-220AA (SMP) DFS TO-263AB DO-218AB SMPD DO-221AC (SlimSMA) 25 (0.984) 8.2 (0.323) 12 (0.472) 10.25 (0.404) 7.0 (2.76) 8.2 (0.323) TO-277A (SMPC) DO-214AA (SMB)/ DO-215AA (SMBG) DO-214AB (SMC)/ DO-215AB (SMCG) R REF. 4.0 0.10 (0.57 0.004) DO-214BA (GF1) DO-214AC(SMA) P1 5.5 0.05 (0.217 0.002) 1.5 (0.059) 8.0 0.10 30 (0.315 0.004) (1.181) 16 (0.630) 12.1 (0.476) 14.25 (0.561) 24 (0.945) 20.1 (0.791) 22.25 (0.876) 12 (0.472) 6.2 (0.244) 1.5 (0.059) 10.25 (0.404) 7.5 0.05 (0.295 0.002) 12.0 0.10 (0.472 0.004) 16.0 0.10 11.5 0.1 (0.630 0.004) (0.453 0.004) 12.0 0.10 (0.472 0.004) 5.5 0.05 4.0 0.10 (0.217 0.002) (0.157 0.001) T2 MAX. 2.4 (0.094) 1.919 (0.076) 4.5 (0.177) 3.25 (0.128) 2.64 (0.104) 1.84 (0.072) 1.43 (0.056) 2.77 (0.109) 2.64 (0.104) 3.91 (0.154) 5.31 (0.209) 2.35 (0.093) 1.53 (0.060) W 8.0 0.30 (0.315 0.012) 12.0 0.30 (0.472 0.012) 16.0 0.2 (0.630 0.008) 24.0 0.3 (0.945 0.008) 12.0 0.3 (0.472 0.012) Notes (1) A , B , and K are determined by the maximum dimensions of the component size. The clearance between the component and the cavity 0 0 0 must be within 0.05 mm (0.002") min. to 0.5 mm (0.02") max. for 8 mm tape and 12 mm tape, 0.15 mm (0.066") min. to 0.90 mm (0.035") max. for 16 mm tape and 0.15 mm (0.006") min. to 1.0 mm (0.59") max. for 24 mm tape. (2) All surface mount components are packed in accordance with EIA standard 481-C Revision: 01-Feb-13 Document Number: 88869 9 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000