© Semiconductor Components Industries, LLC, 2015
January, 2015 − Rev. 9 1Publication Order Number:
MC74AC05/D
MC74AC05, MC74ACT05
Hex Inverter with
Open-Drain Outputs
High−Performance Silicon−Gate CMOS
The MC74AC/ACT05 is identical in pinout to the LS05. The device
inputs are compatible with standard CMOS outputs; with pullup
resistors, they are compatible with TTL outputs.
Features
Outputs Source/Sink 24 mA
ACT05 Has TTL Compatible Inputs
These are Pb−Free Devices
GND
Figure 1. Pinout: 14-Lead Packages
1314 12 11 10 9 8
2134567
VCC A6Y6A5Y5A4Y4
A1Y1A2Y2A3Y3
Top View
Figure 2. Logic Diagram
Y*
2, 4, 6, 8, 10, 12
1, 3, 5, 9, 11, 13
A
PIN 14 = VCC
PIN 7 = GND
* DENOTES OPEN‐DRAIN OUTPUTS
www.onsemi.com
See detailed ordering and shipping information in the packag
e
dimensions section on page 4 of this data sheet.
ORDERING INFORMATION
FUNCTION TABLE
Input A
L
H
Output Y
Z
L
NOTE: Z = High Impedance
MARKING
DIAGRAMS
xxx = AC or ACT
A = Assembly Location
WL or L = Wafer Lot
Y = Year
WW or W = Work Week
G or G= Pb−Free Package
TSSOP−14
DT SUFFIX
CASE 948G
xxx
05
ALYWG
G
1
14
SOIC−14
D SUFFIX
CASE 751A
1
14
1
14
xxx05G
AWLYWW
1
14
(Note: Microdot may be in either location)
MC74AC05, MC74ACT05
www.onsemi.com
2
MAXIMUM RATINGS
Symbol Parameter Value Unit
VCC DC Supply Voltage *0.5 to )7.0 V
VIDC Input Voltage *0.5 v VI v VCC )0.5 V
VODC Output Voltage (Note 1) *0.5 v VO v VCC )0.5 V
IIK DC Input Diode Current $20 mA
IOK DC Output Diode Current $50 mA
IODC Output Sink/Source Current $50 mA
ICC DC Supply Current per Output Pin $50 mA
IGND DC Ground Current per Output Pin $50 mA
TSTG Storage Temperature Range *65 to )150 °C
TLLead temperature, 1 mm from Case for 10 Seconds 260 °C
TJJunction temperature under Bias )150 °C
qJA Ther mal Resistance (Note 2) SOIC
TSSOP 125
170 °C/W
PDPower Dissipation in Still Air at 85°C SOIC
TSSOP 125
170 mW
MSL Moisture Sensitivity Level 1
FRFlammability Rating Oxygen Index: 30% − 35% UL 94 V−0 @ 0.125 in
VESD ESD Withstand Voltage Human Body Model (Note 3)
Machine Model (Note 4)
Charged Device Model (Note 5)
> 2000
> 200
> 1000
V
ILatch−Up Latch−Up Performance Above VCC and Below GND at 85°C (Note 6) $100 mA
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be af fected.
1. IO absolute maximum rating must be observed.
2. The package thermal impedance is calculated in accordance with JESD51−7.
3. Tested to EIA/JESD22−A114−A.
4. Tested to EIA/JESD22−A115−A.
5. Tested to JESD22−C101−A.
6. Tested to EIA/JESD78.
RECOMMENDED OPERATING CONDITIONS
Symbol Parameter Min Typ Min Unit
VCC Supply Voltage AC 2.0 5.0 6.0 V
ACT 4.5 5.0 5.5
VREG DC Regulated Power Voltage (Ref. to GND) 0 VCC V
tr, tfInput Rise and Fall Time (Note 1)
AC Devices except Schmitt Inputs
VCC @ 3.0 V 150
VCC @ 4.5 V 40 ns/V
VCC @ 5.5 V 25
tr, tfInput Rise and Fall Time (Note 2)
ACT Devices except Schmitt Inputs VCC @ 4.5 V 10 ns/V
VCC @ 5.5 V 8.0
TJJunction Temperature (PDIP) 140 °C
TAOperating Ambient Temperature Range −40 25 85 °C
IOH Output Current − HIGH −24 mA
IOL Output Current − LOW 24 mA
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
1. Vin from 30% to 70% VCC; see individual Data Sheets for devices that differ from the typical input rise and fall times.
2. Vin from 0.8 V to 2.0 V; see individual Data Sheets for devices that differ from the typical input rise and fall times.
MC74AC05, MC74ACT05
www.onsemi.com
3
DC CHARACTERISTICS
Symbol Parameter VCC
(V)
74AC 74AC
Unit Conditions
TA = +25°C TA = −40°C to +85°C
Typ Guaranteed Limits
VIH Minimum High Level Input Voltage 3.0 1.5 2.1 2.1 VOUT = 0.1 V
4.5 2.25 3.15 3.15 V or VCC − 0.1 V
5.5 2.75 3.85 3.85
VIL Maximum Low Level Input Voltage 3.0 1.5 0.9 0.9 VOUT = 0.1 V
4.5 2.25 1.35 1.35 V or VCC − 0.1 V
5.5 2.75 1.65 1.65
VOL Maximum Low Level Output Voltage 3.0 0.002 0.1 0.1 IOUT = 50 mA
4.5 0.001 0.1 0.1 V
5.5 0.001 0.1 0.1
V
*VIN = VIL or VIH
3.0 0.36 0.44 12 mA
4.5 0.36 0.44 IOL 24 mA
5.5 0.36 0.44 24 mA
IIN Maximum Input Leakage Current 5.5 ±0.1 ±1.0 mAVI = VCC, GND
IOLD †Minimum Dynamic
Output Current 5.5 75 mA VOLD = 1.65 V Max
IOHD 5.5 −75 mA VOHD = 3.85 V Min
ICC Maximum Quiescent Supply Current 5.5 4.0 40 mAVIN = VCC or GND
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
*All outputs loaded; thresholds on input associated with output under test.
Maximum test duration 2.0 ms, one output loaded at a time.
NOTE: IIN and ICC @ 3.0 V are guaranteed to be less than or equal to the respective limit @ 5.5 V.
AC CHARACTERISTICS
Symbol Parameter VCC*
(V)
74AC 74AC
Unit
TA = +25°C CL = 50 pF TA = −40°C to + 85°C CL = 50 pF
Min Typ Max Min Max
tPZL Propagation Delay Output Enable 3.3 1.5 8.0 1.0 9.0 ns
5.0 1.5 6.0 1.0 6.5
tPLZ Propagation Delay Output Enable 3.3 1.5 8.0 1.0 9.0 ns
5.0 1.5 6.0 1.0 6.5
*Voltage Range 3.3 V is 3.3 V ±0.3 V.
Voltage Range 5.0 V is 5.0 V ±0.5 V.
MC74AC05, MC74ACT05
www.onsemi.com
4
DC CHARACTERISTICS
Symbol Parameter VCC
(V)
74ACT 74ACT
Unit Conditions
TA = +25°C TA = −40°C to +85°C
Typ Guaranteed Limits
VIH Minimum High Level Input Voltage 4.5
5.5 1.5
1.5 2.0
2.0 2.0
2.0 VVOUT = 0.1 V
or VCC − 0.1 V
VIL Maximum Low Level Input Voltage 4.5
5.5 1.5
1.5 0.8
0.8 0.8
0.8 VVOUT = 0.1 V
or VCC − 0.1 V
VOL Maximum Low Level Output Voltage 4.5
5.5 0.001
0.001 0.1
0.1 0.1
0.1 VIOUT = 50 mA
4.5
5.5
0.36
0.36 0.44
0.44 0.44 *VIN = VIL or VIH
IOH 24 mA
IIN Maximum Input Leakage Current 5.5 ±0.1 ±1.0 mAVI = VCC, GND
DICCT Additional Max. ICC/Input 5.5 0.6 1.5 mA VI = VCC 2.1 V
IOLD
IOHD
†Minimum Dynamic Output Current
5.5
5.5
75
−75 mA
mA VOLD = 1.65 V Max
VOHD = 3.85 V Min
ICC Maximum Quiescent Supply Current 5.5 4.0 40 mAVIN = VCC or GND
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
*All outputs loaded; thresholds on input associated with output under test.
Maximum test duration 2.0 ms, one output loaded at a time.
AC CHARACTERISTICS
Symbol Parameter VCC*
(V)
74ACT 74ACT
Unit
TA = +25°C CL = 50 pF TA = −40°C to +85°C CL = 50 pF
Min Typ Max Min Max
tPZL Propagation Delay Output Enable 5.0 1.5 8.0 1.0 8.5 ns
tPLZ Propagation Delay Output Enable 5.0 1.5 8.5 1.0 9.0 ns
*Voltage Range 5.0 V is 5.0 V ±0.5 V.
CAPACITANCE
Symbol Parameter Value Typ Unit Test Conditions
CIN Input Capacitance 4.5 pF VCC = 5.0 V
CPD Power Dissipation Capacitance 30 pF VCC = 5.0 V
ORDERING INFORMATION
Device Package Shipping
MC74AC05DG SOIC−14
(Pb−Free) 55 Units / Rail
MC74AC05DR2G SOIC−14
(Pb−Free) 2500 / Tape & Reel
MC74ACT05DG SOIC−14
(Pb−Free) 55 Units / Rail
MC74ACT05DR2G SOIC−14
(Pb−Free) 2500 / Tape & Reel
MC74ACT05DTR2G TSSOP−14
(Pb−Free) 2500 / Tape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
MC74AC05, MC74ACT05
www.onsemi.com
5
PACKAGE DIMENSIONS
SOIC−14 NB
CASE 751A−03
ISSUE K
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE PROTRUSION
SHALL BE 0.13 TOTAL IN EXCESS OF AT
MAXIMUM MATERIAL CONDITION.
4. DIMENSIONS D AND E DO NOT INCLUDE
MOLD PROTRUSIONS.
5. MAXIMUM MOLD PROTRUSION 0.15 PER
SIDE.
H
14 8
71
M
0.25 B M
C
h
X 45
SEATING
PLANE
A1
A
M
_
S
A
M
0.25 B S
C
b
13X
B
A
E
D
e
DET AIL A
L
A3
DET AIL A
DIM MIN MAX MIN MAX
INCHESMILLIMETERS
D8.55 8.75 0.337 0.344
E3.80 4.00 0.150 0.157
A1.35 1.75 0.054 0.068
b0.35 0.49 0.014 0.019
L0.40 1.25 0.016 0.049
e1.27 BSC 0.050 BSC
A3 0.19 0.25 0.008 0.010
A1 0.10 0.25 0.004 0.010
M0 7 0 7
H5.80 6.20 0.228 0.244
h0.25 0.50 0.010 0.019
__ __
6.50
14X
0.58
14X
1.18
1.27
DIMENSIONS: MILLIMETERS
1
PITCH
SOLDERING FOOTPRINT*
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
MC74AC05, MC74ACT05
www.onsemi.com
6
PACKAGE DIMENSIONS
TSSOP−14
CASE 948G
ISSUE B
DIM MIN MAX MIN MAX
INCHESMILLIMETERS
A4.90 5.10 0.193 0.200
B4.30 4.50 0.169 0.177
C−− 1.20 −− 0.047
D0.05 0.15 0.002 0.006
F0.50 0.75 0.020 0.030
G0.65 BSC 0.026 BSC
H0.50 0.60 0.020 0.024
J0.09 0.20 0.004 0.008
J1 0.09 0.16 0.004 0.006
K0.19 0.30 0.007 0.012
K1 0.19 0.25 0.007 0.010
L6.40 BSC 0.252 BSC
M0 8 0 8
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH
OR PROTRUSION SHALL NOT EXCEED 0.25
(0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN
EXCESS OF THE K DIMENSION AT MAXIMUM
MATERIAL CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE DETERMINED
AT DATUM PLANE −W−.
____
S
U0.15 (0.006) T
2X L/2
S
U
M
0.10 (0.004) V S
T
L−U−
SEATING
PLANE
0.10 (0.004)
−T−
ÇÇÇ
ÇÇÇ
SECTION N−N
DETAIL E
JJ1
K
K1
ÉÉÉ
ÉÉÉ
DETAIL E
F
M
−W−
0.25 (0.010)
8
14
7
1
PIN 1
IDENT.
H
G
A
D
C
B
S
U0.15 (0.006) T
−V−
14X REFK
N
N
7.06
14X
0.36 14X
1.26
0.65
DIMENSIONS: MILLIMETERS
1
PITCH
SOLDERING FOOTPRINT*
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
MC74AC05, MC74ACT05
www.onsemi.com
7
P
UBLICATION ORDERING INFORMATION
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
MC74AC05/D
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your loc
al
Sales Representative
ON Semiconductor and the are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−M arking.pdf. S CILLC reserves the r ight to make changes without f urther n otice to a ny products herein. S CILLC makes n o warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all l iabilit y, including without limitation special, consequential or i ncident al d amages. Typical” parameters w hich m ay be provided in SCI LLC d at a sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application b y c ust omer’s technical e xperts. SCILLC d oes n ot c onvey a ny license under i t s p at ent r ights n or t he r ights o f o t hers. SCILLC p roducts a re n ot d esigned, i ntended,
or authorized for use as c omponent s i n s yst ems i nt ended f or s urgic al i m plant i nt o the body, or other applications intended to support or sust ain life, o r f or a ny o ther a pplicat ion in w hich
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC an d it s officers, employees, subsidiaries, a ffiliates, and distributors harmless against all claims, costs, damages, and
expenses, and r easonable a ttorney f ees a rising o ut of, d irect ly o r i ndirectly, any claim o f p ersonal i njury o r d eath a ssociated w ith s uch u nintended o r u nauthorized u se, even i f s uch c laim
alleges that SCILLC was negligent regarding the d esign or manufacture of the p art. SCILLC is a n E qual O pportunity/ Affirmat ive A ction E mployer . T his l iterature i s subject to all applicable
copyright laws and is not for resale in any manner.