LM4953 LM4953 Ground-Referenced, Ultra Low Noise, Ceramic Speaker Driver Literature Number: SNAS299E LM4953 Ground-Referenced, Ultra Low Noise, Ceramic Speaker Driver General Description Key Specifications The LM4953 is an audio power amplifier designed for driving Ceramic Speaker in portable applications. When powered by a 3.6V supply, it is capable of forcing 12.6Vpp across a 2F + 30 bridge-tied-load (BTL) with less than 1% THD+N. Boomer audio power amplifiers were designed specifically to provide high quality output power with a minimal amount of external components. The LM4953 does not require bootstrap capacitors, or snubber circuits. Therefore it is ideally suited for display applications requiring high power and minimal size. The LM4953 features a low-power consumption shutdown mode. Additionally, the LM4953 features an internal thermal shutdown protection mechanism. The LM4953 contains advanced pop & click circuitry that eliminates noises which would otherwise occur during turn-on and turn-off transitions. The LM4953 is unity-gain stable and can be configured by external gain-setting resistors. j Quiescent Power Supply Current (Vdd = 3V) 7mA(typ) j BTL Voltage Swing (2F+30 load, 1% THD+N, Vdd = 3.6V) j Shutdown Current 12.6Vpp (typ) 1A (max) Features n Pop & click circuitry eliminates noise during turn-on and turn-off transitions n Low, 1A (max) shutdown current n Low, 7mA (typ) quiescent current n 12.6Vpp mono BTL output, load = 2F+ 30 n Thermal shutdown n Unity-gain stable n External gain configuration capability Applications n Cellphone n PDA Typical Application 20142168 FIGURE 1. Typical Application Circuit Boomer (R) is a registered trademark of National Semiconductor Corporation. (c) 2006 National Semiconductor Corporation DS201421 www.national.com LM4953 Ground-Referenced, Ultra Low Noise, Ceramic Speaker Driver February 2006 LM4953 Connection Diagram LLP Package 20142101 Top View Order Number LM4953SD See NS Package Number SDA14A Pin Descriptions Pin Name Function 1 SD Active Low Shutdown 2 CPVDD Charge Pump Power Supply 3 CCP+ Positive Terminal - Charge Pump Flying Capacitor 4 PGND Power Ground 5 CCP- Negative Terminal - Charge Pump Flying Capacitor 6 VCP_OUT Charge Pump Output 7 NC No Connect 8 AVSS Negative Power Supply - Amplifier 9 OUT B Output B 10 AVDD Positive Power Supply - Amplifier 11 OUT A Output A 12 NC No Connect 13 VIN Signal Input 14 SGND Signal Ground www.national.com 2 Junction Temperature If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Thermal Resistance Supply Voltage (VDD) 4.5V Storage Temperature -65C to +150C Input Voltage See AN-1187 'Leadless Leadframe Packaging (LLP).' Operating Ratings Temperature Range -0.3V to VDD + 0.3V Power Dissipation (Note 3) TMIN TA TMAX -40C TA 85C Supply Voltage (VDD) 1.6V VDD 4.2V Internally Limited ESD Susceptibility (Note 4) 2000V ESD Susceptibility (Note 5) 200V 150C Electrical Characteristics VDD = 3.6V The following specifications apply for VDD = 3.6V, AV-BTL = 6dB, ZL = 2F+30 unless otherwise specified. Limits apply to TA = 25C. See Figure 1. Symbol Parameter Conditions LM4953 Typ (Note 6) Units (Limits) Limit (Notes 7, 8) IDD Quiescent Power Supply Current VIN = 0, RLOAD = 2F+30 8 mA (max) Istandby Quiescent Power Supply Current Auto Standby Mode VIN = 0, ZLOAD = 2F+30 2.7 mA ISD Shutdown Current VSD = GND 0.1 VSDIH Shutdown Voltage Input High SD1 SD2 0.7*CPVdd VSDIL Shutdown Voltage Input Low SD1 SD2 0.3*CPVdd TWU Wake-up Time VOS Output Offset Voltage 1 125 A (max) V (min) V (max) sec 1 10 mV (max) VOUT Output Voltage Swing THD = 1% (max); f = 1kHz RL = 2F+30, Mono BTL THD+N Total Harmonic Distortion + Noise VOUT = 6Vp-p, fIN = 1kHz OS Output Noise A-Weighted Filter, VIN = 0V 15 V VRIPPLE = 200mVp-p, f = 217Hz, Input Referred 67 dB PSRR Power Supply Rejection Ratio VRIPPLE = 200mVp-p, f = 1kHz, Input Referred 65 dB ZL = 2F+30, VOUT = 6Vp-p 105 dB SNR Signal-to-Noise Ratio 12.6 Vpp 0.02 % Electrical Characteristics VDD = 3.0V The following specifications apply for VDD = 3.0V, AV-BTL = 6dB, ZL = 2F+30 unless otherwise specified. Limits apply to TA = 25C. See Figure 1. Symbol Parameter Conditions LM4953 Units (Limits) Typ (Note 6) Limit (Notes 7, 8) 10 IDD Quiescent Power Supply Current VIN = 0, ZLOAD = 2F+30 7 Istandby Quiescent Power Supply Current Auto Standby Mode VIN = 0, ZLOAD = 2F+30 2.3 ISD Shutdown Current VSD-LC = VSD-RC = GND 0.1 VSDIH SD1 Shutdown Voltage Input High SD2 mA 1 0.7*CPVdd 3 mA (max) A (max) V (min) www.national.com LM4953 Absolute Maximum Ratings (Notes 1, 2) LM4953 Electrical Characteristics VDD = 3.0V (Continued) The following specifications apply for VDD = 3.0V, AV-BTL = 6dB, ZL = 2F+30 unless otherwise specified. Limits apply to TA = 25C. See Figure 1. Symbol Parameter Conditions LM4953 Typ (Note 6) VSDIL Shutdown Voltage Input Low SD1 SD2 Units (Limits) Limit (Notes 7, 8) 0.3*CPVdd V (max) TWU Wake-up Time VOS Output Offset Voltage VOUT Output Voltage Swing THD = 1% (max); f = 1kHz ZL = 2F+30, Mono BTL 10.2 Vpp THD+N Total Harmonic Distortion + Noise VOUT = 8.5Vp-p, fIN = 1kHz 0.02 % OS Output Noise A-Weighted Filter, VIN = 0V 15 V VRIPPLE = 200mVp-p, f = 217Hz, Input Referred 73 dB VRIPPLE = 200mVp-p, f = 1kHz, Input Referred 68 dB ZL = 2F+30, VOUT = 8.5Vp-p 105 dB PSRR SNR Power Supply Rejection Ratio Signal-to-Noise Ratio 125 1 sec 10 mV (max) Note 1: All voltages are measured with respect to the GND pin unless otherwise specified. Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions that guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given; however, the typical value is a good indication of device performance. Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature, TA. The maximum allowable power dissipation is PDMAX = (TJMAX - TA)/JA or the number given in Absolute Maximum Ratings, whichever is lower. For the LM4xxx typical application (shown in Figure 1) with VDD = yyV, RL = 2F+30 mono BTL operation the total power dissipation is xxxW. JA = 40C/W. Note 4: Human body model, 100pF discharged through a 1.5k resistor. Note 5: Machine Model, 220pF-240pF discharged through all pins. Note 6: Typicals are measured at 25C and represent the parametric norm. Note 7: Limits are guaranteed to National's AOQL (Average Outgoing Quality Level). Note 8: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis. Note 9: If the product is in shutdown mode and VDD exceeds 3.6V (to a max of 4V VDD), then most of the excess current will flow through the ESD protection circuits. If the source impedance limits the current to a max of 10mA, then the part will be protected. If the part is enabled when VDD is above 4V, circuit performance will be curtailed or the part may be permanently damaged. www.national.com 4 LM4953 Typical Performance Characteristics THD+N vs Frequency VDD = 3V, VO = 6Vpp, ZL = 2F+30 THD+N vs Frequency VDD = 2V, VO = 2Vpp, ZL = 2F+30 20142112 20142113 THD+N vs Frequency VDD = 4.2V, VO = 10Vpp, ZL = 2F+30 THD+N vs Frequency VDD = 3.6V, VO = 8.5Vpp, ZL = 2F+30 20142114 20142118 THD+N vs Output Voltage VDD = 3V, f = 1kHz, ZL = 2F+30 THD+N vs Output Voltage VDD = 2V, f = 1kHz, ZL = 2F+30 20142121 20142119 5 www.national.com LM4953 Typical Performance Characteristics (Continued) THD+N vs Output Voltage VDD = 3.6V, f = 1kHz, ZL = 2F+30 THD+N vs Output Voltage VDD = 4.2V, f = 1kHz, ZL = 2F+30 20142120 20142122 PSRR vs Frequency VDD = 3V, ZL = 2F+30 PSRR vs Frequency VDD = 2V, ZL = 2F+30 20142123 20142125 PSRR vs Frequency VDD = 4.2V, ZL = 2F+30 PSRR vs Frequency VDD = 3.6V, ZL = 2F+30 20142124 www.national.com 20142126 6 LM4953 Typical Performance Characteristics (Continued) Supply Current vs Supply Voltage ZL = 2F+30 20142127 7 www.national.com LM4953 OUTPUT TRANSIENT ('CLICK AND POPS') ELIMINATED The LM4953 contains advanced circuitry that virtually eliminates output transients ('clicks and pops'). This circuitry prevents all traces of transients when the supply voltage is first applied or when the part resumes operation after coming out of shutdown mode. Application Information ELIMINATING THE OUTPUT COUPLING CAPACITOR The LM4953 features a low noise inverting charge pump that generates an internal negative supply voltage. This allows the outputs of the LM4953 to be biased about GND instead of a nominal DC voltage, like traditional headphone amplifiers. Because there is no DC component, the large DC blocking capacitors (typically 220F) are not necessary. The coupling capacitors are replaced by two, small ceramic charge pump capacitors, saving board space and cost. Eliminating the output coupling capacitors also improves low frequency response. In traditional headphone amplifiers, the headphone impedance and the output capacitor form a high pass filter that not only blocks the DC component of the output, but also attenuates low frequencies, impacting the bass response. Because the LM4953 does not require the output coupling capacitors, the low frequency response of the device is not degraded by external components. POWER DISSIPATION Power dissipation is a major concern when using any power amplifier and must be thoroughly understood to ensure a successful design. Equation 1 states the maximum power dissipation point for a single-ended amplifier operating at a given supply voltage and driving a specified output load. PDMAX = (VDD) / (22ZL) (1) Since the LM4953 has two operational amplifiers in one package, the maximum internal power dissipation point is twice that of the number which results from Equation 1. Even with large internal power dissipation, the LM4953 does not require heat sinking over a large range of ambient temperatures. The maximum power dissipation point obtained must not be greater than the power dissipation that results from Equation 2: In addition to eliminating the output coupling capacitors, the ground referenced output nearly doubles the available dynamic range of the LM4953 when compared to a traditional headphone amplifier operating from the same supply voltage. BRIDGE CONFIGURATION EXPLANATION The Audio Amplifier portion of the LM4953has two internal amplifiers allowing different amplifier configurations. The first amplifier's gain is externally configurable, whereas the second amplifier is internally fixed in a unity-gain, inverting configuration. The closed-loop gain of the first amplifier is set by selecting the ratio of Rf to Ri while the second amplifier's gain is fixed by the two internal 20k resistors. Figure 1 shows that the output of amplifier one serves as the input to amplifier two. This results in both amplifiers producing signals identical in magnitude, but out of phase by 180. Consequently, the differential gain for the Audio Amplifier is PDMAX = (TJMAX - TA) / (JA) (2) Depending on the ambient temperature, TA, of the system surroundings, Equation 2 can be used to find the maximum internal power dissipation supported by the IC packaging. If the result of Equation 1 is greater than that of Equation 2, then either the supply voltage must be decreased, the load impedance increased or TA reduced. Power dissipation is a function of output power and thus, if typical operation is not around the maximum power dissipation point, the ambient temperature may be increased accordingly. AVD = 2 *(Rf/Ri) POWER SUPPLY BYPASSING As with any power amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection. Applications that employ a 3V power supply typically use a 4.7F capacitor in parallel with a 0.1F ceramic filter capacitor to stabilize the power supply's output, reduce noise on the supply line, and improve the supply's transient response. Keep the length of leads and traces that connect capacitors between the LM4953's power supply pin and ground as short as possible. By driving the load differentially through outputs OUT A and OUT B, an amplifier configuration commonly referred to as "bridged mode" is established. Bridged mode operation is different from the classic single-ended amplifier configuration where one side of the load is connected to ground. A bridge amplifier design has a few distinct advantages over the single-ended configuration. It provides differential drive to the load, thus doubling the output swing for a specified supply voltage. Four times the output power is possible as compared to a single-ended amplifier under the same conditions. This increase in attainable output power assumes that the amplifier is not current limited or clipped. In order to choose an amplifier's closed-loop gain without causing excessive clipping, please refer to the Audio Power Amplifier Design section. The bridge configuration also creates a second advantage over single-ended amplifiers. Since the differential outputs, OUT A and OUT B, are biased at half-supply, no net DC voltage exists across the load. This eliminates the need for an output coupling capacitor which is required in a single supply, single-ended amplifier configuration. Without an output coupling capacitor, the half-supply bias across the load would result in both increased internal IC power dissipation and also possible loudspeaker damage. www.national.com 2 AUTOMATIC STANDBY MODE The LM4953 features Automatic Standby Mode circuitry (patent pending). In the absence of an input signal, after approximately 3 seconds, the LM4953 goes into low current standby mode. The LM4953 recovers into full power operating mode immediately after a signal, which is greater than the input threshold voltage, is applied to either the left or right input pins. The input threshold voltage is not a static value, as the supply voltage increases, the input threshold voltage decreases. This feature reduces power supply current consumption in battery operated applications. To ensure correct operation of Automatic Standby Mode, proper layout techniques should be implemented. Separating PGND and SGND can help reduce noise entering the LM4953 in noisy environments. It is also important to use 8 negative supply. Higher ESR capacitors result in reduced output power from the audio amplifiers. Charge pump load regulation and output impedance are affected by the value of the flying capacitor (C1). A larger valued C1 (up to 3.3uF) improves load regulation and minimizes charge pump output resistance. Beyond 3.3uF, the switch-on resistance dominates the output impedance for capacitor values above 2.2uF. (Continued) correct power off sequencing. The device should be in shutdown and then powered off in order to ensure proper functionality of the Auto-Standby feature. While Automatic Standby Mode reduces power consumption very effectively during silent periods, maximum power saving is achieved by putting the device into shutdown when it is not in use. The output ripple is affected by the value and ESR of the output capacitor (C2). Larger capacitors reduce output ripple on the negative power supply. Lower ESR capacitors minimize the output ripple and reduce the output impedance of the charge pump. MICRO POWER SHUTDOWN The voltage applied to the SD controls the LM4953's shutdown function. When active, the LM4953's micropower shutdown feature turns off the amplifiers' bias circuitry, reducing the supply current. The trigger point is 0.3*CPVDD for a logic-low level, and 0.7*CPVDD for logic-high level. The low 0.01A (typ) shutdown current is achieved by applying a voltage that is as near as ground a possible to the SD pins. A voltage that is higher than ground may increase the shutdown current. The LM4953 charge pump design is optimized for 2.2uF, low ESR, ceramic, flying, and output capacitors. Input Capacitor Value Selection Amplifying the lowest audio frequencies requires high value input coupling capacitors (Ci in Figure 1). A high value capacitor can be expensive and may compromise space efficiency in portable designs. In many cases, however, the speakers used in portable systems, whether internal or external, have little ability to reproduce signals below 150Hz. Applications using speakers with this limited frequency response reap little improvement by using high value input and output capacitors. Besides affecting system cost and size, Ci has an effect on the LM4953's click and pop performance. The magnitude of the pop is directly proportional to the input capacitor's size. Thus, pops can be minimized by selecting an input capacitor value that is no higher than necessary to meet the desired -3dB frequency. As shown in Figure 1, the internal input resistor, Ri and the input capacitor, Ci, produce a -3dB high pass filter cutoff frequency that is found using Equation (3). Conventional headphone amplifiers require output capacitors; Equation (3) can be used, along with the value of RL, to determine towards the value of output capacitor needed to produce a -3dB high pass filter cutoff frequency. There are a few ways to control the micro-power shutdown. These include using a single-pole, single-throw switch, a microprocessor, or a microcontroller. When using a switch, connect an external 100k pull-up resistor between the SD pins and VDD. Connect the switch between the SD pins and ground. Select normal amplifier operation by opening the switch. Closing the switch connects the SD pins to ground, activating micro-power shutdown. The switch and resistor guarantee that the SD pins will not float. This prevents unwanted state changes. In a system with a microprocessor or microcontroller, use a digital output to apply the control voltage to the SD pins. Driving the SD pins with active circuitry eliminates the pull-up resistor. EXPOSED-DAP CONSIDERATIONS It is essential that the exposed Die Attach Paddle (DAP), for the LM4953, is NOT connected to GND. For optimal operation it should be connected to AVss and VCP-OUT (Pins 6 and 8). SELECTING PROPER EXTERNAL COMPONENTS Optimizing the LM4953's performance requires properly selecting external components. Though the LM4953 operates well when using external components with wide tolerances, best performance is achieved by optimizing component values. fi-3dB = 1 / 2RiCi (3) Also, careful consideration must be taken in selecting a certain type of capacitor to be used in the system. Different types of capacitors (tantalum, electrolytic, ceramic) have unique performance characteristics and may affect overall system performance. (See the section entitled Charge Pump Capacitor Selection.) Charge Pump Capacitor Selection Use low ESR (equivalent series resistance) ( < 100m) ceramic capacitors with an X7R dielectric for best performance. Low ESR capacitors keep the charge pump output impedance to a minimum, extending the headroom on the 9 www.national.com LM4953 Application Information LM4953 Application Information (Continued) LM4953 DEMO BOARD ARTWORK Top Layer Mid Layer 1 20142195 20142194 Mid Layer 2 Bottom Layer 20142197 20142196 www.national.com 10 LM4953 Revision History Rev Date Description 1.0 2/18/05 Started D/S by copying LM4926 (DS201161). 1.2 9/13/05 Added the Typ Perf curves and Application Info section. 1.3 9/14/05 Added more Typ Perf curves. First WEB release on the D/S. 1.4 9/19/05 Fixed some typo, then re-released D/S to the WEB. 1.5 11/11/05 Added the LLP boards, then re-released D/S to the WEB... not released on this date.. 1.6 11/14/05 Added the LLP boards, then re-released D/S to the WEB (per Nisha). 1.7 11/15/05 Text edit. 1.8 12/21/05 Added the EXPOSED-DAP CONSIDERATIONS (Application Info section), then re-released D/S to the WEB. 1.9 2/01/06 Edited 20142168 (Typ Appl ckt)..., then re-released D/S to the WEB. 11 www.national.com LM4953 Ground-Referenced, Ultra Low Noise, Ceramic Speaker Driver Physical Dimensions inches (millimeters) unless otherwise noted LLP Package Order Number LM4953SD NS Package Number SDA14A National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated