1995 Aug 08 2
Philips Components
Non-solid Al - electrolytic capacitors Mounting Accessories
MECHANICAL DATA
Clamps for ST - versions, ∅D = 35, 50, 65 and 75 mm
To facilitate vertical mounting, a series of rigid clamps
made of zinc plated steel are available.
The clamps have either two or three mounting lugs, may
be easily slipped over the capacitor and then clamped with
a nut and bolt. Four types of clamps are available, one for
each case diameter.
They are delivered without nuts or bolts.
To avoid damaging the insulation sleeve, do not
overtighten the clamp screw.
Fig.1 Dimensional outline of clamp for
case ∅D = 35 mm.
Dimensions in mm.
Catalogue number: 4322 043 04272.
For dimensions see Table 2.
handbook, halfpage
MBC637
4.5 0
0.5
10 O4.5 0.1
12
0.5
e
b
a
12 0.5
6 1
1
35o
d
Dimensions in mm.
Catalogue number: 4322 043 04281.
Fig.2 Dimensional outline of clamp for
case ∅D = 50 mm.
handbook, halfpage
MBC636
10.5 4 min
50
49
67.5
66.5
80 max
12.05
11.05
7
61
60o
60o
4.4 minO
12.5
max
1995 Aug 08 3
Philips Components
Non-solid Al - electrolytic capacitors Mounting Accessories
Fig.3 Dimensional outline of clamp for
case ∅D = 65 mm.
Dimensions in mm.
Catalogue number: 4322 043 04291.
handbook, halfpage
MBC598
4.4 minO
4.5
65
64
88.5
87.5
101 max
12.5
max
12.5
11.5
7
61
60o
60o
10.5
Fig.4 Dimensional outline of clamp for
case ∅D = 75 mm.
Dimensions in mm.
Catalogue number: 4322 043 12991.
handbook, halfpage
MBC599
12.5
max
1
74
110 1
98 0.5
1
0
4.5 1O
4.5 0.2
6 0.2
12
0.5
6 1
60o
60o
10.5 0.5
0
5.5 0.5
0
1995 Aug 08 4
Philips Components
Non-solid Al - electrolytic capacitors Mounting Accessories
handbook, halfpage
MGB119
D
8.4
0.2
Nuts and washers for STB - versions
When mounting with the bolt, which is an integral part of
the case, standard metal M8 and M12 nuts and washers
may be used; the maximum permissible torque is 4 Nm for
M8 nuts and 10 Nm for M12 nuts.
If insulated mounting is required, synthetic nuts and rubber
washers are available; for these nuts the maximum
permissible torque is 2 Nm (M8) and 4 Nm (M12).
Fig.5 Insulated mounting.
handbook, halfpage
MGB114
rubber
washer
Fig.6 Synthetic cap nut; see Table 1
for dimensions D, H and W.
Dimensions in mm.
handbook, halfpage
MGB115
17 0.3O
W
6
1
H
D
Table 1 Dimensions of synthetic cap nut; see Fig.6
Note
1. Dimension W is measured across flats.
CASE
DIAMETER
(mm) THREAD D
(mm) H
(mm)
W
(note 1)
(mm)
MIN. THREADED
DEPTH
(mm) CATALOGUE NUMBER
35 M8 25 15 17 11.5 4322 043 05561
≥50 M12 30 20 19 15.5 4322 043 05571
Fig.7 Rubber washer; thickness 2 mm.
Rubber washer ordering codes
D
(mm) D
(mm) CATALOGUE NUMBER
34 8.4 4322 043 05591
49 13 4322 043 05531
64 13 4322 043 05521
74 13 4322 043 13001
1995 Aug 08 5
Philips Components
Non-solid Al - electrolytic capacitors Mounting Accessories
Clamps for SL - versions, ∅D = 25, 30, 35 and 40 mm
To facilitate vertical mounting, a series of rigid clamps
made of zinc plated steel are available.
The clamps have two mounting lugs, may be easily slipped
over the capacitor and then clamped with a nut and bolt.
Four types of clamps are available, one for each case
diameter.
They are delivered without nuts or bolts.
To avoid damaging the insulation sleeve, do not
overtighten the clamp screw.
Fig.8 Dimensional outline of clamp for
case ∅D = 25, 30 and 40 mm.
Dimensions in mm.
For dimensions see Table 2.
handbook, halfpage
MGB116
30o
4.3
O 4.0 0.2
10
1.0
e
a
b
d
10c
1+ 0.2
0
13.5
3
7
Fig.9 Dimensional outline of clamp for
case ∅D = 35 mm.
Dimensions in mm.
For dimensions see Table 2.
handbook, halfpage
MBC637
4.5 0
0.5
10 O4.5 0.1
12
0.5
e
b
a
12 0.5
6 1
1
35o
d
Table 2 Clamp dimensions; see Figs 1, 8 and 9
CASE
DIAMETER
(mm)
a
(mm) b
(mm) c
(mm) d
(mm) e
(mm) CATALOGUE NUMBER
25 41.5 ±0.2 25 35 18.5 56 4322 043 03301
30 46.5 ±0.2 30 40 21 61 4322 043 03311
35 51.5 ±0.2 35 −23.5 63 4322 043 04272
40 56.5 ±0.2 40 50 26 71 4322 043 03331
