STM32F051x4 STM32F051x6 STM32F051x8 ARM(R)-based 32-bit MCU, 16 to 64 KB Flash, 11 timers, ADC, DAC and communication interfaces, 2.0-3.6 V Datasheet - production data Features &"'! (R) (R) * Core: ARM 32-bit Cortex -M0 CPU, frequency up to 48 MHz * Memories - 16 to 64 Kbytes of Flash memory - 8 Kbytes of SRAM with HW parity checking * CRC calculation unit * Reset and power management - Digital and I/O supply: VDD = 2.0 V to 3.6 V - Analog supply: VDDA = from VDD to 3.6 V - Power-on/Power down reset (POR/PDR) - Programmable voltage detector (PVD) - Low power modes: Sleep, Stop, Standby - VBAT supply for RTC and backup registers * Clock management - 4 to 32 MHz crystal oscillator - 32 kHz oscillator for RTC with calibration - Internal 8 MHz RC with x6 PLL option - Internal 40 kHz RC oscillator * Up to 55 fast I/Os - All mappable on external interrupt vectors - Up to 36 I/Os with 5 V tolerant capability * 5-channel DMA controller * One 12-bit, 1.0 s ADC (up to 16 channels) - Conversion range: 0 to 3.6 V - Separate analog supply from 2.4 up to 3.6 * One 12-bit DAC channel * Two fast low-power analog comparators with programmable input and output * Up to 18 capacitive sensing channels supporting touchkey, linear and rotary touch sensors * Up to 11 timers - One 16-bit 7-channel advanced-control timer for 6 channels PWM output, with deadtime generation and emergency stop - One 32-bit and one 16-bit timer, with up to 4 IC/OC, usable for IR control decoding December 2015 This is information on a product in full production. LQFP64 10x10 mm UFQFPN48 7x7 mm UFBGA64 UFQFPN32 5x5 mm 5x5 mm LQFP48 7x7 mm LQFP32 7x7 mm WLCSP36 2.6x2.7 mm - One 16-bit timer, with 2 IC/OC, 1 OCN, deadtime generation and emergency stop - Two 16-bit timers, each with IC/OC and OCN, deadtime generation, emergency stop and modulator gate for IR control - One 16-bit timer with 1 IC/OC - Independent and system watchdog timers - SysTick timer: 24-bit downcounter - One 16-bit basic timer to drive the DAC * Calendar RTC with alarm and periodic wakeup from Stop/Standby * Communication interfaces - Up to two I2C interfaces, one supporting Fast Mode Plus (1 Mbit/s) with 20 mA current sink, SMBus/PMBus and wakeup from Stop mode - Up to two USARTs supporting master synchronous SPI and modem control, one with ISO7816 interface, LIN, IrDA capability, auto baud rate detection and wakeup feature - Up to two SPIs (18 Mbit/s) with 4 to 16 programmable bit frame, one with I2S interface multiplexed * HDMI CEC interface, wakeup on header reception * Serial wire debug (SWD) * 96-bit unique ID (R) * All packages ECOPACK 2 Table 1. Device summary Reference STM32F051xx DocID022265 Rev 6 Part number STM32F051C4, STM32F051K4, STM32F051R4 STM32F051C6, STM32F051K6, STM32F051R6 STM32F051C8, STM32F051K8, STM32F051R8, STM32F051T8 1/121 www.st.com Contents STM32F051x4 STM32F051x6 STM32F051x8 Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3 Functional overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.1 ARM(R)-Cortex(R)-M0 core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.2 Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.3 Boot modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.4 Cyclic redundancy check calculation unit (CRC) . . . . . . . . . . . . . . . . . . . 14 3.5 Power management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Power supply schemes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.5.2 Power supply supervisors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.5.3 Voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.5.4 Low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3.6 Clocks and startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3.7 General-purpose inputs/outputs (GPIOs) . . . . . . . . . . . . . . . . . . . . . . . . . 16 3.8 Direct memory access controller (DMA) . . . . . . . . . . . . . . . . . . . . . . . . . . 17 3.9 Interrupts and events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 3.10 2/121 3.5.1 3.9.1 Nested vectored interrupt controller (NVIC) . . . . . . . . . . . . . . . . . . . . . . 17 3.9.2 Extended interrupt/event controller (EXTI) . . . . . . . . . . . . . . . . . . . . . . 17 Analog-to-digital converter (ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 3.10.1 Temperature sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3.10.2 Internal voltage reference (VREFINT) . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3.10.3 VBAT battery voltage monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 3.11 Digital-to-analog converter (DAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 3.12 Comparators (COMP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 3.13 Touch sensing controller (TSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 3.14 Timers and watchdogs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 3.14.1 Advanced-control timer (TIM1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 3.14.2 General-purpose timers (TIM2, 3, 14, 15, 16, 17) . . . . . . . . . . . . . . . . . 22 3.14.3 Basic timer TIM6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 3.14.4 Independent watchdog (IWDG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 3.14.5 System window watchdog (WWDG) . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 3.14.6 Contents SysTick timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3.15 Real-time clock (RTC) and backup registers . . . . . . . . . . . . . . . . . . . . . . 23 3.16 Inter-integrated circuit interface (I2C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 3.17 Universal synchronous/asynchronous receiver/transmitter (USART) . . . 25 3.18 Serial peripheral interface (SPI) / Inter-integrated sound interface (I2S) . 26 3.19 High-definition multimedia interface (HDMI) - consumer electronics control (CEC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 3.20 Serial wire debug port (SW-DP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4 Pinouts and pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 5 Memory mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 6 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 6.1 Parameter conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 6.1.1 Minimum and maximum values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 6.1.2 Typical values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 6.1.3 Typical curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 6.1.4 Loading capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 6.1.5 Pin input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 6.1.6 Power supply scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 6.1.7 Current consumption measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 6.2 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 6.3 Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 6.3.1 General operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 6.3.2 Operating conditions at power-up / power-down . . . . . . . . . . . . . . . . . . 47 6.3.3 Embedded reset and power control block characteristics . . . . . . . . . . . 48 6.3.4 Embedded reference voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 6.3.5 Supply current characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 6.3.6 Wakeup time from low-power mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 6.3.7 External clock source characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 6.3.8 Internal clock source characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 6.3.9 PLL characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 6.3.10 Memory characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 6.3.11 EMC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 6.3.12 Electrical sensitivity characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 6.3.13 I/O current injection characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 DocID022265 Rev 6 3/121 4 Contents 7 STM32F051x4 STM32F051x6 STM32F051x8 6.3.14 I/O port characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 6.3.15 NRST pin characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 6.3.16 12-bit ADC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 6.3.17 DAC electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 6.3.18 Comparator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 6.3.19 Temperature sensor characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 6.3.20 VBAT monitoring characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 6.3.21 Timer characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 6.3.22 Communication interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 7.1 UFBGA64 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 7.2 LQFP64 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 7.3 LQFP48 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 7.4 UFQFPN48 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 7.5 WLCSP36 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 7.6 LQFP32 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 7.7 UFQFPN32 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 7.8 Thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 7.8.1 Reference document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 7.8.2 Selecting the product temperature range . . . . . . . . . . . . . . . . . . . . . . 112 8 Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 4/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 List of tables List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. Table 27. Table 28. Table 29. Table 30. Table 31. Table 32. Table 33. Table 34. Table 35. Table 36. Table 37. Table 38. Table 39. Table 40. Table 41. Table 42. Table 43. Table 44. Table 45. Table 46. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 STM32F051xx family device features and peripheral count . . . . . . . . . . . . . . . . . . . . . . . . 11 Temperature sensor calibration values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Internal voltage reference calibration values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Capacitive sensing GPIOs available on STM32F051xx devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Effective number of capacitive sensing channels on STM32F051xx . . . . . . . . . . . . . . . . . 20 Timer feature comparison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Comparison of I2C analog and digital filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 STM32F051xx I2C implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 STM32F051xx USART implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 STM32F051xx SPI/I2S implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Legend/abbreviations used in the pinout table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Pin definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Alternate functions selected through GPIOA_AFR registers for port A . . . . . . . . . . . . . . . 37 Alternate functions selected through GPIOB_AFR registers for port B . . . . . . . . . . . . . . . 38 STM32F051xx peripheral register boundary addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Voltage characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Current characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Thermal characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 General operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Operating conditions at power-up / power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Embedded reset and power control block characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . 48 Programmable voltage detector characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Embedded internal reference voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Typical and maximum current consumption from VDD at 3.6 V . . . . . . . . . . . . . . . . . . . . . 50 Typical and maximum current consumption from the VDDA supply . . . . . . . . . . . . . . . . . 51 Typical and maximum current consumption in Stop and Standby modes . . . . . . . . . . . . 52 Typical and maximum current consumption from the VBAT supply. . . . . . . . . . . . . . . . . . . 53 Typical current consumption, code executing from Flash memory, running from HSE 8 MHz crystal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Switching output I/O current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Peripheral current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Low-power mode wakeup timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 High-speed external user clock characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Low-speed external user clock characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 HSE oscillator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 LSE oscillator characteristics (fLSE = 32.768 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 HSI oscillator characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 HSI14 oscillator characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 LSI oscillator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 PLL characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Flash memory characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Flash memory endurance and data retention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 EMS characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 EMI characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 ESD absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Electrical sensitivities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 DocID022265 Rev 6 5/121 6 List of tables Table 47. Table 48. Table 49. Table 50. Table 51. Table 52. Table 53. Table 54. Table 55. Table 56. Table 57. Table 58. Table 59. Table 60. Table 61. Table 62. Table 63. Table 64. Table 65. Table 66. Table 67. Table 68. Table 69. Table 70. Table 71. Table 72. Table 73. Table 74. Table 75. Table 76. 6/121 STM32F051x4 STM32F051x6 STM32F051x8 I/O current injection susceptibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 I/O static characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Output voltage characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 I/O AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 NRST pin characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 ADC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 RAIN max for fADC = 14 MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 ADC accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 DAC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Comparator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 TS characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 VBAT monitoring characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 TIMx characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 IWDG min/max timeout period at 40 kHz (LSI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 WWDG min/max timeout value at 48 MHz (PCLK). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 I2C analog filter characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 SPI characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 I2S characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 UFBGA64 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 UFBGA64 recommended PCB design rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 LQFP64 package mechanical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 LQFP48 package mechanical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 UFQFPN48 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 WLCSP36 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 WLCSP36 recommended PCB design rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 LQFP32 package mechanical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 UFQFPN32 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Package thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 List of figures List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Figure 25. Figure 26. Figure 27. Figure 28. Figure 29. Figure 30. Figure 31. Figure 32. Figure 33. Figure 34. Figure 35. Figure 36. Figure 37. Figure 38. Figure 39. Figure 40. Figure 41. Figure 42. Figure 43. Figure 44. Figure 45. Figure 46. Figure 47. Figure 48. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Clock tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 LQFP64 package pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 UFBGA64 package pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 LQFP48 package pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 UFQFPN48 package pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 WLCSP36 package pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 LQFP32 package pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 UFQFPN32 package pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 STM32F051x8 memory map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Pin loading conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Pin input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Power supply scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Current consumption measurement scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 High-speed external clock source AC timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Low-speed external clock source AC timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Typical application with an 8 MHz crystal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Typical application with a 32.768 kHz crystal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 HSI oscillator accuracy characterization results for soldered parts . . . . . . . . . . . . . . . . . . 64 HSI14 oscillator accuracy characterization results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 TC and TTa I/O input characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Five volt tolerant (FT and FTf) I/O input characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 I/O AC characteristics definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Recommended NRST pin protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 ADC accuracy characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Typical connection diagram using the ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 12-bit buffered / non-buffered DAC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Maximum VREFINT scaler startup time from power down . . . . . . . . . . . . . . . . . . . . . . . . . . 83 SPI timing diagram - slave mode and CPHA = 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 SPI timing diagram - slave mode and CPHA = 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 SPI timing diagram - master mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 I2S slave timing diagram (Philips protocol). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 I2S master timing diagram (Philips protocol) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 UFBGA64 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Recommended footprint for UFBGA64 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 UFBGA64 package marking example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 LQFP64 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Recommended footprint for LQFP64 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 LQFP64 package marking example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 LQFP48 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Recommended footprint for LQFP48 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 LQFP48 package marking example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 UFQFPN48 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Recommended footprint for UFQFPN48 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 UFQFPN48 package marking example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 WLCSP36 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 Recommended pad footprint for WLCSP36 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 WLCSP36 package marking example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 DocID022265 Rev 6 7/121 8 List of figures Figure 49. Figure 50. Figure 51. Figure 52. Figure 53. Figure 54. Figure 55. 8/121 STM32F051x4 STM32F051x6 STM32F051x8 LQFP32 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Recommended footprint for LQFP32 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 LQFP32 package marking example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 UFQFPN32 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 Recommended footprint for UFQFPN32 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 UFQFPN32 package marking example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 LQFP64 PD max versus TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 1 Introduction Introduction This datasheet provides the ordering information and mechanical device characteristics of the STM32F051xx microcontrollers. This document should be read in conjunction with the STM32F0xxxx reference manual (RM0091). The reference manual is available from the STMicroelectronics website www.st.com. For information on the ARM(R) Cortex(R)-M0 core, please refer to the Cortex(R)-M0 Technical Reference Manual, available from the www.arm.com website. DocID022265 Rev 6 9/121 26 Description 2 STM32F051x4 STM32F051x6 STM32F051x8 Description The STM32F051xx microcontrollers incorporate the high-performance ARM(R) Cortex(R)-M0 32-bit RISC core operating at up to 48 MHz frequency, high-speed embedded memories (up to 64 Kbytes of Flash memory and 8 Kbytes of SRAM), and an extensive range of enhanced peripherals and I/Os. All devices offer standard communication interfaces (up to two I2Cs, up to two SPIs, one I2S, one HDMI CEC and up to two USARTs), one 12-bit ADC, one 12-bit DAC, six 16-bit timers, one 32-bit timer and an advanced-control PWM timer. The STM32F051xx microcontrollers operate in the -40 to +85 C and -40 to +105 C temperature ranges, from a 2.0 to 3.6 V power supply. A comprehensive set of powersaving modes allows the design of low-power applications. The STM32F051xx microcontrollers include devices in seven different packages ranging from 32 pins to 64 pins with a die form also available upon request. Depending on the device chosen, different sets of peripherals are included. These features make the STM32F051xx microcontrollers suitable for a wide range of applications such as application control and user interfaces, hand-held equipment, A/V receivers and digital TV, PC peripherals, gaming and GPS platforms, industrial applications, PLCs, inverters, printers, scanners, alarm systems, video intercoms and HVACs. 10/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Description Table 2. STM32F051xx family device features and peripheral count Peripheral STM32F051Kx Flash memory (Kbyte) 16 32 64 STM32F051T8 64 STM32F051Cx 16 SRAM (Kbyte) 32 1 (16-bit) General purpose 5 (16-bit) 1 (32-bit) Basic 1 (16-bit) SPI [I2S](1) 1 [1](2) 1 [1](2) 1 [1](2) 2C 1(3) 1(3) 1(3) Comm. interfaces I USART 16 32 1(4) 2 2 2 [1] 2 [1] 1(3) 2 1(4) CEC 2 2 1(4) 2 1 12-bit ADC (number of channels) 1 (10 ext. + 3 int.) 1 (16 ext. + 3 int.) 12-bit DAC (number of channels) 1 (1) Analog comparator 2 GPIOs 25 (on LQFP32) 27 (on UFQFPN32) 29 39 55 Capacitive sensing channels 13 (on LQFP32) 14 (on UFQFPN32) 14 17 18 Max. CPU frequency 48 MHz Operating voltage 2.0 to 3.6 V Operating temperature Ambient operating temperature: -40C to 85C / -40C to 105C Junction temperature: -40C to 105C / -40C to 125C Packages 64 8 Advanced control Timers 64 STM32F051Rx LQFP32 UFQFPN32 WLCSP36 LQFP48 UFQFPN48 LQFP64 UFBGA64 1. The SPI1 interface can be used either in SPI mode or in I2S audio mode. 2. SPI2 is not present. 3. I2C2 is not present. 4. USART2 is not present. DocID022265 Rev 6 11/121 26 Description STM32F051x4 STM32F051x6 STM32F051x8 Figure 1. Block diagram 32:(5 6HULDO:LUH 'HEXJ 2EO )ODVK PHPRU\ LQWHUIDFH 6:&/. 6:',2 DV$) 65$0 FRQWUROOHU 19,& %XVPDWUL[ &257(;0&38 I0$; 0+] 9'' )ODVK*3/ XSWR.% ELW #9'' 65$0 .% #9''$ +6, +6, 3//&/. /6, *3'0$ FKDQQHOV 9'' WR9 966 92/75(* 9WR9 325 5HVHW ,QW 6833/< 683(59,6,21 39' 5&0+] 5&0+] 1567 9''$ 966$ 9'' 3253'5 #9''$ #9'' 3// ;7$/26& 0+] 5&N+] 26&B,1 26&B287 ,QG:LQGRZ:'* 3$>@ *3,2SRUW$ 3%>@ *3,2SRUW% 3&>@ *3,2SRUW& 3' *3,2SRUW' 3)>@ 3)>@ *3,2SRUW) 3RZHU &RQWUROOHU 5(6(7 &/2&. &21752/ 9'' 9%$7 WR9 JURXSVRI FKDQQHOV 3$' $QDORJ VZLWFKHV $+%GHFRGHU #9%$7 026,6' 0,620&. 6&.&. 166:6DV$) 026,0,62 6&.166 DV$) 57& 7RXFK 6HQVLQJ &RQWUROOHU $+% FKDQQHOV FRPSOFKDQQHOV %5.(75LQSXWDV$) 7,0(5ELW FK(75DV$) 7,0(5 FK(75DV$) 7,0(5 FKDQQHODV$) 7,0(5 FKDQQHOV FRPSO%5.DV$) 7,0(5 FKDQQHO FRPSO%5.DV$) 7,0(5 FKDQQHO FRPSO%5.DV$) $3% (;7,7:.83 63,,6 :LQGRZ:'* ,5B287DV$) 63, '%*0&8 *3FRPSDUDWRU *3FRPSDUDWRU 86$57 5;7;&76576 &.DV$) 86$57 5;7;&76576 &.DV$) ,& 6&/6'$60%$ P$)0 DV$) ,& 6&/6'$ DV$) +'0,&(& &(&DV$) #9''$ 7HPS VHQVRU [ $'LQSXW ELW$'& ,) ,) 7,0(5 9''$ 966$ 3RZHUGRPDLQRIDQDORJEORFNV ELW'$& '$&B287DV$) #9''$ #9''$ 12/121 7$03(557& $/$50287 3:07,0(5 6<6&)*,) ,1387 ,1387 287387 DV$) %DFNXS UHJ 26&B,1 26&B287 57&LQWHUIDFH &5& 6<1& $) ;7$/N+] 6\VWHPDQGSHULSKHUDO FORFNV 9%$7 9'' 9''$ DocID022265 Rev 6 06Y9 STM32F051x4 STM32F051x6 STM32F051x8 3 Functional overview Functional overview Figure 1 shows the general block diagram of the STM32F051xx devices. 3.1 ARM(R)-Cortex(R)-M0 core The ARM(R) Cortex(R)-M0 is a generation of ARM 32-bit RISC processors for embedded systems. It has been developed to provide a low-cost platform that meets the needs of MCU implementation, with a reduced pin count and low-power consumption, while delivering outstanding computational performance and an advanced system response to interrupts. The ARM(R) Cortex(R)-M0 processors feature exceptional code-efficiency, delivering the high performance expected from an ARM core, with memory sizes usually associated with 8- and 16-bit devices. The STM32F051xx devices embed ARM core and are compatible with all ARM tools and software. 3.2 Memories The device has the following features: * 8 Kbytes of embedded SRAM accessed (read/write) at CPU clock speed with 0 wait states and featuring embedded parity checking with exception generation for fail-critical applications. * The non-volatile memory is divided into two arrays: - 16 to 64 Kbytes of embedded Flash memory for programs and data - Option bytes The option bytes are used to write-protect the memory (with 4 KB granularity) and/or readout-protect the whole memory with the following options: - Level 0: no readout protection - Level 1: memory readout protection, the Flash memory cannot be read from or written to if either debug features are connected or boot in RAM is selected (R) Level 2: chip readout protection, debug features (Cortex -M0 serial wire) and boot in RAM selection disabled - 3.3 Boot modes At startup, the boot pin and boot selector option bit are used to select one of the three boot options: * boot from User Flash memory * boot from System Memory * boot from embedded SRAM The boot loader is located in System Memory. It is used to reprogram the Flash memory by using USART on pins PA14/PA15 or PA9/PA10. DocID022265 Rev 6 13/121 26 Functional overview 3.4 STM32F051x4 STM32F051x6 STM32F051x8 Cyclic redundancy check calculation unit (CRC) The CRC (cyclic redundancy check) calculation unit is used to get a CRC code from a 32-bit data word and a CRC-32 (Ethernet) polynomial. Among other applications, CRC-based techniques are used to verify data transmission or storage integrity. In the scope of the EN/IEC 60335-1 standard, they offer a means of verifying the Flash memory integrity. The CRC calculation unit helps compute a signature of the software during runtime, to be compared with a reference signature generated at linktime and stored at a given memory location. 3.5 Power management 3.5.1 Power supply schemes * VDD = VDDIO1 = 2.0 to 3.6 V: external power supply for I/Os (VDDIO1) and the internal regulator. It is provided externally through VDD pins. * VDDA = from VDD to 3.6 V: external analog power supply for ADC, DAC, Reset blocks, RCs and PLL (minimum voltage to be applied to VDDA is 2.4 V when the ADC or DAC are used). It is provided externally through VDDA pin. The VDDA voltage level must be always greater or equal to the VDD voltage level and must be established first. * VBAT = 1.65 to 3.6 V: power supply for RTC, external clock 32 kHz oscillator and backup registers (through power switch) when VDD is not present. For more details on how to connect power pins, refer to Figure 13: Power supply scheme. 3.5.2 Power supply supervisors The device has integrated power-on reset (POR) and power-down reset (PDR) circuits. They are always active, and ensure proper operation above a threshold of 2 V. The device remains in reset mode when the monitored supply voltage is below a specified threshold, VPOR/PDR, without the need for an external reset circuit. * The POR monitors only the VDD supply voltage. During the startup phase it is required that VDDA should arrive first and be greater than or equal to VDD. * The PDR monitors both the VDD and VDDA supply voltages, however the VDDA power supply supervisor can be disabled (by programming a dedicated Option bit) to reduce the power consumption if the application design ensures that VDDA is higher than or equal to VDD. The device features an embedded programmable voltage detector (PVD) that monitors the VDD power supply and compares it to the VPVD threshold. An interrupt can be generated when VDD drops below the VPVD threshold and/or when VDD is higher than the VPVD threshold. The interrupt service routine can then generate a warning message and/or put the MCU into a safe state. The PVD is enabled by software. 3.5.3 Voltage regulator The regulator has two operating modes and it is always enabled after reset. 14/121 * Main (MR) is used in normal operating mode (Run). * Low power (LPR) can be used in Stop mode where the power demand is reduced. DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Functional overview In Standby mode, it is put in power down mode. In this mode, the regulator output is in high impedance and the kernel circuitry is powered down, inducing zero consumption (but the contents of the registers and SRAM are lost). 3.5.4 Low-power modes The STM32F051xx microcontrollers support three low-power modes to achieve the best compromise between low power consumption, short startup time and available wakeup sources: * Sleep mode In Sleep mode, only the CPU is stopped. All peripherals continue to operate and can wake up the CPU when an interrupt/event occurs. * Stop mode Stop mode achieves very low power consumption while retaining the content of SRAM and registers. All clocks in the 1.8 V domain are stopped, the PLL, the HSI RC and the HSE crystal oscillators are disabled. The voltage regulator can also be put either in normal or in low power mode. The device can be woken up from Stop mode by any of the EXTI lines. The EXTI line source can be one of the 16 external lines, the PVD output, RTC, I2C1, USART1,, COMPx or the CEC. The CEC, USART1 and I2C1 peripherals can be configured to enable the HSI RC oscillator so as to get clock for processing incoming data. If this is used when the voltage regulator is put in low power mode, the regulator is first switched to normal mode before the clock is provided to the given peripheral. * Standby mode The Standby mode is used to achieve the lowest power consumption. The internal voltage regulator is switched off so that the entire 1.8 V domain is powered off. The PLL, the HSI RC and the HSE crystal oscillators are also switched off. After entering Standby mode, SRAM and register contents are lost except for registers in the RTC domain and Standby circuitry. The device exits Standby mode when an external reset (NRST pin), an IWDG reset, a rising edge on the WKUP pins, or an RTC event occurs. Note: The RTC, the IWDG, and the corresponding clock sources are not stopped by entering Stop or Standby mode. 3.6 Clocks and startup System clock selection is performed on startup, however the internal RC 8 MHz oscillator is selected as default CPU clock on reset. An external 4-32 MHz clock can be selected, in which case it is monitored for failure. If failure is detected, the system automatically switches back to the internal RC oscillator. A software interrupt is generated if enabled. Similarly, full interrupt management of the PLL clock entry is available when necessary (for example on failure of an indirectly used external crystal, resonator or oscillator). Several prescalers allow the application to configure the frequency of the AHB and the APB domains. The maximum frequency of the AHB and the APB domains is 48 MHz. DocID022265 Rev 6 15/121 26 Functional overview STM32F051x4 STM32F051x6 STM32F051x8 Figure 2. Clock tree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eneral-purpose inputs/outputs (GPIOs) Each of the GPIO pins can be configured by software as output (push-pull or open-drain), as input (with or without pull-up or pull-down) or as peripheral alternate function. Most of the GPIO pins are shared with digital or analog alternate functions. 16/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Functional overview The I/O configuration can be locked if needed following a specific sequence in order to avoid spurious writing to the I/Os registers. 3.8 Direct memory access controller (DMA) The 5-channel general-purpose DMAs manage memory-to-memory, peripheral-to-memory and memory-to-peripheral transfers. The DMA supports circular buffer management, removing the need for user code intervention when the controller reaches the end of the buffer. Each channel is connected to dedicated hardware DMA requests, with support for software trigger on each channel. Configuration is made by software and transfer sizes between source and destination are independent. DMA can be used with the main peripherals: SPIx, I2Sx, I2Cx, USARTx, all TIMx timers (except TIM14), DAC and ADC. 3.9 Interrupts and events 3.9.1 Nested vectored interrupt controller (NVIC) The STM32F0xx family embeds a nested vectored interrupt controller able to handle up to (R) 32 maskable interrupt channels (not including the 16 interrupt lines of Cortex -M0) and 4 priority levels. * Closely coupled NVIC gives low latency interrupt processing * Interrupt entry vector table address passed directly to the core * Closely coupled NVIC core interface * Allows early processing of interrupts * Processing of late arriving higher priority interrupts * Support for tail-chaining * Processor state automatically saved * Interrupt entry restored on interrupt exit with no instruction overhead This hardware block provides flexible interrupt management features with minimal interrupt latency. 3.9.2 Extended interrupt/event controller (EXTI) The extended interrupt/event controller consists of 24 edge detector lines used to generate interrupt/event requests and wake-up the system. Each line can be independently configured to select the trigger event (rising edge, falling edge, both) and can be masked independently. A pending register maintains the status of the interrupt requests. The EXTI can detect an external line with a pulse width shorter than the internal clock period. Up to 55 GPIOs can be connected to the 16 external interrupt lines. 3.10 Analog-to-digital converter (ADC) The 12-bit analog-to-digital converter has up to 16 external and 3 internal (temperature DocID022265 Rev 6 17/121 26 Functional overview STM32F051x4 STM32F051x6 STM32F051x8 sensor, voltage reference, VBAT voltage measurement) channels and performs conversions in single-shot or scan modes. In scan mode, automatic conversion is performed on a selected group of analog inputs. The ADC can be served by the DMA controller. An analog watchdog feature allows very precise monitoring of the converted voltage of one, some or all selected channels. An interrupt is generated when the converted voltage is outside the programmed thresholds. 3.10.1 Temperature sensor The temperature sensor (TS) generates a voltage VSENSE that varies linearly with temperature. The temperature sensor is internally connected to the ADC_IN16 input channel which is used to convert the sensor output voltage into a digital value. The sensor provides good linearity but it has to be calibrated to obtain good overall accuracy of the temperature measurement. As the offset of the temperature sensor varies from chip to chip due to process variation, the uncalibrated internal temperature sensor is suitable for applications that detect temperature changes only. To improve the accuracy of the temperature sensor measurement, each device is individually factory-calibrated by ST. The temperature sensor factory calibration data are stored by ST in the system memory area, accessible in read-only mode. Table 3. Temperature sensor calibration values 3.10.2 Calibration value name Description Memory address TS_CAL1 TS ADC raw data acquired at a temperature of 30 C ( 5 C), VDDA= 3.3 V ( 10 mV) 0x1FFF F7B8 - 0x1FFF F7B9 TS_CAL2 TS ADC raw data acquired at a temperature of 110 C ( 5 C), VDDA= 3.3 V ( 10 mV) 0x1FFF F7C2 - 0x1FFF F7C3 Internal voltage reference (VREFINT) The internal voltage reference (VREFINT) provides a stable (bandgap) voltage output for the ADC and comparators. VREFINT is internally connected to the ADC_IN17 input channel. The precise voltage of VREFINT is individually measured for each part by ST during production test and stored in the system memory area. It is accessible in read-only mode. Table 4. Internal voltage reference calibration values 18/121 Calibration value name Description Memory address VREFINT_CAL Raw data acquired at a temperature of 30 C ( 5 C), VDDA= 3.3 V ( 10 mV) 0x1FFF F7BA - 0x1FFF F7BB DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 3.10.3 Functional overview VBAT battery voltage monitoring This embedded hardware feature allows the application to measure the VBAT battery voltage using the internal ADC channel ADC_IN18. As the VBAT voltage may be higher than VDDA, and thus outside the ADC input range, the VBAT pin is internally connected to a bridge divider by 2. As a consequence, the converted digital value is half the VBAT voltage. 3.11 Digital-to-analog converter (DAC) The 12-bit buffered DAC channels can be used to convert digital signals into analog voltage signal outputs. The chosen design structure is composed of integrated resistor strings and an amplifier in non-inverting configuration. This digital Interface supports the following features: * Left or right data alignment in 12-bit mode * Synchronized update capability * DMA capability * External triggers for conversion Five DAC trigger inputs are used in the device. The DAC is triggered through the timer trigger outputs and the DAC interface is generating its own DMA requests. 3.12 Comparators (COMP) The device embeds two fast rail-to-rail low-power comparators with programmable reference voltage (internal or external), hysteresis and speed (low speed for low power) and with selectable output polarity. The reference voltage can be one of the following: * External I/O * DAC output pins * Internal reference voltage or submultiple (1/4, 1/2, 3/4).Refer to Table 24: Embedded internal reference voltage for the value and precision of the internal reference voltage. Both comparators can wake up from STOP mode, generate interrupts and breaks for the timers and can be also combined into a window comparator. 3.13 Touch sensing controller (TSC) The STM32F051xx devices provide a simple solution for adding capacitive sensing functionality to any application. These devices offer up to 18 capacitive sensing channels distributed over 6 analog I/O groups. Capacitive sensing technology is able to detect the presence of a finger near a sensor which is protected from direct touch by a dielectric (glass, plastic...). The capacitive variation introduced by the finger (or any conductive object) is measured using a proven implementation based on a surface charge transfer acquisition principle. It consists in charging the sensor capacitance and then transferring a part of the accumulated charges into a sampling capacitor until the voltage across this capacitor has reached a specific threshold. To limit the CPU bandwidth usage, this acquisition is directly managed by the DocID022265 Rev 6 19/121 26 Functional overview STM32F051x4 STM32F051x6 STM32F051x8 hardware touch sensing controller and only requires few external components to operate. For operation, one capacitive sensing GPIO in each group is connected to an external capacitor and cannot be used as effective touch sensing channel. The touch sensing controller is fully supported by the STMTouch touch sensing firmware library, which is free to use and allows touch sensing functionality to be implemented reliably in the end application. Table 5. Capacitive sensing GPIOs available on STM32F051xx devices Group 1 2 3 Capacitive sensing signal name Pin name TSC_G1_IO1 PA0 TSC_G1_IO2 PA1 TSC_G1_IO3 PA2 TSC_G1_IO4 Capacitive sensing signal name Pin name TSC_G4_IO1 PA9 TSC_G4_IO2 PA10 TSC_G4_IO3 PA11 PA3 TSC_G4_IO4 PA12 TSC_G2_IO1 PA4 TSC_G5_IO1 PB3 TSC_G2_IO2 PA5 TSC_G5_IO2 PB4 TSC_G2_IO3 PA6 TSC_G5_IO3 PB6 TSC_G2_IO4 PA7 TSC_G5_IO4 PB7 TSC_G3_IO1 PC5 TSC_G6_IO1 PB11 TSC_G3_IO2 PB0 TSC_G6_IO2 PB12 TSC_G3_IO3 PB1 TSC_G6_IO3 PB13 TSC_G3_IO4 PB2 TSC_G6_IO4 PB14 Group 4 5 6 Table 6. Effective number of capacitive sensing channels on STM32F051xx Number of capacitive sensing channels Analog I/O group STM32F051KxU STM32F051KxT (UFQFPN32) (LQFP32) STM32F051Rx STM32F051Cx STM32F051Tx G1 3 3 3 3 3 G2 3 3 3 3 3 G3 3 2 2 2 1 G4 3 3 3 3 3 G5 3 3 3 3 3 G6 3 3 0 0 0 Number of capacitive sensing channels 18 17 14 14 13 20/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 3.14 Functional overview Timers and watchdogs The STM32F051xx devices include up to six general-purpose timers, one basic timer and an advanced control timer. Table 7 compares the features of the different timers. Table 7. Timer feature comparison Timer type Timer Counter resolution Counter type Prescaler factor DMA request generation Advanced control TIM1 16-bit Up, down, up/down integer from 1 to 65536 Yes 4 3 TIM2 32-bit Up, down, up/down integer from 1 to 65536 Yes 4 - TIM3 16-bit Up, down, up/down integer from 1 to 65536 Yes 4 - TIM14 16-bit Up integer from 1 to 65536 No 1 - TIM15 16-bit Up integer from 1 to 65536 Yes 2 1 TIM16 TIM17 16-bit Up integer from 1 to 65536 Yes 1 1 TIM6 16-bit Up integer from 1 to 65536 Yes - - General purpose Basic 3.14.1 Capture/compare Complementary channels outputs Advanced-control timer (TIM1) The advanced-control timer (TIM1) can be seen as a three-phase PWM multiplexed on six channels. It has complementary PWM outputs with programmable inserted dead times. It can also be seen as a complete general-purpose timer. The four independent channels can be used for: * input capture * output compare * PWM generation (edge or center-aligned modes) * one-pulse mode output If configured as a standard 16-bit timer, it has the same features as the TIMx timer. If configured as the 16-bit PWM generator, it has full modulation capability (0-100%). The counter can be frozen in debug mode. Many features are shared with those of the standard timers which have the same architecture. The advanced control timer can therefore work together with the other timers via the Timer Link feature for synchronization or event chaining. DocID022265 Rev 6 21/121 26 Functional overview 3.14.2 STM32F051x4 STM32F051x6 STM32F051x8 General-purpose timers (TIM2, 3, 14, 15, 16, 17) There are six synchronizable general-purpose timers embedded in the STM32F051xx devices (see Table 7 for differences). Each general-purpose timer can be used to generate PWM outputs, or as simple time base. TIM2, TIM3 STM32F051xx devices feature two synchronizable 4-channel general-purpose timers. TIM2 is based on a 32-bit auto-reload up/downcounter and a 16-bit prescaler. TIM3 is based on a 16-bit auto-reload up/downcounter and a 16-bit prescaler. They feature 4 independent channels each for input capture/output compare, PWM or one-pulse mode output. This gives up to 12 input captures/output compares/PWMs on the largest packages. The TIM2 and TIM3 general-purpose timers can work together or with the TIM1 advancedcontrol timer via the Timer Link feature for synchronization or event chaining. TIM2 and TIM3 both have independent DMA request generation. These timers are capable of handling quadrature (incremental) encoder signals and the digital outputs from 1 to 3 hall-effect sensors. Their counters can be frozen in debug mode. TIM14 This timer is based on a 16-bit auto-reload upcounter and a 16-bit prescaler. TIM14 features one single channel for input capture/output compare, PWM or one-pulse mode output. Its counter can be frozen in debug mode. TIM15, TIM16 and TIM17 These timers are based on a 16-bit auto-reload upcounter and a 16-bit prescaler. TIM15 has two independent channels, whereas TIM16 and TIM17 feature one single channel for input capture/output compare, PWM or one-pulse mode output. The TIM15, TIM16 and TIM17 timers can work together, and TIM15 can also operate withTIM1 via the Timer Link feature for synchronization or event chaining. TIM15 can be synchronized with TIM16 and TIM17. TIM15, TIM16 and TIM17 have a complementary output with dead-time generation and independent DMA request generation. Their counters can be frozen in debug mode. 3.14.3 Basic timer TIM6 This timer is mainly used for DAC trigger generation. It can also be used as a generic 16-bit time base. 3.14.4 Independent watchdog (IWDG) The independent watchdog is based on an 8-bit prescaler and 12-bit downcounter with user-defined refresh window. It is clocked from an independent 40 kHz internal RC and as it operates independently from the main clock, it can operate in Stop and Standby modes. It 22/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Functional overview can be used either as a watchdog to reset the device when a problem occurs, or as a free running timer for application timeout management. It is hardware or software configurable through the option bytes. The counter can be frozen in debug mode. 3.14.5 System window watchdog (WWDG) The system window watchdog is based on a 7-bit downcounter that can be set as free running. It can be used as a watchdog to reset the device when a problem occurs. It is clocked from the APB clock (PCLK). It has an early warning interrupt capability and the counter can be frozen in debug mode. 3.14.6 SysTick timer This timer is dedicated to real-time operating systems, but could also be used as a standard down counter. It features: 3.15 * a 24-bit down counter * autoreload capability * maskable system interrupt generation when the counter reaches 0 * programmable clock source (HCLK or HCLK/8) Real-time clock (RTC) and backup registers The RTC and the five backup registers are supplied through a switch that takes power either on VDD supply when present or through the VBAT pin. The backup registers are five 32-bit registers used to store 20 bytes of user application data when VDD power is not present. They are not reset by a system or power reset, or at wake up from Standby mode. The RTC is an independent BCD timer/counter. Its main features are the following: * calendar with subseconds, seconds, minutes, hours (12 or 24 format), week day, date, month, year, in BCD (binary-coded decimal) format * automatic correction for 28, 29 (leap year), 30, and 31 day of the month * programmable alarm with wake up from Stop and Standby mode capability * on-the-fly correction from 1 to 32767 RTC clock pulses. This can be used to synchronize the RTC with a master clock * digital calibration circuit with 1 ppm resolution, to compensate for quartz crystal inaccuracy * two anti-tamper detection pins with programmable filter. The MCU can be woken up from Stop and Standby modes on tamper event detection * timestamp feature which can be used to save the calendar content. This function can be triggered by an event on the timestamp pin, or by a tamper event. The MCU can be woken up from Stop and Standby modes on timestamp event detection * reference clock detection: a more precise second source clock (50 or 60 Hz) can be used to enhance the calendar precision DocID022265 Rev 6 23/121 26 Functional overview STM32F051x4 STM32F051x6 STM32F051x8 The RTC clock sources can be: 3.16 * a 32.768 kHz external crystal * a resonator or oscillator * the internal low-power RC oscillator (typical frequency of 40 kHz) * the high-speed external clock divided by 32 Inter-integrated circuit interface (I2C) Up to two I2C interfaces (I2C1 and I2C2) can operate in multimaster or slave modes. Both can support Standard mode (up to 100 kbit/s) and Fast mode (up to 400 kbit/s) and, I2C1 also supports Fast Mode Plus (up to 1 Mbit/s) with 20 mA output drive. Both support 7-bit and 10-bit addressing modes, multiple 7-bit slave addresses (two addresses, one with configurable mask). They also include programmable analog and digital noise filters. Table 8. Comparison of I2C analog and digital filters Aspect Analog filter Digital filter Pulse width of suppressed spikes 50 ns Programmable length from 1 to 15 I2Cx peripheral clocks Benefits Available in Stop mode Drawbacks Variations depending on temperature, voltage, process -Extra filtering capability vs. standard requirements -Stable length Wakeup from Stop on address match is not available when digital filter is enabled. In addition, I2C1 provides hardware support for SMBUS 2.0 and PMBUS 1.1: ARP capability, Host notify protocol, hardware CRC (PEC) generation/verification, timeouts verifications and ALERT protocol management. I2C1 also has a clock domain independent from the CPU clock, allowing the I2C1 to wake up the MCU from Stop mode on address match. The I2C peripherals can be served by the DMA controller. Refer to Table 9 for the differences between I2C1 and I2C2. Table 9. STM32F051xx I2C implementation I2C features(1) 24/121 I2C1 I2C2 7-bit addressing mode X X 10-bit addressing mode X X Standard mode (up to 100 kbit/s) X X Fast mode (up to 400 kbit/s) X X Fast Mode Plus (up to 1 Mbit/s) with 20 mA output drive I/Os X - Independent clock X - DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Functional overview Table 9. STM32F051xx I2C implementation (continued) I2C features(1) I2C1 I2C2 SMBus X - Wakeup from STOP X - 1. X = supported. 3.17 Universal synchronous/asynchronous receiver/transmitter (USART) The device embeds up to two universal synchronous/asynchronous receivers/transmitters (USART1, USART2) which communicate at speeds of up to 6 Mbit/s. They provide hardware management of the CTS, RTS and RS485 DE signals, multiprocessor communication mode, master synchronous communication and single-wire half-duplex communication mode. USART1 supports also SmartCard communication (ISO 7816), IrDA SIR ENDEC, LIN Master/Slave capability and auto baud rate feature, and has a clock domain independent of the CPU clock, allowing to wake up the MCU from Stop mode. The USART interfaces can be served by the DMA controller. Table 10. STM32F051xx USART implementation USART modes/features(1) USART1 USART2 Hardware flow control for modem X X Continuous communication using DMA X X Multiprocessor communication X X Synchronous mode X X Smartcard mode X - Single-wire half-duplex communication X X IrDA SIR ENDEC block X - LIN mode X - Dual clock domain and wakeup from Stop mode X - Receiver timeout interrupt X - Modbus communication X - Auto baud rate detection X - Driver Enable X X 1. X = supported. DocID022265 Rev 6 25/121 26 Functional overview 3.18 STM32F051x4 STM32F051x6 STM32F051x8 Serial peripheral interface (SPI) / Inter-integrated sound interface (I2S) Up to two SPIs are able to communicate up to 18 Mbit/s in slave and master modes in fullduplex and half-duplex communication modes. The 3-bit prescaler gives 8 master mode frequencies and the frame size is configurable from 4 bits to 16 bits. One standard I2S interface (multiplexed with SPI1) supporting four different audio standards can operate as master or slave at half-duplex communication mode. It can be configured to transfer 16 and 24 or 32 bits with 16-bit or 32-bit data resolution and synchronized by a specific signal. Audio sampling frequency from 8 kHz up to 192 kHz can be set by an 8-bit programmable linear prescaler. When operating in master mode, it can output a clock for an external audio component at 256 times the sampling frequency. Table 11. STM32F051xx SPI/I2S implementation SPI features(1) SPI1 SPI2 Hardware CRC calculation X X Rx/Tx FIFO X X NSS pulse mode X X I2S X - X X mode TI mode 1. X = supported. 3.19 High-definition multimedia interface (HDMI) - consumer electronics control (CEC) The device embeds a HDMI-CEC controller that provides hardware support for the Consumer Electronics Control (CEC) protocol (Supplement 1 to the HDMI standard). This protocol provides high-level control functions between all audiovisual products in an environment. It is specified to operate at low speeds with minimum processing and memory overhead. It has a clock domain independent from the CPU clock, allowing the HDMI_CEC controller to wakeup the MCU from Stop mode on data reception. 3.20 Serial wire debug port (SW-DP) An ARM SW-DP interface is provided to allow a serial wire debugging tool to be connected to the MCU. 26/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Pinouts and pin descriptions /4)3 3) 3) 3$ 3$ 3$ 3$ 3$ 3$ 3& 3& 3& 3& 3% 3% 3% 3% 9%$7 3& 3&26&B,1 3&26&B287 3)26&B,1 3)26&B287 1567 3& 3& 3& 3& 966$ 9''$ 3$ 3$ 3$ 7RSYLHZ 9'' 966 3% 3% %227 3% 3% 3% 3% 3% 3' 3& 3& 3& 3$ 3$ Figure 3. LQFP64 package pinout 3$ 3) 3) 3$ 3$ 3$ 3$ 3& 3& 3% 3% 3% 3% 3% 966 9'' 4 Pinouts and pin descriptions 06Y9 DocID022265 Rev 6 27/121 36 Pinouts and pin descriptions STM32F051x4 STM32F051x6 STM32F051x8 Figure 4. UFBGA64 package pinout 7RSYLHZ $ 3& 26&B ,1 3& 3% 3% 3% 3$ 3$ 3$ % 3& 26&B 287 9%$7 3% %227 3' 3& 3& 3$ & 3) 26&B ,1 3) 3% 3% 3& 3$ 3$ 3$ ' 3) 26&B 287 3) 3% 966 966 3) 3$ 3& ( 1567 3& 3& 9'' 9'' 3) 3& 3& ) 966$ 3& 3$ 3$ 3% 3& 3% 3% * 3& 3$ 3$ 3$ 3% 3% 3% 3% + 9''$ 3$ 3$ 3$ 3& 3& 3% 3% 8)%*$ 06Y9 /4)3 3) 3) 3$ 3$ 3$ 3$ 3$ 3$ 3% 3% 3% 3% 3$ 3$ 3$ 3$ 3$ 3% 3% 3% 3% 3% 966 9'' 9%$7 3& 3&26&B,1 3&26&B287 3)26&B,1 3)26&B287 1567 966$ 9''$ 3$ 3$ 3$ 7RSYLHZ 9'' 966 3% 3% %227 3% 3% 3% 3% 3% 3$ 3$ Figure 5. LQFP48 package pinout 06Y9 28/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Pinouts and pin descriptions Figure 6. UFQFPN48 package pinout 9'' 966 3% 3% %227 3% 3% 3% 3% 3% 3$ 3$ 7RSYLHZ 9%$7 3) 3& 3) 3&26&B,1 3$ 3&26&B287 3$ 3)26&B,1 3$ 3)26&B287 3$ 1567 3$ 966$ 3$ 9''$ 3% 3$ 3% 3$ 3% 3$ 3% 8)4)31 3$ 3$ 3$ 3$ 3$ 3% 3% 3% 3% 3% 966 9'' ([SRVHGSDG 06Y9 Figure 7. WLCSP36 package pinout 7RSYLHZ $ 3$ 3$ 3% 3% 9'' 3& % 3$ 3$ 3% %227 3& 3) 26&B 26&B ,1 ,1 & 3$ 3$ 3$ 3% 3) 3& 26&B 26&B 287 287 ' 3$ 3% 3$ 3$ 1567 966 ( 9'' 3$ 3$ 3$ 9''$ 3% ) 966 3% 3% 3$ 3$ 3$ :/&63 06Y9 1. The above figure shows the package in top view, changing from bottom view in the previous document versions. DocID022265 Rev 6 29/121 36 Pinouts and pin descriptions STM32F051x4 STM32F051x6 STM32F051x8 /4)3 3$ 3$ 3$ 3$ 3$ 3$ 3$ 9'' 3$ 3$ 3$ 3$ 3$ 3% 3% 966 9'' 3)26&B,1 3)26&B287 1567 9''$ 3$ 3$ 3$ 7RSYLHZ 966 %227 3% 3% 3% 3% 3% 3$ Figure 8. LQFP32 package pinout 06Y9 Figure 9. UFQFPN32 package pinout 8)4)31 ([SRVHGSDG 3$ 3$ 3$ 3$ 3$ 3$ 3$ 9'' 9'' 3)26&B,1 3)26&B287 1567 9''$ 3$ 3$ 3$ 3% %227 3% 3% 3% 3% 3% 3$ 7RSYLHZ 3$ 3$ 3$ 3$ 3$ 3% 3% 3% 966 06Y9 30/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Pinouts and pin descriptions Table 12. Legend/abbreviations used in the pinout table Name Abbreviation Definition Unless otherwise specified in brackets below the pin name, the pin function during and after reset is the same as the actual pin name Pin name Pin type I/O structure S Supply pin I Input only pin I/O Input / output pin FT 5 V tolerant I/O FTf 5 V tolerant I/O, FM+ capable TTa 3.3 V tolerant I/O directly connected to ADC TC Standard 3.3 V I/O B Dedicated BOOT0 pin RST Unless otherwise specified by a note, all I/Os are set as floating inputs during and after reset. Notes Pin functions Bidirectional reset pin with embedded weak pull-up resistor Alternate functions Functions selected through GPIOx_AFR registers Additional functions Functions directly selected/enabled through peripheral registers Table 13. Pin definitions LQFP32 UFQFPN32 B2 1 - - - VBAT Notes WLCSP36 1 I/O structure LQFP48/UFQFPN48 Pin name (function upon reset) Pin type UFBGA64 Pin functions LQFP64 Pin number S - - - RTC_TAMP1, RTC_TS, RTC_OUT, WKUP2 Alternate functions Additional functions Backup power supply 2 A2 2 A6 - - PC13 I/O TC (1)(2) 3 A1 3 B6 - - PC14-OSC32_IN (PC14) I/O TC (1)(2) - OSC32_IN 4 B1 4 C6 - - PC15-OSC32_OUT I/O (PC15) TC (1)(2) - OSC32_OUT 5 C1 5 B5 2 2 PF0-OSC_IN (PF0) I/O FT - - OSC_IN 6 D1 6 C5 3 3 PF1-OSC_OUT (PF1) I/O FT - - OSC_OUT DocID022265 Rev 6 31/121 36 Pinouts and pin descriptions STM32F051x4 STM32F051x6 STM32F051x8 Table 13. Pin definitions (continued) LQFP32 UFQFPN32 E1 7 D5 4 4 NRST 8 E3 - - - - 9 E2 - - - 10 F2 - - 11 G1 - 12 F1 13 H1 16 H2 F3 Alternate functions Additional functions Device reset input / internal reset output (active low) I/O RST - PC0 I/O TTa - EVENTOUT ADC_IN10 - PC1 I/O TTa - EVENTOUT ADC_IN11 - - PC2 I/O TTa - EVENTOUT ADC_IN12 - - - PC3 I/O TTa - EVENTOUT ADC_IN13 8 D6 16 0 VSSA S - (3) Analog ground 9 E5 5 5 VDDA S - - Analog power supply 14 G2 10 15 Notes WLCSP36 7 I/O structure LQFP48/UFQFPN48 Pin name (function upon reset) Pin type UFBGA64 Pin functions LQFP64 Pin number 11 12 17 G3 13 F6 D4 E4 6 7 8 6 7 8 PA0 PA1 PA2 I/O I/O I/O TTa TTa TTa - USART2_CTS, TIM2_CH1_ETR, COMP1_OUT, TSC_G1_IO1 ADC_IN0, COMP1_INM6, RTC_TAMP2, WKUP1 - USART2_RTS, TIM2_CH2, TSC_G1_IO2, EVENTOUT ADC_IN1, COMP1_INP - USART2_TX, TIM2_CH3, TIM15_CH1, COMP2_OUT, TSC_G1_IO3 ADC_IN2, COMP2_INM6 ADC_IN3, COMP2_INP F5 9 9 PA3 I/O TTa - USART2_RX, TIM2_CH4, TIM15_CH2, TSC_G1_IO4 18 C2 - - - - PF4 I/O FT - EVENTOUT - 19 D2 - - - - PF5 I/O FT - EVENTOUT - - SPI1_NSS, I2S1_WS, USART2_CK, TIM14_CH1, TSC_G2_IO1 ADC_IN4, COMP1_INM4, COMP2_INM4, DAC_OUT1 - SPI1_SCK, I2S1_CK, CEC, TIM2_CH1_ETR, TSC_G2_IO2 ADC_IN5, COMP1_INM5, COMP2_INM5 20 21 H3 F4 32/121 14 15 C3 D3 10 11 10 11 PA4 PA5 I/O I/O TTa TTa DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Pinouts and pin descriptions Table 13. Pin definitions (continued) 22 G4 16 E3 12 12 PA6 I/O TTa Notes I/O structure Pin name (function upon reset) Pin type UFQFPN32 Pin functions LQFP32 WLCSP36 LQFP48/UFQFPN48 UFBGA64 LQFP64 Pin number Alternate functions Additional functions - SPI1_MISO, I2S1_MCK, TIM3_CH1, TIM1_BKIN, TIM16_CH1, COMP1_OUT, TSC_G2_IO3, EVENTOUT ADC_IN6 ADC_IN7 23 H4 17 F4 13 13 PA7 I/O TTa - SPI1_MOSI, I2S1_SD, TIM3_CH2, TIM14_CH1, TIM1_CH1N, TIM17_CH1, COMP2_OUT, TSC_G2_IO4, EVENTOUT 24 H5 - - - - PC4 I/O TTa - EVENTOUT ADC_IN14 25 H6 - - - - PC5 I/O TTa - TSC_G3_IO1 ADC_IN15 - TIM3_CH3, TIM1_CH2N, TSC_G3_IO2, EVENTOUT ADC_IN8 ADC_IN9 26 F5 18 F3 14 14 PB0 I/O TTa 27 G5 19 F2 15 15 PB1 I/O TTa - TIM3_CH4, TIM14_CH1, TIM1_CH3N, TSC_G3_IO3 28 G6 20 D2 - 16 PB2 I/O FT (4) TSC_G3_IO4 - FT (5) I2C2_SCL, CEC, TIM2_CH3, TSC_SYNC - I2C2_SDA, TIM2_CH4, TSC_G6_IO1, EVENTOUT - 29 G7 21 - - - PB10 I/O 30 H7 22 - - - PB11 I/O FT (5) 31 D4 23 F1 16 0 VSS S - - Ground 32 E4 24 E1 17 17 VDD S - - Digital power supply DocID022265 Rev 6 33/121 36 Pinouts and pin descriptions STM32F051x4 STM32F051x6 STM32F051x8 Table 13. Pin definitions (continued) I/O FT 34 G8 26 - - - PB13 I/O FT (5) SPI2_SCK, TIM1_CH1N, TSC_G6_IO3 - FT (5) SPI2_MISO, TIM1_CH2N, TIM15_CH1, TSC_G6_IO4 - RTC_REFIN 35 F8 27 - - - Pin name (function upon reset) PB14 Pin type PB12 UFQFPN32 - LQFP32 - H8 WLCSP36 - 33 UFBGA64 25 (5) LQFP64 Notes Pin functions I/O structure LQFP48/UFQFPN48 Pin number I/O Alternate functions Additional functions SPI2_NSS, TIM1_BKIN, TSC_G6_IO2, EVENTOUT - 36 F7 28 - - - PB15 I/O FT (5) SPI2_MOSI, TIM1_CH3N, TIM15_CH1N, TIM15_CH2 37 F6 - - - - PC6 I/O FT - TIM3_CH1 - 38 E7 - - - - PC7 I/O FT - TIM3_CH2 - 39 E8 - - - - PC8 I/O FT - TIM3_CH3 - 40 D8 - - - - PC9 I/O FT - TIM3_CH4 - - USART1_CK, TIM1_CH1, EVENTOUT, MCO - - USART1_TX, TIM1_CH2, TIM15_BKIN, TSC_G4_IO1 - - USART1_RX, TIM1_CH3, TIM17_BKIN, TSC_G4_IO2 - - USART1_CTS, TIM1_CH4, COMP1_OUT, TSC_G4_IO3, EVENTOUT - 41 42 43 44 D7 C7 C6 C8 34/121 29 30 31 32 E2 D1 C1 C2 18 19 20 21 18 19 20 21 PA8 PA9 PA10 PA11 I/O I/O I/O I/O FT FT FT FT DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Pinouts and pin descriptions Table 13. Pin definitions (continued) Notes I/O structure Pin name (function upon reset) Pin type UFQFPN32 Pin functions LQFP32 WLCSP36 LQFP48/UFQFPN48 UFBGA64 LQFP64 Pin number Alternate functions Additional functions - 45 B8 33 A1 22 22 PA12 I/O FT - USART1_RTS, TIM1_ETR, COMP2_OUT, TSC_G4_IO4, EVENTOUT 46 A8 34 B1 23 23 PA13 (SWDIO) I/O FT (6) IR_OUT, SWDIO - 47 D6 35 - - - PF6 I/O FT - I2C2_SCL - 48 E6 36 - - - PF7 I/O FT - I2C2_SDA - 49 A7 37 B2 24 24 PA14 (SWCLK) I/O FT (6) USART2_TX, SWCLK - SPI1_NSS, I2S1_WS, USART2_RX, TIM2_CH1_ETR, EVENTOUT - 50 A6 38 A2 25 25 PA15 I/O FT - 51 B7 - - - - PC10 I/O FT - - 52 B6 - - - - PC11 I/O FT - - 53 C5 - - - - PC12 I/O FT - - 54 B5 - - - - PD2 I/O FT - TIM3_ETR - - SPI1_SCK, I2S1_CK, TIM2_CH2, TSC_G5_IO1, EVENTOUT - - SPI1_MISO, I2S1_MCK, TIM3_CH1, TSC_G5_IO2, EVENTOUT - - SPI1_MOSI, I2S1_SD, I2C1_SMBA, TIM16_BKIN, TIM3_CH2 - 55 56 57 A5 A4 C4 39 40 41 B3 A3 E6 26 27 28 26 27 28 PB3 PB4 PB5 I/O I/O I/O FT FT FT DocID022265 Rev 6 35/121 36 Pinouts and pin descriptions STM32F051x4 STM32F051x6 STM32F051x8 Table 13. Pin definitions (continued) 58 D3 42 C4 29 29 PB6 I/O FTf Notes I/O structure Pin name (function upon reset) Pin type UFQFPN32 Pin functions LQFP32 WLCSP36 LQFP48/UFQFPN48 UFBGA64 LQFP64 Pin number Alternate functions Additional functions - I2C1_SCL, USART1_TX, TIM16_CH1N, TSC_G5_IO3 - I2C1_SDA, USART1_RX, TIM17_CH1N, TSC_G5_IO4 - 59 C3 43 A4 30 30 PB7 I/O FTf - 60 B4 44 B4 31 31 BOOT0 I B - FTf (4)(5) I2C1_SCL, CEC, TIM16_CH1, TSC_SYNC - I2C1_SDA, IR_OUT, TIM17_CH1, EVENTOUT - 61 B3 45 - - 32 PB8 I/O Boot memory selection 62 A3 46 - - - PB9 I/O FTf (5) 63 D5 47 D6 32 0 VSS S - - Ground 64 E5 48 A5 1 1 VDD S - - Digital power supply 1. PC13, PC14 and PC15 are supplied through the power switch. Since the switch only sinks a limited amount of current (3 mA), the use of GPIOs PC13 to PC15 in output mode is limited: - The speed should not exceed 2 MHz with a maximum load of 30 pF. - These GPIOs must not be used as current sources (e.g. to drive an LED). 2. After the first RTC domain power-up, PC13, PC14 and PC15 operate as GPIOs. Their function then depends on the content of the RTC registers which are not reset by the main reset. For details on how to manage these GPIOs, refer to the RTC domain and RTC register descriptions in the reference manual. 3. Distinct VSSA pin is only available on packages with 48 and more pins. For all other packages, the pin number corresponds to the VSS pin to which VSSA pad of the silicon die is connected. 4. On the LQFP32 package, PB2 and PB8 must be set to defined levels by software, as their corresponding pads on the silicon die are left unconnected. Apply the same recommendations as for unconnected pins. 5. On the WLCSP36 package, PB8, PB9, PB10, PB11, PB12, PB13, PB14 and PB15 must be set to defined levels by software, as their corresponding pads on the silicon die are left unconnected. Apply the same recommendations as for unconnected pins. 6. After reset, these pins are configured as SWDIO and SWCLK alternate functions, and the internal pull-up on the SWDIO pin and the internal pull-down on the SWCLK pin are activated. 36/121 DocID022265 Rev 6 Pin name AF0 AF1 AF2 AF3 AF4 DocID022265 Rev 6 AF5 AF6 AF7 PA0 - USART2_CTS TIM2_CH1_ETR TSC_G1_IO1 - - COMP1_OUT PA1 EVENTOUT USART2_RTS TIM2_CH2 TSC_G1_IO2 - - PA2 TIM15_CH1 USART2_TX TIM2_CH3 TSC_G1_IO3 - - - COMP2_OUT PA3 TIM15_CH2 USART2_RX TIM2_CH4 TSC_G1_IO4 - - - - PA4 SPI1_NSS, I2S1_WS USART2_CK - TSC_G2_IO1 TIM14_CH1 - - - PA5 SPI1_SCK, I2S1_CK CEC TIM2_CH1_ETR TSC_G2_IO2 - - - - PA6 SPI1_MISO, I2S1_MCK TIM3_CH1 TIM1_BKIN TSC_G2_IO3 TIM16_CH1 EVENTOUT COMP1_OUT PA7 SPI1_MOSI, I2S1_SD TIM3_CH2 TIM1_CH1N TSC_G2_IO4 TIM17_CH1 EVENTOUT COMP2_OUT PA8 MCO USART1_CK TIM1_CH1 EVENTOUT - - - PA9 TIM15_BKIN USART1_TX TIM1_CH2 TSC_G4_IO1 - - - - PA10 TIM17_BKIN USART1_RX TIM1_CH3 TSC_G4_IO2 - - - - PA11 EVENTOUT USART1_CTS TIM1_CH4 TSC_G4_IO3 - - - COMP1_OUT PA12 EVENTOUT USART1_RTS TIM1_ETR TSC_G4_IO4 - - - COMP2_OUT PA13 SWDIO IR_OUT - - - - - PA14 SWCLK USART2_TX - - - - - - PA15 SPI1_NSS, I2S1_WS USART2_RX TIM2_CH1_ETR EVENTOUT - - - TIM14_CH1 STM32F051x4 STM32F051x6 STM32F051x8 Table 14. Alternate functions selected through GPIOA_AFR registers for port A 37/121 38/121 Table 15. Alternate functions selected through GPIOB_AFR registers for port B Pin name AF0 AF1 AF2 AF3 PB0 EVENTOUT TIM3_CH3 TIM1_CH2N TSC_G3_IO2 PB1 TIM14_CH1 TIM3_CH4 TIM1_CH3N TSC_G3_IO3 PB2 TSC_G3_IO4 SPI1_SCK, I2S1_CK EVENTOUT TIM2_CH2 TSC_G5_IO1 PB4 SPI1_MISO, I2S1_MCK TIM3_CH1 EVENTOUT TSC_G5_IO2 PB5 SPI1_MOSI, I2S1_SD TIM3_CH2 TIM16_BKIN I2C1_SMBA PB6 USART1_TX I2C1_SCL TIM16_CH1N TSC_G5_IO3 PB7 USART1_RX I2C1_SDA TIM17_CH1N TSC_G5_IO4 PB8 CEC I2C1_SCL TIM16_CH1 TSC_SYNC PB9 IR_OUT I2C1_SDA TIM17_CH1 EVENTOUT PB10 CEC I2C2_SCL TIM2_CH3 TSC_SYNC PB11 EVENTOUT I2C2_SDA TIM2_CH4 TSC_G6_IO1 PB12 SPI2_NSS EVENTOUT TIM1_BKIN TSC_G6_IO2 PB13 SPI2_SCK TIM1_CH1N TSC_G6_IO3 PB14 SPI2_MISO TIM15_CH1 TIM1_CH2N TSC_G6_IO4 PB15 SPI2_MOSI TIM15_CH2 TIM1_CH3N TIM15_CH1N STM32F051x4 STM32F051x6 STM32F051x8 DocID022265 Rev 6 PB3 STM32F051x4 STM32F051x6 STM32F051x8 5 Memory mapping Memory mapping To the difference of STM32F051x8 memory map in Figure 10, the two bottom code memory spaces of STM32F051x4/STM32F051x6 end at 0x0000 3FFF/0x0000 7FFF and 0x0800 3FFF/0x0000 7FFF, respectively. Figure 10. STM32F051x8 memory map [)))))))) [)) 5HVHUYHG $+% [( [( [ &RUWH[0LQWHUQDO SHULSKHUDOV 5HVHUYHG 5HVHUYHG [& [)) $+% 5HVHUYHG [ 5HVHUYHG [$ [ 5HVHUYHG [))))))) [))))& [)))) [ $3% 5HVHUYHG 2SWLRQ%\WHV [ 5HVHUYHG 6\VWHPPHPRU\ 5HVHUYHG [ [)))(& $3% [ [ [ 5HVHUYHG 5HVHUYHG 3HULSKHUDOV [ 5HVHUYHG )ODVKPHPRU\ [ 65$0 [ 5HVHUYHG &2'( [ )ODVKV\VWHP PHPRU\RU65$0 GHSHQGLQJRQ%227 FRQILJXUDWLRQ [ [ 069 DocID022265 Rev 6 39/121 41 Memory mapping STM32F051x4 STM32F051x6 STM32F051x8 Table 16. STM32F051xx peripheral register boundary addresses Bus AHB2 AHB1 APB 40/121 Boundary address Size Peripheral 0x4800 1800 - 0x5FFF FFFF ~384 MB Reserved 0x4800 1400 - 0x4800 17FF 1 KB GPIOF 0x4800 1000 - 0x4800 13FF 1 KB Reserved 0x4800 0C00 - 0x4800 0FFF 1 KB GPIOD 0x4800 0800 - 0x4800 0BFF 1 KB GPIOC 0x4800 0400 - 0x4800 07FF 1 KB GPIOB 0x4800 0000 - 0x4800 03FF 1 KB GPIOA 0x4002 4400 - 0x47FF FFFF ~128 MB Reserved 0x4002 4000 - 0x4002 43FF 1 KB TSC 0x4002 3400 - 0x4002 3FFF 3 KB Reserved 0x4002 3000 - 0x4002 33FF 1 KB CRC 0x4002 2400 - 0x4002 2FFF 3 KB Reserved 0x4002 2000 - 0x4002 23FF 1 KB Flash memory interface 0x4002 1400 - 0x4002 1FFF 3 KB Reserved 0x4002 1000 - 0x4002 13FF 1 KB RCC 0x4002 0400 - 0x4002 0FFF 3 KB Reserved 0x4002 0000 - 0x4002 03FF 1 KB DMA 0x4001 8000 - 0x4001 FFFF 32 KB Reserved 0x4001 5C00 - 0x4001 7FFF 9 KB Reserved 0x4001 5800 - 0x4001 5BFF 1 KB DBGMCU 0x4001 4C00 - 0x4001 57FF 3 KB Reserved 0x4001 4800 - 0x4001 4BFF 1 KB TIM17 0x4001 4400 - 0x4001 47FF 1 KB TIM16 0x4001 4000 - 0x4001 43FF 1 KB TIM15 0x4001 3C00 - 0x4001 3FFF 1 KB Reserved 0x4001 3800 - 0x4001 3BFF 1 KB USART1 0x4001 3400 - 0x4001 37FF 1 KB Reserved 0x4001 3000 - 0x4001 33FF 1 KB SPI1/I2S1 0x4001 2C00 - 0x4001 2FFF 1 KB TIM1 0x4001 2800 - 0x4001 2BFF 1 KB Reserved 0x4001 2400 - 0x4001 27FF 1 KB ADC 0x4001 0800 - 0x4001 23FF 7 KB Reserved 0x4001 0400 - 0x4001 07FF 1 KB EXTI 0x4001 0000 - 0x4001 03FF 1 KB SYSCFG + COMP 0x4000 8000 - 0x4000 FFFF 32 KB Reserved DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Memory mapping Table 16. STM32F051xx peripheral register boundary addresses (continued) Bus APB Boundary address Size Peripheral 0x4000 7C00 - 0x4000 7FFF 1 KB Reserved 0x4000 7800 - 0x4000 7BFF 1 KB CEC 0x4000 7400 - 0x4000 77FF 1 KB DAC 0x4000 7000 - 0x4000 73FF 1 KB PWR 0x4000 5C00 - 0x4000 6FFF 5 KB Reserved 0x4000 5800 - 0x4000 5BFF 1 KB I2C2 0x4000 5400 - 0x4000 57FF 1 KB I2C1 0x4000 4800 - 0x4000 53FF 3 KB Reserved 0x4000 4400 - 0x4000 47FF 1 KB USART2 0x4000 3C00 - 0x4000 43FF 2 KB Reserved 0x4000 3800 - 0x4000 3BFF 1 KB SPI2 0x4000 3400 - 0x4000 37FF 1 KB Reserved 0x4000 3000 - 0x4000 33FF 1 KB IWDG 0x4000 2C00 - 0x4000 2FFF 1 KB WWDG 0x4000 2800 - 0x4000 2BFF 1 KB RTC 0x4000 2400 - 0x4000 27FF 1 KB Reserved 0x4000 2000 - 0x4000 23FF 1 KB TIM14 0x4000 1400 - 0x4000 1FFF 3 KB Reserved 0x4000 1000 - 0x4000 13FF 1 KB TIM6 0x4000 0800 - 0x4000 0FFF 2 KB Reserved 0x4000 0400 - 0x4000 07FF 1 KB TIM3 0x4000 0000 - 0x4000 03FF 1 KB TIM2 DocID022265 Rev 6 41/121 41 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 6 Electrical characteristics 6.1 Parameter conditions Unless otherwise specified, all voltages are referenced to VSS. 6.1.1 Minimum and maximum values Unless otherwise specified, the minimum and maximum values are guaranteed in the worst conditions of ambient temperature, supply voltage and frequencies by tests in production on 100% of the devices with an ambient temperature at TA = 25 C and TA = TAmax (given by the selected temperature range). Data based on characterization results, design simulation and/or technology characteristics are indicated in the table footnotes and are not tested in production. Based on characterization, the minimum and maximum values refer to sample tests and represent the mean value plus or minus three times the standard deviation (mean 3). 6.1.2 Typical values Unless otherwise specified, typical data are based on TA = 25 C, VDD = VDDA = 3.3 V. They are given only as design guidelines and are not tested. Typical ADC accuracy values are determined by characterization of a batch of samples from a standard diffusion lot over the full temperature range, where 95% of the devices have an error less than or equal to the value indicated (mean 2). 6.1.3 Typical curves Unless otherwise specified, all typical curves are given only as design guidelines and are not tested. 6.1.4 Loading capacitor The loading conditions used for pin parameter measurement are shown in Figure 11. 6.1.5 Pin input voltage The input voltage measurement on a pin of the device is described in Figure 12. Figure 11. Pin loading conditions Figure 12. Pin input voltage 0&8SLQ 0&8SLQ & S) 9,1 069 42/121 DocID022265 Rev 6 069 STM32F051x4 STM32F051x6 STM32F051x8 6.1.6 Electrical characteristics Power supply scheme Figure 13. Power supply scheme 9%$7 %DFNXSFLUFXLWU\ /6(57& %DFNXSUHJLVWHUV 9 3RZHUVZLWFK 9'' 9&25( [9'' 5HJXODWRU 287 [Q) *3,2V ,1 [) /HYHOVKLIWHU 9'',2 ,2 ORJLF .HUQHOORJLF &38'LJLWDO 0HPRULHV [966 9''$ 9''$ Q) ) 95() 95() $'& '$& $QDORJ 5&V3// 966$ 069 Caution: Each power supply pair (VDD/VSS, VDDA/VSSA etc.) must be decoupled with filtering ceramic capacitors as shown above. These capacitors must be placed as close as possible to, or below, the appropriate pins on the underside of the PCB to ensure the good functionality of the device. DocID022265 Rev 6 43/121 90 Electrical characteristics 6.1.7 STM32F051x4 STM32F051x6 STM32F051x8 Current consumption measurement Figure 14. Current consumption measurement scheme , ''B9%$7 9%$7 ,'' 9'' ,''$ 9''$ 069 44/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 6.2 Electrical characteristics Absolute maximum ratings Stresses above the absolute maximum ratings listed in Table 17: Voltage characteristics, Table 18: Current characteristics and Table 19: Thermal characteristics may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these conditions is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. Table 17. Voltage characteristics(1) Symbol Ratings Min Max Unit VDD-VSS External main supply voltage - 0.3 4.0 V VDDA-VSS External analog supply voltage - 0.3 4.0 V VDD-VDDA Allowed voltage difference for VDD > VDDA - 0.4 V VBAT-VSS External backup supply voltage - 0.3 4.0 V 4.0(3) Input voltage on FT and FTf pins VSS -0.3 VDDIOx + Input voltage on TTa pins VSS -0.3 4.0 V 0 9.0 V VSS - 0.3 4.0 V Variations between different VDD power pins - 50 mV |VSSx - VSS| Variations between all the different ground pins - 50 mV VESD(HBM) Electrostatic discharge voltage (human body model) VIN(2) BOOT0 Input voltage on any other pin |VDDx| V see Section 6.3.12: Electrical sensitivity characteristics - 1. All main power (VDD, VDDA) and ground (VSS, VSSA) pins must always be connected to the external power supply, in the permitted range. 2. VIN maximum must always be respected. Refer to Table 18: Current characteristics for the maximum allowed injected current values. 3. Valid only if the internal pull-up/pull-down resistors are disabled. If internal pull-up or pull-down resistor is enabled, the maximum limit is 4 V. DocID022265 Rev 6 45/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 Table 18. Current characteristics Symbol Ratings Max. IVDD Total current into sum of all VDD power lines (source)(1) 120 IVSS (1) -120 Total current out of sum of all VSS ground lines (sink) IVDD(PIN) Maximum current into each VDD power pin (source) (1) 100 IVSS(PIN) Maximum current out of each VSS ground pin (sink)(1) -100 IIO(PIN) IIO(PIN) Output current sunk by any I/O and control pin 25 Output current source by any I/O and control pin Total output current sunk by sum of all I/Os and control pins -25 (2) 80 Total output current sourced by sum of all I/Os and control pins(2) -80 IINJ(PIN) Injected current on TC and RST pin Injected current on TTa pins IINJ(PIN) mA -5/+0(4) Injected current on B, FT and FTf pins (3) Unit 5 (5) 5 Total injected current (sum of all I/O and control pins)(6) 25 1. All main power (VDD, VDDA) and ground (VSS, VSSA) pins must always be connected to the external power supply, in the permitted range. 2. This current consumption must be correctly distributed over all I/Os and control pins. The total output current must not be sunk/sourced between two consecutive power supply pins referring to high pin count QFP packages. 3. A positive injection is induced by VIN > VDDIOx while a negative injection is induced by VIN < VSS. IINJ(PIN) must never be exceeded. Refer to Table 17: Voltage characteristics for the maximum allowed input voltage values. 4. Positive injection is not possible on these I/Os and does not occur for input voltages lower than the specified maximum value. 5. On these I/Os, a positive injection is induced by VIN > VDDA. Negative injection disturbs the analog performance of the device. See note (2) below Table 54: ADC accuracy. 6. When several inputs are submitted to a current injection, the maximum IINJ(PIN) is the absolute sum of the positive and negative injected currents (instantaneous values). Table 19. Thermal characteristics Symbol TSTG TJ 46/121 Ratings Storage temperature range Maximum junction temperature DocID022265 Rev 6 Value Unit -65 to +150 C 150 C STM32F051x4 STM32F051x6 STM32F051x8 6.3 Operating conditions 6.3.1 General operating conditions Electrical characteristics Table 20. General operating conditions Symbol Parameter Conditions Min Max fHCLK Internal AHB clock frequency - 0 48 fPCLK Internal APB clock frequency - 0 48 VDD Standard operating voltage - 2.0 3.6 VDD 3.6 2.4 3.6 1.65 3.6 TC and RST I/O -0.3 VDDIOx+0.3 TTa I/O -0.3 VDDA+0.3(1) FT and FTf I/O -0.3 5.5(1) BOOT0 0 5.5 LQFP64 - 444 LQFP48 - 364 LQFP32 - 357 UFQFPN32 - 526 UFQFPN48 - 625 UFBGA64 - 308 WLCSP36 - 333 -40 85 -40 105 -40 105 -40 125 Suffix 6 version -40 105 Suffix 7 version -40 125 VDDA VBAT VIN PD Analog operating voltage (ADC and DAC not used) Analog operating voltage (ADC and DAC used) Backup operating voltage - I/O input voltage Power dissipation at TA = 85 C for suffix 6 or TA = 105 C for suffix 7(2) Ambient temperature for the suffix 6 version Maximum power dissipation Ambient temperature for the suffix 7 version Maximum power dissipation TA TJ Must have a potential equal to or higher than VDD Junction temperature range Low power dissipation Low power dissipation (3) (3) Unit MHz V V V V mW C C C 1. For operation with a voltage higher than VDDIOx + 0.3 V, the internal pull-up resistor must be disabled. 2. If TA is lower, higher PD values are allowed as long as TJ does not exceed TJmax. See Section 7.8: Thermal characteristics. 3. In low power dissipation state, TA can be extended to this range as long as TJ does not exceed TJmax (see Section 7.8: Thermal characteristics). 6.3.2 Operating conditions at power-up / power-down The parameters given in Table 21 are derived from tests performed under the ambient temperature condition summarized in Table 20. DocID022265 Rev 6 47/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 Table 21. Operating conditions at power-up / power-down Symbol Parameter VDD rise time rate tVDD - VDD fall time rate VDDA rise time rate tVDDA 6.3.3 Conditions - VDDA fall time rate Min Max 0 20 0 20 Unit s/V Embedded reset and power control block characteristics The parameters given in Table 22 are derived from tests performed under the ambient temperature and supply voltage conditions summarized in Table 20: General operating conditions. Table 22. Embedded reset and power control block characteristics Symbol VPOR/PDR(1) VPDRhyst tRSTTEMPO(4) Parameter Conditions Min Typ Max Unit Power on/power down reset threshold Falling edge(2) 1.80 1.88 1.96(3) V 1.84(3) 1.92 2.00 V PDR hysteresis - - 40 - mV Reset temporization - 1.50 2.50 4.50 ms Rising edge 1. The PDR detector monitors VDD and also VDDA (if kept enabled in the option bytes). The POR detector monitors only VDD. 2. The product behavior is guaranteed by design down to the minimum VPOR/PDR value. 3. Data based on characterization results, not tested in production. 4. Guaranteed by design, not tested in production. Table 23. Programmable voltage detector characteristics Symbol 48/121 Parameter VPVD0 PVD threshold 0 VPVD1 PVD threshold 1 VPVD2 PVD threshold 2 VPVD3 PVD threshold 3 VPVD4 PVD threshold 4 VPVD5 PVD threshold 5 Conditions Min Typ Max Unit Rising edge 2.1 2.18 2.26 V Falling edge 2 2.08 2.16 V Rising edge 2.19 2.28 2.37 V Falling edge 2.09 2.18 2.27 V Rising edge 2.28 2.38 2.48 V Falling edge 2.18 2.28 2.38 V Rising edge 2.38 2.48 2.58 V Falling edge 2.28 2.38 2.48 V Rising edge 2.47 2.58 2.69 V Falling edge 2.37 2.48 2.59 V Rising edge 2.57 2.68 2.79 V Falling edge 2.47 2.58 2.69 V DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics Table 23. Programmable voltage detector characteristics (continued) Symbol Parameter Conditions Min Typ Max Unit Rising edge 2.66 2.78 2.9 V Falling edge 2.56 2.68 2.8 V Rising edge 2.76 2.88 3 V Falling edge 2.66 2.78 2.9 V VPVD6 PVD threshold 6 VPVD7 PVD threshold 7 VPVDhyst(1) PVD hysteresis - 100 - mV PVD current consumption - 0.15 0.26(1) A IDD(PVD) 1. Guaranteed by design, not tested in production. 6.3.4 Embedded reference voltage The parameters given in Table 24 are derived from tests performed under the ambient temperature and supply voltage conditions summarized in Table 20: General operating conditions. Table 24. Embedded internal reference voltage Symbol VREFINT Parameter Conditions Internal reference voltage -40 C < TA < +105 C Min Typ Max Unit 1.16 1.2 1.25 V tSTART ADC_IN17 buffer startup time - - - 10(1) s tS_vrefint ADC sampling time when reading the internal reference voltage - 4(1) - - s VREFINT Internal reference voltage spread over the temperature range VDDA = 3 V - - 10(1) mV - - 100(1) - 100(1) ppm/C TCoeff Temperature coefficient 1. Guaranteed by design, not tested in production. 6.3.5 Supply current characteristics The current consumption is a function of several parameters and factors such as the operating voltage, ambient temperature, I/O pin loading, device software configuration, operating frequencies, I/O pin switching rate, program location in memory and executed binary code. The current consumption is measured as described in Figure 14: Current consumption measurement scheme. All Run-mode current consumption measurements given in this section are performed with a reduced code that gives a consumption equivalent to CoreMark code. DocID022265 Rev 6 49/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 Typical and maximum current consumption The MCU is placed under the following conditions: * All I/O pins are in analog input mode * All peripherals are disabled except when explicitly mentioned * * The Flash memory access time is adjusted to the fHCLK frequency: - 0 wait state and Prefetch OFF from 0 to 24 MHz - 1 wait state and Prefetch ON above 24 MHz When the peripherals are enabled fPCLK = fHCLK The parameters given in Table 25 to Table 31 are derived from tests performed under ambient temperature and supply voltage conditions summarized in Table 20: General operating conditions. Table 25. Typical and maximum current consumption from VDD at 3.6 V All peripherals enabled Symbol Parameter Conditions HSE bypass, PLL on Supply current in Run mode, code executing from Flash memory HSE bypass, PLL off HSI clock, PLL on HSI clock, PLL off IDD HSE bypass, PLL on Supply current in Run mode, code executing from RAM HSE bypass, PLL off HSI clock, PLL on HSI clock, PLL off 50/121 fHCLK Max @ TA(1) Typ All peripherals disabled Max @ TA(1) Typ 25 C 85 C 105 C 48 MHz 22.0 22.8 22.8 23.8 32 MHz 15.0 15.5 15.5 24 MHz 12.2 13.2 8 MHz 4.4 1 MHz Unit 25 C 85 C 105 C 11.8 12.7 12.7 13.3 16.0 7.6 8.7 8.7 9.0 13.2 13.6 7.2 7.9 7.9 8.1 5.2 5.2 5.4 2.7 2.9 2.9 3.0 1.0 1.3 1.3 1.4 0.7 0.9 0.9 0.9 48 MHz 22.0 22.8 22.8 23.8 11.8 12.7 12.7 13.3 32 MHz 15.0 15.5 15.5 16.0 7.6 8.7 8.7 9.0 24 MHz 12.2 13.2 13.2 13.6 7.2 7.9 7.9 8.1 8 MHz 5.2 5.2 5.4 2.7 2.9 2.9 3.0 48 MHz 22.2 23.2(2) 23.2 24.4(2) 12.0 12.7(2) 12.7 13.3(2) 32 MHz 15.4 16.3 16.3 16.8 7.8 8.7 8.7 9.0 24 MHz 11.2 12.2 12.2 12.8 6.2 7.9 7.9 8.1 8 MHz 4.0 4.5 4.5 4.7 1.9 2.9 2.9 3.0 1 MHz 0.6 0.8 0.8 0.9 0.3 0.6 0.6 0.7 48 MHz 22.2 23.2 23.2 24.4 12.0 12.7 12.7 13.3 32 MHz 15.4 16.3 16.3 16.8 7.8 8.7 8.7 9.0 24 MHz 11.2 12.2 12.2 12.8 6.2 7.9 7.9 8.1 8 MHz 4.5 4.5 4.7 1.9 2.9 2.9 3.0 4.4 4.0 DocID022265 Rev 6 mA STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics Table 25. Typical and maximum current consumption from VDD at 3.6 V (continued) All peripherals enabled Symbol Parameter Conditions HSE bypass, PLL on IDD Supply current in Sleep mode HSE bypass, PLL off HSI clock, PLL on HSI clock, PLL off fHCLK Max @ TA(1) Typ All peripherals disabled Max @ TA(1) Typ 25 C 85 C 105 C 48 MHz 14.0 15.3(2) 15.3 16.0(2) 32 MHz 9.5 10.2 10.2 24 MHz 7.3 7.8 8 MHz 2.6 1 MHz Unit 25 C 85 C 105 C 2.8 3.0(2) 3.0 3.2(2) 10.7 2.0 2.1 2.1 2.3 7.8 8.3 1.5 1.7 1.7 1.9 2.9 2.9 3.0 0.6 0.8 0.8 0.8 0.4 0.6 0.6 0.6 0.2 0.4 0.4 0.4 48 MHz 14.0 15.3 15.3 16.0 3.8 4.0 4.1 4.2 32 MHz 9.5 10.2 10.2 10.7 2.6 2.7 2.8 2.8 24 MHz 7.3 7.8 7.8 8.3 2.0 2.1 2.1 2.1 8 MHz 2.6 2.9 2.9 3.0 0.6 0.8 0.8 0.8 mA 1. Data based on characterization results, not tested in production unless otherwise specified. 2. Data based on characterization results and tested in production (using one common test limit for sum of IDD and IDDA). Table 26. Typical and maximum current consumption from the VDDA supply VDDA = 2.4 V Symbol Parameter Conditions (1) VDDA = 3.6 V Max @ TA(2) fHCLK Max @ TA(2) Typ 25 C IDDA Supply current in Run or Sleep mode, code executing from Flash memory or RAM HSE bypass, PLL on HSE bypass, PLL off HSI clock, PLL on HSI clock, PLL off Unit Typ 85 C 105 C 25 C 85 C 105 C 48 MHz 150 170(3) 178 182(3) 164 183(3) 195 198(3) 32 MHz 104 121 126 128 113 129 135 138 24 MHz 82 96 100 103 88 102 106 108 8 MHz 2.0 2.7 3.1 3.3 3.5 3.8 4.1 4.4 1 MHz 2.0 2.7 3.1 3.3 3.5 3.8 4.1 4.4 48 MHz 220 240 248 252 244 263 275 278 32 MHz 174 191 196 198 193 209 215 218 24 MHz 152 167 173 174 168 183 190 192 8 MHz 72 79 82 83 83.5 91 94 95 A 1. Current consumption from the VDDA supply is independent of whether the digital peripherals are enabled or disabled, being in Run or Sleep mode or executing from Flash memory or RAM. Furthermore, when the PLL is off, IDDA is independent of clock frequencies. 2. Data based on characterization results, not tested in production unless otherwise specified. 3. Data based on characterization results and tested in production (using one common test limit for sum of IDD and IDDA). DocID022265 Rev 6 51/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 Table 27. Typical and maximum current consumption in Stop and Standby modes Parameter IDD Supply current in Standby mode Supply current in Stop mode IDDA Supply current in Standby mode Supply current in Stop mode Supply current in Standby mode 2.0 V 2.4 V 2.7 V 3.0 V 3.3 V 3.6 V TA = TA = TA = 25 C 85 C 105 C Regulator in run mode, all oscillators OFF 15 15.1 15.3 15.5 15.7 16 (2) (2) Regulator in lowpower mode, all oscillators OFF 3.2 3.3 3.4 3.5 3.7 4 (2) (2) LSI ON and IWDG ON 0.8 1.0 1.1 1.2 1.4 1.5 - - - LSI OFF and IWDG OFF 0.7 0.8 0.9 1.0 1.1 1.3 2(2) 2.5 3(2) Regulator in run mode, all oscillators OFF 1.9 2 2.2 2.3 2.5 2.6 3.5(2) 3.5 4.5(2) Regulator in lowpower mode, all oscillators OFF 1.9 2 2.2 2.3 2.5 2.6 3.5(2) 3.5 4.5(2) LSI ON and IWDG ON 2.3 2.5 2.7 2.9 3.1 3.3 - - - LSI OFF and IWDG OFF 1.8 1.9 2 2.2 2.3 2.5 3.5(2) 3.5 4.5(2) Regulator in run mode, all oscillators OFF 1.1 1.2 1.2 1.2 1.3 1.4 - - - Regulator in lowpower mode, all oscillators OFF 1.1 1.2 1.2 1.2 1.3 1.4 - - - LSI ON and IWDG ON 1.5 1.6 1.7 1.8 1.9 2.0 - - - LSI OFF and IWDG OFF 1 1.0 1.1 1.1 1.2 1.2 - - - VDDA monitoring ON Supply current in Stop mode Conditions VDDA monitoring OFF Symbol Max(1) Typ @VDD (VDD = VDDA) A 1. Data based on characterization results, not tested in production unless otherwise specified. 2. Data based on characterization results and tested in production (using one common test limit for sum of IDD and IDDA). 52/121 Unit DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics Table 28. Typical and maximum current consumption from the VBAT supply Max(1) Typ @ VBAT 2.4 V 2.7 V 3.3 V 3.6 V RTC domain IDD_VBAT supply current Conditions 1.8 V Parameter 1.65 V Symbol TA = 25 C LSE & RTC ON; "Xtal mode": lower driving capability; LSEDRV[1:0] = '00' 0.5 0.5 0.6 0.7 0.8 0.9 1.0 LSE & RTC ON; "Xtal mode" higher driving capability; LSEDRV[1:0] = '11' 0.8 TA = TA = 85 C 105 C 1.3 Unit 1.7 A 0.8 0.9 1.0 1.1 1.2 1.3 1.6 2.1 1. Data based on characterization results, not tested in production. Typical current consumption The MCU is placed under the following conditions: * VDD = VDDA = 3.3 V * All I/O pins are in analog input configuration * The Flash memory access time is adjusted to fHCLK frequency: - 0 wait state and Prefetch OFF from 0 to 24 MHz - 1 wait state and Prefetch ON above 24 MHz * When the peripherals are enabled, fPCLK = fHCLK * PLL is used for frequencies greater than 8 MHz * AHB prescaler of 2, 4, 8 and 16 is used for the frequencies 4 MHz, 2 MHz, 1 MHz and 500 kHz respectively DocID022265 Rev 6 53/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 Table 29. Typical current consumption, code executing from Flash memory, running from HSE 8 MHz crystal Typical consumption in Run mode Symbol IDD IDDA Parameter Current consumption from VDD supply Current consumption from VDDA supply fHCLK Typical consumption in Sleep mode Unit Peripherals Peripherals Peripherals Peripherals enabled disabled enabled disabled 48 MHz 23.2 13.3 13.2 3.1 36 MHz 17.6 10.3 10.1 2.6 32 MHz 15.6 9.3 9.0 2.4 24 MHz 12.1 7.4 7.0 2.0 16 MHz 8.4 5.1 5.0 1.6 8 MHz 4.5 3.0 2.8 1.1 4 MHz 2.8 2.0 2.0 1.1 2 MHz 1.9 1.5 1.5 1.0 1 MHz 1.5 1.3 1.3 1.0 500 kHz 1.2 1.2 1.1 1.0 48 MHz 151 36 MHz 113 32 MHz 101 24 MHz 79 16 MHz 57 8 MHz 2.2 4 MHz 2.2 2 MHz 2.2 1 MHz 2.2 500 kHz 2.2 mA A I/O system current consumption The current consumption of the I/O system has two components: static and dynamic. I/O static current consumption All the I/Os used as inputs with pull-up generate current consumption when the pin is externally held low. The value of this current consumption can be simply computed by using the pull-up/pull-down resistors values given in Table 48: I/O static characteristics. For the output pins, any external pull-down or external load must also be considered to estimate the current consumption. Additional I/O current consumption is due to I/Os configured as inputs if an intermediate voltage level is externally applied. This current consumption is caused by the input Schmitt 54/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics trigger circuits used to discriminate the input value. Unless this specific configuration is required by the application, this supply current consumption can be avoided by configuring these I/Os in analog mode. This is notably the case of ADC input pins which should be configured as analog inputs. Caution: Any floating input pin can also settle to an intermediate voltage level or switch inadvertently, as a result of external electromagnetic noise. To avoid current consumption related to floating pins, they must either be configured in analog mode, or forced internally to a definite digital value. This can be done either by using pull-up/down resistors or by configuring the pins in output mode. I/O dynamic current consumption In addition to the internal peripheral current consumption measured previously (see Table 31: Peripheral current consumption), the I/Os used by an application also contribute to the current consumption. When an I/O pin switches, it uses the current from the I/O supply voltage to supply the I/O pin circuitry and to charge/discharge the capacitive load (internal or external) connected to the pin: I SW = V DDIOx x f SW x C where ISW is the current sunk by a switching I/O to charge/discharge the capacitive load VDDIOx is the I/O supply voltage fSW is the I/O switching frequency C is the total capacitance seen by the I/O pin: C = CINT + CEXT + CS CS is the PCB board capacitance including the pad pin. The test pin is configured in push-pull output mode and is toggled by software at a fixed frequency. DocID022265 Rev 6 55/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 Table 30. Switching output I/O current consumption Symbol Parameter Conditions(1) VDDIOx = 3.3 V C =CINT VDDIOx = 3.3 V CEXT = 0 pF C = CINT + CEXT+ CS VDDIOx = 3.3 V CEXT = 10 pF C = CINT + CEXT+ CS ISW I/O current consumption VDDIOx = 3.3 V CEXT = 22 pF C = CINT + CEXT+ CS VDDIOx = 3.3 V CEXT = 33 pF C = CINT + CEXT+ CS VDDIOx = 3.3 V CEXT = 47 pF C = CINT + CEXT+ CS C = Cint VDDIOx = 2.4 V CEXT = 47 pF C = CINT + CEXT+ CS C = Cint 1. CS = 7 pF (estimated value). 56/121 DocID022265 Rev 6 I/O toggling frequency (fSW) Typ 4 MHz 0.07 8 MHz 0.15 16 MHz 0.31 24 MHz 0.53 48 MHz 0.92 4 MHz 0.18 8 MHz 0.37 16 MHz 0.76 24 MHz 1.39 48 MHz 2.188 4 MHz 0.32 8 MHz 0.64 16 MHz 1.25 24 MHz 2.23 48 MHz 4.442 4 MHz 0.49 8 MHz 0.94 16 MHz 2.38 24 MHz 3.99 4 MHz 0.64 8 MHz 1.25 16 MHz 3.24 24 MHz 5.02 4 MHz 0.81 8 MHz 1.7 16 MHz 3.67 4 MHz 0.66 8 MHz 1.43 16 MHz 2.45 24 MHz 4.97 Unit mA STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics On-chip peripheral current consumption The current consumption of the on-chip peripherals is given in Table 31. The MCU is placed under the following conditions: * All I/O pins are in analog mode * All peripherals are disabled unless otherwise mentioned * The given value is calculated by measuring the current consumption * - with all peripherals clocked off - with only one peripheral clocked on Ambient operating temperature and supply voltage conditions summarized in Table 17: Voltage characteristics Table 31. Peripheral current consumption Peripheral AHB Typical consumption at 25 C BusMatrix(1) 5 DMA1 7 SRAM 1 Flash memory interface 14 CRC 2 GPIOA 9 GPIOB 12 GPIOC 2 GPIOD 1 GPIOF 1 TSC 6 All AHB peripherals 55 DocID022265 Rev 6 Unit A/MHz 57/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 Table 31. Peripheral current consumption (continued) Peripheral APB-Bridge APB Typical consumption at 25 C (2) Unit 3 SYSCFG 3 ADC(3) 5 TIM1 17 SPI1 10 USART1 19 TIM15 11 TIM16 8 TIM17 8 DBG (MCU Debug Support) 0.5 TIM2 17 TIM3 13 TIM6 3 TIM14 6 WWDG 1 SPI2 7 USART2 7 I2C1 4 I2C2 5 DAC 2 PWR 1 CEC 2 All APB peripherals A/MHz 149 1. The BusMatrix automatically is active when at least one master is ON (CPU or DMA1) 2. The APBx Bridge is automatically active when at least one peripheral is ON on the same Bus. 3. The power consumption of the analog part (IDDA) of peripherals such as ADC is not included. Refer to the tables of characteristics in the subsequent sections. 58/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 6.3.6 Electrical characteristics Wakeup time from low-power mode The wakeup times given in Table 32 are the latency between the event and the execution of the first user instruction. The device goes in low-power mode after the WFE (Wait For Event) instruction, in the case of a WFI (Wait For Interruption) instruction, 16 CPU cycles must be added to the following timings due to the interrupt latency in the Cortex M0 architecture. The SYSCLK clock source setting is kept unchanged after wakeup from Sleep mode. During wakeup from Stop or Standby mode, SYSCLK takes the default setting: HSI 8 MHz. The wakeup source from Sleep and Stop mode is an EXTI line configured in event mode. The wakeup source from Standby mode is the WKUP1 pin (PA0). All timings are derived from tests performed under the ambient temperature and supply voltage conditions summarized in Table 20: General operating conditions. Table 32. Low-power mode wakeup timings Typ @VDD = VDDA Symbol Parameter Conditions Max Unit = 2.0 V = 2.4 V = 2.7 V tWUSTOP Wakeup from Stop mode Wakeup from tWUSTANDBY Standby mode tWUSLEEP 6.3.7 = 3.3 V Regulator in run mode 3.2 3.1 2.9 2.9 2.8 5 Regulator in low power mode 7.0 5.8 5.2 4.9 4.6 9 - Wakeup from Sleep mode =3V s 60.4 - 55.6 53.5 52 51 4 SYSCLK cycles - External clock source characteristics High-speed external user clock generated from an external source In bypass mode the HSE oscillator is switched off and the input pin is a standard GPIO. The external clock signal has to respect the I/O characteristics in Section 6.3.14. However, the recommended clock input waveform is shown in Figure 15: High-speed external clock source AC timing diagram. Table 33. High-speed external user clock characteristics Symbol Parameter(1) Min Typ Max Unit - 8 32 MHz fHSE_ext User external clock source frequency VHSEH OSC_IN input pin high level voltage 0.7 VDDIOx - VDDIOx VHSEL OSC_IN input pin low level voltage VSS - 0.3 VDDIOx 15 - - tw(HSEH) tw(HSEL) OSC_IN high or low time tr(HSE) tf(HSE) OSC_IN rise or fall time V ns DocID022265 Rev 6 - - 20 59/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 1. Guaranteed by design, not tested in production. Figure 15. High-speed external clock source AC timing diagram WZ +6(+ 9+6(+ 9+6(/ WU +6( WI +6( W WZ +6(/ 7+6( 069 Low-speed external user clock generated from an external source In bypass mode the LSE oscillator is switched off and the input pin is a standard GPIO. The external clock signal has to respect the I/O characteristics in Section 6.3.14. However, the recommended clock input waveform is shown in Figure 16. Table 34. Low-speed external user clock characteristics Parameter(1) Symbol fLSE_ext User external clock source frequency Min Typ Max Unit - 32.768 1000 kHz VLSEH OSC32_IN input pin high level voltage 0.7 VDDIOx - VDDIOx VLSEL OSC32_IN input pin low level voltage VSS - 0.3 VDDIOx 450 - - - - 50 tw(LSEH) OSC32_IN high or low time tw(LSEL) tr(LSE) tf(LSE) V ns OSC32_IN rise or fall time 1. Guaranteed by design, not tested in production. Figure 16. Low-speed external clock source AC timing diagram WZ /6(+ 9/6(+ 9/6(/ WU /6( WI /6( WZ /6(/ W 7/6( 069 60/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics High-speed external clock generated from a crystal/ceramic resonator The high-speed external (HSE) clock can be supplied with a 4 to 32 MHz crystal/ceramic resonator oscillator. All the information given in this paragraph are based on design simulation results obtained with typical external components specified in Table 35. In the application, the resonator and the load capacitors have to be placed as close as possible to the oscillator pins in order to minimize output distortion and startup stabilization time. Refer to the crystal resonator manufacturer for more details on the resonator characteristics (frequency, package, accuracy). Table 35. HSE oscillator characteristics Symbol fOSC_IN RF Conditions(1) Min(2) Typ Max(2) Unit Oscillator frequency - 4 8 32 MHz Feedback resistor - - 200 - k Parameter (3) During startup IDD gm tSU(HSE)(4) HSE current consumption Oscillator transconductance Startup time - 8.5 VDD = 3.3 V, Rm = 30 , CL = 10 pF@8 MHz - 0.4 - VDD = 3.3 V, Rm = 45 , CL = 10 pF@8 MHz - 0.5 - VDD = 3.3 V, Rm = 30 , CL = 5 pF@32 MHz - 0.8 - VDD = 3.3 V, Rm = 30 , CL = 10 pF@32 MHz - 1 - VDD = 3.3 V, Rm = 30 , CL = 20 pF@32 MHz - 1.5 - Startup 10 - - mA/V VDD is stabilized - 2 - ms mA 1. Resonator characteristics given by the crystal/ceramic resonator manufacturer. 2. Guaranteed by design, not tested in production. 3. This consumption level occurs during the first 2/3 of the tSU(HSE) startup time 4. tSU(HSE) is the startup time measured from the moment it is enabled (by software) to a stabilized 8 MHz oscillation is reached. This value is measured for a standard crystal resonator and it can vary significantly with the crystal manufacturer For CL1 and CL2, it is recommended to use high-quality external ceramic capacitors in the 5 pF to 20 pF range (Typ.), designed for high-frequency applications, and selected to match the requirements of the crystal or resonator (see Figure 17). CL1 and CL2 are usually the same size. The crystal manufacturer typically specifies a load capacitance which is the series combination of CL1 and CL2. PCB and MCU pin capacitance must be included (10 pF can be used as a rough estimate of the combined pin and board capacitance) when sizing CL1 and CL2. Note: For information on selecting the crystal, refer to the application note AN2867 "Oscillator design guide for ST microcontrollers" available from the ST website www.st.com. DocID022265 Rev 6 61/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 Figure 17. Typical application with an 8 MHz crystal 5HVRQDWRUZLWKLQWHJUDWHG FDSDFLWRUV &/ 26&B,1 0+] UHVRQDWRU &/ 5(;7 I+6( 5) %LDV FRQWUROOHG JDLQ 26&B287 069 1. REXT value depends on the crystal characteristics. Low-speed external clock generated from a crystal resonator The low-speed external (LSE) clock can be supplied with a 32.768 kHz crystal resonator oscillator. All the information given in this paragraph are based on design simulation results obtained with typical external components specified in Table 36. In the application, the resonator and the load capacitors have to be placed as close as possible to the oscillator pins in order to minimize output distortion and startup stabilization time. Refer to the crystal resonator manufacturer for more details on the resonator characteristics (frequency, package, accuracy). Table 36. LSE oscillator characteristics (fLSE = 32.768 kHz) Symbol IDD 62/121 Parameter LSE current consumption Conditions(1) Min(2) Typ LSEDRV[1:0]=00 lower driving capability - 0.5 0.9 LSEDRV[1:0]= 01 medium low driving capability - - 1 LSEDRV[1:0] = 10 medium high driving capability - - 1.3 LSEDRV[1:0]=11 higher driving capability - - 1.6 DocID022265 Rev 6 Max(2) Unit A STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics Table 36. LSE oscillator characteristics (fLSE = 32.768 kHz) Symbol gm tSU(LSE)(3) Conditions(1) Min(2) Typ LSEDRV[1:0]=00 lower driving capability 5 - - LSEDRV[1:0]= 01 medium low driving capability 8 - - LSEDRV[1:0] = 10 medium high driving capability 15 - - LSEDRV[1:0]=11 higher driving capability 25 - - VDDIOx is stabilized - 2 - Parameter Oscillator transconductance Startup time Max(2) Unit A/V s 1. Refer to the note and caution paragraphs below the table, and to the application note AN2867 "Oscillator design guide for ST microcontrollers". 2. Guaranteed by design, not tested in production. 3. tSU(LSE) is the startup time measured from the moment it is enabled (by software) to a stabilized 32.768 kHz oscillation is reached. This value is measured for a standard crystal and it can vary significantly with the crystal manufacturer Note: For information on selecting the crystal, refer to the application note AN2867 "Oscillator design guide for ST microcontrollers" available from the ST website www.st.com. Figure 18. Typical application with a 32.768 kHz crystal 5HVRQDWRUZLWKLQWHJUDWHG FDSDFLWRUV &/ 26&B,1 I/6( 'ULYH SURJUDPPDEOH DPSOLILHU N+] UHVRQDWRU 26&B287 &/ 069 Note: An external resistor is not required between OSC32_IN and OSC32_OUT and it is forbidden to add one. 6.3.8 Internal clock source characteristics The parameters given in Table 37 are derived from tests performed under ambient temperature and supply voltage conditions summarized in Table 20: General operating conditions. The provided curves are characterization results, not tested in production. DocID022265 Rev 6 63/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 High-speed internal (HSI) RC oscillator Table 37. HSI oscillator characteristics(1) Symbol Parameter fHSI Conditions Min Typ - - Frequency TRIM HSI user trimming step DuCy(HSI) Duty cycle Accuracy of the HSI oscillator ACCHSI - - - (2) 45 IDDA(HSI) Unit 8 - MHz - (2) - % 1 (2) 55 % TA = -40 to 105C (3) -2.8 - 3.8 TA = -10 to 85C -1.9(3) - 2.3(3) TA = 0 to 85C -1.9(3) - 2(3) TA = 0 to 70C -1.3(3) - 2(3) TA = 0 to 55C -1(3) - 2(3) -1 - 1 - 2(2) s 80 100(2) A TA = 25C(4) tsu(HSI) Max HSI oscillator startup time - 1(2) HSI oscillator power consumption - - (3) % 1. VDDA = 3.3 V, TA = -40 to 105C unless otherwise specified. 2. Guaranteed by design, not tested in production. 3. Data based on characterization results, not tested in production. 4. Factory calibrated, parts not soldered. Figure 19. HSI oscillator accuracy characterization results for soldered parts ."9 .*/ 5<$> " 069 64/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics High-speed internal 14 MHz (HSI14) RC oscillator (dedicated to ADC) Table 38. HSI14 oscillator characteristics(1) Symbol fHSI14 TRIM Parameter Conditions Min Typ - - 14 Frequency HSI14 user-trimming step DuCy(HSI14) Duty cycle - - - (2) 45 Accuracy of the HSI14 oscillator (factory calibrated) TA = -10 to 85 C TA = 25 C tsu(HSI14) IDDA(HSI14) - MHz (2) - % 1 55 (2) % (3) % (3) - 5.1 -3.2(3) - 3.1(3) % -2.5 - 2.3 (3) % -1 (3) TA = 0 to 70 C Unit - TA = -40 to 105 C -4.2 ACCHSI14 Max HSI14 oscillator startup time - 1(2) HSI14 oscillator power consumption - - - 1 % - 2(2) s 100 150(2) A 1. VDDA = 3.3 V, TA = -40 to 105 C unless otherwise specified. 2. Guaranteed by design, not tested in production. 3. Data based on characterization results, not tested in production. Figure 20. HSI14 oscillator accuracy characterization results -!8 -). 4! ; #= -36 DocID022265 Rev 6 65/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 Low-speed internal (LSI) RC oscillator Table 39. LSI oscillator characteristics(1) Symbol Parameter fLSI tsu(LSI) Min Typ Max Unit 30 40 50 kHz LSI oscillator startup time - - 85 s LSI oscillator power consumption - 0.75 1.2 A Frequency (2) IDDA(LSI)(2) 1. VDDA = 3.3 V, TA = -40 to 105 C unless otherwise specified. 2. Guaranteed by design, not tested in production. 6.3.9 PLL characteristics The parameters given in Table 40 are derived from tests performed under ambient temperature and supply voltage conditions summarized in Table 20: General operating conditions. Table 40. PLL characteristics Value Symbol fPLL_IN fPLL_OUT tLOCK JitterPLL Parameter Unit Min Typ Max 1(2) 8.0 24(2) MHz PLL input clock duty cycle (2) 40 - 60(2) % PLL multiplier output clock 16(2) - 48 MHz PLL lock time - - 200(2) s Cycle-to-cycle jitter - - 300(2) ps PLL input clock(1) 1. Take care to use the appropriate multiplier factors to obtain PLL input clock values compatible with the range defined by fPLL_OUT. 2. Guaranteed by design, not tested in production. 6.3.10 Memory characteristics Flash memory The characteristics are given at TA = -40 to 105 C unless otherwise specified. Table 41. Flash memory characteristics Min Typ Max(1) Unit 16-bit programming time TA = -40 to +105 C 40 53.5 60 s Page (1 KB) erase time TA = -40 to +105 C 20 - 40 ms tME Mass erase time TA = -40 to +105 C 20 - 40 ms IDD Supply current Write mode - - 10 mA Erase mode - - 12 mA Symbol tprog tERASE Parameter Conditions 1. Guaranteed by design, not tested in production. 66/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics Table 42. Flash memory endurance and data retention Symbol NEND Parameter Endurance Conditions TA = -40 to +105 C 1 tRET Data retention kcycle(2) Min(1) Unit 10 kcycle at TA = 85 C 30 at TA = 105 C 10 10 kcycle(2) at TA = 55 C 20 1 kcycle (2) Year 1. Data based on characterization results, not tested in production. 2. Cycling performed over the whole temperature range. 6.3.11 EMC characteristics Susceptibility tests are performed on a sample basis during device characterization. Functional EMS (electromagnetic susceptibility) While a simple application is executed on the device (toggling 2 LEDs through I/O ports). the device is stressed by two electromagnetic events until a failure occurs. The failure is indicated by the LEDs: * Electrostatic discharge (ESD) (positive and negative) is applied to all device pins until a functional disturbance occurs. This test is compliant with the IEC 61000-4-2 standard. * FTB: A Burst of Fast Transient voltage (positive and negative) is applied to VDD and VSS through a 100 pF capacitor, until a functional disturbance occurs. This test is compliant with the IEC 61000-4-4 standard. A device reset allows normal operations to be resumed. The test results are given in Table 43. They are based on the EMS levels and classes defined in application note AN1709. Table 43. EMS characteristics Symbol Parameter Conditions Level/ Class VFESD VDD = 3.3 V, LQFP64, TA = +25 C, Voltage limits to be applied on any I/O pin fHCLK = 48 MHz, to induce a functional disturbance conforming to IEC 61000-4-2 2B VEFTB Fast transient voltage burst limits to be applied through 100 pF on VDD and VSS pins to induce a functional disturbance VDD = 3.3 V, LQFP64, TA = +25C, fHCLK = 48 MHz, conforming to IEC 61000-4-4 4B Designing hardened software to avoid noise problems EMC characterization and optimization are performed at component level with a typical application environment and simplified MCU software. It should be noted that good EMC performance is highly dependent on the user application and the software in particular. Therefore it is recommended that the user applies EMC software optimization and prequalification tests in relation with the EMC level requested for his application. DocID022265 Rev 6 67/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 Software recommendations The software flowchart must include the management of runaway conditions such as: * Corrupted program counter * Unexpected reset * Critical Data corruption (for example control registers) Prequalification trials Most of the common failures (unexpected reset and program counter corruption) can be reproduced by manually forcing a low state on the NRST pin or the Oscillator pins for 1 second. To complete these trials, ESD stress can be applied directly on the device, over the range of specification values. When unexpected behavior is detected, the software can be hardened to prevent unrecoverable errors occurring (see application note AN1015). Electromagnetic Interference (EMI) The electromagnetic field emitted by the device are monitored while a simple application is executed (toggling 2 LEDs through the I/O ports). This emission test is compliant with IEC 61967-2 standard which specifies the test board and the pin loading. Table 44. EMI characteristics Symbol Parameter SEMI 6.3.12 Conditions Monitored frequency band 0.1 to 30 MHz VDD = 3.6 V, TA = 25 C, 30 to 130 MHz LQFP64 package Peak level compliant with 130 MHz to 1 GHz IEC 61967-2 EMI Level Max vs. [fHSE/fHCLK] Unit 8/48 MHz -3 28 dBV 23 4 - Electrical sensitivity characteristics Based on three different tests (ESD, LU) using specific measurement methods, the device is stressed in order to determine its performance in terms of electrical sensitivity. Electrostatic discharge (ESD) Electrostatic discharges (a positive then a negative pulse separated by 1 second) are applied to the pins of each sample according to each pin combination. The sample size depends on the number of supply pins in the device (3 parts x (n+1) supply pins). This test conforms to the JESD22-A114/C101 standard. 68/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics Table 45. ESD absolute maximum ratings Symbol Ratings Conditions Packages Class Maximum value(1) Unit VESD(HBM) Electrostatic discharge voltage TA = +25 C, conforming (human body model) to JESD22-A114 All 2 2000 V VESD(CDM) Electrostatic discharge voltage TA = +25 C, conforming (charge device model) to ANSI/ESD STM5.3.1 All C3 250 V 1. Data based on characterization results, not tested in production. Static latch-up Two complementary static tests are required on six parts to assess the latch-up performance: * A supply overvoltage is applied to each power supply pin. * A current injection is applied to each input, output and configurable I/O pin. These tests are compliant with EIA/JESD 78A IC latch-up standard. Table 46. Electrical sensitivities Symbol LU 6.3.13 Parameter Static latch-up class Conditions TA = +105 C conforming to JESD78A Class II level A I/O current injection characteristics As a general rule, current injection to the I/O pins, due to external voltage below VSS or above VDDIOx (for standard, 3.3 V-capable I/O pins) should be avoided during normal product operation. However, in order to give an indication of the robustness of the microcontroller in cases when abnormal injection accidentally happens, susceptibility tests are performed on a sample basis during device characterization. Functional susceptibility to I/O current injection While a simple application is executed on the device, the device is stressed by injecting current into the I/O pins programmed in floating input mode. While current is injected into the I/O pin, one at a time, the device is checked for functional failures. The failure is indicated by an out of range parameter: ADC error above a certain limit (higher than 5 LSB TUE), out of conventional limits of induced leakage current on adjacent pins (out of the -5 A/+0 A range) or other functional failure (for example reset occurrence or oscillator frequency deviation). The characterization results are given in Table 47. Negative induced leakage current is caused by negative injection and positive induced leakage current is caused by positive injection. DocID022265 Rev 6 69/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 Table 47. I/O current injection susceptibility Functional susceptibility Symbol Description Unit Negative Positive injection injection IINJ 6.3.14 Injected current on BOOT0 -0 NA Injected current on PA10, PA12, PB4, PB5, PB10, PB15 and PD2 pins with induced leakage current on adjacent pins less than -10 A -5 NA Injected current on all other FT and FTf pins -5 NA Injected current on PA6 and PC0 -0 +5 Injected current on all other TTa, TC and RST pins -5 +5 mA I/O port characteristics General input/output characteristics Unless otherwise specified, the parameters given in Table 48 are derived from tests performed under the conditions summarized in Table 20: General operating conditions. All I/Os are designed as CMOS- and TTL-compliant (except BOOT0). Table 48. I/O static characteristics Symbol VIL VIH Vhys Parameter Low level input voltage High level input voltage Schmitt trigger hysteresis Conditions Min Typ Max TC and TTa I/O - - 0.3 VDDIOx+0.07(1) FT and FTf I/O - - 0.475 VDDIOx-0.2(1) BOOT0 - - 0.3 VDDIOx-0.3(1) All I/Os except BOOT0 pin - - 0.3 VDDIOx TC and TTa I/O 0.445 VDDIOx+0.398(1) - - - - - - FT and FTf I/O (1) 0.2 VDDIOx+0.95 BOOT0 All I/Os except BOOT0 pin 0.7 VDDIOx - TC and TTa I/O - 200(1) - - (1) 100 - - 300(1) - FT and FTf I/O BOOT0 70/121 0.5 VDDIOx +0.2(1) DocID022265 Rev 6 Unit V V mV STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics Table 48. I/O static characteristics (continued) Symbol Ilkg RPU Parameter Input leakage current(2) Weak pull-up equivalent resistor (3) RPD Weak pull-down equivalent resistor(3) CIO I/O pin capacitance Conditions Min Typ Max TC, FT and FTf I/O TTa in digital mode VSS VIN VDDIOx - - 0.1 TTa in digital mode VDDIOx VIN VDDA - - 1 TTa in analog mode VSS VIN VDDA - - 0.2 FT and FTf I/O VDDIOx VIN 5 V - - 10 VIN = VSS 25 40 55 k VIN = VDDIOx 25 40 55 k - 5 - pF - Unit A 1. Data based on design simulation only. Not tested in production. 2. The leakage could be higher than the maximum value, if negative current is injected on adjacent pins. Refer to Table 47: I/O current injection susceptibility. 3. Pull-up and pull-down resistors are designed with a true resistance in series with a switchable PMOS/NMOS. This PMOS/NMOS contribution to the series resistance is minimal (~10% order). All I/Os are CMOS- and TTL-compliant (no software configuration required). Their characteristics cover more than the strict CMOS-technology or TTL parameters. The coverage of these requirements is shown in Figure 21 for standard I/Os, and in Figure 22 for 5 V tolerant I/Os. The following curves are design simulation results, not tested in production. DocID022265 Rev 6 71/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 Figure 21. TC and TTa I/O input characteristics 7(67('5$1*( 77/VWDQGDUGUHTXLUHPHQW HQW LUHP HTX DUGU QG 6VWD 2 &0 9,1 9 9 [ '',2 9 ,+PLQ 81'(),1(',13875$1*( ',2[ 9' 9,+PLQ 9'',2[ 9,/PD[ XLUHPHQW WDQGDUGUHT V 6 2 0 & 9'',2[ 9,/PD[ 77/VWDQGDUGUHTXLUHPHQW 7(67('5$1*( 9'',2[ 9 06Y9 Figure 22. Five volt tolerant (FT and FTf) I/O input characteristics 7(67('5$1*( 77/VWDQGDUGUHTXLUHPHQW HQW LUHP 9,1 9 9 9 ,+PLQ 81'(),1(',13875$1*( '',2[ 9 9,/PD[ QG 6VWD &02 [ '',2 9 9,+PLQ HTX DUGU '',2[ 77/VWDQGDUGUHTXLUHPHQW XLUHPHQW QGDUGUHT WD &026V [ 9'',2 9,/PD[ 7(67('5$1*( 9'',2[ 9 06Y9 72/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics Output driving current The GPIOs (general purpose input/outputs) can sink or source up to +/-8 mA, and sink or source up to +/- 20 mA (with a relaxed VOL/VOH). In the user application, the number of I/O pins which can drive current must be limited to respect the absolute maximum rating specified in Section 6.2: * The sum of the currents sourced by all the I/Os on VDDIOx, plus the maximum consumption of the MCU sourced on VDD, cannot exceed the absolute maximum rating IVDD (see Table 17: Voltage characteristics). * The sum of the currents sunk by all the I/Os on VSS, plus the maximum consumption of the MCU sunk on VSS, cannot exceed the absolute maximum rating IVSS (see Table 17: Voltage characteristics). Output voltage levels Unless otherwise specified, the parameters given in the table below are derived from tests performed under the ambient temperature and supply voltage conditions summarized in Table 20: General operating conditions. All I/Os are CMOS- and TTL-compliant (FT, TTa or TC unless otherwise specified). Table 49. Output voltage characteristics(1) Symbol Parameter VOL Output low level voltage for an I/O pin VOH Output high level voltage for an I/O pin VOL Output low level voltage for an I/O pin VOH Output high level voltage for an I/O pin VOL(3) Output low level voltage for an I/O pin VOH(3) Output high level voltage for an I/O pin VOL(3) Output low level voltage for an I/O pin VOH(3) Output high level voltage for an I/O pin VOLFm+(3) Output low level voltage for an FTf I/O pin in Fm+ mode Conditions Min Max CMOS port(2) |IIO| = 8 mA VDDIOx 2.7 V - 0.4 VDDIOx-0.4 - - 0.4 2.4 - - 1.3 VDDIOx-1.3 - - 0.4 VDDIOx-0.4 - |IIO| = 20 mA VDDIOx 2.7 V - 0.4 V |IIO| = 10 mA - 0.4 V TTL port(2) |IIO| = 8 mA VDDIOx 2.7 V |IIO| = 20 mA VDDIOx 2.7 V |IIO| = 6 mA Unit V V V V 1. The IIO current sourced or sunk by the device must always respect the absolute maximum rating specified in Table 17: Voltage characteristics, and the sum of the currents sourced or sunk by all the I/Os (I/O ports and control pins) must always respect the absolute maximum ratings IIO. 2. TTL and CMOS outputs are compatible with JEDEC standards JESD36 and JESD52. 3. Data based on characterization results. Not tested in production. DocID022265 Rev 6 73/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 Input/output AC characteristics The definition and values of input/output AC characteristics are given in Figure 23 and Table 50, respectively. Unless otherwise specified, the parameters given are derived from tests performed under the ambient temperature and supply voltage conditions summarized in Table 20: General operating conditions. Table 50. I/O AC characteristics(1)(2) OSPEEDRy [1:0] value(1) Symbol Parameter Conditions Min Max Unit - 2 MHz - 125 - 125 - 10 - 25 - 25 CL = 30 pF, VDDIOx 2.7 V - 50 fmax(IO)out Maximum frequency(3) CL = 50 pF, VDDIOx 2.7 V - 30 CL = 50 pF, VDDIOx < 2.7 V - 20 CL = 30 pF, VDDIOx 2.7 V - 5 CL = 50 pF, VDDIOx 2.7 V - 8 CL = 50 pF, VDDIOx < 2.7 V - 12 CL = 30 pF, VDDIOx 2.7 V - 5 CL = 50 pF, VDDIOx 2.7 V - 8 CL = 50 pF, VDDIOx < 2.7 V - 12 - 2 - 12 - 34 10 - fmax(IO)out Maximum frequency(3) x0 tf(IO)out Output fall time tr(IO)out Output rise time CL = 50 pF fmax(IO)out Maximum frequency(3) 01 11 tf(IO)out Output fall time tr(IO)out Output rise time tf(IO)out tr(IO)out Fm+ configuration (4) Output fall time Output rise time CL = 50 pF fmax(IO)out Maximum frequency(3) tf(IO)out Output fall time tr(IO)out Output rise time tEXTIpw Pulse width of external signals detected by the EXTI controller CL = 50 pF ns MHz ns MHz ns MHz ns ns 1. The I/O speed is configured using the OSPEEDRx[1:0] bits. Refer to the STM32F0xxxx RM0091 reference manual for a description of GPIO Port configuration register. 2. Guaranteed by design, not tested in production. 3. The maximum frequency is defined in Figure 23. 4. When Fm+ configuration is set, the I/O speed control is bypassed. Refer to the STM32F0xxxx reference manual RM0091 for a detailed description of Fm+ I/O configuration. 74/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics Figure 23. I/O AC characteristics definition W I ,2 RXW W U ,2 RXW 7 0D[LPXPIUHTXHQF\LVDFKLHYHGLI WW U I 7DQGLIWKHGXW\F\FOHLV ZKHQORDGHGE\& - VHHWKHWDEOH,2$&FKDUDFWHULVWLFVGHILQLWLRQ 069 6.3.15 NRST pin characteristics The NRST pin input driver uses the CMOS technology. It is connected to a permanent pullup resistor, RPU. Unless otherwise specified, the parameters given in the table below are derived from tests performed under the ambient temperature and supply voltage conditions summarized in Table 20: General operating conditions. Table 51. NRST pin characteristics Symbol Parameter Conditions Min Typ Max Unit VIL(NRST) NRST input low level voltage - - - 0.3 VDD+0.07(1) VIH(NRST) NRST input high level voltage - 0.445 VDD+0.398(1) - - Vhys(NRST) NRST Schmitt trigger voltage hysteresis - - 200 - mV V RPU Weak pull-up equivalent resistor(2) VIN = VSS 25 40 55 k VF(NRST) NRST input filtered pulse - - - 100(1) ns 2.7 < VDD < 3.6 300(3) - - 2.0 < VDD < 3.6 (3) - - VNF(NRST) NRST input not filtered pulse 500 ns 1. Data based on design simulation only. Not tested in production. 2. The pull-up is designed with a true resistance in series with a switchable PMOS. This PMOS contribution to the series resistance is minimal (~10% order). 3. Data based on design simulation only. Not tested in production. DocID022265 Rev 6 75/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 Figure 24. Recommended NRST pin protection ([WHUQDO UHVHWFLUFXLW 9 '' 1567 5 38 ,QWHUQDOUHVHW )LOWHU ) 069 1. The external capacitor protects the device against parasitic resets. 2. The user must ensure that the level on the NRST pin can go below the VIL(NRST) max level specified in Table 51: NRST pin characteristics. Otherwise the reset will not be taken into account by the device. 6.3.16 12-bit ADC characteristics Unless otherwise specified, the parameters given in Table 52 are derived from tests performed under the conditions summarized in Table 20: General operating conditions. Note: It is recommended to perform a calibration after each power-up. Table 52. ADC characteristics Symbol Parameter Conditions Min Typ Max Unit VDDA Analog supply voltage for ADC ON - 2.4 - 3.6 V VDDA = 3.3 V - 0.9 - mA - 0.6 - 14 MHz Sampling rate 12-bit resolution 0.043 - 1 MHz External trigger frequency fADC = 14 MHz, 12-bit resolution - - 823 kHz 12-bit resolution - - 17 1/fADC IDDA (ADC) fADC (2) fS fTRIG(2) Current consumption of the ADC(1) ADC clock frequency VAIN Conversion voltage range - 0 - VDDA V RAIN(2) External input impedance See Equation 1 and Table 53 for details - - 50 k RADC(2) Sampling switch resistance - - - 1 k CADC(2) Internal sample and hold capacitor - - - 8 pF tCAL(2)(3) Calibration time 76/121 fADC = 14 MHz 5.9 s - 83 1/fADC DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics Table 52. ADC characteristics (continued) Symbol Parameter WLATENCY(2)(4) tlatr (2) ADC_DR register ready latency Conditions Min Typ Max ADC clock = HSI14 1.5 ADC cycles + 2 fPCLK cycles - 1.5 ADC cycles + 3 fPCLK cycles ADC clock = PCLK/2 - 4.5 - fPCLK cycle ADC clock = PCLK/4 - 8.5 - fPCLK cycle fADC = fPCLK/2 = 14 MHz 0.196 s fADC = fPCLK/2 5.5 1/fPCLK 0.219 s 10.5 1/fPCLK Trigger conversion latency fADC = fPCLK/4 = 12 MHz fADC = fPCLK/4 JitterADC tS(2) fADC = fHSI14 = 14 MHz 0.179 - 0.250 s fADC = fHSI14 - 1 - 1/fHSI14 fADC = 14 MHz 0.107 - 17.1 s - 1.5 - 239.5 1/fADC ADC jitter on trigger conversion Sampling time tSTAB(2) Stabilization time tCONV(2) Total conversion time (including sampling time) Unit fADC = 14 MHz, 12-bit resolution 12-bit resolution 14 1 1/fADC - 18 14 to 252 (tS for sampling +12.5 for successive approximation) s 1/fADC 1. During conversion of the sampled value (12.5 x ADC clock period), an additional consumption of 100 A on IDDA and 60 A on IDD should be taken into account. 2. Guaranteed by design, not tested in production. 3. Specified value includes only ADC timing. It does not include the latency of the register access. 4. This parameter specify latency for transfer of the conversion result to the ADC_DR register. EOC flag is set at this time. Equation 1: RAIN max formula TS - - R ADC R AIN < --------------------------------------------------------------N+2 f ADC x C ADC x ln ( 2 ) The formula above (Equation 1) is used to determine the maximum external impedance allowed for an error below 1/4 of LSB. Here N = 12 (from 12-bit resolution). Table 53. RAIN max for fADC = 14 MHz Ts (cycles) tS (s) RAIN max (k)(1) 1.5 0.11 0.4 7.5 0.54 5.9 13.5 0.96 11.4 DocID022265 Rev 6 77/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 Table 53. RAIN max for fADC = 14 MHz (continued) Ts (cycles) tS (s) RAIN max (k)(1) 28.5 2.04 25.2 41.5 2.96 37.2 55.5 3.96 50 71.5 5.11 NA 239.5 17.1 NA 1. Guaranteed by design, not tested in production. Table 54. ADC accuracy(1)(2)(3) Symbol Parameter Test conditions Typ Max(4) 1.3 2 1 1.5 0.5 1.5 0.7 1 ET Total unadjusted error EO Offset error EG Gain error ED Differential linearity error EL Integral linearity error 0.8 1.5 ET Total unadjusted error 3.3 4 EO Offset error 1.9 2.8 EG Gain error 2.8 3 ED Differential linearity error 0.7 1.3 EL Integral linearity error 1.2 1.7 ET Total unadjusted error 3.3 4 1.9 2.8 2.8 3 0.7 1.3 1.2 1.7 EO Offset error EG Gain error ED Differential linearity error EL Integral linearity error fPCLK = 48 MHz, fADC = 14 MHz, RAIN < 10 k VDDA = 3 V to 3.6 V TA = 25 C fPCLK = 48 MHz, fADC = 14 MHz, RAIN < 10 k VDDA = 2.7 V to 3.6 V TA = - 40 to 105 C fPCLK = 48 MHz, fADC = 14 MHz, RAIN < 10 k VDDA = 2.4 V to 3.6 V TA = 25 C Unit LSB LSB LSB 1. ADC DC accuracy values are measured after internal calibration. 2. ADC Accuracy vs. Negative Injection Current: Injecting negative current on any of the standard (non-robust) analog input pins should be avoided as this significantly reduces the accuracy of the conversion being performed on another analog input. It is recommended to add a Schottky diode (pin to ground) to standard analog pins which may potentially inject negative current. Any positive injection current within the limits specified for IINJ(PIN) and IINJ(PIN) in Section 6.3.14 does not affect the ADC accuracy. 3. Better performance may be achieved in restricted VDDA, frequency and temperature ranges. 4. Data based on characterization results, not tested in production. 78/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics Figure 25. ADC accuracy characteristics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igure 26. Typical connection diagram using the ADC 9''$ 6DPSOHDQGKROG$'& FRQYHUWHU 97 5$,1 9$,1 5$'& $,1[ &SDUDVLWLF 97 ,/ $ ELW FRQYHUWHU &$'& 069 1. Refer to Table 52: ADC characteristics for the values of RAIN, RADC and CADC. 2. Cparasitic represents the capacitance of the PCB (dependent on soldering and PCB layout quality) plus the pad capacitance (roughly 7 pF). A high Cparasitic value will downgrade conversion accuracy. To remedy this, fADC should be reduced. General PCB design guidelines Power supply decoupling should be performed as shown in Figure 13: Power supply scheme. The 10 nF capacitor should be ceramic (good quality) and it should be placed as close as possible to the chip. DocID022265 Rev 6 79/121 90 Electrical characteristics 6.3.17 STM32F051x4 STM32F051x6 STM32F051x8 DAC electrical specifications Table 55. DAC characteristics Symbol Parameter Min Typ Max Unit Comments VDDA Analog supply voltage for DAC ON 2.4 - 3.6 V RLOAD(1) Resistive load with buffer ON 5 - - k Load is referred to ground RO(1) CLOAD(1) Impedance output with buffer OFF - - 15 k When the buffer is OFF, the Minimum resistive load between DAC_OUT and VSS to have a 1% accuracy is 1.5 M Capacitive load - - 50 pF Maximum capacitive load at DAC_OUT pin (when the buffer is ON). It gives the maximum output excursion of the DAC. It corresponds to 12-bit input code (0x0E0) to (0xF1C) at VDDA = 3.6 V and (0x155) and (0xEAB) at VDDA = 2.4 V DAC_OUT min(1) Lower DAC_OUT voltage with buffer ON 0.2 - - V DAC_OUT max(1) Higher DAC_OUT voltage with buffer ON - - VDDA - 0.2 V DAC_OUT min(1) Lower DAC_OUT voltage with buffer OFF - 0.5 - mV DAC_OUT max(1) Higher DAC_OUT voltage with buffer OFF - - VDDA - 1LSB V - - 600 A IDDA(1) DAC DC current consumption in quiescent mode(2) With no load, middle code (0x800) on the input - - 700 A With no load, worst code (0xF1C) on the input Differential non linearity Difference between two consecutive code-1LSB) - - 0.5 LSB Given for the DAC in 10-bit configuration - - 2 LSB Given for the DAC in 12-bit configuration - - 1 LSB Given for the DAC in 10-bit configuration - - 4 LSB Given for the DAC in 12-bit configuration - - 10 mV - - 3 LSB Given for the DAC in 10-bit at VDDA = 3.6 V - - 12 LSB Given for the DAC in 12-bit at VDDA = 3.6 V - - 0.5 % DNL(3) INL(3) Offset(3) Integral non linearity (difference between measured value at Code i and the value at Code i on a line drawn between Code 0 and last Code 1023) Offset error (difference between measured value at Code (0x800) and the ideal value = VDDA/2) Gain error(3) Gain error 80/121 DocID022265 Rev 6 It gives the maximum output excursion of the DAC. Given for the DAC in 12-bit configuration STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics Table 55. DAC characteristics (continued) Symbol Min Typ Max Unit Settling time (full scale: for a 10-bit input code transition between the lowest and the (3) tSETTLING highest input codes when DAC_OUT reaches final value 1LSB - 3 4 s Max frequency for a correct DAC_OUT change when small variation in the input code (from code i to i+1LSB) - - 1 tWAKEUP(3) Wakeup time from off state (Setting the ENx bit in the DAC Control register) - 6.5 10 s CLOAD 50 pF, RLOAD 5 k input code between lowest and highest possible ones. PSRR+ (1) Power supply rejection ratio (to VDDA) (static DC measurement - -67 -40 dB No RLOAD, CLOAD = 50 pF Update rate(3) Parameter Comments CLOAD 50 pF, RLOAD 5 k MS/s CLOAD 50 pF, RLOAD 5 k 1. Guaranteed by design, not tested in production. 2. The DAC is in "quiescent mode" when it keeps the value steady on the output so no dynamic consumption is involved. 3. Data based on characterization results, not tested in production. Figure 27. 12-bit buffered / non-buffered DAC %XIIHUHG1RQEXIIHUHG'$& %XIIHU 5/ ELWGLJLWDO WRDQDORJ FRQYHUWHU '$&B287[ &/ 069 1. The DAC integrates an output buffer that can be used to reduce the output impedance and to drive external loads directly without the use of an external operational amplifier. The buffer can be bypassed by configuring the BOFFx bit in the DAC_CR register. DocID022265 Rev 6 81/121 90 Electrical characteristics 6.3.18 STM32F051x4 STM32F051x6 STM32F051x8 Comparator characteristics Table 56. Comparator characteristics Symbol Parameter Conditions Min(1) Typ Max(1) Analog supply voltage - VDD - 3.6 VIN Comparator input voltage range - 0 - VDDA VSC VREFINT scaler offset voltage - - 5 10 tS_SC VREFINT scaler startup time from power down First VREFINT scaler activation after device power on - - Next activations - - 0.2 Startup time to reach propagation delay specification - - 60 Ultra-low power mode - 2 4.5 Low power mode - 0.7 1.5 Medium power mode - 0.3 0.6 - 50 100 - 100 240 Ultra-low power mode - 2 7 Low power mode - 0.7 2.1 Medium power mode - 0.3 1.2 - 90 180 - 110 300 VDDA tSTART Comparator startup time Propagation delay for 200 mV step with 100 mV overdrive High speed mode tD Propagation delay for full range step with 100 mV overdrive High speed mode VDDA 2.7 V VDDA < 2.7 V VDDA 2.7 V VDDA < 2.7 V Unit V mV 1000 (2) ms s s ns s ns Voffset Comparator offset error - 4 10 mV dVoffset/dT Offset error temperature coefficient - 18 - V/C Ultra-low power mode - 1.2 1.5 Low power mode - 3 5 Medium power mode - 10 15 High speed mode - 75 100 IDD(COMP) 82/121 COMP current consumption DocID022265 Rev 6 A STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics Table 56. Comparator characteristics (continued) Symbol Parameter Min(1) Typ Max(1) Conditions No hysteresis (COMPxHYST[1:0]=00) Vhys Comparator hysteresis - High speed mode Low hysteresis (COMPxHYST[1:0]=01) All other power modes 3 High speed mode Medium hysteresis (COMPxHYST[1:0]=10) All other power modes 7 High speed mode High hysteresis (COMPxHYST[1:0]=11) All other power modes 18 5 9 19 0 Unit 13 8 10 26 15 mV 19 49 31 40 1. Data based on characterization results, not tested in production. 2. For more details and conditions see Figure 28: Maximum VREFINT scaler startup time from power down. Figure 28. Maximum VREFINT scaler startup time from power down DocID022265 Rev 6 83/121 90 Electrical characteristics 6.3.19 STM32F051x4 STM32F051x6 STM32F051x8 Temperature sensor characteristics Table 57. TS characteristics Symbol Parameter TL(1) Avg_Slope Min Typ Max Unit - 1 2 C 4.0 4.3 4.6 mV/C 1.34 1.43 1.52 V VSENSE linearity with temperature (1) V30 Average slope Voltage at 30 C ( 5 C) (2) tSTART(1) ADC_IN16 buffer startup time - - 10 s tS_temp(1) ADC sampling time when reading the temperature 4 - - s 1. Guaranteed by design, not tested in production. 2. Measured at VDDA = 3.3 V 10 mV. The V30 ADC conversion result is stored in the TS_CAL1 byte. Refer to Table 3: Temperature sensor calibration values. 6.3.20 VBAT monitoring characteristics Table 58. VBAT monitoring characteristics Symbol Parameter Min Typ Max Unit k R Resistor bridge for VBAT - 2 x 50 - Q Ratio on VBAT measurement - 2 - Error on Q -1 - +1 % ADC sampling time when reading the VBAT 4 - - s Er(1) tS_vbat(1) 1. Guaranteed by design, not tested in production. 6.3.21 Timer characteristics The parameters given in the following tables are guaranteed by design. Refer to Section 6.3.14: I/O port characteristics for details on the input/output alternate function characteristics (output compare, input capture, external clock, PWM output). Table 59. TIMx characteristics Symbol Parameter tres(TIM) Timer resolution time fEXT Timer external clock frequency on CH1 to CH4 16-bit timer maximum period tMAX_COUNT 32-bit counter maximum period 84/121 Conditions Min Typ Max Unit - - 1 - tTIMxCLK fTIMxCLK = 48 MHz - 20.8 - ns - - fTIMxCLK/2 - MHz fTIMxCLK = 48 MHz - 24 - MHz - - 216 - tTIMxCLK fTIMxCLK = 48 MHz - 1365 - s - - 232 - tTIMxCLK fTIMxCLK = 48 MHz - 89.48 - s DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics Table 60. IWDG min/max timeout period at 40 kHz (LSI)(1) Prescaler divider PR[2:0] bits Min timeout RL[11:0]= 0x000 Max timeout RL[11:0]= 0xFFF /4 0 0.1 409.6 /8 1 0.2 819.2 /16 2 0.4 1638.4 /32 3 0.8 3276.8 /64 4 1.6 6553.6 /128 5 3.2 13107.2 /256 6 or 7 6.4 26214.4 Unit ms 1. These timings are given for a 40 kHz clock but the microcontroller internal RC frequency can vary from 30 to 60 kHz. Moreover, given an exact RC oscillator frequency, the exact timings still depend on the phasing of the APB interface clock versus the LSI clock so that there is always a full RC period of uncertainty. Table 61. WWDG min/max timeout value at 48 MHz (PCLK) 6.3.22 Prescaler WDGTB Min timeout value Max timeout value 1 0 0.0853 5.4613 2 1 0.1706 10.9226 4 2 0.3413 21.8453 8 3 0.6826 43.6906 Unit ms Communication interfaces I2C interface characteristics The I2C interface meets the timings requirements of the I2C-bus specification and user manual rev. 03 for: * Standard-mode (Sm): with a bit rate up to 100 kbit/s * Fast-mode (Fm): with a bit rate up to 400 kbit/s * Fast-mode Plus (Fm+): with a bit rate up to 1 Mbit/s. The I2C timings requirements are guaranteed by design when the I2Cx peripheral is properly configured (refer to Reference manual). The SDA and SCL I/O requirements are met with the following restrictions: the SDA and SCL I/O pins are not "true" open-drain. When configured as open-drain, the PMOS connected between the I/O pin and VDDIOx is disabled, but is still present. Only FTf I/O pins support Fm+ low level output current maximum requirement. Refer to Section 6.3.14: I/O port characteristics for the I2C I/Os characteristics. All I2C SDA and SCL I/Os embed an analog filter. Refer to the table below for the analog filter characteristics: DocID022265 Rev 6 85/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 Table 62. I2C analog filter characteristics(1) Symbol tAF Parameter Maximum width of spikes that are suppressed by the analog filter Min Max Unit 50(2) 260(3) ns 1. Guaranteed by design, not tested in production. 2. Spikes with widths below tAF(min) are filtered. 3. Spikes with widths above tAF(max) are not filtered SPI/I2S characteristics Unless otherwise specified, the parameters given in Table 63 for SPI or in Table 64 for I2S are derived from tests performed under the ambient temperature, fPCLKx frequency and supply voltage conditions summarized in Table 20: General operating conditions. Refer to Section 6.3.14: I/O port characteristics for more details on the input/output alternate function characteristics (NSS, SCK, MOSI, MISO for SPI and WS, CK, SD for I2S). Table 63. SPI characteristics(1) Symbol fSCK 1/tc(SCK) Parameter SPI clock frequency Conditions Min Max Master mode - 18 Slave mode - 18 - 6 tr(SCK) tf(SCK) SPI clock rise and fall time Capacitive load: C = 15 pF tsu(NSS) NSS setup time Slave mode 4Tpclk - th(NSS) NSS hold time Slave mode 2Tpclk + 10 - SCK high and low time Master mode, fPCLK = 36 MHz, presc = 4 Tpclk/2 -2 Tpclk/2 + 1 Master mode 4 - Slave mode 5 - Master mode 4 - Slave mode 5 - Data output access time Slave mode, fPCLK = 20 MHz 0 3Tpclk Data output disable time Slave mode 0 18 tv(SO) Data output valid time Slave mode (after enable edge) - 22.5 tv(MO) Data output valid time Master mode (after enable edge) - 6 Slave mode (after enable edge) 11.5 - Master mode (after enable edge) 2 - Slave mode 25 75 tw(SCKH) tw(SCKL) tsu(MI) tsu(SI) th(MI) th(SI) ta(SO)(2) tdis(SO) (3) th(SO) th(MO) DuCy(SCK) Data input setup time Data input hold time Data output hold time SPI slave input clock duty cycle Unit MHz ns ns % 1. Data based on characterization results, not tested in production. 2. Min time is for the minimum time to drive the output and the max time is for the maximum time to validate the data. 3. Min time is for the minimum time to invalidate the output and the max time is for the maximum time to put the data in Hi-Z 86/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics Figure 29. SPI timing diagram - slave mode and CPHA = 0 166LQSXW 6&.,QSXW W68 166 &3+$ &32/ &3+$ &32/ WK 166 WF 6&. WZ 6&.+ WZ 6&./ W9 62 WD 62 0,62 287387 WU 6&. WI 6&. WK 62 06%287 %,7287 06%,1 %,7,1 WGLV 62 /6%287 WVX 6, 026, ,1387 /6%,1 WK 6, DLF Figure 30. SPI timing diagram - slave mode and CPHA = 1 166LQSXW 6&.LQSXW W68 166 &3+$ &32/ &3+$ &32/ WZ 6&.+ WZ 6&./ WK 62 WY 62 WD 62 0,62 287387 06%287 %,7287 WU 6&. WI 6&. WGLV 62 /6%287 WK 6, WVX 6, 026, ,1387 WK 166 WF 6&. 06%,1 %,7,1 /6%,1 DLE 1. Measurement points are done at CMOS levels: 0.3 VDD and 0.7 VDD. DocID022265 Rev 6 87/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 Figure 31. SPI timing diagram - master mode +LJK 166LQSXW 6&.2XWSXW &3+$ &32/ 6&.2XWSXW WF 6&. &3+$ &32/ &3+$ &32/ &3+$ &32/ WZ 6&.+ WZ 6&./ WVX 0, 0,62 ,13 87 WU 6&. WI 6&. %,7,1 06%,1 /6%,1 WK 0, 026, 287387 % , 7287 06%287 WY 02 /6%287 WK 02 DLF 1. Measurement points are done at CMOS levels: 0.3 VDD and 0.7 VDD. Table 64. I2S characteristics(1) Symbol fCK 1/tc(CK) Parameter I2S clock frequency Conditions Master mode (data: 16 bits, Audio frequency = 48 kHz) Slave mode tr(CK) I2S clock rise time tf(CK) I2S clock fall time Capacitive load CL = 15 pF Min Max 1.597 1.601 0 6.5 - 10 - 12 306 - 312 - tw(CKH) I2S tw(CKL) 2 I S clock low time Master fPCLK= 16 MHz, audio frequency = 48 kHz tv(WS) WS valid time Master mode 2 - th(WS) WS hold time Master mode 2 - tsu(WS) WS setup time Slave mode 7 - th(WS) WS hold time Slave mode 0 - Slave mode 25 75 DuCy(SCK) 88/121 I2S clock high time slave input clock duty cycle DocID022265 Rev 6 Unit MHz ns % STM32F051x4 STM32F051x6 STM32F051x8 Electrical characteristics Table 64. I2S characteristics(1) (continued) Symbol tsu(SD_MR) tsu(SD_SR) th(SD_MR) th(SD_SR) Parameter Data input setup time (2) (2) tv(SD_MT)(2) tv(SD_ST)(2) th(SD_MT) th(SD_ST) Data input hold time Data output valid time Data output hold time Conditions Min Max Master receiver 6 - Slave receiver 2 - Master receiver 4 - Slave receiver 0.5 - Master transmitter - 4 Slave transmitter - 20 Master transmitter 0 - Slave transmitter 13 - Unit ns 1. Data based on design simulation and/or characterization results, not tested in production. 2. Depends on fPCLK. For example, if fPCLK = 8 MHz, then TPCLK = 1/fPLCLK = 125 ns. Figure 32. I2S slave timing diagram (Philips protocol) &.,QSXW WF &. &32/ &32/ WZ &.+ WK :6 WZ &./ :6LQSXW WY 6'B67 WVX :6 6'WUDQVPLW /6%WUDQVPLW 06%WUDQVPLW WVX 6'B65 6'UHFHLYH /6%UHFHLYH WK 6'B67 %LWQWUDQVPLW WK 6'B65 06%UHFHLYH %LWQUHFHLYH /6%UHFHLYH 06Y9 1. Measurement points are done at CMOS levels: 0.3 x VDDIOx and 0.7 x VDDIOx. 2. LSB transmit/receive of the previously transmitted byte. No LSB transmit/receive is sent before the first byte. DocID022265 Rev 6 89/121 90 Electrical characteristics STM32F051x4 STM32F051x6 STM32F051x8 Figure 33. I2S master timing diagram (Philips protocol) WI &. WU &. &.RXWSXW WF &. &32/ WZ &.+ &32/ WY :6 WK :6 WZ &./ :6RXWSXW WY 6'B07 6'WUDQVPLW /6%WUDQVPLW 06%WUDQVPLW /6%UHFHLYH /6%WUDQVPLW WK 6'B05 WVX 6'B05 6'UHFHLYH %LWQWUDQVPLW WK 6'B07 06%UHFHLYH %LWQUHFHLYH /6%UHFHLYH 06Y9 1. Data based on characterization results, not tested in production. 2. LSB transmit/receive of the previously transmitted byte. No LSB transmit/receive is sent before the first byte. 90/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 7 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. 7.1 UFBGA64 package information UFBGA64 is a 64-ball, 5 x 5 mm, 0.5 mm pitch ultra-fine-profile ball grid array package. Figure 34. UFBGA64 package outline = 6HDWLQJSODQH GGG = $ $ $ $ $ ( H $EDOO $EDOO LGHQWLILHU LQGH[DUHD ) ; ( $ ) ' ' H < + %277209,(: E EDOOV HHH 0 = < ; III 0 = 7239,(: $B0(B9 1. Drawing is not to scale. Table 65. UFBGA64 package mechanical data inches(1) millimeters Symbol Min Typ Max Min Typ Max A 0.460 0.530 0.600 0.0181 0.0209 0.0236 A1 0.050 0.080 0.110 0.0020 0.0031 0.0043 A2 0.400 0.450 0.500 0.0157 0.0177 0.0197 A3 0.080 0.130 0.180 0.0031 0.0051 0.0071 A4 0.270 0.320 0.370 0.0106 0.0126 0.0146 DocID022265 Rev 6 91/121 115 Package information STM32F051x4 STM32F051x6 STM32F051x8 Table 65. UFBGA64 package mechanical data (continued) inches(1) millimeters Symbol Min Typ Max Min Typ Max A 0.460 0.530 0.600 0.0181 0.0209 0.0236 b 0.170 0.280 0.330 0.0067 0.0110 0.0130 D 4.850 5.000 5.150 0.1909 0.1969 0.2028 D1 3.450 3.500 3.550 0.1358 0.1378 0.1398 E 4.850 5.000 5.150 0.1909 0.1969 0.2028 E1 3.450 3.500 3.550 0.1358 0.1378 0.1398 e - 0.500 - - 0.0197 - F 0.700 0.750 0.800 0.0276 0.0295 0.0315 ddd - - 0.080 - - 0.0031 eee - - 0.150 - - 0.0059 fff - - 0.050 - - 0.0020 1. Values in inches are converted from mm and rounded to 4 decimal digits. Figure 35. Recommended footprint for UFBGA64 package 'SDG 'VP $B)3B9 Table 66. UFBGA64 recommended PCB design rules Dimension Recommended values Pitch 0.5 Dpad 0.280 mm Dsm 0.370 mm typ. (depends on the soldermask registration tolerance) Stencil opening 0.280 mm Stencil thickness Between 0.100 mm and 0.125 mm Pad trace width 0.100 mm Device marking The following figure gives an example of topside marking orientation versus ball A1 identifier location. 92/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Package information Figure 36. UFBGA64 package marking example 3URGXFW LGHQWLILFDWLRQ '3) 'DWHFRGH : 88 6WDQGDUG67ORJR 5HYLVLRQFRGH 3 %DOOLGHQWLILHU 069 1. Parts marked as "ES", "E" or accompanied by an Engineering Sample notification letter, are not yet qualified and therefore not yet ready to be used in production and any consequences deriving from such usage will not be at ST charge. In no event, ST will be liable for any customer usage of these engineering samples in production. ST Quality has to be contacted prior to any decision to use these Engineering Samples to run qualification activity. DocID022265 Rev 6 93/121 115 Package information 7.2 STM32F051x4 STM32F051x6 STM32F051x8 LQFP64 package information LQFP64 is a 64-pin, 10 x 10 mm low-profile quad flat package. Figure 37. LQFP64 package outline PP *$8*(3/$1( F $ $ $ 6($7,1*3/$1( & $ FFF & ' ' ' . / / ( ( ( E 3,1 ,'(17,),&$7,21 H :B0(B9 1. Drawing is not to scale. Table 67. LQFP64 package mechanical data inches(1) millimeters Symbol 94/121 Min Typ Max Min Typ Max A - - 1.600 - - 0.0630 A1 0.050 - 0.150 0.0020 - 0.0059 A2 1.350 1.400 1.450 0.0531 0.0551 0.0571 b 0.170 0.220 0.270 0.0067 0.0087 0.0106 c 0.090 - 0.200 0.0035 - 0.0079 D - 12.000 - - 0.4724 - D1 - 10.000 - - 0.3937 - D3 - 7.500 - - 0.2953 - E - 12.000 - - 0.4724 - E1 - 10.000 - - 0.3937 - DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Package information Table 67. LQFP64 package mechanical data (continued) inches(1) millimeters Symbol Min Typ Max Min Typ Max E3 - 7.500 - - 0.2953 - e - 0.500 - - 0.0197 - K 0 3.5 7 0 3.5 7 L 0.450 0.600 0.750 0.0177 0.0236 0.0295 L1 - 1.000 - - 0.0394 - ccc - - 0.080 - - 0.0031 1. Values in inches are converted from mm and rounded to 4 decimal digits. Figure 38. Recommended footprint for LQFP64 package AIC 1. Dimensions are expressed in millimeters. DocID022265 Rev 6 95/121 115 Package information STM32F051x4 STM32F051x6 STM32F051x8 Device marking The following figure gives an example of topside marking orientation versus pin 1 identifier location. Figure 39. LQFP64 package marking example 5HYLVLRQFRGH 5 3URGXFWLGHQWLILFDWLRQ 670) 57 'DWHFRGH z tt 3LQLGHQWLILHU 06Y9 1. Parts marked as "ES", "E" or accompanied by an Engineering Sample notification letter, are not yet qualified and therefore not yet ready to be used in production and any consequences deriving from such usage will not be at ST charge. In no event, ST will be liable for any customer usage of these engineering samples in production. ST Quality has to be contacted prior to any decision to use these Engineering Samples to run qualification activity. 96/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 LQFP48 package information LQFP48 is a 48-pin, 7 x 7 mm low-profile quad flat package. Figure 40. LQFP48 package outline 3%!4).' 0,!.% # C ! ! ! MM '!5'% 0,!.% CCC # $ + ! $ , , $ 0). )$%.4)&)#!4)/. % % B % 7.3 Package information E "?-%?6 1. Drawing is not to scale. DocID022265 Rev 6 97/121 115 Package information STM32F051x4 STM32F051x6 STM32F051x8 Table 68. LQFP48 package mechanical data inches(1) millimeters Symbol Min Typ Max Min Typ Max A - - 1.600 - - 0.0630 A1 0.050 - 0.150 0.0020 - 0.0059 A2 1.350 1.400 1.450 0.0531 0.0551 0.0571 b 0.170 0.220 0.270 0.0067 0.0087 0.0106 c 0.090 - 0.200 0.0035 - 0.0079 D 8.800 9.000 9.200 0.3465 0.3543 0.3622 D1 6.800 7.000 7.200 0.2677 0.2756 0.2835 D3 - 5.500 - - 0.2165 - E 8.800 9.000 9.200 0.3465 0.3543 0.3622 E1 6.800 7.000 7.200 0.2677 0.2756 0.2835 E3 - 5.500 - - 0.2165 - e - 0.500 - - 0.0197 - L 0.450 0.600 0.750 0.0177 0.0236 0.0295 L1 - 1.000 - - 0.0394 - k 0 3.5 7 0 3.5 7 ccc - - 0.080 - - 0.0031 1. Values in inches are converted from mm and rounded to 4 decimal digits. Figure 41. Recommended footprint for LQFP48 package AID 1. Dimensions are expressed in millimeters. 98/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Package information Device marking The following figure gives an example of topside marking orientation versus pin 1 identifier location. Figure 42. LQFP48 package marking example 3URGXFWLGHQWLILFDWLRQ 670) &7 'DWHFRGH 3LQLGHQWLILHU < :: 5HYLVLRQFRGH 5 06Y9 1. Parts marked as "ES", "E" or accompanied by an Engineering Sample notification letter, are not yet qualified and therefore not yet ready to be used in production and any consequences deriving from such usage will not be at ST charge. In no event, ST will be liable for any customer usage of these engineering samples in production. ST Quality has to be contacted prior to any decision to use these Engineering Samples to run qualification activity. DocID022265 Rev 6 99/121 115 Package information 7.4 STM32F051x4 STM32F051x6 STM32F051x8 UFQFPN48 package information UFQFPN48 is a 48-lead, 7x7 mm, 0.5 mm pitch, ultra-thin fine-pitch quad flat package. Figure 43. UFQFPN48 package outline 3LQLGHQWLILHU ODVHUPDUNLQJDUHD ' $ ( ( 7 GGG $ 6HDWLQJ SODQH E H 'HWDLO< ' ([SRVHGSDG DUHD < ' / &[ SLQFRUQHU ( 5W\S 'HWDLO= = $%B0(B9 1. Drawing is not to scale. 2. All leads/pads should also be soldered to the PCB to improve the lead/pad solder joint life. 3. There is an exposed die pad on the underside of the UFQFPN package. It is recommended to connect and solder this back-side pad to PCB ground. 100/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Package information Table 69. UFQFPN48 package mechanical data inches(1) millimeters Symbol Min Typ Max Min Typ Max A 0.500 0.550 0.600 0.0197 0.0217 0.0236 A1 0.000 0.020 0.050 0.0000 0.0008 0.0020 D 6.900 7.000 7.100 0.2717 0.2756 0.2795 E 6.900 7.000 7.100 0.2717 0.2756 0.2795 D2 5.500 5.600 5.700 0.2165 0.2205 0.2244 E2 5.500 5.600 5.700 0.2165 0.2205 0.2244 L 0.300 0.400 0.500 0.0118 0.0157 0.0197 T - 0.152 - - 0.0060 - b 0.200 0.250 0.300 0.0079 0.0098 0.0118 e - 0.500 - - 0.0197 - ddd - - 0.080 - - 0.0031 1. Values in inches are converted from mm and rounded to 4 decimal digits. Figure 44. Recommended footprint for UFQFPN48 package !"?&0?6 1. Dimensions are expressed in millimeters. DocID022265 Rev 6 101/121 115 Package information STM32F051x4 STM32F051x6 STM32F051x8 Device marking The following figure gives an example of topside marking orientation versus pin 1 identifier location. Figure 45. UFQFPN48 package marking example 3URGXFWLGHQWLILFDWLRQ 670) &8 'DWHFRGH 3LQLGHQWLILHU < :: 5HYLVLRQFRGH 5 06Y9 1. Parts marked as "ES", "E" or accompanied by an Engineering Sample notification letter, are not yet qualified and therefore not yet ready to be used in production and any consequences deriving from such usage will not be at ST charge. In no event, ST will be liable for any customer usage of these engineering samples in production. ST Quality has to be contacted prior to any decision to use these Engineering Samples to run qualification activity. 102/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 7.5 Package information WLCSP36 package information WLCSP36 is a 36-ball, 2.605 x 2.703 mm, 0.4 mm pitch wafer-level chip-scale package. Figure 46. WLCSP36 package outline H EEE = $EDOOORFDWLRQ ) H * $ 'HWDLO$ H H ) $ $ $ %XPSVLGH 6LGHYLHZ ; < $ %XPS $ RULHQWDWLRQ UHIHUHQFH HHH = DDD = $ E EDOOV FFF = ; < GGG = :DIHUEDFNVLGH E = 6HDWLQJSODQH 'HWDLO$ URWDWHG >Ds 1. Drawing is not to scale. Table 70. WLCSP36 package mechanical data inches(1) millimeters Symbol Min Typ Max Min Typ Max A 0.525 0.555 0.585 0.0207 0.0219 0.0230 A1 - 0.175 - - 0.0069 - A2 - 0.380 - - 0.0150 - A3(2) - 0.025 - - 0.0010 - (3) 0.220 0.250 0.280 0.0087 0.0098 0.0110 D 2.570 2.605 2.640 0.1012 0.1026 0.1039 E 2.668 2.703 2.738 0.1050 0.1064 0.1078 e - 0.400 - - 0.0157 - e1 - 2.000 - - 0.0787 - e2 - 2.000 - - 0.0787 - b DocID022265 Rev 6 103/121 115 Package information STM32F051x4 STM32F051x6 STM32F051x8 Table 70. WLCSP36 package mechanical data (continued) inches(1) millimeters Symbol Min Typ Max Min Typ Max F - 0.3025 - - 0.0119 - G - 0.3515 - - 0.0138 - aaa - - 0.100 - - 0.0039 bbb - - 0.100 - - 0.0039 ccc - - 0.100 - - 0.0039 ddd - - 0.050 - - 0.0020 eee - - 0.050 - - 0.0020 1. Values in inches are converted from mm and rounded to 4 decimal digits. 2. Back side coating. 3. Dimension is measured at the maximum bump diameter parallel to primary datum Z. Figure 47. Recommended pad footprint for WLCSP36 package 'SDG 'VP 069 Table 71. WLCSP36 recommended PCB design rules Dimension 104/121 Recommended values Pitch 0.4 mm Dpad 260 m max. (circular) 220 m recommended Dsm 300 m min. (for 260 m diameter pad) PCB pad design Non-solder mask defined via underbump allowed DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Package information Device marking The following figure gives an example of topside marking orientation versus ball A1 identifier location. Figure 48. WLCSP36 package marking example 'RW 3URGXFWLGHQWLILFDWLRQ ' 5HYLVLRQFRGH 3 'DWHFRGH : 88 069 1. Parts marked as "ES", "E" or accompanied by an Engineering Sample notification letter, are not yet qualified and therefore not yet ready to be used in production and any consequences deriving from such usage will not be at ST charge. In no event, ST will be liable for any customer usage of these engineering samples in production. ST Quality has to be contacted prior to any decision to use these Engineering Samples to run qualification activity. DocID022265 Rev 6 105/121 115 Package information 7.6 STM32F051x4 STM32F051x6 STM32F051x8 LQFP32 package information LQFP32 is a 32-pin, 7 x 7 mm low-profile quad flat package. Figure 49. LQFP32 package outline C ! ! ! 3%!4).' 0,!.% # MM CCC '!5'% 0,!.% # + $ , ! $ , $ 0). )$%.4)&)#!4)/. % E 1. Drawing is not to scale. 106/121 % % B DocID022265 Rev 6 7@.&@7 STM32F051x4 STM32F051x6 STM32F051x8 Package information Table 72. LQFP32 package mechanical data inches(1) millimeters Symbol Min Typ Max Min Typ Max A - - 1.600 - - 0.0630 A1 0.050 - 0.150 0.0020 - 0.0059 A2 1.350 1.400 1.450 0.0531 0.0551 0.0571 b 0.300 0.370 0.450 0.0118 0.0146 0.0177 c 0.090 - 0.200 0.0035 - 0.0079 D 8.800 9.000 9.200 0.3465 0.3543 0.3622 D1 6.800 7.000 7.200 0.2677 0.2756 0.2835 D3 - 5.600 - - 0.2205 - E 8.800 9.000 9.200 0.3465 0.3543 0.3622 E1 6.800 7.000 7.200 0.2677 0.2756 0.2835 E3 - 5.600 - - 0.2205 - e - 0.800 - - 0.0315 - L 0.450 0.600 0.750 0.0177 0.0236 0.0295 L1 - 1.000 - - 0.0394 - k 0 3.5 7 0 3.5 7 ccc - - 0.100 - - 0.0039 1. Values in inches are converted from mm and rounded to 4 decimal digits. Figure 50. Recommended footprint for LQFP32 package 6?&0?6 1. Dimensions are expressed in millimeters. DocID022265 Rev 6 107/121 115 Package information STM32F051x4 STM32F051x6 STM32F051x8 Device marking The following figure gives an example of topside marking orientation versus pin 1 identifier location. Figure 51. LQFP32 package marking example 3URGXFWLGHQWLILFDWLRQ 670) .7 'DWHFRGH 3LQLGHQWLILFDWLRQ < :: 5HYLVLRQFRGH 5 06Y9 1. Parts marked as "ES", "E" or accompanied by an Engineering Sample notification letter, are not yet qualified and therefore not yet ready to be used in production and any consequences deriving from such usage will not be at ST charge. In no event, ST will be liable for any customer usage of these engineering samples in production. ST Quality has to be contacted prior to any decision to use these Engineering Samples to run qualification activity. 7.7 UFQFPN32 package information UFQFPN32 is a 32-pin, 5x5 mm, 0.5 mm pitch ultra-thin fine-pitch quad flat package. 108/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Package information Figure 52. UFQFPN32 package outline ' $ H $ $ ' GGG & & 6($7,1* 3/$1( E H ( E ( ( / 3,1,GHQWLILHU ' / !"?-%?6 1. Drawing is not to scale. 2. All leads/pads should also be soldered to the PCB to improve the lead/pad solder joint life. 3. There is an exposed die pad on the underside of the UFQFPN package. This pad is used for the device ground and must be connected. It is referred to as pin 0 in Table: Pin definitions. DocID022265 Rev 6 109/121 115 Package information STM32F051x4 STM32F051x6 STM32F051x8 Table 73. UFQFPN32 package mechanical data inches(1) millimeters Symbol Min Typ Max Min Typ Max A 0.500 0.550 0.600 0.0197 0.0217 0.0236 A1 0.000 0.020 0.050 0.0000 0.0008 0.0020 A3 - 0.152 - - 0.0060 - b 0.180 0.230 0.280 0.0071 0.0091 0.0110 D 4.900 5.000 5.100 0.1929 0.1969 0.2008 D1 3.400 3.500 3.600 0.1339 0.1378 0.1417 D2 3.400 3.500 3.600 0.1339 0.1378 0.1417 E 4.900 5.000 5.100 0.1929 0.1969 0.2008 E1 3.400 3.500 3.600 0.1339 0.1378 0.1417 E2 3.400 3.500 3.600 0.1339 0.1378 0.1417 e - 0.500 - - 0.0197 - L 0.300 0.400 0.500 0.0118 0.0157 0.0197 ddd - - 0.080 - - 0.0031 1. Values in inches are converted from mm and rounded to 4 decimal digits. Figure 53. Recommended footprint for UFQFPN32 package 1. Dimensions are expressed in millimeters. 110/121 DocID022265 Rev 6 $%B)3B9 STM32F051x4 STM32F051x6 STM32F051x8 Package information Device marking The following figure gives an example of topside marking orientation versus pin 1 identifier location. Figure 54. UFQFPN32 package marking example 3URGXFWLGHQWLILFDWLRQ ). 'DWHFRGH < :: 5HYLVLRQFRGH 5 'RW SLQ 06Y9 1. Parts marked as "ES", "E" or accompanied by an Engineering Sample notification letter, are not yet qualified and therefore not yet ready to be used in production and any consequences deriving from such usage will not be at ST charge. In no event, ST will be liable for any customer usage of these engineering samples in production. ST Quality has to be contacted prior to any decision to use these Engineering Samples to run qualification activity. DocID022265 Rev 6 111/121 115 Package information 7.8 STM32F051x4 STM32F051x6 STM32F051x8 Thermal characteristics The maximum chip junction temperature (TJmax) must never exceed the values given in Table 20: General operating conditions. The maximum chip-junction temperature, TJ max, in degrees Celsius, may be calculated using the following equation: TJ max = TA max + (PD max x JA) Where: * TA max is the maximum ambient temperature in C, * JA is the package junction-to-ambient thermal resistance, in C/W, * PD max is the sum of PINT max and PI/O max (PD max = PINT max + PI/Omax), * PINT max is the product of IDD and VDD, expressed in Watts. This is the maximum chip internal power. PI/O max represents the maximum power dissipation on output pins where: PI/O max = (VOL x IOL) + ((VDDIOx - VOH) x IOH), taking into account the actual VOL / IOL and VOH / IOH of the I/Os at low and high level in the application. Table 74. Package thermal characteristics Symbol JA 7.8.1 Parameter Value Thermal resistance junction-ambient LQFP64 - 10 x 10 mm / 0.5 mm pitch 45 Thermal resistance junction-ambient LQFP48 - 7 x 7 mm 55 Thermal resistance junction-ambient LQFP32 - 7 x 7 mm 56 Thermal resistance junction-ambient UFBGA64 - 5 x 5 mm 65 Thermal resistance junction-ambient UFQFPN48 - 7 x 7 mm 32 Thermal resistance junction-ambient UFQFPN32 - 5 x 5 mm 38 Thermal resistance junction-ambient WLCSP36 - 2.6 x 2.7 mm 60 Unit C/W Reference document JESD51-2 Integrated Circuits Thermal Test Method Environment Conditions - Natural Convection (Still Air). Available from www.jedec.org 7.8.2 Selecting the product temperature range When ordering the microcontroller, the temperature range is specified in the ordering information scheme shown in Section 8: Part numbering. 112/121 DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Package information Each temperature range suffix corresponds to a specific guaranteed ambient temperature at maximum dissipation and, to a specific maximum junction temperature. As applications do not commonly use the STM32F051xx at maximum dissipation, it is useful to calculate the exact power consumption and junction temperature to determine which temperature range will be best suited to the application. The following examples show how to calculate the temperature range needed for a given application. Example 1: High-performance application Assuming the following application conditions: Maximum ambient temperature TAmax = 82 C (measured according to JESD51-2), IDDmax = 50 mA, VDD = 3.5 V, maximum 20 I/Os used at the same time in output at low level with IOL = 8 mA, VOL= 0.4 V and maximum 8 I/Os used at the same time in output at low level with IOL = 20 mA, VOL= 1.3 V PINTmax = 50 mA x 3.5 V= 175 mW PIOmax = 20 x 8 mA x 0.4 V + 8 x 20 mA x 1.3 V = 272 mW This gives: PINTmax = 175 mW and PIOmax = 272 mW: PDmax = 175 + 272 = 447 mW Using the values obtained in Table 74 TJmax is calculated as follows: - For LQFP64, 45 C/W TJmax = 82 C + (45 C/W x 447 mW) = 82 C + 20.115 C = 102.115 C This is within the range of the suffix 6 version parts (-40 < TJ < 105 C) see Table 20: General operating conditions. In this case, parts must be ordered at least with the temperature range suffix 6 (see Section 8: Part numbering). Note: With this given PDmax we can find the TAmax allowed for a given device temperature range (order code suffix 6 or 7). Suffix 6: TAmax = TJmax - (45C/W x 447 mW) = 105-20.115 = 84.885 C Suffix 7: TAmax = TJmax - (45C/W x 447 mW) = 125-20.115 = 104.885 C Example 2: High-temperature application Using the same rules, it is possible to address applications that run at high ambient temperatures with a low dissipation, as long as junction temperature TJ remains within the specified range. Assuming the following application conditions: Maximum ambient temperature TAmax = 100 C (measured according to JESD51-2), IDDmax = 20 mA, VDD = 3.5 V, maximum 20 I/Os used at the same time in output at low level with IOL = 8 mA, VOL= 0.4 V PINTmax = 20 mA x 3.5 V= 70 mW PIOmax = 20 x 8 mA x 0.4 V = 64 mW This gives: PINTmax = 70 mW and PIOmax = 64 mW: PDmax = 70 + 64 = 134 mW Thus: PDmax = 134 mW DocID022265 Rev 6 113/121 115 Package information STM32F051x4 STM32F051x6 STM32F051x8 Using the values obtained in Table 74 TJmax is calculated as follows: - For LQFP64, 45 C/W TJmax = 100 C + (45 C/W x 134 mW) = 100 C + 6.03 C = 106.03 C This is above the range of the suffix 6 version parts (-40 < TJ < 105 C). In this case, parts must be ordered at least with the temperature range suffix 7 (see Section 8: Part numbering) unless we reduce the power dissipation in order to be able to use suffix 6 parts. Refer to Figure 55 to select the required temperature range (suffix 6 or 7) according to your ambient temperature or power requirements. Figure 55. LQFP64 PD max versus TA 3' P: 6XIIL[ 6XIIL[ 7$ & 114/121 DocID022265 Rev 6 06Y9 STM32F051x4 STM32F051x6 STM32F051x8 8 Part numbering Part numbering For a list of available options (memory, package, and so on) or for further information on any aspect of this device, please contact your nearest ST sales office. Table 75. Ordering information scheme Example: STM32 F 051 R 8 T 6 x Device family STM32 = ARM-based 32-bit microcontroller Product type F = General-purpose Sub-family 051 = STM32F051xx Pin count K = 32 pins T = 36 pins C = 48 pins R = 64 pins User code memory size 4 = 16 Kbyte 6 = 32 Kbyte 8 = 64 Kbyte Package H = UFBGA T = LQFP U = UFQFPN Y = WLCSP Temperature range 6 = -40 C to +85 C 7 = -40 C to +105 C Options xxx = code ID of programmed parts (includes packing type) TR = tape and reel packing blank = tray packing DocID022265 Rev 6 115/121 115 Revision history 9 STM32F051x4 STM32F051x6 STM32F051x8 Revision history Table 76. Document revision history Date Revision 05-Apr-2012 1 Initial release 2 Updated Table: STM32F051xx family device features and peripheral counts for SPI and I2C in 32-pin package. Corrected Group 3 pin order in Table: Capacitive sensing GPIOs available on STM32F051xx devices. Updated the current consumption values in Section: Electrical characteristics. Updated Table: HSI14 oscillator characteristics 3 Features reorganized and Figure: Block diagram structure changed. Added LQFP32 package. Updated Section: Cyclic redundancy check calculation unit (CRC). Modified the number of priority levels in Section: Nested vectored interrupt controller (NVIC). Added note 3. for PB2 and PB8, changed TIM2_CH_ETR into TIM2_CH1_ETR in Table: Pin definitions and Table: Alternate functions selected through GPIOA_AFR registers for port A. Added Table: Alternate functions selected through GPIOB_AFR registers for port B. Updated IVDD, IVSS, and IINJ(PIN) in Table: Current characteristics. Updated ACCHSI in Table: HSI oscillator characteristics and Table: HSI14 oscillator characteristics. Updated Table: I/O current injection susceptibility. Added BOOT0 input low and high level voltage in Table: I/O static characteristics. Modified number of pins in VOL and VOH description, and changed condition for VOLFM+ in Table: Output voltage characteristics. Changed VDD to VDDA in Figure: Typical connection diagram using the ADC. Updated Ts_temp in Table: TS characteristics. Updated Figure: I/O AC characteristics definition. 25-Apr-2012 23-Jul-2012 116/121 Changes DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Revision history Table 76. Document revision history (continued) Date 13-Jan-2014 Revision Changes 4 Modified datasheet title. Added packages UFQFPN48 and UFBGA64. Replaced "backup domain with "RTC domain" throughout the document. Changed SRAM value from "4 to 8 Kbyte" to "8 Kbyte" Replaced IWWDG with IWDG in Figure: Block diagram. Added inputs LSI and LSE to the multiplexer in Figure: Clock tree. Added feature "Reference clock detection" in Section: Realtime clock (RTC) and backup registers. Modified junction temperature in Table: Thermal characteristics. Renamed Table: Internal voltage reference calibration values. Replaced VDD with VDDA and VRERINT with VREFINT in Table: Embedded internal reference voltage. Rephrased introduction of Section: Touch sensing controller (TSC). Rephrased Section: Voltage regulator. Added sentence "If this is used when the voltage regulator is put in low power mode..." under "Stop mode" in Section: Lowpower modes. Removed sentence "The internal voltage reference is also connected to ADC_IN17 input channel of the ADC." in Section: Comparators (COMP). Removed feature "Periodic wakeup from Stop/Standby" in Section: Real-time clock (RTC) and backup registers. Replaced IDD with IDDA in Table: HSI oscillator characteristics, Table: HSI14 oscillator characteristics and Table: LSI oscillator characteristics. Moved section "Wakeup time from low-power mode" to Section 6.3.6 and rephrased the section. Added lines D2 and E2 in Table: UFQFPN48 - 7 x 7 mm, 0.5 mm pitch, package mechanical data. Added "The peripheral clock used is 48 MHz." in Section Onchip peripheral current consumption. DocID022265 Rev 6 117/121 120 Revision history STM32F051x4 STM32F051x6 STM32F051x8 Table 76. Document revision history (continued) Date 13-Jan-2014 118/121 Revision Changes 4 (continued) Added "Negative induced leakage current is caused by negative injection and positive induced leakage current is caused by positive injection" in Section Functional susceptibility to I/O current injection. Replaced reference "JESD22-C101" with "ANSI/ESD STM5.3.1" in Table : ESD absolute maximum ratings. Merged Table: Typical and maximum VDD consumption in Stop and Standby modes and Table: Typical and maximum VDDA consumption in Stop and Standby modes into Table: Typical and maximum current consumption in Stop and Standby modes. Updated: - Table: Temperature sensor calibration values, - Table: Internal voltage reference calibration values, - Table: Current characteristics, - Table: General operating conditions, - Table: Typical and maximum current consumption from the VDDA supply, - Table: Low-power mode wakeup timings, - Table: I/O current injection susceptibility, - Table: I/O static characteristics, - Table: Output voltage characteristics, - Table: NRST pin characteristics, - Table: I2C analog filter characteristics, - Figure: Power supply scheme, - Figure: TC and TTa I/O input characteristics, - Figure: Five volt tolerant (FT and FTf) I/O input characteristics, - Figure: I/O AC characteristics definition, - Figure: ADC accuracy characteristics, - Figure: Typical connection diagram using the ADC, - Figure: LQFP64 - 10 x 10 mm 64 pin low-profile quad flat package outline, - Figure: LQFP64 recommended footprint, - Figure: LQFP48 - 7 x 7 mm, 48 pin low-profile quad flat package outline, - Figure: LQFP48 recommended footprint, - Figure: LQFP32 - 7 x 7 mm 32-pin low-profile quad flat package outline, - Figure: LQFP32 recommended footprint, - Figure: UFQFPN48 - 7 x 7 mm, 0.5 mm pitch, package outline. DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 Revision history Table 76. Document revision history (continued) Date 28-Aug-2015 Revision 5 Changes Updated the following: - DAC and power management feature descriptions in Features - Table 2: STM32F051xx family device features and peripheral count - Section 3.5.1: Power supply schemes - Figure 13: Power supply scheme - Table 17: Voltage characteristics - Table 20: General operating conditions: updated the footnote for VIN parameter - Table 28: Typical and maximum current consumption from the VBAT supply - Table 52: ADC characteristics - Table 33: High-speed external user clock characteristics: replaced VDD with VDDIOX - Table 34: Low-speed external user clock characteristics: replaced VDD with VDDIOX - Table 37: HSI oscillator characteristics and Figure 19: HSI oscillator accuracy characterization results for soldered parts - Table 38: HSI14 oscillator characteristics: changed the min value for ACCHSI14 - Table 41: Flash memory characteristics: changed the values for tME and IDD in write mode - Table 43: EMS characteristics: changed the value of VEFTB - Table 45: ESD absolute maximum ratings - Figure 10: STM32F051x8 memory map - Figure 21: TC and TTa I/O input characteristics - Figure 22: Five volt tolerant (FT and FTf) I/O input characteristics - Figure 23: I/O AC characteristics definition - tSTART definition in Table 24: Embedded internal reference voltage - tSTAB characteristics in Table 52: ADC characteristics - Table 56: Comparator characteristics: changed the description and values for VSC, VDDA and VREFINT parameters. Added Figure 28: Maximum VREFINT scaler startup time from power down - Table 57: TS characteristics: changed the min value for TStemp - Table 58: VBAT monitoring characteristics: changed the min value for TS-vbat and the typical value for R parameters - Section 6.3.22: Communication interfaces: updated the description and features in the subsection I2C interface characteristics - Table 64: I2S characteristics: updated the min values for data input hold time (master and slave receiver) DocID022265 Rev 6 119/121 120 Revision history STM32F051x4 STM32F051x6 STM32F051x8 Table 76. Document revision history (continued) Date 28-Aug-2015 16-Dec-2015 120/121 Revision Changes 5 (continued) - Table 31: Peripheral current consumption Addition of WLCSP36 package. Updates in: - Section 2: Description - Table 2: STM32F051xx family device features and peripheral count - Section 4: Pinouts and pin descriptions with the addition of Figure 7: WLCSP36 package pinout - Table 13: Pin definitions - Table 20: General operating conditions - Section 7: Package information with the addition of Section 7.5: WLCSP36 package information - Table 74: Package thermal characteristics - Section 8: Part numbering Update of the device marking examples in Section 7: Package information. 6 Section 2: Description: - Table 2: STM32F051xx family device features and peripheral count - number of SPIs corrected for 64-pin packages - Figure 1: Block diagram modified Section 3: Functional overview: - Figure 2: Clock tree modified; divider for CEC corrected - Table 8: Comparison of I2C analog and digital filters adding 20 mA information for FastPlus mode Section 4: Pinouts and pin descriptions: - Package pinout figures updated (look and feel) - Figure 7: WLCSP36 package pinout - now presented in top view - Table 13: Pin definitions - notes added (VSSA corrected to pin 16 on LQFP32); note 5 added Section 5: Memory mapping: - added information on STM32F051x4/x6 difference versus STM32F051x8 map in Figure 10 Section 6: Electrical characteristics: - Table 24: Embedded internal reference voltage - removed 40C-85C temperature range line and the associated note - Table 48: I/O static characteristics - removed note - Section 6.3.16: 12-bit ADC characteristics - changed introductory sentence - Table 52: ADC characteristics updated and table footnotes 3 and 4 added - Table 56: Comparator characteristics - VDDA min modified - Table 59: TIMx characteristics modified - Table 64: I2S characteristics reorganized - Figure 52: UFQFPN32 package outline - figure footnotes added DocID022265 Rev 6 STM32F051x4 STM32F051x6 STM32F051x8 IMPORTANT NOTICE - PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST's terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers' products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. (c) 2015 STMicroelectronics - All rights reserved DocID022265 Rev 6 121/121 121