NL27WZ07 Dual Buffer with Open Drain Outputs The NL27WZ07 is a high performance dual buffer with open drain outputs operating from a 1.65 to 5.5 V supply. The internal circuit is composed of multiple stages, including an open drain output which provides the capability to set output switching level. This allows the NL27WZ07 to be used to interface 5 V circuits to circuits of any voltage between VCC and 7 V using an external resistor and power supply. http://onsemi.com MARKING DIAGRAMS Features * * * * * 6 Extremely High Speed: tPD 2.3 ns (typical) at VCC = 5 V Designed for 1.65 V to 5.5 V VCC Operation, CMOS compatible Over Voltage Tolerant Inputs LVTTL Compatible - Interface Capability with 5 V TTL Logic with VCC = 3 V LVCMOS Compatible 24 mA Output Sink Capability Near Zero Static Supply Current Substantially Reduces System Power Requirements Chip Complexity: FET = 72; Equivalent Gate = 18 Pb-Free Packages are Available IN A1 1 6 SC-88 DF SUFFIX CASE 419B 1 M * * * * M7 M G G 1 M7 M G G TSOP-6 DT SUFFIX CASE 318G 1 1 M7 = Device Code M = Date Code* G = Pb-Free Package (Note: Microdot may be in either location) *Date Code orientation and/or position may vary depending upon manufacturing location. OUT Y1 PIN ASSIGNMENT 1 GND IN A2 2 5 3 4 VCC OUT Y2 IN A1 2 GND 3 IN A2 4 OUT Y2 5 VCC 6 OUT Y1 FUNCTION TABLE Figure 1. Pinout (Top View) A Input L H IN A1 1 OUT Y1 IN A2 1 OUT Y2 May, 2008 - Rev. 10 L Z ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. Figure 2. Logic Symbol (c) Semiconductor Components Industries, LLC, 2008 Y Output 1 Publication Order Number: NL27WZ07/D NL27WZ07 MAXIMUM RATINGS Symbol VCC Characteristics Value Unit *0.5 to )7.0 V *0.5 VI )7.0 V *0.5 VO 7.0 V VI < GND *50 mA VO < GND *50 mA DC Supply Voltage VI DC Input Voltage VO DC Output Voltage IIK DC Input Diode Current IOK DC Output Diode Current Output in Z or LOW State (Note 1) IO DC Output Sink Current $50 mA ICC DC Supply Current per Supply Pin $100 mA IGND DC Ground Current per Ground Pin $100 mA TSTG Storage Temperature Range *65 to )150 C PD Power Dissipation in Still Air SC-88, TSOP-6 200 mW qJA Thermal Resistance SC-88, TSOP-6 333 C/W TL Lead Temperature, 1 mm from case for 10 s TJ Junction Temperature under Bias ILatchup Latchup Performance MSL Moisture Sensitivity FR Flammability Rating VESD ESD Classification Above VCC and Below GND at 85C (Note 5) 260 C )150 C $500 mA Level 1 Oxygen Index: 28 to 34 UL 94 V-0 @ 0.125 in Human Body Model (Note 3) Machine Model (Note 4) Charged Device Model (Note 5) > 2000 > 200 N/A Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. IO absolute maximum rating must be observed. 2. Tested to EIA/JESD22-A114-A, rated to EIA/JESD22-A114-B. 3. Tested to EIA/JESD22-A115-A, rated to EIA/JESD22-A115-A. 4. Tested to JESD22-C101-A 5. Tested to EIA/JESD78 RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage VI Input Voltage VO Output Voltage TA Operating Free-Air Temperature Dt/DV Input Transition Rise or Fall Rate Operating Data Retention Only (Z or LOW State) VCC = 2.5 V $0.2 V VCC =3.0 V $0.3 V VCC =5.0 V $0.5 V http://onsemi.com 2 Min Max Unit 1.65 1.5 5.5 5.5 V 0 5.5 V 0 5.5 V -55 +125 C 0 0 0 20 10 5 ns/V NL27WZ07 DC ELECTRICAL CHARACTERISTICS Symbol Parameter Condition TA = 25C VCC (V) Min 0.75 VCC 0.75 VCC Typ -55C TA 125C Max Min Max High-Level Input Voltage 1.65 to 1.95 2.3 to 5.5 VIL Low-Level Input Voltage 1.65 to 1.95 2.3 to 5.5 0.3 VCC 0.3 VCC 0.3 VCC 0.3 VCC V ILKG Z-State Output Leakage Current VIN = VIL VOUT = VCC or GND 2.3 to 5.5 $5.0 $10.0 mA VOL Low-Level Output Voltage VIN = VIL IOL = 100 mA 1.65 to 5.5 0.0 0.1 0.1 V IOL = 4 mA 1.65 0.08 0.24 0.24 IIN Input Leakage Current IOFF Power Off-Output Leakage Current ICC Quiescent Supply Current 0.75 VCC 0.75 VCC Unit VIH V IOL = 8 mA 2.3 0.20 0.3 0.3 IOL = 12 mA 2.7 0.22 0.4 0.4 IOL = 16 mA 3.0 0.28 0.4 0.4 IOL = 24 mA 3.0 0.38 0.55 0.55 IOL = 32 mA 4.5 0.42 0.55 0.55 VIN or VOUT = VCC or GND 0 to 5.5 $0.1 $1.0 mA VOUT = 5.5 V 0 1 10 mA VIN = VCC or GND 5.5 1 10 mA IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIII IIIIIIIII IIII IIIIIII IIIIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIII IIIIIIIII IIIIIII IIIIIII IIIIII II III III III IIII IIII IIIIIII IIIIIIIII IIII III III III III IIII II IIII IIIIIII IIIIIIIII IIII III III III III IIII II IIIIIIIII IIIIIII III III III IIII IIIIIIIIIII II IIII IIIIIII IIIIIIIII IIII III III III III IIII II IIII IIIIIII IIIIIIIII IIII III III III III IIII II IIIIIIIII IIII III III III III IIII IIII IIIIIII II IIII IIIIIII IIIIIIIII II IIII III III III III IIII IIIIIIIIIII IIIIIIIII II IIII III III III III IIII IIIIIIIII IIIIIIIIIII II IIIIIII III III III IIII AC ELECTRICAL CHARACTERISTICS tR = tF = 2.5 ns; CL = 50 pF; RL = 500 W TA = 25C Symbol tPZL Condition VCC (V) Min Typ Max Min Max Unit RL = R1= 5000 W, CL = 15 pF 1.8 $ 0.15 1.8 5.3 11.5 1.8 12.0 ns 2.5 $ 0.2 1.2 3.7 5.8 1.2 6.4 3.3 $ 0.3 0.8 2.9 4.4 0.8 4.8 5.0 $ 0.5 0.5 2.3 3.5 0.5 3.9 1.8 $ 0.15 1.8 5.3 11.5 1.8 12.0 2.5 $ 0.2 1.2 2.8 5.8 1.2 6.4 3.3 $ 0.3 0.8 2.1 4.4 0.8 4.8 5.0 $ 0.5 0.5 1.4 3.5 0.5 3.9 Parameter Propagation Delay (Figure 3 and 4) RL = R1= 500 W, CL = 50 pF tPLZ Propagation Delay (Figure 3 and 4) -55C TA 125C RL = R1= 5000 W, CL = 15 pF RL = R1= 500 W, CL = 50 pF ns CAPACITIVE CHARACTERISTICS Symbol Condition Typical Unit Input Capacitance VCC = 5.5 V, VI = 0 V or VCC 2.5 pF COUT Output Capacitance VCC = 5.5 V, VI = 0 V or VCC 4.0 pF CPD Power Dissipation Capacitance (Note 6) 10 MHz, VCC = 5.5 V, VI = 0 V or VCC 4.0 pF CIN Parameter 6. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin ) ICC. CPD is used to determine the no-load dynamic power consumption; PD = CPD VCC2 fin ) ICC VCC. http://onsemi.com 3 NL27WZ07 A VCC 50% tPZL Y GND tPLZ HIGH IMPEDANCE 50% VCC VOL )0.3 V Figure 3. Switching Waveforms VCC R1 PULSE GENERATOR DUT RT CL VCC 2 RL RT = ZOUT of pulse generator (typically 50 W) Figure 4. Test Circuit ORDERING INFORMATION Device Package NL27WZ07DFT2 SC-88 / SOT-363 / SC-70 NL27WZ07DFT2G SC-88 / SOT-363 / SC-70 (Pb-Free) NL27WZ07DTT1 TSOP-6 / SOT-23 / SC-59 NL27WZ07DTT1G TSOP-6 / SOT-23 / SC-59 (Pb-Free) Shipping 3000 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 4 NL27WZ07 PACKAGE DIMENSIONS SC-88/SC70-6/SOT-363 CASE 419B-02 ISSUE W NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419B-01 OBSOLETE, NEW STANDARD 419B-02. D e 6 5 4 1 2 3 HE DIM A A1 A3 b C D E e L HE -E- b 6 PL 0.2 (0.008) M E M MILLIMETERS MIN NOM MAX 0.80 0.95 1.10 0.00 0.05 0.10 0.20 REF 0.10 0.21 0.30 0.10 0.14 0.25 1.80 2.00 2.20 1.15 1.25 1.35 0.65 BSC 0.10 0.20 0.30 2.00 2.10 2.20 A3 C A A1 L SOLDERING FOOTPRINT* 0.50 0.0197 0.65 0.025 0.65 0.025 0.40 0.0157 1.9 0.0748 SCALE 20:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 5 INCHES NOM MAX 0.037 0.043 0.002 0.004 0.008 REF 0.004 0.008 0.012 0.004 0.005 0.010 0.070 0.078 0.086 0.045 0.049 0.053 0.026 BSC 0.004 0.008 0.012 0.078 0.082 0.086 MIN 0.031 0.000 NL27WZ07 PACKAGE DIMENSIONS TSOP-6 CASE 318G-02 ISSUE T NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. D 6 HE 1 5 4 2 3 E b e c A 0.05 (0.002) q L A1 DIM A A1 b c D E e L HE q MIN 0.90 0.01 0.25 0.10 2.90 1.30 0.85 0.20 2.50 0 MILLIMETERS NOM MAX 1.00 1.10 0.06 0.10 0.38 0.50 0.18 0.26 3.00 3.10 1.50 1.70 0.95 1.05 0.40 0.60 2.75 3.00 10 - MIN 0.035 0.001 0.010 0.004 0.114 0.051 0.034 0.008 0.099 0 INCHES NOM 0.039 0.002 0.014 0.007 0.118 0.059 0.037 0.016 0.108 - MAX 0.043 0.004 0.020 0.010 0.122 0.067 0.041 0.024 0.118 10 SOLDERING FOOTPRINT* 2.4 0.094 1.9 0.075 0.95 0.037 0.95 0.037 0.7 0.028 1.0 0.039 SCALE 10:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 6 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NL27WZ07/D