TPS79015, TPS79018, TPS79025, TPS79028, TPS79030 ULTRALOW-POWER LOW-NOISE 50-mA LOW-DROPOUT LINEAR REGULATORS SLVS299B - SEPTEMBER 2000 - REVISED MAY 2001 D D D D D D D D D 50-mA Low-Dropout Regulator Available in 1.5-V, 1.8-V, 2.5-V, 2.8-V, 3.0-V Output Noise Typically 56 VRMS (TPS79030) Only 17 A Quiescent Current at 50 mA 1 A Quiescent Current in Standby Mode Dropout Voltage Typically 57 mV at 50 mA (TPS79030) Over Current Limitation -40C to 125C Operating Junction Temperature Range 5-Pin SOT-23 (DBV) Package DBV PACKAGE (TOP VIEW) IN 1 GND 2 EN 3 5 OUT 4 BYPASS TPS79030 GROUND CURRENT vs JUNCTION TEMPERATURE 22 VI = 4 V Co = 4.7 F 21 The usual PNP pass transistor has been replaced by a PMOS pass element. Because the PMOS pass element behaves as a low-value resistor, the dropout voltage is very low, typically 57 mV at 50 mA of load current (TPS79030), and is directly proportional to the load current. The quiescent current is ultralow (17 A typically) and is stable over the entire range of output load current (0 mA to 50 mA). Intended for use in portable systems such as laptops and cellular phones, the ultralow-dropout voltage feature and ultralowpower operation result in a significant increase in system battery operating life. 20 IO = 50 mA 19 IO = 1 mA 18 17 16 15 -40 -25 -10 5 20 35 50 65 80 95 110 125 TJ - Junction Temperature - C TPS78930 OUTPUT SPECTRAL NOISE DENSITY vs FREQUENCY 1200 Output Spectral Noise Density -V/ Hz The TPS790xx family of low-dropout (LDO) voltage regulators offers the benefits of low-dropout voltage, ultralow-power operation, low-output noise, and miniaturized packaging. These regulators feature low-dropout voltages and ultralow quiescent current compared to conventional LDO regulators. An internal resistor, in conjunction with an external bypass capacitor, creates a low-pass filter to reduce the noise. The TPS79030 exhibits only 56 VRMS of output voltage noise using 0.01 F bypass and 10 F output capacitors. Offered in a 5-terminal small outline integrated-circuit SOT-23 package, the TPS790xx series devices are ideal for micropower operations, low output noise, and where board space is limited. Ground Current - A description VI = 4 V Co = 4.7 F C(byp) = 0.1 F 1000 800 600 IO = 50 mA IO = 1 mA 400 200 0 100 1k 10k f - Frequency - Hz 100k Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2001, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 TPS79015, TPS79018, TPS79025, TPS79028, TPS79030 ULTRALOW-POWER LOW-NOISE 50-mA LOW-DROPOUT LINEAR REGULATORS SLVS299B - SEPTEMBER 2000 - REVISED MAY 2001 description (continued) The TPS790xx also features a logic-enabled sleep mode to shut down the regulator, reducing quiescent current to 1 A typical at TJ = 25C. The TPS790xx is offered in 1.5 V, 1.8 V, 2.5 V, 2.8 V, 3.0 V. AVAILABLE OPTIONS VOLTAGE TJ PACKAGE PART NUMBER TPS79015DBVT TPS79015DBVR TPS79018DBVT TPS79018DBVR TPS79025DBVT TPS79025DBVR 1.5 V 1.8 V -40C to 125C 2.5 V SOT-23 SOT 23 (DBV) TPS79028DBVT TPS79030DBVT 2.8 V 3.0 V TPS79028DBVR TPS79030DBVR The DBVT indicates tape and reel of 250 parts. The DBVR indicates tape and reel of 3000 parts. functional block diagram TPS79015/18/25/28/30 OUT IN EN 150 k Current Limit / Thermal Protection Vref GND Bypass Terminal Functions TERMINAL I/O DESCRIPTION NAME NO. BYPASS 4 I Bypass EN 3 I Enable input GND 2 IN 1 I Input supply voltage OUT 5 O Regulated output voltage 2 Ground POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SYMBOL PEBI PECI PEDI PEEI PEFI TPS79015, TPS79018, TPS79025, TPS79028, TPS79030 ULTRALOW-POWER LOW-NOISE 50-mA LOW-DROPOUT LINEAR REGULATORS SLVS299B - SEPTEMBER 2000 - REVISED MAY 2001 detail description The TPS790xx uses a PMOS pass element to dramatically reduce both dropout voltage and supply current over more conventional PNP-pass-element LDO designs. The PMOS pass element is a voltage-controlled device and, unlike a PNP transistor, it does not require increased drive current as output current increases. Supply current in the TPS790xx is essentially constant from no load to maximum load. The TPS790xx family of low-dropout (LDO) regulators have been optimized for use in battery-operated equipment. They feature extremely low dropout voltages, low output noise, low quiescent current (17 A typically), and enable inputs to reduce supply currents to 1 A when the regulators are turned off. The internal voltage reference is a key source of noise in a LDO regulator. The TPS790xx has a BYPASS pin which is connected to the voltage reference through a 150-k internal resistor. The 150-k internal resistor, in conjunction with an external bypass capacitor connected to the BYPASS pin, creates a low pass filter to reduce the voltage reference noise and, therefore, the noise at the regulator output. Note that the output will start up slower as the bypass capacitance increases due to the RC time constant at the bypass pin that is created by the internal 150-k resistor and external capacitor. Current limiting and thermal protection prevent damage by excessive output current and/or power dissipation. The device switches into a constant-current mode at approximately 350 mA; further load reduces the output voltage instead of increasing the output current. The thermal protection shuts the regulator off if the junction temperature rises above approximately 165C. Recovery is automatic when the junction temperature drops approximately 25C below the high temperature trip point. The PMOS pass element includes a back gate diode that conducts reverse current when the input voltage level drops below the output voltage level. A voltage of 1.7 V or greater on the EN input will disable the TPS790xx internal circuitry, reducing the supply current to 1 A. A voltage of less than 0.9 V on the EN input will enable the TPS790xx and will enable normal operation to resume. The EN input does not include any deliberate hysteresis, and it exhibits an actual switching threshold of approximately 1.5 V. absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Input voltage range (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.3 V to 13.5 V Voltage range at EN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to VI + 0.3 V Voltage on OUT, FB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Peak output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internally limited ESD rating, HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kV Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating virtual junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 40C to 150C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: All voltage values are with respect to network ground terminal. DISSIPATION RATING TABLE BOARD PACKAGE RJC RJA DERATING FACTOR ABOVE TA = 25C TA 25C POWER RATING TA = 70C POWER RATING TA = 85C POWER RATING Low K High K DBV 65.8 C/W 259 C/W 3.9 mW/C 386 mW 212 mW 154 mW DBV 65.8 C/W 180 C/W 5.6 mW/C 555 mW 305 mW 222 mW The JEDEC Low K (1s) board design used to derive this data was a 3 inch x 3 inch, two layer board with 2 ounce copper traces on top of the board. The JEDEC High K (2s2p) board design used to derive this data was a 3 inch x 3 inch, multilayer board with 1 ounce internal power and ground planes and 2 ounce copper traces on top and bottom of the board. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 TPS79015, TPS79018, TPS79025, TPS79028, TPS79030 ULTRALOW-POWER LOW-NOISE 50-mA LOW-DROPOUT LINEAR REGULATORS SLVS299B - SEPTEMBER 2000 - REVISED MAY 2001 recommended operating conditions MIN Input voltage, VI (see Note 2) NOM 2.7 Continuous output current, IO (see Note 3) Operating junction temperature, TJ MAX UNIT 10 V 0 50 mA -40 125 C NOTES: 2. To calculate the minimum input voltage for your maximum output current, use the following formula: VI(min) = VO(max) + VDO (max load) 3. Continuous output current and operating junction temperature are limited by internal protection circuitry, but it is not recommended that the device operate under conditions beyond those specified in this table for extended periods of time. electrical characteristics over recommended operating free-air temperature range, VI = VO(typ) + 1 V, IO = 1 mA, EN = 0V, Co = 4.7 F (unless otherwise noted) PARAMETER TEST CONDITIONS Output voltage A to 50 mA load)) g (10 ( (see Note 4) TPS79015 TJ = 25C, TJ = -40C to 125C, 2.7 V < VI < 10 V TPS79018 TJ = 25C, TJ = -40C to 125C, 2.8 V < VI < 10 V TPS79025 TJ = 25C, TJ = -40C to 125C, 3.5 V < VI < 10 V TPS79028 TJ = 25C, TJ = -40C to 125C, 3.8 V < VI < 10 V TPS79030 TJ = 25C, TJ = -40C to 125C, 2.7 V < VI < 10 V 2.8 V < VI < 10 V 3.5 V < VI < 10 V Load regulation EN = 0 V, TJ = 25C IO = 10 A to 50 mA, Output voltage line regulation (VO/VO) (see Notes 4 and 5) VO + 1 V < VI 10 V, TJ = 25C VO + 1 V < VI 10 V, TJ = -40C to 125C Output noise voltage (TPS79030) BW = 300 Hz to 50 kHz, C(byp) = 0.01 F, Co = 10 F, IO = 50 mA, TJ = 25C VO = 0 V, EN = VI , See Note 4 UNIT 1.8 1.854 2.5 2.425 2.575 V 2.8 2.910 IO = 50 mA, MAX 1.545 1.746 4.0 V < VI < 10 V EN = 0 V, TJ = -40C to 125C Output current limit 1.455 2.716 10 A < IO < 50 mA, TYP 1.5 3.8 V < VI < 10 V 4.0 V < VI < 10 V EN = 0 V, TJ = 25C Quiescent current (GND current) (see Note 4) MIN 2.884 3 3.090 17 A 28 8 mV 0.04 0.1 Vrms 56 350 %/V 750 mA 2.7 < VI < 10 V 1 A TJ = -40C to 125C 2 A NOTES: 4. The minimum IN operating voltage is 2.7 V or VO (typ) + 1 V, whichever is greater. The maximum IN voltage is 10 V. The minimum output current is 10 A and the maximum output current is 50 mA. 5. If VO 1.8 V then VImin = 2.7 V, VImax = 10 V: Standby current Line Reg. (mV) + %V V O V Imax * 2.7 V 100 If VO 2.5 V then VImin = VO + 1 V, VImax = 10 V: Line Reg. (mV) 4 + %V V O V Imax * V 100 O 1000 )1 V POST OFFICE BOX 655303 1000 * DALLAS, TEXAS 75265 TPS79015, TPS79018, TPS79025, TPS79028, TPS79030 ULTRALOW-POWER LOW-NOISE 50-mA LOW-DROPOUT LINEAR REGULATORS SLVS299B - SEPTEMBER 2000 - REVISED MAY 2001 electrical characteristics over recommended operating free-air temperature range, VI = VO(typ) + 1 V, IO = 1 mA, EN = 0V, Co = 4.7 F (unless otherwise noted) (continued) PARAMETER TEST CONDITIONS High level enable input voltage 2.7 V < VI < 10 V Low level enable input voltage 2.7 V < VI < 10 V Power supply ripple rejection (TPS79030) f = 1 kHz, TJ = 25C, Input current (EN) Dropout voltage (see Note 6) Dropout voltage (see Note 6) MIN TYP MAX UNIT 1.7 V 0.9 Co = 10 F, C(byp) = 0.01 F V 85 EN = 0 V -1 EN = VI -1 0 TPS79028 IO = 50 mA, IO = 50 mA, TJ = 25C TJ = -40C to 125C 60 TPS79030 IO = 50 mA, IO = 50 mA, TJ = 25C TJ = -40C to 125C 57 dB 1 A 1 A 125 mV 115 6. IN voltage equals VO(typ) -100 mV; The TPS79030 output voltage is set to 2.9 V. The TPS79015, TPS79018, and TPS79025 dropout voltage is limited by input voltage range limitations. TYPICAL CHARACTERISTICS Table of Graphs FIGURE VO Zo VDO VO Output voltage vs Output current 1, 2, 3 vs Junction temperature 4, 5, 6 Ground current vs Junction temperature Output spectral noise density vs Frequency Root mean squared output noise vs Bypass capacitance 11 Output impedance vs Frequency 12 Dropout voltage vs Junction temperature 13 Ripple rejection vs Frequency 14 - 16 Output voltage, enable voltage vs Time (start-up) 17 - 19 Line transient response 7 8 - 10 20, 22 Load transient response 21, 23 Equivalent series resistance (ESR) POST OFFICE BOX 655303 vs Output current * DALLAS, TEXAS 75265 24, 25 5 TPS79015, TPS79018, TPS79025, TPS79028, TPS79030 ULTRALOW-POWER LOW-NOISE 50-mA LOW-DROPOUT LINEAR REGULATORS SLVS299B - SEPTEMBER 2000 - REVISED MAY 2001 TYPICAL CHARACTERISTICS TPS79015 TPS79025 OUTPUT VOLTAGE vs OUTPUT CURRENT OUTPUT VOLTAGE vs OUTPUT CURRENT 1.515 2.545 VI = 3.5 V Co = 4.7 F TJ = 25C 1.510 VO - Output Voltage - V VO - Output Voltage - V 2.510 VI = 2.7 V Co = 4.7 F TJ = 25C 2.505 2.500 2.495 1.505 1.500 1.495 1.490 2.490 1.485 2.485 0 20 10 40 30 0 50 10 20 Figure 1 TPS79030 TPS79015 OUTPUT VOLTAGE vs OUTPUT CURRENT OUTPUT VOLTAGE vs JUNCTION TEMPERATURE 50 1.515 VI = 2.7 V Co = 4.7 F VI = 4 V Co = 4.7 F TJ = 25C 1.510 VO - Output Voltage - V 3.010 VO - Output Voltage - V 40 Figure 2 3.015 3.005 3.000 2.995 2.990 1.505 IO = 1 mA 1.500 IO = 50 mA 1.495 1.490 2.985 0 10 20 30 40 IO - Output Current - mA 50 1.485 -40 -25 -10 5 20 35 50 Figure 4 POST OFFICE BOX 655303 65 80 95 110 125 TJ - Junction Temperature - C Figure 3 6 30 IO - Output Current - mA IO - Output Current - mA * DALLAS, TEXAS 75265 TPS79015, TPS79018, TPS79025, TPS79028, TPS79030 ULTRALOW-POWER LOW-NOISE 50-mA LOW-DROPOUT LINEAR REGULATORS SLVS299B - SEPTEMBER 2000 - REVISED MAY 2001 TYPICAL CHARACTERISTICS TPS79025 TPS79030 OUTPUT VOLTAGE vs JUNCTION TEMPERATURE OUTPUT VOLTAGE vs JUNCTION TEMPERATURE 2.515 3.015 VI = 3.5 V Co = 4.7 F VI = 4 V Co = 4.7 F 3.010 IO = 1 mA 2.505 VO - Output Voltage - V VO - Output Voltage - V 2.510 2.500 IO = 50 mA 2.495 2.490 3.005 IO = 1 mA 3.000 2.995 IO = 50 mA 2.990 2.485 -40 -25 -10 5 20 35 50 65 80 2.985 -40 -25 -10 5 95 110 125 20 TPS79030 65 80 95 110 125 TPS79030 GROUND CURRENT vs JUNCTION TEMPERATURE OUTPUT SPECTRAL NOISE DENSITY vs FREQUENCY 22 1200 VI = 4 V Co = 4.7 F Output Spectral Noise Density - nV/ Hz Ground Current - A 50 Figure 6 Figure 5 21 35 TJ - Junction Temperature - C TJ - Junction Temperature - C 20 IO = 50 mA 19 IO = 1 mA 18 17 16 15 -40 -25 -10 5 20 35 50 65 80 95 110 125 VI = 4 V Co = 4.7 F C(byp) = 0.1 F 1000 800 600 IO = 50 mA IO = 1 mA 400 200 0 100 TJ - Junction Temperature - C 1k 10k 100k f - Frequency - Hz Figure 8 Figure 7 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 TPS79015, TPS79018, TPS79025, TPS79028, TPS79030 ULTRALOW-POWER LOW-NOISE 50-mA LOW-DROPOUT LINEAR REGULATORS SLVS299B - SEPTEMBER 2000 - REVISED MAY 2001 TYPICAL CHARACTERISTICS TPS79030 TPS79030 OUTPUT SPECTRAL NOISE DENSITY vs FREQUENCY OUTPUT SPECTRAL NOISE DENSITY vs FREQUENCY 1800 VI = 4 V Co = 10 F C(byp) = 0.1 F 600 Output Spectral Noise Density - nV/ Hz Output Spectral Noise Density - nV/ Hz 700 500 400 IO = 1 mA 300 IO = 50 mA 200 100 1400 C(byp) = 0.01 F 1200 C(byp) = 0.1 F 1000 800 600 400 200 0 100 1k 10k 0 100 100k 1k 10k f - Frequency - Hz f - Frequency - Hz Figure 9 OUTPUT IMPEDANCE vs FREQUENCY 300 2 Co = 10 F 1.8 250 VI = 4 V Co = 10 F TJ = 25C 1.6 Zo - Output Impedance - RMS - Root Mean Squared Output Noise - V(RMS) 100k Figure 10 ROOT MEAN SQUARED OUTPUT NOISE vs BYPASS CAPACITANCE 200 150 100 VO = 3 V 1.2 1 0.8 IO = 1 mA 0.6 0.4 50 IO = 50 mA 0.2 VO = 1.5 V 0 0.00001 1.4 0.1 0.0001 0.001 0.01 C(bypass) - Bypass Capacitance - F 1 0 10 100 1k 10k f - Frequency - Hz Figure 11 8 VI = 4 V IO = 50 mA Co = 10 F C(byp) = 0.001 F 1600 Figure 12 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 100k 1M TPS79015, TPS79018, TPS79025, TPS79028, TPS79030 ULTRALOW-POWER LOW-NOISE 50-mA LOW-DROPOUT LINEAR REGULATORS SLVS299B - SEPTEMBER 2000 - REVISED MAY 2001 TYPICAL CHARACTERISTICS TPS79030 TPS79030 DROPOUT VOLTAGE vs JUNCTION TEMPERATURE RIPPLE REJECTION vs FREQUENCY 110 75 100 IO = 50 mA IO = 1 mA 90 Ripple Rejection -dB VDO - Dropout Voltage - mV 65 VI = 2.9 V Co = 4.7 F 55 45 35 80 70 IO = 50 mA 60 50 25 40 IO = 1 mA 15 5 -40 -25 -10 VI = 4 V Co = 4.7 F C(byp) = 0.1 F 30 20 5 20 35 50 65 80 95 110 125 10 100 TA - Junction Temperature - C 1k 100k 1M 100k 1M Figure 14 Figure 13 TPS79030 TPS79030 RIPPLE REJECTION vs FREQUENCY RIPPLE REJECTION vs FREQUENCY 100 100 90 90 IO = 1 mA 80 Ripple Rejection -dB Ripple Rejection -dB 10k f - Frequency - Hz 70 IO = 50 mA 60 50 40 IO = 1 mA 80 70 IO = 50 mA 60 50 40 VI = 4 V Co = 4.7 F C(byp) = 0.01 F 30 VI = 4 V Co = 4.7 F C(byp) = 0.001 F 30 20 20 10 100 1k 10k f - Frequency - Hz 100k 1M 10 100 1k 10k f - Frequency - Hz Figure 15 Figure 16 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 TPS79015, TPS79018, TPS79025, TPS79028, TPS79030 ULTRALOW-POWER LOW-NOISE 50-mA LOW-DROPOUT LINEAR REGULATORS SLVS299B - SEPTEMBER 2000 - REVISED MAY 2001 TYPICAL CHARACTERISTICS TPS79030 Enable Voltage - V OUTPUT VOLTAGE, ENABLE VOLTAGE vs TIME (START-UP) 5 0 VO - Output Voltage - V 3 2 VI = 4 V VO = 3 V IO = 50 mA C(byp) = 0.01 F VI = 4 V Co = 4.7 F C = 4.7 F TJ = 25CO 1 0 0 1 2 3 4 5 6 t - Time - ms 7 8 9 10 TPS79030 OUTPUT VOLTAGE, ENABLE VOLTAGE vs TIME (START-UP) Enable Voltage - V TPS79030 OUTPUT VOLTAGE, ENABLE VOLTAGE vs TIME (START-UP) 5 0 3 VO - Output Voltage - V VO - Output Voltage - V Enable Voltage - V Figure 17 2 VI = 4 V VO = 3 V IO = 50 mA C(byp) = 0.001 F Co = 4.7 F TJ = 25C 1 0 0 0.2 0.4 0.6 0.8 1 1.2 t - Time - ms 1.4 1.6 1.8 2 5 0 C(byp) = 0.001 F C(byp) = 0.01 F 2 VI = 4 V VO = 3 V IO = 50 mA Co = 4.7 F TJ = 25C 1 0 0 10 Figure 18 10 C(byp) = 0.1 F 3 20 30 40 50 60 t - Time - ms Figure 19 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 70 80 90 100 TPS79015, TPS79018, TPS79025, TPS79028, TPS79030 ULTRALOW-POWER LOW-NOISE 50-mA LOW-DROPOUT LINEAR REGULATORS SLVS299B - SEPTEMBER 2000 - REVISED MAY 2001 TPS79015 LOAD TRANSIENT RESPONSE Current Load - mA TPS79015 LINE TRANSIENT RESPONSE 20 0 -20 50 0 3.7 VO - Change In Output Voltage - mV VI - Input Voltage - V VO - Output Voltage - mV TYPICAL CHARACTERISTICS 2.7 IO = 10 mA Co = 4.7 F 0 20 40 60 0 -50 VI = 2.7 V Co = 10 F -100 0 80 100 120 140 160 180 200 t - Time - s 20 40 TPS79030 LOAD TRANSIENT RESPONSE I O - Output Current - mA TPS79030 LINE TRANSIENT RESPONSE IO = 10 mA Co = 4.7 F 5 4.5 4 50 0 50 VO - Change In Output Voltage - mV VI - Input Voltage - V 80 100 120 140 160 180 200 t - Time - s Figure 21 Figure 20 VO - Output Voltage - mV 60 20 0 -20 0 20 40 60 80 100 120 140 160 180 200 t - Time - s 0 -50 VI = 4 V Co = 4.7 F -100 0 20 40 60 80 100 120 140 160 180 200 t - Time - s Figure 23 Figure 22 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 11 TPS79015, TPS79018, TPS79025, TPS79028, TPS79030 ULTRALOW-POWER LOW-NOISE 50-mA LOW-DROPOUT LINEAR REGULATORS SLVS299B - SEPTEMBER 2000 - REVISED MAY 2001 TYPICAL CHARACTERISTICS TPS79030 TYPICAL REGIONS OF STABILITY TPS79030 TYPICAL REGIONS OF STABILITY EQUIVALENT SERIES RESISTANCE (ESR) vs OUTPUT CURRENT EQUIVALENT SERIES RESISTANCE (ESR) vs OUTPUT CURRENT 100 VI = 4 V Co = 4.7 F VO = 3 V ESR - Equivalent Series Resistance - ESR - Equivalent Series Resistance - 100 Region of Instability 10 1 Region of Stability 0.1 VI = 4 V Co = 10 F VO = 3 V Region of Instability 10 Region of Stability 1 0 5 10 15 20 25 30 35 40 45 50 0 5 15 20 25 Figure 25 Figure 24 POST OFFICE BOX 655303 30 35 IO - Output Current - mA IO - Output Current - mA 12 10 * DALLAS, TEXAS 75265 40 45 50 TPS79015, TPS79018, TPS79025, TPS79028, TPS79030 ULTRALOW-POWER LOW-NOISE 50-mA LOW-DROPOUT LINEAR REGULATORS SLVS299B - SEPTEMBER 2000 - REVISED MAY 2001 APPLICATION INFORMATION The TPS790xx family of low-dropout (LDO) regulators have been optimized for use in battery-operated equipment. They feature extremely low dropout voltages, low quiescent current (17 A typically), and enable inputs to reduce supply currents to less than 1 A when the regulators are turned off. A typical application circuit is shown in Figure 26. TPS790xx 1 VI IN BYPASS 4 OUT C1 1 F 5 VO 3 EN + GND 0.01 F 4.7 F ESR = 0.2 2 Figure 26. Typical Application Circuit external capacitor requirements Although not required, a 0.047-F or larger ceramic input bypass capacitor, connected between IN and GND and located close to the TPS790xx, is recommended to improve transient response and noise rejection. A higher-value electrolytic input capacitor may be necessary if large, fast-rise-time load transients are anticipated and the device is located several inches from the power source. Like all low dropout regulators, the TPS790xx requires an output capacitor connected between OUT and GND to stabilize the internal control loop. The minimum recommended capacitance is 4.7 F. The ESR (equivalent series resistance) of the capacitor should be between 0.2 and 10 to ensure stability. Capacitor values larger than 4.7 F are acceptable, and allow the use of smaller ESR values. Capacitances less than 4.7 F are not recommended because they require careful selection of ESR to ensure stability. Solid tantalum electrolytic, aluminum electrolytic, and multilayer ceramic capacitors are all suitable, provided they meet the requirements described above. Most of the commercially available 4.7 F surface-mount solid tantalum capacitors, including devices from Sprague, Kemet, and Nichico, meet the ESR requirements stated above. Multilayer ceramic capacitors may have very small equivalent series resistances and may thus require the addition of a low value series resistor to ensure stability. CAPACITOR SELECTION PART NO. MAX ESR SIZE (H x L x W) MFR. VALUE T494B475K016AS KEMET 4.7 F 1.5 1.9 x 3.5 x 2.8 195D106x0016x2T SPRAGUE 10 F 1.5 1.3 x 7.0 x 2.7 695D106x003562T SPRAGUE 10 F 1.3 2.5 x 7.6 x 2.5 TPSC475K035R0600 AVX 4.7 F 0.6 2.6 x 6.0 x 3.2 Size is in mm. The ESR maximum resistance is in Ohms at 100 kHz and TA = 25C. Contact the manufacturer for the minimum ESR values. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 13 TPS79015, TPS79018, TPS79025, TPS79028, TPS79030 ULTRALOW-POWER LOW-NOISE 50-mA LOW-DROPOUT LINEAR REGULATORS SLVS299B - SEPTEMBER 2000 - REVISED MAY 2001 APPLICATION INFORMATION external capacitor requirements (continued) The external bypass capacitor, used in conjunction with an internal resistor to form a low-pass filter, should be a low ESR ceramic capacitor. For example, the TPS79030 exhibits only 56 VRMS of output voltage noise using a 0.01 F ceramic bypass capacitor and a10 F ceramic output capacitors. Note that the output will start up slower as the bypass capacitance increases due to the RC time constant at the bypass pin that is created by the internal 150 k resistor and external capacitor. power dissipation and junction temperature Specified regulator operation is assured to a junction temperature of 125C; the maximum junction temperature should be restricted to 125C under normal operating conditions. This restriction limits the power dissipation the regulator can handle in any given application. To ensure the junction temperature is within acceptable limits, calculate the maximum allowable dissipation, PD(max), and the actual dissipation, PD, which must be less than or equal to PD(max). The maximum-power-dissipation limit is determined using the following equation: P D(max) * TA + TJmax R qJA Where: TJmax is the maximum allowable junction temperature. RJA is the thermal resistance junction-to-ambient for the package, see the dissipation rating table. TA is the ambient temperature. The regulator dissipation is calculated using: P D + VI * VO I O Power dissipation resulting from quiescent current is negligible. Excessive power dissipation will trigger the thermal protection circuit. regulator protection The TPS790xx PMOS-pass transistor has a built-in back diode that conducts reverse current when the input voltage drops below the output voltage (e.g., during power down). Current is conducted from the output to the input and is not internally limited. If extended reverse voltage operation is anticipated, external limiting might be appropriate. The TPS790xx features internal current limiting and thermal protection. During normal operation, the TPS790xx limits output current to approximately 350 mA. When current limiting engages, the output voltage scales back linearly until the overcurrent condition ends. While current limiting is designed to prevent gross device failure, care should be taken not to exceed the power dissipation ratings of the package. If the temperature of the device exceeds approximately 165C, thermal-protection circuitry shuts it down. Once the device has cooled down to below approximately 140C, regulator operation resumes. 14 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TPS79015, TPS79018, TPS79025, TPS79028, TPS79030 ULTRALOW-POWER LOW-NOISE 50-mA LOW-DROPOUT LINEAR REGULATORS SLVS299B - SEPTEMBER 2000 - REVISED MAY 2001 MECHANICAL DATA DBV (R-PDSO-G5) PLASTIC SMALL-OUTLINE 0,50 0,30 0,95 5 0,20 M 4 1,70 1,50 1 0,15 NOM 3,00 2,60 3 Gage Plane 3,00 2,80 0,25 0-8 0,55 0,35 Seating Plane 1,45 0,95 0,05 MIN 0,10 4073253-4/F 10/00 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion. Falls within JEDEC MO-178 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 15 PACKAGE OPTION ADDENDUM www.ti.com 4-Mar-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TPS79015DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS79015DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS79018DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS79018DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS79025DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS79025DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS79025DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS79028DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS79028DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS79030DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS79030DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS79030DBVT ACTIVE SOT-23 DBV 5 250 CU NIPDAU Level-1-260C-UNLIM Green (RoHS & no Sb/Br) Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. None: Not yet available Lead (Pb-Free). Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens, including bromine (Br) or antimony (Sb) above 0.1% of total product weight. (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated