EPCOS Product Profile 2016 PTC Thermistors www.epcos.com PTC Thermistors Contents Important notes 4 Preview 5 Overcurrent protection 6 Inrush current limiters 11 Telecom 12 Switching applications 15 Motor starting 16 Limit temperature sensors 17 Heating elements 22 Sample kits 24 Cautions and warnings 25 Symbols and terms 26 Get in contact 27 (c) EPCOS AG 2016 3 Important Notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, Alu-X, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP, CSSP, CTVS, DeltaCap, DigiSiMic, DSSP, ExoCore, FilterCap, FormFit, LeaXield, MiniBlue, MiniCell, MKD, MKK, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, PQSine, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, TFAP, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. (c) EPCOS AG 2016 Preview This short form catalog presents the wide selection of EPCOS PTC thermistors. With decades of experience in the development, manufacture and marketing of electronic components, TDK is the world market leader in PTC thermistors, and one of the world's biggest producers of electronic components, modules and systems. PTC thermistors are ceramic components whose electrical resistance rapidly increases when a certain temperature is exceeded. This property makes them ideal for use in countless applications of modern electrical and electronic engineering, for example, as self-resetting fuses against current overload or for short circuit protection in motors. PTC thermistors are used in electronic lamp ballasts and switch-mode power supplies for delayed switching. Special motor-start PTC thermistors are also used in refrigerator compressors, for instance. (c) EPCOS AG 2016 Thermal protection of motors and transformers is another example of the versatility of PTC thermistors. Their potential applications include measurement and control engineering and extend to entertainment, household and automotive electronics, as well as to IT systems and telecommunications. PTC thermistors are also suitable as self-regulating heater elements in hot plates and hotglue guns, or for auxiliary heating and carburetor and fuel injection pre-heating in automobiles. The various PTC thermistors types offered by TDK are equally diverse, providing a suitable solution for virtually every application. Backed by a wealth of expertise, our specialists are also able to produce PTC thermistors precisely to all custom specifications. Turn our creativity and competence into your success. Please read Important notes on page 4 and Cautions and warnings on page 25. 5 Overcurrent Protection Applications VV Overload and short-circuit protection, e.g. for -- motors -- transformers -- switch-mode power supplies -- battery chargers -- automotive electronics Leaded disks, coated Rated current IR mA Switching current IS mA Rated resistance RR Dimensions wmax mm Ordering code hmax mm od mm lmin mm Dimensional drawing mm VR = 12 V DC/ V AC, Vmax = 20 V DC/ V AC 1500 3050 0.45 17.5 21.0 0.6 25 B59945C0160A070 950 1900 0.80 13.5 17.0 0.6 25 B59955C0160A070 700 1450 1.20 11.0 14.5 0.6 25 B59965C0160A070 550 1100 1.80 9.0 12.5 0.6 25 B59975C0160A070 300 600 4.60 6.5 10.0 0.6 25 B59985C0160A070 150 300 13.00 4.0 7.5 0.5 25 B59995C0160A070 VR = 12, 24 V DC/ V AC, Vmax = 30 V DC/ V AC 1800 3600 0.30 22.0 25.5 0.6 35 B59935C0120A070 1300 2600 0.45 17.5 21.0 0.6 25 B59945C0120A070 850 1700 0.80 13.5 17.0 0.6 25 B59955C0120A070 600 1200 1.20 11.0 14.5 0.6 25 B59965C0120A070 450 900 1.80 9.0 12.5 0.6 25 B59975C0120A070 250 500 4.60 6.5 10.0 0.6 25 B59985C0120A070 120 240 13.00 4.0 7.5 0.5 25 B59995C0120A070 25.5 0.8 35 B59910C0130A070 VR = 63 V DC/ V AC, Vmax = 80 V DC/ V AC 1000 6 1500 1.20 22.0 700 1400 1.65 22.0 25.5 0.6 35 B59930C0120A070 700 1100 2.20 17.5 21.0 0.8 25 B59930C0130A070 450 900 2.30 17.5 21.0 0.6 25 B59940C0120A070 320 640 3.70 13.5 17.0 0.6 25 B59950C0120A070 320 500 4.90 11.0 14.5 0.6 35 B59950C0130A070 250 500 5.60 11.0 14.5 0.6 25 B59960C0120A070 250 380 8.00 9.0 12.5 0.6 25 B59960C0130A070 170 350 3.70 13.5 17.0 0.6 35 B59950C0080A070 150 300 9.40 9.0 12.5 0.6 25 B59970C0120A070 150 240 20.00 6.5 10.0 0.6 25 B59970C0130A070 130 265 5.60 11.0 14.5 0.6 35 B59960C0080A070 90 190 9.40 9.0 12.5 0.6 25 B59970C0080A070 85 170 25.00 6.5 10.0 0.6 25 B59980C0120A070 85 130 62.00 4.0 7.5 0.6 25 B59980C0130A070 50 110 25.00 6.5 10.0 0.6 25 B59980C0080A070 50 100 55.00 4.0 7.5 0.5 25 B59990C0120A070 30 60 55.00 4.0 7.5 0.5 25 B59990C0080A070 Please read Important notes on page 4 and Cautions and warnings on page 25. (c) EPCOS AG 2016 Overcurrent Protection Leaded disks, coated Rated current IR mA Switching current IS mA Rated resistance RR Dimensions Ordering code wmax mm hmax mm od mm lmin mm Dimensional drawing mm VR = 110 V DC/ V AC, Vmax = 160 V DC/ V AC 525 1050 3.7 22.0 25.5 0.6 35 B59830C0160A070 400 800 6.0 17.5 21.0 0.6 35 B59840C0160A070 250 500 10.0 13.5 17.0 0.6 25 B59850C0160A070 180 360 15.0 11.0 14.5 0.6 25 B59860C0160A070 125 250 25.0 9.0 12.5 0.6 25 B59870C0160A070 70 140 70.0 6.5 10.0 0.6 25 B59880C0160A070 35 70 150.0 4.0 7.5 0.5 25 B59890C0160A070 VR = 230 V DC/ V AC, Vmax = 265 V DC/ V AC 650 980 3.5 22.0 25.5 0.8 35 B59810C0130A070 460 920 3.7 22.0 25.5 0.6 35 B59830C0120A070 450 680 5.0 17.5 21.0 0.8 35 B59830C0130A070 330 660 6.0 17.5 21.0 0.6 35 B59840C0120A070 330 500 9.0 13.5 17.0 0.6 35 B59840C0130A070 200 400 10.0 13.5 17.0 0.6 25 B59850C0120A070 200 320 13.0 11.0 14.5 0.6 25 B59850C0130A070 170 350 6.0 17.5 21.0 0.6 35 B59840C0080A070 140 280 15.0 11.0 14.5 0.6 35 B59860C0120A070 140 230 25.0 9.0 12.5 0.6 25 B59860C0130A070 110 230 10.0 13.5 17.0 0.6 25 B59850C0080A070 100 200 25.0 9.0 12.5 0.6 25 B59870C0120A070 100 150 50.0 6.5 10.0 0.6 25 B59870C0130A070 90 180 15.0 11.0 14.5 0.6 25 B59860C0080A070 80 160 35.0 9.0 12.5 0.6 25 B59872C0120A070 70 140 45.0 9.0 12.5 0.6 25 B59873C0120A070 60 130 25.0 9.0 12.5 0.6 25 B59870C0080A070 60 125 55.0 9.0 12.5 0.6 25 B59874C0120A070 55 110 65.0 9.0 12.5 0.6 25 B59875C0120A070 55 110 70.0 6.5 10.0 0.6 25 B59880C0120A070 55 90 160.0 4.0 7.5 0.6 25 B59880C0130A070 35 70 120.0 6.5 10.0 0.6 25 B59883C0120A070 30 70 70.0 6.5 10.0 0.6 35 B59880C0080A070 30 60 150.0 4.0 7.5 0.5 25 B59890C0120A070 15 40 150.0 4.0 7.5 0.5 25 B59890C0080A070 VR = 230 V DC/ V AC, Vmax = 265 V DC/ V AC, lead-free series 220 330 10 13.5 17.0 0.6 35 B59850C0120A570 170 260 15 11.0 14.5 0.6 35 B59860C0120A570 90 140 45 9.0 12.5 0.6 35 B59873C0120A570 80 120 65 9.0 12.5 0.6 35 B59875C0120A570 65 98 70 6.5 10.0 0.6 35 B59880C0120A570 50 75 120 6.5 10.0 0.6 35 B59883C0120A570 (c) EPCOS AG 2016 Please read Important notes on page 4 and Cautions and warnings on page 25. 7 Overcurrent Protection Leaded disks, coated Rated current IR mA Switching current IS mA Rated Dimensions resistance RR wmax hmax mm mm Ordering code Dimensional drawing od mm lmin mm 10.0 0.6 25 B59884C0120A070 mm VR = 380 V DC/ V AC, Vmax = 420 V DC/ V AC 21 39 600 6.5 VR = 500 V DC/ V AC, Vmax = 550 V DC/ V AC 15 30 1200 6.5 10.0 0.6 25 B59885C0120A070 12 24 1500 6.5 10.0 0.6 25 B59886C0120A070 Leaded disks, coated and uncoated Rated current IR mA Switching current IS mA Rated Dimensions resistance RR wmax hmax mm mm Ordering code thmax mm od mm lmin mm Dimensional drawing mm VR = 400 V DC/ V AC, Vmax = 440 V DC/ V AC For B59***B... 123 245 25 12.5 16.5 5.0 0.6 35 B59750B0120A070 64 127 70 8.5 12.0 7.0 0.6 25 B59770B0120A0701) 87 173 50 13.0 18.0 7.5 0.6 35 B59751C0120A070 69 137 50 13.0 18.0 7.5 0.6 25 B59752C0120A070 56 112 120 13.0 18.0 7.5 0.6 25 B59753C0120A070 50 100 150 13.0 18.0 7.5 0.6 25 B59754C0120A070 49 97 120 9.0 13.5 7.5 0.6 25 B59771C0120A070 43 86 150 9.0 13.5 7.5 0.6 25 B59772C0120A070 1) VR = 400 V DC/ V AC, Vmax = 440 V DC/ V AC 75 150 120 16.0 20.5 8.0 0.8 35 B59412C1130B070 100 200 56 16.0 20.5 8.0 0.8 35 B59451C1130B070 For B59***C... VR = 500 V DC/ V AC, Vmax = 550 V DC/ V AC 28 55 500 13.0 18.0 7.5 0.6 35 B59755C0115A070 16 32 1100 9.0 13.5 7.5 0.6 25 B59774C0115A070 13.5 7.5 0.6 25 B59773C0120A070 7.5 0.6 35 B59758C0110A070 VR = 500 V DC/ V AC, Vmax = 550 V DC/ V AC 24 48 500 9.0 VR = 1000 V DC/ V AC, Vmax = 1000 V DC/ V AC 8 1) 17 7500 13.0 18.0 Uncoated version 8 Please read Important notes on page 4 and Cautions and warnings on page 25. (c) EPCOS AG 2016 Overcurrent Protection SMD types Rated current IR1) mA Switching current IS1) mA Rated resistance RR EIA size Ordering code Dimensional drawing mm VR = 24 V DC/ V AC, Vmax = 30 V DC/ V AC EIA case size 0402 90 180 27 1210 B59606A0110A062 70 130 55 1210 B59607A0120A062 0402 B59407A0115A062 0603 B59622A0090A062 VR = 24 V DC/ V AC, Vmax = 32 V DC/ V AC 13 32 470 VR = 42 V DC/ V AC, Vmax = 60 V DC/ V AC 20 40 220 EIA case size 0603 VR = 63 V DC/ V AC, Vmax = 80 V DC/ V AC 13 25 470 0603 B59623A0090A062 50 90 125 1210 B59707A0120A062 VR = 230 V DC/ V AC, Vmax = 265 V DC/ V AC 15 40 400 1210 B59807A0090A062 12 22 1500 1210 B59907A0120B062 1210 B59907A0120A062 VR = 230 V DC/ V AC, Vmax = 400 V DC/ V AC 12 1) 22 1500 EIA case size 1210 Measured on component soldered to standardized PCB (material FR4, thickness 1.5 mm). (c) EPCOS AG 2016 Please read Important notes on page 4 and Cautions and warnings on page 25. 9 Overcurrent Protection SMD types Rated current IR mA Switching current IS mA Rated Dimensions resistance h 0.5 w 0.5 l 0.5 RR mm mm mm EIA case a 0.3 size mm Ordering code Dimensional drawing mm VR = 24 V DC/ V AC, Vmax = 30 V DC/ V AC, Tref = 80 C 205 420 3.1 3.3 8.0 10.0 2.3 4032 B59301P1080A062 165 340 4.6 3.3 6.3 8.0 1.7 3225 B59201P1080A062 90 185 13.0 3.3 6.3 8.0 1.7 3225 B59101P1080A062 VR = 24 V DC/ V AC, Vmax = 30 V DC/ V AC, Tref = 120 C 310 640 3.1 3.3 8.0 10.0 2.3 4032 B59301P1120A062 265 545 4.6 3.3 6.3 8.0 1.7 3225 B59201P1120A062 170 355 13.0 3.3 6.3 8.0 1.7 3225 B59101P1120A062 10.0 2.3 4032 B59315P1080A062 VR = 63 V DC/ V AC, Vmax = 80 V DC/ V AC, Tref = 80 C 80 165 16.0 3.3 8.0 65 135 25.0 3.3 6.3 8.0 1.7 3225 B59215P1080A062 40 85 55.0 3.3 6.3 8.0 1.7 3225 B59115P1080A062 VR = 63 V DC/ V AC, Vmax = 80 V DC/ V AC, Tref = 120 C 150 310 16.0 3.3 8.0 10.0 2.3 4032 B59315P1120A062 100 210 25.0 3.3 6.3 8.0 1.7 3225 B59215P1120A062 70 145 55.0 3.3 6.3 8.0 1.7 3225 B59115P1120A062 10 Please read Important notes on page 4 and Cautions and warnings on page 25. (c) EPCOS AG 2016 Inrush Current Limiters Applications VV Inrush current limiter for smoothing and DC link capacitors VV To replace high-power fixed resistors for capacitor charging Inrush current limiters, leaded disks, coated Maximum voltage Vmax V AC Maximum link voltage Vlink, max V DC Rated resistance RR Reference temperature Tref (typ.) C Heat Dimensions Ordering code capacity Cth wmax hmax thmax od lmin J/K mm mm mm mm mm Dimensional drawing mm Leaded disks, operating cycles at Vmax (charging of capacitor) Nc > 100000 cycles 260 370 70 120 0.4 9.0 13.5 7.5 0.6 25 B59770C0120A070 260 370 120 120 0.6 9.0 13.5 7.5 0.6 25 B59771C0120A070 260 370 150 120 0.6 9.0 13.5 7.5 0.6 25 B59772C0120A070 280 400 25 120 1.0 13.0 18.0 5.5 0.6 35 B59750C0120A070 280 400 50 120 1.4 13.0 18.0 7.5 0.6 35 B59751C0120A070 280 400 80 120 1.4 13.0 18.0 7.5 0.6 25 B59752C0120A070 440 620 56 120 2.1 16.0 20.5 8.0 0.8 35 B59451C1130B070 440 620 120 120 1.4 13.0 18.0 7.5 0.6 25 B59753C0120A070 440 620 150 120 1.4 13.0 18.0 7.5 0.6 25 B59754C0120A070 440 620 500 120 0.6 9.0 13.5 7.5 0.6 25 B59773C0120A070 440 620 1100 115 0.6 9.0 13.5 7.5 0.6 25 B59774C0115A070 480 680 120 130 2.1 16.0 20.5 8.0 0.8 35 B59412C1130B070 560 800 500 115 1.4 13.0 18.0 7.5 0.6 35 B59755C0115A070 Inrush current limiters in housing Maximum voltage Vmax V AC Maximum link voltage Vlink, max V DC Rated resistance RR Reference temperature Tref (typ.) C Heat capacity Cth J/K Ordering code Dimensional drawing mm Phenolic resin plastic case, operating cycles at Vmax (charging of capacitor) Nc > 100000 cycles 280 400 22 130 2.3 B59105J0130A020 440 620 56 130 2.3 B59107J0130A020 560 800 100 130 2.3 B59109J0130A020 PBT plastic case, preferred types for new designs, operating cycles at Vmax (charging of capacitor) Nc > 100000 cycles 280 400 33 130 1.1 B59213J0130A020 280 400 22 130 2.3 B59215J0130A020 440 620 56 130 2.3 B59217J0130A020 560 800 100 130 2.3 B59219J0130A020 (c) EPCOS AG 2016 Please read Important notes on page 4 and Cautions and warnings on page 25. 11 Telecom Applications VV Overcurrent protection for telecom applications VV Suitable for line card applications e.g. POTS, access networks, customer premises equipment (CPE) or integrated voice data (IVD) Leaded disks Rated R25,match resistance (per packing RR unit) |R1 - R2| max Rated current IR @ 25C mA Switching Dimensions current IS @ 25C wmax hmax thmax mA mm mm mm Figure Ordering code Dimensional drawing mm VF,max = 245 V AC Figure 1 6.0 No 185 440 13.0 17.0 5.0 1 B59098C1100B051 20.8 1.0 80 240 7.5 4.0 10.5 2 B59084C1080B140 50.0 1.0 65 150 6.0 10.0 4.5 1 B59154C1130A151 50.0 1.0 65 150 6.0 10.0 4.0 2 B59154U1135B140 50.0 3.0 95 250 8.0 11.0 5.5 1 B59172C1130A151 50.0 1.0 90 190 9.0 12.5 4.5 1 B59184C1120B153 50.0 1.0 100 210 9.0 13.0 4.5 1 B59184C1130A151 55.0 3.0 90 210 8.0 11.0 5.5 1 B59173C1130A151 55.0 3.0 115 270 9.5 13.0 6.0 2 B59183C1160A140 Figure 2 12 Please read Important notes on page 4 and Cautions and warnings on page 25. (c) EPCOS AG 2016 Telecom Telecom pair protector (TPP) Rated resistance RR Rated current IR @ 25C mA Switching Resistance Ordering code current matching IS @ 25C in one housing |R2 - R1| mA Dimensional drawing mm VF,max = 245 V AC 35 100 210 < 1.0 B59535T1120A262 50 80 170 < 1.0 B59550T1120A262 9 180 360 < 1.0 B59509T1120A062 35 110 230 < 1.0 B59535T1120A062 50 90 190 < 1.0 B59550T1120A062 35 110 230 < 1.0 B59635T1120A062 50 90 190 < 1.0 B59650T1120A062 35 110 230 < 1.0 B59735T1120A062 35 130 270 < 1.0 B59735T1150A062 50 90 190 < 1.0 B59750T1120A062 (c) EPCOS AG 2016 Please read Important notes on page 4 and Cautions and warnings on page 25. 13 Telecom Telecom pair protector (TPP) Rated resistance RR Rated current IR @ 25C mA Switching Resistance Ordering code current matching IS @ 25C in one housing |R2 - R1| mA Dimensional drawing mm VF,max = 245 V AC 35 115 240 < 1.0 B59835T1120A062 Telecom pair protector (TPP), for GR1089 Central Office Rated resistance RR Rated current IR @ 25C mA Switching Resistance Ordering code current matching IS @ 25C in one housing |R2 - R1| mA Dimensional drawing mm VF,max = 600 V AC 70 70 150 < 2.0 B59970T1100A062 70 70 150 < 1.0 B59970T1100A162 14 Please read Important notes on page 4 and Cautions and warnings on page 25. (c) EPCOS AG 2016 Switching Applications Applications VV For delayed switching, primarily in switch-mode power supplies PTC thermistors in plastic case Rated resistance RR Rated current IR mA Switching current IS mA Ordering code Dimensional drawing mm Vmax = 265 V, VR = 230 V, switching cycles N = 100000 cycles 500 20 2000 5000 (c) EPCOS AG 2016 40 B59339A1501P020 10 20 B59339A1202P020 7 15 B59339A1502P020 Please read Important notes on page 4 and Cautions and warnings on page 25. 15 Motor Starting Applications VV Motor start in compressors and air conditioning systems (refrigerators) VV Time delay in turning off the auxiliary winding of single-phase AC motors (e.g. refrigerator compressors) Standard sizes Operating current Imax A Maximum voltage Vmax V Reference temperature Tref (typ.) C Breakdown RR RR Dimensions voltage (VPTC 2.5 V) VBD1) w th V mm mm Ordering code Dimensional drawing 120 > 360 4.7 20% 17.5 0.5 2.5 0.2 B59506A0120A020 mm VR = 120 VRMS 12 180 VR = 230 VRMS 6 355 135 > 700 33 20% 19.5 0.5 2.5 0.2 B59501A0135A020 7 300 135 > 600 22 20% 19.5 0.5 2.5 0.2 B59524A0135A020 8 320 120 > 650 20 20% 17.5 0.5 2.5 0.2 B59544A0120A020 8 350 120 > 700 15 30% 19.5 +0.5 3.2 0.2 B59196A0120A020 9 350 120 > 700 33 30% 19.5 +0.5 3.2 0.2 B59197A0120B020 9 400 120 > 800 38 30% 20.0 +0.2/ 5.0 0.25 B59314A0120B010 -0.8 Reference temperature Tref (typ.) C Breakdown voltage VBD1) V For B59314A* Low power consumption Maximum voltage Vmax V Operating current Imax A RR RR (VPTC 2.5 V) Ordering code Dimensional drawing mm VR = 120 VRMS 12 180 135 > 360 4.70 20% B59546A0135A020 12 200 135 > 400 6.80 20% B59548A0135A020 5 400 135 > 710 47.00 20% B59551A0135A020 8 350 135 > 640 22.00 20% B59549A0135A020 8 355 135 > 700 33.00 20% B59550A0135A020 8 350 135 > 600 15.00 20% B59556A0135A020 VR = 230 VRMS 1) PTC clamped between crown contacts (diameter: 2 mm). 16 Please read Important notes on page 4 and Cautions and warnings on page 25. (c) EPCOS AG 2016 Limit Temperature Sensors Applications Sensors for limit temperature monitoring VV in lighting applications VV in home appliances (dish washers, washing machines, ironing machines, electric cookers etc.) VV in automotive electronics VV in data and communications engineering (DC/DC converters) VV in motor windings Motor protection, single sensors Sensing temperature Tsense C Resistance R (Tsense - T) (VPTC 2.5 V) Resistance R (Tsense + T) (VPTC 2.5 V) Ordering code Dimensional drawing mm Vmax = 30 V DC, insulating test voltage Vins = 2.5 kV AC, T = 5 K 60 570 570 B59100M1060A070 70 570 570 B59100M1070A070 80 570 570 B59100M1080A070 90 550 1330 B59100M1090A070 100 550 1330 B59100M1100A070 110 550 1330 B59100M1110A070 120 550 1330 B59100M1120A070 130 550 1330 B59100M1130A070 140 550 1330 B59100M1140A070 145 550 1330 B59100M1145A070 150 550 1330 B59100M1150A070 155 550 1330 B59100M1155A070 160 550 1330 B59100M1160A070 Vmax = 30 V DC, insulating test voltage Vins = 2.5 kV AC, T = 7 K 170 570 570 B59100M1170A070 180 570 570 B59100M1180A070 Motor protection, triple sensors Vmax = 30 V DC, insulating test voltage Vins = 2.5 kV AC, T = 5 K 100 1650 3990 B59300M1100A070 110 1650 3990 B59300M1110A070 120 1650 3990 B59300M1120A070 130 1650 3990 B59300M1130A070 140 1650 3990 B59300M1140A070 150 1650 3990 B59300M1150A070 155 1650 3990 B59300M1155A070 160 1650 3990 B59300M1160A070 Vmax = 30 V DC, insulating test voltage Vins = 2.5 kV AC, T = 7 K 180 (c) EPCOS AG 2016 1710 1710 B59300M1180A070 Please read Important notes on page 4 and Cautions and warnings on page 25. 17 Limit Temperature Sensors Limit temperature sensors, leaded disks, coated, miniaturized Sensing temperature Tsense C Resistance R (Tsense - T) (VPTC 2.5 V) Resistance R (Tsense + T) (VPTC 2.5 V) Ordering code Dimensional drawing mm Vmax = 30 V DC, T = 5 K 70 570 570 B59008C0070A040 80 570 570 B59008C0080A040 90 550 1330 B59008C0090A040 100 550 1330 B59008C0100A040 110 550 1330 B59008C0110A040 120 550 1330 B59008C0120A040 130 550 1330 B59008C0130A040 140 550 1330 B59008C0140A040 150 550 1330 B59008C0150A040 160 550 1330 B59008C0160A040 Limit temperature sensors, leaded disks, coated Sensing temperature Tsense C Resistance R (Tsense - T) (VPTC 2.5 V) Resistance R (Tsense + T) (VPTC 2.5 V) Ordering code Dimensional drawing mm Vmax = 30 V DC, T = 5 K 80 570 570 B59100C0080A070 90 550 1330 B59100C0090A070 100 550 1330 B59100C0100A070 110 550 1330 B59100C0110A070 120 550 1330 B59100C0120A070 130 550 1330 B59100C0130A070 140 550 1330 B59100C0140A070 18 Please read Important notes on page 4 and Cautions and warnings on page 25. (c) EPCOS AG 2016 Limit Temperature Sensors Limit temperature sensors, probe assemblies Sensing temperature Tsense C Resistance R (Tsense - 5 K) (VPTC 2.5 V) Resistance R (Tsense + 5 K) (VPTC 2.5 V) Ordering code mm Type D1052, Vmax = 30 V DC Type D1052 60 570 570 B59052D1060A040 70 570 570 B59052D1070A040 80 570 570 B59052D1080A040 90 550 1330 B59052D1090A040 Type D901, Vmax = 30 V DC 60 570 Dimensional drawing Type D901 570 B59901D0060A040 70 570 570 B59901D0070A040 80 570 570 B59901D0080A040 90 550 1330 B59901D0090A040 100 550 1330 B59901D0100A040 110 550 1330 B59901D0110A040 120 550 1330 B59901D0120A040 Sensing temperature Tsense C Resistance R (Tsense - 10 K) (VPTC 2.5 V) Resistance R (Tsense) (VPTC 2.5 V) Ordering code Dimensional drawing mm Type D1051, Vmax = 30 V DC 100 1500 2200 B59051D1100A040 110 1500 2200 B59051D1110A040 120 1500 2200 B59051D1120A040 (c) EPCOS AG 2016 Please read Important notes on page 4 and Cautions and warnings on page 25. 19 Limit Temperature Sensors Limit temperature sensors, superior series Rated resistance RR (V Vmax) Resistance tolerance RR Sensing temperature Tsense,1 (@ 4.7 k) C % Sensing temperature Tsense,2 (@ 4.7 k) C Ordering code mm Vmax = 32 V DC, EIA case size 0402 EIA case size 0402 470 50 75 5 - B59421A0075A062 470 50 85 5 - B59421A0085A062 470 50 95 5 - B59421A0095A062 470 50 105 5 - B59421A0105A062 470 50 115 5 - B59421A0115A062 470 50 125 5 - B59421A0125A062 470 50 135 5 - B59421A0135A062 Vmax = 32 V DC, EIA case size 0603 EIA case size 0603 470 50 75 5 90 7 B59641A0075A062 470 50 85 5 100 7 B59641A0085A062 470 50 95 5 110 7 B59641A0095A062 470 50 105 5 120 7 B59641A0105A062 470 50 115 5 130 7 B59641A0115A062 470 50 125 5 140 7 B59641A0125A062 470 50 135 5 150 7 B59641A0135A062 470 50 145 5 - B59641A0145A062 Rated resistance RR (V Vmax) Resistance tolerance RR % Sensing Resistance Resistance Ordering code temperature R (Tsense,1 - 5 C) R (Tsense,1 + 5 C) Tsense,1 C k k Vmax = 32 V DC, EIA case size 0805 Dimensional drawing mm EIA case size 0805 680 50 70 5.7 5.7 B59721A0070A062 680 50 80 5.7 5.7 B59721A0080A062 680 50 90 5.5 13.3 B59721A0090A062 680 50 100 5.5 13.3 B59721A0100A062 680 50 110 5.5 13.3 B59721A0110A062 680 50 120 5.5 13.3 B59721A0120A062 680 50 130 5.5 13.3 B59721A0130A062 20 Dimensional drawing Please read Important notes on page 4 and Cautions and warnings on page 25. (c) EPCOS AG 2016 Limit Temperature Sensors Limit temperature sensors, standard series Rated resistance RR (V Vmax) Resistance tolerance RR % Sensing temperature Tsense,1 (@ 4.7 k) C Sensing Ordering code temperature Tsense,1 (@ 4.7 M) C Vmax = 32 V DC, EIA case size 0402, high ohmic types 10000 50 - Dimensional drawing mm EIA case size 0402 130 5 B59404A0130A062 Vmax = 32 V DC, EIA case size 0603, standard types EIA case size 0603 470 50 75 5 - B59601A0075A062 470 50 85 5 - B59601A0085A062 470 50 95 5 - B59601A0095A062 470 50 105 5 - B59601A0105A062 470 50 115 5 - B59601A0115A062 470 50 125 5 - B59601A0125A062 470 50 135 5 - B59601A0135A062 Vmax = 32 V DC, EIA case size 0603, tight temperature tolerance types 470 470 470 470 470 Rated resistance RR (V Vmax) 50 50 50 50 50 Resistance tolerance RR % 85 3 95 3 105 3 115 3 125 3 - - - - - B59601A0085B062 B59601A0095B062 B59601A0105B062 B59601A0115B062 B59601A0125B062 Sensing Resistance R Resistance R Ordering code temperature (Tsense,1 - 5 C) (Tsense,1 + 5 C) Tsense,1 C k k Vmax = 32 V DC, EIA case size 0603, tight resistance tolerance types 15 70 1.1 1.0 B59602A0055B062 470 15 55 4.7 4.7 B59603A0055A062 470 15 105 4.7 4.7 B59603A0105A062 Vmax = 32 V DC, EIA case size 0805, standard types 50 680 680 EIA case size 0805 70 5.7 5.7 B59701A0070A062 50 90 5.5 13.3 B59701A0090A062 50 100 5.5 13.3 B59701A0100A062 680 50 110 5.5 13.3 B59701A0110A062 680 50 120 5.5 13.3 B59701A0120A062 680 50 130 5.5 13.3 B59701A0130A062 680 50 140 5.5 13.3 B59701A0140A062 (c) EPCOS AG 2016 mm EIA case size 0603 110 680 Dimensional drawing Please read Important notes on page 4 and Cautions and warnings on page 25. 21 Heating Elements Applications For all sorts of heating systems VV In household appliances (hot plates, water heaters, hot-adhesive pistols, hair curlers etc.) VV In automotive electronics (preheating of diesel filter and injection system, additional heating of passenger compartment) VV In medical appliances (vaporizers, inhalators) Disk shaped with silver metallization Reference temperature Tref (typ.) C Minimum resistance Rmin (V = VR) Surface temperature Tsurf1) (V = VR) C Rated resistance RR (Vmeas 1.5 V) Ordering code Dimensional drawing mm Vmax = 30 V DC, VR = 12 V DC 0 202) 40 320 B59060A0000A010 40 42) 70 9 B59060A0040A010 60 5 80 9 B59060A0060A010 80 4 95 9 B59060A0080A010 120 4 140 9 B59060A0120A010 160 3 165 9 B59060A0160A010 180 3 185 9 B59060A0180A010 220 2 220 9 B59060A0220A010 Vmax = 265 V DC, VR = 230 V DC 1) 2) 110 960 135 4200 B59053A0110A010 130 840 155 4200 B59053A0130A010 150 700 170 4200 B59053A0150A010 180 530 200 4200 B59053A0180A010 220 640 235 6000 B59053A0220A010 Measured between points. T (RPTC = Rmin) < 25 C 22 Please read Important notes on page 4 and Cautions and warnings on page 25. (c) EPCOS AG 2016 Heating Elements Rectangular with silver metallization Reference temperature Tref (typ.) C Minimum resistance Rmin (V = VR) Surface temperature Tsurf1) (V = VR) C Rated resistance RR (Vmeas 1.5 V) Ordering code Dimensional drawing mm Vmax = 24 V DC, VR = 12 V DC 80 1.00 110 3.2 B59041R0080A010 120 1.00 145 3.2 B59041R0120A010 160 0.75 180 3.2 B59041R0160A010 180 0.75 200 3.2 B59041R0180A010 220 1.00 230 6.4 B59041R0220A010 Rectangular with aluminum metallization Reference temperature Tref (typ.) C Minimum resistance Rmin (V = VR) Surface temperature Tsurf1) (V = VR) C Rated resistance RR (Vmeas 1.5 V) Ordering code Dimensional drawing mm Vmax = 265 V DC, VR = 230 V DC 50 2252) 100 700 B59102R0050A010 70 130 115 700 B59102R0070A010 90 115 130 700 B59102R0090A010 110 100 145 700 B59102R0110A010 130 105 160 700 B59102R0130A010 150 90 180 700 B59102R0150A010 180 66 205 700 B59102R0180A010 220 80 240 1000 B59102R0220A010 240 75 255 1000 B59102R0240A010 270 85 280 1300 B59102R0270A010 Rectangular, 400 V, with aluminum metallization Reference temperature Tref (typ.) (Vmeas 1.5 V) C Minimum resistance Rmin (V = VR) Surface temperature Tsurf1) (V = VR) C Rated resistance RR (Vmeas 1.5 V) Ordering code 190 3000 B59249R0155B010 Dimensional drawing mm Vmax = 600 V DC, VR = 400 V DC 155 1) 2) 220 Measured between points T (RPTC = Rmin) < 25 C (c) EPCOS AG 2016 Please read Important notes on page 4 and Cautions and warnings on page 25. 23 Sample Kits Sample kit SMD PTC thermistors for overcurrent protection Features zz 19 different ceramic SMD PTC thermistors for overcurrent protection zz Case sizes 0402, 0603, 1210, 3225 and 4032 Ordering code: B59002Z0999A099 4100140003_ICL_Musterset_151005 05.10.15 12:22 Seite 1 Sample kit PTC inrush current limiters Features Sample Kit 2016 Inrush Current Limiters Self-Protecting PTC Resistors zz 11 different PTC inrush current limiters as self-protecting PTC resistors zz In housing or as leaded disks with coating www.epcos.com Ordering code: B59006Z0999A099 Sample kit SMD PTC thermistors for limit temperature sensing, superior series Features zz 22 different ceramic SMD PTC thermistors for limit temperature sensing zz Case sizes 0402, 0603, and 0805 zz All products from the superior series are qualified based on AEC-Q200, Rev. D Ordering code: B59001Z0999A099 Sample kit PTC thermistors as heating elements for 12 V applications Features PTC_Musterset_12V_Automotive_120228 29.02.12 15:17 Seite 1 EPCOS Sample Kit 2012 PTC Thermistors Heating Elements for 12 V Applications zz 12 different PTC heating elements zz Disk shaped with o12 mm (A60) zz Metallized rectangular, 35 x 6.2 mm (R41) www.epcos.com Ordering code: B59004Z0999A099 Sample kit PTC thermistors as heating elements for 230 V applications Features PTC_Musterset_230V_Consumer_120229 29.02.12 15:13 Seite 1 EPCOS Sample Kit 2012 PTC Thermistors Heating Elements for 230 V Applications zz 12 different PTC heating elements zz Disk shaped with o8 mm (A53) zz Metallized rectangular, 35 x 6.2 mm (R102) www.epcos.com Ordering code: B59005Z0999A099 24 Please read Important notes on page 4 and Cautions and warnings on page 25. (c) EPCOS AG 2016 Cautions and Warnings General VV Contacts and housing used for assembly with thermistor VV EPCOS thermistors are designed for specific have to be clean before mounting. Especially grease or oil must be removed. VV When PTC thermistors are encapsulated with sealing material, the precautions given in chapter "Mounting instructions", "Sealing and potting" must be observed. VV When the thermistor is mounted, there must not be any foreign body between the electrode of the thermistor and the clamping contact. VV The minimum force and pressure of the clamping contacts pressing against the PTC must be 10 N and 50 kPa, respectively. In case the assembly is exposed to mechanical shock and/ or vibration this force should be higher in order to avoid movement of the PTC during operation. VV During operation, the thermistor's surface temperature can be very high. Ensure that adjacent components are placed at a sufficient distance from the thermistor to allow for proper cooling at the thermistors. VV Ensure that adjacent materials are designed for operation at temperatures comparable to the surface temperature of thermistor. Be sure that surrounding parts and materials can withstand this temperature. VV Avoid contamination of thermistor surface during processing. applications and should not be used for purposes not identified in our specifications, application notes and data books unless otherwise agreed with EPCOS during the design-in-phase. VV Ensure suitability of thermistor through reliability testing during the design-in phase. The thermistors should be evaluated taking into consideration worst-case conditions. Storage VV Store thermistors only in original packaging. Do not open the package prior to processing. VV Storage conditions in original packaging: storage temperature -25 C ... +45 C, relative humidity 75% annual mean, maximum 95%, dew precipitation is inadmissible. VV Avoid contamination of thermistors surface during storage, handling and processing. VV Avoid storage of thermistor in harmful environment with effect on function on long-term operation (examples given under operation precautions). VV Use thermistor within the following period after delivery: -- Through-hole devices (housed and leaded PTCs): 24 months -- Motor protection sensors, glass-encapsulated sensors and probe assemblies: 24 months -- Telecom pair and quattro protectors (TPP, TQP): 24 months -- Leadless PTC thermistors for pressure contacting: 12 months -- Leadless PTC thermistors for soldering: 6 months -- SMDs in EIA sizes 3225 and 4032, and for PTCs with metal tags: 24 months -- SMDs in EIA sizes 1210 and smaller: 12 months Handling VV PTCs must not be dropped. Chip-offs must not be caused during handling of PTCs. VV The ceramic and metallization of the components must not be touched with bare hands. Gloves are recommended. VV Avoid contamination of thermistor surface during handling. Soldering (where applicable) VV Use rosin-type flux or non-activated flux. VV Insufficient preheating may cause ceramic cracks. VV Rapid cooling by dipping in solvent is not recommended. VV Complete removal of flux is recommended. VV Standard PTC heaters are not suitable for soldering. Mounting Operation VV Use thermistors only within the specified temperature operating range. VV Use thermistors only within the specified voltage and current ranges. VV Environmental conditions must not harm the thermistors. Use thermistors only in normal atmospheric conditions. Avoid use in deoxidizing gases (chlorine gas, hydrogen sulfide gas, ammonia gas, sulfuric acid gas etc), corrosive agents, humid or salty conditions. Contact with any liquids and solvents should be prevented. VV Be sure to provide an appropriate fail-safe function to prevent secondary product damage caused by abnormal function (e.g. use VDR for limitation of overvoltage condition). This listing does not claim to be complete, but merely reflects the experience of EPCOS AG. Display of ordering codes for EPCOS products The ordering code for one and the same EPCOS product can be represented differently in data sheets, data books, other publications, on the EPCOS website, or in orderrelated documents such as shipping notes, order confirmations and product labels. The varying representations of the ordering codes are due to different processes employed and do not affect the specifications of the respective products. Detailed information can be found on the Internet under www.epcos.com/orderingcodes VV Electrode must not be scratched before/during/after the mounting process. (c) EPCOS AG 2016 25 Symbols and Terms Symbol Term Cth Heat capacity Imax Operating current IR Rated current (T = TR) IS Switching current Nc Operating cycles at Vmax, charging of capacitor R25, match Resistance matching per reel/packing unit at 25 C Rmin Minimum resistance RPTC PTC resistance (at specified temperature) RR Rated resistance (T = TR) Tref Reference temperature Tsense Nominal threshold temperature Tsurf Surface temperature VBD Breakdown voltage VF, max Maximum voltage applied at fault conditions in protection mode Vins Insulation test voltage Vlink, max Maximum link voltage Vmax Maximum operating voltage Vmeas Measuring voltage VPTC Voltage drop across a PTC thermistor VR Rated voltage VRMS Root-mean-square value of voltage Tolerance e Lead spacing (in mm) Abbreviations/General notes Surface-mount devices All dimensions are given in mm. 26 (c) EPCOS AG 2016 Get in Contact Europe Austria TDK Austria GesmbH T +43 1 25 63 630 56 39 F +43 1 25 63 630 56 44 sales.austria@eu.tdk.com Bulgaria, Greece, Macedonia TDK Austria GesmbH T +43 1 25 63 630 56 30 F +43 1 25 63 630 56 44 sales.csee@eu.tdk.com Czech Republic TDK Czech s.r.o. T +420 2 33 03 22 81 F +420 2 33 03 22 89 sales.czech@eu.tdk.com Finland, Estonia TDK Nordic OY T +358 9 54 80 70 00 F +358 9 54 80 70 01 sales.nordic@eu.tdk.com France, Belgium, Luxembourg, Malta TDK Electronics France SAS T +33 1 49 46 67 89 F +33 1 49 46 67 67 sales.france@eu.tdk.com Germany, Liechtenstein, Netherlands, Switzerland TDK Europe GmbH T (D) 0180 500 33 48 (0.14 Euro/min.) (NL) +31 70 33 10 611 (CH) +49 89 54020 2691 F +49 89 54020 2913 sales.germany@eu.tdk.com Hungary TDK Electronics Hungary Ltd. T +36 1 436 07 20 F +36 1 436 07 21 sales.hungary@eu.tdk.com Russia, Belarus, Kazakhstan, Moldavia, Ukraine TDK CIS LLC T +7 495 663 21 00 +7 495 663 21 22 sales.cis@eu.tdk.com Slovakia TDK Austria GesmbH T +43 1 25 63 630 56 30 F +43 1 25 63 630 56 44 sales.slovakia@eu.tdk.com Bosnia and Herzegovina, Croatia, Montenegro, Serbia, Slovenia TDK Austria GesmbH T +43 1 25 63 630 56 30 F +43 1 25 63 630 56 44 sales.slovenia@eu.tdk.com Spain TDK Electronics Spain S.L.U. T +34 91 514 71 61 F +34 91 514 70 14 sales.iberia@eu.tdk.com Sweden, Iceland, Denmark, Norway TDK Nordic AB T +46 8 4 77 27 00 F +46 8 4 77 27 01 sales.nordic@eu.tdk.com Turkey TDK Europe GmbH T +90 216 5 69 81 01 F +90 216 4 64 07 56 sales.turkey@eu.tdk.com United Kingdom, Ireland TDK UK Limited T +44 13 44 38 15 10 F +44 13 44 38 15 12 sales.uk@eu.tdk.com Asia Italy TDK Italy S.r.l T +39 02 50 99 54 25 F +39 02 50 99 54 55 sales.italy@eu.tdk.com Afghanistan, Iran, Iraq, Jordan, Lebanon, Pakistan, Syria TDK Europe GmbH T +90 216 5 69 81 01 F +90 216 4 64 07 56 sales.turkey@eu.tdk.com Poland, Latvia, Lithuania TDK Polska Sp. z o.o. T +48 22 24 60 409 F +48 22 24 60 400 sales.poland@eu.tdk.com China EPCOS (Shanghai) Ltd. T +86 21 22 19 15 00 F +86 21 22 19 15 99 sales.cn@epcos.com Portugal TDK Electronics Spain S.L.U. T +34 93 480 42 94 F +34 93 480 42 31 sales.iberia@eu.tdk.com Hong Kong EPCOS Limited T +852 36 69 82 00 F +852 36 69 82 56 sales.cn@epcos.com Romania TDK Austria GesmbH T +43 1 25 63 630 56 30 F +43 1 25 63 630 56 44 sales.romania@eu.tdk.com India, Bahrain, Bangladesh, Kuwait, Nepal, Oman, Qatar, Saudi Arabia, Sri Lanka, United Arab Emirates EPCOS India Private Ltd. T +91 80 40 39 06 15 +91 80 40 39 06 00 F +91 80 40 39 06 03 sales.in@epcos.com Israel TDK Sales Representative T +972 73 2676 317 sales.israel@eu.tdk.com Japan TDK Corporation T +81 3 68 52 73 00 inquiry@jp.tdk.com Korea EPCOS Korea LLC T +82 2 21 56 68 18 F +82 2 21 56 68 98 sales.kr@epcos.com Morocco, Tunisia TDK Electronics France SAS T +33 1 49 46 67 89 F +33 1 49 46 67 67 sales.france@eu.tdk.com South Africa TDK Sales Representative T +27 11 458 90 00 32 F +27 11 458 90 34 sales.southernafrica@epcos.com Malaysia EPCOS RDC SDN. BHD. T +60 6 79 98 168 F +60 6 79 98 162 sales.asean@epcos.com Philippines c/o TDK Electronics Philippines Corporation T +63 49 541 31 41 66 30 +63 49 541 31 41 66 31 F +63 49 541 31 40 sales.asean@epcos.com Singapore, Indonesia, Thailand, Vietnam EPCOS Pte., Ltd. T +65 68 41 20 11 F +65 67 44 69 92 sales.asean@epcos.com Taiwan EPCOS Taiwan Co. Ltd. T +886 2 26 55 76 76 F +886 2 27 82 03 89 sales.tw@epcos.com Americas USA, Canada, Mexico EPCOS Inc. T +1 732 9 06 43 00 F +1 732 9 06 43 95 sales.usa@epcos.com South America EPCOS do Brasil Ltda. T +55 11 32 89 95 99 Ext. 6851 F +55 11 32 89 99 40 sales.br@epcos.com Australia Australia, New Zealand TDK Sales Representative T +61 3 95 66 72 17 F +61 3 95 66 72 99 sales.au@epcos.com Africa Egypt TDK Europe GmbH T +90 216 5 69 81 01 F +90 216 4 64 07 56 sales.turkey@eu.tdk.com 04/16 The addresses of our worldwide distributors and regional sales offices are available at www.epcos.com/sales (c) EPCOS AG 2016, Corporate Communications, P.O.Box 80 17 09, 81617 Munich, Germany Reproduction, publication and dissemination of this publication and the information contained therein without EPCOS' prior express consent is prohibited. (c) EPCOS AG * A TDK Group Company Edition 2016 * Ordering No. EPC:25030-7600 * Printed in Germany * PP 06163.