IH5016MDE - Intersil Corporation

4-1

Features

• Switches Analog Signals Up to 20 Volts Peak-to-Peak

• Each Channel Complete - Interfaces with Most

Integrated Logic

• Switching Speeds Less Than 0.5µs

•I

D(OFF) Less Than 500pA Typical at 70oC

• Effective rDS(ON) - 5Ω to 50Ω

• Commercial and Military Temperature Range

Operation

Description

The IH5009 series of analog switches were designed to ﬁll

the need for an easy-to-use, inexpensive switch for both

industrial and military applications. Although low cost is a

primary design objective, performance and versatility have

not been sacriﬁced.

Each package contains up to four channels of analog gating

and is designed to eliminate the need for an external driver.

The odd numbered devices are designed to be driven

directly from TTL open collector logic (15 volts) while the

even numbered devices are driven directly from low level

TTL logic (5 volts). Each channel simulates a SPDT switch.

SPST switch action is obtained by leaving the diode cathode

unconnected; for SPDT action, the cathode should be

grounded (0V). The parts are intended for high performance

multiplexing and commutating usage. A logic “0” turns the

channel ON and a logic “1” turns the channel OFF.

Part Number Information

PART

NUMBER CHANNELS LOGIC

LEVEL PACKAGE PKG

NO.

IH5009 4 +15 DD, PD

IH5010 4 +5 DD, PD

IH5011 4 +15 DE, PE

IH5012 4 +5 DE, PE

IH5014 3 +5 DD, PD

IH5016 3 +5 DE, PE

IH5017 2 +15 PA

IH5018 2 +5 DD, PA

IH5019 2 +15 DE, PA

IH5020 2 +5 DE, PA

IH5022 1 +5 DD, PA

IH5024 1 +5 PA

NOTE: Mil-Temperaturerange(-55oCto125oC)available inceramic

packages only.

IH50XX M DE

PACKAGE

PA - 8 LEAD PDIP

PD - 14 LEAD PDIP

PE - 16 LEAD PDIP

DD - 14 LEAD CERDIP

DE - 16 LEAD CERDIP

TEMPERATURE RANGE

M = MILITARY (-55oC to 125oC)

C = COMMERCIAL (0oC to 70oC)

BASIC PART NUMBER

May 1999

CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures.

IH5009-5012, 5014,

5016-5020, 5022, 5024

Virtual Ground Analog Switch

File Number 3129.1

OBSOLETE PRODUCT

NO RECOMMENDED REPLACEMENT

Call Central Applications 1-800-442-7747

or email: centapp@harris.com

4-2

Functional Diagrams

(Numbers in brackets refer to CERDIP Packages)

IH5009, IH5010

(14 LEAD CERDIP, 14 LEAD PDIP) IH5011, IH5012

(16 LEAD CERDIP, 16 LEAD PDIP)

IH5014

(14 LEAD CERDIP, 14 LEAD PDIP) IH5016

(16 LEAD CERDIP, 16 LEAD PDIP)

IH5017 (8 LEAD PDIP)

IH5018 (8 LEAD PDIP, 14 LEAD CERDIP) IH5019, IH5020

(8 LEAD PDIP, 16 LEAD CERDIP)

IH5022

(8 LEAD PDIP, 14 LEAD CERDIP) IH5024

(8 LEAD PDIP)

IH5009 Series

4-3

Absolute Maximum Ratings Thermal Information

Positive Analog Signal Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . 30V

Negative Analog Signal Voltage . . . . . . . . . . . . . . . . . . . . . . . . .-15V

Diode Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10mA

Power Dissipation (Note) . . . . . . . . . . . . . . . . . . . . . . . . . . . 500mW

Operating Conditions

Temperature Range

5009C Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0oC to 70oC

5009M Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC

Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC

Maximum Lead Temperature (Soldering 10s). . . . . . . . . . . . . 300oC

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation

of the device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

NOTE: Dissipation rating assumes device is mounted with all leads welded or soldered to printed circuit board in ambient temperature below

75oC. For higher temperature, derate at rate of 5m/WoC.

Electrical Speciﬁcations (Per Channel)

PARAMETER (NOTE 1)

SYMBOL

(NOTE 4)

TEST

CONDITIONS (NOTE 2)

TYPE

-55oC (M)

0oC (C)

MIN/MAX

25oC 125oC(M)

70oC (C)

MIN/MAX UNITSTYP MIN/MAX

Input Current-ON IIN(ON) ALL VIN = 0V, ID = 2mA - 0.01 ±0.5 100 µA

Input Current-OFF IIN(OFF) 5V Logic Ckts VIN = +4.5V,

VA = ±10V - 0.04 ±0.5 20 nA

Input Current-OFF IIN(OFF) 15V Logic Ckts VIN = +11V,

VA = ±10V - 0.04 ±0.5 20 nA

Channel Control

Voltage-ON VIN(ON) 5V Logic Ckts Note 3 0.5 - 0.5 0.5 V

Channel Control

Voltage-ON VIN(ON) 15V Logic Ckts Note 3 1.5 - 1.5 1.5 V

Channel Control

Voltage-OFF VIN(OFF) 5V Logic Ckts Note 3 - - 4.5 4.5 V

Channel Control

Voltage-OFF VIN(OFF) 15V Logic Ckts Note 3 - - 11.0 11.0 V

Leakage Current-OFF ID(OFF) 5V Logic Ckts VIN = +4.5V,

VA = ±10V - 0.02 ±0.5 20 nA

Leakage Current-OFF ID(OFF) 15V Logic Ckts VIN = +11V,

VA = ±10V - 0.02 ±0.5 20 nA

Leakage Current-ON ID(ON) 5V Logic Ckts VIN = 0V, IS = 1mA - 0.30 ±1.0 1000 (M)

200 (C) nA

Leakage Current-ON ID(ON) 15V Logic Ckts VIN = 0V, IS = 1mA - 0.10 ±0.5 500 (M)

100 (C) nA

Leakage Current-ON ID(ON) 5V Logic Ckts VIN = 0V, IS = 2mA - - 1.0 10 µA

Leakage Current-ON ID(ON) 15V Logic Ckts VIN = 0V, IS = 2mA - - 2.0 100 µA

Drain-Source

ON-Resistance rDS(ON) 5V Logic Ckts ID = 2mA, VIN = 0.5V 150 90 150 385 (M)

240 (C) Ω

Drain-Source

ON-Resistance rDS(ON) 15V Logic Ckts ID = 2mA, VIN = 1.5V 100 80 100 250 (M)

160 (C) Ω

Turn-ON Time t(ON) All - 150 500 - ns

Turn-OFF Time t(OFF) All - 300 500 - ns

Cross Talk CT All f = 100Hz - 120 - - dB

NOTES:

1. (OFF) and (ON) subscript notation refers to the conduction state of the FET switch for the given test.

2. Refer to Figure 1 for definition of terms.

3. VIN(ON) and VIN(OFF) are test conditions guaranteed by the tests of rDS(ON) and ID(OFF) respectively.

4. “5V Logic CKTS” applies to even-numbered devices. “15V Logic CKTS” applies to odd-numbered devices.

IH5009 Series