H 2.5 mm x 7.6 mm Rectangular LED Lamps Technical Data HLMP-R100 HLMP-0300/0301 HLMP-0400/0401 HLMP-0503/0504 Features * Rectangular Light Emitting Surface * Flat High Sterance Emitting Surface * Stackable on 2.54 mm (0.100 inch) Centers * Ideal as Flush Mounted Panel Indicators * Ideal for Backlighting Legends * Long Life: Solid State Reliability * Choice of 4 Bright Colors DH AS AlGaAs Red High Efficiency Red Yellow High Performance Green * IC Compatible/Low Current Requirements The HLMP-R100 uses a double heterojunction (DH) absorbing substrate (AS) aluminum gallium arsenide (AlGaAs) red LED chip in a light red epoxy package. This combination produces outstanding light output over a wide range of drive currents. The HLMP-0300 and -0301 have a high efficiency red GaAsP on GaP LED chip in a light red epoxy package. The HLMP-0400 and -0401 provide a yellow GaAsP on GaP LED chip in a yellow epoxy package. The HLMP-0503 and -0504 provide a green GaP LED chip in a green epoxy package. Package Dimensions Description The HLMP-R100, -030X, -040X, -050X are solid state lamps encapsulated in a radial lead rectangular epoxy package. They utilize a tinted, diffused epoxy to provide high on-off contrast and a flat high intensity emitting surface. Borderless package design allows creation of uninterrupted light emitting areas. 5964-9378E 1-149 Axial Luminous Intensity I v (mcd) @ 20 mA DC Part Number Min. Typ. DH AlGaAs Red HLMP-R100 3.4 11.0 High Efficiency Red HLMP-0300 1.3 2.5 HLMP-0301 2.1 5.3 HLMP-0400 1.4 2.5 HLMP-0401 3.6 5.0 HLMP-0503 1.6 2.5 HLMP-0504 2.6 8.0 Color Yellow High Performance Green Absolute Maximum Ratings at TA = 25C HLMPR100 HLMP0300/-0301 HLMP0400/0401 HLMP0503/-0504 Units 300 90 60 90 mA Average Forward Current 20 25 20 25 mA [2] DC Current 30 30 20 30 mA Power Dissipation 87 135 85 135 mW 5 5 5 5 V 500 500 500 500 mA -55 to +100 -55 to +100 -20 to +100 C Parameter Peak Forward Current [1] Reverse Voltage (IR = 100 A) Transient Forward Current (10 s Pulse) [3] Operating Temperature Range Storage Temperature Range Lead Soldering Temperature (1.6 mm [0.063 in.] from body) -20 to +100 -55 to +100 -55 to +100 260C for 5 seconds Notes: 1. See Figure 5 to establish pulsed operating conditions. 2. For AlGaAs Red, Red, and Green Series derate linearly from 50C at 0.5 mA/C. For Yellow Series derate linearly from 50C at 0.2 mA/C. 3. The transient peak current is the maximum non-recurring peak current that can be applied to the device without damaging the LED die and wirebond. It is not recommended that the device be operated at peak current beyond the peak forward current listed in the Absolute Maximum Ratings. 1-150 Electrical/Optical Characteristics at TA = 25C HLMP-R100 Sym. Description 21/2 Included Angle Between Half Luminous Intensity Points HLMP -0300/-0301 HLMP -0400/-0401 HLMP -0503/-0504 Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Units Test Conditions 100 100 100 100 Deg. Note 1. Fig. 6 P Peak Wavelength 645 635 583 565 nm Measurement at Peak d Dominant Wavelength 637 626 585 569 nm Note 2 Spectral Line Halfwidth 20 40 36 28 nm s Speed of Response 30 90 90 500 ns C Capacitance 30 16 18 18 pF Thermal Resistance 260 260 260 260 C/W VF Forward Voltage 1.8 VR Reverse Breakdown Voltage v Luminous Efficacy 1/2 RJ-PIN 2.2 5.0 1.9 5.0 80 2.6 2.1 5.0 145 2.6 2.2 5.0 500 595 3.0 VF = 0; f = 1 MHz Junction to Cathode Lead V IF = 20 mA Figure 2. V IR = 100 A lm/W Note 3 Notes: 1. 1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 2. The dominant wavelength, d, is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 3. Radiant intensity, Ie, in watts/steradian, may be found from the equation Ie = Iv/v, where Iv is the luminous intensity in candelas and v is the luminous efficacy in lumens/watt. Figure 1. Relative Intensity vs. Wavelength. 1-151 Figure 2. Forward Current vs. Forward Voltage. VF (300 mA) for AlGaAs Red = 2.6 Volts Typical. Figure 3. Relative Luminous Intensity vs. Forward Current. Figure 5. Maximum Tolerable Peak Current vs. Peak Duration (IPEAK MAX Determined from Temperature Derated IDC MAX). Figure 6. Relative Luminous Intensity vs. Angular Displacement. 1-152 Figure 4. Relative Efficiency (Luminous Intensity per Unit Current) vs. Peak Current. v (300 mA) for AlGaAs Red = 0.7.