SDR-240-48 - Mean Well - Datasheet.Cloud

SPECIFICATION

MODEL

DCVOLTAGE

RATEDCURRENT

CURRENTRANGE

RATEDPOWER

PEAKCURRENT

PEAKPOWER Note.6

OUTPUT

VOLTAGE ADJ.RANGE

LINEREGULATION

LOADREGULATION

SETUP,RISETIME

HOLDUP TIME (Typ.)

VOLTAGERANGE

FREQUENCY RANGE

EFFICIENCY (Typ.) Note.8

INPUT

INRUSHCURRENT (Typ.)

LEAKAGECURRENT

OVERTEMPERATURE

SAFETY STANDARDS

HARMONICCURRENT

EMSIMMUNITY

WORKINGTEMP. Note.5

DCOKREALY CONTACTRATINGS(max.)

WORKINGHUMIDITY

STORAGETEMP.,HUMIDITY

TEMP.COEFFICIENT

VIBRATION

MTBF

DIMENSIONOTHERS

NOTE

PACKING

OVERLOAD

OVERVOLTAGE

ACCURRENT (Typ.)

1500ms,60ms/230VAC30 atfullload00ms,60ms/115VAC

20ms/230VAC20ms/115VACatfullload

88~264VAC124~370VDC

47~63Hz

94%

0.93/230VAC0.99/115VACatfullload

2.6A/115VAC1.3A/230VAC

56~65V

33A/115VAC65A/230VAC

<1mA /240VAC

Normallyw morethan3 andthenshutdowno/pvoltagewithauto-recoveryorkswithin110~150%ratedoutputpowerfor seconds

29~33V

>150%ratedpower,constantcurrentlimitingwithauto-recoverywithin2secondsandmaycausetoshutdownifover2seconds

Protectiontype:Shutdowno/pvoltagewithauto-recovery

95 5 (TSW:detectonheatsinkofpowerswitch)

Protectiontype:Shutdowno/pvoltage,recoversautomaticallyaftertemperaturegoesdown

UL508 TUVEN60950-1approved,

CompliancetoEN55022(CISPR22)ClassB

CompliancetoEN61000-3-2,-3

CompliancetoEN61000-4-2,3,4,5,6,8,11,ENV50204,EN55024,EN61000-6-2(EN50082-2),EN61204-3,heavyindustrylevel,

criteria A,SEMIF47,GL approved

-25~+70 (Refertooutputloadderatingcurve)

60Vdc/0.3A,30Vdc/1A,30Vac/0.5A resistiveload

20~95%RHnon-condensing

-40~+85 ,10~95%RH

0.03%/ (0~50

Component:10~500Hz,2G10min./1cycle,60min.eachalongX, Y,Zaxes;Mounting:CompliancetoIEC60068-2-6

169.3Khrsmin.MIL-HDBK-217F(25 )

63*125.2*113.5mm(W*H*D)

1.03Kg;12pcs/13.4Kg/1.06CUFT

POWERFACTOR (Typ.)

SDR-240-48

48V

0~5A

240W

7.5A

120mVp-p

48~55V

1.0%

0.5%

1.0%

SDR-240-24

24V

10A

0~10A

240W

15A

360W(3sec.)

100mVp-p

24~28V

1.0%

0.5%

1.0%

Features :

SDR-240 series

WITHSTANDVOLTAGE

ISOLATIONRESISTANCE

I/P-O/P:3KVACI/P-FG:1.5KVACO/P-FG:0.5KVAC O/P-DCOK:0.5KVAC

I/P-O/P,I/P-FG,O/P-FG:>100MOhms/500VDC/25 /70%RH

EMICONDUCTION&RADIATION

ENVIRONMENT

SAFETY &

FUNCTION

EMC

(Note4)

PROTECTION

RIPPLE&NOISE(max.) Note.2

VOLTAGETOLERANCE Note.3

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets

EMC directives.

5. Installation clearances : 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power.

In case the adjacent device is a heat source, 15mm clearance is recommended.

6. 3 seconds max., please refer to peak loading curves.

7. Derating may be needed under low input voltage. Please check the derating curve for more details.

8. After 30 minutes of burn-in.

240WSingleOutputIndustrialDINRAIL withPFCFunction

High efficiency 94% and low power dissipation

Built-in active PFC function, PF>0.93

Protections: Short circuit / Overload / Over voltage / Over temperature

Cooling by free air convection

Can be installed on DIN rail TS-35/7.5 or 15

UL 508 (industrial control equipment) approved

EN61000-6-2(EN50082-2) industrial immunity level

100% full load burn-in test

3 years warranty

150% peak load capability

Built-in DC OK relay contact

SEMIF47

FileName:SDR-240-SPEC2010-12-07

http://store.iiic.cc/