LPC1768FBD100K - NXP SEMICONDUCTORS

1. General description

The LPC1769/68/67/66/65/64/63 are ARM Cortex-M3 based microcontrollers for

embedded applications featuring a high level of integration and low power consumption.

The Arm Cortex-M3 is a next generation core that offers system enhancements such as

enhanced debug features and a higher level of support block integration.

The LPC1768/67/66/65/64/63 operate at CPU frequencies of up to 100 MHz. The

LPC1769 operates at CPU frequencies of up to 120 MHz. The Arm Cortex-M3 CPU

incorporates a 3-stage pipeline and uses a Harvard architecture with separate local

instruction and data buses as well as a third bus for peripherals. The Arm Cortex-M3 CPU

also includes an internal prefetch unit that supports speculative branching.

The peripheral complement of the LPC1769/68/67/66/65/64/63 includes up to 512 kB of

flash memory, up to 64 kB of data memory, Ethernet MAC, USB Device/Host/OTG

interface, 8-channel general purpose DMA controller, 4 UARTs, 2 CAN channels, 2 SSP

controllers, SPI interface, 3 I2C-bus interfaces, 2-input plus 2-output I2S-bus interface,

8-channel 12-bit ADC, 10-bit DAC, motor control PWM, Quadrature Encoder interface,

four general purpose timers, 6-output general purpose PWM, ultra-low power Real-Time

Clock (RTC) with separate battery supply, and up to 70 general purpose I/O pins.

The LPC1769/68/67/66/65/64/63 are pin-compatible to the 100-pin LPC236x Arm7-based

microcontroller series.

For additional documentation, see Section 19 “References”.

2. Features and benefits

Arm Cortex-M3 processor, running at frequencies of up to 100 MHz

(LPC1768/67/66/65/64/63) or of up to 120 MHz (LPC1769). A Memory Protection Unit

(MPU) supporting eight regions is included.

Arm Cortex-M3 built-in Nested Vectored Interrupt Controller (NVIC).

Up to 512 kB on-chip flash programming memory. Enhanced flash memory accelerator

enables high-speed 120 MHz operation with zero wait states.

In-System Programming (ISP) and In-Application Programming (IAP) via on-chip

bootloader software.

On-chip SRAM includes:

32/16 kB of SRAM on the CPU with local code/data bus for high-performance CPU

access.

LPC1769/68/67/66/65/64/63

32-bit Arm Cortex®-M3 microcontroller; up to 512 kB flash and

64 kB SRAM with Ethernet, USB 2.0 Host/Device/OTG, CAN

Rev. 9.10 — 8 September 2020 Product data sheet

Product data sheet Rev. 9.10 — 8 September 2020 2 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Two/one 16 kB SRAM blocks with separate access paths for higher throughput.

These SRAM blocks may be used for Ethernet, USB, and DMA memory, as well as

for general purpose CPU instruction and data storage.

Eight channel General Purpose DMA controller (GPDMA) on the AHB multilayer

matrix that can be used with SSP, I2S-bus, UART, Analog-to-Digital and

Digital-to-Analog converter peripherals, timer match signals, and for

memory-to-memory transfers.

Multilayer AHB matrix interconnect provides a separate bus for each AHB master.

AHB masters include the CPU, General Purpose DMA controller, Ethernet MAC, and

the USB interface. This interconnect provides communication with no arbitration

delays.

Split APB bus allows high throughput with few stalls between the CPU and DMA.

Serial interfaces:

Ethernet MAC with RMII interface and dedicated DMA controller. (Not available on

all parts, see Table 2.)

USB 2.0 full-speed device/Host/OTG controller with dedicated DMA controller and

on-chip PHY for device, Host, and OTG functions. (Not available on all parts, see

Table 2.)

Four UARTs with fractional baud rate generation, internal FIFO, and DMA support.

One UART has modem control I/O and RS-485/EIA-485 support, and one UART

has IrDA support.

CAN 2.0B controller with two channels. (Not available on all parts, see Table 2.)

SPI controller with synchronous, serial, full duplex communication and

programmable data length.

Two SSP controllers with FIFO and multi-protocol capabilities. The SSP interfaces

can be used with the GPDMA controller.

Three enhanced I2C bus interfaces, one with an open-drain output supporting full

I2C specification and Fast mode plus with data rates of 1 Mbit/s, two with standard

port pins. Enhancements include multiple address recognition and monitor mode.

I2S (Inter-IC Sound) interface for digital audio input or output, with fractional rate

control. The I2S-bus interface can be used with the GPDMA. The I2S-bus interface

supports 3-wire and 4-wire data transmit and receive as well as master clock

input/output. (Not available on all parts, see Table 2.)

Other peripherals:

70 (100 pin package) General Purpose I/O (GPIO) pins with configurable

pull-up/down resistors. All GPIOs support a new, configurable open-drain operating

mode. The GPIO block is accessed through the AHB multilayer bus for fast access

and located in memory such that it supports Cortex-M3 bit banding and use by the

General Purpose DMA Controller.

12-bit Analog-to-Digital Converter (ADC) with input multiplexing among eight pins,

conversion rates up to 200 kHz, and multiple result registers. The 12-bit ADC can

be used with the GPDMA controller.

10-bit Digital-to-Analog Converter (DAC) with dedicated conversion timer and DMA

support. (Not available on all parts, see Table 2)

Four general purpose timers/counters, with a total of eight capture inputs and ten

compare outputs. Each timer block has an external count input. Specific timer

events can be selected to generate DMA requests.

One motor control PWM with support for three-phase motor control.

Product data sheet Rev. 9.10 — 8 September 2020 3 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Quadrature encoder interface that can monitor one external quadrature encoder.

One standard PWM/timer block with external count input.

RTC with a separate power domain and dedicated RTC oscillator. The RTC block

includes 20 bytes of battery-powered backup registers.

WatchDog Timer (WDT). The WDT can be clocked from the internal RC oscillator,

the RTC oscillator, or the APB clock.

Arm Cortex-M3 system tick timer, including an external clock input option.

Repetitive interrupt timer provides programmable and repeating timed interrupts.

Each peripheral has its own clock divider for further power savings.

Standard JTAG debug interface for compatibility with existing tools. Serial Wire Debug

and Serial Wire Trace Port options. Boundary Scan Description Language (BSDL) is

not available for this device.

Emulation trace module enables non-intrusive, high-speed real-time tracing of

instruction execution.

Integrated PMU (Power Management Unit) automatically adjusts internal regulators to

minimize power consumption during Sleep, Deep sleep, Power-down, and Deep

power-down modes.

Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep power-down.

Single 3.3 V power supply (2.4 V to 3.6 V).

Four external interrupt inputs configurable as edge/level sensitive. All pins on Port 0

and Port 2 can be used as edge sensitive interrupt sources.

Non-maskable Interrupt (NMI) input.

Clock output function that can reflect the main oscillator clock, IRC clock, RTC clock,

CPU clock, and the USB clock.

The Wake-up Interrupt Controller (WIC) allows the CPU to automatically wake up from

any priority interrupt that can occur while the clocks are stopped in deep sleep,

Power-down, and Deep power-down modes.

Processor wake-up from Power-down mode via any interrupt able to operate during

Power-down mode (includes external interrupts, RTC interrupt, USB activity, Ethernet

wake-up interrupt, CAN bus activity, Port 0/2 pin interrupt, and NMI).

Brownout detect with separate threshold for interrupt and forced reset.

Power-On Reset (POR).

Crystal oscillator with an operating range of 1 MHz to 25 MHz.

4 MHz internal RC oscillator trimmed to 1 % accuracy that can optionally be used as a

system clock.

PLL allows CPU operation up to the maximum CPU rate without the need for a

high-frequency crystal. May be run from the main oscillator, the internal RC oscillator,

or the RTC oscillator.

USB PLL for added flexibility.

Code Read Protection (CRP) with different security levels.

Unique device serial number for identification purposes.

Available as LQFP100 (14 mm  14 mm  1.4 mm), TFBGA1001 (9 mm  9 mm  0.7

mm), and WLCSP100 (5.07  5.07  0.53 mm) package.

1. LPC1768/65 only.

Product data sheet Rev. 9.10 — 8 September 2020 4 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

3. Applications

4. Ordering information

4.1 Ordering options

eMetering Alarm systems

Lighting White goods

Industrial networking Motor control

Table 1. Ordering information

Type number Package

Name Description Version

LPC1769FBD100 LQFP100 plastic low profile quad flat package; 100 leads; body 14  14  1.4 mm SOT407-1

LPC1768FBD100 LQFP100 plastic low profile quad flat package; 100 leads; body 14  14  1.4 mm SOT407-1

LPC1768FET100 TFBGA100 plastic thin fine-pitch ball grid array package; 100 balls; body 9  9  0.7 mm SOT926-1

LPC1768UK WLCSP100 wafer level chip-scale package; 100 balls; 5.07  5.07  0.53 mm -

LPC1767FBD100 LQFP100 plastic low profile quad flat package; 100 leads; body 14  14  1.4 mm SOT407-1

LPC1766FBD100 LQFP100 plastic low profile quad flat package; 100 leads; body 14  14  1.4 mm SOT407-1

LPC1765FBD100 LQFP100 plastic low profile quad flat package; 100 leads; body 14  14  1.4 mm SOT407-1

LPC1765FET100 TFBGA100 plastic thin fine-pitch ball grid array package; 100 balls; body 9  9  0.7 mm SOT926-1

LPC1764FBD100 LQFP100 plastic low profile quad flat package; 100 leads; body 14  14  1.4 mm SOT407-1

LPC1763FBD100 LQFP100 plastic low profile quad flat package; 100 leads; body 14  14  1.4 mm SOT407-1

Table 2. Ordering options

Type number

Device order

part number

Flash (kB)

SRAM in kB

Ethernet

USB

CAN

I2S

DAC

GPIO

Maximum CPU

operating frequency

(MHz)

CPU

AHB SRAM0

AHB SRAM1

Total

LPC1769FBD100 LPC1769FBD100,551 512 32 16 16 64 yes Device/Host/OTG 2 yes yes 70 120

LPC1768FBD100 LPC1768FBD100/CP32 512 32 16 16 64 yes Device/Host/OTG 2 yes yes 70 100

LPC1768FET100 LPC1768FET100Z 512 32 16 16 64 yes Device/Host/OTG 2 yes yes 70 100

LPC1768UK LPC1768UKZ 512 32 16 16 64 yes Device/Host/OTG 2 yes yes 70 100

LPC1767FBD100 LPC1767FBD100,551 512 32 16 16 64 yes no no yes yes 70 100

LPC1766FBD100 LPC1766FBD100,551 256 32 16 16 64 yes Device/Host/OTG 2 yes yes 70 100

LPC1765FBD100 LPC1765FBD100/3271 256 32 16 16 64 no Device/Host/OTG 2 yes yes 70 100

LPC1765FET100 LPC1765FET100,551 256 32 16 16 64 no Device/Host/OTG 2 yes yes 70 100

LPC1764FBD100 LPC1764FBD100,551 128 16 16 - 32 yes Device only 2 no no 70 100

LPC1763FBD100 LPC1763FBD100K 256 32 16 16 64 no no no yes yes 70 100

Product data sheet Rev. 9.10 — 8 September 2020 5 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

5. Marking

The LPC176x devices typically have the following top-side marking:

LPC176xxxx

xxxxxxx

xxYYWWR[x]

The last/second to last letter in the third line (field ‘R’) will identify the device revision. This

data sheet covers the following revisions of the LPC176x:

Field ‘YY’ states the year the device was manufactured. Field ‘WW’ states the week the

device was manufactured during that year.

Table 3. Device revision table

Revision identifier (R) Revision description

‘-’ Initial device revision

‘A’ Second device revision

‘C’ Third device revision (LQFP100, TFBGA100

ONLY)

Product data sheet Rev. 9.10 — 8 September 2020 6 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

6. Block diagram

(1) Not available on all parts. See Table 2.

Fig 1. Block diagram

SRAM 32/64 kB

ARM

CORTEX-M3

TEST/DEBUG

INTERFACE

EMULATION

TRACE MODULE

FLASH

ACCELERATOR

FLASH

512/256/128 kB

DMA

CONTROLLER

ETHERNET

CONTROLLER

WITH DMA(1)

USB HOST/

DEVICE/OTG

CONTROLLER

WITH DMA(1)

I-code

bus D-code

bus system

bus

AHB TO

APB

BRIDGE 0

HIGH-SPEED

GPIO AHB TO

APB

BRIDGE 1

CLOCK

GENERATION,

POWER CONTROL,

SYSTEM

FUNCTIONS

XTAL1

XTAL2 RESET

clocks and

controls

JTAG

interface

debug

port

USB PHY

SSP0

UART2/3

I2S(1)

I2C2

RI TIMER

TIMER2/3

EXTERNAL INTERRUPTS

SYSTEM CONTROL

MOTOR CONTROL PWM

QUADRATURE ENCODER

SSP1

UART0/1

CAN1/2(1)

I2C0/1

SPI0

TIMER 0/1

WDT

PWM1

12-bit ADC

PIN CONNECT

GPIO INTERRUPT CONTROL

RTC

BACKUP REGISTERS

32 kHz

OSCILLATOR

APB slave group 1

APB slave group 0

DAC(1)

RTC POWER DOMAIN

LPC1769/68/67/

66/65/64/63

master master master

002aad944

slaveslave slave slave

slave ROM

slave

MULTILAYER AHB MATRIX

P0 to

SDA2

SCL2

SCK0

SSEL0

MISO0

MOSI0

SCK1

SSEL1

MISO1

MOSI1 RXD2/3

TXD2/3

PHA, PHB

INDEX

EINT[3:0

]

AOUT

MCOA[2:

MCOB[2:

MCI[2:0]

MCABOR

4 MAT

2 MAT

2 CAP2

2 CAP3

3 I2SRX

3 I2STX

TX_MCL

RX_MCL

RTCX1

RTCX2

VBAT

PWM1[7:0]

2 MAT0/1

2 CAP0/1

RD1/2

TD1/2

SDA0/1

SCL0/1

AD0[7:0]

SCK/SSEL

OSI/MISO

8 UART1

XD0/TXD0

P0, P2

PCAP1[1:0]

RMII pins USB pins

CLKOUT

MPU

= connected to DMA

Product data sheet Rev. 9.10 — 8 September 2020 7 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

7. Pinning information

7.1 Pinning

Fig 2. Pin configuration LQFP100 package

Fig 3. Pin configuration TFBGA100 package

LPC176xFBD100

100

002aad945

002aaf723

LPC1768/65FET100

Transparent top view

24681013579

ball A1

index area

Product data sheet Rev. 9.10 — 8 September 2020 8 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Fig 4. Pin configuration WLCSP100 package

Transparent top view

2345678910

LPC1768UK

bump A1

index area

aaa-009522

Table 4. Pin allocation table TFBGA100

Pin Symbol Pin Symbol Pin Symbol Pin Symbol

Row A

1 TDO/SWO 2 P0[3]/RXD0/AD0[6] 3 VDD(3V3) 4 P1[4]/ENET_TX_EN

5 P1[10]/ENET_RXD1 6 P1[16]/ENET_MDC 7 VDD(REG)(3V3) 8 P0[4]/I2SRX_CLK/

RD2/CAP2[0]

9 P0[7]/I2STX_CLK/

SCK1/MAT2[1]

10 P0[9]/I2STX_SDA/

MOSI1/MAT2[3]

11 - 12 -

Row B

1 TMS/SWDIO 2 RTCK 3 VSS 4 P1[1]/ENET_TXD1

5 P1[9]/ENET_RXD0 6 P1[17]/

ENET_MDIO

SS 8 P0[6]/I2SRX_SDA/

SSEL1/MAT2[0]

9 P2[0]/PWM1[1]/TXD1 10 P2[1]/PWM1[2]/RXD1 11 - 12 -

Row C

1 TCK/SWDCLK 2 TRST 3 TDI 4 P0[2]/TXD0/AD0[7]

5 P1[8]/ENET_CRS 6 P1[15]/

ENET_REF_CLK

7 P4[28]/RX_MCLK/

MAT2[0]/TXD3

8 P0[8]/I2STX_WS/

MISO1/MAT2[2]

SS 10 VDD(3V3) 11 - 12 -

Row D

1 P0[24]/AD0[1]/

I2SRX_WS/CAP3[1]

2 P0[25]/AD0[2]/

I2SRX_SDA/TXD3

3 P0[26]/AD0[3]/

AOUT/RXD3

4 n.c.

5 P1[0]/ENET_TXD0 6 P1[14]/ENET_RX_ER 7 P0[5]/I2SRX_WS/

TD2/CAP2[1]

8 P2[2]/PWM1[3]/

CTS1/TRACEDATA[3]

9 P2[4]/PWM1[5]/

DSR1/TRACEDATA[1]

10 P2[5]/PWM1[6]/

DTR1/TRACEDATA[0]

11 - 12 -

Row E

SSA 2V

DDA 3 VREFP 4 n.c.

5 P0[23]/AD0[0]/

I2SRX_CLK/CAP3[0]

6 P4[29]/TX_MCLK/

MAT2[1]/RXD3

7 P2[3]/PWM1[4]/

DCD1/TRACEDATA[2]

8 P2[6]/PCAP1[0]/

RI1/TRACECLK

Product data sheet Rev. 9.10 — 8 September 2020 9 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

9 P2[7]/RD2/RTS1 10 P2[8]/TD2/TXD2 11 - 12 -

Row F

1 VREFN 2 RTCX1 3 RESET 4 P1[31]/SCK1/

AD0[5]

5 P1[21]/MCABORT/

PWM1[3]/SSEL0

6 P0[18]/DCD1/

MOSI0/MOSI

7 P2[9]/USB_CONNECT/

RXD2

8 P0[16]/RXD1/

SSEL0/SSEL

9 P0[17]/CTS1/

MISO0/MISO

10 P0[15]/TXD1/

SCK0/SCK

11 - 12 -

Row G

1 RTCX2 2 VBAT 3 XTAL2 4 P0[30]/USB_D

5 P1[25]/MCOA1/

MAT1[1]

6 P1[29]/MCOB2/

PCAP1[1]/MAT0[1]

SS 8 P0[21]/RI1/RD1

9 P0[20]/DTR1/SCL1 10 P0[19]/DSR1/SDA1 11 - 12 -

Row H

1 P1[30]/VBUS/

AD0[4]

2 XTAL1 3 P3[25]/MAT0[0]/

PWM1[2]

4 P1[18]/USB_UP_LED/

PWM1[1]/CAP1[0]

5 P1[24]/MCI2/

PWM1[5]/MOSI0

DD(REG)(3V3) 7 P0[10]/TXD2/

SDA2/MAT3[0]

8 P2[11]/EINT1/

I2STX_CLK

DD(3V3) 10 P0[22]/RTS1/TD1 11 - 12 -

Table 4. Pin allocation table TFBGA100 …continued

Pin Symbol Pin Symbol Pin Symbol Pin Symbol

Product data sheet Rev. 9.10 — 8 September 2020 10 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

7.2 Pin description

Row J

1 P0[28]/SCL0/

USB_SCL

2 P0[27]/SDA0/

USB_SDA

3 P0[29]/USB_D+ 4 P1[19]/MCOA0/

USB_PPWR/

CAP1[1]

5 P1[22]/MCOB0/

USB_PWRD/

MAT1[0]

SS 7 P1[28]/MCOA2/

PCAP1[0]/

MAT0[0]

8 P0[1]/TD1/RXD3/SCL1

9 P2[13]/EINT3/

I2STX_SDA

10 P2[10]/EINT0/NMI 11 - 12 -

Row K

1 P3[26]/STCLK/

MAT0[1]/PWM1[3]

DD(3V3) 3V

SS 4 P1[20]/MCI0/

PWM1[2]/SCK0

5 P1[23]/MCI1/

PWM1[4]/MISO0

6 P1[26]/MCOB1/

PWM1[6]/CAP0[0]

7 P1[27]/CLKOUT

/USB_OVRCR/

CAP0[1]

8 P0[0]/RD1/TXD3/SDA1

9 P0[11]/RXD2/

SCL2/MAT3[1]

10 P2[12]/EINT2/

I2STX_WS

11 - 12 -

Table 4. Pin allocation table TFBGA100 …continued

Pin Symbol Pin Symbol Pin Symbol Pin Symbol

Table 5. Pin description

Symbol Pin/ball Type Description

LQFP100

TFBGA100

WLCSP100

P0[0] to P0[31] I/O Port 0: Port 0 is a 32-bit I/O port with individual direction controls for

each bit. The operation of port 0 pins depends upon the pin function

selected via the pin connect block. Pins 12, 13, 14, and 31 of this

port are not available.

P0[0]/RD1/TXD3/

SDA1

46 K8 H10 [1] I/O P0[0] — General purpose digital input/output pin.

IRD1 — CAN1 receiver input. (LPC1769/68/66/65/64 only).

OTXD3 — Transmitter output for UART3.

I/O SDA1 — I2C1 data input/output. (This is not an I2C-bus compliant

open-drain pin).

P0[1]/TD1/RXD3/

SCL1

47 J8 H9 [1] I/O P0[1] — General purpose digital input/output pin.

OTD1 — CAN1 transmitter output. (LPC1769/68/66/65/64 only).

IRXD3 — Receiver input for UART3.

I/O SCL1 — I2C1 clock input/output. (This is not an I2C-bus compliant

open-drain pin).

P0[2]/TXD0/AD0[7] 98 C4 B1 [2] I/O P0[2] — General purpose digital input/output pin.

OTXD0 — Transmitter output for UART0.

IAD0[7] — A/D converter 0, input 7.

P0[3]/RXD0/AD0[6] 99 A2 C3 [2] I/O P0[3] — General purpose digital input/output pin.

IRXD0 — Receiver input for UART0.

IAD0[6] — A/D converter 0, input 6.

Product data sheet Rev. 9.10 — 8 September 2020 11 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

P0[4]/

I2SRX_CLK/

RD2/CAP2[0]

81 A8 G2 [1] I/O P0[4] — General purpose digital input/output pin.

I/O I2SRX_CLK — Receive Clock. It is driven by the master and

received by the slave. Corresponds to the signal SCK in the I2S-bus

specification. (LPC1769/68/67/66/65/63 only).

IRD2 — CAN2 receiver input. (LPC1769/68/66/65/64 only).

ICAP2[0] — Capture input for Timer 2, channel 0.

P0[5]/

I2SRX_WS/

TD2/CAP2[1]

80 D7 H1 [1] I/O P0[5] — General purpose digital input/output pin.

I/O I2SRX_WS — Receive Word Select. It is driven by the master and

received by the slave. Corresponds to the signal WS in the I2S-bus

specification. (LPC1769/68/67/66/65/63 only).

OTD2 — CAN2 transmitter output. (LPC1769/68/66/65/64 only).

ICAP2[1] — Capture input for Timer 2, channel 1.

P0[6]/

I2SRX_SDA/

SSEL1/MAT2[0]

79 B8 G3 [1] I/O P0[6] — General purpose digital input/output pin.

I/O I2SRX_SDA — Receive data. It is driven by the transmitter and read

by the receiver. Corresponds to the signal SD in the I2S-bus

specification. (LPC1769/68/67/66/65/63 only).

I/O SSEL1 — Slave Select for SSP1.

OMAT2[0] — Match output for Timer 2, channel 0.

P0[7]/

I2STX_CLK/

SCK1/MAT2[1]

78 A9 J1 [1] I/O P0[7] — General purpose digital input/output pin.

I/O I2STX_CLK — Transmit Clock. It is driven by the master and

received by the slave. Corresponds to the signal SCK in the I2S-bus

specification. (LPC1769/68/67/66/65/63 only).

I/O SCK1 — Serial Clock for SSP1.

OMAT2[1] — Match output for Timer 2, channel 1.

P0[8]/

I2STX_WS/

MISO1/MAT2[2]

77 C8 H2 [1] I/O P0[8] — General purpose digital input/output pin.

I/O I2STX_WS — Transmit Word Select. It is driven by the master and

received by the slave. Corresponds to the signal WS in the I2S-bus

specification. (LPC1769/68/67/66/65/63 only).

I/O MISO1 — Master In Slave Out for SSP1.

OMAT2[2] — Match output for Timer 2, channel 2.

P0[9]/

I2STX_SDA/

MOSI1/MAT2[3]

76 A10 H3 [1] I/O P0[9] — General purpose digital input/output pin.

I/O I2STX_SDA — Transmit data. It is driven by the transmitter and

read by the receiver. Corresponds to the signal SD in the I2S-bus

specification. (LPC1769/68/67/66/65/63 only).

I/O MOSI1 — Master Out Slave In for SSP1.

OMAT2[3] — Match output for Timer 2, channel 3.

P0[10]/TXD2/

SDA2/MAT3[0]

48 H7 H8 [1] I/O P0[10] — General purpose digital input/output pin.

OTXD2 — Transmitter output for UART2.

I/O SDA2 — I2C2 data input/output (this is not an open-drain pin).

OMAT3[0] — Match output for Timer 3, channel 0.

Table 5. Pin description …continued

Symbol Pin/ball Type Description

LQFP100

TFBGA100

WLCSP100

Product data sheet Rev. 9.10 — 8 September 2020 12 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

P0[11]/RXD2/

SCL2/MAT3[1]

49 K9 J10 [1] I/O P0[11] — General purpose digital input/output pin.

IRXD2 — Receiver input for UART2.

I/O SCL2 — I2C2 clock input/output (this is not an open-drain pin).

OMAT3[1] — Match output for Timer 3, channel 1.

P0[15]/TXD1/

SCK0/SCK

62 F10 H6 [1] I/O P0[15] — General purpose digital input/output pin.

OTXD1 — Transmitter output for UART1.

I/O SCK0 — Serial clock for SSP0.

I/O SCK — Serial clock for SPI.

P0[16]/RXD1/

SSEL0/SSEL

63 F8 J5 [1] I/O P0[16] — General purpose digital input/output pin.

IRXD1 — Receiver input for UART1.

I/O SSEL0 — Slave Select for SSP0.

I/O SSEL — Slave Select for SPI.

P0[17]/CTS1/

MISO0/MISO

61 F9 K6 [1] I/O P0[17] — General purpose digital input/output pin.

ICTS1 — Clear to Send input for UART1.

I/O MISO0 — Master In Slave Out for SSP0.

I/O MISO — Master In Slave Out for SPI.

P0[18]/DCD1/

MOSI0/MOSI

60 F6 J6 [1] I/O P0[18] — General purpose digital input/output pin.

IDCD1 — Data Carrier Detect input for UART1.

I/O MOSI0 — Master Out Slave In for SSP0.

I/O MOSI — Master Out Slave In for SPI.

P0[19]/DSR1/

SDA1

59 G10 K7 [1] I/O P0[19] — General purpose digital input/output pin.

IDSR1 — Data Set Ready input for UART1.

I/O SDA1 — I2C1 data input/output (this is not an I2C-bus compliant

open-drain pin).

P0[20]/DTR1/SCL1 58 G9 J7 [1] I/O P0[20] — General purpose digital input/output pin.

ODTR1 — Data Terminal Ready output for UART1. Can also be

configured to be an RS-485/EIA-485 output enable signal.

I/O SCL1 — I2C1 clock input/output (this is not an I2C-bus compliant

open-drain pin).

P0[21]/RI1/RD1 57 G8 H7 [1] I/O P0[21] — General purpose digital input/output pin.

IRI1 — Ring Indicator input for UART1.

IRD1 — CAN1 receiver input. (LPC1769/68/66/65/64 only).

P0[22]/RTS1/TD1 56 H10 K8 [1] I/O P0[22] — General purpose digital input/output pin.

ORTS1 — Request to Send output for UART1. Can also be

configured to be an RS-485/EIA-485 output enable signal.

OTD1 — CAN1 transmitter output. (LPC1769/68/66/65/64 only).

Table 5. Pin description …continued

Symbol Pin/ball Type Description

LQFP100

TFBGA100

WLCSP100

Product data sheet Rev. 9.10 — 8 September 2020 13 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

P0[23]/AD0[0]/

I2SRX_CLK/

CAP3[0]

9E5D5

[2] I/O P0[23] — General purpose digital input/output pin.

IAD0[0] — A/D converter 0, input 0.

I/O I2SRX_CLK — Receive Clock. It is driven by the master and

received by the slave. Corresponds to the signal SCK in the I2S-bus

specification. (LPC1769/68/67/66/65/63 only).

ICAP3[0] — Capture input for Timer 3, channel 0.

P0[24]/AD0[1]/

I2SRX_WS/

CAP3[1]

8D1B4

[2] I/O P0[24] — General purpose digital input/output pin.

IAD0[1] — A/D converter 0, input 1.

I/O I2SRX_WS — Receive Word Select. It is driven by the master and

received by the slave. Corresponds to the signal WS in the I2S-bus

specification. (LPC1769/68/67/66/65/63 only).

ICAP3[1] — Capture input for Timer 3, channel 1.

P0[25]/AD0[2]/

I2SRX_SDA/

TXD3

7D2A3

[2] I/O P0[25] — General purpose digital input/output pin.

IAD0[2] — A/D converter 0, input 2.

I/O I2SRX_SDA — Receive data. It is driven by the transmitter and read

by the receiver. Corresponds to the signal SD in the I2S-bus

specification. (LPC1769/68/67/66/65/63 only).

OTXD3 — Transmitter output for UART3.

P0[26]/AD0[3]/

AOUT/RXD3

6D3C5

[3] I/O P0[26] — General purpose digital input/output pin.

IAD0[3] — A/D converter 0, input 3.

OAOUT — DAC output (LPC1769/68/67/66/65/63 only).

IRXD3 — Receiver input for UART3.

P0[27]/SDA0/

USB_SDA

25 J2 C8 [4] I/O P0[27] — General purpose digital input/output pin. Output is

open-drain.

I/O SDA0 — I2C0 data input/output. Open-drain output (for I2C-bus

compliance).

I/O USB_SDA — USB port I2C serial data (OTG transceiver,

LPC1769/68/66/65 only).

P0[28]/SCL0/

USB_SCL

24 J1 B9 [4] I/O P0[28] — General purpose digital input/output pin. Output is

open-drain.

I/O SCL0 — I2C0 clock input/output. Open-drain output (for I2C-bus

compliance).

I/O USB_SCL — USB port I2C serial clock (OTG transceiver,

LPC1769/68/66/65 only).

P0[29]/USB_D+ 29 J3 B10 [5] I/O P0[29] — General purpose digital input/output pin.

I/O USB_D+ — USB bidirectional D+ line. (LPC1769/68/66/65/64 only).

P0[30]/USB_D30 G4 C9 [5] I/O P0[30] — General purpose digital input/output pin.

I/O USB_D — USB bidirectional D line. (LPC1769/68/66/65/64 only).

Table 5. Pin description …continued

Symbol Pin/ball Type Description

LQFP100

TFBGA100

WLCSP100

Product data sheet Rev. 9.10 — 8 September 2020 14 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

P1[0] to P1[31] I/O Port 1: Port 1 is a 32-bit I/O port with individual direction controls for

each bit. The operation of port 1 pins depends upon the pin function

selected via the pin connect block. Pins 2, 3, 5, 6, 7, 11, 12, and 13

of this port are not available.

P1[0]/

ENET_TXD0

95 D5 C1 [1] I/O P1[0] — General purpose digital input/output pin.

OENET_TXD0 — Ethernet transmit data 0. (LPC1769/68/67/66/64

only).

P1[1]/

ENET_TXD1

94 B4 C2 [1] I/O P1[1] — General purpose digital input/output pin.

OENET_TXD1 — Ethernet transmit data 1. (LPC1769/68/67/66/64

only).

P1[4]/

ENET_TX_EN

93 A4 D2 [1] I/O P1[4] — General purpose digital input/output pin.

OENET_TX_EN — Ethernet transmit data enable.

(LPC1769/68/67/66/64 only).

P1[8]/

ENET_CRS

92 C5 D1 [1] I/O P1[8] — General purpose digital input/output pin.

IENET_CRS — Ethernet carrier sense. (LPC1769/68/67/66/64 only).

P1[9]/

ENET_RXD0

91 B5 D3 [1] I/O P1[9] — General purpose digital input/output pin.

IENET_RXD0 — Ethernet receive data. (LPC1769/68/67/66/64

only).

P1[10]/

ENET_RXD1

90 A5 E3 [1] I/O P1[10] — General purpose digital input/output pin.

IENET_RXD1 — Ethernet receive data. (LPC1769/68/67/66/64

only).

P1[14]/

ENET_RX_ER

89 D6 E2 [1] I/O P1[14] — General purpose digital input/output pin.

IENET_RX_ER — Ethernet receive error. (LPC1769/68/67/66/64

only).

P1[15]/

ENET_REF_CLK

88 C6 E1 [1] I/O P1[15] — General purpose digital input/output pin.

IENET_REF_CLK — Ethernet reference clock.

(LPC1769/68/67/66/64 only).

P1[16]/

ENET_MDC

87 A6 F3 [1] I/O P1[16] — General purpose digital input/output pin.

OENET_MDC — Ethernet MIIM clock (LPC1769/68/67/66/64 only).

P1[17]/

ENET_MDIO

86 B6 F2 [1] I/O P1[17] — General purpose digital input/output pin.

I/O ENET_MDIO — Ethernet MIIM data input and output.

(LPC1769/68/67/66/64 only).

Table 5. Pin description …continued

Symbol Pin/ball Type Description

LQFP100

TFBGA100

WLCSP100

Product data sheet Rev. 9.10 — 8 September 2020 15 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

P1[18]/

USB_UP_LED/

PWM1[1]/

CAP1[0]

32 H4 D9 [1] I/O P1[18] — General purpose digital input/output pin.

OUSB_UP_LED — USB GoodLink LED indicator. It is LOW when the

device is configured (non-control endpoints enabled), or when the

host is enabled and has detected a device on the bus. It is HIGH

when the device is not configured, or when host is enabled and has

not detected a device on the bus, or during global suspend. It

transitions between LOW and HIGH (flashes) when the host is

enabled and detects activity on the bus. (LPC1769/68/66/65/64

only).

OPWM1[1] — Pulse Width Modulator 1, channel 1 output.

ICAP1[0] — Capture input for Timer 1, channel 0.

P1[19]/MCOA0/

USB_PPWR/

CAP1[1]

33 J4 C10 [1] I/O P1[19] — General purpose digital input/output pin.

OMCOA0 — Motor control PWM channel 0, output A.

OUSB_PPWR — Port Power enable signal for USB port.

(LPC1769/68/66/65 only).

ICAP1[1] — Capture input for Timer 1, channel 1.

P1[20]/MCI0/

PWM1[2]/SCK0

34 K4 E8 [1] I/O P1[20] — General purpose digital input/output pin.

IMCI0 — Motor control PWM channel 0, input. Also Quadrature

Encoder Interface PHA input.

OPWM1[2] — Pulse Width Modulator 1, channel 2 output.

I/O SCK0 — Serial clock for SSP0.

P1[21]/MCABORT/

PWM1[3]/

SSEL0

35 F5 E9 [1] I/O P1[21] — General purpose digital input/output pin.

OMCABORT — Motor control PWM, LOW-active fast abort.

OPWM1[3] — Pulse Width Modulator 1, channel 3 output.

I/O SSEL0 — Slave Select for SSP0.

P1[22]/MCOB0/

USB_PWRD/

MAT1[0]

36 J5 D10 [1] I/O P1[22] — General purpose digital input/output pin.

OMCOB0 — Motor control PWM channel 0, output B.

IUSB_PWRD — Power Status for USB port (host power switch,

LPC1769/68/66/65 only).

OMAT1[0] — Match output for Timer 1, channel 0.

P1[23]/MCI1/

PWM1[4]/MISO0

37 K5 E7 [1] I/O P1[23] — General purpose digital input/output pin.

IMCI1 — Motor control PWM channel 1, input. Also Quadrature

Encoder Interface PHB input.

OPWM1[4] — Pulse Width Modulator 1, channel 4 output.

I/O MISO0 — Master In Slave Out for SSP0.

P1[24]/MCI2/

PWM1[5]/MOSI0

38 H5 F8 [1] I/O P1[24] — General purpose digital input/output pin.

IMCI2 — Motor control PWM channel 2, input. Also Quadrature

Encoder Interface INDEX input.

OPWM1[5] — Pulse Width Modulator 1, channel 5 output.

I/O MOSI0 — Master Out Slave in for SSP0.

Table 5. Pin description …continued

Symbol Pin/ball Type Description

LQFP100

TFBGA100

WLCSP100

Product data sheet Rev. 9.10 — 8 September 2020 16 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

P1[25]/MCOA1/

MAT1[1]

39 G5 F9 [1] I/O P1[25] — General purpose digital input/output pin.

OMCOA1 — Motor control PWM channel 1, output A.

OMAT1[1] — Match output for Timer 1, channel 1.

P1[26]/MCOB1/

PWM1[6]/CAP0[0]

40 K6 E10 [1] I/O P1[26] — General purpose digital input/output pin.

OMCOB1 — Motor control PWM channel 1, output B.

OPWM1[6] — Pulse Width Modulator 1, channel 6 output.

ICAP0[0] — Capture input for Timer 0, channel 0.

P1[27]/CLKOUT

/USB_OVRCR/

CAP0[1]

43 K7 G9 [1] I/O P1[27] — General purpose digital input/output pin.

OCLKOUT — Clock output pin.

IUSB_OVRCR — USB port Over-Current status. (LPC1769/68/66/65

only).

ICAP0[1] — Capture input for Timer 0, channel 1.

P1[28]/MCOA2/

PCAP1[0]/

MAT0[0]

44 J7 G10 [1] I/O P1[28] — General purpose digital input/output pin.

OMCOA2 — Motor control PWM channel 2, output A.

IPCAP1[0] — Capture input for PWM1, channel 0.

OMAT0[0] — Match output for Timer 0, channel 0.

P1[29]/MCOB2/

PCAP1[1]/

MAT0[1]

45 G6 G8 [1] I/O P1[29] — General purpose digital input/output pin.

OMCOB2 — Motor control PWM channel 2, output B.

IPCAP1[1] — Capture input for PWM1, channel 1.

OMAT0[1] — Match output for Timer 0, channel 1.

P1[30]/VBUS/

AD0[4]

21 H1 B8 [2] I/O P1[30] — General purpose digital input/output pin.

IVBUS — Monitors the presence of USB bus power.

(LPC1769/68/66/65/64 only).

Note: This signal must be HIGH for USB reset to occur.

IAD0[4] — A/D converter 0, input 4.

P1[31]/SCK1/

AD0[5]

20 F4 C7 [2] I/O P1[31] — General purpose digital input/output pin.

I/O SCK1 — Serial Clock for SSP1.

IAD0[5] — A/D converter 0, input 5.

P2[0] to P2[31] I/O Port 2: Port 2 is a 32-bit I/O port with individual direction controls for

each bit. The operation of port 2 pins depends upon the pin function

selected via the pin connect block. Pins 14 through 31 of this port

are not available.

P2[0]/PWM1[1]/

TXD1

75 B9 K1 [1] I/O P2[0] — General purpose digital input/output pin.

OPWM1[1] — Pulse Width Modulator 1, channel 1 output.

OTXD1 — Transmitter output for UART1.

P2[1]/PWM1[2]/

RXD1

74 B10 J2 [1] I/O P2[1] — General purpose digital input/output pin.

OPWM1[2] — Pulse Width Modulator 1, channel 2 output.

IRXD1 — Receiver input for UART1.

Table 5. Pin description …continued

Symbol Pin/ball Type Description

LQFP100

TFBGA100

WLCSP100

Product data sheet Rev. 9.10 — 8 September 2020 17 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

P2[2]/PWM1[3]/

CTS1/

TRACEDATA[3]

73 D8 K2 [1] I/O P2[2] — General purpose digital input/output pin.

OPWM1[3] — Pulse Width Modulator 1, channel 3 output.

ICTS1 — Clear to Send input for UART1.

OTRACEDATA[3] — Trace data, bit 3.

P2[3]/PWM1[4]/

DCD1/

TRACEDATA[2]

70 E7 K3 [1] I/O P2[3] — General purpose digital input/output pin.

OPWM1[4] — Pulse Width Modulator 1, channel 4 output.

IDCD1 — Data Carrier Detect input for UART1.

OTRACEDATA[2] — Trace data, bit 2.

P2[4]/PWM1[5]/

DSR1/

TRACEDATA[1]

69 D9 J3 [1] I/O P2[4] — General purpose digital input/output pin.

OPWM1[5] — Pulse Width Modulator 1, channel 5 output.

IDSR1 — Data Set Ready input for UART1.

OTRACEDATA[1] — Trace data, bit 1.

P2[5]/PWM1[6]/

DTR1/

TRACEDATA[0]

68 D10 H4 [1] I/O P2[5] — General purpose digital input/output pin.

OPWM1[6] — Pulse Width Modulator 1, channel 6 output.

ODTR1 — Data Terminal Ready output for UART1. Can also be

configured to be an RS-485/EIA-485 output enable signal.

OTRACEDATA[0] — Trace data, bit 0.

P2[6]/PCAP1[0]/

RI1/TRACECLK

67 E8 K4 [1] I/O P2[6] — General purpose digital input/output pin.

IPCAP1[0] — Capture input for PWM1, channel 0.

IRI1 — Ring Indicator input for UART1.

OTRACECLK — Trace Clock.

P2[7]/RD2/

RTS1

66 E9 J4 [1] I/O P2[7] — General purpose digital input/output pin.

IRD2 — CAN2 receiver input. (LPC1769/68/66/65/64 only).

ORTS1 — Request to Send output for UART1. Can also be

configured to be an RS-485/EIA-485 output enable signal.

P2[8]/TD2/

TXD2

65 E10 H5 [1] I/O P2[8] — General purpose digital input/output pin.

OTD2 — CAN2 transmitter output. (LPC1769/68/66/65/64 only).

OTXD2 — Transmitter output for UART2.

P2[9]/

USB_CONNECT/

RXD2

64 F7 K5 [1] I/O P2[9] — General purpose digital input/output pin.

OUSB_CONNECT — Signal used to switch an external 1.5 k

resistor under software control. Used with the SoftConnect USB

feature. (LPC1769/68/66/65/64 only).

IRXD2 — Receiver input for UART2.

P2[10]/EINT0/NMI 53 J10 K9 [6] I/O P2[10] — General purpose digital input/output pin. A LOW level on

this pin during reset starts the ISP command handler.

IEINT0 — External interrupt 0 input.

INMI — Non-maskable interrupt input.

Table 5. Pin description …continued

Symbol Pin/ball Type Description

LQFP100

TFBGA100

WLCSP100

Product data sheet Rev. 9.10 — 8 September 2020 18 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

P2[11]/EINT1/

I2STX_CLK

52 H8 J8 [6] I/O P2[11] — General purpose digital input/output pin.

IEINT1 — External interrupt 1 input.

I/O I2STX_CLK — Transmit Clock. It is driven by the master and

received by the slave. Corresponds to the signal SCK in the I2S-bus

specification. (LPC1769/68/67/66/65/63 only).

P2[12]/EINT2/

I2STX_WS

51 K10 K10 [6] I/O P2[12] — General purpose digital input/output pin.

IEINT2 — External interrupt 2 input.

I/O I2STX_WS — Transmit Word Select. It is driven by the master and

received by the slave. Corresponds to the signal WS in the I2S-bus

specification. (LPC1769/68/67/66/65/63 only).

P2[13]/EINT3/

I2STX_SDA

50 J9 J9 [6] I/O P2[13] — General purpose digital input/output pin.

IEINT3 — External interrupt 3 input.

I/O I2STX_SDA — Transmit data. It is driven by the transmitter and

read by the receiver. Corresponds to the signal SD in the I2S-bus

specification. (LPC1769/68/67/66/65/63 only).

P3[0] to P3[31] I/O Port 3: Port 3 is a 32-bit I/O port with individual direction controls for

each bit. The operation of port 3 pins depends upon the pin function

selected via the pin connect block. Pins 0 through 24, and 27

through 31 of this port are not available.

P3[25]/MAT0[0]/

PWM1[2]

27 H3 D8 [1] I/O P3[25] — General purpose digital input/output pin.

OMAT0[0] — Match output for Timer 0, channel 0.

OPWM1[2] — Pulse Width Modulator 1, output 2.

P3[26]/STCLK/

MAT0[1]/PWM1[3]

26 K1 A10 [1] I/O P3[26] — General purpose digital input/output pin.

ISTCLK — System tick timer clock input. The maximum STCLK

frequency is 1/4 of the Arm processor clock frequency CCLK.

OMAT0[1] — Match output for Timer 0, channel 1.

OPWM1[3] — Pulse Width Modulator 1, output 3.

P4[0] to P4[31] I/O Port 4: Port 4 is a 32-bit I/O port with individual direction controls for

each bit. The operation of port 4 pins depends upon the pin function

selected via the pin connect block. Pins 0 through 27, 30, and 31 of

this port are not available.

P4[28]/RX_MCLK/

MAT2[0]/TXD3

82 C7 G1 [1] I/O P4[28] — General purpose digital input/output pin.

ORX_MCLK — I2S receive master clock. (LPC1769/68/67/66/65

only).

OMAT2[0] — Match output for Timer 2, channel 0.

OTXD3 — Transmitter output for UART3.

P4[29]/TX_MCLK/

MAT2[1]/RXD3

85 E6 F1 [1] I/O P4[29] — General purpose digital input/output pin.

OTX_MCLK — I2S transmit master clock. (LPC1769/68/67/66/65

only).

OMAT2[1] — Match output for Timer 2, channel 1.

IRXD3 — Receiver input for UART3.

Table 5. Pin description …continued

Symbol Pin/ball Type Description

LQFP100

TFBGA100

WLCSP100

Product data sheet Rev. 9.10 — 8 September 2020 19 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

TDO/SWO 1 A1 A1 [7] OTDO — Test Data out for JTAG interface.

OSWO — Serial wire trace output.

TDI 2 C3 C4 [1][8] ITDI — Test Data in for JTAG interface.

TMS/SWDIO 3 B1 B3 [1][8] ITMS — Test Mode Select for JTAG interface.

I/O SWDIO — Serial wire debug data input/output.

TRST 4 C2 A2 [1][8] ITRST — Test Reset for JTAG interface.

TCK/SWDCLK 5 C1 D4 [7] ITCK — Test Clock for JTAG interface.

ISWDCLK — Serial wire clock.

RTCK 100 B2 B2 [7] ORTCK — JTAG interface control signal.

RSTOUT 14 - - - O RSTOUT — This is a 3.3 V pin. LOW on this pin indicates the

microcontroller being in Reset state.

RESET 17 F3 C6 [9] IExternal reset input: A LOW-going pulse as short as 50 ns on this

pin resets the device, causing I/O ports and peripherals to take on

their default states, and processor execution to begin at address 0.

TTL with hysteresis, 5 V tolerant.

XTAL1 22 H2 D7 [10][11] I Input to the oscillator circuit and internal clock generator circuits.

XTAL2 23 G3 A9 [10][11] O Output from the oscillator amplifier.

RTCX1 16 F2 A7 [10][11] I Input to the RTC oscillator circuit.

RTCX2 18 G1 B7 [10] O Output from the RTC oscillator circuit.

VSS 31,

41,

55,

72,

83,

B3,

B7,

C9,

G7,

J6,

E5,

F5,

F6,

G5,

G6,

[10] Iground: 0 V reference.

VSSA 11 E1 B5 [10] Ianalog ground: 0 V reference. This should nominally be the same

voltage as VSS, but should be isolated to minimize noise and error.

VDD(3V3) 28,

54,

71,

K2,

H9,

C10

, A3

E4,

E6,

F7,

[10] I3.3 V supply voltage: This is the power supply voltage for the I/O

ports.

VDD(REG)(3V3) 42,

H6,

F4,

F10

[10] I3.3 V voltage regulator supply voltage: This is the supply voltage

for the on-chip voltage regulator only.

VDDA 10 E2 A4 [10] Ianalog 3.3 V pad supply voltage: This should be nominally the

same voltage as VDD(3V3) but should be isolated to minimize noise

and error. This voltage is used to power the ADC and DAC. This pin

should be tied to 3.3 V if the ADC and DAC are not used.

VREFP 12 E3 A5 [10] IADC positive reference voltage: This should be nominally the

same voltage as VDDA but should be isolated to minimize noise and

error. Level on this pin is used as a reference for ADC and DAC.

This pin should be tied to 3.3 V if the ADC and DAC are not used.

Table 5. Pin description …continued

Symbol Pin/ball Type Description

LQFP100

TFBGA100

WLCSP100

Product data sheet Rev. 9.10 — 8 September 2020 20 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

[1] 5 V tolerant pad providing digital I/O functions with TTL levels and hysteresis. This pin is pulled up to a voltage level of 2.3 V to 2.6 V.

[2] 5 V tolerant pad providing digital I/O functions (with TTL levels and hysteresis) and analog input. When configured as a ADC input,

digital section of the pad is disabled and the pin is not 5 V tolerant. This pin is pulled up to a voltage level of 2.3 V to 2.6 V.

[3] 5 V tolerant pad providing digital I/O with TTL levels and hysteresis and analog output function. When configured as the DAC output,

digital section of the pad is disabled. This pin is pulled up to a voltage level of 2.3 V to 2.6 V.

[4] Open-drain 5 V tolerant digital I/O pad, compatible with I2C-bus 400 kHz specification. This pad requires an external pull-up to provide

output functionality. When power is switched off, this pin connected to the I2C-bus is floating and does not disturb the I2C lines.

Open-drain configuration applies to all functions on this pin.

[5] Pad provides digital I/O and USB functions. It is designed in accordance with the USB specification, revision 2.0 (Full-speed and

Low-speed mode only). This pad is not 5 V tolerant.

[6] 5 V tolerant pad with 10 ns glitch filter providing digital I/O functions with TTL levels and hysteresis. This pin is pulled up to a voltage

level of 2.3 V to 2.6 V.

[7] 5 V tolerant pad with TTL levels and hysteresis. Internal pull-up and pull-down resistors disabled.

[8] 5 V tolerant pad with TTL levels and hysteresis and internal pull-up resistor.

[9] 5 V tolerant pad with 20 ns glitch filter providing digital I/O function with TTL levels and hysteresis.

[10] Pad provides special analog functionality. A 32 kHz crystal oscillator must be used with the RTC.

[11] When the system oscillator is not used, connect XTAL1 and XTAL2 as follows: XTAL1 can be left floating or can be grounded

(grounding is preferred to reduce susceptibility to noise). XTAL2 should be left floating.

[12] When the RTC is not used, connect VBAT to VDD(REG)(3V3) and leave RTCX1 floating.

VREFN 15 F1 A6 I ADC negative reference voltage: This should be nominally the

same voltage as VSS but should be isolated to minimize noise and

error. Level on this pin is used as a reference for ADC and DAC.

VBAT 19 G2 A8 [10][12] IRTC pin power supply: 3.3 V on this pin supplies the power to the

RTC peripheral.

n.c. 13 D4,

B6,

- not connected.

Table 5. Pin description …continued

Symbol Pin/ball Type Description

LQFP100

TFBGA100

WLCSP100

Product data sheet Rev. 9.10 — 8 September 2020 21 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

8. Functional description

8.1 Architectural overview

Remark: In the following, the notation LPC17xx refers to all parts:

LPC1769/68/67/66/65/64/63.

The Arm Cortex-M3 includes three AHB-Lite buses: the system bus, the I-code bus, and

the D-code bus (see Figure 1). The I-code and D-code core buses are faster than the

system bus and are used similarly to TCM interfaces: one bus dedicated for instruction

fetch (I-code) and one bus for data access (D-code). The use of two core buses allows for

simultaneous operations if concurrent operations target different devices.

The LPC17xx use a multi-layer AHB matrix to connect the Arm Cortex-M3 buses and

other bus masters to peripherals in a flexible manner that optimizes performance by

allowing peripherals that are on different slaves ports of the matrix to be accessed

simultaneously by different bus masters.

8.2 Arm Cortex-M3 processor

The Arm Cortex-M3 is a general purpose, 32-bit microprocessor, which offers high

performance and very low power consumption. The Arm Cortex-M3 offers many new

features, including a Thumb-2 instruction set, low interrupt latency, hardware divide,

interruptible/continuable multiple load and store instructions, automatic state save and

restore for interrupts, tightly integrated interrupt controller with wake-up interrupt

controller, and multiple core buses capable of simultaneous accesses.

Pipeline techniques are employed so that all parts of the processing and memory systems

can operate continuously. Typically, while one instruction is being executed, its successor

is being decoded, and a third instruction is being fetched from memory.

The Arm Cortex-M3 processor is described in detail in the Cortex-M3 Technical

Reference Manual that can be found on official Arm website.

8.3 On-chip flash program memory

The LPC17xx contain up to 512 kB of on-chip flash memory. A new two-port flash

accelerator maximizes performance for use with the two fast AHB-Lite buses.

8.4 On-chip SRAM

The LPC17xx contain a total of 64 kB on-chip static RAM memory. This includes the main

32 kB SRAM, accessible by the CPU and DMA controller on a higher-speed bus, and two

additional 16 kB each SRAM blocks situated on a separate slave port on the AHB

multilayer matrix.

This architecture allows CPU and DMA accesses to be spread over three separate RAMs

that can be accessed simultaneously.

8.5 Memory Protection Unit (MPU)

The LPC17xx have a Memory Protection Unit (MPU) which can be used to improve the

reliability of an embedded system by protecting critical data within the user application.

Product data sheet Rev. 9.10 — 8 September 2020 22 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

The MPU allows separating processing tasks by disallowing access to each other's data,

disabling access to memory regions, allowing memory regions to be defined as read-only

and detecting unexpected memory accesses that could potentially break the system.

The MPU separates the memory into distinct regions and implements protection by

preventing disallowed accesses. The MPU supports up to 8 regions each of which can be

divided into 8 subregions. Accesses to memory locations that are not defined in the MPU

regions, or not permitted by the region setting, will cause the Memory Management Fault

exception to take place.

8.6 Memory map

The LPC17xx incorporates several distinct memory regions, shown in the following

figures. Figure 5 shows the overall map of the entire address space from the user

program viewpoint following reset. The interrupt vector area supports address remapping.

The AHB peripheral area is 2 MB in size and is divided to allow for up to 128 peripherals.

The APB peripheral area is 1 MB in size and is divided to allow for up to 64 peripherals.

Each peripheral of either type is allocated 16 kB of space. This allows simplifying the

address decoding for each peripheral.

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 9.10 — 8 September 2020 23 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

(1) Not available on all parts. See Table 2.

Fig 5. LPC17xx memory map

0x5000 0000

0x5000 4000

0x5000 8000

0x5000 C000

0x5020 0000

0x5001 0000

AHB peripherals

Ethernet controller(1)

USB controller(1)

reserved

127- 4 reserved

GPDMA controller

APB0 peripherals

0x4000 4000

0x4000 8000

0x4000 C000

0x4001 0000

0x4001 8000

0x4002 0000

0x4002 8000

0x4002 C000

0x4003 4000

0x4003 0000

0x4003 8000

0x4003 C000

0x4004 0000

0x4004 4000

0x4004 8000

0x4004 C000

0x4005 C000

0x4006 0000

0x4008 0000

0x4002 4000

0x4001 C000

0x4001 4000

timer 0

timer 1

UART0

UART1

reserved

I2C0

SPI

RTC + backup registers

GPIO interrupts

pin connect

SSP1

ADC

CAN AF RAM(1)

CAN AF registers(1)

CAN common(1)

CAN1(1)

CAN2(1)

22 - 19 reserved

I2C1

31 - 24 reserved

reserved

32 kB local SRAM (LPC1769/8/7/6/5/3)

16 kB local SRAM (LPC1764)

reserved

private peripheral bus

0.5 GB

4 GB

1 GB

0x0004 0000

0x0002 0000

0x0008 0000

0x1000 4000

0x1000 0000

0x1000 8000

0x1FFF 0000

0x1FFF 2000

0x2008 0000

0x2007 C000

0x2008 4000

0x2200 0000

0x200A 0000

0x2009 C000

0x2400 0000

0x4000 0000

0x4008 0000

0x4010 0000

0x4200 0000

0x4400 0000

0x5000 0000

0x5020 0000

0xE000 0000

0xE010 0000

0xFFFF FFFF

reserved

GPIO

reserved

APB0 peripherals

AHB peripherals

APB1 peripherals

AHB SRAM bit-band alias addressing

peripheral bit-band alias addressing

16 kB AHB SRAM1 (LPC1769/8/7/6/5)

16 kB AHB SRAM0

256 kB on-chip flash (LPC1766/65/63)

512 kB on-chip flash (LPC1769/8/7)

PWM1

8 kB boot ROM

0x0000 0000

0x0000 0400

active interru

t vectors

+ 256 words

I-code/D-code

memory space

APB1 peripherals

0x4008 0000

0x4008 8000

x4008 C000

0x4009 0000

0x4009 4000

0x4009 8000

x4009 C000

0x400A 0000

0x400A 4000

0x400A 8000

x400A C000

x400B 0000

x400B 4000

x400B 8000

x400B C000

x400C 0000

x400F C000

0x4010 0000

SSP0

DAC(1)

timer 2

timer 3

UART2

UART3

reserved

I2S(1)

I2C2

1 - 0 reserved

reserved

repetitive interrupt timer

reserved

motor control PWM

30 - 16 reserved

system control31

QEI

LPC1769/68/67/66/65/64/63

Product data sheet Rev. 9.10 — 8 September 2020 24 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

8.7 Nested Vectored Interrupt Controller (NVIC)

The NVIC is an integral part of the Cortex-M3. The tight coupling to the CPU allows for low

interrupt latency and efficient processing of late arriving interrupts.

8.7.1 Features

•Controls system exceptions and peripheral interrupts

•In the LPC17xx, the NVIC supports 33 vectored interrupts

•32 programmable interrupt priority levels, with hardware priority level masking

•Relocatable vector table

•Non-Maskable Interrupt (NMI)

•Software interrupt generation

8.7.2 Interrupt sources

Each peripheral device has one interrupt line connected to the NVIC but may have several

interrupt flags. Individual interrupt flags may also represent more than one interrupt

source.

Any pin on Port 0 and Port 2 (total of 42 pins) regardless of the selected function, can be

programmed to generate an interrupt on a rising edge, a falling edge, or both.

8.8 Pin connect block

The pin connect block allows selected pins of the microcontroller to have more than one

function. Configuration registers control the multiplexers to allow connection between the

pin and the on-chip peripherals.

Peripherals should be connected to the appropriate pins prior to being activated and prior

to any related interrupt(s) being enabled. Activity of any enabled peripheral function that is

not mapped to a related pin should be considered undefined.

Most pins can also be configured as open-drain outputs or to have a pull-up, pull-down, or

no resistor enabled.

8.9 General purpose DMA controller

The GPDMA is an AMBA AHB compliant peripheral allowing selected peripherals to have

DMA support.

The GPDMA enables peripheral-to-memory, memory-to-peripheral,

peripheral-to-peripheral, and memory-to-memory transactions. The source and

destination areas can each be either a memory region or a peripheral, and can be

accessed through the AHB master. The GPDMA controller allows data transfers between

the USB and Ethernet controllers and the various on-chip SRAM areas. The supported

APB peripherals are SSP0/1, all UARTs, the I2S-bus interface, the ADC, and the DAC.

Two match signals for each timer can be used to trigger DMA transfers.

Remark: The Ethernet controller is available on parts LPC1769/68/67/66/64. The USB

controller is available on parts LPC1769/68/66/65/64. The I2S-bus interface is available on

parts LPC1769/68/67/66/65. The DAC is available on parts LPC1769/68/67/66/65/63.

Product data sheet Rev. 9.10 — 8 September 2020 25 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

8.9.1 Features

•Eight DMA channels. Each channel can support an unidirectional transfer.

•16 DMA request lines.

•Single DMA and burst DMA request signals. Each peripheral connected to the DMA

Controller can assert either a burst DMA request or a single DMA request. The DMA

burst size is set by programming the DMA Controller.

•Memory-to-memory, memory-to-peripheral, peripheral-to-memory, and

peripheral-to-peripheral transfers are supported.

•Scatter or gather DMA is supported through the use of linked lists. This means that

the source and destination areas do not have to occupy contiguous areas of memory.

•Hardware DMA channel priority.

•AHB slave DMA programming interface. The DMA Controller is programmed by

writing to the DMA control registers over the AHB slave interface.

•One AHB bus master for transferring data. The interface transfers data when a DMA

request goes active.

•32-bit AHB master bus width.

•Incrementing or non-incrementing addressing for source and destination.

•Programmable DMA burst size. The DMA burst size can be programmed to more

efficiently transfer data.

•Internal four-word FIFO per channel.

•Supports 8, 16, and 32-bit wide transactions.

•Big-endian and little-endian support. The DMA Controller defaults to little-endian

mode on reset.

•An interrupt to the processor can be generated on a DMA completion or when a DMA

error has occurred.

•Raw interrupt status. The DMA error and DMA count raw interrupt status can be read

prior to masking.

8.10 Fast general purpose parallel I/O

Device pins that are not connected to a specific peripheral function are controlled by the

GPIO registers. Pins may be dynamically configured as inputs or outputs. Separate

registers allow setting or clearing any number of outputs simultaneously. The value of the

output register may be read back as well as the current state of the port pins.

LPC17xx use accelerated GPIO functions:

•GPIO registers are accessed through the AHB multilayer bus so that the fastest

possible I/O timing can be achieved.

•Mask registers allow treating sets of port bits as a group, leaving other bits

unchanged.

•All GPIO registers are byte and half-word addressable.

•Entire port value can be written in one instruction.

•Support for Cortex-M3 bit banding.

•Support for use with the GPDMA controller.

Product data sheet Rev. 9.10 — 8 September 2020 26 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Additionally, any pin on Port 0 and Port 2 (total of 42 pins) providing a digital function can

be programmed to generate an interrupt on a rising edge, a falling edge, or both. The

edge detection is asynchronous, so it may operate when clocks are not present such as

during Power-down mode. Each enabled interrupt can be used to wake up the chip from

Power-down mode.

8.10.1 Features

•Bit level set and clear registers allow a single instruction to set or clear any number of

bits in one port.

•Direction control of individual bits.

•All I/O default to inputs after reset.

•Pull-up/pull-down resistor configuration and open-drain configuration can be

programmed through the pin connect block for each GPIO pin.

8.11 Ethernet

Remark: The Ethernet controller is available on parts LPC1769/68/67/66/64. The

Ethernet block supports bus clock rates of up to 100 MHz (LPC1768/67/66/64) or 120

MHz (LPC1769). See Table 2.

The Ethernet block contains a full featured 10 Mbit/s or 100 Mbit/s Ethernet MAC

designed to provide optimized performance through the use of DMA hardware

acceleration. Features include a generous suite of control registers, half or full duplex

operation, flow control, control frames, hardware acceleration for transmit retry, receive

packet filtering and wake-up on LAN activity. Automatic frame transmission and reception

with scatter-gather DMA off-loads many operations from the CPU.

The Ethernet block and the CPU share the Arm Cortex-M3 D-code and system bus

through the AHB-multilayer matrix to access the various on-chip SRAM blocks for

Ethernet data, control, and status information.

The Ethernet block interfaces between an off-chip Ethernet PHY using the Reduced MII

(RMII) protocol and the on-chip Media Independent Interface Management (MIIM) serial

bus.

8.11.1 Features

•Ethernet standards support:

–Supports 10 Mbit/s or 100 Mbit/s PHY devices including 10 Base-T, 100 Base-TX,

100 Base-FX, and 100 Base-T4.

–Fully compliant with IEEE standard 802.3.

–Fully compliant with 802.3x full duplex flow control and half duplex back pressure.

–Flexible transmit and receive frame options.

–Virtual Local Area Network (VLAN) frame support.

•Memory management:

–Independent transmit and receive buffers memory mapped to shared SRAM.

–DMA managers with scatter/gather DMA and arrays of frame descriptors.

–Memory traffic optimized by buffering and pre-fetching.

Product data sheet Rev. 9.10 — 8 September 2020 27 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

•Enhanced Ethernet features:

–Receive filtering.

–Multicast and broadcast frame support for both transmit and receive.

–Optional automatic Frame Check Sequence (FCS) insertion with Cyclic

Redundancy Check (CRC) for transmit.

–Selectable automatic transmit frame padding.

–Over-length frame support for both transmit and receive allows any length frames.

–Promiscuous receive mode.

–Automatic collision back-off and frame retransmission.

–Includes power management by clock switching.

–Wake-on-LAN power management support allows system wake-up: using the

receive filters or a magic frame detection filter.

•Physical interface:

–Attachment of external PHY chip through standard RMII interface.

–PHY register access is available via the MIIM interface.

8.12 USB interface

Remark: The USB controller is available as device/Host/OTG controller on parts

LPC1769/68/66/65 and as device-only controller on part LPC1764.

The Universal Serial Bus (USB) is a 4-wire bus that supports communication between a

host and one or more (up to 127) peripherals. The host controller allocates the USB

bandwidth to attached devices through a token-based protocol. The bus supports hot

plugging and dynamic configuration of the devices. All transactions are initiated by the

host controller.

The USB interface includes a device, Host, and OTG controller with on-chip PHY for

device and Host functions. The OTG switching protocol is supported through the use of an

external controller. Details on typical USB interfacing solutions can be found in

Section 15.1.

8.12.1 USB device controller

The device controller enables 12 Mbit/s data exchange with a USB Host controller. It

consists of a register interface, serial interface engine, endpoint buffer memory, and a

DMA controller. The serial interface engine decodes the USB data stream and writes data

to the appropriate endpoint buffer. The status of a completed USB transfer or error

condition is indicated via status registers. An interrupt is also generated if enabled. When

enabled, the DMA controller transfers data between the endpoint buffer and the on-chip

SRAM.

8.12.1.1 Features

•Fully compliant with USB 2.0 specification (full speed).

•Supports 32 physical (16 logical) endpoints with a 4 kB endpoint buffer RAM.

•Supports Control, Bulk, Interrupt and Isochronous endpoints.

•Scalable realization of endpoints at run time.

Product data sheet Rev. 9.10 — 8 September 2020 28 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

•Endpoint Maximum packet size selection (up to USB maximum specification) by

software at run time.

•Supports SoftConnect and GoodLink features.

•While USB is in the Suspend mode, the part can enter one of the reduced power

modes and wake up on USB activity.

•Supports DMA transfers with all on-chip SRAM blocks on all non-control endpoints.

•Allows dynamic switching between CPU-controlled slave and DMA modes.

•Double buffer implementation for Bulk and Isochronous endpoints.

8.12.2 USB host controller

The host controller enables full- and low-speed data exchange with USB devices attached

to the bus. It consists of a register interface, a serial interface engine, and a DMA

controller. The register interface complies with the OHCI specification.

8.12.2.1 Features

•OHCI compliant.

•One downstream port.

•Supports port power switching.

8.12.3 USB OTG controller

USB OTG is a supplement to the USB 2.0 specification that augments the capability of

existing mobile devices and USB peripherals by adding host functionality for connection to

USB peripherals.

The OTG Controller integrates the host controller, device controller, and a master-only

I2C-bus interface to implement OTG dual-role device functionality. The dedicated I2C-bus

interface controls an external OTG transceiver.

8.12.3.1 Features

•Fully compliant with On-The-Go supplement to the USB 2.0 Specification, Revision

1.0a.

•Hardware support for Host Negotiation Protocol (HNP).

•Includes a programmable timer required for HNP and Session Request Protocol

(SRP).

•Supports any OTG transceiver compliant with the OTG Transceiver Specification

(CEA-2011), Rev. 1.0.

8.13 CAN controller and acceptance filters

Remark: The CAN controllers are available on parts LPC1769/68/66/65/64. See Table 2.

The Controller Area Network (CAN) is a serial communications protocol which efficiently

supports distributed real-time control with a very high level of security. Its domain of

application ranges from high-speed networks to low cost multiplex wiring.

The CAN block is intended to support multiple CAN buses simultaneously, allowing the

device to be used as a gateway, switch, or router among a number of CAN buses in

industrial or automotive applications.

Product data sheet Rev. 9.10 — 8 September 2020 29 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

8.13.1 Features

•Two CAN controllers and buses.

•Data rates to 1 Mbit/s on each bus.

•32-bit register and RAM access.

•Compatible with CAN specification 2.0B, ISO 11898-1.

•Global Acceptance Filter recognizes standard (11-bit) and extended-frame (29-bit)

receive identifiers for all CAN buses.

•Acceptance Filter can provide FullCAN-style automatic reception for selected

Standard Identifiers.

•FullCAN messages can generate interrupts.

8.14 12-bit ADC

The LPC17xx contain a single 12-bit successive approximation ADC with eight channels

and DMA support.

8.14.1 Features

•12-bit successive approximation ADC.

•Input multiplexing among 8 pins.

•Power-down mode.

•Measurement range VREFN to VREFP.

•12-bit conversion rate: 200 kHz.

•Individual channels can be selected for conversion.

•Burst conversion mode for single or multiple inputs.

•Optional conversion on transition of input pin or Timer Match signal.

•Individual result registers for each ADC channel to reduce interrupt overhead.

•DMA support.

8.15 10-bit DAC

The DAC allows to generate a variable analog output. The maximum output value of the

DAC is VREFP.

Remark: The DAC is available on parts LPC1769/68/67/66/65/63. See Table 2.

8.15.1 Features

•10-bit DAC

•Resistor string architecture

•Buffered output

•Power-down mode

•Selectable output drive

•Dedicated conversion timer

•DMA support

Product data sheet Rev. 9.10 — 8 September 2020 30 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

8.16 UARTs

The LPC17xx each contain four UARTs. In addition to standard transmit and receive data

lines, UART1 also provides a full modem control handshake interface and support for

RS-485/9-bit mode allowing both software address detection and automatic address

detection using 9-bit mode.

The UARTs include a fractional baud rate generator. Standard baud rates such as

115 200 Bd can be achieved with any crystal frequency above 2 MHz.

8.16.1 Features

•Maximum UART data bit rate of 6.25 Mbit/s.

•16 B Receive and Transmit FIFOs.

•Register locations conform to 16C550 industry standard.

•Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.

•Built-in fractional baud rate generator covering wide range of baud rates without a

need for external crystals of particular values.

•Auto baud capabilities and FIFO control mechanism that enables software flow

control implementation.

•UART1 equipped with standard modem interface signals. This module also provides

full support for hardware flow control (auto-CTS/RTS).

•Support for RS-485/9-bit/EIA-485 mode (UART1).

•UART3 includes an IrDA mode to support infrared communication.

•All UARTs have DMA support.

8.17 SPI serial I/O controller

The LPC17xx contain one SPI controller. SPI is a full duplex serial interface designed to

handle multiple masters and slaves connected to a given bus. Only a single master and a

single slave can communicate on the interface during a given data transfer. During a data

transfer the master always sends 8 bits to 16 bits of data to the slave, and the slave

always sends 8 bits to 16 bits of data to the master.

8.17.1 Features

•Maximum SPI data bit rate of 12.5 Mbit/s

•Compliant with SPI specification

•Synchronous, serial, full duplex communication

•Combined SPI master and slave

•Maximum data bit rate of one eighth of the input clock rate

•8 bits to 16 bits per transfer

8.18 SSP serial I/O controller

The LPC17xx contain two SSP controllers. The SSP controller is capable of operation on

a SPI, 4-wire SSI, or Microwire bus. It can interact with multiple masters and slaves on the

bus. Only a single master and a single slave can communicate on the bus during a given

Product data sheet Rev. 9.10 — 8 September 2020 31 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

data transfer. The SSP supports full duplex transfers, with frames of 4 bits to 16 bits of

data flowing from the master to the slave and from the slave to the master. In practice,

often only one of these data flows carries meaningful data.

8.18.1 Features

•Maximum SSP speed of 33 Mbit/s (master) or 8 Mbit/s (slave)

•Compatible with Motorola SPI, 4-wire Texas Instruments SSI, and National

Semiconductor Microwire buses

•Synchronous serial communication

•Master or slave operation

•8-frame FIFOs for both transmit and receive

•4-bit to 16-bit frame

•DMA transfers supported by GPDMA

8.19 I2C-bus serial I/O controllers

The LPC17xx each contain three I2C-bus controllers.

The I2C-bus is bidirectional for inter-IC control using only two wires: a Serial Clock line

(SCL) and a Serial DAta line (SDA). Each device is recognized by a unique address and

can operate as either a receiver-only device (e.g., an LCD driver) or a transmitter with the

capability to both receive and send information (such as memory). Transmitters and/or

receivers can operate in either master or slave mode, depending on whether the chip has

to initiate a data transfer or is only addressed. The I2C is a multi-master bus and can be

controlled by more than one bus master connected to it.

8.19.1 Features

•I2C0 is a standard I2C compliant bus interface with open-drain pins. I2C0 also

supports Fast mode plus with bit rates up to 1 Mbit/s.

•I2C1 and I2C2 use standard I/O pins with bit rates of up to 400 kbit/s (Fast I2C-bus).

•Easy to configure as master, slave, or master/slave.

•Programmable clocks allow versatile rate control.

•Bidirectional data transfer between masters and slaves.

•Multi-master bus (no central master).

•Arbitration between simultaneously transmitting masters without corruption of serial

data on the bus.

•Serial clock synchronization allows devices with different bit rates to communicate via

one serial bus.

•Serial clock synchronization can be used as a handshake mechanism to suspend and

resume serial transfer.

•The I2C-bus can be used for test and diagnostic purposes.

•All I2C-bus controllers support multiple address recognition and a bus monitor mode.

Product data sheet Rev. 9.10 — 8 September 2020 32 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

8.20 I2S-bus serial I/O controllers

Remark: The I2S-bus interface is available on parts LPC1769/68/67/66/65/63. See

Table 2.

The I2S-bus provides a standard communication interface for digital audio applications.

The I2S-bus specification defines a 3-wire serial bus using one data line, one clock line,

and one word select signal. The basic I2S-bus connection has one master, which is

always the master, and one slave. The I2S-bus interface provides a separate transmit and

receive channel, each of which can operate as either a master or a slave.

8.20.1 Features

•The interface has separate input/output channels each of which can operate in master

or slave mode.

•Capable of handling 8-bit, 16-bit, and 32-bit word sizes.

•Mono and stereo audio data supported.

•The sampling frequency can range from 16 kHz to 96 kHz (16, 22.05, 32, 44.1, 48,

96) kHz.

•Support for an audio master clock.

•Configurable word select period in master mode (separately for I2S-bus input and

output).

•Two 8-word FIFO data buffers are provided, one for transmit and one for receive.

•Generates interrupt requests when buffer levels cross a programmable boundary.

•Two DMA requests, controlled by programmable buffer levels. These are connected

to the GPDMA block.

•Controls include reset, stop and mute options separately for I2S-bus input and I2S-bus

output.

8.21 General purpose 32-bit timers/external event counters

The LPC17xx include four 32-bit timer/counters. The timer/counter is designed to count

cycles of the system derived clock or an externally-supplied clock. It can optionally

generate interrupts, generate timed DMA requests, or perform other actions at specified

timer values, based on four match registers. Each timer/counter also includes two capture

inputs to trap the timer value when an input signal transitions, optionally generating an

interrupt.

8.21.1 Features

•A 32-bit timer/counter with a programmable 32-bit prescaler.

•Counter or timer operation.

•Two 32-bit capture channels per timer, that can take a snapshot of the timer value

when an input signal transitions. A capture event may also generate an interrupt.

•Four 32-bit match registers that allow:

–Continuous operation with optional interrupt generation on match.

–Stop timer on match with optional interrupt generation.

–Reset timer on match with optional interrupt generation.

Product data sheet Rev. 9.10 — 8 September 2020 33 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

•Up to four external outputs corresponding to match registers, with the following

capabilities:

–Set LOW on match.

–Set HIGH on match.

–Toggle on match.

–Do nothing on match.

•Up to two match registers can be used to generate timed DMA requests.

8.22 Pulse width modulator

The PWM is based on the standard Timer block and inherits all of its features, although

only the PWM function is pinned out on the LPC17xx. The Timer is designed to count

cycles of the system derived clock and optionally switch pins, generate interrupts or

perform other actions when specified timer values occur, based on seven match registers.

The PWM function is in addition to these features, and is based on match register events.

The ability to separately control rising and falling edge locations allows the PWM to be

used for more applications. For instance, multi-phase motor control typically requires

three non-overlapping PWM outputs with individual control of all three pulse widths and

positions.

Two match registers can be used to provide a single edge controlled PWM output. One

match register (PWMMR0) controls the PWM cycle rate, by resetting the count upon

match. The other match register controls the PWM edge position. Additional single edge

controlled PWM outputs require only one match register each, since the repetition rate is

the same for all PWM outputs. Multiple single edge controlled PWM outputs will all have a

rising edge at the beginning of each PWM cycle, when an PWMMR0 match occurs.

Three match registers can be used to provide a PWM output with both edges controlled.

Again, the PWMMR0 match register controls the PWM cycle rate. The other match

registers control the two PWM edge positions. Additional double edge controlled PWM

outputs require only two match registers each, since the repetition rate is the same for all

PWM outputs.

With double edge controlled PWM outputs, specific match registers control the rising and

falling edge of the output. This allows both positive going PWM pulses (when the rising

edge occurs prior to the falling edge), and negative going PWM pulses (when the falling

edge occurs prior to the rising edge).

8.22.1 Features

•One PWM block with Counter or Timer operation (may use the peripheral clock or one

of the capture inputs as the clock source).

•Seven match registers allow up to 6 single edge controlled or 3 double edge

controlled PWM outputs, or a mix of both types. The match registers also allow:

–Continuous operation with optional interrupt generation on match.

–Stop timer on match with optional interrupt generation.

–Reset timer on match with optional interrupt generation.

Product data sheet Rev. 9.10 — 8 September 2020 34 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

•Supports single edge controlled and/or double edge controlled PWM outputs. Single

edge controlled PWM outputs all go high at the beginning of each cycle unless the

output is a constant low. Double edge controlled PWM outputs can have either edge

occur at any position within a cycle. This allows for both positive going and negative

going pulses.

•Pulse period and width can be any number of timer counts. This allows complete

flexibility in the trade-off between resolution and repetition rate. All PWM outputs will

occur at the same repetition rate.

•Double edge controlled PWM outputs can be programmed to be either positive going

or negative going pulses.

•Match register updates are synchronized with pulse outputs to prevent generation of

erroneous pulses. Software must ‘release’ new match values before they can become

effective.

•May be used as a standard 32-bit timer/counter with a programmable 32-bit prescaler

if the PWM mode is not enabled.

8.23 Motor control PWM

The motor control PWM is a specialized PWM supporting 3-phase motors and other

combinations. Feedback inputs are provided to automatically sense rotor position and use

that information to ramp speed up or down. An abort input is also provided that causes the

PWM to immediately release all motor drive outputs. At the same time, the motor control

PWM is highly configurable for other generalized timing, counting, capture, and compare

applications.

8.24 Quadrature Encoder Interface (QEI)

A quadrature encoder, also known as a 2-channel incremental encoder, converts angular

displacement into two pulse signals. By monitoring both the number of pulses and the

relative phase of the two signals, the user can track the position, direction of rotation, and

velocity. In addition, a third channel, or index signal, can be used to reset the position

counter. The quadrature encoder interface decodes the digital pulses from a quadrature

encoder wheel to integrate position over time and determine direction of rotation. In

addition, the QEI can capture the velocity of the encoder wheel.

8.24.1 Features

•Tracks encoder position.

•Increments/decrements depending on direction.

•Programmable for 2 or 4 position counting.

•Velocity capture using built-in timer.

•Velocity compare function with “less than” interrupt.

•Uses 32-bit registers for position and velocity.

•Three position compare registers with interrupts.

•Index counter for revolution counting.

•Index compare register with interrupts.

•Can combine index and position interrupts to produce an interrupt for whole and

partial revolution displacement.

Product data sheet Rev. 9.10 — 8 September 2020 35 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

•Digital filter with programmable delays for encoder input signals.

•Can accept decoded signal inputs (clk and direction).

•Connected to APB.

8.25 Repetitive Interrupt (RI) timer

The repetitive interrupt timer provides a free-running 32-bit counter which is compared to

a selectable value, generating an interrupt when a match occurs. Any bits of the

timer/compare can be masked such that they do not contribute to the match detection.

The repetitive interrupt timer can be used to create an interrupt that repeats at

predetermined intervals.

8.25.1 Features

•32-bit counter running from PCLK. Counter can be free-running or be reset by a

generated interrupt.

•32-bit compare value.

•32-bit compare mask. An interrupt is generated when the counter value equals the

compare value, after masking. This allows for combinations not possible with a simple

compare.

8.26 Arm Cortex-M3 system tick timer

The Arm Cortex-M3 includes a system tick timer (SYSTICK) that is intended to generate a

dedicated SYSTICK exception at a 10 ms interval. In the LPC17xx, this timer can be

clocked from the internal AHB clock or from a device pin.

8.27 Watchdog timer

The purpose of the watchdog is to reset the microcontroller within a reasonable amount of

time if it enters an erroneous state. When enabled, the watchdog will generate a system

reset if the user program fails to ‘feed’ (or reload) the watchdog within a predetermined

amount of time.

8.27.1 Features

•Internally resets chip if not periodically reloaded.

•Debug mode.

•Enabled by software but requires a hardware reset or a watchdog reset/interrupt to be

disabled.

•Incorrect/Incomplete feed sequence causes reset/interrupt if enabled.

•Flag to indicate watchdog reset.

•Programmable 32-bit timer with internal prescaler.

•Selectable time period from (Tcy(WDCLK)  256  4) to (Tcy(WDCLK)  232  4) in

multiples of Tcy(WDCLK)  4.

•The Watchdog Clock (WDCLK) source can be selected from the Internal RC (IRC)

oscillator, the RTC oscillator, or the APB peripheral clock. This gives a wide range of

potential timing choices of Watchdog operation under different power reduction

Product data sheet Rev. 9.10 — 8 September 2020 36 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

conditions. It also provides the ability to run the WDT from an entirely internal source

that is not dependent on an external crystal and its associated components and wiring

for increased reliability.

•Includes lock/safe feature.

8.28 RTC and backup registers

The RTC is a set of counters for measuring time when system power is on, and optionally

when it is off. The RTC on the LPC17xx is designed to have extremely low power

consumption, i.e. less than 1 A. The RTC will typically run from the main chip power

supply, conserving battery power while the rest of the device is powered up. When

operating from a battery, the RTC will continue working down to 2.1 V. Battery power can

be provided from a standard 3 V Lithium button cell.

An ultra-low power 32 kHz oscillator will provide a 1 Hz clock to the time counting portion

of the RTC, moving most of the power consumption out of the time counting function.

The RTC includes a calibration mechanism to allow fine-tuning the count rate in a way

that will provide less than 1 second per day error when operated at a constant voltage and

temperature. A clock output function (see Section 8.29.4) makes measuring the oscillator

rate easy and accurate.

The RTC contains a small set of backup registers (20 bytes) for holding data while the

main part of the LPC17xx is powered off.

The RTC includes an alarm function that can wake up the LPC17xx from all reduced

power modes with a time resolution of 1 s.

8.28.1 Features

•Measures the passage of time to maintain a calendar and clock.

•Ultra low power design to support battery powered systems.

•Provides Seconds, Minutes, Hours, Day of Month, Month, Year, Day of Week, and

Day of Year.

•Dedicated power supply pin can be connected to a battery or to the main 3.3 V.

•Periodic interrupts can be generated from increments of any field of the time registers.

•Backup registers (20 bytes) powered by VBAT.

•RTC power supply is isolated from the rest of the chip.

8.29 Clocking and power control

8.29.1 Crystal oscillators

The LPC17xx include three independent oscillators. These are the main oscillator, the IRC

oscillator, and the RTC oscillator. Each oscillator can be used for more than one purpose

as required in a particular application. Any of the three clock sources can be chosen by

software to drive the main PLL and ultimately the CPU.

Following reset, the LPC17xx will operate from the Internal RC oscillator until switched by

software. This allows systems to operate without any external crystal and the bootloader

code to operate at a known frequency.

Product data sheet Rev. 9.10 — 8 September 2020 37 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

See Figure 6 for an overview of the LPC17xx clock generation.

8.29.1.1 Internal RC oscillator

The IRC may be used as the clock source for the WDT, and/or as the clock that drives the

PLL and subsequently the CPU. The nominal IRC frequency is 4 MHz. The IRC is

trimmed to 1 % accuracy over the entire voltage and temperature range.

Upon power-up or any chip reset, the LPC17xx use the IRC as the clock source. Software

may later switch to one of the other available clock sources.

8.29.1.2 Main oscillator

The main oscillator can be used as the clock source for the CPU, with or without using the

PLL. The main oscillator also provides the clock source for the dedicated USB PLL.

The main oscillator operates at frequencies of 1 MHz to 25 MHz. This frequency can be

boosted to a higher frequency, up to the maximum CPU operating frequency, by the main

PLL. The clock selected as the PLL input is PLLCLKIN. The Arm processor clock

frequency is referred to as CCLK elsewhere in this document. The frequencies of

PLLCLKIN and CCLK are the same value unless the PLL is active and connected. The

clock frequency for each peripheral can be selected individually and is referred to as

PCLK. Refer to Section 8.29.2 for additional information.

8.29.1.3 RTC oscillator

The RTC oscillator can be used as the clock source for the RTC block, the main PLL,

and/or the CPU.

Fig 6. LPC17xx clocking generation block diagram

MAIN

OSCILLATOR

INTERNAL

OSCILLATOR

RTC

OSCILLATOR

MAIN PLL

WATCHDOG

TIMER

REAL-TIME

CLOCK

CPU

CLOCK

DIVIDER

PERIPHERAL

CLOCK

GENERATOR

USB BLOCK

ARM

CORTEX-M3

ETHERNET

BLOCK

DMA

GPIO

NVIC

USB

CLOCK

DIVIDER

system

clock

select

(CLKSRCSEL)

USB clock config

(USBCLKCFG)

CPU clock config

(CCLKCFG)

pllclk

CCLK/8

CCLK/6

CCLK/4

CCLK/2

CCLK

pclkWDT

rtclk = 1Hz

usbclk

(48 MHz)

cclk

USB PLL

USB PLL enable

main PLL enable

32 kHz

APB peripherals

LPC17xx

002aad94

Product data sheet Rev. 9.10 — 8 September 2020 38 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

8.29.2 Main PLL (PLL0)

The PLL0 accepts an input clock frequency in the range of 32 kHz to 25 MHz. The input

frequency is multiplied up to a high frequency, then divided down to provide the actual

clock used by the CPU and/or the USB block.

The PLL0 input, in the range of 32 kHz to 25 MHz, may initially be divided down by a

value ‘N’, which may be in the range of 1 to 256. This input division provides a wide range

of output frequencies from the same input frequency.

Following the PLL0 input divider is the PLL0 multiplier. This can multiply the input divider

output through the use of a Current Controlled Oscillator (CCO) by a value ‘M’, in the

range of 1 through 32768. The resulting frequency must be in the range of 275 MHz to

550 MHz. The multiplier works by dividing the CCO output by the value of M, then using a

phase-frequency detector to compare the divided CCO output to the multiplier input. The

error value is used to adjust the CCO frequency.

The PLL0 is turned off and bypassed following a chip Reset and by entering Power-down

mode. PLL0 is enabled by software only. The program must configure and activate the

PLL0, wait for the PLL0 to lock, and then connect to the PLL0 as a clock source.

8.29.3 USB PLL (PLL1)

The LPC17xx contain a second, dedicated USB PLL1 to provide clocking for the USB

interface.

The PLL1 receives its clock input from the main oscillator only and provides a fixed

48 MHz clock to the USB block only. The PLL1 is disabled and powered off on reset. If the

PLL1 is left disabled, the USB clock will be supplied by the 48 MHz clock from the main

PLL0.

The PLL1 accepts an input clock frequency in the range of 10 MHz to 25 MHz only. The

input frequency is multiplied up the range of 48 MHz for the USB clock using a Current

Controlled Oscillators (CCO). It is insured that the PLL1 output has a 50 % duty cycle.

8.29.4 RTC clock output

The LPC17xx feature a clock output function intended for synchronizing with external

devices and for use during system development to allow checking the internal clocks

CCLK, IRC clock, main crystal, RTC clock, and USB clock in the outside world. The RTC

clock output allows tuning the RTC frequency without probing the pin, which would distort

the results.

8.29.5 Wake-up timer

The LPC17xx begin operation at power-up and when awakened from Power-down mode

by using the 4 MHz IRC oscillator as the clock source. This allows chip operation to

resume quickly. If the main oscillator or the PLL is needed by the application, software will

need to enable these features and wait for them to stabilize before they are used as a

clock source.

When the main oscillator is initially activated, the wake-up timer allows software to ensure

that the main oscillator is fully functional before the processor uses it as a clock source

and starts to execute instructions. This is important at power on, all types of Reset, and

Product data sheet Rev. 9.10 — 8 September 2020 39 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

whenever any of the aforementioned functions are turned off for any reason. Since the

oscillator and other functions are turned off during Power-down mode, any wake-up of the

processor from Power-down mode makes use of the wake-up timer.

The Wake-up Timer monitors the crystal oscillator to check whether it is safe to begin

code execution. When power is applied to the chip, or when some event caused the chip

to exit Power-down mode, some time is required for the oscillator to produce a signal of

sufficient amplitude to drive the clock logic. The amount of time depends on many factors,

including the rate of VDD(3V3) ramp (in the case of power on), the type of crystal and its

electrical characteristics (if a quartz crystal is used), as well as any other external circuitry

(e.g., capacitors), and the characteristics of the oscillator itself under the existing ambient

conditions.

8.29.6 Power control

The LPC17xx support a variety of power control features. There are four special modes of

processor power reduction: Sleep mode, Deep-sleep mode, Power-down mode, and

Deep power-down mode. The CPU clock rate may also be controlled as needed by

changing clock sources, reconfiguring PLL values, and/or altering the CPU clock divider

value. This allows a trade-off of power versus processing speed based on application

requirements. In addition, Peripheral Power Control allows shutting down the clocks to

individual on-chip peripherals, allowing fine tuning of power consumption by eliminating all

dynamic power use in any peripherals that are not required for the application. Each of the

peripherals has its own clock divider which provides even better power control.

Integrated PMU (Power Management Unit) automatically adjust internal regulators to

minimize power consumption during Sleep, Deep sleep, Power-down, and Deep

power-down modes.

The LPC17xx also implement a separate power domain to allow turning off power to the

bulk of the device while maintaining operation of the RTC and a small set of registers for

storing data during any of the power-down modes.

8.29.6.1 Sleep mode

When Sleep mode is entered, the clock to the core is stopped. Resumption from the Sleep

mode does not need any special sequence but re-enabling the clock to the Arm core.

In Sleep mode, execution of instructions is suspended until either a Reset or interrupt

occurs. Peripheral functions continue operation during Sleep mode and may generate

interrupts to cause the processor to resume execution. Sleep mode eliminates dynamic

power used by the processor itself, memory systems and related controllers, and internal

buses.

8.29.6.2 Deep-sleep mode

In Deep-sleep mode, the oscillator is shut down and the chip receives no internal clocks.

The processor state and registers, peripheral registers, and internal SRAM values are

preserved throughout Deep-sleep mode and the logic levels of chip pins remain static.

The output of the IRC is disabled but the IRC is not powered down for a fast wake-up later.

The RTC oscillator is not stopped because the RTC interrupts may be used as the

wake-up source. The PLL is automatically turned off and disconnected. The CCLK and

USB clock dividers automatically get reset to zero.

Product data sheet Rev. 9.10 — 8 September 2020 40 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

The Deep-sleep mode can be terminated and normal operation resumed by either a

Reset or certain specific interrupts that are able to function without clocks. Since all

dynamic operation of the chip is suspended, Deep-sleep mode reduces chip power

consumption to a very low value. Power to the flash memory is left on in Deep-sleep

mode, allowing a very quick wake-up.

On wake-up from Deep-sleep mode, the code execution and peripherals activities will

resume after 4 cycles expire if the IRC was used before entering Deep-sleep mode. If the

main external oscillator was used, the code execution will resume when 4096 cycles

expire. PLL and clock dividers need to be reconfigured accordingly.

8.29.6.3 Power-down mode

Power-down mode does everything that Deep-sleep mode does, but also turns off the

power to the IRC oscillator and the flash memory. This saves more power but requires

waiting for resumption of flash operation before execution of code or data access in the

flash memory can be accomplished.

On the wake-up of Power-down mode, if the IRC was used before entering Power-down

mode, it will take IRC 60 s to start-up. After this 4 IRC cycles will expire before the code

execution can then be resumed if the code was running from SRAM. In the meantime, the

flash wake-up timer then counts 4 MHz IRC clock cycles to make the 100 s flash start-up

time. When it times out, access to the flash will be allowed. Users need to reconfigure the

PLL and clock dividers accordingly.

8.29.6.4 Deep power-down mode

The Deep power-down mode can only be entered from the RTC block. In Deep

power-down mode, power is shut off to the entire chip with the exception of the RTC

module and the RESET pin.

The LPC17xx can wake up from Deep power-down mode via the RESET pin or an alarm

match event of the RTC.

8.29.6.5 Wake-up interrupt controller

The Wake-up Interrupt Controller (WIC) allows the CPU to automatically wake up from

any enabled priority interrupt that can occur while the clocks are stopped in Deep sleep,

Power-down, and Deep power-down modes.

The WIC works in connection with the Nested Vectored Interrupt Controller (NVIC). When

the CPU enters Deep sleep, Power-down, or Deep power-down mode, the NVIC sends a

mask of the current interrupt situation to the WIC.This mask includes all of the interrupts

that are both enabled and of sufficient priority to be serviced immediately. With this

information, the WIC simply notices when one of the interrupts has occurred and then it

wakes up the CPU.

The WIC eliminates the need to periodically wake up the CPU and poll the interrupts

resulting in additional power savings.

8.29.7 Peripheral power control

A Power Control for Peripherals feature allows individual peripherals to be turned off if

they are not needed in the application, resulting in additional power savings.

Product data sheet Rev. 9.10 — 8 September 2020 41 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

8.29.8 Power domains

The LPC17xx provide two independent power domains that allow the bulk of the device to

have power removed while maintaining operation of the RTC and the backup Registers.

On the LPC17xx, I/O pads are powered by the 3.3 V (VDD(3V3)) pins, while the

VDD(REG)(3V3) pin powers the on-chip voltage regulator which in turn provides power to the

CPU and most of the peripherals.

Depending on the LPC17xx application, a design can use two power options to manage

power consumption.

The first option assumes that power consumption is not a concern and the design ties the

VDD(3V3) and VDD(REG)(3V3) pins together. This approach requires only one 3.3 V power

supply for both pads, the CPU, and peripherals. While this solution is simple, it does not

support powering down the I/O pad ring “on the fly” while keeping the CPU and

peripherals alive.

The second option uses two power supplies; a 3.3 V supply for the I/O pads (VDD(3V3)) and

a dedicated 3.3 V supply for the CPU (VDD(REG)(3V3)). Having the on-chip voltage regulator

powered independently from the I/O pad ring enables shutting down of the I/O pad power

supply “on the fly”, while the CPU and peripherals stay active.

The VBAT pin supplies power only to the RTC domain. The RTC requires a minimum of

power to operate, which can be supplied by an external battery. The device core power

(VDD(REG)(3V3)) is used to operate the RTC whenever VDD(REG)(3V3) is present. Therefore,

there is no power drain from the RTC battery when VDD(REG)(3V3) is available.

Product data sheet Rev. 9.10 — 8 September 2020 42 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

8.30 System control

8.30.1 Reset

Reset has four sources on the LPC17xx: the RESET pin, the Watchdog reset, power-on

reset (POR), and the BrownOut Detection (BOD) circuit. The RESET pin is a Schmitt

trigger input pin. Assertion of chip Reset by any source, once the operating voltage attains

a usable level, causes the RSTOUT pin to go LOW and starts the wake-up timer (see

description in Section 8.29.5). The wake-up timer ensures that reset remains asserted

until the external Reset is de-asserted, the oscillator is running, a fixed number of clocks

have passed, and the flash controller has completed its initialization. Once reset is

de-asserted, or, in case of a BOD-triggered reset, once the voltage rises above the BOD

threshold, the RSTOUT pin goes HIGH.

When the internal Reset is removed, the processor begins executing at address 0, which

is initially the Reset vector mapped from the Boot Block. At that point, all of the processor

and peripheral registers have been initialized to predetermined values.

Fig 7. Power distribution

REAL-TIME CLOCK

BACKUP REGISTERS

REGULATOR

32 kHz

OSCILLATOR

RTC POWER DOMAIN

MAIN POWER DOMAIN

002aad978

RTCX1

VBAT

VDD(REG)(3V3)

RTCX2

VDD(3V3)

VSS

to memories,

peripherals,

oscillators,

PLLs

to core

to I/O pads

ADC

DAC

ADC POWER DOMAIN

VDDA

VREFP

VREFN

VSSA

LPC17xx

ULTRA LOW-POWER

REGULATOR

POWER

SELECTOR

Product data sheet Rev. 9.10 — 8 September 2020 43 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

8.30.2 Brownout detection

The LPC17xx include 2-stage monitoring of the voltage on the VDD(REG)(3V3) pins. If this

voltage falls below 2.2 V, the BOD asserts an interrupt signal to the Vectored Interrupt

Controller. This signal can be enabled for interrupt in the Interrupt Enable Register in the

NVIC in order to cause a CPU interrupt; if not, software can monitor the signal by reading

a dedicated status register.

The second stage of low-voltage detection asserts reset to inactivate the LPC17xx when

the voltage on the VDD(REG)(3V3) pins falls below 1.85 V. This reset prevents alteration of

the flash as operation of the various elements of the chip would otherwise become

unreliable due to low voltage. The BOD circuit maintains this reset down below 1 V, at

which point the power-on reset circuitry maintains the overall reset.

Both the 2.2 V and 1.85 V thresholds include some hysteresis. In normal operation, this

hysteresis allows the 2.2 V detection to reliably interrupt, or a regularly executed event

loop to sense the condition.

8.30.3 Code security (Code Read Protection - CRP)

This feature of the LPC17xx allows user to enable different levels of security in the system

so that access to the on-chip flash and use of the JTAG and ISP can be restricted. When

needed, CRP is invoked by programming a specific pattern into a dedicated flash location.

IAP commands are not affected by the CRP.

There are three levels of the Code Read Protection.

CRP1 disables access to chip via the JTAG and allows partial flash update (excluding

flash sector 0) using a limited set of the ISP commands. This mode is useful when CRP is

required and flash field updates are needed but all sectors can not be erased.

CRP2 disables access to chip via the JTAG and only allows full flash erase and update

using a reduced set of the ISP commands.

Running an application with level CRP3 selected fully disables any access to chip via the

JTAG pins and the ISP. This mode effectively disables ISP override using P2[10] pin, too.

It is up to the user’s application to provide (if needed) flash update mechanism using IAP

calls or call reinvoke ISP command to enable flash update via UART0.

8.30.4 APB interface

The APB peripherals are split into two separate APB buses in order to distribute the bus

bandwidth and thereby reducing stalls caused by contention between the CPU and the

GPDMA controller.

CAUTION

If level three Code Read Protection (CRP3) is selected, no future factory testing can be

performed on the device.

Product data sheet Rev. 9.10 — 8 September 2020 44 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

8.30.5 AHB multilayer matrix

The LPC17xx use an AHB multilayer matrix. This matrix connects the instruction (I-code)

and data (D-code) CPU buses of the Arm Cortex-M3 to the flash memory, the main

(32 kB) static RAM, and the Boot ROM. The GPDMA can also access all of these

memories. The peripheral DMA controllers, Ethernet, and USB can access all SRAM

blocks. Additionally, the matrix connects the CPU system bus and all of the DMA

controllers to the various peripheral functions.

8.30.6 External interrupt inputs

The LPC17xx include up to 46 edge sensitive interrupt inputs combined with up to four

level sensitive external interrupt inputs as selectable pin functions. The external interrupt

inputs can optionally be used to wake up the processor from Power-down mode.

8.30.7 Memory mapping control

The Cortex-M3 incorporates a mechanism that allows remapping the interrupt vector table

to alternate locations in the memory map. This is controlled via the Vector Table Offset

The vector table may be located anywhere within the bottom 1 GB of Cortex-M3 address

space. The vector table must be located on a 128 word (512 byte) boundary because the

NVIC on the LPC17xx is configured for 128 total interrupts.

8.31 Emulation and debugging

Debug and trace functions are integrated into the Arm Cortex-M3. Serial wire debug and

trace functions are supported in addition to a standard JTAG debug and parallel trace

functions. The Arm Cortex-M3 is configured to support up to eight breakpoints and four

watch points.

Product data sheet Rev. 9.10 — 8 September 2020 45 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

9. Limiting values

[1] The following applies to the limiting values:

a) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive

static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated

maximum.

b) Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless

otherwise noted.

c) The limiting values are stress ratings only. Operating the part at these values is not recommended, and proper operation is not

guaranteed. The conditions for functional operation are specified in Table 8.

[2] Maximum/minimum voltage above the maximum operating voltage (see Table 8) and below ground that can be applied for a short time

(< 10 ms) to a device without leading to irrecoverable failure. Failure includes the loss of reliability and shorter lifetime of the device.

[3] See Table 19 for maximum operating voltage.

[4] Including voltage on outputs in 3-state mode.

[5] VDD present or not present. Compliant with the I2C-bus standard. 5.5 V can be applied to this pin when VDD is powered down.

[6] The maximum non-operating storage temperature is different than the temperature for required shelf life which should be determined

based on required shelf lifetime. Please refer to the JEDEC spec (J-STD-033B.1) for further details.

[7] Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 k series resistor.

Table 6. Limiting values

In accordance with the Absolute Maximum Rating System (IEC 60134).[1]

Symbol Parameter Conditions Min Max Unit

VDD(3V3) supply voltage (3.3 V) external rail [2] 0.5 +4.6 V

VDD(REG)(3V3) regulator supply voltage (3.3 V) [2] 0.5 +4.6 V

VDDA analog 3.3 V pad supply

voltage

[2] 0.5 +4.6 V

Vi(VBAT) input voltage on pin VBAT for the RTC [2] 0.5 +4.6 V

Vi(VREFP) input voltage on pin VREFP [2] 0.5 +4.6 V

VIA analog input voltage on ADC related pins [2][3] 0.5 +5.1 V

VIinput voltage 5 V tolerant digital I/O pins;

VDD  2.4 V

[2][4] 0.5 +5.5 VI

VDD = 0 V 0.5 +3.6

5 V tolerant open-drain pins

PIO0_27 and PIO0_28

[2][5] 0.5 +5.5

IDD supply current per supply pin - 100 mA

ISS ground current per ground pin - 100 mA

Ilatch I/O latch-up current (0.5VDD(3V3)) < VI <

(1.5VDD(3V3)); Tj < 125 C

- 100 mA

Tstg storage temperature [6] 65 +150 C

Tj(max) maximum junction temperature 150 C

Ptot(pack) total power dissipation (per

package)

based on package heat

transfer, not device power

consumption

- 1.5 W

VESD electrostatic discharge voltage human body model; all pins [7] 4000 +4000 V

Product data sheet Rev. 9.10 — 8 September 2020 46 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

10. Thermal characteristics

The average chip junction temperature, Tj (C), can be calculated using the following

equation:

(1)

•Tamb = ambient temperature (C)

•Rth(j-a) = the package junction-to-ambient thermal resistance (C/W)

•PD = sum of internal and I/O power dissipation

The internal power dissipation is the product of IDD and VDD. The I/O power dissipation of

the I/O pins is often small and many times can be negligible. However it can be significant

in some applications.

Table 7. Thermal resistance (15 %)

Symbol Parameter Conditions Max/Min Unit

LQFP100

Rth(j-a) thermal resistance from

junction to ambient

JEDEC (4.5 in  4 in); still air 38.01 C/W

Single-layer (4.5 in  3 in); still air 55.09 C/W

Rth(j-c) thermal resistance from

junction to case

9.065 C/W

TFBGA100

Rth(j-a) thermal resistance from

junction to ambient

JEDEC (4.5 in  4 in); still air 55.2 C/W

Single-layer (4.5 in  3 in); still air 45.6 C/W

Rth(j-c) thermal resistance from

junction to case

9.5 C/W

jTamb PDRth j a–





Product data sheet Rev. 9.10 — 8 September 2020 47 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

11. Static characteristics

Table 8. Static characteristics

Tamb = −40 °C to +85 °C, unless otherwise specified.

Symbol Parameter Conditions Min Typ[1] Max Unit

Supply pins

VDD(3V3) supply voltage (3.3 V) external rail [2] 2.4 3.3 3.6 V

VDD(REG)(3V3) regulator supply voltage

(3.3 V)

2.4 3.3 3.6 V

VDDA analog 3.3 V pad supply

voltage

[3][4] 2.5 3.3 3.6 V

Vi(VBAT) input voltage on pin

VBAT

[5] 2.1 3.3 3.6 V

Vi(VREFP) input voltage on pin

VREFP

[3] 2.5 3.3 VDDA V

IDD(REG)(3V3) regulator supply current

(3.3 V)

active mode; code

while(1){}

executed from flash; all

peripherals disabled;

PCLK = CCLK⁄8

CCLK = 12 MHz; PLL

disabled

[6][7] -7-mA

CCLK = 100 MHz; PLL

enabled

[6][7] -42-mA

CCLK = 100 MHz; PLL

enabled (LPC1769)

[6][8] -50-mA

CCLK = 120 MHz; PLL

enabled (LPC1769)

[6][8] -67-mA

sleep mode [6][9] -2-mA

deep sleep mode [6][10] - 240 - A

power-down mode [6][10] -31-A

deep power-down mode;

RTC running

[11] - 630 - nA

IBAT battery supply current deep power-down mode;

RTC running

VDD(REG)(3V3) present [12] - 530 - nA

VDD(REG)(3V3) not

present

[13] -

1.1 - A

IDD(IO) I/O supply current deep sleep mode [14][15] -40-nA

power-down mode [14][15] -40-nA

deep power-down mode [14] -10-nA

Product data sheet Rev. 9.10 — 8 September 2020 48 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

IDD(ADC) ADC supply current active mode;

ADC powered

[16][17] - 1.95 - mA

ADC in Power-down

mode

[16][18] - <0.2 - A

deep sleep mode [16] -38-nA

power-down mode [16] -38-nA

deep power-down mode [16] -24-nA

II(ADC) ADC input current on pin VREFP

deep sleep mode [19] - 100 - nA

power-down mode [19] - 100 - nA

deep power-down

mode

[19] - 100 - nA

Standard port pins, RESET, RTCK

IIL LOW-level input current VI = 0 V; on-chip pull-up

resistor disabled

- 0.5 10 nA

IIH HIGH-level input

current

VI = VDD(3V3); on-chip

pull-down resistor

disabled

- 0.5 10 nA

IOZ OFF-state output

current

VO = 0 V; VO = VDD(3V3);

on-chip pull-up/down

resistors disabled

- 0.5 10 nA

VIinput voltage pin configured to provide

a digital function

[20][21]

[22]

0 - 5.0 V

VOoutput voltage output active 0 - VDD(3V3) V

VIH HIGH-level input

voltage

0.7VDD(3V3) --V

VIL LOW-level input voltage - - 0.3VDD(3V3) V

Vhys hysteresis voltage 0.4 - - V

VOH HIGH-level output

voltage

IOH = 4 mA VDD(3V3) 

0.4

--V

VOL LOW-level output

voltage

IOL = 4 mA - - 0.4 V

IOH HIGH-level output

current

VOH = VDD(3V3)  0.4 V 4- - mA

IOL LOW-level output

current

VOL = 0.4 V 4 - - mA

IOHS HIGH-level short-circuit

output current

VOH = 0 V [23] --45 mA

IOLS LOW-level short-circuit

output current

VOL = VDD(3V3) [23] - - 50 mA

Ipd pull-down current VI = 5 V 10 50 150 A

Ipu pull-up current VI = 0 V 15 50 85 A

VDD(3V3) < VI < 5 V 0 0 0 A

Table 8. Static characteristics …continued

Tamb = −40 °C to +85 °C, unless otherwise specified.

Symbol Parameter Conditions Min Typ[1] Max Unit

Product data sheet Rev. 9.10 — 8 September 2020 49 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

[1] Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply voltages.

[2] For USB operation 3.0 V  VDD((3V3)  3.6 V. Guaranteed by design.

[3] VDDA and VREFP should be tied to VDD(3V3) if the ADC and DAC are not used.

[4] VDDA for DAC specs are from 2.7 V to 3.6 V.

I2C-bus pins (P0[27] and P0[28])

VIH HIGH-level input

voltage

0.7VDD(3V3) --V

VIL LOW-level input voltage - - 0.3VDD(3V3) V

Vhys hysteresis voltage - 0.05 

VDD(3V3)

-V

VOL LOW-level output

voltage

IOLS = 3 mA - - 0.4 V

ILI input leakage current VI = VDD(3V3) [24] -24A

VI = 5 V - 10 22 A

Oscillator pins

Vi(XTAL1) input voltage on pin

XTAL1

0.5 1.8 1.95 V

Vo(XTAL2) output voltage on pin

XTAL2

0.5 1.8 1.95 V

Vi(RTCX1) input voltage on pin

RTCX1

0.5 - 3.6 V

Vo(RTCX2) output voltage on pin

RTCX2

0.5 - 3.6 V

USB pins (LPC1769/68/66/65/64 only)

IOZ OFF-state output

current

0 V < VI < 3.3 V [2] --10 A

VBUS bus supply voltage [2] - - 5.25 V

VDI differential input

sensitivity voltage

(D+)  (D)[2] 0.2 - - V

VCM differential common

mode voltage range

includes VDI range [2] 0.8 - 2.5 V

Vth(rs)se single-ended receiver

switching threshold

voltage

[2] 0.8 - 2.0 V

VOL LOW-level output

voltage for

low-/full-speed

RL of 1.5 k to 3.6 V [2] - - 0.18 V

VOH HIGH-level output

voltage (driven) for

low-/full-speed

RL of 15 k to GND [2] 2.8 - 3.5 V

Ctrans transceiver capacitance pin to GND [2] - - 20 pF

ZDRV driver output

impedance for driver

which is not high-speed

capable

with 33  series resistor;

steady state drive

[2][25] 36 - 44.1 

Table 8. Static characteristics …continued

Tamb = −40 °C to +85 °C, unless otherwise specified.

Symbol Parameter Conditions Min Typ[1] Max Unit

Product data sheet Rev. 9.10 — 8 September 2020 50 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

[5] The RTC typically fails when Vi(VBAT) drops below 1.6 V.

[6] VDD(REG)(3V3) = 3.3 V; Tamb = 25 C for all power consumption measurements.

[7] Applies to LPC1768/67/66/65/64/63.

[8] Applies to LPC1769 only.

[9] IRC running at 4 MHz; main oscillator and PLL disabled; PCLK = CCLK⁄8.

[10] BOD disabled.

[11] On pin VDD(REG)(3V3). IBAT = 530 nA. VDD(REG)(3V3) = 3.0 V; VBAT = 3.0 V; Tamb = 25 C.

[12] On pin VBAT; IDD(REG)(3V3) = 630 nA; VDD(REG)(3V3) = 3.0 V; VBAT = 3.0 V; Tamb = 25 C.

[13] On pin VBAT; VBAT = 3.0 V; Tamb = 25 C.

[14] All internal pull-ups disabled. All pins configured as output and driven LOW. VDD(3V3) = 3.3 V; Tamb = 25 C.

[15] TCK/SWDCLK pin needs to be externally pulled LOW.

[16] On pin VDDA; VDDA = 3.3 V; Tamb = 25 C. The ADC is powered if the PDN bit in the AD0CR register is set to 1 and in Power-down mode

of the PDN bit is set to 0.

[17] The ADC is powered if the PDN bit in the AD0CR register is set to 1. See LPC17xx user manual UM10360_1.

[18] The ADC is in Power-down mode if the PDN bit in the AD0CR register is set to 0. See LPC17xx user manual UM10360_1.

[19] Vi(VREFP) = 3.3 V; Tamb = 25 C.

[20] Including voltage on outputs in 3-state mode.

[21] VDD(3V3) supply voltages must be present.

[22] 3-state outputs go into 3-state mode in Deep power-down mode.

[23] Allowed as long as the current limit does not exceed the maximum current allowed by the device.

[24] To VSS.

[25] Includes external resistors of 33   1 % on D+ and D.

11.1 Power consumption

Conditions: BOD disabled.

Fig 8. Deep-sleep mode: typical regulator supply current IDD(Reg)(3V3) versus

temperature

002aaf568

temperature (°C)

−40 853510 60−15

250

350

300

400

IDD(Reg)(3V3)

(A)

200

3.6 V

3.3 V

2.4 V

Product data sheet Rev. 9.10 — 8 September 2020 51 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Conditions: BOD disabled.

Fig 9. Power-down mode: Typical regulator supply current IDD(Reg)(3V3) versus

temperature

Conditions: VDD(REG)(3V3) floating; RTC running.

Fig 10. Deep power-down mode: Typical battery supply current IBAT versus temperature

002aaf569

120

temperature (°C)

−40 853510 60−15

IDD(Reg)(3V3)

(A)

3.6 V

3.3 V

2.4 V

002aag119

1.0

1.4

1.8

0.6

temperature (°C)

-40 853510 60-15

IBAT)

(μA)

Vi(VBAT) = 3.6 V

3.3 V

3.0 V

2.4 V

Product data sheet Rev. 9.10 — 8 September 2020 52 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Conditions: VBAT = 3.0 V; VDD(REG)(3V3) = 3.0 V; RTC running.

Fig 11. Deep power-down mode: Typical regulator supply current IDD(REG)(3V3) and battery

supply current IBAT versus temperature

002aag120

temperature (°C)

-40 853510 60-15

0.8

1.6

0.4

1.2

2.0

IDD(REG)(3V3)

IBAT

IDD(REG)(3V3)/IBAT

(µA)

Product data sheet Rev. 9.10 — 8 September 2020 53 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

11.2 Peripheral power consumption

The supply current per peripheral is measured as the difference in supply current between

the peripheral block enabled and the peripheral block disabled in the PCONP register. All

other blocks are disabled and no code is executed. Measured on a typical sample at

Tamb = 25 C. The peripheral clock PCLK = CCLK/4.

[1] The combined current of several peripherals running at the same time can be less than the sum of each individual peripheral current

measured separately.

Table 9. Power consumption for individual analog and digital blocks

Peripheral Conditions Typical supply current in mA;

CCLK =

Notes

12 MHz 48 MHz 100 MHz

Timer 0.03 0.11 0.23 Average current per timer

UART 0.07 0.26 0.53 Average current per UART

PWM 0.05 0.20 0.41

Motor control

PWM

0.05 0.21 0.42

I2C 0.02 0.08 0.16 Average current per I2C

SPI 0.02 0.06 0.13

SSP1 0.04 0.16 0.32

ADC PCLK = 12 MHz for CCLK = 12 MHz

and 48 MHz; PCLK = 12.5 MHz for

CCLK = 100 MHz

2.12 2.09 2.07

CAN PCLK = CCLK/6 0.13 0.49 1.00 Average current per CAN

CAN0, CAN1,

acceptance filter

PCLK = CCLK/6 0.22 0.85 1.73 Both CAN blocks and

acceptance filter[1]

DMA PCLK = CCLK 1.33 5.10 10.36

QEI 0.05 0.20 0.41

GPIO 0.33 1.27 2.58

I2S 0.09 0.34 0.70

USB and PLL1 0.94 1.32 1.94

Ethernet Ethernet block enabled in the PCONP

0.49 1.87 3.79

Ethernet

connected

Ethernet initialized, connected to

network, and running web server

example.

- - 5.19

Product data sheet Rev. 9.10 — 8 September 2020 54 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

11.3 Electrical pin characteristics

Conditions: VDD(REG)(3V3) = VDD(3V3) = 3.3 V; standard port pins.

Fig 12. Typical HIGH-level output voltage VOH versus HIGH-level output source current

IOH

Conditions: VDD(REG)(3V3) = VDD(3V3) = 3.3 V; standard port pins.

Fig 13. Typical LOW-level output current IOL versus LOW-level output voltage VOL

IOH (mA)

0 24168

002aaf112

2.8

2.4

3.2

3.6

VOH

(V)

2.0

T = 85 °C

25 °C

−40 °C

VOL (V)

0 0.60.40.2

002aaf111

IOL

(mA)

T = 85 °C

25 °C

−40 °C

Product data sheet Rev. 9.10 — 8 September 2020 55 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Conditions: VDD(REG)(3V3) = VDD(3V3) = 3.3 V; standard port pins.

Fig 14. Typical pull-up current Ipu versus input voltage VI

Conditions: VDD(REG)(3V3) = VDD(3V3) = 3.3 V; standard port pins.

Fig 15. Typical pull-down current Ipd versus input voltage VI

0 54231

002aaf108

−30

−50

−10

Ipu

(A)

−70

T = 85 °C

25 °C

−40 °C

VI (V)

002aaf109

VI (V)

0 53241

Ipd

(A)

−10

T = 85 °C

25 °C

−40 °C

Product data sheet Rev. 9.10 — 8 September 2020 56 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

12. Dynamic characteristics

12.1 Flash memory

[1] Number of program/erase cycles.

[2] Programming times are given for writing 256 bytes from RAM to the flash. Data must be written to the flash in blocks of 256 bytes.

12.2 External clock

[1] Parameters are valid over operating temperature range unless otherwise specified.

[2] Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply voltages.

Table 10. Flash characteristics

Tamb = −40 °C to +85 °C, unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

Nendu endurance [1] 10 000 100 000 - cycles

tret retention time powered 10 - - years

unpowered 20 - - years

ter erase time sector or multiple

consecutive sectors

95 100 105 ms

tprog programming time [2] 0.95 1 1.05 ms

Table 11. Dynamic characteristic: external clock

Tamb = −40 °C to +85 °C; VDD(3V3) over specified ranges.[1]

Symbol Parameter Conditions Min Typ[2] Max Unit

fosc oscillator frequency 1 - 25 MHz

Tcy(clk) clock cycle time 40 - 1000 ns

tCHCX clock HIGH time Tcy(clk)  0.4 - - ns

tCLCX clock LOW time Tcy(clk)  0.4 - - ns

tCLCH clock rise time - - 5 ns

tCHCL clock fall time - - 5 ns

Fig 16. External clock timing (with an amplitude of at least Vi(RMS) = 200 mV)

CHCL

CLCX

CHCX

cy(clk)

CLCH

002aaa90

Product data sheet Rev. 9.10 — 8 September 2020 57 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

12.3 Internal oscillators

[1] Parameters are valid over operating temperature range unless otherwise specified.

[2] Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply voltages.

12.4 I/O pins

[1] Applies to standard I/O pins.

Table 12. Dynamic characteristic: internal oscillators

Tamb = −40 °C to +85 °C; 2.7 V ≤ VDD(REG)(3V3) ≤ 3.6 V.[1]

Symbol Parameter Conditions Min Typ[2] Max Unit

fosc(RC) internal RC oscillator frequency - 3.96 4.02 4.04 MHz

fi(RTC) RTC input frequency - - 32.768 - kHz

Conditions: Frequency values are typical values. 4 MHz  1 % accuracy is guaranteed for

2.7 V  VDD(REG)(3V3)  3.6 V and Tamb = 40 C to +85 C. Variations between parts may cause

the IRC to fall outside the 4 MHz  1 % accuracy specification for voltages below 2.7 V.

Fig 17. Internal RC oscillator frequency versus temperature

002aaf107

temperature (°C)

-40 853510 60-15

4.024

4.032

4.020

4.028

4.036

fosc(RC)

(MHz)

4.016

VDD(REG)(3V3) = 3.6 V

3.3 V

3.0 V

2.7 V

2.4 V

Table 13. Dynamic characteristic: I/O pins[1]

Tamb = −40 °C to +85 °C; VDD(3V3) over specified ranges.

Symbol Parameter Conditions Min Typ Max Unit

trrise time pin configured as output 3.0 - 5.0 ns

tffall time pin configured as output 2.5 - 5.0 ns

Product data sheet Rev. 9.10 — 8 September 2020 58 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

12.5 I2C-bus

[1] See the I2C-bus specification UM10204 for details.

[2] Parameters are valid over operating temperature range unless otherwise specified.

[3] A device must internally provide a hold time of at least 300 ns for the SDA signal (with respect to the

VIH(min) of the SCL signal) to bridge the undefined region of the falling edge of SCL.

[4] Cb = total capacitance of one bus line in pF.

[5] The maximum tf for the SDA and SCL bus lines is specified at 300 ns. The maximum fall time for the SDA

output stage tf is specified at 250 ns. This allows series protection resistors to be connected in between the

SDA and the SCL pins and the SDA/SCL bus lines without exceeding the maximum specified tf.

[6] In Fast-mode Plus, fall time is specified the same for both output stage and bus timing. If series resistors

are used, designers should allow for this when considering bus timing.

[7] tHD;DAT is the data hold time that is measured from the falling edge of SCL; applies to data in transmission

and the acknowledge.

[8] The maximum tHD;DAT could be 3.45 s and 0.9 s for Standard-mode and Fast-mode but must be less than

the maximum of tVD;DAT or tVD;ACK by a transition time (see the I2C-bus specification UM10204). This

maximum must only be met if the device does not stretch the LOW period (tLOW) of the SCL signal. If the

clock stretches the SCL, the data must be valid by the set-up time before it releases the clock.

[9] tSU;DAT is the data set-up time that is measured with respect to the rising edge of SCL; applies to data in

transmission and the acknowledge.

[10] A Fast-mode I2C-bus device can be used in a Standard-mode I2C-bus system but the requirement tSU;DAT =

250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period

of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next

data bit to the SDA line tr(max) + tSU;DAT = 1000 + 250 = 1250 ns (according to the Standard-mode I2C-bus

specification) before the SCL line is released. Also the acknowledge timing must meet this set-up time.

Table 14. Dynamic characteristic: I2C-bus pins[1]

Tamb = −40 °C to +85 °C.[2]

Symbol Parameter Conditions Min Max Unit

fSCL SCL clock

frequency

Standard-mode 0 100 kHz

Fast-mode 0 400 kHz

Fast-mode Plus 0 1 MHz

tffall time [3][4][5][6] of both SDA and

SCL signals

Standard-mode

- 300 ns

Fast-mode 20 + 0.1  Cb300 ns

Fast-mode Plus - 120 ns

tLOW LOW period of

the SCL clock

Standard-mode 4.7 - s

Fast-mode 1.3 - s

Fast-mode Plus 0.5 - s

tHIGH HIGH period of

the SCL clock

Standard-mode 4.0 - s

Fast-mode 0.6 - s

Fast-mode Plus 0.26 - s

tHD;DAT data hold time [3][7][8] Standard-mode 0 - s

Fast-mode 0 - s

Fast-mode Plus 0 - s

tSU;DAT data set-up

time

[9][10] Standard-mode 250 - ns

Fast-mode 100 - ns

Fast-mode Plus 50 - ns

Product data sheet Rev. 9.10 — 8 September 2020 59 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

12.6 I2S-bus interface

Remark: The I2S-bus interface is available on parts LPC1769/68/67/66/65/63. See

Table 2.

[1] CCLK = 20 MHz; peripheral clock to the I2S-bus interface PCLK = CCLK⁄4; I2S clock cycle time Tcy(clk) = 1600 ns, corresponds to the SCK

signal in the I2S-bus specification.

Fig 18. I2C-bus pins clock timing

002aaf425

70 %

30 %

70 %

30 %

70 %

30 %

70 %

30 %

tHD;DAT

1 / fSCL

70 %

30 % 70 %

30 %

tVD;DAT

tHIGH

tLOW

tSU;DAT

Table 15. Dynamic characteristics: I2S-bus interface pins

Tamb = −40 °C to +85 °C.

Symbol Parameter Conditions Min Typ Max Unit

common to input and output

trrise time [1] - - 35 ns

tffall time [1] - - 35 ns

tWH pulse width HIGH on pins I2STX_CLK and

I2SRX_CLK

[1] 0.495  Tcy(clk) -- -

tWL pulse width LOW on pins I2STX_CLK and

I2SRX_CLK

[1] - - 0.505  Tcy(clk) ns

output

tv(Q) data output valid time on pin I2STX_SDA [1] - - 30 ns

on pin I2STX_WS [1] - - 30 ns

input

tsu(D) data input set-up time on pin I2SRX_SDA [1] 3.5 - - ns

th(D) data input hold time on pin I2SRX_SDA [1] 4.0 - - ns

Product data sheet Rev. 9.10 — 8 September 2020 60 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Fig 19. I2S-bus timing (output)

Fig 20. I2S-bus timing (input)

002aad99

2STX_CLK

2STX_SDA

I2STX_WS

cy(clk)

tWH tWL

tv(Q)

002aae15

cy(clk)

tWH

tsu(D) th(D)

tsu(D) tsu(D)

tWL

2SRX_CLK

2SRX_SDA

I2SRX_WS

Product data sheet Rev. 9.10 — 8 September 2020 61 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

12.7 SSP interface

The maximum SSP speed is 33 Mbit/s in master mode or 8 Mbit/s in slave mode. In slave

mode, the maximum SSP clock rate must be 1/12 of the SSP PCLK clock rate.

Table 16. Dynamic characteristics: SSP pins in SPI mode

CL = 30 pF for all SSP pins; Tamb = −40 °C to 85 °C; VDD(3V3) = 3.3 V to 3.6 V; input slew = 1 ns;

sampled at 10 % and 90 % of the signal level. Values guaranteed by design.

Symbol Parameter Conditions Min Max Unit

SSP master

tDS data set-up time in SPI mode 16.1 - ns

tDH data hold time in SPI mode 0 - ns

tv(Q) data output valid time in SPI mode - 2.5 ns

th(Q) data output hold time in SPI mode 0 - ns

SSP slave

tDS data set-up time in SPI mode 16.1 - ns

tDH data hold time in SPI mode 0 - ns

tv(Q) data output valid time in SPI mode - 3*Tcy(PCLK) + 2.5 ns

th(Q) data output hold time in SPI mode 0 - ns

Fig 21. SSP master timing in SPI mode

SCK (CPOL = 0)

MOSI

MISO

Tcy(clk)

tDS tDH

tv(Q)

DATA VALID DATA VALID

th(Q)

SCK (CPOL = 1)

DATA VALID DATA VALID

MOSI

MISO

tDS tDH

DATA VALID DATA VALID

th(Q)

DATA VALID DATA VALID

tv(Q)

CPHA = 1

CPHA = 0

002aae829

Product data sheet Rev. 9.10 — 8 September 2020 62 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Fig 22. SSP slave timing in SPI mode

SCK (CPOL = 0)

MOSI

MISO

Tcy(clk)

tDS tDH

tv(Q)

DATA VALID DATA VALID

th(Q)

SCK (CPOL = 1)

DATA VALID DATA VALID

MOSI

MISO

tDS tDH

tv(Q)

DATA VALID DATA VALID

th(Q)

DATA VALID DATA VALID

CPHA = 1

CPHA = 0

002aae830

Product data sheet Rev. 9.10 — 8 September 2020 63 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

12.8 USB interface

Remark: The USB controller is available as a device/Host/OTG controller on parts

LPC1769/68/66/65 and as device-only controller on part LPC1764.

[1] Characterized but not implemented as production test. Guaranteed by design.

Table 17. Dynamic characteristics: USB pins (full-speed)

CL = 50 pF; Rpu = 1.5 kΩ on D+ to VDD(3V3); 3.0 V ≤ VDD(3V3) ≤ 3.6 V.

Symbol Parameter Conditions Min Typ Max Unit

trrise time 10 % to 90 % 8.5 - 13.8 ns

tffall time 10 % to 90 % 7.7 - 13.7 ns

tFRFM differential rise and fall time

matching

tr / tf- - 109 %

VCRS output signal crossover voltage 1.3 - 2.0 V

tFEOPT source SE0 interval of EOP see Figure 23 160 - 175 ns

tFDEOP source jitter for differential transition

to SE0 transition

see Figure 23 2 - +5 ns

tJR1 receiver jitter to next transition 18.5 - +18.5 ns

tJR2 receiver jitter for paired transitions 10 % to 90 % 9 - +9 ns

tEOPR1 EOP width at receiver must reject as

EOP; see

Figure 23

[1] 40 - - ns

tEOPR2 EOP width at receiver must accept as

EOP; see

Figure 23

[1] 82 - - ns

Fig 23. Differential data-to-EOP transition skew and EOP width

002aab561

PERIOD

differential

data lines

crossover point

source EOP width: tFEOPT

receiver EOP width: tEOPR1, tEOPR

crossover point

extended

differential data to

SE0/EOP skew

n TPERIOD + tFDEOP

Product data sheet Rev. 9.10 — 8 September 2020 64 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

12.9 SPI

[1] TSPICYC = (Tcy(PCLK)  n)  0.5 %, n is the SPI clock divider value (n  8); PCLK is derived from the

processor clock CCLK.

[2] Timing parameters are measured with respect to the 50 % edge of the clock SCK and the 10 % (90 %)

edge of the data signal (MOSI or MISO).

Table 18. Dynamic characteristics of SPI pins

Tamb = −40 °C to +85 °C.

Symbol Parameter Min Typ Max Unit

Tcy(PCLK) PCLK cycle time 10 - - ns

TSPICYC SPI cycle time [1] 79.6 - - ns

tSPICLKH SPICLK HIGH time 0.485  TSPICYC -- ns

tSPICLKL SPICLK LOW time - 0.515  TSPICYC ns

SPI master

tSPIDSU SPI data set-up time [2] 0--ns

tSPIDH SPI data hold time [2] 2  Tcy(PCLK)  5 - - ns

tSPIQV SPI data output valid time [2] 2  Tcy(PCLK) + 30 - - ns

tSPIOH SPI output data hold time [2] 2  Tcy(PCLK) + 5 - - ns

SPI slave

tSPIDSU SPI data set-up time [2] 0--ns

tSPIDH SPI data hold time [2] 2  Tcy(PCLK) + 5 - - ns

tSPIQV SPI data output valid time [2] 2  Tcy(PCLK) + 35 - - ns

tSPIOH SPI output data hold time [2] 2  Tcy(PCLK) + 15 - - ns

Fig 24. SPI master timing (CPHA = 1)

CK (CPOL = 0)

MOSI

MISO

002aad9

SPICYC

SPICLKH tSPICLKL

tSPIDSU tSPIDH

tSPIQV

D ATA V ALID DATA VALID

tSPIOH

CK (CPOL = 1)

D ATA V ALID D ATA V ALID

Product data sheet Rev. 9.10 — 8 September 2020 65 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Fig 25. SPI master timing (CPHA = 0)

Fig 26. SPI slave timing (CPHA = 1)

CK (CPOL = 0)

MOSI

MISO

002aad9

SPICYC

SPICLKH

SPICLKL

SPIDSU

SPIDH

D ATA V ALID DATA V ALID

SPIOH

CK (CPOL = 1)

D ATA V ALID D ATA V ALID

SPIQV

CK (CPOL = 0)

MOSI

MISO

002aad988

SPICYC

SPICLKH tSPICLKL

tSPIDSU tSPIDH

tSPIQV

D ATA V ALID DATA VALID

tSPIOH

CK (CPOL = 1)

D ATA V ALID D ATA V ALID

Product data sheet Rev. 9.10 — 8 September 2020 66 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

13. ADC electrical characteristics

[1] VDDA and VREFP should be tied to VDD(3V3) if the ADC and DAC are not used.

[2] The ADC is monotonic, there are no missing codes.

[3] The differential linearity error (ED) is the difference between the actual step width and the ideal step width. See Figure 28.

[4] The integral non-linearity (EL(adj)) is the peak difference between the center of the steps of the actual and the ideal transfer curve after

appropriate adjustment of gain and offset errors. See Figure 28.

[5] The offset error (EO) is the absolute difference between the straight line which fits the actual curve and the straight line which fits the

ideal curve. See Figure 28.

[6] ADCOFFS value (bits 7:4) = 2 in the ADTRM register. See LPC17xx user manual UM10360.

[7] The gain error (EG) is the relative difference in percent between the straight line fitting the actual transfer curve after removing offset

error, and the straight line which fits the ideal transfer curve. See Figure 28.

[8] The absolute error (ET) is the maximum difference between the center of the steps of the actual transfer curve of the non-calibrated

ADC and the ideal transfer curve. See Figure 28.

[9] See Figure 29.

[10] The conversion frequency corresponds to the number of samples per second.

Fig 27. SPI slave timing (CPHA = 0)

CK (CPOL = 0)

MOSI

MISO

002aad9

SPICYC

SPICLKH tSPICLKL

tSPIDSU tSPIDH

tSPIQV

D ATA V ALID DATA VALID

tSPIOH

CK (CPOL = 1)

D ATA V ALID D ATA V ALID

Table 19. ADC characteristics (full resolution)

VDDA = 2.5 V to 3.6 V; Tamb = −40 °C to +85 °C unless otherwise specified; ADC frequency 13 MHz; 12-bit resolution.[1]

Symbol Parameter Conditions Min Typ Max Unit

VIA analog input voltage 0 - VDDA V

Cia analog input capacitance - - 15 pF

EDdifferential linearity error [2][3] --1 LSB

EL(adj) integral non-linearity [4] --3 LSB

EOoffset error [5][6] --2 LSB

EGgain error [7] - - 0.5 %

ETabsolute error [8] - - 4 LSB

Rvsi voltage source interface

resistance

[9] - - 7.5 k

fclk(ADC) ADC clock frequency - - 13 MHz

fc(ADC) ADC conversion frequency [10] - - 200 kHz

Product data sheet Rev. 9.10 — 8 September 2020 67 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

[1] VDDA and VREFP should be tied to VDD(3V3) if the ADC and DAC are not used.

[2] The ADC is monotonic, there are no missing codes.

[3] The differential linearity error (ED) is the difference between the actual step width and the ideal step width. See Figure 28.

[4] The integral non-linearity (EL(adj)) is the peak difference between the center of the steps of the actual and the ideal transfer curve after

appropriate adjustment of gain and offset errors. See Figure 28.

[5] The offset error (EO) is the absolute difference between the straight line which fits the actual curve and the straight line which fits the

ideal curve. See Figure 28.

[6] The gain error (EG) is the relative difference in percent between the straight line fitting the actual transfer curve after removing offset

error, and the straight line which fits the ideal transfer curve. See Figure 28.

[7] The conversion frequency corresponds to the number of samples per second.

Table 20. ADC characteristics (lower resolution)

Tamb = −40 °C to +85 °C unless otherwise specified; 12-bit ADC used as 10-bit resolution ADC.[1]

Symbol Parameter Conditions Min Typ Max Unit

EDdifferential linearity error [2][3] -1 - LSB

EL(adj) integral non-linearity [4] -1.5 - LSB

EOoffset error [5] -2 - LSB

EGgain error [6] -2 - LSB

fclk(ADC) ADC clock frequency 3.0 V  VDDA  3.6 V - - 33 MHz

2.7 V  VDDA < 3.0 V - - 25 MHz

fc(ADC) ADC conversion frequency 3 V  VDDA  3.6 V [7] - - 500 kHz

2.7 V  VDDA < 3.0 V [7] - - 400 kHz

Product data sheet Rev. 9.10 — 8 September 2020 68 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

(1) Example of an actual transfer curve.

(2) The ideal transfer curve.

(3) Differential linearity error (ED).

(4) Integral non-linearity (EL(adj)).

(5) Center of a step of the actual transfer curve.

Fig 28. 12-bit ADC characteristics

002aad948

4095

4094

4093

4092

4091

(2)

(1)

40964090 4091 4092 4093 4094 4095

7123456

4090

(5)

(4)

(3)

1 LSB

(ideal)

ode

out

VREFP − VREFN

4096

offset

error

gain

error

offset error

VIA (LSBideal)

1 LSB =

Product data sheet Rev. 9.10 — 8 September 2020 69 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

14. DAC electrical characteristics

Remark: The DAC is available on parts LPC1769/68/67/66/65/63. See Table 2.

The values of resistor components Ri1 and Ri2 vary with temperature and input voltage and are

process-dependent (see Table 21).

Parasitic resistance and capacitance from the pad are not included in this figure.

Fig 29. ADC interface to pins AD0[n]

Table 21. ADC interface components

Component Range Description

Ri1 2 k to 5.2 kSwitch-on resistance for channel selection switch. Varies with

temperature, input voltage, and process.

Ri2 100  to 600 Switch-on resistance for the comparator input switch. Varies

with temperature, input voltage, and process.

C1 750 fF Parasitic capacitance from the ADC block level.

C2 65 fF Parasitic capacitance from the ADC block level.

C3 2.2 pF Sampling capacitor.

LPC17xx

AD0[n]

750 fF 65 fF Cia

2.2 pF

Rvsi

Ri2

100 Ω - 600 Ω

Ri1

2 kΩ - 5.2 kΩ

SS VEXT

002aaf197

ADC

COMPARATOR

BLOCK

Table 22. DAC electrical characteristics

VDDA = 2.7 V to 3.6 V; Tamb = −40 °C to +85 °C unless otherwise specified

Symbol Parameter Conditions Min Typ Max Unit

EDdifferential linearity error - 1 - LSB

EL(adj) integral non-linearity - 1.5 - LSB

EOoffset error - 0.6 - %

EGgain error - 0.6 - %

CLload capacitance - 200 - pF

RLload resistance 1 - - k

Product data sheet Rev. 9.10 — 8 September 2020 70 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

15. Application information

15.1 Suggested USB interface solutions

Remark: The USB controller is available as a device/Host/OTG controller on parts

LPC1769/68/66/65 and as device-only controller on part LPC1764.

If the LPC1769/68/67/66/65/64/63 VDD is always greater than 0 V while VBUS = 5 V, the

VBUS pin can be connected directly to the VBUS pin on the USB connector.

This applies to bus powered devices where the USB cable supplies the system power. For

systems where VDD can be 0 V and VBUS is directly applied to the VBUS pin, precautions

must be taken to reduce the voltage to below 3.6 V.

The maximum allowable voltage on the VBUS pin is 3.6 V. One method is to use a voltage

divider to connect the VBUS pin to the VBUS on the USB connector.

The voltage divider ratio should be such that the VBUS pin will be greater than 0.7VDD to

indicate a logic HIGH while below the 3.6 V allowable maximum voltage.

Use the following operating conditions:

VBUSmax = 5.25 V

VDD = 3.6 V

The voltage divider would need to provide a reduction of 3.6 V/5.25 V or ~0.686 V.

Fig 30. USB interface on a bus-powered device

LPC17xx

VDD(3V3)

1.5 kΩ

USB_UP_LED

002aad940

USB-B

connect

USB_D+

USB_D−

VBUS

VSS

RS = 33 Ω

Product data sheet Rev. 9.10 — 8 September 2020 71 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Fig 31. USB interface on a bus-powered device where VBUS = 5 V, VDD not present

LPC17xx

VDD

1.5 kΩ

USB-B

connector

USB_D+

USB_D-

VBUS

VSS

RS = 33 Ω

aaa-008962

USB_UP_LED

Fig 32. USB interface with soft-connect

LPC17xx

USB-B

connect

USB_D+

USB_CONNECT

SoftConnect switch

USB_D−

VBUS

VSS

VDD(3V3)

1.5 kΩ

RS = 33 Ω

002aad939

RS = 33 Ω

USB_UP_LED

Product data sheet Rev. 9.10 — 8 September 2020 72 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Fig 33. USB OTG port configuration

USB_D+

USB_D−

USB_SDA

USB_SCL

RSTOUT

LPC17xx

Mini-AB

connect

33 Ω

002aad941

EINTn

RESET_N

ADR/PSW

SPEED

SUSPEND

OE_N/INT_N

SCL

SDA

INT_N

VBUS

ISP1302

USB_UP_LED

Fig 34. USB host port configuration

USB_UP_LED

USB_D+

USB_D−

USB_PWRD

15 kΩ15 kΩ

LPC17xx USB-A

connect

33 Ω

002aad942

VDD

USB_OVRCR

USB_PPWR

LM3526-L

ENA

5 V

FLAGA

OUTA

VDD

D+

D−

VBUS

VSS

Product data sheet Rev. 9.10 — 8 September 2020 73 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

15.2 Crystal oscillator XTAL input and component selection

The input voltage to the on-chip oscillators is limited to 1.8 V. If the oscillator is driven by a

clock in slave mode, it is recommended that the input be coupled through a capacitor with

Ci = 100 pF. To limit the input voltage to the specified range, choose an additional

capacitor to ground Cg which attenuates the input voltage by a factor Ci/(Ci + Cg). In slave

mode, a minimum of 200 mV(RMS) is needed.

In slave mode the input clock signal should be coupled by means of a capacitor of 100 pF

(Figure 36), with an amplitude between 200 mV(RMS) and 1000 mV(RMS). This

corresponds to a square wave signal with a signal swing of between 280 mV and 1.4 V.

The XTALOUT pin in this configuration can be left unconnected.

External components and models used in oscillation mode are shown in Figure 37 and in

Table 23 and Table 24. Since the feedback resistance is integrated on chip, only a crystal

and the capacitances CX1 and CX2 need to be connected externally in case of

fundamental mode oscillation (the fundamental frequency is represented by L, CL and

RS). Capacitance CP in Figure 37 represents the parallel package capacitance and should

not be larger than 7 pF. Parameters FOSC, CL, RS and CP are supplied by the crystal

manufacturer.

Fig 35. USB device port configuration

LPC17xx

USB-B

connect

33 Ω

002aad94

USB_UP_LED

USB_CONNECT

VDD

D+

D−

USB_D+

USB_D−

VBUS VBUS

VSS

Fig 36. Slave mode operation of the on-chip oscillator

LPC1xxx

XTAL1

100 pF Cg

002aae8

Product data sheet Rev. 9.10 — 8 September 2020 74 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

15.3 XTAL and RTCX Printed Circuit Board (PCB) layout guidelines

The crystal should be connected on the PCB as close as possible to the oscillator input

and output pins of the chip. Take care that the load capacitors Cx1, Cx2, and Cx3 in case of

third overtone crystal usage have a common ground plane. The external components

must also be connected to the ground plain. Loops must be made as small as possible in

Fig 37. Oscillator modes and models: oscillation mode of operation and external crystal

model used for CX1/CX2 evaluation

Table 23. Recommended values for CX1/CX2 in oscillation mode (crystal and external

components parameters): low frequency mode

Fundamental oscillation

frequency FOSC

Crystal load

capacitance CL

Maximum crystal

series resistance RS

External load

capacitors CX1/CX2

1 MHz to 5 MHz 10 pF < 300 18 pF, 18 pF

20 pF < 300 39 pF, 39 pF

30 pF < 300 57 pF, 57 pF

5 MHz to 10 MHz 10 pF < 300 18 pF, 18 pF

20 pF < 200 39 pF, 39 pF

30 pF < 100 57 pF, 57 pF

10 MHz to 15 MHz 10 pF < 160 18 pF, 18 pF

20 pF < 60 39 pF, 39 pF

15 MHz to 20 MHz 10 pF < 80 18 pF, 18 pF

Table 24. Recommended values for CX1/CX2 in oscillation mode (crystal and external

components parameters): high frequency mode

Fundamental oscillation

frequency FOSC

Crystal load

capacitance CL

Maximum crystal

series resistance RS

External load

capacitors CX1, CX2

15 MHz to 20 MHz 10 pF < 180 18 pF, 18 pF

20 pF < 100 39 pF, 39 pF

20 MHz to 25 MHz 10 pF < 160 18 pF, 18 pF

20 pF < 80 39 pF, 39 pF

002aaf424

LPC1xxx

XTALIN XTALOUT

CX2

CX1

XTAL

=CLCP

Product data sheet Rev. 9.10 — 8 September 2020 75 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

order to keep the noise coupled in via the PCB as small as possible. Also parasitics

should stay as small as possible. Values of Cx1 and Cx2 should be chosen smaller

accordingly to the increase in parasitics of the PCB layout.

15.4 Standard I/O pin configuration

Figure 38 shows the possible pin modes for standard I/O pins with analog input function:

•Digital output driver: Open-drain mode enabled/disabled

•Digital input: Pull-up enabled/disabled

•Digital input: Pull-down enabled/disabled

•Digital input: Repeater mode enabled/disabled

•Analog input

The default configuration for standard I/O pins is input with pull-up enabled. The weak

MOS devices provide a drive capability equivalent to pull-up and pull-down resistors.

Fig 38. Standard I/O pin configuration with analog input

VDD VDD

ESD

VSS

ESD

strong

pull-up

strong

pull-down

VDD

weak

pull-up

weak

pull-down

open-drain enable

output enable

repeater mode

enable

pull-up enable

pull-down enable

data output

data input

analog input

select analog input

002aaf27

pin configured

s digital output

driver

pin configured

as digital input

pin configured

as analog input

Product data sheet Rev. 9.10 — 8 September 2020 76 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

15.5 Reset pin configuration

Fig 39. Reset pin configuration

eset

002aaf2

Rpu

ESD

20 ns RC

GLITCH FILTER PIN

Product data sheet Rev. 9.10 — 8 September 2020 77 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

15.6 ElectroMagnetic Compatibility (EMC)

Radiated emission measurements according to the IEC61967-2 standard using the

TEM-cell method are shown for part LPC1768.

[1] IEC levels refer to Appendix D in the IEC61967-2 Specification.

Table 25. ElectroMagnetic Compatibility (EMC) for part LPC1768 (TEM-cell method)

VDD = 3.3 V; Tamb = 25 °C.

Parameter Frequency band System clock = Unit

12 MHz 24 MHz 48 MHz 72 MHz 100 MHz

Input clock: IRC (4 MHz)

maximum

peak level

150 kHz to 30 MHz 76477dBV

30 MHz to 150 MHz +1 +5 +11 +16 +9 dBV

150 MHz to 1 GHz 2 +4 +11 +12 +19 dBV

IEC level[1] -OONML-

Input clock: crystal oscillator (12 MHz)

maximum

peak level

150 kHz to 30 MHz 54478dBV

30 MHz to 150 MHz 1 +5 +10 +15 +7 dBV

150 MHz to 1 GHz 1 +6 +11 +10 +16 dBV

IEC level[1] -OONMM-

Product data sheet Rev. 9.10 — 8 September 2020 78 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

16. Package outline

Fig 40. Package outline SOT407-1 (LQFP100)

UNIT A

max. A1A2A3bpcE

(1) eH

ELL

pZywv

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

mm 1.6 0.15

0.05 1.45

1.35 0.25 0.27

0.17 0.20

0.09 14.1

13.9 0.5 16.25

15.75 1.15

0.85 7

0.08 0.080.21

DIMENSIONS (mm are the original dimensions)

Note

1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.

0.75

0.45

SOT407-1 136E20 MS-026 00-02-01

03-02-20

D(1) (1)(1)

14.1

13.9

16.25

15.75

1.15

0.85

EA1

detail X

(A )

HA2

vMB

vMA

100

7675 5150

pin 1 index

0 5 10 mm

scale

LQFP100: plastic low profile quad flat package; 100 leads; body 14 x 14 x 1.4 mm

SOT407

-1

Product data sheet Rev. 9.10 — 8 September 2020 79 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Fig 41. Package outline SOT926-1 (TFBGA100)

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

SOT926-1 - - - - - - - - -

SOT926-

05-12-09

05-12-22

UNIT A

max

mm 1.2 0.4

0.3 0.8

0.65 0.5

0.4 9.1

8.9 9.1

8.9

DIMENSIONS (mm are the original dimensions)

FBGA100: plastic thin fine-pitch ball grid array package; 100 balls; body 9 x 9 x 0.7 mm

A2b D E e2

7.2

0.8

7.2

0.15

0.05

0.08

0.1

0 2.5 5 mm

scale

1/2 e

AC B

vMCw M

ball A1

index area

24681013579

ball A1

index area

B A

detail X

Product data sheet Rev. 9.10 — 8 September 2020 80 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Fig 42. Package outline SOT1450-2 LPC1768UK (WLCSP100)

Product data sheet Rev. 9.10 — 8 September 2020 81 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

17. Soldering

Fig 43. Reflow soldering for the LQFP100 package

SOT407-1

DIMENSIONS in mm

occupied area

Footprint information for reflow soldering of LQFP100 package

AyBy

P1P2

D2 (8 ) D1

(0.125)

Ax Ay Bx By D1 D2 Gx Gy Hx HyP1 P2 C

sot407-1

solder land

Generic footprint pattern

Refer to the package outline drawing for actual layout

17.300 17.300 14.300 14.3000.500 0.560 0.2801.500 0.400 14.500 14.500 17.550 17.550

Product data sheet Rev. 9.10 — 8 September 2020 82 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Fig 44. Reflow soldering of the TFBGA100 package

DIMENSIONS in mm

PSLSPSRHxHy

SOT926

-1

solder land plus solder paste

occupied area

ootprint information for reflow soldering of TFBGA100 package

solder land

solder paste deposit

solder resist

Generic footprint pattern

Refer to the package outline drawing for actual layout

detail X

see detail X

sot926-1_fr

0.80 0.330 0.400 0.480 9.400 9.400

Product data sheet Rev. 9.10 — 8 September 2020 83 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Fig 45. Reflow soldering of the WLCSP100 package (part 1)

Product data sheet Rev. 9.10 — 8 September 2020 84 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Fig 46. Reflow soldering of the WLCSP100 package (part 2)

Product data sheet Rev. 9.10 — 8 September 2020 85 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Fig 47. Reflow soldering of the WLCSP100 package (part 3)

Product data sheet Rev. 9.10 — 8 September 2020 86 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

18. Abbreviations

19. References

[1] LPC176x/5x User manual UM10360:

http://www.nxp.com/documents/user_manual/UM10360.pdf

[2] LPC176x Errata sheet:

http://www.nxp.com/documents/errata_sheet/ES_LPC176X.pdf

[3] Technical note ADC design guidelines:

http://www.nxp.com/documents/technical_note/TN00009.pdf

Table 26. Abbreviations

Acronym Description

ADC Analog-to-Digital Converter

AHB Advanced High-performance Bus

AMBA Advanced Microcontroller Bus Architecture

APB Advanced Peripheral Bus

BOD BrownOut Detection

CAN Controller Area Network

DAC Digital-to-Analog Converter

DMA Direct Memory Access

EOP End Of Packet

GPIO General Purpose Input/Output

IRC Internal RC

IrDA Infrared Data Association

JTAG Joint Test Action Group

MAC Media Access Control

MIIM Media Independent Interface Management

OHCI Open Host Controller Interface

OTG On-The-Go

PHY Physical Layer

PLL Phase-Locked Loop

PWM Pulse Width Modulator

RIT Repetitive Interrupt Timer

RMII Reduced Media Independent Interface

SE0 Single Ended Zero

SPI Serial Peripheral Interface

SSI Serial Synchronous Interface

SSP Synchronous Serial Port

TCM Tightly Coupled Memory

TTL Transistor-Transistor Logic

UART Universal Asynchronous Receiver/Transmitter

USB Universal Serial Bus

Product data sheet Rev. 9.10 — 8 September 2020 87 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

20. Revision history

Table 27. Revision history

Document ID Release

date

Data sheet status Change

notice

Supersedes

LPC1769_68_67_66_65_64_63

v.9.10

20200908 Product data sheet - LPC1769_68_67_66_65_64 v.9.9

Modifications: •Added TFBGA100 package to rev C device revision.

LPC1769_68_67_66_65_64_63 v.9.9 20200317 Product data sheet - LPC1769_68_67_66_65_64 v.9.8

Modifications: •Added device revision C.

LPC1769_68_67_66_65_64_63 v.9.8 20180504 Product data sheet - LPC1769_68_67_66_65_64 v.9.7

Modifications: •Added Figure 45 “Reflow soldering of the WLCSP100 package (part 1)”, Figure

46 “Reflow soldering of the WLCSP100 package (part 2)”, and Figure 47

“Reflow soldering of the WLCSP100 package (part 3)”.

LPC1769_68_67_66_65_64_63 v.9.7 20170501 Product data sheet - LPC1769_68_67_66_65_64 v.9.6

Modifications: •Updated Table 2 “Ordering options”: WLCSP100 with body size 100 balls, 5.07

x 5.07 x 0.53mm; was 5.074 x 5.074 x 0.6mm.

•Updated Figure 42 “Package outline SOT1450-2 LPC1768UK (WLCSP100)”.

LPC1769_68_67_66_65_64_63 v.9.6 20150818 Product data sheet - LPC1769_68_67_66_65_64 v.9.5

Modifications: •Changed max value of tv(Q) (data output valid time) in SPI mode to 3*Tcy(PCLK) +

2.5 ns. See Table 16 “Dynamic characteristics: SSP pins in SPI mode”.

•Updated Section 2 “Features and benefits”: Added Boundary scan Description

Language (BSDL) is not available for this device.

•Updated Figure 5 “LPC17xx memory map”: APB0 slot 7 (0x4001C000) was

"reserved" and changed it to I2C0.

•Changed pins for VDD(REG)(3V3) from F4 and F0 to F4 and F10. See Table 5 “Pin

description”.

•Removed footnote 1: “5 V tolerant pad providing digital I/O functions with TTL

levels and hysteresis. This pin is pulled up to a voltage level of 2.3 V to 2.6 V”

from TDO/SWO, TCK/SWDCLK, and RTCK, pins. See Table 5 “Pin

description”.

•Added a column for GPIO pins and device order part number to the ordering

options table. See Table 2 “Ordering options”.

LPC1769_68_67_66_65_64_63 v.9.5 <tbd> Product data sheet - LPC1769_68_67_66_65_64 v.9.4

Modifications: •SSP timing diagram updated. SSP timing parameters tv(Q), th(Q), tDS, and tDH

added. See Section 12.7 “SSP interface”.

•Parameter Tj(max) added in Table 6 “Limiting values”.

•SSP maximum bit rate in master mode corrected to 33 Mbit/s.

LPC1769_68_67_66_65_64_63 v.9.4 20140404 Product data sheet - LPC1769_68_67_66_65_64 v.9.3

Modifications: •Added LPC1768UK.

•Table 5 “Pin description”: Changed RX_MCLK and TX_MCLK type from INPUT

to OUTPUT.

LPC1769_68_67_66_65_64_63 v.9.3 20140108 Product data sheet - LPC1769_68_67_66_65_64 v.9.2

Modifications: •Table 7 “Thermal resistance (±15 %)”:

–Added TFBGA100.

–Added 15 % to table title.

Product data sheet Rev. 9.10 — 8 September 2020 88 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

LPC1769_68_67_66_65_64_63 v.9.2 20131021 Product data sheet - LPC1769_68_67_66_65_64 v.9.1

Modifications: •Table 8 “Static characteristics”:

–Added Table note 3 “VDDA and VREFP should be tied to VDD(3V3) if the

ADC and DAC are not used.”

–Added Table note 4 “VDDA for DAC specs are from 2.7 V to 3.6 V.”

–VDDA/VREFP spec changed from 2.7 V to 2.5 V.

•Table 19 “ADC characteristics (full resolution)”:

–Added Table note 1 “VDDA and VREFP should be tied to VDD(3V3) if the

ADC and DAC are not used.”

–VDDA changed from 2.7 V to 2.5 V.

•Table 20 “ADC characteristics (lower resolution)”: Added Table note 1 “VDDA

and VREFP should be tied to VDD(3V3) if the ADC and DAC are not used.”

LPC1769_68_67_66_65_64_63 v.9.1 20130916 Product data sheet - LPC1769_68_67_66_65_64 v.9

Modifications: •Added Table 7 “Thermal resistance”.

•Table 6 “Limiting values”:

–Updated min/max values for VDD(3V3) and VDD(REG)(3V3).

–Updated conditions for VI.

–Updated table notes.

•Table 8 “Static characteristics”: Added Table note 15 “TCK/SWDCLK pin needs

to be externally pulled LOW.”

•Updated Section 15.1 “Suggested USB interface solutions”.

•Added Section 5 “Marking”.

•Changed title of Figure 31 from “USB interface on a self-powered device” to

“USB interface with soft-connect”.

LPC1769_68_67_66_65_64_63 v.9 20120810 Product data sheet - LPC1769_68_67_66_65_64 v.8

Modifications: •Remove table note “The peak current is limited to 25 times the corresponding

maximum current.” from Table 5 “Limiting values”.

•Change VDD(3V3) to VDD(REG)(3V3) in Section 11.3 “Internal oscillators”.

•Glitch filter constant changed to 10 ns in Table note 6 in Table 4.

•Description of RESET function updated in Table 4.

•Pull-up value added for GPIO pins in Table 4.

•Pin configuration diagram for LQFP100 package corrected (Figure 2).

LPC1769_68_67_66_65_64_63 v.8 20111114 Product data sheet - LPC1769_68_67_66_65_64 v.7

Modifications: •Pin description of USB_UP_LED pin updated in Table 4.

•Ri1 and Ri2 labels in Figure 27 updated.

•Part LPC1765FET100 added.

•Table note 10 updated in Table 4.

•Table note 1 updated in Table 12.

•Pin description of STCLK pin updated in Table 4.

•Electromagnetic compatibility data added in Section 14.6.

•Section 16 added.

Table 27. Revision history …continued

Document ID Release

date

Data sheet status Change

notice

Supersedes

Product data sheet Rev. 9.10 — 8 September 2020 89 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

LPC1769_68_67_66_65_64_63 v.7 20110405 Product data sheet - LPC1769_68_67_66_65_64 v.6

Modifications: •Pin description of pins P0[29] and P0[30] updated in Table note 5 of Table 4.

Pins are not 5 V tolerant.

•Typical value for Parameter Nendu added in Table 9.

•Parameter Vhys for I2C bus pins: typical value corrected Vhys = 0.05VDD(3V3) in

Table 7.

•Condition 3.0 V  VDD(3V3)  3.6 V added in Table 16.

•Typical values for parameters IDD(REG)(3V3) and IBAT with condition Deep

power-down mode corrected in Table 7 and Table note 9, Table note 10, and

Table note 11 updated.

•For Deep power-down mode, Figure 9 updated and Figure 10 added.

LPC1769_68_67_66_65_64_63 v.6 20100825 Product data sheet - LPC1769_68_67_66_65_64 v.5

Modifications: •Part LPC1768TFBGA added.

•Section 7.30.2; BOD level corrected.

•Added Section 10.2.

LPC1769_68_67_66_65_64_63 v.5 20100716 Product data sheet - LPC1769_68_67_66_65_64 v.4

LPC1769_68_67_66_65_64 v.4 20100201 Product data sheet - LPC1768_67_66_65_64 v.3

LPC1768_67_66_65_64 v.3 20091119 Product data sheet - LPC1768_66_65_64 v.2

LPC1768_66_65_64 v.2 20090211 Objective data sheet - LPC1768_66_65_64 v.1

LPC1768_66_65_64 v.1 20090115 Objective data sheet - -

Table 27. Revision history …continued

Document ID Release

date

Data sheet status Change

notice

Supersedes

Product data sheet Rev. 9.10 — 8 September 2020 90 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

21. Legal information

21.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design.

[2] The term ‘short data sheet’ is explained in section “Definitions”.

[3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status

information is available on the Internet at URL http://www.nxp.com.

21.2 Definitions

Draft — The document is a draft version only. The content is still under

internal review and subject to formal approval, which may result in

modifications or additions. NXP Semiconductors does not give any

representations or warranties as to the accuracy or completeness of

information included herein and shall have no liability for the consequences of

use of such information.

Short data sheet — A short data sheet is an extract from a full data sheet

with the same product type number(s) and title. A short data sheet is intended

for quick reference only and should not be relied upon to contain detailed and

full information. For detailed and full information see the relevant full data

sheet, which is available on request via the local NXP Semiconductors sales

office. In case of any inconsistency or conflict with the short data sheet, the

full data sheet shall prevail.

Product specification — The information and data provided in a Product

data sheet shall define the specification of the product as agreed between

NXP Semiconductors and its customer, unless NXP Semiconductors and

customer have explicitly agreed otherwise in writing. In no event however,

shall an agreement be valid in which the NXP Semiconductors product is

deemed to offer functions and qualities beyond those described in the

Product data sheet.

21.3 Disclaimers

Limited warranty and liability — Information in this document is believed to

be accurate and reliable. However, NXP Semiconductors does not give any

representations or warranties, expressed or implied, as to the accuracy or

completeness of such information and shall have no liability for the

consequences of use of such information. NXP Semiconductors takes no

responsibility for the content in this document if provided by an information

source outside of NXP Semiconductors.

In no event shall NXP Semiconductors be liable for any indirect, incidental,

punitive, special or consequential damages (including - without limitation - lost

profits, lost savings, business interruption, costs related to the removal or

replacement of any products or rework charges) whether or not such

damages are based on tort (including negligence), warranty, breach of

contract or any other legal theory.

Notwithstanding any damages that customer might incur for any reason

whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards

customer for the products described herein shall be limited in accordance

with the Terms and conditions of commercial sale of NXP Semiconductors.

Right to make changes — NXP Semiconductors reserves the right to make

changes to information published in this document, including without

limitation specifications and product descriptions, at any time and without

notice. This document supersedes and replaces all information supplied prior

to the publication hereof.

Suitability for use — NXP Semiconductors products are not designed,

authorized or warranted to be suitable for use in life support, life-critical or

safety-critical systems or equipment, nor in applications where failure or

malfunction of an NXP Semiconductors product can reasonably be expected

to result in personal injury, death or severe property or environmental

damage. NXP Semiconductors and its suppliers accept no liability for

inclusion and/or use of NXP Semiconductors products in such equipment or

applications and therefore such inclusion and/or use is at the customer’s own

risk.

Applications — Applications that are described herein for any of these

products are for illustrative purposes only. NXP Semiconductors makes no

representation or warranty that such applications will be suitable for the

specified use without further testing or modification.

Customers are responsible for the design and operation of their applications

and products using NXP Semiconductors products, and NXP Semiconductors

accepts no liability for any assistance with applications or customer product

design. It is customer’s sole responsibility to determine whether the NXP

Semiconductors product is suitable and fit for the customer’s applications and

products planned, as well as for the planned application and use of

customer’s third party customer(s). Customers should provide appropriate

design and operating safeguards to minimize the risks associated with their

applications and products.

NXP Semiconductors does not accept any liability related to any default,

damage, costs or problem which is based on any weakness or default in the

customer’s applications or products, or the application or use by customer’s

third party customer(s). Customer is responsible for doing all necessary

testing for the customer’s applications and products using NXP

Semiconductors products in order to avoid a default of the applications and

the products or of the application or use by customer’s third party

customer(s). NXP does not accept any liability in this respect.

Limiting values — Stress above one or more limiting values (as defined in

the Absolute Maximum Ratings System of IEC 60134) will cause permanent

damage to the device. Limiting values are stress ratings only and (proper)

operation of the device at these or any other conditions above those given in

the Recommended operating conditions section (if present) or the

Characteristics sections of this document is not warranted. Constant or

repeated exposure to limiting values will permanently and irreversibly affect

the quality and reliability of the device.

Terms and conditions of commercial sale — NXP Semiconductors

products are sold subject to the general terms and conditions of commercial

sale, as published at http://www.nxp.com/profile/terms, unless otherwise

agreed in a valid written individual agreement. In case an individual

agreement is concluded only the terms and conditions of the respective

agreement shall apply. NXP Semiconductors hereby expressly objects to

applying the customer’s general terms and conditions with regard to the

purchase of NXP Semiconductors products by customer.

No offer to sell or license — Nothing in this document may be interpreted or

construed as an offer to sell products that is open for acceptance or the grant,

conveyance or implication of any license under any copyrights, patents or

other industrial or intellectual property rights.

Document status[1][2] Product status[3] Definition

Objective [short] data sheet Development This document contains data from the objective specification for product development.

Preliminary [short] data sheet Qualification This document contains data from the preliminary specification.

Product [short] data sheet Production This document contains the product specification.

Product data sheet Rev. 9.10 — 8 September 2020 91 of 93

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

Export control — This document as well as the item(s) described herein

may be subject to export control regulations. Export might require a prior

authorization from competent authorities.

Non-automotive qualified products — Unless this data sheet expressly

states that this specific NXP Semiconductors product is automotive qualified,

the product is not suitable for automotive use. It is neither qualified nor tested

in accordance with automotive testing or application requirements. NXP

Semiconductors accepts no liability for inclusion and/or use of

non-automotive qualified products in automotive equipment or applications.

In the event that customer uses the product for design-in and use in

automotive applications to automotive specifications and standards, customer

(a) shall use the product without NXP Semiconductors’ warranty of the

product for such automotive applications, use and specifications, and (b)

whenever customer uses the product for automotive applications beyond

NXP Semiconductors’ specifications such use shall be solely at customer’s

own risk, and (c) customer fully indemnifies NXP Semiconductors for any

liability, damages or failed product claims resulting from customer design and

use of the product for automotive applications beyond NXP Semiconductors’

standard warranty and NXP Semiconductors’ product specifications.

21.4 Trademarks

Notice: All referenced brands, product names, service names and trademarks

are the property of their respective owners.

I2C-bus — logo is a trademark of NXP B.V.

22. Contact information

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: salesaddresses@nxp.com

Product data sheet Rev. 9.10 — 8 September 2020 92 of 93

continued >>

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

23. Contents

1 General description . . . . . . . . . . . . . . . . . . . . . . 1

2 Features and benefits . . . . . . . . . . . . . . . . . . . . 1

3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4 Ordering information . . . . . . . . . . . . . . . . . . . . . 4

4.1 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 4

5 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

6 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 6

7 Pinning information . . . . . . . . . . . . . . . . . . . . . . 7

7.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

7.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . 10

8 Functional description . . . . . . . . . . . . . . . . . . 21

8.1 Architectural overview. . . . . . . . . . . . . . . . . . . 21

8.2 ARM Cortex-M3 processor . . . . . . . . . . . . . . . 21

8.3 On-chip flash program memory . . . . . . . . . . . 21

8.4 On-chip SRAM . . . . . . . . . . . . . . . . . . . . . . . . 21

8.5 Memory Protection Unit (MPU). . . . . . . . . . . . 21

8.6 Memory map. . . . . . . . . . . . . . . . . . . . . . . . . . 22

8.7 Nested Vectored Interrupt Controller (NVIC) . 24

8.7.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

8.7.2 Interrupt sources. . . . . . . . . . . . . . . . . . . . . . . 24

8.8 Pin connect block . . . . . . . . . . . . . . . . . . . . . . 24

8.9 General purpose DMA controller . . . . . . . . . . 24

8.9.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

8.10 Fast general purpose parallel I/O . . . . . . . . . . 25

8.10.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

8.11 Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

8.11.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

8.12 USB interface . . . . . . . . . . . . . . . . . . . . . . . . . 27

8.12.1 USB device controller . . . . . . . . . . . . . . . . . . . 27

8.12.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

8.12.2 USB host controller . . . . . . . . . . . . . . . . . . . . 28

8.12.2.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

8.12.3 USB OTG controller . . . . . . . . . . . . . . . . . . . . 28

8.12.3.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

8.13 CAN controller and acceptance filters . . . . . . 28

8.13.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

8.14 12-bit ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

8.14.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

8.15 10-bit DAC . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

8.15.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

8.16 UARTs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

8.16.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

8.17 SPI serial I/O controller. . . . . . . . . . . . . . . . . . 30

8.17.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

8.18 SSP serial I/O controller . . . . . . . . . . . . . . . . . 30

8.18.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

8.19 I2C-bus serial I/O controllers . . . . . . . . . . . . . 31

8.19.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

8.20 I2S-bus serial I/O controllers . . . . . . . . . . . . . 32

8.20.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

8.21 General purpose 32-bit timers/external event

counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

8.21.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

8.22 Pulse width modulator . . . . . . . . . . . . . . . . . . 33

8.22.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

8.23 Motor control PWM . . . . . . . . . . . . . . . . . . . . 34

8.24 Quadrature Encoder Interface (QEI) . . . . . . . 34

8.24.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

8.25 Repetitive Interrupt (RI) timer. . . . . . . . . . . . . 35

8.25.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

8.26 ARM Cortex-M3 system tick timer . . . . . . . . . 35

8.27 Watchdog timer . . . . . . . . . . . . . . . . . . . . . . . 35

8.27.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

8.28 RTC and backup registers . . . . . . . . . . . . . . . 36

8.28.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

8.29 Clocking and power control . . . . . . . . . . . . . . 36

8.29.1 Crystal oscillators . . . . . . . . . . . . . . . . . . . . . . 36

8.29.1.1 Internal RC oscillator . . . . . . . . . . . . . . . . . . . 37

8.29.1.2 Main oscillator . . . . . . . . . . . . . . . . . . . . . . . . 37

8.29.1.3 RTC oscillator. . . . . . . . . . . . . . . . . . . . . . . . . 37

8.29.2 Main PLL (PLL0) . . . . . . . . . . . . . . . . . . . . . . 38

8.29.3 USB PLL (PLL1). . . . . . . . . . . . . . . . . . . . . . . 38

8.29.4 RTC clock output . . . . . . . . . . . . . . . . . . . . . . 38

8.29.5 Wake-up timer . . . . . . . . . . . . . . . . . . . . . . . . 38

8.29.6 Power control . . . . . . . . . . . . . . . . . . . . . . . . . 39

8.29.6.1 Sleep mode . . . . . . . . . . . . . . . . . . . . . . . . . . 39

8.29.6.2 Deep-sleep mode. . . . . . . . . . . . . . . . . . . . . . 39

8.29.6.3 Power-down mode . . . . . . . . . . . . . . . . . . . . . 40

8.29.6.4 Deep power-down mode . . . . . . . . . . . . . . . . 40

8.29.6.5 Wake-up interrupt controller . . . . . . . . . . . . . 40

8.29.7 Peripheral power control . . . . . . . . . . . . . . . . 40

8.29.8 Power domains . . . . . . . . . . . . . . . . . . . . . . . 41

8.30 System control . . . . . . . . . . . . . . . . . . . . . . . . 42

8.30.1 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

8.30.2 Brownout detection . . . . . . . . . . . . . . . . . . . . 43

8.30.3 Code security (Code Read Protection - CRP) 43

8.30.4 APB interface . . . . . . . . . . . . . . . . . . . . . . . . . 43

8.30.5 AHB multilayer matrix. . . . . . . . . . . . . . . . . . . 44

8.30.6 External interrupt inputs . . . . . . . . . . . . . . . . . 44

8.30.7 Memory mapping control . . . . . . . . . . . . . . . . 44

8.31 Emulation and debugging . . . . . . . . . . . . . . . 44

9 Limiting values . . . . . . . . . . . . . . . . . . . . . . . . 45

10 Thermal characteristics . . . . . . . . . . . . . . . . . 46

NXP Semiconductors LPC1769/68/67/66/65/64/63

32-bit ARM Cortex-M3 microcontroller

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: salesaddresses@nxp.com

Date of release: 8 September 2020

Document identifier: LPC1769_68_67_66_65_64_63

Please be aware that important notices concerning this document and the product(s)

described herein, have been included in section ‘Legal information’.

11 Static characteristics. . . . . . . . . . . . . . . . . . . . 47

11.1 Power consumption . . . . . . . . . . . . . . . . . . . . 50

11.2 Peripheral power consumption . . . . . . . . . . . . 53

11.3 Electrical pin characteristics . . . . . . . . . . . . . . 54

12 Dynamic characteristics . . . . . . . . . . . . . . . . . 56

12.1 Flash memory . . . . . . . . . . . . . . . . . . . . . . . . . 56

12.2 External clock . . . . . . . . . . . . . . . . . . . . . . . . . 56

12.3 Internal oscillators. . . . . . . . . . . . . . . . . . . . . . 57

12.4 I/O pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

12.5 I2C-bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

12.6 I2S-bus interface . . . . . . . . . . . . . . . . . . . . . . 59

12.7 SSP interface . . . . . . . . . . . . . . . . . . . . . . . . . 61

12.8 USB interface . . . . . . . . . . . . . . . . . . . . . . . . . 63

12.9 SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

13 ADC electrical characteristics . . . . . . . . . . . . 66

14 DAC electrical characteristics . . . . . . . . . . . . 69

15 Application information. . . . . . . . . . . . . . . . . . 70

15.1 Suggested USB interface solutions . . . . . . . . 70

15.2 Crystal oscillator XTAL input and component

selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

15.3 XTAL and RTCX Printed Circuit Board (PCB)

layout guidelines . . . . . . . . . . . . . . . . . . . . . . . 74

15.4 Standard I/O pin configuration . . . . . . . . . . . . 75

15.5 Reset pin configuration . . . . . . . . . . . . . . . . . . 76

15.6 ElectroMagnetic Compatibility (EMC) . . . . . . . 77

16 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 78

17 Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

18 Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . 86

19 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

20 Revision history. . . . . . . . . . . . . . . . . . . . . . . . 87

21 Legal information. . . . . . . . . . . . . . . . . . . . . . . 90

21.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 90

21.2 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

21.3 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

21.4 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 91

22 Contact information. . . . . . . . . . . . . . . . . . . . . 91

23 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92