Darlington Amplifier
Transistors
NPN Silicon
MAXIMUM RATINGS
Rating Symbol Value Unit
Collector–Emitter Voltage VCES 30 Vdc
Collector–Base Voltage VCBO 30 Vdc
Emitter–Base V oltage VEBO 10 Vdc
Collector Current — Continuous IC300 mAdc
THERMAL CHARACTERISTICS
Characteristic Symbol Max Unit
Total Device Dissipation FR–5 Board(1)
TA = 25°C
Derate above 25°C
PD225
1.8
mW
mW/°C
Thermal Resistance Junction to Ambient RJA 556 °C/W
Total Device Dissipation
Alumina Substrate,(2) TA = 25°C
Derate above 25°C
PD300
2.4
mW
mW/°C
Thermal Resistance Junction to Ambient RJA 417 °C/W
Junction and Storage Temperature TJ, Tstg –55 to +150 °C
DEVICE MARKING
MMBTA13LT1 = 1M; MMBTA14LT1 = 1N
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted)
Characteristic Symbol Min Max Unit
OFF CHARACTERISTICS
Collector–Emitter Breakdown Voltage
(IC = 100 Adc, VBE = 0) V(BR)CES 30 Vdc
Collector Cutoff Current
(VCB = 30 Vdc, IE = 0) ICBO 100 nAdc
Emitter Cutoff Current
(VEB = 10 Vdc, IC = 0) IEBO 100 nAdc
1. FR–5 = 1.0 0.75 0.062 in.
2. Alumina = 0.4 0.3 0.024 in. 99.5% alumina.
Preferred devices are ON Semiconductor recommended choices for future use and best overall value.
ON Semiconductor
Semiconductor Components Industries, LLC, 2001
March, 2001 – Rev. 1 1Publication Order Number:
MMBTA13LT1/D
MMBTA13LT1
MMBTA14LT1
MMBTA14LT1 is a Preferred Device
12
3
CASE 318–08, STYLE 6
SOT–23 (TO–236AB)
COLLECTOR 3
BASE
1
EMITTER 2
MMBTA13LT1 MMBTA14LT1
http://onsemi.com
2
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted) (Continued)
Characteristic Symbol Min Max Unit
ON CHARACTERISTICS(3)
DC Current Gain
(IC = 10 mAdc, VCE = 5.0 Vdc) MMBTA13
MMBTA14
(IC = 100 mAdc, VCE = 5.0 Vdc) MMBTA13
MMBTA14
hFE 5000
10,000
10,000
20,000
Collector–Emitter Saturation Voltage
(IC = 100 mAdc, IB = 0.1 mAdc) VCE(sat) 1.5 Vdc
Base–Emitter On Voltage
(IC = 100 mAdc, VCE = 5.0 Vdc) VBE 2.0 Vdc
SMALL–SIGNAL CHARACTERISTICS
Current–Gain — Bandwidth Product(4)
(IC = 10 mAdc, VCE = 5.0 Vdc, f = 100 MHz) fT125 MHz
3. Pulse Test: Pulse Width 300 s, Duty Cycle 2.0%.
4. fT = |hfe| ftest.
RSin
enIDEAL
TRANSISTOR
Figure 1. Transistor Noise Model
MMBTA13LT1 MMBTA14LT1
http://onsemi.com
3
NOISE CHARACTERISTICS
(VCE = 5.0 Vdc, TA = 25°C)
Figure 2. Noise Voltage
f, FREQUENCY (Hz)
50
100
200
500
20
Figure 3. Noise Current
f, FREQUENCY (Hz)
Figure 4. Total Wideband Noise Voltage
RS, SOURCE RESISTANCE (k)
Figure 5. Wideband Noise Figure
RS, SOURCE RESISTANCE (k)
5.0
50
70
100
200
30
10
20
1.0
10
10
20 50 100 200 500 1k 2k 5k 10k 20k 50k 100k
2.0
1.0
0.7
0.5
0.3
0.2
0.1
0.07
0.05
0.03
0.02
BANDWIDTH = 1.0 Hz
RS 0
IC = 1.0 mA
100 µA
10 µA
BANDWIDTH = 1.0 Hz
IC = 1.0 mA
100 µA
10 µA
en, NOISE VOLTAGE (nV)
in, NOISE CURRENT (pA)
2.0 5.0 10 20 50 100 200 500 1000
BANDWIDTH = 10 Hz TO 15.7 kHz
IC = 10 µA
100 µA
1.0 mA
8.0
10
12
14
6.0
0
4.0
1.0 2.0 5.0 10 20 50 100 200 500 1000
2.0
BANDWIDTH = 10 Hz TO 15.7 kHz
10 µA
100 µA
IC = 1.0 mA
VT, TOTAL WIDEBAND NOISE VOLTAGE (nV)
NF, NOISE FIGURE (dB)
10 20 50 100 200 500 1k 2k 5k 10k 20k 50k 100k
MMBTA13LT1 MMBTA14LT1
http://onsemi.com
4
SMALL–SIGNAL CHARACTERISTICS
Figure 6. Capacitance
VR, REVERSE VOLTAGE (VOLTS)
5.0
7.0
10
20
3.0
Figure 7. High Frequency Current Gain
IC, COLLECTOR CURRENT (mA)
Figure 8. DC Current Gain
IC, COLLECTOR CURRENT (mA)
Figure 9. Collector Saturation Region
IB, BASE CURRENT (µA)
2.0
200k
5.0
0.04
4.0
2.0
1.0
0.8
0.6
0.4
0.2
TJ = 25°C
C, CAPACITANCE (pF)
1.5
2.0
2.5
3.0
1.0
0.5
|hfe|, SMALL-SIGNAL CURRENT GAIN
hFE, DC CURRENT GAIN
VCE, COLLECTOR-EMITTER VOLTAGE (VOLTS)
0.1 0.2 0.4 1.0 2.0 4.0 10 20 40
Cibo
Cobo
0.5 1.0 2.0 0.5 10 20 50 100 200 500
VCE = 5.0 V
f = 100 MHz
TJ = 25°C
100k
70k
50k
30k
20k
10k
7.0k
5.0k
3.0k
2.0k 7.0 10 20 30 50 70 100 200 300 500
TJ = 125°C
25°C
-55°C
VCE = 5.0 V
0.1 0.2 0.5 1.0 2.0 5.0 10 20 50 100 200 500 1000
TJ = 25°C
IC = 10 mA 50 mA 250 mA 500 mA
Figure 10. “On” Voltages
IC, COLLECTOR CURRENT (mA)
Figure 11. Temperature Coefficients
IC, COLLECTOR CURRENT (mA)
1.6
5.0
-1.0
V, VOLTAGE (VOLTS)
1.4
1.2
1.0
0.8
0.6 7.0 10 20 30 50 70 100 200 300 500
VBE(sat) @ IC/IB = 1000
RV, TEMPERATURE COEFFICIENTS (mV/ C)°
θ
TJ = 25°C
VBE(on) @ VCE = 5.0 V
VCE(sat) @ IC/IB = 1000
-2.0
-3.0
-4.0
-5.0
-6.0
5.0 7.0 10 20 30 50 70 100 200 300 500
25°C TO 125°C
-55°C TO 25°C
*RVC FOR VCE(sat)
VB FOR VBE
25°C TO 125°C
-55°C TO 25°C
*APPLIES FOR IC/IB hFE/3.0
MMBTA13LT1 MMBTA14LT1
http://onsemi.com
5
Figure 12. Thermal Response
t, TIME (ms)
1.0
r(t), TRANSIENT THERMAL
2.0 5.01.00.50.20.1
RESISTANCE (NORMALIZED)
0.7
0.5
0.3
0.2
0.1
0.07
0.05
0.03
0.02
0.01
20 5010 200 500100 1.0k 2.0k 5.0k 10k
Figure 13. Active Region Safe Operating Area
VCE, COLLECTOR-EMITTER VOLTAGE (VOLTS)
1.0k
0.4
700
500
300
200
100
70
50
30
20
10 0.6 1.0 2.0 4.0 6.0 10 20 40
IC, COLLECTOR CURRENT (mA)
TA = 25°C
D = 0.5
0.2
0.1 0.05 SINGLE PULSE
SINGLE PULSE
CURRENT LIMIT
THERMAL LIMIT
SECOND BREAKDOWN LIMIT
ZθJC(t) = r(t) RθJCTJ(pk) - TC = P(pk) ZθJC(t)
ZθJA(t) = r(t) RθJATJ(pk) - TA = P(pk) ZθJA(t)
1.0 ms
100 µs
TC = 25°C
1.0 s
Design Note: Use of Transient Thermal Resistance Data
FIGURE A
tP
PPPP
t1
1/f
DUTYCYCLE t1f t1
tP
PEAK PULSE POWER = PP
MMBTA13LT1 MMBTA14LT1
http://onsemi.com
6
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values
into the equation for an ambient temperature TA of 25°C,
one can calculate the power dissipation of the device which
in this case is 225 milliwatts.
INFORMATION FOR USING THE SOT–23 SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the
total design. The footprint for the semiconductor packages
must be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
SOT–23
mm
inches
0.037
0.95
0.037
0.95
0.079
2.0
0.035
0.9
0.031
0.8
SOT–23 POWER DISSIPATION
PD = TJ(max) – TA
RθJA
PD = 150°C – 25°C
556°C/W = 225 milliwatts
The power dissipation of the SOT–23 is a function of the
pad size. This can vary from the minimum pad size for
soldering to a pad size given for maximum power dissipa-
tion. Power dissipation for a surface mount device is deter-
mined b y T J(max), the maximum rated junction temperature
of the die, RθJA, the thermal resistance from the device
junction to ambient, and the operating temperature, TA.
Using the values provided on the data sheet for the SOT–23
package, PD can be calculated as follows:
The 556°C/W for the SOT–23 package assumes the use
of the recommended footprint on a glass epoxy printed
circuit board to achieve a power dissipation of 225 milli-
watts. There are other alternatives to achieving higher
power dissipation from the SOT–23 package. Another
alternative would be to use a ceramic substrate or an
aluminum core board such as Thermal Clad. Using a
board material such as Thermal Clad, an aluminum core
board, the power dissipation can be doubled using the same
footprint.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the
rated temperature of the device. When the entire device is
heated to a high temperature, failure to complete soldering
within a short time could result in device failure. There-
fore, the following items should always be observed in
order to minimize the thermal stress to which the devices
are subjected.
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100°C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering
method, the difference shall be a maximum of 10°C.
The soldering temperature and time shall not exceed
260°C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient shall be 5°C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and
result in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied
during cooling.
* Soldering a device without preheating can cause exces-
sive thermal shock and stress which can result in damage
to the device.
MMBTA13LT1 MMBTA14LT1
http://onsemi.com
7
PACKAGE DIMENSIONS
CASE 318–08
ISSUE AF
SOT–23 (TO–236)
DJ
K
L
A
C
BS
H
GV
3
12
DIM
A
MIN MAX MIN MAX
MILLIMETERS
0.1102 0.1197 2.80 3.04
INCHES
B0.0472 0.0551 1.20 1.40
C0.0350 0.0440 0.89 1.11
D0.0150 0.0200 0.37 0.50
G0.0701 0.0807 1.78 2.04
H0.0005 0.0040 0.013 0.100
J0.0034 0.0070 0.085 0.177
K0.0140 0.0285 0.35 0.69
L0.0350 0.0401 0.89 1.02
S0.0830 0.1039 2.10 2.64
V0.0177 0.0236 0.45 0.60
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. MAXIMUM LEAD THICKNESS INCLUDES LEAD
FINISH THICKNESS. MINIMUM LEAD THICKNESS
IS THE MINIMUM THICKNESS OF BASE
MATERIAL.
STYLE 6:
PIN 1. BASE
2. EMITTER
3. COLLECTOR
MMBTA13LT1 MMBTA14LT1
http://onsemi.com
8
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031
Phone: 81–3–5740–2700
Email: r14525@onsemi.com
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
MMBTA13LT1/D
Thermal Clad is a trademark of the Bergquist Company.
Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: ONlit@hibbertco.com
N. American Technical Support: 800–282–9855 Toll Free USA/Canada