DFN4 1x1 SOT23-5L
Features
• Input voltage from 1.5 to 5.5 V
• Ultra low dropout voltage (200 mV typ. at 200 mA load)
• Very low quiescent current (20 µA typ at no load, 0.03 µA typ in off mode)
• Output voltage tolerance: ± 0.5 % (A version) or ± 2.0 % @ 25 °C (standard
version)
• 200 mA guaranteed output current
• High PSRR (80 dB@1 kHz, 50 db@100 kHz)
• Wide range of output voltages available on request: from 0.8 V up to 5.0 V in 50
mV step
• Logic-controlled electronic shutdown
• Internal soft-start
• Optional output voltage discharge feature
• Compatible with ceramic capacitor COUT = 0.47 µF
• Internal current limit and thermal protections
• Available in DFN4 1x1 and SOT23-5L packages
• Operating temperature range: -40 °C to 125 °C
Applications
• Mobile phones
• Tablets
• Digital still cameras (DSC)
• Cordless phones and similar battery-powered systems
• Portable media players
Description
The LD39020 high accuracy voltage regulator provides 200 mA of maximum current
from an input voltage ranging from 1.5 V to 5.5 V, with a typical dropout voltage of
200 mV.
It is available in DFN4 1x1 and SOT23-5L packages, allowing the maximum space
saving.
The device is stabilized with a ceramic capacitor on the output. The ultra low drop
voltage, low quiescent current and low noise features, together with the internal soft-
start circuit, make the LD39020 suitable for low power battery-operated applications.
An enable logic control function puts the LD39020 in shutdown mode allowing a total
current consumption lower than 0.1 µA. Constant current and thermal protection are
provided.
Maturity status link
LD39020
200 mA very low quiescent current linear regulator IC
LD39020
Datasheet
DS9956 - Rev 5 - January 2019
For further information contact your local STMicroelectronics sales office.
www.st.com
1Diagram
Figure 2. Block diagram
AM13852V1
VIN
GND
VOUT
OPAMP
Bias
generator
Bandgap
reference
EN
Thermal
protection
Enable
*
Note: The output discharge MOSFET is optional.
LD39020
Diagram
DS9956 - Rev 5 page 2/30
2Pin configuration
Figure 3. Pin connection (top view)
Table 1. Pin description
Pin DFN4 1x1 Pin SOT23-5L Symbol Function
1 5 OUT Output voltage
2 2 GND Common ground
3 3 EN Enable pin logic input: Low = shutdown,
High = active
4 1 IN Input voltage
Thermal pad - GND Connect to GND on the PCB
- 4 NC Not internally connected
LD39020
Pin configuration
DS9956 - Rev 5 page 3/30
3Typical application
Figure 4. Typical application circuits
LD39020
LD39020
Typical application
DS9956 - Rev 5 page 4/30
4Maximum ratings
Table 2. Absolute maximum ratings
Symbol Parameter Value Unit
VIN Input voltage - 0.3 to 7 V
VOUT Output voltage - 0.3 to VIN + 0.3 V
VEN Enable input voltage - 0.3 to 7 V
IOUT Output current Internally limited mA
PDPower dissipation Internally limited mW
TSTG Storage temperature range - 40 to 150 °C
TOP Operating junction temperature range - 40 to 125 °C
Note: Absolute maximum ratings are those values beyond which damage to the device may occur. Functional
operation under these conditions is not implied. All values are referred to GND.
Table 3. Thermal data
Symbol Parameter Value Unit
RthJA Thermal resistance junction-ambient, DFN4 1x1 250 °C/W
RthJC Thermal resistance junction-case, SOT23-5L 81 °C/W
RthJA Thermal resistance junction-ambient, SOT23-5L 255 °C/W
Table 4. ESD performance
Symbol Parameter Test conditions Value Unit
ESD ESD Protection voltage
HBM 4 kV
MM 400 V
CDM 500 V
LD39020
Maximum ratings
DS9956 - Rev 5 page 5/30
5Electrical characteristics
TJ = 25 °C, VIN = VOUT(NOM) + 1 V , CIN = COUT = 1 µF, IOUT = 1 mA, VEN = VIN, unless otherwise specified.
Table 5. Electrical characteristics for LD39020T, LD39020DT
Symbol Parameter Test conditions Min. Typ. Max. Unit
VIN Operating input voltage 1.5 5.5 V
VOUT VOUT accuracy
IOUT = 1 mA, TJ = 25 °C -2 2 %
IOUT = 1 mA,
-40 °C < TJ < 125 °C -3 3 %
∆VOUT Static line regulation (1)
VOUT(NOM) + 1 V ≤ VIN ≤ 5.5 V,
IOUT = 10 mA 0.02 %/V
-40 °C < TJ < 125 °C 0.2
∆VOUT Static load regulation
IOUT = 0 mA to 200 mA 10 mV
-40 °C < TJ < 125 °C 0.01 %/mA
VDROP Dropout voltage
IOUT = 30 mA,VOUT = 2.8 V 35
mV
IOUT = 200 mA, VOUT = 2.8 V
-40 °C < TJ < 125 °C 200 350
eNOutput noise voltage
10 Hz to 100 kHz,
IOUT = 10 mA 45 µVRMS/
VOUT
SVR Supply voltage rejection
VIN = VOUT(NOM)+ 1 V +/- VRIPPLE
VRIPPLE = 0.2 V
Freq. = 1 kHz
IOUT = 30 mA
80
dB
VIN = VOUT(NOM)+ 1 V +/- VRIPPLE,
VRIPPLE = 0.2 V
Freq. = 100 kHz, IOUT = 30 mA
55
IQQuiescent current
IOUT = 0 mA 20 40
µA
IOUT = 200 mA 100
IStandby Standby current VIN input current in OFF MODE:
VEN = GND 0.03 1 µA
ISC Short circuit current RL = 0 250 350 mA
RON Output voltage discharge
MOSFET (only on LD39020DT) 100 Ω
VEN
Enable input logic low
VIN = 1.5 V to 5.5 V
-40 °C < TJ < 125 °C 0.4
V
Enable input logic high
VIN = 1.5 V to 5.5 V
-40 °C < TJ< 125 °C 1
IEN Enable pin input current VEN = VIN 100 nA
TON (2) Turn on time 100 µs
LD39020
Electrical characteristics
DS9956 - Rev 5 page 6/30
Symbol Parameter Test conditions Min. Typ. Max. Unit
TSHDN
Thermal shutdown 160
°C
Hysteresis 20
COUT Output capacitor
Capacitance see
Figure 18. Stability area vs. (COUT,
ESR)
0.47 22 µF
1. Not applicable for Vout(nom) > 4.5 V
2. Turn-on time is time measured between the enable input just exceeding VEN high value and the output voltage just reaching
95 % of its nominal value
TJ = 25 °C, VIN = VOUT(NOM) + 1 V , CIN = COUT = 1 µF, IOUT = 1 mA, VEN = VIN, unless otherwise specified.
Table 6. Electrical characteristics for LD39020AT, LD39020ADT
Symbol Parameter Test conditions Min. Typ. Max. Unit
VIN Operating input voltage 1.5 5.5 V
VOUT VOUT accuracy
IOUT = 1 mA, TJ = 25 °C -0.5 0.5 %
IOUT = 1 mA,
-40 °C < TJ < 125 °C -1.5 1.5 %
∆VOUT Static line regulation(1)
VOUT(NOM) + 1 V ≤ VIN ≤ 5.5 V,
IOUT = 10 mA 0.02 %/V
-40 °C < TJ < 125 °C 0.2
∆VOUT Static load regulation
IOUT = 0 mA to 200 mA 10 mV
-40 °C < TJ < 125 °C 0.01 %/mA
VDROP Dropout voltage
IOUT = 30 mA, VOUT = 2.8 V 35
mV
IOUT = 200 mA, VOUT = 2.8 V
-40 °C < TJ < 125 °C 200 350
eNOutput noise voltage
10 Hz to 100 kHz,
IOUT = 10 mA 45 µVRMS /
VOUT
SVR Supply voltage rejection
VIN = VOUT(NOM)+ 1 V +/- VRIPPLE
VRIPPLE = 0.2 V
Freq. = 1 kHz
IOUT = 30 mA
80
dB
VIN = VOUT(NOM)+ 1 V +/- VRIPPLE,
VRIPPLE = 0.2 V
Freq. = 100 kHz, IOUT = 30 mA
55
IQQuiescent current
IOUT = 0 mA 20 40
µA
IOUT = 200 mA 100
IStandby Standby current VIN input current in OFF MODE:
VEN = GND 0.03 1 µA
ISC Short circuit current RL = 0 250 350 mA
LD39020
Electrical characteristics
DS9956 - Rev 5 page 7/30
Symbol Parameter Test conditions Min. Typ. Max. Unit
RON Output voltage discharge
MOSFET (only on LD39020ADT) 100 Ω
VEN
Enable input logic low
VIN = 1.5 V to 5.5 V
-40 °C < TJ < 125 °C 0.4
V
Enable input logic high
VIN = 1.5 V to 5.5 V
-40 °C < TJ < 125 °C 1
IEN Enable pin input current VEN = VIN 100 nA
TON (2) Turn on time 100 µs
TSHDN
Thermal shutdown 160 °C
Hysteresis 20
COUT Output capacitor
Capacitance see
Figure 18. Stability area vs. (COUT,
ESR)
0.47 22 µF
1. Not applicable for Vout(nom) > 4.5 V
2. Turn-on time is time measured between the enable input just exceeding VEN high value and the output voltage just reaching
95 % of its nominal value
LD39020
Electrical characteristics
DS9956 - Rev 5 page 8/30
6Application information
6.1 Soft-start function
The LD39020 has an internal soft start circuit. By increasing the startup time up to 100 µs, without the need of any
external soft start capacitor, this feature is able to keep the regulator inrush current at startup under control.
6.2 Output discharge function
The LD39020 integrates a MOSFET connected between VOUT and GND. This transistor is activated when the EN
pin goes to low logic level and has the function to quickly discharge the output capacitor when the device is
disabled by the user.
The device is available with or without auto-discharge feature.
See Table 10. DFN4 1x1 order code for more details.
6.3 Input and output capacitors
The LD39020 requires external capacitors to assure the regulator control loop stability.
Any good quality ceramic capacitor can be used but, the X5R and the X7R are suggested since they guarantee a
very stable combination of capacitance and ESR overtemperature.
Locating the input/output capacitors as closer as possible to the relative pins is recommended.
The LD39020 requires an input capacitor with a minimum value of 1 μF.
This capacitor must be located as closer as possible to the input pin of the device and returned to a clean analog
ground.
The control loop of the LD39020 is designed to work with an output ceramic capacitor.
This capacitor must meet the requirements of minimum capacitance and equivalent series resistance (ESR), as
shown in Figure 18. Stability area vs. (COUT, ESR). To assure stability, the output capacitor must maintain its ESR
and capacitance in the stable region, over the full operating temperature range.
The LD39020 shows stability with a minimum effective output capacitance of 220 nF.
However, to keep stability in all operating conditions (temperature, input voltage and load variations), a minimum
output capacitor of 0.47 µF is recommended.
The suggested combination of 1 μF input and output capacitors offers a good compromise among the stability of
the regulator, optimum transient response and total PCB area occupation.
LD39020
Application information
DS9956 - Rev 5 page 9/30
7Typical characteristics
(CIN = COUT = 1 µF, VEN to VIN, TJ = 25 °C unless otherwise specified)
Figure 5. Output voltage vs. temperature
(IOUT = 1 mA)
AM13855V1
-40 -25 0 25 55 85 125
Output Voltage [V]
Temperature [ °C]
VIN = 4.3 V, IOUT = 1 mA
Figure 6. Output voltage vs. temperature
(IOUT = 200 mA)
AM13856V1
3.2
3.22
3.24
3.26
3.28
3.3
3.32
3.34
3.36
3.38
3.4
-40 -25 0 25 55 85 125
Output Voltage [V]
Temperature [ °C]
VIN=4.3V, IOUT=200mA
Figure 7. Line regulation vs. temperature
AM13857V1
-0.15
-0.05
Line reg ulation [%/V]
Temperature [ °C]
VIN = 4.3 V to 5.5 V, IOUT = 10 mA
Figure 8. Load regulation vs. temperature
Load regulation
LD39020
Typical characteristics
DS9956 - Rev 5 page 10/30
Figure 9. Quiescent current vs. temperature
(IOUT = 0 mA)
AM13859V1
0
5
10
15
20
25
30
35
40
45
50
-40 -25 0 25 55 85 125
Quiesce nt current [µA]
Temperature [ °C]
VIN = 4.3 V, IOUT = 0 mA
Figure 10. Quiescent current vs. temperature
(IOUT = 200 mA)
AM13860V1
0
20
40
60
80
100
120
140
160
180
200
-40 -25 0 25 55 85 125
Quiescent current [µA]
Temperature [ °C]
VIN=4.3V, IOUT= 200mA
Figure 11. Shutdown current vs. temperature
AM13861V1
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
-40 -25 0 25 55 85 125
Quiescent curr ent [µA]
Temperature [°C]
VIN = 4.3 V, VEN = GND
Figure 12. Quiescent current vs. load current
AM13862V1
VIN=2V, VOUT=1V
0
20
40
60
80
100
120
140
160
0 0.02 0.04 0.06 0.08 0.1 0.12 0.14 0.16 0.18 0.2
Quiescent current [µA]
Output current [A]
Figure 13. Quiescent current vs. input voltage
AM13863V1
VIN
= 2 V, V
OUT
= 1 V
0
10
20
30
40
50
60
70
80
90
100
0 1 2 3 4 5 6
Quiescent current [µA]
Input voltage [V]
Iout = 0 mA
Iout = 1 mA
Iout = 10 mA
Figure 14. Dropout voltage vs. temperature
AM13864V1
0
25
50
75
100
125
150
175
200
225
250
275
-40 -25 0 25 55 85 125
Dropout voltage [mV]
Temperature [
°
C]
Iout = 30 mA
Iout = 50 mA
Iout = 100 mA
Iout = 200 mA
LD39020
Typical characteristics
DS9956 - Rev 5 page 11/30
Figure 15. Supply voltage rejection vs. frequency
AM13865V1
VIN
= 2 V+/-200 mV, VOUT
= 1 V, COUT = 1 µF
0
10
20
30
40
50
60
70
80
90
100
100 1000 10000 100000 1000000
SVR [dB]
Frequency [Hz]
Iout = 1 mA
Iout = 30 mA
Iout = 100 mA
Iout = 200 mA
Figure 16. Supply voltage rejection vs. input
voltage
AM13866V1
I
OUT = 30mA
, V
OUT
=
1 V
, C
OUT = 1 µF
0
10
20
30
40
50
60
70
80
90
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6
SVR [dB]
Input voltage [V]
f
= 1 kHz
f
= 10 kHz
f
= 100 kHz
Figure 17. Output noise spectral density
AM13867V1
V
IN
= 2.
0 V,
V
OUT
=
1.0 V,
C
IN
= C
OUT = 1 µF
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
10 100 1000 10000 100000
eN
[
uV / SQRT(Hz)]
Frequency [Hz]
Iout = 0 mA
Iout = 10 mA
Figure 18. Stability area vs. (COUT, ESR)
AM13868V1
0
0.2
0.4
0.6
0.8
1
1.2
1.4
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
ESR @ 100 KHz[Ω]
COUT [µF] (nominal value)
STABILITY AREA
VIN from 2 to 5.5 V, IOUT from 0 to 300 mA, CIN = 1 µF
Figure 19. Enable startup (VOUT = 1 V)
AM13869V1
VIN = 2 V, V
EN
= 0 V to VIN, IOUT = 0.2 A, V
OUT = 1 V, Tr = 5 µs
VEN
VOUT
IOUT
Figure 20. Enable startup (VOUT = 5 V)
AM13870V1
VIN
= 5.5 V, VEN = 0 V to 2 V, IOUT = 0.2 A, VOUT = 5 V, Tr = 5 µs
VEN
VOUT
IOUT
LD39020
Typical characteristics
DS9956 - Rev 5 page 12/30
Figure 21. Turn-on time (VOUT = 1 V)
AM13871V1
VIN = VEN = from 0 V to 5.5 V, IOUT = 0.2 A, V
OUT = 1 V, Tr= 5 µs
VIN
VOUT
IOUT
Figure 22. Turn-off time (VOUT = 1 V)
AM13872V1
VIN = VEN = from 5.5 V to 0 V, IOUT = 0.2 A, VOUT = 1 V, Tf = 5 µs
VIN
VOUT
IOUT
Figure 23. Turn-on time (VOUT = 5 V)
VIN
VOUT
IOUT
V
IN = VEN = from 0 V to 5.5 V, IOUT = 0.2 A, V
OUT = 5 V, T
r= 5 µs
AM13873V1
Figure 24. Turn-off time (VOUT = 5 V)
VIN
V
OUT
IOUT
V
IN = VEN = from 5.5 V to 0 V, IOUT = 0.2 A, V
OUT = 5 V, Tf= 5 µs
AM13874V1
Figure 25. Line transient (VOUT = 1 V)
VIN
VOUT
VIN = VEN = from 2 V to 3 V, IOUT = 10 mA, VOUT = 1 V, T
r= Tf= 5 µs
AM13875V1
Figure 26. Line transient (VOUT = 5 V)
VIN
VOUT
VIN = VEN = from 5.1 V to 5.5 V, IOUT = 10 mA, VOUT = 5 V, T
r=Tf= 5 µs
AM13876V1
LD39020
Typical characteristics
DS9956 - Rev 5 page 13/30
Figure 27. Load transient (VOUT = 1 V)
VOUT
IOUT
V
IN = V
EN = 2 V, IOUT = from 0 to 0.2 A, V
OUT = 1 V, tr= tf= 5 µs
AM13877V1
Figure 28. Load transient (VOUT = 5 V)
V
OUT
IOUT
V
IN = V
EN = 5.5 V, IOUT = from 0 to 0.2 A, V
OUT = 5 V, tr= tf= 5 µs
AM13878V1
LD39020
Typical characteristics
DS9956 - Rev 5 page 14/30
8Package information
In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK®
packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions
and product status are available at: www.st.com. ECOPACK® is an ST trademark.
LD39020
Package information
DS9956 - Rev 5 page 15/30
8.1 DFN4 1x1 package info
Figure 29. DFN4 1x1 package outline
8405587_A
LD39020
DFN4 1x1 package info
DS9956 - Rev 5 page 16/30
Table 7. DFN4 1x1 mechanical data
Dim.
mm
Min. Typ. Max.
A 0.34 0.37 0.40
A1 0 0.02 0.05
A3 0.10
b 0.17 0.22 0.27
D 0.95 1.00 1.05
D2 0.43 0.48 0.53
E 0.95 1.00 1.05
E2 0.43 0.48 0.53
e 0.65
L 0.20 0.25 0.30
K 0.15
LD39020
DFN4 1x1 package info
DS9956 - Rev 5 page 17/30
Figure 30. DFN4 1x1 recommended footprint
8405587_A
LD39020
DFN4 1x1 package info
DS9956 - Rev 5 page 18/30
Figure 31. DFN4 1x1 tape outline
Figure 32. DFN4 1x1 reel outline
Tape width (mm) A max. N min. W1 max. W2 max. W3 min. / max.
8 180 60 8.4 14.4 7.9 / 10.9
LD39020
DFN4 1x1 package info
DS9956 - Rev 5 page 19/30
Figure 33. DFN4 1x1 orientation
LD39020
DFN4 1x1 package info
DS9956 - Rev 5 page 20/30
8.2 SOT23-5L mechanical data
Figure 34. SOT23-5L package outline
7049676_k
Table 8. SOT23-5L package mechanical data
Dim.
mm
Min. Typ. Max.
A 0.90 1.45
A1 0 0.15
A2 0.90 1.30
b 0.30 0.50
c 0.09 0.20
D 2.95
E 1.60
e 0.95
H 2.80
L 0.30 0.60
θ 0° 8°
LD39020
SOT23-5L mechanical data
DS9956 - Rev 5 page 21/30
Figure 35. SOT23-5L recommended footprint
Note: Dimensions are in mm
LD39020
SOT23-5L mechanical data
DS9956 - Rev 5 page 22/30
8.3 SOT23-5L packing information
Figure 36. SOT23-5L tape and reel outline
Bo
Ko Ao
Po
P
D
AN
T
Table 9. SOT23-5L tape and reel mechanical data
Dim.
mm
Min. Typ. Max.
A 180
C 12.8 13.0 13.2
D 20.2
N 60
T 14.4
Ao 3.13 3.23 3.33
Bo 3.07 3.17 3.27
Ko 1.27 1.37 1.47
Po 3.9 4.0 4.1
P 3.9 4.0 4.1
LD39020
SOT23-5L packing information
DS9956 - Rev 5 page 23/30
9Order code
Table 10. DFN4 1x1 order code
Order code Output voltage (V) Auto-discharge Tolerance (%) Marking
LD39020ADTPU08R
0.8 Yes
0.5 A1
LD39020DTPU08R 2 08
LD39020ADTPU11R
1.1 Yes
0.5 A4
LD39020DTPU11R 2 11
LD39020ADTPU13R
1.3 Yes
0.5 AP
LD39020DTPU13R 2 13
LD39020ADTPU15R (1)
1.5 Yes
0.5 A6
LD39020DTPU15R 2 15
LD39020ADTPU18R
1.8 Yes
0.5 A7
LD39020DTPU18R 2 18
LD39020ATPU185R
1.85 No
0.5 BR
LD39020TPU185R 2 CR
LD39020ADTPU21R
2.1 Yes
0.5 A9
LD39020DTPU21R(1) 2 21
LD39020ADTPU25R
2.5 Yes
0.5 AA
LD39020DTPU25R 2 25
LD39020ADTPU27R(1)
2.7 Yes
0.5 AB
LD39020DTPU27R(1) 2 27
LD39020ADTPU28R
2.8 Yes
0.5 AC
LD39020DTPU28R(1) 2 28
LD39020ADTPU30R
3 Yes
0.5 AF
LD39020DTPU30R 2 30
LD39020ADTPU31R(1)
3.1 Yes
0.5 AG
LD39020DTPU31R 2 31
LD39020ATPU32R
3.2 No
0.5 BH
LD39020TPU32R 2 CH
LD39020ADTPU33R
3.3
Yes
0.5 AJ
LD39020DTPU33R 2 33
LD39020ATPU33R
No
0.5 BJ
LD39020TPU33R 2 CJ
LD39020ADTPU40R(1)
4 Yes
0.5 AL
LD39020DTPU40R 2 40
LD39020ADTPU47R(1)
4.7 Yes
0.5 AM
LD39020DTPU47R 2 47
1. Available on request.
LD39020
Order code
DS9956 - Rev 5 page 24/30
Table 11. SOT23-5L order code
Order code Output voltage (V) Auto-discharge Tolerance (%) Marking
LD39020ADM30R 3.0 Yes 0.5 AD30
LD39020
Order code
DS9956 - Rev 5 page 25/30
Revision history
Table 12. Document revision history
Date Revision Changes
04-Dec-2013 1 Initial release.
02-Apr-2014 2 Updated Table 10: "DFN4 1x1 order codes"..
05-Jun-2015 3
Added SOT23-5L package. Modified features and description in cover page.
Updated Section 7: "Pin configuration" and Table 3: "Thermal data". Added
Section 13.2: "SOT23-5L package information" and Section 13.3: "SOT23-5L
packing information".
Minor text changes.
03-Jul-2015 4
Updated package name from DFN1x1-4L to DFN4 1x1.
Updated note in Table 11: "SOT23-5L order code".
Minor text changes.
07-Jan-2019 5
Added Figure 31. DFN4 1x1 tape outline, Figure 32. DFN4 1x1 reel outline and
Figure 33. DFN4 1x1 orientation.
Updated Section 9 Order code.
LD39020
DS9956 - Rev 5 page 26/30
Contents
1Diagram ...........................................................................2
2Pin configuration ..................................................................3
3Typical application.................................................................4
4Maximum ratings ..................................................................5
5Electrical characteristics...........................................................6
6Application information............................................................9
6.1 Soft start function ..............................................................9
6.2 Output discharge function .......................................................9
6.3 Input and output capacitors ......................................................9
7Typical characteristics ............................................................10
8Package information..............................................................15
8.1 DFN4 1x1 package information ..................................................15
8.2 SOT23-5L package information..................................................21
8.3 SOT23-5L packing information ..................................................22
9Order codes ......................................................................24
Revision history .......................................................................26
Contents ..............................................................................27
List of tables ..........................................................................28
List of figures..........................................................................29
LD39020
Contents
DS9956 - Rev 5 page 27/30
List of tables
Table 1. Pin description......................................................................3
Table 2. Absolute maximum ratings .............................................................5
Table 3. Thermal data.......................................................................5
Table 4. ESD performance ...................................................................5
Table 5. Electrical characteristics for LD39020T, LD39020DT............................................6
Table 6. Electrical characteristics for LD39020AT, LD39020ADT..........................................7
Table 7. DFN4 1x1 mechanical data ............................................................ 17
Table 8. SOT23-5L package mechanical data ..................................................... 21
Table 9. SOT23-5L tape and reel mechanical data .................................................. 23
Table 10. DFN4 1x1 order code ................................................................ 24
Table 11. SOT23-5L order code................................................................ 25
Table 12. Document revision history ............................................................. 26
LD39020
List of tables
DS9956 - Rev 5 page 28/30
List of figures
Figure 2. Block diagram ....................................................................2
Figure 3. Pin connection (top view) .............................................................3
Figure 4. Typical application circuits ............................................................4
Figure 5. Output voltage vs. temperature (IOUT = 1 mA).............................................. 10
Figure 6. Output voltage vs. temperature (IOUT = 200 mA) ............................................ 10
Figure 7. Line regulation vs. temperature........................................................ 10
Figure 8. Load regulation vs. temperature ....................................................... 10
Figure 9. Quiescent current vs. temperature (IOUT = 0 mA) ........................................... 11
Figure 10. Quiescent current vs. temperature (IOUT = 200 mA).......................................... 11
Figure 11. Shutdown current vs. temperature...................................................... 11
Figure 12. Quiescent current vs. load current...................................................... 11
Figure 13. Quiescent current vs. input voltage ..................................................... 11
Figure 14. Dropout voltage vs. temperature ....................................................... 11
Figure 15. Supply voltage rejection vs. frequency ................................................... 12
Figure 16. Supply voltage rejection vs. input voltage ................................................. 12
Figure 17. Output noise spectral density ......................................................... 12
Figure 18. Stability area vs. (COUT, ESR) ........................................................ 12
Figure 19. Enable startup (VOUT = 1 V) .......................................................... 12
Figure 20. Enable startup (VOUT = 5 V) .......................................................... 12
Figure 21. Turn-on time (VOUT = 1 V) ........................................................... 13
Figure 22. Turn-off time (VOUT = 1 V) ........................................................... 13
Figure 23. Turn-on time (VOUT = 5 V) ........................................................... 13
Figure 24. Turn-off time (VOUT = 5 V) ........................................................... 13
Figure 25. Line transient (VOUT = 1 V)........................................................... 13
Figure 26. Line transient (VOUT = 5 V)........................................................... 13
Figure 27. Load transient (VOUT = 1 V) .......................................................... 14
Figure 28. Load transient (VOUT = 5 V) .......................................................... 14
Figure 29. DFN4 1x1 package outline ........................................................... 16
Figure 30. DFN4 1x1 recommended footprint...................................................... 18
Figure 31. DFN4 1x1 tape outline .............................................................. 19
Figure 32. DFN4 1x1 reel outline .............................................................. 19
Figure 33. DFN4 1x1 orientation .............................................................. 20
Figure 34. SOT23-5L package outline........................................................... 21
Figure 35. SOT23-5L recommended footprint ..................................................... 22
Figure 36. SOT23-5L tape and reel outline ....................................................... 23
LD39020
List of figures
DS9956 - Rev 5 page 29/30
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST
products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST
products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of
Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2019 STMicroelectronics – All rights reserved
LD39020
DS9956 - Rev 5 page 30/30
