DS26LS31MQML www.ti.com SNOSAM5B - AUGUST 2005 - REVISED APRIL 2013 DS26LS31MQML Quad High Speed Differential Line Driver Check for Samples: DS26LS31MQML FEATURES DESCRIPTION * * * The DS26LS31MQML is a quad differential line driver designed for digital data transmission over balanced lines. The DS26LS31MQML meets all the requirements of EIA Standard RS-422 and Federal Standard 1020. It is designed to provide unipolar differential drive to twisted-pair or parallel-wire transmission lines. 1 2 * * * * * Operation from Single 5V Supply Outputs Won't Load Line When VCC = 0V Four Line Drivers in One Package for Maximum Package Density Output Short-Circuit Protection Complementary Outputs Meets the Requirements of EIA Standard RS422 Pin Compatible with AM26LS31 Glitch Free Power Up/Down The circuit provides an enable and disable function common to all four drivers. The DS26LS31MQML features TRI-STATE outputs and logically ANDed complementary outputs. The inputs are all LS compatible and are all one unit load. The DS26LS31 features a power up/down protection circuit which keeps the output in a high impedance state (TRI-STATE) during power up or down preventing erroneous glitches on the transmission lines. Logic and Connection Diagrams 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2005-2013, Texas Instruments Incorporated DS26LS31MQML SNOSAM5B - AUGUST 2005 - REVISED APRIL 2013 www.ti.com Top View Figure 1. CDIP Package See Package Numbers NAJ0020A, NFE0016A, NAD0016A These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) Supply Voltage 7V Input Voltage 7V Output Voltage 5.5V -0.25 to 6V Output Voltage (Power OFF) Maximum Power Dissipation at 25C (2) NFE0016A Package 1400 mW NAJ0020A Package 1600 mW NAD0016A Package 850 mW Junction Temperature (TJ) +150C Thermal Resistance, Junction-to-Ambient JA NFE0016A Package 94C/W derate above +25C at 10.6 mW/C NAJ0020A Package 83C/W derate above +25C at 12 mW/C NAD0016A Package 163C/W derate above +25C at 6.1 mW/C Thermal Resistance, Junction-to-Case JC NFE0016A Package 16C/W NAJ0020A Package 19C/W NAD0016A Package 14C/W ESD Tolerance (1) (2) 2500V "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be specified. They are not meant to imply that the devices should be operated at these limits. The tables of "Electrical Characteristics" provide conditions for actual device operation. Derate CDIP = 11.5 mW/C, LCCC = 13mW/C, CLGA = 7.4mW/C above 25C. Recommended Operating Conditions Supply Voltage, VCC 4.5 V to 5.5 V -55C to +125C Temperature, TA 2 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: DS26LS31MQML DS26LS31MQML www.ti.com SNOSAM5B - AUGUST 2005 - REVISED APRIL 2013 Radiation Features DS26LS31MEFQML 300 Krads (Si) DS26LS31MJFQML 300 Krads (Si) DS26LS31MJFQMLV 300 Krads (Si) DS26LS31MWFQML 300 Krads (Si) DS26LS31MWFQMLV 300 Krads (Si) Quality Conformance Inspection MIL-STD-883, Method 5005 - Group A Subgroup Description Temp (C) 1 Static tests at +25 2 Static tests at +125 3 Static tests at -55 4 Dynamic tests at +25 5 Dynamic tests at +125 6 Dynamic tests at -55 7 Functional tests at +25 8A Functional tests at +125 8B Functional tests at -55 9 Switching tests at +25 10 Switching tests at +125 11 Switching tests at -55 DS26LS31M - SMD, QMLV & RH Electrical Characteristics DC Parameters The following conditions apply, unless otherwise specified. +V = 5V, VCM = 0V. (1) Parameter Test Conditions VIH Logical "1" Input Voltage VCC = 4.5V VIL Logical "0" Input Voltage VCC = 5.5V Notes Min See and (2) (3) 2 See (2) and .8 (3) (3) VOH Logical "1" Output Voltage VCC = 4.5V, IOH = -20mA See VOL Logical "0" Output Voltage VCC = 4.5V, IOL = 20mA See (3) (3) Max 2.5 Unit Subgroups V 1, 2, 3 V 1, 2, 3 V 1, 2, 3 .5 V 1, 2, 3 IIH Logical "1" Input Current VCC = 5.5V, VIN= 2.7V See -2.0 20 uA 1, 2, 3 IIL Logical "0" Input Current VCC = 5.5V, VIN = .4V See (3) 100 -360 uA 1, 2, 3 II Input Reverse Current VCC = 5.5V, VIN = 7V See (3) -.01 .1 mA 1, 2, 3 VCC = 5.5V, VO = .5V See (3) -20 uA 1, 2, 3 VCC = 5.5V, VO = 2.5V See (3) 20 uA 1, 2, 3 -1.5 V 1, 2, 3 -150 mA 1, 2, 3 80 mA 1, 2, 3 IO TRI-STATE Output Current VIC Input Clamp Voltage VCC = 4.5V, IIN = -18mA See (3) IOS Output Short Circuit Current VCC = 5.5V See (3) ICC Power Supply Current VCC = 5.5V, All Outputs Disabled or Active See (3) (1) (2) (3) -30 Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics. These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters are ensured only for the conditions as specified in MIL-STD 883, Method 1019, Condition A. Parameter tested go-no-go only. Subgroups 1, 2 and 9, 10: Power dissipation must be externally controlled at elevated temperatures. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: DS26LS31MQML 3 DS26LS31MQML SNOSAM5B - AUGUST 2005 - REVISED APRIL 2013 www.ti.com DS26LS31M - SMD, QMLV and RH Electrical Characteristics AC Parameters - Propagation Delay Time The following conditions apply, unless otherwise specified. VCC = 5V, VIN = 1.3V to VO = 1.3V, V (pulse) = 0 to 3V. (1) Parameter Test Conditions Notes tPLH Input to Output CL = 30 pF See (2) tPHL Input to Output CL = 30 pF See (2) tSkew Output to Output CL = 30 pF See (2) S2 Open, Enable, CL = 10 pF See (2) tPLZ tPHZ tPZL tPZH (1) (2) Min Enable to Output S2 Open, Enable, CL = 10 pF See (2) S1 Open, Enable, CL = 10 pF See (2) S1 Open, Enable, CL = 10 pF See (2) S2 Open, Enable, CL = 30 pF See (2) S2 Open, Enable, CL = 30 pF See (2) Enable to Output Enable to Output S1 Open, Enable, CL = 30 pF See (2) S1 Open, Enable, CL = 30 pF See (2) Enable to Output Subgroups Max Unit 20 ns 9 30 ns 10, 11 20 ns 9 30 ns 10, 11 6 ns 9 9 ns 10, 11 35 ns 9 53 ns 10, 11 35 ns 9 53 ns 10, 11 30 ns 9 45 ns 10, 11 30 ns 9 45 ns 10, 11 45 ns 9 68 ns 10, 11 45 ns 9 68 ns 10, 11 40 ns 9 60 ns 10, 11 40 ns 9 60 ns 10, 11 Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics. These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters are ensured only for the conditions as specified in MIL-STD 883, Method 1019, Condition A. Subgroups 1, 2 and 9, 10: Power dissipation must be externally controlled at elevated temperatures. DS26LS31M - SMD, QMLV and RH Electrical Characteristics DC Parameters - Drift Values The following conditions apply, unless otherwise specified. Delta calculations performed on QMLV only devices after burn-in and at Group B5. Parameter Test Conditions Notes Min Max Unit Subgroups VOL Output Low Voltage VCC = 4.5, IOL = 20 mA See (1) -50 50 mV 1 VOH Output High Voltage VCC = 4.5, IOH = -20 mA See (1) -250 250 mV 1 Power Supply Current VCC = 5.5, All outputs disabled or active See (1) -8 8 mA 1 Max Unit Subgroups V 1, 2, 3 V 1, 2, 3 V 1, 2, 3 ICC (1) Subgroups 1, 2 and 9, 10: Power dissipation must be externally controlled at elevated temperatures. DS26LS31M - 883 Electrical Characteristics DC Parameters Parameter VIH Logical "1" Input Voltage VIL Logical "0" Input Voltage VOH Logical "1" Output Voltage (1) (2) 4 Test Conditions Notes See (1) and (2) Min 2 See (1) and .8 (2) VCC = 4.5V, IOH = -20mA See (2) 2.5 Parameter tested go-no-go only. Subgroups 1, 2 and 9, 10: Power dissipation must be externally controlled at elevated temperatures. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: DS26LS31MQML DS26LS31MQML www.ti.com SNOSAM5B - AUGUST 2005 - REVISED APRIL 2013 DS26LS31M - 883 Electrical Characteristics DC Parameters (continued) Parameter Test Conditions Notes Min Max Unit Subgroups VOL Logical "0" Output Voltage VCC = 4.5V, IOL = 20mA See (2) .5 V 1, 2, 3 IIH Logical "1" Input Current VCC = 5.5V, VIN = 2.7V See (2) 20 uA 1, 2, 3 (2) IIL Logical "0" Input Current VCC = 5.5V, VIN = .4V See -200 uA 1, 2, 3 II Input Reverse Current VCC = 5.5V, VIN = 7V See (2) .1 mA 1, 2, 3 VCC = 5.5V, VO = .5V See (2) -20 uA 1, 2, 3 20 uA 1, 2, 3 -1.5 V 1, 2, 3 mA 1, 2, 3 IO TRI-STATE Output Current VCC = 5.5V, VO = 2.5V See VIC Input Clamp Voltage VCC = 4.5V, IIN = -18mA See (2) IOS (min) Output Short Circuit Current VCC = 5.5V See (2) Output Short Circuit Current VCC = 5.5V See (2) -150 mA 1, 2, 3 Power Supply Current VCC = 5.5V, All Outputs Disabled or Active See (2) 60 mA 1, 2, 3 IOS (max) ICC (2) -30 DS26LS31M - 883 Electrical Characteristics AC Parameters - Propagation Delay Time The following conditions apply, unless otherwise specified. VCC = 5V, CL = 50pF or equivalent impedance provided by diode load. Parameter tPLH Input to Output tPHL Input to Output tSkew Output to Output Test Conditions (2) See (1) and (2) See (1) and (2) Enable to Output S2 Open, /Enable S1 Open, Enable tPHZ Enable to Output S1 Open, /Enable S2 Open, Enable tPZL Enable to Output S2 Open, /Enable S1 Open, Enable tPZH Enable to Output S1 Open, /Enable (1) (2) Min See (1) and S2 Open, Enable tPLZ Notes See (1) and (2) See (1) and (2) See (1) and (2) See (1) and (2) See (1) and (2) See (1) and (2) See (1) and (2) See (1) and (2) Subgroups Max Unit 15 ns 9 30 ns 10, 11. 15 ns 9 30 ns 10, 11. 6 ns 9 9 ns 10, 11. 35 ns 9 53 ns 10, 11. 35 ns 9 53 ns 10, 11. 25 ns 9 45 ns 10, 11. 25 ns 9 45 ns 10, 11. 30 ns 9 68 ns 10, 11. 30 ns 9 68 ns 10, 11. 30 ns 9 60 ns 10, 11. 30 ns 9 60 ns 10, 11. Subgroups 1, 2 and 9, 10: Power dissipation must be externally controlled at elevated temperatures. Subgroup 10 and 11 specified but not tested. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: DS26LS31MQML 5 DS26LS31MQML SNOSAM5B - AUGUST 2005 - REVISED APRIL 2013 www.ti.com AC TEST CIRCUIT AND SWITCHING TIME WAVEFORMS S1 and S2 of load circuit are closed except where shown. Figure 2. AC Test Circuit f = 1 MHz, tr 15 ns, tf 6 ns Figure 3. Propagation Delays f = 1 MHz, tr 15 ns, tf 6 ns Figure 4. Enable and Disable Times TYPICAL APPLICATIONS Figure 5. Two-Wire Balanced System, RS-422 RT is optional although highly recommended to reduce reflection. 6 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: DS26LS31MQML DS26LS31MQML www.ti.com SNOSAM5B - AUGUST 2005 - REVISED APRIL 2013 Typical Performance Characteristics DS26LS31MQMLCN Unloaded IC vs Frequency vs TA DS26LS31MQML ICC vs VCC vs TA Figure 6. Figure 7. DS26LS31MQMLCN VOH vs IOH vs TA DS26LS31MQMLCN VOL vs IOL vs TA Figure 8. Figure 9. DS26LS31MQMLCN VOD vs IO vs TA Figure 10. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: DS26LS31MQML 7 DS26LS31MQML SNOSAM5B - AUGUST 2005 - REVISED APRIL 2013 www.ti.com REVISION HISTORY Date Released Revision 8/04/05 A 3/01/06 4/15/2013 8 Section New Release, Corporate format Ordering Info. Table, Absolute Ratings, Maximum Operating Conditions, New Radiation Section. Typos in QMLV & RH, 883 AC Electrical Characteristics Parameters Column Originator Changes R. Malone 2 MDS data sheets converted into a Corp. data sheet format. Following MDS data sheets will be Archived MDDS26LS31M-X-RH, Rev.2A0, MNDS26LS31M-X, Rev. 0A0 A1 R. Malone Added: Juction temp., Thermal Resistance JA and JC. Added a Radiation Section. Changed: Maximum Operating Conditions to Recommended Operating Conditions, Enable and Disable Time to Enable to Output. Revision A will be archived. B TIS Changed layout of National Data Sheet to TI format Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: DS26LS31MQML PACKAGE OPTION ADDENDUM www.ti.com 15-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) (3) Top-Side Markings (4) 5962-7802301VEA ACTIVE CDIP NFE 16 25 TBD Call TI Call TI -55 to 125 DS26LS31MJ-QMLV 5962-7802301VEA Q AM26LS31MW/883 ACTIVE CFP NAD 16 19 TBD Call TI Call TI -55 to 125 DS26LS31MW /883 Q ACO /883 Q >T DS26LS31ME-SMD ACTIVE LCCC NAJ 20 50 TBD Call TI Call TI -55 to 125 DS26LS31ME -SMD Q 5962-78023 01Q2A ACO 01Q2A >T DS26LS31MJ-QMLV ACTIVE CDIP NFE 16 25 TBD Call TI Call TI -55 to 125 DS26LS31MJ-QMLV 5962-7802301VEA Q DS26LS31MJ-SMD ACTIVE CDIP NFE 16 25 TBD Call TI Call TI -55 to 125 DS26LS31MJ-SMD 5962-7802301MEA Q DS26LS31MJ/883 ACTIVE CDIP NFE 16 25 TBD Call TI Call TI -55 to 125 DS26LS31MJ/883 Q DS26LS31MW/883 ACTIVE CFP NAD 16 19 TBD Call TI Call TI -55 to 125 DS26LS31MW /883 Q ACO /883 Q >T (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com (3) 15-Apr-2013 MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF DS26LS31MQML, DS26LS31MQML-SP : * Military: DS26LS31MQML * Space: DS26LS31MQML-SP NOTE: Qualified Version Definitions: * Military - QML certified for Military and Defense Applications * Space - Radiation tolerant, ceramic packaging and qualified for use in Space-based application Addendum-Page 2 MECHANICAL DATA NFE0016A J0016A J16A (REV L) www.ti.com MECHANICAL DATA NAJ0020A E20A (Rev F) www.ti.com MECHANICAL DATA NAD0016A W16A (Rev T) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated