Pin front view: Shell rotation
Contact
Arrangement W˚ X˚ Y˚ Z˚
14S-9 70 145 215 290
16-9 35 110 250 325
16-10 90 180 270 —
16-11 35 110 250 325
16S-1 80 — — 280
16S-8 — 170 265 —
18-1 70 145 215 290
18-4 35 110 250 325
18-5 80 110 250 280
18-8 70 — — 290
18-9 80 110 250 280
18-10 — 120 240 —
18-11 — 170 265 —
18-12 80 — — 280
18-20 90 180 270 —
18-22 70 145 215 290
20-3 70 145 215 290
20-4 45 110 250 —
20-7 80 110 250 280
20-19 90 180 270 —
20-27 35 110 250 325
Contact
Arrangement W˚ X˚ Y˚ Z˚
20-29 80 — — 280
20-33 35 110 256 325
22-2 70 145 215 290
22-14 80 — — 280
22-19 80 110 250 280
22-23 35 — 250 —
22-28 80 — — 280
24-2 80 — — 280
24-10 80 — — 280
24-20 80 110 250 280
24-28 80 110 250 280
28-10 80 110 250 280
28-11 80 110 250 280
28-12 90 180 270 —
28-15 80 110 250 280
28-16 80 110 250 280
28-21 80 110 250 280
36-5 — 120 240 —
36-7 80 110 250 280
36-8 80 110 250 280
36-10 80 125 235 280
Dimensions are shown in mm (inch)
Dimensions subject to change
www.ittcannon.com
Circular CA/MS A&B
Assembly Instructions
Step 3: Confirm insulator is fixed inside shell by
applying slight force on the engaging side of
the insulator. If properly installed, the insulator
can not be pushed out the rear of the shell. If
the insulator is displaced with this test, please
repeat steps 1 and 2.
Step 4: Complete assembly by adding coupling
nut and endbell. Please note that the coupling
nut is used on the plug side only.
*Note: During installation, ensure that all contacts remain fixed. If
during this process the contacts rotate out of position, separate
the 2 piece insulator and adjust accordingly.
Alternate Insert Positions
Step 2: After insulator is seated in shell, install
the snap ring on the rear of the connector.
Slightly compress ring and insert into recessed
area just above the insulator. If not completely
in place, manipulate the snap ring with finger
until visual or audible seating confirmation is
made. No tooling is required.
Step 1*: Remove tape from insulator. With the
insulator and shell positioned as shown above,
polarize insulator to desired position and place
inside shell using the internal keyway as
guide. Once inside the shell, the insulator
cannot rotate. However, until the snap ring is
applied in step 2, the insulator is not
captivated in the shell.
Unassembled connectors are supplied in kits,
an insulator kit and hardware kit. The insulator
kit includes a snap ring and insulator with
preloaded contacts. The hardware kit includes
the shell along with appropriate endbell
(except box mount receptacles) and coupling
nut (plug only).
Contact
Arrangement W˚ X˚ Y˚ Z˚
10SL-3 — — — —
10SL-4 — — — —
12S-3 70 145 215 290
14S-1 — — — —
14S-2 — 120 240 —
14S-5 — 110 — —
14S-6 — — — —
14S-7 90 180 270 —
4