P6SMB Series www.vishay.com Vishay General Semiconductor Surface Mount TRANSZORB(R) Transient Voltage Suppressors FEATURES * Low profile package * Ideal for automated placement * Glass passivated chip junction * Available in uni-directional and bi-directional * 600 W peak pulse power capability with a 10/1000 s waveform, repetitive rate (duty cycle): 0.01 % * Excellent clamping capability * Very fast response time * Low incremental surge resistance DO-214AA (SMB) * Meets MSL level 1, per J-STD-020, LF maximum peak of 260 C * AEC-Q101 qualified * Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 PRIMARY CHARACTERISTICS VWM 5.8 V to 459 V VBR (uni-directional) 6.8 V to 540 V VBR (bi-directional) 6.8 V to 220 V PPPM 600 W PD 5.0 W IFSM (uni-directional only) 100 A TJ max. 150 C Polarity Uni-directional, bi-directional Package DO-214AA (SMB) DEVICES FOR BI-DIRECTION APPLICATIONS For bi-directional devices use CA suffix (e.g. P6SMB10CA). Electrical characteristics apply in both directions. TYPICAL APPLICATIONS Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, and telecommunication. MECHANICAL DATA Case: DO-214AA (SMB) Molding compound meets UL 94 V-0 flammability rating Base P/N-E3 - RoHS compliant and commercial grade Base P/NHE3 - RoHS compliant and AEC-Q101 qualified Base P/NHE3_X - RoHS-compliant and AEC-Q101 qualified ("_X" denotes revision code e.g. A, B, .....) Terminals: Matte tin plated leads, solderable per J-STD-002 and JESD 22-B102 E3 suffix meets JESD 201 class 1A whisker test, HE3 suffix meets JESD 201 class 2 whisker test Polarity: For uni-directional types the band denotes cathode end, no marking on bi-directional types MAXIMUM RATINGS (TA = 25 C unless otherwise noted) PARAMETER SYMBOL VALUE UNIT Peak power dissipation with a 10/1000 s waveform (1)(2) (fig. 1) PPPM 600 W Peak pulse current with a 10/1000 s waveform (1) IPPM See next table A Power dissipation on infinite heatsink at TA = 50 C Peak forward surge current 8.3 ms single half sine-wave uni-directional only (2) Operating junction and storage temperature range PD 5.0 W IFSM 100 A TJ, TSTG - 65 to + 150 C Notes (1) Non-repetitive current pulse, per fig. 3 and derated above T = 25 C per fig. 2. A (2) Mounted on 0.2" x 0.2" (5.0 mm x 5.0 mm) copper pads to each terminal Revision: 14-Dec-12 Document Number: 88370 1 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 P6SMB Series www.vishay.com Vishay General Semiconductor ELECTRICAL CHARACTERISTICS (TA = 25 C unless otherwise noted) PART NUMBER DEVICE MARKING CODE UNI BI BREAKDOWN STAND-OFF VOLTAGE TEST VBR AT IT (1) CURRENT VOLTAGE VWM (V) IT (V) (mA) MIN. MAX. P6SMB6.8A 6V8A 6V8C 6.45 7.14 10 5.80 P6SMB7.5A 7V5A 7V5C 7.13 7.88 10 6.40 P6SMB8.2A 8V2A 8V2C 7.79 8.61 10 7.02 P6SMB9.1A 9V1A 9V1C 8.65 9.55 1.0 7.78 P6SMB10A 10A 10C 9.50 10.5 1.0 8.55 P6SMB11A 11A 11C 10.5 11.6 1.0 9.40 P6SMB12A 12A 12C 11.4 12.6 1.0 10.2 P6SMB13A 13A 13C 12.4 13.7 1.0 11.1 P6SMB15A 15A 15C 14.3 15.8 1.0 12.8 P6SMB16A 16A 16C 15.2 16.8 1.0 13.6 P6SMB18A 18A 18C 17.1 18.9 1.0 15.3 P6SMB20A 20A 20C 19.0 21.0 1.0 17.1 P6SMB22A 22A 22C 20.9 23.1 1.0 18.8 P6SMB24A 24A 24C 22.8 25.2 1.0 20.5 P6SMB27A 27A 27C 25.7 28.4 1.0 23.1 P6SMB30A 30A 30C 28.5 31.5 1.0 25.6 P6SMB33A 33A 33C 31.4 34.7 1.0 28.2 P6SMB36A 36A 36C 34.2 37.8 1.0 30.8 P6SMB39A 39A 39C 37.1 41.0 1.0 33.3 P6SMB43A 43A 43C 40.9 45.2 1.0 36.8 P6SMB47A 47A 47C 44.7 49.4 1.0 40.2 P6SMB51A 51A 51C 48.5 53.6 1.0 43.6 P6SMB56A 56A 56C 53.2 58.8 1.0 47.8 P6SMB62A 62A 62C 58.9 65.1 1.0 53.0 P6SMB68A 68A 68C 64.6 71.4 1.0 58.1 P6SMB75A 75A 75C 71.3 78.8 1.0 64.1 P6SMB82A 82A 82C 77.9 86.1 1.0 70.1 P6SMB91A 91A 91C 86.5 95.5 1.0 77.8 P6SMB100A 100A 100C 95.0 105 1.0 85.5 P6SMB110A 110A 110C 105 116 1.0 94.0 P6SMB120A 120A 120C 114 126 1.0 102 P6SMB130A 130A 130C 124 137 1.0 111 P6SMB150A 150A 150C 143 158 1.0 128 P6SMB160A 160A 160C 152 168 1.0 136 P6SMB170A 170A 170C 162 179 1.0 145 P6SMB180A 180A 180C 171 189 1.0 154 P6SMB200A 200A 200C 190 210 1.0 171 P6SMB220A 220A 220C 209 231 1.0 185 P6SMB250A 250A 237 263 1.0 214 P6SMB300A 300A 285 315 1.0 256 P6SMB350A 350A 333 368 1.0 300 P6SMB400A 400A 380 420 1.0 342 P6SMB440A 440A 418 462 1.0 376 P6SMB480A 480A 456 504 1.0 408 P6SMB510A 510A 485 535 1.0 434 P6SMB540A 540A 513 567 1.0 459 Notes (1) Pulse test: t 50 ms p (2) Surge current waveform per fig. 3 and derate per fig. 2 (3) For bi-directional types with V WM of 10 V and less, the ID limit is doubled (4) All terms and symbols are consistent with ANSI/IEEE CA62.35 (5) V = 3 V at I = 50 A (uni-directional only) F F Revision: 14-Dec-12 MAXIMUM REVERSE LEAKAGE AT VWM ID (3) (A) 1000 500 200 50 10 5.0 5.0 5.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 MAXIMUM PEAK PULSE CURRENT IPPM (2) (A) 57.1 53.1 49.6 44.8 41.4 38.5 35.9 33.0 28.3 26.7 23.8 21.7 19.6 18.1 16.0 14.5 13.1 12.0 11.1 10.1 9.3 8.6 7.8 7.1 6.5 5.8 5.3 4.8 4.4 3.9 3.6 3.4 2.9 2.7 2.6 2.4 2.2 1.8 1.74 1.45 1.24 1.10 1.00 0.91 0.86 0.81 MAXIMUM MAXIMUM CLAMPING TEMPERATURE COEFFICIENT VOLTAGE OF VBR AT IPPM VC (V) (%/C) 10.5 11.3 12.1 13.4 14.5 15.6 16.7 18.2 21.2 22.5 25.2 27.7 30.6 33.2 37.5 41.4 45.7 49.9 53.9 59.3 64.8 70.1 77.0 85.0 92.0 103 113 125 137 152 165 179 207 219 234 246 274 328 344 414 482 548 602 658 698 740 0.057 0.061 0.065 0.068 0.073 0.075 0.078 0.081 0.084 0.086 0.088 0.090 0.092 0.094 0.096 0.097 0.098 0.099 0.100 0.101 0.101 0.102 0.103 0.104 0.104 0.105 0.105 0.106 0.106 0.107 0.107 0.107 0.108 0.108 0.108 0.108 0.108 0.108 0.110 0.110 0.110 0.110 0.110 0.110 0.110 0.110 Document Number: 88370 2 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 P6SMB Series www.vishay.com Vishay General Semiconductor THERMAL CHARACTERISTICS (TA = 25 C unless otherwise noted) PARAMETER SYMBOL VALUE Typical thermal resistance, junction to ambient air (1) RJA 100 Typical thermal resistance, junction to lead RJL 20 UNIT C/ W Note (1) Mounted on minimum recommended pad layout ORDERING INFORMATION (Example) PREFERRED P/N VOLTAGE RANGE (V) UNIT WEIGHT (g) UNI - BI - 0.096 6.8 to 540 P6SMB6.8A-E3/52 P6SMB6.8A-E3/5B PACKAGE CODE BASE QUANTITY DELIVERY MODE 6.8 to 220 52 750 7" diameter plastic tape and reel 5B 3200 13" diameter plastic tape and reel 0.096 6.8 to 540 6.8 to 220 (1) 0.096 6.8 to 540 6.8 to 220 52 750 7" diameter plastic tape and reel P6SMB6.8AHE3/5B (1) 0.096 6.8 to 540 6.8 to 220 5B 3200 13" diameter plastic tape and reel P6SMB250AHE3_A/H (1) 0.096 250 to 540 - H 750 7" diameter plastic tape and reel 0.096 250 to 540 - I 3200 13" diameter plastic tape and reel P6SMB6.8AHE3/52 P6SMB250AHE3_A/I (1) Note AEC-Q101 qualified (1) RATINGS AND CHARACTERISTICS CURVES (TA = 25 C unless otherwise noted) Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage, % PPPM - Peak Pulse Power (kW) 100 10 1 0.2 x 0.2" (5.0 x 5.0 mm) Copper Pad Areas 0.1 0.1 s 1.0 s 10 s 100 s 1.0 ms 10 ms 100 75 50 25 0 0 25 50 75 100 125 150 175 200 td - Pulse Width (s) TJ - Initial Temperature (C) Fig. 1 - Peak Pulse Power Rating Curve Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature Revision: 14-Dec-12 Document Number: 88370 3 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 P6SMB Series www.vishay.com tr = 10 s Peak Value IPPM 100 200 TJ = 25 C Pulse Width (td) is defined as the Point where the Peak Current decays to 50 % of IPPM Peak Forward Surge Current (A) IPPM - Peak Pulse Current, % IRSM 150 Vishay General Semiconductor Half Value - IPP IPPM 2 50 10/1000 s Waveform as defined by R.E.A. 8.3 ms Single Half Sine-Wave Uni-Directional Only 100 td 10 0 1.0 0 3.0 2.0 4.0 t - Time (ms) 1 10 100 Number of Cycles at 60 Hz Fig. 3 - Pulse Waveform Fig. 6 - Maximum Non-Repetitive Peak Forward Surge Current CJ - Junction Capacitance (pF) 6000 Measured at Zero Bias 1000 VR, Measured at Stand-Off Voltage VWM 100 TJ = 25 C f = 1.0 MHz Vsig = 50 mVp-p Uni-Directional Bi-Directional 10 1 10 100 200 VWM - Reverse Stand-Off Voltage (V) Fig. 4 - Typical Junction Capacitance Transient Thermal Impedance (C/W) 100 10 1.0 0.1 0.001 0.01 0.1 1 10 100 1000 tp - Pulse Duration (s) Fig. 5 - Typical Transient Thermal Impedance Revision: 14-Dec-12 Document Number: 88370 4 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 P6SMB Series www.vishay.com Vishay General Semiconductor PACKAGE OUTLINE DIMENSIONS in inches (millimeters) DO-214AA (SMB) Mounting Pad Layout Cathode Band 0.085 (2.159) MAX. 0.155 (3.94) 0.130 (3.30) 0.086 (2.20) 0.077 (1.95) 0.086 (2.18) MIN. 0.180 (4.57) 0.160 (4.06) 0.012 (0.305) 0.006 (0.152) 0.060 (1.52) MIN. 0.220 REF. 0.096 (2.44) 0.084 (2.13) 0.060 (1.52) 0.030 (0.76) 0.008 (0.2) 0 (0) 0.220 (5.59) 0.205 (5.21) Revision: 14-Dec-12 Document Number: 88370 5 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000