Datasheet Serial EEPROM series Standard EEPROM I2C BUS EEPROM (2-Wire) BR24G04-3A General Description BR24G04-3A is a serial EEPROM of I2C BUS interface method Features All controls available by 2 ports of serial clock(SCL) and serial data(SDA) Other devices than EEPROM can be connected to the same port, saving microcontroller port 1.6V to 5.5V single power source action most suitable for battery use 1MHz action is possible (1.7V to 5.5V) Up to 16 bytes in page write mode Self-timed programming cycle Low current consumption Prevention of write mistake Write (write protect) function added Prevention of write mistake at low voltage More than 1 million write cycles More than 40 years data retention Noise filter built in SCL / SDA terminal Initial delivery state FFh Packages W(Typ.) x D(Typ.)x H(Max.) DIP-T8 TSSOP-B8J 9.30mm x 6.50mm x 7.10mm 3.00mm x 4.90mm x 1.10mm MSOP8 SOP8 5.00mm x 6.20mm x 1.71mm 2.90mm x 4.00mm x 0.90mm SOP-J8 VSON008X2030 4.90mm x 6.00mm x 1.65mm 2.00mm x 3.00mm x 0.60mm TSSOP-B8 3.00mm x 6.40mm x 1.20mm Figure 1. BR24G04-3A Capacity 4Kbit Bit Format 512x8 Type Power Source Voltage Package BR24G04-3A DIP-T8 BR24G04F-3A SOP8 BR24G04FJ-3A SOP-J8 BR24G04FVT-3A 1.6V to 5.5V TSSOP-B8 BR24G04FVJ-3A TSSOP-B8J BR24G04FVM-3A MSOP8 BR24G04NUX-3A VSON008X2030 Product structureSilicon monolithic integrated circuit .www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211114001 This product is not designed protection against radioactive rays 1/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Absolute Maximum Ratings (Ta=25) Parameter Supply Voltage Power Dissipation Symbol Ratings Unit VCC -0.3 to +6.5 V Pd Remarks 450 (SOP8) When using at Ta=25 or higher 4.5mW to be reduced per 1. 450 (SOP-J8) When using at Ta=25 or higher 4.5mW to be reduced per 1. 330 (TSSOP-B8) When using at Ta=25 or higher 3.3mW to be reduced per 1. 310 (TSSOP-B8J) mW When using at Ta=25 or higher 3.1mW to be reduced per 1. 310 (MSOP8) When using at Ta=25 or higher 3.1mW to be reduced per 1. 300 (VSON008X2030) When using at Ta=25 or higher 3.0mW to be reduced per 1. 800 (DIP-T8) When using at Ta=25 or higher 8.0mW to be reduced per 1. Storage Temperature Tstg 65 to +150 Operation Temperature Topr 40 to +85 -0.3 to Vcc+1.0 V The Max value of input voltage / output voltage is not over 6.5V. When the pulse width is 50ns or less, the Min value of input voltage / output voltage is not under -0.8V. Junction Temperature Tjmax 150 Junction temperature at the storage condition Electrostatic discharge voltage (human body model) VESD -4000 to +4000 V Input Voltage / Output Voltage Memory Cell Characteristics (Ta=25, Vcc=1.6V to 5.5V) Limits Parameter Min. Typ. 1,000,000 Write cycles *1 40 Data retention *1 Max Unit Times Years *1Not 100% TESTED Recommended Operating Ratings Parameter Symbol Supply voltage Vcc Input voltage VIN Ratings 1.6 to 5.5 0 to Vcc Unit V DC Characteristics (Unless otherwise specified, Ta=-40 to +85, Vcc =1.6 to 5.5V) Limits Parameter Symbol Unit Min. Typ. Max. Vcc+1.0 V 1.7VVcc5.5V 0.3Vcc V 1.7VVcc5.5V Vcc+1.0 V 1.6VVcc1.7V 0.2Vcc V 1.6VVcc1.7V 0.4 V IOL=3.0mA, 2.5VVcc5.5V (SDA) 0.2 V IOL=0.7mA, 1.6VVcc2.5V (SDA) ILI 1 1 A VIN=0 to Vcc ILO 1 1 A VOUT=0 to Vcc (SDA) ICC1 2.0 ICC2 - - 2.0 ISB 2.0 Input High Voltage1 VIH1 Input Low Voltage1 VIL1 Input High Voltage2 VIH2 Input Low Voltage2 VIL2 Output Low Voltage1 VOL1 Output Low Voltage2 VOL2 Input Leakage Current Output Leakage Current Supply Current (Write) Supply Current (Read) 0.7Vcc 0.3*1 0.8Vcc 0.3*1 mA Standby Current Conditions A Vcc=5.5V, fSCL=1MHz, tWR=5ms, Byte write, Page write Vcc=5.5V, fSCL=1MHz Random read, current read, sequential read Vcc=5.5V, SDA, SCL=Vcc A0, A1, A2=GND,WP=GND *1 When the pulse width is 50ns or less, it is -0.8V. www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 2/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A AC Characteristics (Unless otherwise specified, Ta=40 to +85) Parameter Symbol Limits (1.6VVcc1.7V) Min. Typ. Max. 1000 kHz - - 0.3 s 1.2 - - 0.5 s fSCL Data Clock "HIGH" Period tHIGH 0.6 tLOW SDA, SCL (INPUT) Rise Time *1 SDA, SCL (INPUT) Fall Time *1 SDA (OUTPUT) Fall Time *1 Unit 400 Clock Frequency Data Clock "LOW" Period Limits (1.7VVcc5.5V) Min. Typ. Max. - - tR - - 1 0.12 s tF1 - - 1 0.12 s tF2 - - 0.12 0.12 s s s Start Condition Hold Time tHD:STA 0.6 - - 0.25 Start Condition Setup Time tSU:STA 0.6 - - 0.20 Input Data Hold Time tHD:DAT 0 - - 0 ns Input Data Setup Time tSU:DAT 100 - - 50 ns Output Data Delay Time tPD 0.1 - 0.9 0.05 0.45 s Output Data Hold Time tDH 0.1 - - 0.05 s tSU:STO 0.6 - - 0.25 s Bus Free Time tBUF 1.2 - - 0.5 s Write Cycle Time tWR - - 5 5 ms tI - - 0.05 0.05 s s Stop Condition Setup Time Noise Spike Width (SDA, SCL) WP Hold Time tHD:WP 1.0 - - 1.0 WP Setup Time tSU:WP 0.1 - - 0.1 s WP High Period tHIGH:WP 1.0 - - 1.0 s *1 Not 100% tested AC Characteristics Condition Parameter Symbol Condition Unit Load Capacitance CL 100 pF SDA, SCL (INPUT) Rise Time tR 20 ns SDA, SCL (INPUT) Fall Time Input Data Level Input/Output Data Timing Reference Level www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 tF1 20 ns VIL1/VIH1 0.2Vcc/0.8Vcc V - 0.3Vcc/0.7Vcc V 3/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Serial Input / Output timing tR SCL tF1 70% 70% 70% 70% 30% 30% tHD:DAT tSU:DAT 70% 70% 30% 30% tLOW tHD:STA 70% tHIGH 70% 70% 30% 30% SDA () (INPUT) tDH tPD tBUF 70% 70% SDA 30% () (OUTPUT) 30% 30% Input read at the rise edge of SCL Data output in sync with the fall of SCL tF2 Figure 2-(a). Serial input / output timing 70% 70% 70% tSU:STA tHD:STA tSU:STO 70% 30% 30% STOP CONDITION START CONDITION Figure 2-(b). Start-stop bit timing D0 70% 70% ACK write data (n-th address) tWR STOP CONDITION START CONDITION Figure 2-(c). Write cycle timing 70% DATA(n) DATA(1) D0 D1 70% ACK ACK tWR 30% 30% tSU:WP tHD:WP STOP CONDITION Figure 2-(d). WP timing at write execution DATA(n) DATA(1) D1 D0 ACK ACK tWR tHIGH:WP 70% 70% 70% Figure 2-(e). WP timing at write cancel www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 4/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Block Diagram *A0 1 4Kbit EEPROM array 8 Vcc 7 WP 6 SCL 5 SDA 8bit A1 2 Address decoder Word address register 9bit START A2 3 Data register STOP Control circuit ACK GND 4 Power source voltage detection High voltage generating circuit * A0=Don't use Figure 3. Block diagram Pin Configuration A0 1 A1 2 8 Vcc 7 WP BR24G04-3A A2 3 6 SCL GND 4 5 SDA Pin Descriptions Terminal Name Input/ Output Function A0 Input Don't use*1 A1 Input Slave address setting*2 A2 Input Slave address setting*2 GND Reference voltage of all input / output, 0V SDA Input/ output Serial data input serial data output SCL Input Serial clock input WP Input Write protect terminal Vcc Connect the power source. *1 Pins not used as device address may be set to any of `H','L', and `Hi-Z'. *2 A1 and A2 are not allowed to use as open. www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 5/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Typical Performance Curves (The following values are Typ. ones) 6 5 5 Ta=-40 Ta= 25 Ta= 85 4 INPUT LOW VOLTAGE: VIL1(V) INPUT HIGH VOLTAGE: VIH1(V) 6 3 SPEC 2 3 2 1 1 0 0 0 1 2 3 4 5 Ta=-40 Ta= 25 Ta= 85 4 SPEC 0 6 1 3 4 5 6 SUPPLY VOLTAGE: Vcc(v) SUPPLY VOLTAGE: Vcc(v) Figure 5. Input Low Voltage1,2 VIL1,2 (A1, A2, SCL, SDA, WP) Figure 4. Input High Voltage1,2 VIH1,2 (A1, A2, SCL, SDA, WP) 1 1 Ta=-40 Ta= 25 Ta= 85 0.8 OUTPUT LOW VOLTAGE: VOL2(V) OUTPUT LOW VOLTAGE: VOL1(V) 2 0.6 SPEC 0.4 0.2 Ta=-40 Ta= 25 Ta= 85 0.8 0.6 0.4 SPEC 0.2 0 0 0 1 2 3 4 5 0 6 1 2 3 4 5 L OUTPUT CURRENT: IOL(mA) L OUTPUT CURRENT: IOL(mA) Figure 6. Output Low Voltage1 VOL1 (Vcc=2.5V) Figure 7. Output Low Voltage2 VOL2 (Vcc=1.6V) www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 6/33 6 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Typical Performance CurvesContinued 1.2 OUTPUT LEAKAGE CURRENT: ILO(A) INPUT LEAKAGE CURRENT: ILI (A) 1.2 SPEC 1 Ta=-40 Ta= 25 Ta= 85 0.8 0.6 0.4 0.2 0 SPEC 1 0.8 Ta=-40 Ta= 25 Ta= 85 0.6 0.4 0.2 0 0 1 2 3 4 5 6 0 1 3 4 5 6 SUPPLY VOLTAGE: Vcc(v) SUPPLY VOLTAGE: Vcc(v) Figure 8. Input Leakage Current ILI (A1, A2, SCL, WP) Figure 9. Output Leakage Current ILO (SDA) 2.5 SUPPLY CURRENT (READ) : Icc2(mA) 2.5 SUPPLY CURRENT (WRITE) : Icc1(mA) 2 SPEC 2 1.5 Ta=-40 Ta= 25 Ta= 85 1 0.5 SPEC 2 Ta=-40 Ta= 25 Ta= 85 1.5 1 0.5 0 0 0 1 2 3 4 5 0 6 2 3 4 5 6 SUPPLY VOLTAGE: Vcc(v) SUPPLY VOLTAGE: Vcc(v) Figure 10. Supply Current (WRITE) ICC1 (fscl=1MHz) www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 1 Figure 11. Supply Current (READ) ICC2 (fscl=1MHz) 7/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Typical Performance CurvesContinued 10000 2.5 SCL FREQUENCY: fscl(kHz) STANDBY CURRENT: I SB (A) SPEC 2 Ta=-40 Ta= 25 Ta= 85 1.5 1 0.5 1000 SPEC 100 Ta=-40 Ta= 25 Ta= 85 10 1 0.1 0 0 1 2 3 4 5 0 6 1 2 3 4 5 6 SUPPLY VOLTAGE: Vcc(v) SUPPLY VOLTAGE: Vcc(v) Figure 12. Standby Current ISB Figure 13. Clock Frequency fSCL 0.6 0.4 SPEC 0.5 LOW (s) Ta=-40 Ta= 25 Ta= 85 0.2 DATA CLK L TIME : t DATA CLK H TIME : t HIGH (s) SPEC 0.3 0.1 Ta=-40 Ta= 25 Ta= 85 0.4 0.3 0.2 0.1 0 0 0 1 2 3 4 5 0 6 2 3 4 5 6 SUPPLY VOLTAGE: Vcc(v) SUPPLY VOLTAGE: Vcc(v) Figure 15. Data Clock Low Period tLOW Figure 14. Data Clock High Period tHIGH www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 1 8/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Typical Performance CurvesContinued 0.3 HD:STA (s) 0.1 SPEC START CONDITION HOLD TIME: t F2 (s) 0.12 SDA (OUTPUT) FALL TIME: t 0.14 Ta=-40 Ta= 25 Ta= 85 0.08 0.06 0.04 0.02 0 SPEC 0.25 0.2 Ta=-40 Ta= 25 Ta= 85 0.15 0.1 0.05 0 0 1 2 3 4 5 6 0 1 SUPPLY VOLTAGE: Vcc(v) 4 5 6 Figure 17. Start Condition Hold Time tHD:STA 0.3 50 SPEC HD:DAT (ns) 0.25 0.2 Ta=-40 Ta= 25 Ta= 85 0.15 INPUT DATA HOLD TIME: t SU:STA (s) 3 SUPPLY VOLTAGE: Vcc(v) Figure 16. SDA (OUTPUT) Fall Time tF2 START CONDITION SETUP TIME: t 2 0.1 0.05 0 SPEC 0 -50 Ta=-40 Ta= 25 Ta= 85 -100 -150 -0.05 0 1 2 3 4 5 6 0 1 2 3 4 5 SUPPLY VOLTAGE: Vcc(v) SUPPLY VOLTAGE: Vcc(v) Figure 18. Start Condition Setup Time tSU:STA Figure 19. Input Data Hold Time tHD:DAT(HIGH) www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 9/33 6 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Typical Performance CurvesContinued 60 SU:DAT (ns) SPEC 0 INPUT DATA SET UP TIME: t INPUT DATA HOLD TIME: t HD:DAT (ns) 50 -50 Ta=-40 Ta= 25 Ta= 85 -100 -150 SPEC 50 Ta=-40 Ta= 25 Ta= 85 40 30 20 10 0 0 1 2 3 4 5 6 0 1 SUPPLY VOLTAGE: Vcc(v) 2 3 4 5 6 SUPPLY VOLTAGE: Vcc(v) Figure 20. Input Data Hold Time tHD:DAT(LOW) Figure 21. Input Data Setup Time tSU:DAT(HIGH) 0.5 60 PD (s) 50 OUTPUT DATA DELAY TIME: t INPUT DATA SET UP TIME: t SU:DAT (ns) SPEC SPEC 40 Ta=-40 Ta= 25 Ta= 85 30 20 10 0.4 0.3 0.2 Ta=-40 Ta= 25 Ta= 85 0.1 SPEC 0 0 0 1 2 3 4 5 6 0 SUPPLY VOLTAGE: Vcc(v) 2 3 4 5 6 SUPPLY VOLTAGE: Vcc(v) Figure 22. Input Data Setup Time tSU:DAT(LOW) www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 1 10/33 Figure 23. `L' Output Data Delay Time tPD0 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Typical Performance CurvesContinued 0.5 SU:STO (s) 0.3 0.4 STOP CONDITION SET UP TIME: t OUTPUT DATA DELAY TIME: t PD (s) SPEC 0.3 0.2 Ta=-40 Ta= 25 Ta= 85 0.1 SPEC SPEC 0.25 0.2 0.15 0.1 Ta=-40 Ta= 25 Ta= 85 0.05 0 0 0 1 2 3 4 5 0 6 1 2 0.6 SPEC 5 INTERNAL WRITING CYCLE TIME: t W R(ms) BUF (s) 6 6 SPEC BUS OPEN TIME BEFORE TRANSMISSION: t 5 Figure 25. Stop Condition Setup Time tSU:STO Figure 24. `H' Output Data Delay Time tPD1 0.4 4 SUPPLY VOLTAGE: Vcc(v) SUPPLY VOLTAGE: Vcc(v) 0.5 3 Ta=-40 Ta= 25 Ta= 85 0.3 0.2 4 3 2 0.1 1 0 0 0 1 2 3 4 5 0 6 1 2 3 4 5 6 SUPPLY VOLTAGE: Vcc(v) SUPPLY VOLTAGE: Vcc(v) Figure 26. BUS Free Time tBUF www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 Ta=-40 Ta= 25 Ta= 85 Figure 27. Write Cycle Time tWR 11/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A 0.3 0.3 0.25 0.25 NOISE REDUCTION EFECTIVE TIME: t I(SCL L)(s) NOISE REDUCTION EFECTIVE TIME: t I(SCL H)(s) Typical Performance CurvesContinued Ta=-40 Ta= 25 Ta= 85 0.2 0.15 0.1 0.05 SPEC Ta=-40 Ta= 25 Ta= 85 0.2 0.15 0.1 0.05 SPEC 0 0 0 1 2 3 4 5 0 6 1 SUPPLY VOLTAGE: Vcc(v) 4 5 6 Figure 29. Noise Spike Width tI (SCL L) 0.3 0.3 0.25 0.25 NOISE REDUCTION EFECTIVE TIME: t I(SDA L)(s) NOISE REDUCTION EFECTIVE TIME: t I(SDA H)(s) 3 SUPPLY VOLTAGE: Vcc(v) Figure 28. Noise Spike Width tI (SCL H) Ta=-40 Ta= 25 Ta= 85 0.2 2 0.15 0.1 0.05 Ta=-40 Ta= 25 Ta= 85 0.2 0.15 0.1 0.05 SPEC SPEC 0 0 0 1 2 3 4 5 0 6 2 3 4 5 6 SUPPLY VOLTAGE: Vcc(v) SUPPLY VOLTAGE: Vcc(v) Figure 31. Noise Spike Width tI (SDA L) Figure 30. Noise Spike Width tI (SDA H) www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 1 12/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Typical Performance CurvesContinued 1.2 0.2 SU:W P (s) 0.8 WP DATA SET UP TIME: t WP DATA HOLD TIME: t HD:W P(s) SPEC 1 Ta=-40 Ta= 25 Ta= 85 0.6 0.4 0.2 0 SPEC 0.1 Ta=-40 Ta= 25 Ta= 85 0 -0.1 -0.2 -0.3 0 1 2 3 4 5 6 0 1 2 3 4 5 SUPPLY VOLTAGE: Vcc(v) SUPPLY VOLTAGE: Vcc(v) Figure 32. WP Hold Time tHD:WP Figure 33. WP Setup Time tSU:WP 6 1.2 WP EFECTIVE TIME: t HIGH:W P ( s) SPEC 1 0.8 Ta=-40 Ta= 25 Ta= 85 0.6 0.4 0.2 0 0 1 2 3 4 5 6 SUPPLY VOLTAGE: Vcc(v) Figure 34. WP High Time tHIGH:WP www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 13/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Timing Chart I2C BUS data communication I2C BUS data communication starts by start condition input, and ends by stop condition input. Data is always 8bit long, and acknowledge is always required after each byte. I2C BUS carries out data transmission with plural devices connected by 2 communication lines of serial data (SDA) and serial clock (SCL). Among devices, there are "master" that generates clock and control communication start and end, and "slave" that is controlled by address peculiar to devices. EEPROM becomes "slave". And the device that outputs data to bus during data communication is called "transmitter", and the device that receives data is called "receiver". SDA SCL 1-7 S START ADDRESS condition 8 9 R/W ACK 1-7 8 1-7 9 DATA ACK 8 DATA 9 ACK P STOP condition Figure 35. Data transfer timing Start condition (Start bit recognition) Before executing each command, start condition (start bit) where SDA goes from 'HIGH' down to 'LOW' when SCL is 'HIGH' is necessary. This IC always detects whether SDA and SCL are in start condition (start bit) or not, therefore, unless this confdition is satisfied, any command is executed. Stop condition (stop bit recongnition) Each command can be ended by SDA rising from 'LOW' to 'HIGH' when stop condition (stop bit), namely, SCL is 'HIGH' Acknowledge (ACK) signal This acknowledge (ACK) signal is a software rule to show whether data transfer has been made normally or not. In master and slave, the device (-COM at slave address input of write command, read command, and this IC at data output of read command) at the transmitter (sending) side releases the bus after output of 8bit data. The device (this IC at slave address input of write command, read command, and -COM at data output of read command) at the receiver (receiving) side sets SDA 'LOW' during 9 clock cycles, and outputs acknowledge signal (ACK signal) showing that it has received the 8bit data. This IC, after recognizing start condition and slave address (8bit), outputs acknowledge signal (ACK signal) 'LOW'. Each write action outputs acknowledge signal (ACK signal) 'LOW', at receiving 8bit data (word address and write data). Each read action outputs 8bit data (read data), and detects acknowledge signal (ACK signal) 'LOW'. When acknowledge signal (ACK signal) is detected, and stop condition is not sent from the master (-COM) side, this IC continues data output. When acknowledge signal (ACK signal) is not detected, this IC stops data transfer, and recognizes stop cindition (stop bit), and ends read action. And this IC gets in status. Device addressing Output slave address after start condition from master. The significant 4 bits of slave address are used for recognizing a device type. The device code of this IC is fixed to '1010'. Next slave addresses (A1,A2--- device address) are for selecting devices, and plural ones can be used on a same bus according to the number of device addresses. The most insignificant bit (R/W --- READ / WRITE) of slave address is used for designating write or read action, and is as shown below. Setting R / Setting R / W W to 0 ------- write (setting 0 to word address setting of random read) to 1 ------- read Type BR24G04-3A Maximum number of Connected buses Slave address 1 0 1 0 A2 A1 P0 R/W 4 P0 is page select bits. www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 14/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Write Command Write cycle Arbitrary data is written to EEPROM. When to write only 1 byte, byte write is normally used, and when to write continuous data of 2 bytes or more, simultaneous write is possible by page write cycle. Up to 16 arbitrary bytes can be written. S T A R T SDA LINE W R I T E SLAVE ADDRESS WORD ADDRESS WA 7 1 0 1 0 A2 A1 P0 S T O P DATA WA 0 D0 D7 A C K R A / C W K A C K Figure 36. Byte write cycle S T A R T SDA LINE SLAVE ADDRESS W R I T E WORD ADDRESS(n) WA 7 1 0 1 0 A2 A1 P0 R A / C W K DATA(n) WA 0 D7 A C K S T O P DATA(n+15) D0 D0 A C K A C K Figure 37. Page write cycle During internal write execution, all input commands are ignored, therefore ACK is not sent back. Data is written to the address designated by word address (n-th address) By issuing stop bit after 8bit data input, write to memory cell inside starts. When internal write is started, command is not accepted for tWR (5ms at maximum). By page write cycle, data up to 16 bytes can be written in bulk. And when data of the maximum bytes or higher is sent, data from the first byte is overwritten. (Refer to "Internal address increment") As for page write command of BR24G04-3A after page select bit 'P0' of slave address are designated arbitrarily, by continuing data input of 2 bytes or more, the address of insignificant 4 bits is incremented internally, and data up to 16 bytes can be written. www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 15/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Notes on write cycle continuous input The maximum page numbers of BR24G04-3A are 16 bytes. Any bytes below these can be written. 1 page=16bytes, but the page write cycle time is 5ms at maximum for 16byte bulk write. It does not stand 5ms at maximum x 16byte=80ms(Max.) Internal address increment Page write mode 0Eh 0 0 0 WA7 WA4 WA3 WA2 WA1 WA0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 0 0 1 0 Increment For example, when it is started from address 0Eh, therefore, increment is made as below, 0Eh0Fh00h01h which please note. 0Eh0E in hexadecimal, therefore, 00001110 becomes a binary number. Significant bit is fixed. No digit up Write protect (WP) terminal Write protect (WP) function When WP terminal is set Vcc (H level), data rewrite of all addresses is prohibited. When it is set GND (L level), data rewrite of all address is enabled. Be sure to connect this terminal to Vcc or GND, or control it to H level or L level. Do not use it open. In the case of use it as an ROM, it is recommended to connect it to pull up or Vcc. At extremely low voltage at power ON / OFF, by setting the WP terminal 'H', mistake write can be prevented. www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 16/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Read Command Read cycle Data of EEPROM is read. In read cycle, there are random read cycle and current read cycle. Random read cycle is a command to read data by designating address, and is used generally. Current read cycle is a command to read data of internal address register without designating address, and is used when to verify just after write cycle. In both the read cycles, sequential read cycle is available, and the next address data can be read in succession. S T A R T SD A LINE S LA VE A DDRE SS W R I T E S T A R T W O RD ADD RES S(n) WA 0 WA 7 1 0 1 0 A2A1P0 R A / C W K R E A D SLA VE A DDRE SS DA TA (n) 1 0 1 0 A 2 A1P0 A C K S T O P D7 D0 A C K R A / C W K Figure 38. Random read cycle S T A R T SDA LINE S LAV E AD DRES S R E A D S T O P DA TA (n) 1 0 1 0 A 2A 1P 0 D7 D0 A C K R A / C W K Figure 39. Current read cycle S T A R T SDA LINE SLAVE ADDRESS R E A D 1 0 1 0 A2 A1P0 R A / C W K DATA(n+x) DATA(n) D7 S T O P D0 D7 A C K D0 A C K A C K Figure 40. Sequential read cycle (in the case of current read cycle) In random read cycle, data of designated word address can be read. When the command just before current read cycle is random read cycle, current read cycle (each including sequential read cycle), data of incremented last read address (n)-th address, i.e., data of the (n+1)-th address is output. When ACK signal 'LOW' after D0 is detected, and stop condition is not sent from master (-COM) side, the next address data can be read in succession. Read cycle is ended by stop condition where 'H' is input to ACK signal after D0 and SDA signal is started at SCL signal 'H' . When 'H' is not input to ACK signal after D0, sequential read gets in, and the next data is output. Therefore, read command cycle cannot be ended. When to end read command cycle, be sure input stop condition to input 'H' to ACK signal after D0, and to start SDA at SCL signal 'H'. Sequential read is ended by stop condition where 'H' is input to ACK signal after arbitrary D0 and SDA is started at SCL signal 'H'. www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 17/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Software Reset Software reset is executed when to avoid malfunction after power on, and to reset during command input. Software reset has several kinds, and 3 kinds of them are shown in the figure below. (Refer to Figure 41-(a), Figure 41-(b), Figure 41-(c)) In dummy clock input area, release the SDA bus ('H' by pull up). In dummy clock area, ACK output and read data '0' (both 'L' level) may be output from EEPROM, therefore, if 'H' is input forcibly, output may conflict and over current may flow, leading to instantaneous power failure of system power source or influence upon devices. Dummy clock x 14 SCL 1 2 Start x 2 13 Normal command 14 SDA Normal command Figure 41-(a). Dummy clock x 14 + START + START + command input SCL Start Dummy clock x 9 Start 1 2 8 Normal command 9 SDA Normal command Figure 41-(b). START + dummy clock x 9 + START + command input Start x 9 SCL 1 2 3 7 8 Normal command 9 SDA Normal command Figure 41-(c). START x 9 + command input Start command from START input. Acknowledge Polling During internal write execution, all input commands are ignored, therefore ACK is not sent back. During internal automatic write execution after write cycle input, next command (slave address) is sent, and if the first ACK signal sends back 'L', then it means end of write action, while if it sends back 'H', it means now in writing. By use of acknowledge polling, next command can be executed without waiting for tWR = 5ms. When to write continuously, R/W = 0, when to carry out current read cycle after write, slave address R/W = 1 is sent, and if ACK signal sends back 'L', then execute word address input and data output and so forth. During internal write, ACK = HIGH is sent back. First write command S T A R T Write command S T O P S T Slave A R address T A C K H tWR S T Slave A R address T A C K H ... Second write command ... S T Slave A R address T A C K H S T Slave A R address T A C K L Word address A C K L Data A C K L S T O P tWR After completion of internal write, ACK=LOW is sent back, so input next word address and data in succession. Figure 42. Case to continuously write by acknowledge polling www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 18/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A WP Valid Timing (Write Cancel) WP is usually fixed to 'H' or 'L', but when WP is used to cancel write cycle and so forth, pay attention to the following WP valid timing. During write cycle execution, in cancel valid area, by setting WP='H', write cycle can be cancelled. In both byte write cycle and page write cycle, the area from the first start condition of command to the rise of clock to taken in D0 of data(in page write cycle, the first byte data) is cancel invalid area. WP input in this area becomes don't care. The area from the rise of SCL to take in D0 to input the stop condition is cancel valid area. And, after execution of forced end by WP, standby status gets in. Rise of SDA Rise of D0 taken clock SCL SDA SCL D1 D0 ACK SDA S T Slave A R address T A C Word K address L ACK Enlarged view Enlarged view SDA D0 A C D7 D6 D5 D4 D3 D2 D1 D0 K L WP cancel invalid area A C K L Data A C K L S T O P WP cancel valid area tWR WP cancel invalid area WP Data is not written. Figure 43. WP valid timing Command Cancel by Start Condition and Stop Condition During command input, by continuously inputting start condition and stop condition, command can be cancelled. (Figure 44) However, in ACK output area and during data read, SDA bus may output 'L', and in this case, start condition and stop condition cannot be input, so reset is not available. Therefore, execute software reset. And when command is cancelled by start, stop condition, during random read cycle, sequential read cycle, or current read cycle, internal setting address is not determined, therefore, it is not possible to carry out current read cycle in succession. When to carry out read cycle in succession, carry out random read cycle. SCL SDA 1 0 1 0 Start condition Stop condition Figure 44. Case of cancel by start, stop condition during slave address input www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 19/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A I/O Peripheral Circuit Pull up resistance of SDA terminal SDA is NMOS open drain, so requires pull up resistance. As for this resistance value (RPU), select an appropriate value to this resistance value from microcontroller VIL, IL, and VOL-IOL characteristics of this IC. If RPU is large, action frequency is limited. The smaller the RPU, the larger the supply current. Maximum value of RPU The maximum value of RPU is determined by the following factors. SDA rise time to be determined by the capacitance (CBUS) of bus line of RPU and SDA should be tR or below. And AC timing should be satisfied even when SDA rise time is late. The bus electric potential A to be determined by input leak total (IL) of device connected to bus at output of 'H' to SDA bus and RPU should sufficiently secure the input 'H' level (VIH) of microcontroller and EEPROM including recommended noise margin 0.2Vcc. VCCILRPU0.2 VCC VIH 0.8VCCVIH IL IL=10A VIH=0.7 VCC Microcontroller RPU Ex.) VCC =3V from RPU EEPROM RPU SDA terminal A 0.8x30.7x3 -6 10x10 IL IL Bus line capacity 30 k CBUS Figure 45. I/O circuit diagram Minimum value of RPU The minimum value of RPU is determined by the following factors. When IC outputs LOW, it should be satisfied that VOLMAX=0.4V and IOLMAX=3mA. VCCVOL IOL RPU RPU VCCVOL IOL VOLMAX=0.4V should secure the input 'L' level (VIL) of microcontroller and EEPROM including recommended noise margin 0.1Vcc. VOLMAX VIL0.1 VCC Ex.) VCC =3V, VOL=0.4V, IOL=3mA, microcontroller, EEPROM VIL=0.3Vcc from RPU 30.4 3x10 -3 867 And VOL=0.4V VIL=0.3x3 =0.9V Therefore, the condition is satisfied. Pull up resistance of SCL terminal When SCL control is made at CMOS output port, there is no need, but in the case there is timing where SCL becomes 'Hi-Z', add a pull up resistance. As for the pull up resistance, one of several k to several ten k is recommended in consideration of drive performance of output port of microcontroller. www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 20/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Cautions on Microcontroller Connection RS In I2C BUS, it is recommended that SDA port is of open drain input/output. However, when to use CMOS input / output of tri state to SDA port, insert a series resistance Rs between the pull up resistance Rpu and the SDA terminal of EEPROM. This is controls over current that occurs when PMOS of the microcontroller and NMOS of EEPROM are turned ON simultaneously. Rs also plays the role of protection of SDA terminal against surge. Therefore, even when SDA port is open drain input/output, Rs can be used. ACK SCL RPU RS SDA 'H' output of microcontroller 'L' output of EEPROM Over current flows to SDA line by 'H' output of microcontroller and 'L' output of EEPROM. EEPROM Microcontroller Figure 46. I/O circuit diagram Figure 47. Input / output collision timing Maximum value of Rs The maximum value of Rs is determined by the following relations. SDA rise time to be determined by the capacity (CBUS) of bus line of Rpu and SDA should be tR or below. And AC timing should be satisfied even when SDA rise time is late. The bus electric potential A to be determined by Rpu and Rs the moment when EEPROM outputs 'L' to SDA bus sufficiently secure the input 'L' level (VIL) of microcontroller including recommended noise margin 0.1Vcc. (VCCVOL)xRS RPU+RS VCC RPU RS A VOL RS VILVOL0.1VCC 1.1VCC-VIL IOL x RPU Ex.VCC=3V VIL=0.3VCC VOL=0.4V RPU=20k Bus line capacity CBUS VIL + VOL+0.1VCCVIL Micro controller RS EEPROM 0.3x30.40.1x3 1.1x30.3x3 x 20x10 3 1.67k Figure 48. I/O Circuit Diagram Minimum value of Rs The minimum value of Rs is determined by over current at bus collision. When over current flows, noises in power source line, and instantaneous power failure of power source may occur. When allowable over current is defined as I, the following relation must be satisfied. Determine the allowable current in consideration of impedance of power source line in set and so forth. Set the over current to EEPROM 10mA or below. VCC RS RPU 'L'output RS RS Over current I I VCC I Ex.) VCC=3V, I=10mA 'H' output RS Microcontroller EEPROM 3 -3 10x10 300 Figure 49. I/O circuit diagram www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 21/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A I/O Equivalence Circuit Input (A2,A1,SCL, WP) Input / output (SDA) Figure 51. Input / output pin circuit diagram Figure 50. Input pin circuit diagram Power-up / Down Conditions At power on, in IC internal circuit and set, Vcc rises through unstable low voltage area, and IC inside is not completely reset, and malfunction may occur. To prevent this, functions of POR circuit and LVCC circuit are equipped. To assure the action, observe the following conditions at power on. 1. Set SDA = 'H' and SCL ='L' or 'H' 2. Start power source so as to satisfy the recommended conditions of tR, tOFF, and Vbot for operating POR circuit. tR Recommended conditions of tR, tOFF,Vbot tR tOFF Vbot VCC 10ms or below 10ms or larger 0.3V or below tOFF Vbot 100 or below 10ms or larger 0.2V or below 0 Figure 52. Rise waveform diagram 3. Set SDA and SCL so as not to become 'Hi-Z'. When the above conditions 1 and 2 cannot be observed, take the following countermeasures. a) In the case when the above condition 1 cannot be observed. When SDA becomes 'L' at power on . Control SCL and SDA as shown below, to make SCL and SDA, 'H' and 'H'. VCC tLOW SCL SDA After Vcc becomes stable After Vcc becomes stable tDH tSU:DAT Figure 53. When SCL= 'H' and SDA= 'L' tSU:DAT Figure 54. When SCL='L' and SDA='L' b) In the case when the above condition 2 cannot be observed. After power source becomes stable, execute software reset(P18). ) In the case when the above conditions 1 and 2 cannot be observed. Carry out a), and then carry out b). Low Voltage Malfunction Prevention Function LVCC circuit prevents data rewrite action at low power, and prevents wrong write. At LVCC voltage (Typ. =1.2V) or below, it prevent data rewrite. Noise Countermeasures Bypass capacitor When noise or surge gets in the power source line, malfunction may occur, therefore, for removing these, it is recommended to attach a by pass capacitor (0.1F) between IC Vcc and GND. At that moment, attach it as close to IC as possible. And, it is also recommended to attach a bypass capacitor between board Vcc and GND. www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 22/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Operational Notes (1) Described numeric values and data are design representative values, and the values are not guaranteed. (2) We believe that application circuit examples are recommendable, however, in actual use, confirm characteristics further sufficiently. In the case of use by changing the fixed number of external parts, make your decision with sufficient margin in consideration of static characteristics and transition characteristics and fluctuations of external parts and our LSI. (3) Absolute maximum ratings If the absolute maximum ratings such as impressed voltage and action temperature range and so forth are exceeded, LSI may be destructed. Do not impress voltage and temperature exceeding the absolute maximum ratings. In the case of fear exceeding the absolute maximum ratings, take physical safety countermeasures such as fuses, and see to it that conditions exceeding the absolute maximum ratings should not be impressed to LSI. (4) GND electric potential Set the voltage of GND terminal lowest at any action condition. Make sure that each terminal voltage is lower than that of GND terminal. (5) Terminal design In consideration of permissible loss in actual use condition, carry out heat design with sufficient margin. (6) Terminal to terminal shortcircuit and wrong packaging When to package LSI onto a board, pay sufficient attention to LSI direction and displacement. Wrong packaging may destruct LSI. And in the case of shortcircuit between LSI terminals and terminals and power source, terminal and GND owing to foreign matter, LSI may be destructed. (7) Use in a strong electromagnetic field may cause malfunction, therefore, evaluate design sufficiently. www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 23/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Part Numbering B R 2 4 G 0 4 x x x - 3 A x x x x BUS type 24 : I2C Operating temperature/ Operating Voltage -40 to +85 / 1.6V to 5.5V Capacity 04=4K Package Blank : DIP-T8 : SOP-J8 FJ FVJ : TSSOP-B8J NUX : VSON008X2030 : SOP8 F FVT : TSSOP-B8 FVM : MSOP8 Process code Revision G : Halogen free Blank : Not Halogen free As an exception, VSON008X2030 package will be Halogen free with "Blank" T Blank : : 100% Sn 100% Sn Packaging and forming specification E2 : Embossed tape and reel (SOP8, SOP-J8, TSSOP-B8, TSSOP-B8J) TR : Embossed tape and reel (MSOP8, VSON008X2030) None : Tube (DIP-T8) Lineup Package Capacity Type DIP-T8 Quantity Tube of 2000 SOP8 SOP-J8 4K Reel of 2500 Orderable Part Number Remark BR24G04 -3A Not Halogen free 100% Sn BR24G04F -3AGTE2 Halogen free 100% Sn BR24G04FJ -3AGTE2 Halogen free 100% Sn TSSOP-B8 Reel of 3000 BR24G04FVT -3AGE2 Halogen free 100% Sn TSSOP-B8J Reel of 2500 BR24G04FVJ -3AGTE2 Halogen free 100% Sn MSOP8 Reel of 3000 BR24G04FVM -3AGTTR Halogen free 100% Sn VSON008X2030 Reel of 4000 BR24G04NUX -3ATTR Halogen free 100% Sn www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 24/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Physical Dimensions Tape and Reel Information DIP-T8 9.30.3 5 1 4 3.20.2 3.40.3 0.51Min. 6.50.3 8 7.62 0.30.1 0-15 2.54 0.50.1 (Unit : mm) <Tape and Reel information> Container Tube Quantity 2000pcs Direction of feed Direction of products is fixed in a container tube Order quantity needs to be multiple of the minimum quantity. www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 25/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A SOP8 6 5 1 2 3 4 0.3MIN 7 4.40.2 6.20.3 8 +6 4 -4 0.90.15 5.00.2 (MAX 5.35 include BURR) 0.595 1.50.1 +0.1 0.17 -0.05 S S 0.11 0.1 1.27 0.420.1 (Unit : mm) <Tape and Reel information> Tape Embossed carrier tape Quantity 2500pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand Direction of feed 1pin Reel www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 ) Order quantity needs to be multiple of the minimum quantity. 26/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A SOP-J8 4.90.2 (MAX 5.25 include BURR) 7 6 5 1 2 3 4 0.45MIN 8 3.90.2 6.00.3 +6 4 -4 0.545 0.20.1 1.3750.1 S 0.175 1.27 0.420.1 0.1 S (Unit : mm) <Tape and Reel information> Tape Embossed carrier tape Quantity 2500pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand Direction of feed 1pin Reel www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 ) Order quantity needs to be multiple of the minimum quantity. 27/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A TSSOP-B8 3.0 0.1 (MAX 3.35 include BURR) 7 6 5 1 2 3 4 44 1.00.2 0.50.15 1PIN MARK 0.525 +0.05 0.145 -0.03 S 0.10.05 1.2MAX 1.00.05 6.40.2 4.40.1 8 0.08 S +0.05 0.245 -0.04 0.08 M 0.65 (Unit : mm) <Tape and Reel information> Tape Embossed carrier tape Quantity 3000pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand Direction of feed 1pin Reel www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 ) Order quantity needs to be multiple of the minimum quantity. 28/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A TSSOP-B8J 3.0 0.1 (MAX 3.35 include BURR) 5 1 2 3 4 44 0.450.15 1PIN MARK 0.950.2 6 3.00.1 7 +0.05 0.145 -0.03 0.525 S 0.10.05 4.90.2 0.850.05 1.1MAX 8 0.08 S +0.05 0.32 -0.04 0.08 M 0.65 (Unit : mm) <Tape and Reel information> Tape Embossed carrier tape Quantity 2500pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand Direction of feed 1pin Reel www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 ) Order quantity needs to be multiple of the minimum quantity. 29/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A MSOP8 4.00.2 2.80.1 8 7 6 5 0.60.2 +6 4 -4 0.290.15 2.90.1 (MAX 3.25 include BURR) 1 2 3 4 1PIN MARK +0.05 0.145 -0.03 0.475 0.080.05 0.750.05 0.9MAX S +0.05 0.22 -0.04 0.08 S 0.65 (Unit : mm) <Tape and Reel information> Tape Embossed carrier tape Quantity 3000pcs Direction of feed TR The direction is the 1pin of product is at the upper right when you hold ( reel on the left hand and you pull out the tape on the right hand ) 1pin Direction of feed Reel www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 Order quantity needs to be multiple of the minimum quantity. 30/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A VSON008X2030 3.00.1 2.00.1 0.6MAX 1PIN MARK 1.50.1 0.5 1 4 8 5 0.25 1.40.1 0.30.1 C0.25 (0.12) 0.08 S +0.03 0.02 -0.02 S +0.05 0.25 -0.04 (Unit : mm) <Tape and Reel information> Tape Embossed carrier tape Quantity 4000pcs Direction of feed TR The direction is the 1pin of product is at the upper right when you hold ( reel on the left hand and you pull out the tape on the right hand 1pin Reel www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 ) Direction of feed Order quantity needs to be multiple of the minimum quantity. 31/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Marking Diagrams (TOP VIEW) SOP8(TOP VIEW) DIP-T8 (TOP VIEW) Part Number Marking BR24G04A Part Number Marking 4 G 0 4 A LOT Number LOT Number 1PIN MARK SOP-J8(TOP VIEW) TSSOP-B8(TOP VIEW) Part Number Marking 4G04A Part Number Marking 4 G 0 4 A LOT Number LOT Number 1PIN MARK 1PIN MARK TSSOP-B8J(TOP VIEW) MSOP8(TOP VIEW) Part Number Marking 4 G 0 Part Number Marking 4 LOT Number A 4 A 3 G C LOT Number 1PIN MARK 1PIN MARK VSON008X2030 (TOP VIEW) Part Number Marking 4 G 0 LOT Number 4 A 3 1PIN MARK www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 32/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet BR24G04-3A Revision History Date Revision 26.Dec.2012 001 31.May.2013 002 27.Aug.2014 003 Changes New Release P1 Change format of package line-up table and change title. P.2 Add VESD in Absolute Maximum Ratings P.5 Add directions in Pin Descriptions P.3 Modified tSU:STA (0.25->0.20) P.24 Update Part Numbering. Add Lineup Table www.rohm.co (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 33/33 TSZ02201-0R2R0G100560-1-2 27.Aug.2014 REV.003 Datasheet Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you (Note 1) , transport intend to use our Products in devices requiring extremely high reliability (such as medical equipment equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property ("Specific Applications"), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM's Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASS CLASSb CLASS CLASS CLASS CLASS 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM's Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice - GE (c) 2013 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM's internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: 2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice - GE (c) 2013 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM's Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM's Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an "as is" basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice - WE (c) 2014 ROHM Co., Ltd. All rights reserved. Rev.001