ON Semiconductor High Voltage Transistors MMBTA92LT1* MMBTA93LT1 PNP Silicon *ON Semiconductor Preferred Device MAXIMUM RATINGS Symbol MMBTA92 MMBTA93 Unit Collector-Emitter Voltage Rating VCEO -300 -200 Vdc Collector-Base Voltage VCBO -300 -200 Vdc Emitter-Base Voltage VEBO -5.0 -5.0 Vdc Collector Current -- Continuous IC -500 3 1 mAdc 2 DEVICE MARKING CASE 318-08, STYLE 6 SOT-23 (TO-236AF) MMBTA92LT1 = 2D; MMBTA93LT1 = 2E THERMAL CHARACTERISTICS Characteristic Symbol Max Unit PD 225 mW 1.8 mW/C RJA 556 C/W PD 300 mW 2.4 mW/C RJA 417 C/W TJ, Tstg -55 to +150 C Total Device Dissipation FR-5 Board,(1) TA = 25C Derate above 25C Thermal Resistance, Junction to Ambient Total Device Dissipation Alumina Substrate,(2) TA = 25C Derate above 25C Thermal Resistance, Junction to Ambient Junction and Storage Temperature COLLECTOR 3 1 BASE 2 EMITTER ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise noted) Symbol Characteristic Min Max -300 -200 -- -- -300 -200 -- -- -5.0 -- -- -- -0.25 -0.25 -- -0.1 Unit OFF CHARACTERISTICS Collector-Emitter Breakdown Voltage(3) (IC = -1.0 mAdc, IB = 0) V(BR)CEO MMBTA92 MMBTA93 Collector-Base Breakdown Voltage (IC = -100 Adc, IE = 0) Vdc V(BR)CBO MMBTA92 MMBTA93 Emitter-Base Breakdown Voltage (IE = -100 Adc, IC = 0) V(BR)EBO Collector Cutoff Current (VCB = -200 Vdc, IE = 0) (VCB = -160 Vdc, IE = 0) Vdc Adc ICBO MMBTA92 MMBTA93 Emitter Cutoff Current (VEB = -3.0 Vdc, IC = 0) IEBO Vdc Adc 1. FR-5 = 1.0 x 0.75 x 0.062 in. 2. Alumina = 0.4 x 0.3 x 0.024 in. 99.5% alumina. 3. Pulse Test: Pulse Width 300 s, Duty Cycle 2.0%. Preferred devices are ON Semiconductor recommended choices for future use and best overall value. Semiconductor Components Industries, LLC, 2001 March, 2001 - Rev. 2 1 Publication Order Number: MMBTA92LT1/D MMBTA92LT1 MMBTA93LT1 ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise noted) (Continued) Symbol Min Max Both Types Both Types 25 40 -- -- MMBTA92 MMBTA93 25 25 -- -- -- -- -0.5 -0.5 VBE(sat) -- -0.9 Vdc fT 50 -- MHz -- -- 6.0 8.0 Characteristic ON Unit CHARACTERISTICS(3) DC Current Gain (IC = -1.0 mAdc, VCE = -10 Vdc) (IC = -10 mAdc, VCE = -10 Vdc) hFE (IC = -30 mAdc, VCE = -10 Vdc) Collector-Emitter Saturation Voltage (IC = -20 mAdc, IB = -2.0 mAdc) -- VCE(sat) MMBTA92 MMBTA93 Base-Emitter Saturation Voltage (IC = -20 mAdc, IB = -2.0 mAdc) Vdc SMALL-SIGNAL CHARACTERISTICS Current-Gain -- Bandwidth Product (IC = -10 mAdc, VCE = -20 Vdc, f = 100 MHz) Collector-Base Capacitance (VCB = -20 Vdc, IE = 0, f = 1.0 MHz) Ccb MMBTA92 MMBTA93 3. Pulse Test: Pulse Width 300 s, Duty Cycle 2.0%. http://onsemi.com 2 pF MMBTA92LT1 MMBTA93LT1 300 hFE , DC CURRENT GAIN VCE = 10 Vdc TJ = +125C 250 200 25C 150 -55C 100 50 0 0.1 1.0 10 100 IC, COLLECTOR CURRENT (mA) C, CAPACITANCE (pF) 100 f, T CURRENT-GAIN BANDWIDTH (MHz) Figure 1. DC Current Gain Cib @ 1MHz 10 Ccb @ 1MHz 1.0 0.1 0.1 1.0 10 100 VR, REVERSE VOLTAGE (VOLTS) 150 130 110 90 70 50 30 10 1000 TJ = 25C VCE = 20 Vdc F = 20 MHz 1 Figure 2. Capacitance 3 5 11 13 15 7 9 IC, COLLECTOR CURRENT (mA) 17 19 21 Figure 3. Current-Gain -- Bandwidth 1.4 V, VOLTAGE (VOLTS) 1.2 VCE(sat) @ 25C, IC/IB = 10 VCE(sat) @ 125C, IC/IB = 10 VCE(sat) @ -55C, IC/IB = 10 VBE(sat) @ 25C, IC/IB = 10 1.0 0.8 VBE(sat) @ 125C, IC/IB = 10 VBE(sat) @ -55C, IC/IB = 10 VBE(on) @ 25C, VCE = 10 V VBE(on) @ 125C, VCE = 10 V VBE(on) @ -55C, VCE = 10 V 0.6 0.4 0.2 0.0 0.1 1.0 10 IC, COLLECTOR CURRENT (mA) 100 Figure 4. "ON" Voltages http://onsemi.com 3 MMBTA92LT1 MMBTA93LT1 INFORMATION FOR USING THE SOT-23 SURFACE MOUNT PACKAGE MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to insure proper solder connection interface between the board and the package. With the correct pad geometry, the packages will self align when subjected to a solder reflow process. 0.037 0.95 0.037 0.95 0.079 2.0 0.035 0.9 0.031 0.8 inches mm SOT-23 SOT-23 POWER DISSIPATION SOLDERING PRECAUTIONS The power dissipation of the SOT-23 is a function of the pad size. This can vary from the minimum pad size for soldering to a pad size given for maximum power dissipation. Power dissipation for a surface mount device is determined by TJ(max), the maximum rated junction temperature of the die, RJA, the thermal resistance from the device junction to ambient, and the operating temperature, TA. Using the values provided on the data sheet for the SOT-23 package, PD can be calculated as follows: PD = * * TJ(max) - TA RJA * The values for the equation are found in the maximum ratings table on the data sheet. Substituting these values into the equation for an ambient temperature TA of 25C, one can calculate the power dissipation of the device which in this case is 225 milliwatts. PD = 150C - 25C 556C/W * = 225 milliwatts * The 556C/W for the SOT-23 package assumes the use of the recommended footprint on a glass epoxy printed circuit board to achieve a power dissipation of 225 milliwatts. There are other alternatives to achieving higher power dissipation from the SOT-23 package. Another alternative would be to use a ceramic substrate or an aluminum core board such as Thermal Clad. Using a board material such as Thermal Clad, an aluminum core board, the power dissipation can be doubled using the same footprint. * * The melting temperature of solder is higher than the rated temperature of the device. When the entire device is heated to a high temperature, failure to complete soldering within a short time could result in device failure. Therefore, the following items should always be observed in order to minimize the thermal stress to which the devices are subjected. Always preheat the device. The delta temperature between the preheat and soldering should be 100C or less.* When preheating and soldering, the temperature of the leads and the case must not exceed the maximum temperature ratings as shown on the data sheet. When using infrared heating with the reflow soldering method, the difference shall be a maximum of 10C. The soldering temperature and time shall not exceed 260C for more than 10 seconds. When shifting from preheating to soldering, the maximum temperature gradient shall be 5C or less. After soldering has been completed, the device should be allowed to cool naturally for at least three minutes. Gradual cooling should be used as the use of forced cooling will increase the temperature gradient and result in latent failure due to mechanical stress. Mechanical stress or shock should not be applied during cooling. * Soldering a device without preheating can cause excessive thermal shock and stress which can result in damage to the device. http://onsemi.com 4 MMBTA92LT1 MMBTA93LT1 PACKAGE DIMENSIONS SOT-23 (TO-236) CASE 318-08 ISSUE AF NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. A L 3 1 V B S 2 G C D H K J STYLE 6: PIN 1. BASE 2. EMITTER 3. COLLECTOR http://onsemi.com 5 DIM A B C D G H J K L S V INCHES MIN MAX 0.1102 0.1197 0.0472 0.0551 0.0350 0.0440 0.0150 0.0200 0.0701 0.0807 0.0005 0.0040 0.0034 0.0070 0.0140 0.0285 0.0350 0.0401 0.0830 0.1039 0.0177 0.0236 MILLIMETERS MIN MAX 2.80 3.04 1.20 1.40 0.89 1.11 0.37 0.50 1.78 2.04 0.013 0.100 0.085 0.177 0.35 0.69 0.89 1.02 2.10 2.64 0.45 0.60 MMBTA92LT1 MMBTA93LT1 Notes http://onsemi.com 6 MMBTA92LT1 MMBTA93LT1 Notes http://onsemi.com 7 MMBTA92LT1 MMBTA93LT1 Thermal Clad is a trademark of the Bergquist Company ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com Fax Response Line: 303-675-2167 or 800-344-3810 Toll Free USA/Canada N. American Technical Support: 800-282-9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor - European Support German Phone: (+1) 303-308-7140 (Mon-Fri 2:30pm to 7:00pm CET) Email: ONlit-german@hibbertco.com French Phone: (+1) 303-308-7141 (Mon-Fri 2:00pm to 7:00pm CET) Email: ONlit-french@hibbertco.com English Phone: (+1) 303-308-7142 (Mon-Fri 12:00pm to 5:00pm GMT) Email: ONlit@hibbertco.com CENTRAL/SOUTH AMERICA: Spanish Phone: 303-308-7143 (Mon-Fri 8:00am to 5:00pm MST) Email: ONlit-spanish@hibbertco.com Toll-Free from Mexico: Dial 01-800-288-2872 for Access - then Dial 866-297-9322 ASIA/PACIFIC: LDC for ON Semiconductor - Asia Support Phone: 303-675-2121 (Tue-Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong & Singapore: 001-800-4422-3781 Email: ONlit-asia@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com EUROPEAN TOLL-FREE ACCESS*: 00-800-4422-3781 *Available from Germany, France, Italy, UK, Ireland For additional information, please contact your local Sales Representative. http://onsemi.com 8 MMBTA92LT1/D