LM111,LM211,LM311
LM111/LM211/LM311 Voltage Comparator
Literature Number: SNOSBJ1C
LM111/LM211/LM311
Voltage Comparator
1.0 General Description
The LM111, LM211 and LM311 are voltage comparators that
have input currents nearly a thousand times lower than
devices like the LM106 or LM710. They are also designed to
operate over a wider range of supply voltages: from standard
±15V op amp supplies down to the single 5V supply used for
IC logic. Their output is compatible with RTL, DTL and TTL
as well as MOS circuits. Further, they can drive lamps or
relays, switching voltages up to 50V at currents as high as
50 mA.
Both the inputs and the outputs of the LM111, LM211 or the
LM311 can be isolated from system ground, and the output
can drive loads referred to ground, the positive supply or the
negative supply. Offset balancing and strobe capability are
provided and outputs can be wire OR’ed. Although slower
than the LM106 and LM710 (200 ns response time vs 40 ns)
the devices are also much less prone to spurious oscilla-
tions. The LM111 has the same pin configuration as the
LM106 and LM710.
The LM211 is identical to the LM111, except that its perfor-
mance is specified over a −25˚C to +85˚C temperature range
instead of −55˚C to +125˚C. The LM311 has a temperature
range of 0˚C to +70˚C.
2.0 Features
nOperates from single 5V supply
nInput current: 150 nA max. over temperature
nOffset current: 20 nA max. over temperature
nDifferential input voltage range: ±30V
nPower consumption: 135 mW at ±15V
3.0 Typical Applications (Note 3)
Offset Balancing Strobing
00570436
00570437
Note: Do Not Ground Strobe Pin. Output is turned off when current is
pulled from Strobe Pin.
Increasing Input Stage Current (Note 1) Detector for Magnetic Transducer
00570438
Note 1: Increases typical common mode slew from 7.0V/µs to 18V/µs.
00570439
January 2001
LM111/LM211/LM311 Voltage Comparator
© 2004 National Semiconductor Corporation DS005704 www.national.com
3.0 Typical Applications (Note 3) (Continued)
Digital Transmission Isolator Relay Driver with Strobe
00570440
00570441
*Absorbs inductive kickback of relay and protects IC from severe voltage
transients on V++ line.
Note: Do Not Ground Strobe Pin.
Strobing off Both Input and Output Stages (Note 2)
00570442
Note: Do Not Ground Strobe Pin.
Note 2: Typical input current is 50 pA with inputs strobed off.
Note 3: Pin connections shown on schematic diagram and typical applications are for H08 metal can package.
Positive Peak Detector Zero Crossing Detector Driving MOS Logic
00570423
*Solid tantalum
00570424
LM111/LM211/LM311
www.national.com 2
4.0 Absolute Maximum Ratings for
the LM111/LM211(Note 10)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Total Supply Voltage (V
84
) 36V
Output to Negative Supply Voltage
(V
74
) 50V
Ground to Negative Supply Voltage
(V
14
) 30V
Differential Input Voltage ±30V
Input Voltage (Note 4) ±15V
Output Short Circuit Duration 10 sec
Operating Temperature Range
LM111 −55˚C to 125˚C
LM211 −25˚C to 85˚C
Lead Temperature (Soldering, 10 sec) 260˚C
Voltage at Strobe Pin V
+
−5V
Soldering Information
Dual-In-Line Package
Soldering (10 seconds) 260˚C
Small Outline Package
Vapor Phase (60 seconds) 215˚C
Infrared (15 seconds) 220˚C
See AN-450 “Surface Mounting Methods and Their Effect
on Product Reliability” for other methods of soldering
surface mount devices.
ESD Rating (Note 11) 300V
Electrical Characteristics (Note 6) for the LM111 and LM211
Parameter Conditions Min Typ Max Units
Input Offset Voltage (Note 7) T
A
=25˚C, R
S
50k 0.7 3.0 mV
Input Offset Current T
A
=25˚C 4.0 10 nA
Input Bias Current T
A
=25˚C 60 100 nA
Voltage Gain T
A
=25˚C 40 200 V/mV
Response Time (Note 8) T
A
=25˚C 200 ns
Saturation Voltage V
IN
−5 mV, I
OUT
=50 mA 0.75 1.5 V
T
A
=25˚C
Strobe ON Current (Note 9) T
A
=25˚C 2.0 5.0 mA
Output Leakage Current V
IN
5 mV, V
OUT
=35V 0.2 10 nA
T
A
=25˚C, I
STROBE
=3 mA
Input Offset Voltage (Note 7) R
S
50 k 4.0 mV
Input Offset Current (Note 7) 20 nA
Input Bias Current 150 nA
Input Voltage Range V
+
=15V, V
=−15V, Pin 7 −14.5 13.8,-14.7 13.0 V
Pull-Up May Go To 5V
Saturation Voltage V
+
4.5V, V
=0 0.23 0.4 V
V
IN
−6 mV, I
OUT
8mA
Output Leakage Current V
IN
5 mV, V
OUT
=35V 0.1 0.5 µA
Positive Supply Current T
A
=25˚C 5.1 6.0 mA
Negative Supply Current T
A
=25˚C 4.1 5.0 mA
Note 4: This rating applies for ±15 supplies. The positive input voltage limit is 30V above the negative supply. The negative input voltage limit is equal to the
negative supply voltage or 30V below the positive supply, whichever is less.
Note 5: The maximum junction temperature of the LM111 is 150˚C, while that of the LM211 is 110˚C. For operating at elevated temperatures, devices in the H08
package must be derated based on a thermal resistance of 165˚C/W, junction to ambient, or 20˚C/W, junction to case. The thermal resistance of the dual-in-line
package is 110˚C/W, junction to ambient.
Note 6: These specifications apply for VS=±15V and Ground pin at ground, and −55˚CTA+125˚C, unless otherwise stated. With the LM211, however, all
temperature specifications are limited to −25˚CTA+85˚C. The offset voltage, offset current and bias current specifications apply for any supply voltage from a single
5V supply up to ±15V supplies.
Note 7: The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply witha1mAload. Thus, these
parameters define an error band and take into account the worst-case effects of voltage gain and RS.
Note 8: The response time specified (see definitions) is for a 100 mV input step with 5 mV overdrive.
Note 9: This specification gives the range of current which must be drawn from the strobe pin to ensure the output is properly disabled. Do not short the strobe pin
to ground; it should be current driven at 3 to 5 mA.
Note 10: Refer to RETS111X for the LM111H, LM111J and LM111J-8 military specifications.
Note 11: Human body model, 1.5 kin series with 100 pF.
LM111/LM211/LM311
www.national.com3
5.0 Absolute Maximum Ratings for
the LM311(Note 12)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Total Supply Voltage (V
84
) 36V
Output to Negative Supply Voltage
(V
74
) 40V
Ground to Negative Supply Voltage
(V
14
) 30V
Differential Input Voltage ±30V
Input Voltage (Note 13) ±15V
Power Dissipation (Note 14) 500 mW
ESD Rating (Note 19) 300V
Output Short Circuit Duration 10 sec
Operating Temperature Range to 70˚C
Storage Temperature Range −65˚C to 150˚C
Lead Temperature (soldering, 10 sec) 260˚C
Voltage at Strobe Pin V
+
−5V
Soldering Information
Dual-In-Line Package
Soldering (10 seconds) 260˚C
Small Outline Package
Vapor Phase (60 seconds) 215˚C
Infrared (15 seconds) 220˚C
See AN-450 “Surface Mounting Methods and Their Effect
on Product Reliability” for other methods of soldering
surface mount devices.
Electrical Characteristics (Note 15) for the LM311
Parameter Conditions Min Typ Max Units
Input Offset Voltage (Note 16) T
A
=25˚C, R
S
50k 2.0 7.5 mV
Input Offset Current(Note 16) T
A
=25˚C 6.0 50 nA
Input Bias Current T
A
=25˚C 100 250 nA
Voltage Gain T
A
=25˚C 40 200 V/mV
Response Time (Note 17) T
A
=25˚C 200 ns
Saturation Voltage V
IN
−10 mV, I
OUT
=50 mA 0.75 1.5 V
T
A
=25˚C
Strobe ON Current (Note 18) T
A
=25˚C 2.0 5.0 mA
Output Leakage Current V
IN
10 mV, V
OUT
=35V
T
A
=25˚C, I
STROBE
=3 mA 0.2 50 nA
V
= Pin 1 = −5V
Input Offset Voltage (Note 16) R
S
50K 10 mV
Input Offset Current (Note 16) 70 nA
Input Bias Current 300 nA
Input Voltage Range −14.5 13.8,−14.7 13.0 V
Saturation Voltage V
+
4.5V, V
=0 0.23 0.4 V
V
IN
−10 mV, I
OUT
8mA
Positive Supply Current T
A
=25˚C 5.1 7.5 mA
Negative Supply Current T
A
=25˚C 4.1 5.0 mA
Note 12: “Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits.”
Note 13: This rating applies for ±15V supplies. The positive input voltage limit is 30V above the negative supply. The negative input voltage limit is equal to the
negative supply voltage or 30V below the positive supply, whichever is less.
Note 14: The maximum junction temperature of the LM311 is 110˚C. For operating at elevated temperature, devices in the H08 package must be derated based
on a thermal resistance of 165˚C/W, junction to ambient, or 20˚C/W, junction to case. The thermal resistance of the dual-in-line package is 100˚C/W, junction to
ambient.
Note 15: These specifications apply for VS=±15V and Pin 1 at ground, and 0˚C <TA<+70˚C, unless otherwise specified. The offset voltage, offset current and
bias current specifications apply for any supply voltage from a single 5V supply up to ±15V supplies.
Note 16: The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with 1 mA load. Thus, these
parameters define an error band and take into account the worst-case effects of voltage gain and RS.
Note 17: The response time specified (see definitions) is for a 100 mV input step with 5 mV overdrive.
Note 18: This specification gives the range of current which must be drawn from the strobe pin to ensure the output is properly disabled. Do not short the strobe
pin to ground; it should be current driven at 3 to 5 mA.
Note 19: Human body model, 1.5 kin series with 100 pF.
LM111/LM211/LM311
www.national.com 4
6.0 LM111/LM211 Typical Performance Characteristics
Input Bias Current Input Bias Current
00570443 00570444
Input Bias Current Input Bias Current
00570445
00570446
Input Bias Current Input Bias Current
00570447 00570448
LM111/LM211/LM311
www.national.com5
6.0 LM111/LM211 Typical Performance Characteristics (Continued)
Input Bias Current
Input Overdrives
Input Bias Current
Input Overdrives
00570449 00570450
Input Bias Current
Response Time for Various
Input Overdrives
00570451
00570452
Response Time for Various
Input Overdrives Output Limiting Characteristics
00570453
00570454
LM111/LM211/LM311
www.national.com 6
6.0 LM111/LM211 Typical Performance Characteristics (Continued)
Supply Current Supply Current
00570455 00570456
Leakage Currents
00570457
7.0 LM311 Typical Performance Characteristics
Input Bias Current Input Offset Current
00570458 00570459
LM111/LM211/LM311
www.national.com7
7.0 LM311 Typical Performance Characteristics (Continued)
Offset Error Input Characteristics
00570460 00570461
Common Mode Limits Transfer Function
00570462 00570463
Response Time for Various
Input Overdrives
Response Time for Various
Input Overdrives
00570464 00570465
LM111/LM211/LM311
www.national.com 8
7.0 LM311 Typical Performance Characteristics (Continued)
Output Saturation Voltage
Response Time for Various
Input Overdrives
00570466
00570467
Response Time for Various
Input Overdrives Output Limiting Characteristics
00570468
00570469
Supply Current Supply Current
00570470 00570471
LM111/LM211/LM311
www.national.com9
7.0 LM311 Typical Performance Characteristics (Continued)
Leakage Currents
00570472
8.0 Application Hints
8.1 CIRCUIT TECHNIQUES FOR AVOIDING
OSCILLATIONS IN COMPARATOR APPLICATIONS
When a high-speed comparator such as the LM111 is used
with fast input signals and low source impedances, the out-
put response will normally be fast and stable, assuming that
the power supplies have been bypassed (with 0.1 µF disc
capacitors), and that the output signal is routed well away
from the inputs (pins 2 and 3) and also away from pins 5 and
6.
However, when the input signal is a voltage ramp or a slow
sine wave, or if the signal source impedance is high (1 kto
100 k), the comparator may burst into oscillation near the
crossing-point. This is due to the high gain and wide band-
width of comparators like the LM111. To avoid oscillation or
instability in such a usage, several precautions are recom-
mended, as shown in Figure 1 below.
1. The trim pins (pins 5 and 6) act as unwanted auxiliary
inputs. If these pins are not connected to a trim-pot, they
should be shorted together. If they are connected to a
trim-pot, a 0.01 µF capacitor C1 between pins 5 and 6
will minimize the susceptibility to AC coupling. A smaller
capacitor is used if pin 5 is used for positive feedback as
in Figure 1.
2. Certain sources will produce a cleaner comparator out-
put waveform if a 100 pF to 1000 pF capacitor C2 is
connected directly across the input pins.
3. When the signal source is applied through a resistive
network, R
S
, it is usually advantageous to choose an R
S
'
of substantially the same value, both for DC and for
dynamic (AC) considerations. Carbon, tin-oxide, and
metal-film resistors have all been used successfully in
comparator input circuitry. Inductive wirewound resistors
are not suitable.
4. When comparator circuits use input resistors (eg. sum-
ming resistors), their value and placement are particu-
larly important. In all cases the body of the resistor
should be close to the device or socket. In other words
there should be very little lead length or printed-circuit
foil run between comparator and resistor to radiate or
pick up signals. The same applies to capacitors, pots,
etc. For example, if R
S
=10 k, as little as 5 inches of
lead between the resistors and the input pins can result
in oscillations that are very hard to damp. Twisting these
input leads tightly is the only (second best) alternative to
placing resistors close to the comparator.
5. Since feedback to almost any pin of a comparator can
result in oscillation, the printed-circuit layout should be
engineered thoughtfully. Preferably there should be a
groundplane under the LM111 circuitry, for example, one
side of a double-layer circuit card. Ground foil (or, posi-
tive supply or negative supply foil) should extend be-
tween the output and the inputs, to act as a guard. The
foil connections for the inputs should be as small and
compact as possible, and should be essentially sur-
rounded by ground foil on all sides, to guard against
capacitive coupling from any high-level signals (such as
the output). If pins 5 and 6 are not used, they should be
shorted together. If they are connected to a trim-pot, the
trim-pot should be located, at most, a few inches away
from the LM111, and the 0.01 µF capacitor should be
installed. If this capacitor cannot be used, a shielding
printed-circuit foil may be advisable between pins 6 and
7. The power supply bypass capacitors should be lo-
cated within a couple inches of the LM111. (Some other
comparators require the power-supply bypass to be lo-
cated immediately adjacent to the comparator.)
6. It is a standard procedure to use hysteresis (positive
feedback) around a comparator, to prevent oscillation,
and to avoid excessive noise on the output because the
comparator is a good amplifier for its own noise. In the
circuit of Figure 2, the feedback from the output to the
positive input will cause about 3 mV of hysteresis. How-
ever, if R
S
is larger than 100, such as 50 k, it would
not be reasonable to simply increase the value of the
positive feedback resistor above 510 k. The circuit of
Figure 3 could be used, but it is rather awkward. See the
notes in paragraph 7 below.
LM111/LM211/LM311
www.national.com 10
8.0 Application Hints (Continued)
7. When both inputs of the LM111 are connected to active
signals, or if a high-impedance signal is driving the
positive input of the LM111 so that positive feedback
would be disruptive, the circuit of Figure 1 is ideal. The
positive feedback is to pin 5 (one of the offset adjust-
ment pins). It is sufficient to cause 1 to 2 mV hysteresis
and sharp transitions with input triangle waves from a
few Hz to hundreds of kHz. The positive-feedback signal
across the 82resistor swings 240 mV below the posi-
tive supply. This signal is centered around the nominal
voltage at pin 5, so this feedback does not add to the
V
OS
of the comparator. As much as 8 mV of V
OS
can be
trimmed out, using the 5 kpot and 3 kresistor as
shown.
8. These application notes apply specifically to the LM111,
LM211, LM311, and LF111 families of comparators, and
are applicable to all high-speed comparators in general,
(with the exception that not all comparators have trim
pins).
00570429
Pin connections shown are for LM111H in the H08 hermetic package
FIGURE 1. Improved Positive Feedback
00570430
Pin connections shown are for LM111H in the H08 hermetic package
FIGURE 2. Conventional Positive Feedback
LM111/LM211/LM311
www.national.com11
8.0 Application Hints (Continued)
9.0 Typical Applications (Pin numbers
refer to H08 package)
Zero Crossing Detector Driving MOS Switch 100 kHz Free Running Multivibrator
00570413
00570414
*TTL or DTL fanout of two
00570431
FIGURE 3. Positive Feedback with High Source Resistance
LM111/LM211/LM311
www.national.com 12
9.0 Typical Applications (Pin numbers refer to H08 package) (Continued)
10 Hz to 10 kHz Voltage Controlled Oscillator
00570415
*Adjust for symmetrical square wave time when VIN =5mV
Minimum capacitance 20 pF Maximum frequency 50 kHz
Driving Ground-Referred Load Using Clamp Diodes to Improve Response
00570416
*Input polarity is reversed when using pin 1 as output.
00570417
TTL Interface with High Level Logic
00570418
*Values shown are fora0to30Vlogic swing and a 15V threshold.
May be added to control speed and reduce susceptibility to noise spikes.
LM111/LM211/LM311
www.national.com13
9.0 Typical Applications (Pin numbers refer to H08 package) (Continued)
Crystal Oscillator Comparator and Solenoid Driver
00570419
00570420
Precision Squarer
00570421
*Solid tantalum
Adjust to set clamp level
LM111/LM211/LM311
www.national.com 14
9.0 Typical Applications (Pin numbers refer to H08 package) (Continued)
Low Voltage Adjustable Reference Supply
00570422
*Solid tantalum
Positive Peak Detector Zero Crossing Detector Driving MOS Logic
00570423
*Solid tantalum
00570424
Negative Peak Detector
00570425
*Solid tantalum
LM111/LM211/LM311
www.national.com15
9.0 Typical Applications (Pin numbers refer to H08 package) (Continued)
Precision Photodiode Comparator
00570426
*R2 sets the comparison level. At comparison, the photodiode has less than 5 mV across it, decreasing leakages by an order of magnitude.
Switching Power Amplifier
00570427
LM111/LM211/LM311
www.national.com 16
9.0 Typical Applications (Pin numbers refer to H08 package) (Continued)
Switching Power Amplifier
00570428
LM111/LM211/LM311
www.national.com17
10.0 Schematic Diagram (Note 20)
00570405
Note 20: Pin connections shown on schematic diagram are for H08 package.
LM111/LM211/LM311
www.national.com 18
11.0 Connection Diagrams
Metal Can Package
00570406
Note: Pin 4 connected to case
Top View
Order Number LM111H, LM111H/883(Note 21) , LM211H or LM311H
See NS Package Number H08C
Dual-In-Line Package Dual-In-Line Package
00570434
Top View
Order Number LM111J-8, LM111J-8/883(Note 21),
LM311M, LM311MX or LM311N
See NS Package Number J08A, M08A or N08E
00570435
Top View
Order Number LM111J/883(Note 21)
See NS Package Number J14A or N14A
00570433
Order Number LM111W/883(Note 21), LM111WG/883
See NS Package Number W10A, WG10A
Note 21: Also available per JM38510/10304
LM111/LM211/LM311
www.national.com19
12.0 Physical Dimensions inches (millimeters) unless otherwise noted
Metal Can Package (H)
Order Number LM111H, LM111H/883, LM211H or LM311H
NS Package Number H08C
Cavity Dual-In-Line Package (J)
Order Number LM111J-8, LM111J-8/883
NS Package Number J08A
LM111/LM211/LM311
www.national.com 20
12.0 Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Dual-In-Line Package (J)
Order Number LM111J/883
NS Package Number J14A
Dual-In-Line Package (M)
Order Number LM311M, LM311MX
NS Package Number M08A
LM111/LM211/LM311
www.national.com21
12.0 Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Dual-In-Line Package (N)
Order Number LM311N
NS Package Number N08E
Order Number LM111W/883, LM111WG/883
NS Package Number W10A, WG10A
LM111/LM211/LM311
www.national.com 22
Notes
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship
Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned
Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Support Center
Email: ap.support@nsc.com
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
LM111/LM211/LM311 Voltage Comparator
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TIs terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TIs standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated