Low Cost, Precision Analog Front End and
Controller for Battery Test/Formation Systems
Data Sheet
AD8451
FEATURES
Integrated constant current and voltage modes with
automatic switchover
Charge and discharge modes
Precision voltage and current measurement
Integrated precision control feedback blocks
Precision interface to PWM or linear power converters
Fixed gain settings
Current sense gain: 26 V/V (typ)
Voltage sense gain: 0.8 V/V (typ)
Excellent ac and dc performance
Maximum offset voltage drift: 0.9 µV/°C
Maximum gain drift: 3 ppm/°C
Low current sense amplifier input voltage noise: 9 nV/√Hz typ
Current sense CMRR: 108 dB min
TTL compliant logic
APPLICATIONS
Battery cell formation and testing
Battery module testing
GENERAL DESCRIPTION
The AD8451 is a precision analog front end and controller for
testing and monitoring battery cells. A precision fixed gain
instrumentation amplifier (IA) measures the battery charge/
discharge current, and a fixed gain difference amplifier (DA)
measures the battery voltage (see Figure 1). Internal laser
trimmed resistor networks set the gains for the IA and the DA,
optimizing the performance of the AD8451 over the rated
temperature range. The IA gain is 26 V/V and the DA gain is
0.8 V/V.
Voltages at the ISET and VSET inputs set the desired constant
current (CC) and constant voltage (CV) values. CC to CV
switching is automatic and transparent to the system.
A TTL logic level input, MODE, selects the charge or discharge
mode (high for charge, and low for discharge). An analog output,
VCTRL, interfaces directly with the Analog Devices, Inc.,
ADP1972 pulse-width modulation (PWM) controller.
The AD8451 simplifies designs by providing excellent accuracy,
performance over temperature, flexibility with functionality,
and overall reliability in a space-saving package. The AD8451 is
available in an 80-lead, 14 mm × 14 mm × 1.40 mm LQFP and
is rated for an operating temperature of −40°C to +85°C.
FUNCTIONAL BLOCK DIAGRAM
CURRENT
SENSE IA
VOLTAGE
SENSE DA
ISMEA ISET
BVMEA VSET VINT
MUX
ISVN
ISVP
BVN
BVP
VINT
VCTRL×1
MODE
AD8451
IVE0/IVE1
VVE0/
VVE1
(CHARGE/
DISCHARGE)
SWITCHING
VVP0 VSETBF
VCLP
VCLN
BVREFH/
BVREFL
ISREFH/
ISREFL
VREF
0.8
VOLTAGE
REFERENCE
CONSTANT
VOLTAGE LOOP
FILTER
CONSTANT
CURRENT LO OP
FILTER
26
12137-001
Figure 1.
Rev. 0 Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2014 Analog Devices, Inc. All rights reserved.
Technical Support www.analog.com
AD8451 Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications ....................................................................................... 1
General Description ......................................................................... 1
Functional Block Diagram .............................................................. 1
Revision History ............................................................................... 2
Specifications ..................................................................................... 3
Absolute Maximum Ratings ............................................................ 6
Thermal Resistance ...................................................................... 6
ESD Caution .................................................................................. 6
Pin Configuration and Function Descriptions ............................. 7
Typical Performance Characteristics ............................................. 9
IA Characteristics ......................................................................... 9
DA Characteristics ..................................................................... 11
CC and CV Loop Filter Amplifiers, and VSET Buffer .......... 13
VINT Buffer ................................................................................ 15
Reference Characteristics .......................................................... 16
Theory of Operation ...................................................................... 17
Overview ...................................................................................... 17
Instrumentation Amplifier (IA) ............................................... 18
Difference Amplifier (DA) ........................................................ 19
CC and CV Loop Filter Amplifiers .......................................... 19
MODE Pin, Charge and Discharge Control ........................... 21
Applications Information .............................................................. 22
Functional Description .............................................................. 22
Power Supply Connections ....................................................... 23
Current Sense IA Connections ................................................. 23
Voltage Sense DA Connections ................................................ 23
Battery Current and Voltage Control Inputs (ISET and VSET)
....................................................................................................... 23
Loop Filter Amplifiers ............................................................... 24
Connecting to a PWM Controller (VCTRL Pin) ...................... 24
Step-by-Step Design Example................................................... 24
Evaluation Board ............................................................................ 26
Introduction ................................................................................ 26
Features and Tests ....................................................................... 26
Evaluating the AD8451 .............................................................. 27
Schematic and Artwork ............................................................. 28
Outline Dimensions ....................................................................... 32
Ordering Guide .......................................................................... 32
REVISION HISTORY
3/14—Revision 0: Initial Version
Rev. 0 | Page 2 of 32
Data Sheet AD8451
SPECIFICATIONS
AVCC = +15 V, AVEE = −15 V; DVCC = +5 V; TA = 25°C, unless otherwise noted.
Table 1.
Parameter Test Conditions/Comments Min Typ Max Unit
CURRENT SENSE INSTRUMENTATION AMPLIFIER
Internal Fixed Gain 26 V/V
Gain Error VISMEA = ±10 V ±0.1 %
Gain Drift TA = TMIN to TMAX 3 ppm/°C
Gain Nonlinearity VISMEA = ±10 V, RL = 2 kΩ 3 ppm
Offset Voltage (RTI) ISREFH and ISREFL pins grounded −110 +110 µV
Offset Voltage Drift
T
A
= T
MIN
to T
MAX
0.9
Input Bias Current 15 30 nA
Temperature Coefficient TA = TMIN to TMAX 150 pA/°C
Input Offset Current 2 nA
Temperature Coefficient TA = TMIN to TMAX 10 pA/°C
Input Common-Mode Voltage Range VISVP − VISVN = 0 V AVEE + 2.3 AVCC − 2.4 V
Over Temperature TA = TMIN to TMAX AVEE + 2.6 AVCC − 2.6 V
Overvoltage Input Range AVCC − 55 AVEE + 55 V
Differential Input Impedance 150 GΩ
Input Common-Mode Impedance 150 GΩ
Output Voltage Swing AVEE + 1.5 AVCC − 1.2 V
Over Temperature TA = TMIN to TMAX AVEE + 1.7 AVCC − 1.4 V
Capacitive Load Drive 1000 pF
Short-Circuit Current 40 mA
Reference Input Voltage Range ISREFH and ISREFL pins tied together AVEE AVCC V
Reference Input Bias Current VISVP = VISVN = 0 V 5 µA
Output Voltage Level Shift ISREFL pin grounded
Maximum
ISREFH pin connected to VREF pin
17
20
23
Scale Factor VISMEA/VISREFH 6.8 8 9.2 mV/V
Common-Mode Rejection Ratio (CMRR) ΔVCM = 20 V 108 dB
Temperature Coefficient TA = TMIN to TMAX 0.01 µV/V/°C
Power Supply Rejection Ratio (PSRR) ΔVS = 20 V 108 122 dB
Voltage Noise f = 1 kHz 9 nV/√Hz
Voltage Noise, Peak to Peak f = 0.1 Hz to 10 Hz 0.2 µV p-p
Current Noise f = 1 kHz 80 fA/√Hz
Current Noise, Peak to Peak f = 0.1 Hz to 10 Hz 5 pA p-p
Small Signal −3 dB Bandwidth 1.5 MHz
Slew Rate ΔVISMEA = 10 V 5 V/µs
VOLTAGE SENSE DIFFERENCE AMPLIFER
Internal Fixed Gains 0.8 V/V
Gain Error VIN = ±10 V ±0.1 %
Gain Drift
T
A
= T
MIN
to T
MAX
3
Gain Nonlinearity VBVMEA = ±10 V, RL = 2 kΩ 3 ppm
Offset Voltage (RTO) BVREFH and BVREFL pins grounded 500 µV
Offset Voltage Drift TA = TMIN to TMAX 4 µV/°C
Differential Input Voltage Range VBVN = 0 V, VBVREFL = 0 V −16 +16 V
Input Common-Mode Voltage Range VBVMEA = 0 V −27 +27 V
Differential Input Impedance 200 kΩ
Input Common-Mode Impedance 90 kΩ
Output Voltage Swing AVEE + 1.5 AVCC − 1.5 V
Over Temperature TA = TMIN to TMAX AVEE + 1.7 AVCC − 1.7 V
Capacitive Load Drive 1000 pF
Short-Circuit Current
30
Rev. 0 | Page 3 of 32
AD8451 Data Sheet
Parameter Test Conditions/Comments Min Typ Max Unit
Reference Input Voltage Range BVREFH and BVREFL pins tied together AVEE AVCC V
Output Voltage Level Shift BVREFL pin grounded
Maximum BVREFH pin connected to VREF pin 4.5 5 5.5 mV
Scale Factor VBVMEA/VBVREFH 1.8 2 2.2 mV/V
CMRR
ΔV
CM
= 10 V, RTO
80
Temperature Coefficient TA = TMIN to TMAX 0.05 µV/V/°C
PSRR ΔVS = 20 V, RTO 100 dB
Output Voltage Noise f = 1 kHz, RTI 105 nV/√Hz
Voltage Noise, Peak to Peak f = 0.1 Hz to 10 Hz, RTI 2 µV p-p
Small Signal −3 dB Bandwidth 1 MHz
Slew Rate 0.8 V/µs
CONSTANT CURRENT AND CONSTANT VOLTAGE
LOOP FILTER AMPLIFIERS
Offset Voltage 150 µV
Offset Voltage Drift TA = TMIN to TMAX 0.6 µV/°C
Input Bias Current −5 +5 nA
Over Temperature TA = TMIN to TMAX −5 +5 nA
Input Common-Mode Voltage Range AVEE + 1.5 AVCC − 1.8 V
Output Voltage Swing VVCLN = AVEE + 1 V, VVCLP = AVCC − 1 V AVEE + 1.5 AVCC − 1 V
Over Temperature TA = TMIN to TMAX AVEE + 1.7 AVCC − 1 V
Closed-Loop Output Impedance 0.01 Ω
Capacitive Load Drive 1000 pF
Source Short-Circuit Current 1 mA
Sink Short-Circuit Current 40 mA
Open-Loop Gain
140
CMRR ΔVCM = 10 V 100 dB
PSRR ΔVS = 20 V 100 dB
Voltage Noise f = 1 kHz 10 nV/√Hz
Voltage Noise, Peak to Peak f = 0.1 Hz to 10 Hz 0.3 µV p-p
Current Noise f = 1 kHz 80 fA/√Hz
Current Noise, Peak to Peak f = 0.1 Hz to 10 Hz 5 pA p-p
Small Signal Gain Bandwidth Product 3 MHz
Slew Rate ΔVVINT = 10 V 1 V/µs
CC to CV Transition Time 1.5 µs
VINT AND CONSTANT VOLTAGE BUFFER
Nominal Gain 1 V/V
Offset Voltage 150 µV
Offset Voltage Drift TA = TMIN to TMAX 0.6 µV/°C
Input Bias Current
CV buffer only
−5
+5
Over Temperature TA = TMIN to TMAX −5 +5 nA
Input Voltage Range AVEE + 1.5 AVCC − 1.8 V
Output Voltage Swing
Current Sharing and Constant Voltage Buffers AVEE + 1.5 AVCC − 1.5 V
Over Temperature TA = TMIN to TMAX AVEE + 1.7 AVCC − 1.5 V
VINT Buffer VVCLN − 0.6 VVCLP + 0.6 V
Over Temperature TA = TMIN to TMAX VVCLN − 0.6 VVCLP + 0.6 V
Output Clamps Voltage Range VINT buffer only
VCLP Pin VVCLN AVCC − 1 V
VCLN Pin AVEE + 1 VVCLP V
Closed-Loop Output Impedance 1 Ω
Capacitive Load Drive 1000 pF
Short-Circuit Current 40 mA
PSRR ΔVS = 20 V 100 dB
Rev. 0 | Page 4 of 32
Data Sheet AD8451
Parameter Test Conditions/Comments Min Typ Max Unit
Voltage Noise f = 1 kHz 10 nV/√Hz
Voltage Noise, Peak to Peak f = 0.1 Hz to 10 Hz 0.3 µV p-p
Current Noise f = 1 kHz, CV buffer only 80 fA/√Hz
Current Noise, Peak to Peak f = 0.1 Hz to 10 Hz 5 pA p-p
Small Signal −3 dB Bandwidth
3
Slew Rate ΔVOUT = 10 V 1 V/µs
VOLTAGE REFERENCE
Nominal Output Voltage With respect to AGND 2.5 V
Output Voltage Error ±1 %
Temperature Drift TA = TMIN to TMAX 10 ppm/°C
Line Regulation ΔVS = 10 V 40 ppm/V
Load Regulation ΔIVREF = 1 mA (source only) 400 ppm/mA
Output Current, Sourcing 10 mA
Voltage Noise
f = 1 kHz
100
Voltage Noise, Peak to Peak f = 0.1 Hz to 10 Hz 5 µV p-p
DIGITAL INTERFACE, MODE INPUT
MODE pin (Pin 39)
Input Voltage High, VIH With respect to DGND 2.0 DVCC V
Input Voltage Low, VIL With respect to DGND DGND 0.8 V
Mode Switching Time 500 ns
POWER SUPPLY
Operating Voltage Range
AVCC 5 36 V
AVEE −31 0 V
Analog Supply Range AVCC − AVEE 5 36 V
DVCC
3
5
Quiescent Current
AVCC 7 10 mA
AVEE 6.5 10 mA
DVCC 40 70 µA
TEMPERATURE RANGE
For Specified Performance −40 +85 °C
Operational −55 +125 °C
Rev. 0 | Page 5 of 32
AD8451 Data Sheet
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter Rating
Analog Supply Voltage (AVCC − AVEE) 36 V
Digital Supply Voltage (DVCC − DGND)
36 V
Maximum Voltage at Any Input Pin AVCC
Minimum Voltage at Any Input Pin AVEE
Operating Temperature Range −40°C to +85°C
Storage Temperature Range −65°C to +150°C
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
THERMAL RESISTANCE
The θJA value assumes a 4-layer JEDEC standard board with
zero airflow.
Table 3. Thermal Resistance
Package Type θJA Unit
80-Lead LQFP 54.7 °C/W
ESD CAUTION
Rev. 0 | Page 6 of 32
Data Sheet AD8451
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
VCTRL
VCLN
AVCC
VVE1
NC
VINT
VCLP
VVE0
NC
VVP0
VSET
NC
DVCC
NC
DGND
NC
NC
VREF
NC
VSETBF
NC = NO CONNECT. DO NOT CO NNE CT TO THIS PIN.
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
NC
NC
NC
ISREFL
ISREFLS
AGND
ISREFH
VREF
AVEE
ISMEA
AVCC
NC
ISREFB
ISET
NC
IVE0
IVE1
NC
VINT
AVEE
BVPS
NC
NC
BVP
NC
BVREFH
AGND
BVREFL
BVREFLS
NC
BVN
NC
BVNS
NC
BVMEA
AVCC
MODE
NC
VREF
AVEE
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
AD8451
TOP VIEW
2
3
4
7
6
5
1
8
9
10
12
13
14
15
16
17
18
19
20
11
59
58
57
54
55
56
60
53
52
51
49
48
47
46
45
44
43
42
41
50
ISVP
RGP
NC
NC
NC
NC
NC
NC
NC
NC
NC
RGN
ISVN
NC
NC
NC
NC
NC
NC
NC
PIN 1
INDENTFIER
12137-002
Figure 2. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
Mnemonic
Input/Output
1
Description
1, 20 ISVP, ISVN Input Current Sense Instrumentation Amplifier Positive (Noninverting) and Negative
(Inverting) Inputs. Connect these pins across the current sense shunt resistor.
2, 19 RGP, RGN N/A Negative Input of the Preamplifiers of the Current Sense Instrumentation
Amplifier.
3 to 18, 21, 23, 25, 31, 33,
34, 40, 41, 43, 44, 46, 48,
52, 55, 63, 66, 69, 78 to 80
NC N/A No Connect. Do not connect to this pin.
22, 35 BVPS, BVNS Input Kelvin Sense Pins for the BVP and BVN Voltage Sense Difference Amplifier Inputs.
24, 32 BVP, BVN Input Voltage Sense Difference Amplifier Inputs.
26, 42, 73 VREF Output Voltage Reference Output Pins. VREF = 2.5 V.
27 BVREFH Input Reference Input for the Voltage Sense Difference Amplifier. To level shift the
voltage sense difference amplifier output by approximately 5 mV, connect this
pin to the VREF pin. Otherwise, connect this pin to the BVREFL pin.
28, 75 AGND N/A Analog Ground Pins.
29 BVREFL Input Reference Input for the Voltage Sense Difference Amplifier. The default connection
is to ground.
30 BVREFLS Input Kelvin Sense Pin for the BVREFL Pin.
Rev. 0 | Page 7 of 32
AD8451 Data Sheet
Pin No. Mnemonic Input/Output1 Description
36, 61, 72 AVEE N/A Analog Negative Supply Pins. The default voltage is −15 V.
37 BVMEA Output Voltage Sense Difference Amplifier Output.
38, 57, 70 AVCC N/A Analog Positive Supply Pins. The default voltage is 15 V.
39 MODE Input TTL Compliant Logic Input Selects Charge or Discharge Mode. Low =
discharge, high = charge.
45 DGND N/A Digital Ground Pin.
47 DVCC N/A Digital Supply. The default voltage is 5 V.
49 VSET Input Target Voltage for the Voltage Sense Control Loop.
50 VSETBF Output Buffered Voltage VSET.
51 VVP0 Input Noninverting Input of the Voltage Sense Integrator for Discharge Mode.
53
VVE0
Input
Inverting Input Voltage for the Voltage Sense Integrator for Discharge Mode.
54 VVE1 Input Inverting Input of the Voltage Sense Integrator for Charge Mode.
56, 62 VINT Output Minimum Output of the Voltage Sense and Current Sense Integrator Amplifiers.
58 VCLN Input Low Clamp Voltage for VCTRL.
59 VCTRL Output Controller Output Voltage. Connect this pin to the input of the PWM controller
(for example, the COMP pin of the ADP1972).
60 VCLP Input High Clamp Voltage for VCTRL.
64 IVE1 Input Inverting Input of the Current Sense Integrator for Charge Mode.
65 IVE0 Input Inverting Input of the Current Sense Integrator for Discharge Mode.
67 ISET Input Target Voltage for the Current Sense Control Loop.
68 ISREFB Output Buffered Voltage ISREFL.
71
ISMEA
Output
Current Sense Instrumentation Amplifier Output.
74 ISREFH Input Reference Input for the Current Sense Amplifier. To level shift the current sense
instrumentation amplifier output by approximately 20 mV, connect this pin to
the VREF pin. Otherwise, connect this pin to the ISREFL pin.
76 ISREFL Input Reference Input for the Current Sense Amplifier. The default connection is to
ground.
77 ISREFLS Input Kelvin Sense Pin for the ISREFL Pin.
1 N/A means not applicable.
Rev. 0 | Page 8 of 32
Data Sheet AD8451
TYPICAL PERFORMANCE CHARACTERISTICS
AVCC = +15 V, AVEE = −15 V, TA = 25°C, and RL = ∞, unless otherwise noted.
IA CHARACTERISTICS
15
OUTPUT VOLTAGE (V) 300 20
25
20
25
10
30
0
5
−5
−5
−10−10
15
10
5
AVCC = + 25V
AVEE = −5V
INPUT COMMON-MODE VOLTAGE (V)
12137-003
Figure 3. Input Common-Mode Voltage vs. Output Voltage
for AVCC = +25 V and AVEE = −5 V
15
–15
–10
–5
0
5
10
–35–30–10–20 0 4530 402010–25 –5–15 5 352515
INPUT CURRENT (mA)
INPUT VOLTAGE (V)
AVCC = +25V
AVEE = –5V
12137-004
Figure 4. Input Overvoltage Performance
for AVCC = +25 V and AVEE = −5 V
17.0
16.8
16.6
16.4
16.2
16.0
15.8
15.6
15.4
15.2
15.0
–15 –10 –5 0510 15 20 25
INPUT BI AS CURRE NT (n A)
INPUT COMMON-MODE VOLTAGE (V)
AVCC = + 15V
AVE E = –15V
AVCC = + 25V
AVEE = –5V
12137-005
Figure 5. Input Bias Current vs. Input Common-Mode Voltage
20
–20
–15
–10
–5
0
5
10
15
–20 –15 –10 –5 0 5 10 15 20
INPUT COMMON-MODE VOLTAGE (V)
OUTPUT VOLTAGE (V)
AVCC = +15V
AVEE = –15V
12137-006
Figure 6. Input Common-Mode Voltage vs. Output Voltage
for AVCC = +15 V and AVEE = −15 V
15
–15
–10
–5
0
5
10
–45 –35–40 –30 –10–20 04530 40
20
10
–25 –5–15 5352515
INPUT CURRENT (mA)
INPUT VOLTAGE (V)
AVCC = + 15V
AVE E = –15V
12137-007
Figure 7. Input Overvoltage Performance
for AVCC = +15 V and AVEE = −15 V
20
19
18
17
16
15
14
13
12
–40 –30 –20 –10 010 20 30 40 50 60 70 80 90
INPUT BI AS CURRE NT (n A)
TEMPERAT URE ( °C)
–IB
+IB
12137-008
Figure 8. Input Bias Current vs. Temperature
Rev. 0 | Page 9 of 32
AD8451 Data Sheet
20
–100
–80
–60
–40
–20
0
–40 –30 –20 –100 1020 30 40 5060 70 80 90
GAI N E RROR (µ V /V)
TEMPERAT URE ( °C)
12137-009
Figure 9. Gain Error vs. Temperature
0.3
–0.3
–0.2
–0.1
0
0.1
0.2
–40 –30 –20 –10 0 10 20 30 40 50 60 70 80 90
CMRR (µV/V)
TEMPERATURE (°C)
AVCC = +25V
AVEE = –5V
12137-010
Figure 10. Normalized CMRR vs. Temperature
GAIN(dB)
1M
FREQUENCY (Hz)
100k10k 10M100
20
40
10
30
50
1k
0
−20
−10
AVCC = + 15V
AVEE = −15V
12137-011
Figure 11. Gain vs. Frequency
160
50
60
70
80
90
100
110
120
130
140
150
0.1 1 10 100100k10k1k
CMRR (dB)
FREQUENCY (Hz)
12137-012
Figure 12. CMRR vs. Frequency
160
0
60
40
20
80
100
120
140
110 100 1M100k10k
1k
PSRR (dB)
FREQUENCY (Hz)
AVEE
AVCC
12137-013
Figure 13. PSRR vs. Frequency
100
1
10
0.1 1 10 100100k10k1k
SPECTRALDENSITYVOLTAGE NOISE (nV/√Hz)
FREQUENCY (Hz)
RTI
12137-014
Figure 14. Spectral Density Voltage Noise, RTI vs. Frequency
Rev. 0 | Page 10 of 32
Data Sheet AD8451
DA CHARACTERISTICS
60
–40
–30
–20
–10
0
10
20
30
40
50
–10 –5 0 5 10 15 20 25 30
INPUT COMMON-MODE VOLTAGE (V)
OUTPUT VOLTAGE (V)
12137-015
AVCC = + 25V
AVEE = −5V
Figure 15. Input Common-Mode Voltage vs. Output Voltage
for AVCC = +25 V and AVEE = −5 V
0
–50
–40
–30
–20
–10
100 1k 10k 100k 1M
VALID FORALL RATED
SUPPLY VOLTAGES
GAI N (dB)
FREQUENCY (Hz)
12137-016
Figure 16. Gain vs. Frequency
0
–120
–100
–80
–60
–40
–20
100 1k 10k 100k 1M
CMRR (dB)
FREQUENCY (Hz)
VALID FORALL RATED
SUPPLY VOLTAGES
12137-017
Figure 17. CMRR vs. Frequency
50
–50
–40
–30
–20
–10
0
10
20
30
40
–20 –15 –10 –5 0510 15 20
INPUT COMMON-MODE VOLTAGE (V)
OUTPUT VOLTAGE (V)
12137-018
AVCC = + 15V
AVEE = −15V
Figure 18. Input Common-Mode Voltage vs. Output Voltage
for AVCC = +15 V and AVEE = −15 V
50
–200
–150
–100
–50
0
–40 –30 –20 –10 010 20 30 40 50 60 70 80 90
GAI N E RROR (ppm)
TEMPERAT URE ( °C)
12137-019
Figure 19. Gain Error vs. Temperature
3
–3
–2
–1
0
1
2
–40 –30 –20 –10 010 20 30 40 50 60 70 80 90
CMRR (µV/V)
TEMPERAT URE ( °C)
12137-020
Figure 20. Normalized CMRR vs. Temperature
Rev. 0 | Page 11 of 32
AD8451 Data Sheet
0
–140
–120
–100
–80
–60
–40
–20
10 100 100k
10k
1k
FREQUENCY (Hz)
PSRR (dB)
VALID FORALL RATED
SUPPLY VOLTAGES
AVEE
AVCC
12137-021
Figure 21. PSRR vs. Frequency
1k
10
100
0.1 110 100 100k
10k1k
SPECTRAL DENSIT Y VOLTAGE NOISE (nV/√Hz)
FREQUENCY (Hz)
RTI
12137-022
Figure 22. Spectral Density Voltage Noise, RTI vs. Frequency
Rev. 0 | Page 12 of 32
Data Sheet AD8451
CC AND CV LOOP FILTER AMPLIFIERS, AND VSET BUFFER
500
–500
–400
–300
–200
–100
0
100
200
300
400
–15 –10 –5 0 5 10 15 20 25
INPUT OFFSET VOLTAGE (µV)
INPUT COMMON-MODE VOLT AGE (V)
AVCC = +25V
AVEE = –5V
AVCC = +15V
AVEE = –15V
12137-023
Figure 23. Input Offset Voltage vs. Input Common-Mode Voltage
for Two Supply Voltage Combinations
100
0
10
20
30
40
50
60
70
80
90
–15 –10 –5 0 5 10 15 20 25
INPUT BI AS CURRE NT (p A)
INPUT COMMON-MODE VOLT AGE (V)
AVCC = +25V
AVEE = –5V
AVCC = +15V
AVEE = –15V
12137-024
Figure 24. Input Bias Current vs. Input Common-Mode Voltage
for Two Supply Voltage Combinations
100
–40
–20
0
20
40
60
80
–40 –30 –20 –10 010 20 30 40 50 60 70 80 90
INPUT BI AS CURRE NT (n A)
TEMPERATURE (°C)
–IB
+IB
12137-025
Figure 25. Input Bias Current vs. Temperature
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
–40 –30 –20 –10 010 20 30 40 50 60 70 80 90
OUTPUT S OURCE CURRENT (mA)
TEMPERATURE (°C)
CONSTANT CURRE NT LOO P AND
CONSTANT VOLTAGE LOOP AMPLIFIERS
AVCC = +25V
AVEE = –5V
AVCC = +15V
AVEE = –15V
12137-026
Figure 26. Output Source Current vs. Temperature
for Two Supply Voltage Combinations
120
–40
–20
0
20
40
60
80
100
–45.0
–225.0
–202.5
–180.0
–157.5
–135.0
–112.5
–90.0
–67.5
10 100 1k 10k 100k 1M 10M
OPEN-LOOP GAIN (dB)
PHASE ( Degrees)
FRE Q UE NCY ( Hz )
PHASE
GAIN
12137-027
Figure 27. Open-Loop Gain and Phase vs. Frequency
160
0
20
40
60
80
100
120
140
10 100 1k 10k 100k 1M
CMRR (dB)
FRE Q UE NCY ( Hz )
CONSTANT CURRENT LO OP
AND
CONSTANT VOLTAGE
LOOP FILTER
AMPLIFIERS
12137-028
Figure 28. CMRR vs. Frequency
Rev. 0 | Page 13 of 32
AD8451 Data Sheet
140
0
20
40
60
80
100
120
10 100 1k 10k 100k 1M
PSRR (dB)
FRE Q UE NCY ( Hz )
+PSRR
–PSRR
12137-029
Figure 29. PSRR vs. Frequency
1k
1
10
100
0.1 110 100 100k
10k1k
SPECTRAL DENSITY VOLTAGE NOISE (nV/√Hz)
FRE Q UE NCY ( Hz )
12137-030
Figure 30. Range of Spectral Density Voltage Noise vs. Frequency
for the Op Amps and Buffers
1.5
–1.5
–0.5
0.5
1.0
–1.0
0
–15 353025
2015
10
50
–5–10
OUTPUT VOLTAGE (V)
TIME (µs)
TRANSITION
AVCC = +15V
AVEE = –15V
ISET
VCTRL
12137-031
Figure 31. CC to CV Transition
Rev. 0 | Page 14 of 32
Data Sheet AD8451
VINT BUFFER
0.5
–0.5
–0.4
–0.3
–0.2
–0.1
0
0.1
0.2
0.3
0.4
–40 –30 –20 –10 010 20 30 40 50 60 70 80 90
OUTPUT VOLTAGE SWING (V)
TEMPERATURE (°C)
VCTRL OUTPUT WITH RESPECT TO VCLP
VCTRL OUTPUT WITH RESPECT TO VCLN
VCL P AND V CLN REFERENCE
VALID FOR ALL RATED
SUPPLY VOLT AGES
12137-032
Figure 32. Output Voltage Swing with Respect to VCLP and VCLN
vs. Temperature
15
–15
–10
–5
0
5
10
100 1M100k10k1k
LOAD RESISTANCE (Ω)
OUTPUT VOLTAGE SWING (V)
12137-033
TE M P = –40°C
TEMP = +25°C
TEMP = +85°C
VCLP
VCLN
Figure 33. Output Voltage Swing vs. Load Resistance at Three Temperatures
6
–1
0
1
2
3
4
5
10 4035
30252015
OUTPUT CURRE NT (mA)
CLAMPED OUTPUT VOLTAGE (V)
VCLP
VCLN
V
IN
= +6V/–1V TE M P = –40°C
TEMP = 0°C
TEMP = +25°C
TEMP = +85°C
12137-034
Figure 34. Clamped Output Voltage vs. Output Current
at Four Temperatures
6
–1
0
1
2
3
4
5
0403530252015105
TIME (µs)
OUTPUT VOLTAGE (V)
CL = 100pF
RL = 2kΩ
12137-035
Figure 35. Large Signal Transient Response, RL = 2 kΩ, CL = 100 pF
0.20
0.15
–0.20
–0.15
–0.10
–0.05
0
0.05
0.10
010987654
321
TIME (µs)
OUTPUT VOLTAGE (V)
C
L
= 10pF
C
L
= 100pF
C
L
= 510pF
C
L
= 680pF
C
L
= 1000pF
12137-036
Figure 36. Small Signal Transient Response vs. Capacitive Load
100
10
1
0.110 100 1k 10k 100k 1M
OUTPUT IMPEDANCE (Ω)
FRE Q UE NCY ( Hz )
12137-037
Figure 37. Output Impedance vs. Frequency
Rev. 0 | Page 15 of 32
AD8451 Data Sheet
REFERENCE CHARACTERISTICS
2.51
2.50
2.49
2.48
2.47
2.46 012345678910
OUTPUT VOLTAGE (V)
OUTPUT CURRE NT—SOURCI NG (mA)
T
A
= –40° C
T
A
= +25°C
T
A
= –20° C
T
A
= +85°C
T
A
= 0° C
AVCC = +25V
AVEE = –5V
12137-038
Figure 38. Output Voltage vs. Output Current (Sourcing) over Temperature
2.9
2.8
2.7
2.6
2.5
2.4
–10 –9 –8 –7 –6 –5 –4 –3 –2 –1 0
OUTPUT VOLTAGE (V)
OUTPUT CURRE NT—SINKI NG (mA)
T
A
= +85°C
T
A
= +25°C
T
A
= 0° C
T
A
= –20° C
T
A
= –40° C
AVCC = +25V
AVEE = –5V
12137-039
Figure 39. Output Voltage vs. Output Current (Sinking) over Temperature
1200
1100
1000
900
800
700
600
–40 –30 –20 –10 010 20 30 40 50 60 70 80 90
LOAD REGULATION (ppm/mA)
TEMPERATURE (°C)
AVCC = +25V
AVEE = –5V
12137-040
Figure 40. Source and Sink Load Regulation vs. Temperature
1k
10
100
0.1 110 100 100k
10k1k
SPECTRAL DENSITY VOLTAGE NOISE (nV/√Hz)
FRE Q UE NCY ( Hz )
12137-041
Figure 41. Spectral Density Voltage Noise vs. Frequency
Rev. 0 | Page 16 of 32
Data Sheet AD8451
THEORY OF OPERATION
OVERVIEW
To form and test a battery, the battery must undergo charge and
discharge cycles. During these cycles, the battery terminal current
and voltage must be precisely controlled to prevent battery failure
or a reduction in the capacity of the battery. Therefore, battery
formation and test systems require a high precision analog front
end to monitor the battery current and terminal voltage. The
analog front end of the AD8451 includes a precision current
sense fixed gain instrumentation amplifier (IA) to measure the
battery current and a precision voltage sense fixed gain difference
amplifier (DA) to measure the battery voltage.
Battery formation and test systems charge and discharge batteries
using a constant current/constant voltage (CC/CV) algorithm. In
other words, the system first forces a set constant current into
or out of the battery until the battery voltage reaches a target
value. At this point, a set constant voltage is forced across the
battery terminals.
The AD8451 provides two control loops—CC loop and a CV
loop—that transition automatically after the battery reaches the
user defined target voltage. These loops are implemented via two
precision specialty amplifiers with external feedback networks
that set the transfer function of the CC and CV loops.
Moreover, in the AD8451, these loops reconfigure themselves to
charge or discharge the battery by toggling the MODE pin.
Figure 42 is a block diagram of the AD8451 that illustrates
the distinct sections of the AD8451, including the IA and DA
measurement blocks, and the loop filter amplifiers. Figure 43 is a
block diagram of a battery formation and test system.
17
18
15
16
8
7
6
5
4
3
2
14
13
9
12
11
10
ISVP
MODE
MODE
RGP
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
RGN
ISVN
NC
19
34 35272524232221 3332313029
59
54
56
60
53
51
49
44
43
41
50
58
46
39
–
+
–
+
–
+
–
+
–
+
AVEE
AVEE
1×
1×
1
20
42
37 40
26 28 36 38
57
55
52
47
48
45
NC
ISREFH
NC
VREF
ISREFLS
ISREFL
NC
IVE1
ISMEA
IVE0
ISET
VINT
ISREFB
NC
NC
AGND
AVEE
AVCC
NC
AVEE
VCTRL
VCLN
VVE1
VINT
VCLP
VVE0
VVP0
VSET
NC
NC
NC
NC
VSETBF
VREF
AVCC
AVCC
NC
NC
DVCC
NC
DGND
64 6269 6568 6773 7178 7477 7680 79 6163707275 66
BVREFH
BVPS
NC
BVREFL
BVP
NC
NC
BVNS
BVREFLS
NC
NC
NC
BVMEA
BVN
NC
MODE
VREF
AGND
AVEE
AVCC
VINT
BUFFER
VSET
BUFFER
10kΩ
20kΩ
19.2kΩ
100kΩ
100Ω
80kΩ
79.9kΩ
NC
+/–
+/–
NC
50kΩ
100kΩ
10kΩ
1667Ω
806Ω
100kΩ
10kΩ
10kΩ
CV LO O P
FILTER
AMPLIFIER
CC LO O P
FILTER
AMPLIFIER
BATTERY
CURRENT
SENSING I A
BATTERY
VOLTAGE
SENSING
DA
CONSTANT
CURRENT AND
VOLTAGE LOOP
FILTER AMPLIFIERS
–
+
AD8451
1.1mA
2.5V
VREF ISREFL
BUFFER
1×
12137-042
Figure 42. Detailed Block Diagram
Rev. 0 | Page 17 of 32
AD8451 Data Sheet
BATTERY
VCTRL
SENSE
RESISTOR
ISVP
ISVN
BVP
BVN
MODE
SWITCHES
(3)
BATTERY
CURRENT
AVEE
CV
BUFFER
CONSTANT
CURRENT LO OP
FILTER AMPLIFIER
–
+
–
+
1×
VINT
BUFFER
VSETBF
VSET
ISET
V1
V2 CD C D C D
VINT
ISMEA
BVMEA
VVE1
VVE0
VVP0
IVE1
IVE0
DA
–
+
–
+
IA
AD8451
CONTROLLER
1×
SET
BATTERY
VOLTAGE
SET
BATTERY
CURRENT
EXTERNAL
PASSIVE
COMPENSATION
NETWORK
C = CHARGE
D = DIS CHARGE
CONSTANT
VOLTAGE LOOP
FILTER AMPLIFIER
POWER CONVERTER
SW ITCHE D OR LINEAR
SYSTEM LOOP COMPENSATION
12137-043
Figure 43. Signal Path of an Li-Ion Battery Formation and Test System Using the AD8451
INSTRUMENTATION AMPLIFIER (IA)
Figure 44 is a block diagram of the IA, which is used to monitor the
battery current. The architecture of the IA is the classic 3-op-amp
topology, similar to the Analog Devices industry-standard
AD8221 and AD620, with a fixed gain of 26. This architecture
provides the highest achievable CMRR at a given gain, enabling
high-side battery current sensing without the introduction of
significant errors in the measurement. For more information
about instrumentation amplifiers, see A Designer's Guide to
Instrumentation Amplifiers.
Reversing Polarity When Charging and Discharging
Figure 43 shows that during the charge cycle, the power converter
feeds current into the battery, generating a positive voltage across
the current sense resistor. During the discharge cycle, the power
converter draws current from the battery, generating a negative
voltage across the sense resistor. In other words, the battery current
polarity reverses when the battery discharges.
In the CC control loop, this change in polarity can be problematic
if the polarity of the target current is not reversed. To solve this
problem, the AD8451 IA includes a multiplexer preceding its
inputs that inverts the polarity of the IA gain. This multiplexer
is controlled via the MODE pin. When the MODE pin is logic
high (charge mode), the IA gain is noninverting, and when the
MODE pin is logic low (discharge mode), the IA gain is
inverting.
10kΩ
20kΩ
806Ω
IA
RGP
RGN
ISVN
ISVP
+CURRENT
SHUNT
–CURRENT
SHUNT
ISMEA
–
+
G = 2 S UBTRACTOR
100kΩ
19.2kΩ
ISREFH
ISREFL
VREF
POLARITY
INVERTER
POLARITY
INVERTER
MODE
–
+
–
+
10kΩ
10kΩ
10kΩ
1667Ω
±
±
12137-044
Figure 44. IA Simplified Block Diagram
IA Offset Option
As shown in Figure 44, the IA reference node is connected to
the ISREFL and ISREFH pins via an internal resistor divider.
This resistor divider can be used to introduce a temperature
insensitive offset to the output of the IA such that it always
reads a voltage higher than zero for a zero differential input.
Because the output voltage of the IA is always positive, a
unipolar analog-to-digital converter (ADC) can digitize it.
Rev. 0 | Page 18 of 32
Data Sheet AD8451
When the ISREFH pin is tied to the VREF pin with the ISREFL
pin grounded, the voltage at the ISMEA pin is increased by 20 m V,
guaranteeing that the output of the IA is always positive for zero
differential inputs. Other voltage shifts can be realized by tying
the ISREFH pin to an external voltage source. The gain from the
ISREFH pin to the ISMEA pin is 8 m V / V. For zero offset, tie
the ISREFL and ISREFH pins to ground.
Battery Reversal and Overvoltage Protection
The AD8451 IA can be configured for high-side or low-side
current sensing. If the IA is configured for high-side current
sensing (see Figure 43) and the battery is connected backward,
the IA inputs may be held at a voltage that is below the negative
power rail (AVEE), depending on the battery voltage.
To prevent damage to the IA under these conditions, the IA
inputs include overvoltage protection circuitry that allows them
to be held at voltages of up to 55 V from the opposite power
rail. In other words, the safe voltage span for the IA inputs
extends from AVCC − 55 V to AVEE + 55 V.
DIFFERENCE AMPLIFIER (DA)
Figure 45 is a block diagram of the DA, which is used to monitor
the battery voltage. The architecture of the DA is a subtractor
amplifier with a fixed gain of 0.8. This gain value allows the DA to
funnel the voltage of a 5 V battery to a level that can be read by
a 5 V ADC with a 4.096 V reference.
BVREFL
BVP
BVN 100kΩ
100kΩ 100kΩ
50kΩ
80kΩ
79.9kΩ
DA
–
+
BVREFH
VREF
BVMEA
12137-045
Figure 45. DA Simplified Block Diagram
The resistors that form the DA gain network are laser trimmed
to a matching level better than ±0.1%. This level of matching
minimizes the gain error and gain error drift of the DA while
maximizing the CMRR of the DA. This matching also allows
the controller to set a stable target voltage for the battery over
temperature while rejecting the ground bounce in the battery
negative terminal.
Like the IA, the DA can also level shift its output voltage via an
internal resistor divider that is tied to the DA reference node. This
resistor divider is connected to the BVREFH and BVREFL pins.
When the BVREFH pin is tied to the VREF pin with the BVREFL
pin grounded, the voltage at the BVMEA pin is increased by 5 m V,
guaranteeing that the output of the DA is always positive for
zero differential inputs. Other voltage shifts can be realized by
tying the BVREFH pin to an external voltage source. The gain
from the BVREFH pin to the BVMEA pin is 2 m V / V. For zero
offset, tie the BVREFL and BVREFH pins to ground.
CC AND CV LOOP FILTER AMPLIFIERS
The CC and CV loop filter amplifiers are high precision, low
noise specialty amplifiers with very low offset voltage and very
low input bias current. These amplifiers serve two purposes:
• Using external components, the amplifiers implement active
loop filters that set the dynamics (transfer function) of the
CC and CV loops.
• The amplifiers perform a seamless transition from CC to
CV mode after the battery reaches its target voltage.
Figure 46 is the functional block diagram of the AD8451 CC
and CV feedback loops for charge mode (MODE logic pin is high).
For illustration purposes, the external networks connected to
the loop amplifiers are simple RC networks configured to form
single-pole inverting integrators. The outputs of the CC and CV
loop filter amplifiers are coupled to the VINT pins via an analog
NOR circuit (minimum output selector circuit), such that they can
only pull the VINT node down. In other words, the loop amplifier
that requires the lowest voltage at the VINT pins is in control of
the node. Thus, only one loop amplifier, CC or CV, can be in
control of the system charging control loop at any given time.
Rev. 0 | Page 19 of 32
AD8451 Data Sheet
ISET
–
+
–
+
CC LOOP
AMPLIFIER
CV LOOP
AMPLIFIER
IVE1
VVE1
ANALOG
‘NOR’
ISVN
BVP
BVN GDA
–
+
–
+
GIA
ISMEAS
BVMEA
IBAT
IA
DA
V2 R2 C2
VSET
R1 C1
1× VCTRL
VCLN
VCLP
VINT
BUFFER
V1
VBAT
SENSE
RESISTOR
MODE
5V
–
+
RS
VINT
POWER
CONVERTER
VINT
IOUT
ISVP
VCTRL
CURRENT
POWER
BUS
MINIMUM
OUTPUT
SELECTOR
V4V3
V3 < VCTRL < V4
12137-046
Figure 46. Functional Block Diagram of the CC and CV Loops in Charge Mode (MODE Pin High)
The unity-gain amplifier (VINT buffer) buffers the VINT pins
and drives the VCTRL pin. The VCTRL pin is the control output
of the AD8451 and the control input of the power converter. The
VISET and VVSET voltage sources set the target constant current and
the target constant voltage, respectively. When the CC and CV
feedback loops are in a steady state, the charging current is set at
IBAT_SS =
S
IA
ISET
RG
V
×
where:
IBAT_SS = is the steady state charging current.
GIA is the IA gain.
RS is the value of the shunt resistor.
The target voltage is set at
VBAT_SS =
DA
VSET
G
V
where:
VBAT_SS = steady state battery voltage.
GDA is the DA gain.
Because the offset voltage of the loop amplifiers is in series with
the target voltage sources, VISET and VVSET, the high precision of
these amplifiers minimizes this source of error.
Figure 47 shows a typical CC/CV charging profile for a Li-Ion
battery. In the first stage of the charging process, the battery is
charged with a CC of 1 A. When the battery voltage reaches a
target voltage of 4.2 V, the charging process transitions such that
the battery is charged with a CV of 4.2 V.
The following steps describe how the AD8451 implements the
CC/CV charging profile (see Figure 46). In this scenario, the
battery begins in the fully discharged state, and the system has
just been turned on such that IBAT = 0 A at Time 0.
1. Because the voltages at the ISMEA and BVMEA pins
are less than the target voltages (VISET and VVSET) at Time 0,
both integrators begin to ramp, increasing the voltage at
the VINT node.
1.25
0
0.25
0.50
0.75
1.00
5
0
1
2
3
4
0 54321
CURRENT (A)
VOLTAGE (V)
TIME (Hours)
CC
CHARGE
BEGINS
TRANSITION FROM CC TO CV
CC
CHARGE
ENDS
12137-047
Figure 47. Representative Constant Current to Constant Voltage Transition
near the End of a Battery Charging Cycle
2. As the voltage at the VINT node increases, the voltage at
the VCRTL node rises, and the output current of the power
converter, IBAT, increases (assuming that an increasing voltage
at the VCRTL node increases the output current of the
power converter).
3. When the IBAT current reaches the CC steady state value,
IBAT_SS, the battery voltage is still less than the target steady
state value, VBAT_SS. Therefore, the CV loop tries to keep
pulling the VINT node up while the CC loop tries to keep
it at its current voltage. At this point, the voltage at the ISMEA
pin equals VISET; therefore, the CC loop stops integrating.
4. Because the loop amplifiers can only pull the VINT node
down due to the analog NOR circuit, the CC loop takes
control of the charging feedback loop, and the CV loop is
disabled.
5. As the charging process continues, the battery voltage
increases until it reaches the steady state value, VBAT_SS, and
the voltage at the BVMEA pin reaches the target voltage, VVSET.
Rev. 0 | Page 20 of 32
Data Sheet AD8451
6. The CV loop tries to pull the VINT node down to reduce
the charging current (IBAT) and prevent the battery voltage
from rising any further. At the same time, the CC loop tries
to keep the VINT node at its current voltage to keep the
battery current at IBAT_SS.
7. Because the loop amplifiers can only pull the VINT node
down due to the analog NOR circuit, the CV loop takes
control of the charging feedback loop, and the CC loop is
disabled.
The analog NOR (minimum output selector) circuit that couples
the outputs of the loop amplifiers is optimized to minimize the
transition time from CC to CV control. Any delay in the transition
causes the CC loop to remain in control of the charge feedback
loop after the battery voltage reaches its target value. Therefore,
the battery voltage continues to rise beyond VBAT_SS until the
control loop transitions; that is, the battery voltage overshoots
its target voltage. When the CV loop takes control of the charge
feedback loop, it reduces the battery voltage to the target voltage.
A large overshoot in the battery voltage due to transition delays
can damage the battery; thus, it is crucial to minimize delays by
implementing a fast CC to CV transition.
Figure 48 is the functional block diagram of the AD8451 CC
and CV feedback loops for discharge mode (MODE logic pin is
low). In discharge mode, the feedback loops operate in a similar
manner as in charge mode. The only difference is in the CV
loop amplifier, which operates as a noninverting integrator in
discharge mode. For illustration purposes, the external networks
connected to the loop amplifiers are simple RC networks
configured to form single-pole integrators (see Figure 48).
Compensation
In battery formation and test systems, the CC and CV feedback
loops have significantly different open-loop gain and crossover
frequencies; therefore, each loop requires its own frequency
compensation. The active filter architecture of the AD8451 CC
and CV loops allows the frequency response of each loop to be
set independently via external components. Moreover, due to
the internal switches in the CC and CV amplifiers, the frequency
response of the loops in charge mode does not affect the
frequency response of the loops in discharge mode.
Unlike simpler controllers that use passive networks to ground
for frequency compensation, the AD8451 allows the use of
feedback networks for its CC and CV loop filter amplifiers.
These networks enable the implementation of both
proportional differentiator (PD) Type II and proportional
integrator differentiator (PID) Type III compensators. Note
that in charge mode, both the CC and CV loops implement
inverting compensators, whereas in discharge mode, the CC
loop implements an inverting compensator, and the CV loop
implements a noninverting compensator. As a result, the CV loop
in discharge mode includes an additional amplifier, VSET buffer, to
buffer the VSET node from the feedback network (see Figure 48).
VINT Buffer
The unity-gain amplifier (VINT buffer) is a clamp amplifier
that drives the VCTRL pin. The VCTRL pin is the control
output of the AD8451 and the control input of the power
converter (see Figure 46 and Figure 48). The output voltage
range of this amplifier is bounded by the clamp voltages at the
VCLP and VCLN pins such that
VVCLN − 0.5 V < VVCTRL < VVCLP + 0.5 V
The reduction in the output voltage range of the amplifier is a
safety feature that allows the AD8451 to drive devices such as
the ADP1972 PWM controller, whose input voltage range must
not exceed 5.5 V (that is, the voltage at the COMP pin of the
ADP1972 must be below 5.5 V).
MODE PIN, CHARGE AND DISCHARGE CONTROL
The MODE pin is a TTL logic input that configures the AD8451
for either charge or discharge mode. A logic low (VMODE < 0.8 V)
corresponds to discharge mode, and a logic high (VMODE > 2 V)
corresponds to charge mode. Internal to the AD8451, the MODE
pin toggles all single-pole, double throw (SPDT) switches in the
CC and CV loop amplifiers and inverts the gain polarity of the IA.
VSET
VSET
BUFFER
VSETBF
ISET
–
+
–
+
CC LOOP
AMPLIFIER
CV LOOP
AMPLIFIER
IVE0
VVE0
ANALOG
‘NOR’
ISVN
BVP
BVN G
DA
–
+
–
+
G
IA
ISMEAS
BVMEA
I
BAT
IA
DA
R2
R2
C2
VVP0
R1 C1
C
2
1× VCTRL
VCLN
VCLP
VINT
BUFFER
V1
V
BAT
SENSE
RESISTOR
MODE
–
+
R
S
VINT
VINT
ISVP
MINIMUM
OUTPUT
SELECTOR
V4V3
V3 < VCTRL < V4
V2
1×
12137-048
POWER
CONVERTER
IOUT
VCTRL
CURRENT
POWER
BUS
Figure 48. Functional Block Diagram of the CC and CV Loops in Discharge Mode (MODE Pin Low)
Rev. 0 | Page 21 of 32
AD8451 Data Sheet
APPLICATIONS INFORMATION
This section describes how to use the AD8451 in the context of
a battery formation and test system. This section includes a
design example of a small scale model of an actual system.
FUNCTIONAL DESCRIPTION
The AD8451 is a precision analog front end and controller for
battery formation and test systems. These systems use precision
controllers and power stages to put batteries through charge and
discharge cycles. Figure 49 shows the signal path of a simplified
switching battery formation and test system using the AD8451
controller and the ADP1972 PWM controller. For more
information on the ADP1972, see the ADP1972 data sheet.
The AD8451 is suitable for systems that form and test NiCad,
NiMH, and Li-Ion batteries and is designed to operate in
conjunction with both linear and switching power stages.
The AD8451 includes the following blocks (see Figure 42 and
the Theory of Operation section for more information).
• A fixed gain IA that senses low-side or high-side battery
current.
• A fixed gain DA that measures the terminal voltage of the
battery.
• Two loop filter error amplifiers that receive the battery target
current and voltage and establish the dynamics of the CC and
CV feedback loops.
• A minimum output selector circuit that combines the
outputs of the loop filter error amplifiers to perform
automatic CC to CV switching.
• An output clamp amplifier that drives the VCTRL pin. The
voltage range of this amplifier is limited by the voltage at
the VCLP and VCLN pins such that it cannot overrange
the subsequent stage. The output clamp amplifier can drive
switching and linear power converters. Note that an
increasing voltage at the VCTRL pin must translate to a
larger output current in the power converter.
• A 2.5 V reference whose output node is the VREF pin.
A logic input pin (MODE) that changes the configuration of the
controller from charge to discharge mode. A logic high at the
MODE pin configures charge mode; a logic low configures
discharge mode.
BATTERY
LEVEL
SHIFTER
VCTRL
SENSE
RESISTOR
ISVP
ISVN
BVP
BVN
MODE
SWITCHES
(3)
AVCC
OUTPUT
DRIVERS
BATTERY
CURRENT
AVEE
CV
BUFFER
CONSTANT
CURRENT LO OP
FILTER AMPLIFIER
–
+
–
+
1×
VINT
BUFFER
VSETBF
VSET
ISET
CD C D C D
VINT
ISMEA
BVMEA
VVE1
VVE0
VVP0
IVE1
IVE0
OUTPUT
FILTER
DA
–
+
–
+
IA
AD8451
CONTROLLER
1×
SET
BATTERY
VOLTAGE
SET
BATTERY
CURRENT
DC-TO - DC P OWE R CONVERTER
EXTERNAL
PASSIVE
COMPENSATION
NETWORK
C = CHARGE
D = DIS CHARGE
CONSTANT
VOLTAGE LOOP
FILTER AMPLIFIER
ADP1972
PWM
12137-049
Figure 49. Complete Signal Path of a Battery Test or Formation System Suitable for Li-Ion Batteries
Rev. 0 | Page 22 of 32
Data Sheet AD8451
POWER SUPPLY CONNECTIONS
The AD8451 requires two analog power supplies (AVCC and
AVEE), one digital power supply (DVCC), one analog ground
(AGND), and one digital ground (DGND). AVCC and AVEE
power all the analog blocks, including the IA, DA, and op amps,
and DVCC powers the MODE input logic. AGND provides a
reference and return path for the 2.5 V reference, and DGND
provides a reference and return path for the digital circuitry.
The rated absolute maximum value for AVCC − AVEE is 36 V,
and the minimum operating AVCC and AVEE voltages are +5 V
and −5 V, respectively. Due to the high PSRR of the AD8451
analog blocks, AVCC can be connected directly to the high current
power bus (the input voltage of the power converter) without
risking the injection of supply noise to the controller outputs.
A commonly used power supply combination is +15 V for
AVCC , −15 V for AVEE, and +5 V for DVCC. The +15 V rail
for AVCC provides enough headroom to the IA such that it can
be connected in a high-side current sensing configuration. The
−15 V rail for AVEE allows the DA to sense accidental reverse
battery conditions (see the Reverse Battery Conditions section).
Connect decoupling capacitors to all the supply pins. A 1 µF
capacitor in parallel with a 0.1 µF capacitor is recommended.
CURRENT SENSE IA CONNECTIONS
For a description of the IA, see the Theory of Operation section,
Figure 42, and Figure 44. The IA fixed gain is 26.
Current Sensors
Two common options for current sensors are isolated current
sensing transducers and shunt resistors. Isolated current sensing
transducers are galvanically isolated from the power converter
and are affected less by the high frequency noise generated by
switch mode power supplies. Shunt resistors are less expensive
and easier to deploy.
If a shunt resistor sensor is used, a 4-terminal, low resistance shunt
resistor is recommended. Two of the four terminals conduct the
battery current, whereas the other two terminals conduct virtually
no current. The terminals that conduct no current are sense
terminals that are used to measure the voltage drop across the
resistor (and, therefore, the current flowing through it) using an
amplifier such as the IA of the AD8451. To interface the IA with
the current sensor, connect the sense terminals of the sensor to
the ISVP and ISVN pins of the AD8451 (see Figure 50).
Optional Low-Pass Filter
The AD8451 is designed to control both linear regulators and
switching power converters. Linear regulators are generally
noise free, whereas switch mode power converters generate
switching noise. Connecting an external differential low-pass
filter between the current sensor and the IA inputs reduces the
injection of switching noise into the IA (see Figure 50).
ISVP
–
+10kΩ
20kΩ
20kΩ
10kΩ
LPF
RGP
4 TERMINA L
SHUNT
I
BAT
–
+
DUT
ISVN
RGN
+
–
10kΩ
10kΩ
1667Ω
12137-050
Figure 50. 4-Terminal Shunt Resistor Connected to the Current Sense IA
VOLTAGE SENSE DA CONNECTIONS
For a description of the DA, see the Theory of Operation
section, Figure 42, and Figure 45. The DA fixed gain is 0.8.
Reverse Battery Conditions
The output voltage of the AD8451 DA can be used to detect a
reverse battery connection. A −15 V rail for AVEE allows the
output of the DA to go below ground when the battery is
connected backward. Therefore, the condition can be detected
by monitoring the BVMEA pin for a negative voltage.
BATTERY CURRENT AND VOLTAGE CONTROL
INPUTS (ISET AND VSET)
The voltages at the ISET and VSET input pins set the target
battery current and voltage for the CC and CV loops. These
inputs must be driven by a precision voltage source (or a digital-
to-analog converter [DAC] connected to a precision reference)
whose output voltage is referenced to the same voltage as the IA
and DA reference pins (ISREFH/ISREFL and BVREFH/BVREFL,
respectively). For example, if the IA reference pins are connected
to AGND, the voltage source connected to ISET must also be
referenced to AGND. In the same way, if the DA reference pins
are connected to AGND, the voltage source connected to VSET
must also be referenced to AGND.
In constant current mode, when the CC feedback loop is in a
steady state, the ISET input sets the battery current as follows:
IBAT_SS =
SIA
ISET
RG
V
×
=
S
ISET
R
V
×26
where:
GIA is the IA gain.
RS is the value of the shunt resistor.
Rev. 0 | Page 23 of 32
AD8451 Data Sheet
In constant voltage mode, when the CV feedback loop is in
steady state, the VSET input sets the battery voltage as follows:
VBAT_SS =
DA
VSET
G
V
=
8.0
VSET
V
where GDA is the DA gain.
Therefore, the accuracy and temperature stability of the formation
and test system are not only dependent on the precision of the
AD8451, but also on the accuracy of the ISET and VSET inputs.
LOOP FILTER AMPLIFIERS
The AD8451 has two loop filter amplifiers, also known as error
amplifiers (see Figure 49). One amplifier is for constant current
control (CC loop filter amplifier), and the other amplifier is for
constant voltage control (CV loop filter amplifier). The outputs
of these amplifiers are combined using a minimum output
selector circuit to perform automatic CC to CV switching.
Table 5 lists the inputs of the loop filter amplifiers for charge
mode and discharge mode.
Table 5. Integrator Input Connections
Feedback Loop Function
Reference
Input
Feedback
Terminal
Control the Current While Discharging
a Battery
ISET IVE0
Control the Current While Charging
a Battery
ISET IVE1
Control the Voltage While Discharging
a Battery
VSET VVE0
Control the Voltage While Charging
a Battery
VSET VVE1
The CC and CV amplifiers in charge mode and the CC amplifier
in discharge mode are inverting integrators, whereas the CV
amplifier in discharge mode is a noninverting integrator. Therefore,
the CV amplifier in discharge mode uses an extra amplifier, the
VSET buffer, to buffer the VSET input pin (see Figure 42). In
addition, the CV amplifier in discharge mode uses the VVP0
pin to couple the signal from the BVMEA pin to the integrator.
CONNECTING TO A PWM CONTROLLER (VCTRL PIN)
The VCTRL output pin of the AD8451 is designed to interface
with linear power converters and with PWM controllers such as
the ADP1972. The voltage range of the VCTRL output pin is
bound by the voltages at the VCLP and VCLN pins, as follows:
VVCLN − 0.5 V < VVCTRL < VVCLP + 0.5 V
Because the maximum rated input voltage at the COMP pin of
the ADP1972 is 5.5 V, connect the clamp voltages of the output
amplifier to 5 V (VCLP) and ground (VCLN) to prevent over-
ranging of the COMP input. As an additional precaution, install
an external 5.1 V Zener diode from the COMP pin to ground
with a series 1 kΩ resistor connected between the VCTRL and
COMP pins. Consult the ADP1972 data sheet for additional
applications information.
Given the architecture of the AD8451, the controller requires
that an increasing voltage at the VCTRL pin translates to a
larger output current in the power converter. If this is not the
case, a unity-gain inverting amplifier can be added in series
with the AD8451 output to add an extra inversion.
STEP-BY-STEP DESIGN EXAMPLE
This section describes the systematic design of a 1 A battery
charger/discharger using the AD8451 controller and the
ADP1972 PWM controller. The power converter used in this
design is a nonisolated buck boost dc-to-dc converter. The target
battery is a 4.2 V fully charged, 2.7 V fully discharged Li-Ion
batter y.
Step 1: Design the Switching Power Converter
Select the switches and passive components of the buck boost
power converter to support the 1 A maximum battery current.
The design of the power converter is beyond the scope of this
data sheet; however, there are many application notes and other
helpful documents available from manufacturers of integrated
driver circuits and power MOSFET output devices that can be
used for reference.
Step 2: Identify the Control Voltage Range of the
ADP1972
The control voltage range of the ADP1972 (voltage range of the
COMP input pin) is 0.5 V to 4.5 V. An input voltage of 4.5 V
results in the highest duty cycle and output current, whereas an
input voltage of 0.5 V results in the lowest duty cycle and output
current. Because the COMP pin connects directly to the VCTRL
output pin of the AD8451, the battery current is proportional to
the voltage at the VCTRL pin.
For information about how to interface the ADP1972 to the
power converter switches, see the ADP1972 data sheet.
Step 3: Determine the Control Voltage for the CV Loop
The relationship between the control voltage for the CV loop
(the voltage at the VSET pin), the target battery voltage, and the
DA gain is as follows:
CV Battery Target Voltage =
8.0
VSET
DA
VSET
V
G
V=
In charge mode, for a CV battery target voltage of 4.2 V, select a
CV control voltage of 3.36 V. In discharge mode, for a CV
battery target voltage of 2.7 V, select a CV control voltage of
2.16 V.
Rev. 0 | Page 24 of 32
Data Sheet AD8451
Step 4: Determine the Control Voltage for the CC Loop
and the Shunt Resistor
The relationship between the control voltage for the CC loop
(the voltage at the ISET pin), the target battery current, and the
IA gain is as follows:
CC Battery Target Current =
S
ISET
SIA
ISET
R
V
R
G
V
×
=
×26
The voltage across the shunt resistor is as follows:
Shunt Resistor Voltage =
26
ISET
IA
ISET
V
G
V=
For target current of 1 A, choosing a 20 mΩ shunt resistor
results in a control voltage of 4 V.
When selecting a shunt resistor, consider the resistor style and
construction. For low power dissipation applications, many
temperature stable SMD styles can be soldered to a heat sink
pad on a printed circuit board (PCB). For optimum accuracy,
choose a shunt resistor that provides force and sense terminals.
In these resistors, the battery current flows through the force
terminals and the voltage drop in the resistor is read at the sense
terminals.
Step 5: Choose the Control Voltage Sources
The input control voltages (the voltages at the ISET and VSET
pins) can be generated by an analog voltage source such as a
voltage reference or by a DAC. In both cases, select a device that
provides a stable, low noise output voltage. If a DAC is preferred,
Analog Devices offers a wide range of precision converters. For
example, the AD5668 16-bit DAC provides up to eight 0 V to
4 V sources when connected to an external 2 V reference.
To maximize accuracy, the control voltage sources must be
referenced to the same potential as the outputs of the IA and
DA. For example, if the IA and DA reference pins are connected
to AGND, connect the reference pins of the control voltage
sources to AGND.
Step 6: Select the Compensation Devices
Feedback controlled switching power converters require
frequency compensation to guarantee loop stability. There are
many references available about how to design the compensation
for such power converters. The AD8451 provides active loop
filter error amplifiers for the CC and CV control loops that
can implement proportional integrator (PI), PD, and PID
compensators using external passive components.
Rev. 0 | Page 25 of 32
AD8451 Data Sheet
EVALUATION BOARD
INTRODUCTION
The AD8451-E VA L Z evaluation board is a convenient
standalone platform for evaluating the major elements of the
AD8451, either as a standalone component or connected to a
battery test/formation system.
In the latter configuration, the AD8451-E VA L Z operates just as
it would within a system including the PWM and dc-to-dc
power converter. Simply connect the current and voltage sense
voltages from the system directly to the board terminus. This
feature is used when setting or evaluating loop compensation
using a field of passive compensation components. Figure 51 is
a photograph of the AD8451-EVA L Z .
FEATURES AND TESTS
SMA connectors provide access for input voltages to the
sensitive instrumentation (IA) and difference (DA) amplifiers.
ISVP and ISVN connectors are the IA inputs, and BVP and
BVN are the DA inputs. These inputs accept the dc voltages
from battery current and voltage measurement sources, or from
a precision dc voltage source. SMA connectors ISET and VSET
are available for precision dc control voltages for CC or CV
battery charging voltages. SMA ISREFLO is available for
applying a nonzero reference voltage to the IA. SMA VCTRL
connects to the input of a dc-to-dc power converter as seen in
Figure 52. Convenient test loops are provided connecting scope
probes or instruments for the remainder of the input/output.
The MODE switch selects between the charge and discharge
option. Figure 52 is a schematic of the AD8451-E VA L Z . Table 6
lists and describes the various switches and functions.
12137-051
Figure 51. Photograph of the AD8451-EVALZ
Rev. 0 | Page 26 of 32
Data Sheet AD8451
Table 6. AD8451-EVALZ Test Switches and Functions
Switch Function Operation
Default
Position
MODE Selects the charge or the discharge
mode.
The MODE switch selects CHG (logic high) or DISCH (logic low). CHG
RUN_TEST1 Selects between the user inputs and
the 2.5 V AD8451 reference voltage.
The AD8451 operates normally when the RUN_TEST1 switch is in the RUN
position. When in the TEST position, 2.5 V is applied to the ISET and VSET inputs.
RUN
RUN_TEST2 Tests the CC or CV loop filter
amplifiers.
The voltage at the VCTRL output (TPVCTRL) for all positions is 0 V when
RUN_TEST1 is in RUN position and 2.5 V when RUN_TEST1 in TEST position.
RUN
ISREF_HI The ISREF_HI switch connects
Pin 74 (ISREFH) to the internal 2.5 V
reference (2.5 position) or to the
SMA connector EXT (the external
input for a user defined VREF input).
When in the 2.5V position, the ISREF_HI switch connects Pin 74 (ISREFH, an
internal 100 kΩ resistor) to Pin 73 (VREF, the 2.5 V reference). When the
ISREF_LO switch is in the NORM position, the output at Pin 71 (ISMEA)
shifts positive by 20 mV.
EXT
ISREF_LO Connects Pin 76 (ISREFL) to ground
(NORM) or to the ISREFL SMA input
connector.
When in the NORM position and the ISREF_HI switch is in the EXT position,
there is no offset applied to the ISMEA output. When in the EXT position,
the ISREFLO SMA is selected.
NORM
EVALUATING THE AD8451
Test the Instrumentation Amplifier
Connect the TPISVN jumper to ground, and then apply
100 mV dc to TPISVP. Measure 2.6 V at the TPISMEA output.
Subtract any offset voltages from the output reading before
calculating the gain.
20 mV Offset at IMEAS Output
Connect a jumper from TPISVP to TPISVN to ground by using
another jumper and any one of the convenient black test loops.
Measure 0 V ± 2.86 mV at the TPISMEA output (that is, the IA
residual offset voltage multiplied by gain). Move the ISREFLO
switch to the EXT position, and the ISREFHI switch to the
20 mV (EXT) position. The output will then increase by 20 m V.
Test the Difference Amplifier
Insert a shorting jumper at Header GND_BVN. With 1 V dc
applied to TPBVP, measure 0.8 V at TPBVMEA. For the most
accurate gain measurement, subtract the offset voltage from the
output voltage before calculating gain.
5 mV Offset at BVMEAS Output
Insert jumpers in the GND_BVP and GND_BVN headers.
Measure 0 V ± 0.4mV at the TPBVMEA output (that is, the DA
residual offset voltage multiplied by gain). Connect a jumper
between TPBREFH and TP2.5V. The output will then increase
by 5 m V.
CC and CV Integrator Tests
Switches RUN_TEST1 and RUN_TEST2 set up the required
circuit conditions to test the integrators. RUN_TEST1 disconnects
the external inputs ISET and VSET and applies 2.5 V dc from
the reference, simultaneously, to both of the CC and CV.
RUN_TEST2 has three positions: RUN, TEST_CC, and
TEST_CV.
Loop Compensation
The AD8451-E VA L Z is suitable for use as a test platform for
system loop compensation experiments. However, before
installing the platform in a system, component changes are necessary.
Note the four compensation networks, CC-CHARGE, CC-
DISCHARGE, CV-CHARGE, and CV-DISCHARGE, located
on the right-hand side of the schematic shown in Figure 52. To
make it easier to locate these components, the configuration of
these networks on the AD8451-EVA L Z PCB approximates that
shown in the schematic (see Figure 52). Each of the components
locations accommodates both standard, 1206 size, surface-mount
chip resistors and capacitors or leaded components inserted into
the pairs of TP thru holes spanning the SM footprints. The TP
holes accept the popular 0.025” test pins if leaded devices are
preferred for multiple loop tests.
As shipped, CC and CV loop amplifier filters are configured as
voltage followers by replacing feedback capacitors to the inverting
inputs with resistors, and removing the dc coupling resistors from
the IA and DA outputs. The feedback loops must be reconfigured
to close the loops to operate as precision feedback loops.
Loop compensation requires knowledge of the output dc-to-dc
power converter. It is assumed that the AD8451 is most often
used with a switching converter. The scope and breadth of this
switching converter design architecture is quite broad, and a
thorough discussion of all the types and variants of this type of
converter is well beyond the scope of this data.
When the circuit and component details of the power converter
are known, proceed with a calculation of the loop parameters
and components, and the values necessary to achieve loop
compensation.
Because the loop is of the type proportional/integrating (PI), a
direct dc path is required from the IA and DA amplifiers to the
error inputs of the CC and CV loop amplifiers. Install these
resistors at the R1, R6, R7, R11, and R12 locations.
Likewise, the CC and CV amplifiers must be reconfigured from
voltage followers to integrators by replacing the 0 Ω capacitors
at C6, C10, C11, C19, and C24 with appropriate capacitors.
Rev. 0 | Page 27 of 32
AD8451 Data Sheet
SCHEMATIC AND ARTWORK
12137-052
−5V
TPISVP
RGP
−5V
C20
1µF
50V
−5V
2.5
C5
10µF
10V
TPISREFLS
TPBVNS
TPBVMEA
NC
BVN
NC
25V
TPBVREFH
TPBREFL
TPBVREFLS
C21
1µF
50V
DISCH
VSET
TPVSETBF
TPISET
ISMEA
C9
0.1µF
50V
ISVP
TPISREFH
ISVN
NC
ISREFL
25 V
TPBVN
BVP
BREFH
BVPS
NC
BREFL
BVP
NC
NC
BVNS
BREFLS
NC
NC
NC
BVMEA
BVN
NC
VREF
AGND
AVEE
AVCC
MODE
ISVP
RGP
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
RGN
ISVN
NC
17
18
15
16
8
7
6
5
4
3
2
14
13
9
12
11
10
19
1
20
59
54
56
60
53
51
49
44
43
41
50
58
46
45
47
55
57
52
48
42
VCTRL
VCLN
VVE1
VINT
VCLP
VVE0
VVP0
VSET
NC
NC
NC
NC
VSETBF
VREF
DGND
DVCC
NC
AVCC
NC
NC
25V
5V
VCTRL
5V
TPVCTRL
TPVCLP
37 40
393834 3635
21 242322 25 28
27
26 30 33323129
RGN
TPISVN
C18
10µF
10V
C19
10µF
10V
80 64 6269 6568 6773 7178 7477 7679 6675 72 70 6163
GND_BVPGND_BVN
EXTNORM
ISREFLO
2.5V
EXT
ISREFHI
TPMODE
TPISREFL
NC
NC
NC
ISREFH
NC
VREF
ISREFLS
ISREFL
NC
IVE1
ISMEA
IVE0
ISET
VINT
ISREFB
NC
NC
AGND
AVEE
AVCC
NC
AVEE
1
2
3
1
2
3
AD8451
X1
TPBVP
MODE
CV -DISCHARGE
TP49TP41 TP61TP55
TP14 TP54
C10*
0Ω
1206
C14
TBD1206
R4
10kΩ
1206
R1
TBD1206
CC -DISCHARGE
IVE0
TP48TP40
C3
TBD1206
TP1
TP53
R3
10kΩ
1206
TP11 TP13
C6*
TBD1206
1206
CC -CHARGE
VINT
TIVE1
TP58 TP62TP43 TP51
R5
10kΩ
1206
R6
TBD1206 C11*
0Ω
1206
C15
TBD1206
TP46 TP57
TP6TP3
TP42 TP50
TVVE1
TP45 TP18
TP56 TP19
C24*
0Ω
1206
R15
10kΩ
1206
C17
TBD1206
R14
10kΩ
1206
TP26 TP25
R12
TBD1206
TP23 TP24
TP30 TP33
C23
TBD1206
CV -CHARGE
BVMEA
VVP
0
TP12TP4R13
10k
Ω
1206
R11
TBD1206
C22
TBD1206
R2
10kΩ1%
1206
TP36
TP7
R7
TBD1206
TP8
TP15
TP9
TP28
C2
TBD1206
TP16 TP37
TP2TP
5
TP10TP29
C1
TBD1206
R8
10kΩ1%
1206
TPISREFB
NC
NC
2.5
5V
+5V
+
C4
10µF
35V
+
AVEE
+
C8
10µF
35V
C7
10µF
35V
AVCC
−5V
DVCC
25 V
VINT
TPVCLN
GND5GND4GND3GND2
GND10
GND6GND7
GND1
TP_BVP
TP32 TP35
TP39TP27
TP59TP47
C13
TBD1206
TP60
C19*
0Ω
1206
R9
10kΩ
1206
TP52TP44 TP63
−5V
GND8GND9
VVE0
TP17 TP38
R10
10kΩ
1206
TP31 TP34
C12
TBD1206
VVP0
5V
CHG
1
23
VSETBF
R17
0
Ω
R16
0
Ω
R18
1k
Ω
CR 1
5.1V
R19
1kΩ
RUNTEST4
5
6
1
2
3
VSET
RUN_
TEST1
ISET
VSET 2
14
3
VINT
TVVE1
VVE1
6
8
5
7
RUN_
TEST2
VVE1
TVVE1
RUN
T_CC
T_CV
CR3
5.1V
R19
1k
Ω
CR2
5.1V
TPISMEA
JP1
DVCCRET AVEERET
AVCCRET
JP 1
BVMEA
*0Ω 1206 RESISTORS ARE TEMPORARILY INSTALLED I N
LOCATIO NS C6, C14, C17, C15, AND C19.
SEE TEXT FO R FURTHER EXPLANATION.
Figure 52. AD8451-EVALZ Schematic
Rev. 0 | Page 28 of 32
Data Sheet AD8451
12137-053
Figure 53. AD8451-EVALZ Top Silkscreen
12137-054
Figure 54. AD8451-EVALZ Primary Side Copper
Rev. 0 | Page 29 of 32
AD8451 Data Sheet
12137-055
Figure 55. AD8451-EVALZ Secondary Side Copper
12137-056
Figure 56. AD8451-EVALZ Power Plane
Rev. 0 | Page 30 of 32
Data Sheet AD8451
12137-057
Figure 57. AD8451-EVALZ Ground Plane
Rev. 0 | Page 31 of 32
AD8451 Data Sheet
OUTLINE DIMENSIONS
COMPLIANT TO JEDE C S TANDARDS MS-026-BE C
1.45
1.40
1.35
0.15
0.05
0.20
0.09
0.10
COPLANARITY
VIEW A
ROTAT E D 90° CCW
SEATING
PLANE
7°
3.5°
0°
6160
180
20 41
21 40
VIEW A
1.60
MAX
0.75
0.60
0.45
16.20
16.00 SQ
15.80
14.20
14.00 SQ
13.80
0.65
BSC
LE AD PIT CH
0.38
0.32
0.22
TOP VIEW
(PINS DOWN)
PIN 1
051706-A
Figure 58. 80-Lead Low Profile Quad Flat Package [LQFP]
(ST-80-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model1 Temperature Range Package Description Package Option
AD8451ASTZ −40°C to +85°C 80-Lead LQFP ST-80-2
AD8451ASTZ-RL −40°C to +85°C 80-Lead LQFP ST-80-2
AD8451-EVALZ Evaluation Board
1 Z = RoHS Compliant Part.
©2014 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D12137-0-3/14(0)
Rev. 0 | Page 32 of 32
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Analog Devices Inc.:
AD8451ASTZ AD8451ASTZ-RL AD8451-EVALZ