STANDARD
MICROCI RCUIT DRAWING SIZE
A
5962-88689
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
C SHEET 4
DSCC FORM 2234
APR 97
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for
non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified
Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional
certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program
plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality
Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or
function of the device. These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as
specified in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.3 Block diagram. The block diagram shall be as specified on figure 2.
3.2.4 Timing waveforms and test circuits. The timing waveforms and test circuits shall be as specified on figure 3.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full case operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-HDBK-103 (see 6.6 herein). For
packages where marking of the entire SMD PIN number is not feasible due to space limitati ons, the manufacturer has the
option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in
compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification
mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 and QML-38535 (see 6.6 herein). The certificate of compliance submitted to
DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements
of MIL-PRF-38535, appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535,
appendix A.
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.